2
91
LED INDICATORS
1
9-
Q19 series
1
-Q
D
IN
Ø19 mm panel mount LED indicators
DISTINCTIVE FEATURES
10 mm colored diffused epoxy lens or 10 mm water clear
super bright LEDs
Prominent and flush bezel styles
(2.8 x 0.8) solder lug/faston terminals, pins or (200 mm long)
wire terminations
Custom engraving available
Available in RGB
ENVIRONMENTAL SPECIFICATIONS
• IP67 sealing option (EN60529)
• Operating & Storage Temperature Range:
Rear plastic body: -30 °C to +65° C ( –22 °F to +149 °F)
Rear epoxy body: -40 °C to +85° C ( –40 °F to +185 °F)
GENERAL SPECIFICATIONS
• Max Reverse Voltage: 5 V
• Viewing Angle: 30–100° (dependant on model)
• Life Expectancy: 100,000 hours
• Torque: 75 cNm
• Maximum panel thickness 11 mm
MATERIALS
• Plated brass bezel finished in bright chrome, black or satin grey and
moulded polycarbonate rear body
MOUNTING
The company reserves the right to change specifications without notice.
All LED characteristics are dependent upon environmental conditions. Therefore published data
should be considered nominal and subject to variations. 1
.
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
ELECTRICAL SPECIFICATIONS
STANDARD LED INTENSITY Voltage Operating Voltage Operating Current
(Min to Max) (Typical All Types)
LED COMPONENT SPECIFICATIONS
02 (No Resistor) 1.8 to 3.3 VDC 20 mA max*
Prominent and
Flush Forward Voltage
Recessed
6 VDC 5.4 to 6.6 VDC 20 mA
HE Red 80 mcd 10 mcd 2.0 V
12 VDC 10.8 to 13.2 VDC 20 mA
Green 60 mcd 5 mcd 2.2 V
24 VDC 21.6 to 26.4 VDC 20 mA
Yellow 50 mcd 4 mcd 2.1 V
28 VDC 25.2 to 30.8 VDC 20 mA
Blue 540 mcd 100 mcd 3.3 V
White 1000 mcd 150 mcd 3.3 V 110 VAC 99 to 121 VAC 6 mA
Orange 80 mcd 200 mcd 2.2 V 220 VAC 207 to 235 VAC 3 mA
Bi-color (Typical)
15/15 mcd 14/10 mcd 2.0 V/2.2 V * Customer to supply resistor for desired operating
(Red/Green)
current.
Tri-color (Typical)
60/50/50 mcd 15/10/30 mcd 2.0 V/2.2 V/2.1 V
(Red/Green/Yellow)
Bi-color - The color is changed by reversing the polarity of the supply voltage.
Tri-color - The indicator has red and green LEDs, when both connected yellow is produced. ADDITIONNAL INFORMATION ON LED COMPONENTS
SUPER BRIGHT LED INTENSITY • The operating voltage must not be exceeded by
more that 10% as this will result in reduced life
LED COMPONENT SPECIFICATIONS expectancy
Prominent and
Recessed
Flush Forward Voltage • Luminous intensity is measured at 20 mA on a
HE Red 17,000 mcd 2,000 mcd 2.0 V
discrete led unless otherwise stated.
Green 11,000 mcd 680 mcd 3.5 V • Luminous intensities and color shades of white
Yellow 4,000 mcd 350 mcd 2.3 V LEDs may vary within a batch.
Blue 2,500 mcd 250 mcd 3.3 V • Luminous intensity will be reduced with lower
White 4,400 mcd 250 mcd 3.3 V operating current.
Orange 2,800 mcd 300 mcd 2.1 V
CONNECTIONS
HYPER BRIGHT LED INTENSITY
LED COMPONENT SPECIFICATIONS REAR EPOXY WIRES FOR RGB OPTION
Prominent and
Flush Forward Voltage M19 x 1.0 THREAD
Recessed
HE Red 2,800 mcd 800 mcd 2.1 V BLACK ANODE +VE
RED CATHODE -VE
GREEN CATHODE -VE
Green 2,200 mcd 250 mcd 3.2 V BLUE CATHODE -VE
Yellow 1,300 mcd 250 mcd 2.0 V
22.0
0.866
Orange 850 mcd 200 mcd 2.1 V
4.8 13.5
RGB LED INTENSITY
0.187 0.531
210
17.5 190
ITEM SYMBOL CONDITION TYP. 0.689 8.268
7.480
VF(R) IF=20 mA 2.1
DC Forward Voltage
VF(B/G) IF=20 mA 3.1
Iv (Red) 220 mdc
Luminous Intensity Iv (Green) 500 mdc
Iv (Blue) 100 mdc
2
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
BUILD YOUR PART NUMBER
SERIES MOUNTING HOLE BEZEL STYLE TERMINALS BEZEL FINISH
19 Ø19 mm Metal Solder Lug/ Fastons 5 Rear epoxy Wires Metal
1 (2.8 x 0.8)
P Prominent 6 Short body Pins C Bright Chrome
2 Pins
R Recessed 7 Short body Wires B Black
3 Wires
F Flush G Satin Grey
4 Rear epoxy Pins
EP Extra Prominent
TYPE OF ILLUMINATION LED COLOR VOLTAGE SEALING
XX Fixed Light R Red
HG
Hyper Bright
SB
Super bright 02 no resistor** (Blank) Unsealed
Green blue
Flashing Light G Green 06 6 VDC E IP67
KK (12 V – 28 VDC) Hyper Bright Super bright
HY Yellow SW white
Y Yellow 12 12 VDC
YY Bi-color
Hyper Bright Super bright
B Blue HO Orange SO Orange 12A 12 VAC/DC
ZZ Tri-color
(Blank) Common cathode
W White Super Bright RG Red/green 24 24 VDC
SR Red -CA Common anode
O Orange RY Red/yellow 24A 24 VAC/DC
Super Bright
SG
HR
Hyper Bright Green
GY Green/yellow 28 28 VDC
Red
Super Bright
SY Red/yellow/ 28A 28 VAC/DC
Yellow RYG green
110 110 VAC
Red/Green/ ** please refer to the
RGB forward voltage in electrical
Blue* 220 220 VAC
specifications
ABOUT THIS SERIES * Terminals option 5 and
common anode only
Notice: please note that not all combinations of above numbers are available.
• Gold faston terminal denotes anode (+), silver terminal denotes • The tri-color led has red and green leds when both are
cathode (-) connected yellow is produced
• Standard wire length is 200 mm, 22 AWG UL1007, red wire • Standard tri-color faston terminals are two anodes (+) and one
denotes anode (+), black wire denotes cathode (-) for other wire cathode (-)
lengths consult APEM • Tri-color wires are one red (+) and one green (+) anode and one
• 110 VAC and 220 VAC, only available with terminal options 1, 3 black (-) cathode
and 5 • Tri-color pins are center (–) cathode, shortest (+) anode pin
• Bi-color leds, by connecting the gold faston (+) one color green, longest (+) anode pin red
is produced, by reversing the supply voltage another color is • We recommend using hyperbright or superbright leds for use at
produced – bi-colors are available up to 28 VDC 110 VAC and 220 VAC
• Take care when soldering to the faston terminals (recommended • For leds with alternative voltages and for multi-voltage options
solder temperature 300 °C - 3 sec) please consult APEM
• Body options 2 and 6 are only available without integral resistor
(02).
3
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
PROMINENT BEZEL SOLDER LUG/FASTON
WIRES PINS
REAR EPOXY WIRES REAR EPOXY PINS
SHORT BODY WIRES SHORT BODY PINS
4
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
FLUSH BEZEL SOLDER LUG/FASTON
WIRES PINS
REAR EPOXY WIRES REAR EPOXY PINS
SHORT BODY WIRES SHORT BODY PINS
5
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
RECESSED BEZEL SOLDER LUG/FASTON
WIRES PINS
REAR EPOXY WIRES REAR EPOXY PINS
SHORT BODY WIRES SHORT BODY PINS
6
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
EXTRA PROMINENT BEZEL SOLDER LUG/FASTON
WIRES PINS
REAR EPOXY WIRES REAR EPOXY PINS
SHORT BODY WIRES SHORT BODY PINS
7
LED INDICATORS
Q19 series
Ø19 mm panel mount LED indicators
CUSTOM ENGRAVING
Some common codes are listed above, for your custom requirements please contact APEM.
Unless specified standard engraving with white infill will be supplied.
Suffix the part number with legend code :
High beam Low beam Rear fog Front fog Windscreen Windscreen Ventilator
-0AJ -097 -027 -026 wiper washer fan
-021 -022 -023
Turn Signal Side lights Horn Hazard Heating Brake test Arrow
-0AH -098 -041 warning -018 -0BU -0K6
-013
ABS
Battery Oil can Windscreen ABS Engine coil Seat belt USB
-0AG -0GP heating -086 -0EL -0SB connection
-020 -0BU
ECU
Steam ECU Side step Air con Engine Boot/Trunk
-0ST -0EU -0AD -012 -040 Release
-0BR
CABLE LENGTH AND CONNECTOR
For custom cable length and
connectors contact APEM.
