INNOLUX DISPLAY CORPORATION

LCD MODULE
S P E CI FI C AT I O N

Customer:
Model Name: NJ101IA-01S
Date: 2023/12/21
Version: 03

□ Preliminary Specification
■ Final Specification

For Customer ’s Acceptance

Appro ved by Comme nt

Appro ved by Reviewed b y Prepared by

Joko.Wang Meng hs uan.L u Yahsi n. hung

Chie n.Chan
 InnoLux copyright 2004
All rights reserved,
Copying forbidden.

Record of Revision
Version Revise Date Page Content
Fin Spec01 20221020 all Final Spec
Fin Spec02 20230818 6 Add power ripple requirement
NA PCBA LVDS layout change to F type
9 Timing Table add note about frame rate range
1 Modify inversion to 1+2line
5 Update VGH/VGL current
8 Update AC Electrical Characteristics table
Fin Spec03 2023/12/21 17 Update Mechanical Drawing(add BLU ID)
CHIMEI INNOLUX
Contents
1. General Specifications ......................................................................................................... 1

2. Pin Assignment ..................................................................................................................... 2

3. Operation Specifications...................................................................................................... 4

3.1. Absolute Maximum Ratings ......................................................................................... 4

3.1.1. Current Consumption........................................................................................... 5

3.1.2. Backlight Driving Conditions .............................................................................. 5

3.2. Typical Operation Conditions ...................................................................................... 6

3.3. Power Sequence ........................................................................................................... 7

3.4. LVDS Signal Timing Characteristics ........................................................................... 8

3.4.1. AC Electrical Characteristics ............................................................................... 8

3.4.2. Timing Table .......................................................................................................... 9

3.4.3. LVDS Data Input Format ..................................................................................... 10

4. Optical Specifications ........................................................................................................ 11

5. Reliability Test Items .......................................................................................................... 15

6. General Precautions ........................................................................................................... 16

6.1. Safety ........................................................................................................................... 16

6.2. Handling ...................................................................................................................... 16

6.3. Static Electricity .......................................................................................................... 16

6.4. Storage ........................................................................................................................ 16

6.5. Cleaning ...................................................................................................................... 16

7. Mechanical Drawing ........................................................................................................... 17

8. Package Drawing ................................................................................................................ 18

8.1. Packaging Material Table ............................................................................................ 18

8.2. Packaging Quantity ..................................................................................................... 18

8.3. Packaging Drawing ...................................................................................................... 19

INNOLUX Date: 2023/12/20 Page:1/19

1. General Specifications

No. Item Specification Remark

1 LCD size 10.1 inch(Diagonal)

2 Driver element a-Si TFT active matrix

3 Resolution 1280 × 3(RGB) × 800

4 Display mode Normally Black, Transmissive

5 Dot pitch 0.0565(W) × 0.1695(H) mm

6 Active area 216.96(W) × 135.60(H) mm

7 Module size 229.46(W) ×149.1(H) ×4.8(D) mm Note 1

8 Surface treatment HC

9 Color arrangement RGB-stripe

10 Interface LVDS

11 Backlight power consumption 4.68W(Typ.)

12 Panel power consumption 0.7W(Typ.) Note 2

13 Weight 270.5 g(Typ)

14 inversion 1+2line

15 IC ILI6192*2+ILI5801*1

Note 1: Refer to Mechanical Drawing.

Note 2: Including power IC consumption, white pattern
INNOLUX Date: 2023/12/20 Page:2/19

2. Pin Assignment
A 40pin connector use for the module electronics interface. The recommended model
connector is FH52-40S-0.5SH or FP260H-040G10M.

Pin No. Symbol I/O Function Remark

1 NC - No connection
2 VDD P Power Supply
3 VDD P Power Supply
4 NC --- Only for INX test
5 NC --- Only for INX test
6 NC --- Only for INX test
7 GND P Ground
8 Rxin0- I -LVDS Differential Data Input
R0-R5, G0
9 Rxin0+ I +LVDS Differential Data Input
10 GND P Ground
11 Rxin1- I -LVDS Differential Data Input
G1~G5, B0,B1
12 Rxin1+ I +LVDS Differential Data Input
13 GND P Ground
14 Rxin2- I -LVDS Differential Data Input B2-B5,HS,VS,
15 Rxin2+ I +LVDS Differential Data Input DE

16 GND P Ground
17 RxCLK- I -LVDS Differential Clock Input
LVDS CLK
18 RxCLK+ I +LVDS Differential Clock Input
19 GND P Ground
20 Rxin3- I -LVDS Differential Data Input R6, R7, G6, G7,
21 Rxin3+ I +LVDS Differential Data Input B6, B7

22 GND P Ground
23 NC --- Only for INX test
24 NC --- No connection
25 GND P Ground
26 NC --- No connection
INNOLUX Date: 2023/12/20 Page:3/19
27 NC --- No connection
28 NC --- No connection
29 AVDD P Power for Analog Circuit
30 GND P Ground
31 LED- P LED Cathode
32 LED- P LED Cathode
33 NC --- Only for INX test
34 NC --- No connection
35 VGL P Gate OFF Voltage
36 NC --- No connection
37 NC --- No connection
38 VGH P Gate ON Voltage
39 LED+ P LED Anode
40 LED+ P LED Anode

I: input, O: output, P: Power

INNOLUX Date: 2023/12/20 Page:4/19

3. Operation Specifications

3.1. Absolute Maximum Ratings

(Note 1)
Values
Item Symbol Unit Remark
Min. Max.

VDD -0.3 6.5 V

AVDD -0.3 18 V

Power voltage VGH -0.3 42 V

VGL -20 0.3 V

VGH-VGL 12 40 V

Operation Temperature TOP -20 70 ℃

Storage Temperature TST -30 80 ℃

LED Reverse Voltage VR --- 5 V Each LED

LED Forward Current IF --- 70 mA Each LED

Note 1: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. Should a module be used with any of the absolute maximum ratings
exceeded, the characteristics of the module may not be recovered, or in an extreme
case, the module may be permanently destroyed.
INNOLUX Date: 2023/12/20 Page:5/19

3.1.1. Current Consumption (White Pattern)

Values
Symbol Unit Remark
Item
Min. Typ. Max.

IGH 0.30 0.68 1.00 mA VGH =12.5V

IGL 0.30 0.63 1.00 mA VGL = -13V

Current for Driver 12.5 25.4 42.0 mA VDD =3.3V

IVDD
24.5 35.9 49.0 mA VDD =2.5V

IAVDD 39.8 68.5 104.6 mA AVDD =8.2V

3.1.2. Backlight Driving Conditions

Values
Item Symbol Unit Remark
Min. Typ. Max.

Voltage for LED backlight VL 16.8 19.5 20.4 V Note 1

Current for LED backlight IL 228 240 252 mA

LED life time - 20000 - Hr Note 2

Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and IL=
240mA.
Note 2: The “LED life time” is defined as the module brightness decrease to 50% original
brightness at Ta=25℃ and IL =240mA. The LED lifetime could be decreased if
operating IL is lager than 240mA.
INNOLUX Date: 2023/12/20 Page:6/19

3.2. Typical Operation Conditions

( Note 1)
Values
Item Symbol Unit Remark
Min. Typ. Max.

VDD 2.3 2.5/3.3 3.6 V Note 2

AVDD 8.0 8.2 8.4 V

Power voltage
VGH 12 12.5 13 V

VGL -12.5 -13 -13.5 V

Input signal voltage VCOM - - - V Note 3

Ripple voltage VRP - - 150 mV Note 4

Input logic high voltage VIH 0.8 VDD - VDD V

Input logic low voltage VIL 0 - 0.2 VDD V

Note 1: Be sure to apply VDD and AVDD to the LCD first, and then apply VGH apply VGL.
Note 2: VDD setting should match the signals output voltage (refer to Note 3) of
customer’s system board.
Note 3: Auto Vcom，no Vcom voltage required.
Note 4:Including signal:VDD、AVDD、VGH、VGL
INNOLUX Date: 2023/12/20 Page:7/19

3.3. Power Sequence

a. Power on:

b. Power off:
INNOLUX Date: 2023/12/20 Page:8/19
3.4. LVDS Signal Timing Characteristics
3.4.1. AC Electrical Characteristics

Values Uni
Parameter Symbol Remark
Min. Typ. Max. t
LVDS Differential input high
RxVTH - - +200 mV
Threshold voltage RXVCM=1.2
LVDS Differential input low V
RxVTL -200 - - mV
Threshold voltage
LVDS Differential input common
RxVCM 1 1.2 1.7-| VID |/2 V
mode voltage
LVDS Differential voltage |VID| 200 - 600 mV
INNOLUX Date: 2023/12/20 Page:9/19
3.4.2. Timing Table

Values
Item Symbol Unit Remark
Min. Typ. Max.

Frame rate
Clock Frequency 1/Tc 63.4 64.5 85 MHz
=60Hz

Horizontal display area tHD 1280

HS period time tH 1309 1322 1664 Tc

HS Width +Back Porch
tHW+ tHBP +tHFP 29 42 384 Tc
+Front Porch
Vertical display area tVD 800

VS period time tv 807 813 1040 tH

VS Width +Back Porch
tvW+ tvBP +tvFP 7 13 240 tH
+Front Porch
Note1: Frame rate is 60±5Hz, PCLK=Vtotal*Htotal*Frame Rate;
Note2: All the above conditions must be met.
INNOLUX Date: 2023/12/20
Page:10/19
3.4.3. LVDS Data Input Format
INNOLUX Date: 2023/12/20
Page:11/19

4. Optical Specifications

Values
Item Symbol Condition Unit Remark
Min. Typ. Max.

θL Φ=180°(9 o’clock) 75 85 -

θR Φ=0°(3 o’clock) 75 85 -
Viewing angle
degree Note 1
(CR≥ 10)
θT Φ=90°(12 o’clock) 75 85 -

θB Φ=270°(6 o’clock) 75 85 -

TON - 10 20 M sec Note 3

Response time
TOFF - 15 30 M sec Note 3

Contrast ratio CR 800 1000 - - Note 4

WX Normal 0.26 0.31 0.36 - Note 2

θ=Φ=0°
Color chromaticity Note 5
WY 0.27 0.32 0.37 - Note 6

Luminance L 500 650 - cd/m² Note 6

Luminance
YU 75 80 - % Note 7
uniformity

Test Conditions:
1. VDD=2.5V, the ambient temperature is 25℃.
2. The test systems refer to Note 2.
INNOLUX Date: 2023/12/20
Page:12/19
3. Mark
Note 1: Definition of viewing angle range
Normal line
θ=Φ=0°

Φ=90°
12 o’clock direction

θL
θT θR
θB

Φ=180° Φ=0°
Active Area

LCM

Fig. 4-1 Definition of viewing angle Φ=270°

Note 2: Definition of optical measurement system. 6 o’clock
The optical characteristics should be measured in dark room.direction
After 30 minutes
operation, the optical properties are measured at the center point of the LCD
screen. (Viewing angle is measured by ELDIM-EZ contrast/Height :1.2mm,
Response time is measured by Photo detector TOPCON BM-7, other items are
measured by BM-5A/ Field of view: 1° /Height: 500mm.)

Photo detector Normal line

θ=Φ=0°

Φ=90°
12 o’clock direction
500mm

Φ=180° Φ=0°
Active Area

LCM

Φ=270°
6 o’clock direction

Fig. 4-2 Optical measurement system setup

INNOLUX Date: 2023/12/20
Page:13/19

Note 3: Definition of Response time

The response time is defined as the LCD optical switching time interval between
“White” state and “Black” state. Rise time (T ON) is the time between photo detector
output intensity changed from 10% to 90%. And fall time (TOFF) is the time
between photo detector output intensity changed from 90% to 10%.

White (TFT ON) Black (TFT OFF) White (TFT ON)

Photo detector output

100%
(Relative value)

90%

10%
0%
TOFF TON

Fig. 4-3 Definition of response time

Note 4: Definition of contrast ratio

Luminance measured when LCD on the " White" state
Contrast ratio (CR) 
Luminance measured when LCD on the " Black" state

Note 5: Definition of color chromaticity (CIE1931)

Color coordinates measured at center point of LCD.

Note 6: All input terminals LCD panel must be ground while measuring the center area of
the panel. The LED driving condition is IL=240mA .
INNOLUX Date: 2023/12/20
Page:14/19

Note 7: 、finition of Luminance Uniformity

Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every
measuring point is placed at the center of each measuring area.
Bmin
LuminanceUniformity(Yu) 
Bmax
L-------Active area length W----- Active area width

L
W/6

L/6 L/3 L/3

W/3
W

W/3

Fig. 4-4 Definition of measuring points

Bmax: The measured maximum luminance of all measurement position.

Bmin: The measured minimum luminance of all measurement position.
INNOLUX Date: 2023/12/20
Page:15/19

5. Reliability Test Items

Item Test Conditions Remark

High Temperature Storage 80℃ 240hrs

Low Temperature Storage -30℃ 240hrs

High Temperature Operation 70℃ 240hrs

Note 1
Low Temperature Operation -20℃ 240hrs Note 2
Note 3
Operate at High Temperature
+60℃, 90%RH 240hrs
and Humidity
-30℃/30 min ~ +80℃/30 min for a total 100
Thermal Shock cycles, Start with cold temperature and end
with high temperature.

1.5G / 10-500 Hz, Sine wave, 30 min/cycle,

Vibration Test
1cycle for each X, Y, Z

Random Vibration :
Package Vibration Test 1Hz~200Hz,Grms=0.53
Half hours for direction of Z.

Height:60 cm
Package Drop Test
1 corner, 3 edges, 6 surfaces

Electro Static Discharge ± 2KV, Human Body Mode, 100pF/1500Ω

Note 1: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but don’t guarantee all of the cosmetic specification.

Note 2: Before cosmetic and function test, the product must have enough recovery time,
at least 2 hours at room temperature.

Note3: Under no condensation of dew.

INNOLUX Date: 2023/12/20
Page:16/19

6. General Precautions
6.1. Safety

Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your
skin or clothes, wash it off immediately by using soap and water.

6.2. Handling

1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to
excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it carefully
to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module surface
with bare hands.
4. Keep a space so that the LCD panels do not touch other components.
5. Put cover board such as acrylic board on the surface of LCD panel to protect panel
from damages.
6. Transparent electrodes may be disconnected if you use the LCD panel under
environmental conditions where the condensation of dew occurs.
7. Do not leave module in direct sunlight to avoid malfunction of the ICs.

6.3. Static Electricity

1. Be sure to ground module before turning on power or operating module.

2. Do not apply voltage which exceeds the absolute maximum rating value.

6.4. Storage

1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or less.
2. Do not store the module in surroundings containing organic solvent or corrosive
gas.
3. Store the module in an anti-electrostatic container or bag.

6.5. Cleaning

1. Do not wipe the polarizer with dry cloth. It might cause scratch.
2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might
permanent damage to the polarizer.
 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
REV EC NUMBER DESCRIPTION DATE
A XXXXXXX First version 2014/12/20 A
XXXXXXX Add balloon 5 & Notes 2015/04/21
XXXXXXX Change the connector type&thickness 2015/09/02
1.Change components area height:from 6.6max to 7.05 max
XXXXXXX 2.Change the buckle position of TOP & BTM Bezel at PCB side
B 3.Modify PCBA tape outline and Label moves to PCB front 2022/06/08 B
INNOLUX

4.Change LCD Driver IC model

XXXXXXX Improve eye pattern:add 5 components to PCBA 2023/03/07
1.Add 2nd connector: FP260H-040G10M (YTOP)
XXXXXXX 2.Improve eye pattern: PCB layout optimization(F-type) 2023/07/31
C 3.Change the dimension of PCBA Label C
XXXXXXX Add BLU ID(Black printing),For Plant Traceability 2023/09/21

D D

E E

F F

G G

H H
7. Mechanical Drawing

I I

J J

K K

L L

M M

N N

O O

P P

Q Q
Page:17/19

GENERAL LINEAR TOLERANCE SELECT DATE SCALE UNIT

1 N PPK PPK DIMENSION LEVEL
1 2 3 N CONTROL DIMENSION
2 N * CPK DIMENSION 1 2023/09/21 1:2 mm
R 0 ~4 0.05 0.1 0.2
SELECT R
Green Product Category LEVEL PART NUMBER or PDM NUMBER DRAWING REV.
4 ~ 14 0.1 0.2 0.2
14 ~ 63 0.1 0.2 0.4 APPROVED Cc01.chen M_NJ101IA-01S_LCM G
63 ~ 250 0.2 0.4 0.6
Date: 2023/12/20

Halogen Free 2 PART DESCRIPTION SHEET NUMBER

Green 4 250 ~ 600 0.6 1.0
CHECKED Xiaonan.gu
See 13QM000020 600 ~ 4000 1.6 LCM_NJ101IA-01S 1of1
S GENERAL ANGULAR TOLERANCE SIZE
S
SELECT
LEVEL 1 2 3 LEVEL DESIGNED Yongsheng.yang
Safety See 13QM000092 RANGE 1 2 3 LEVEL A3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
 INNOLUX Date: 2023/12/20
Page:18/19

8. Package Drawing

8.1. Packaging Material Table

Model Unit
No. Item Dimensions(mm) Quantity Remark
(Material) Weight (kg)

1 LCM Module NJ101IA-01S 229.46*149.10*4.8 0.2705 25 pcs NA

BC Corrugated
2 Partition 512 X 349X 230 1.963 1 set NA
paper
4 Dust-Proof Bag aluminium foil 274 X 250 X 0.07 0.0124 25 pcs NA

5 Drier Montmorillonite 85x47x10 0.011 2 pcs NA

Co r r u g at e d
6 Carton 530 X 367 X 260 0.95 1 p cs NA
pa p e r
7 Total weight 10 Kg ± 5 %

8.2. Packaging Quantity

Total LCM quantity in Carton: No. of Partition （1 Rows X Quantity per Row 25 ）= 25pcs
 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
REV EC NUMBER DESCRIPTION DATE

A A

B B
INNOLUX

C C

Module
D D

Lable

E E

Bend bag to Tape Label

F F
LCM back side .
Al Bag
G G

H H

Partition
I I
8.3. Packaging Drawing

PCBA side Module*25 Corrugated bar

J J

Tape (INNOLUX logo)

K K

Corrugated bar Lable on the

L Drier*2 L
same side

M M

N N

Carton
O O
label

P P

Q Q

SELECT DATE SCALE UNIT

1 N PPK PPK DIMENSION LEVEL
N CONTROL DIMENSION mm
2 N * CPK DIMENSION 2022/08/30
DRAWING REV.
R
(1) Carton Dimensions : 530(L)*367(W)*260(H) PART NUMBER or PDM NUMBER
R
APPROVED jimmy.hung 8B02M001J400N A
PART DESCRIPTION SHEET NUMBER
(2) 25 Modules/Carton CHECKED Jun11.wang ASSY_PACKAGE_ NJ101IA-01S 1/4
S SIZE S
DESIGNED ninghsiung.chiu A1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Page:19/19
Date: 2023/12/20