LCD MODULE

SPECIFICATION
Customer:
Model Name: RXL104064-B
Date: 2017/03/03
Version: 01
■Preliminary Specification
□Final Specification
For customer’s Acceptance

APPROVED BY Comment

APPROVED BY Reviewed BY Prepared BY

-1-
 Record of Revision

Version Revise Date Page Content

Pre-spec.01 2017/3/3 Initial Release

-2-
 Contents
1. General Specifications………………………………………………………….4
2. Pin Assignment…………………………………………………………………...5
3. Operation Specifications…………………………………………………….....6
3.1 Absolute Maximum Rating………………………………………............6
3.2 Typical Operation Conditions…………………………………………….8
3.3 Current Consumption……………………………………………………...9
3.4 Backlight Driving Conditions……………………………………………..9
3.5 Power Sequence…………………………………………….………….....9

3.6 AC Characteristics…………………………………………………….….10
3.6.1 Data Timing………………………………………………....10
3.6.2 AC Electrical characteristic……………………………….11
3.6.3 Input Clock and Data Timing Waveform………………..12
4. Optical Specifications…………………………………………………………...13
5. Reliability Test Items……………………………………………………………..17
6. General Precautions………………………………………………………….....18
6.1. Safety………………………………………………………………………..18
6.2. Handling…………………………………………………………………….18
6.3. Static Electricity……………………………………………………………18
6.4. Storage……………………………………………………………….……...18
6.5. Cleaning…………………………………………………………................18
7. Mechanical Drawing……………………………………………………………..19
8. Package ……………………………………………………………………………20
8.1. Packaging Material Table…………………………………………………20
8.2. Packaging Drawing…………………………………………………………21

-3-
1. General Specifications

NO Item Specification Remark

1 LCD Size 10.4 inch (Diagonal)

2 Driver element a-Si TFT active matrix

3 Resolution 800 x 3(RGB )x 600

4 Display mode Normally White, Transmissive

5 Dot pitch 0.088(W) × 0.264(H) mm

6 Active area 211.2(W) × 158.40(H) mm

7 Module size 228.4 (W) x175.40(H) x5.9 (D)mm Note 1

8 Surface treatment Anti-Glare

9 Color arrangement RGB-stripe

10 Interface TTL

11 Backlight power consumption 2496 mW

12 Panel power consumption 800 mW

13 Weight TBD

Note 1: Refer to Mechanical Drawing

-4-
2. Pin Assignment
TFT LCD Panel Driving Section
FPC Connector is used for the module electronics interface. The recommended model is
FH12A-60S-0.5SH manufactured by Hirose.
Pin NO Symbol I/O Function Remark
1 GND Ground
2 VCC +3.3V Power
3 VCC +3.3V Power
4 NC NC
5 NC NC
6 NC NC
7 GND GND
8 RXIN0- LVDS Signal(-) - channel 0
9 RXIN0+ LVDS Signal(+) - channel 0
10 GND Ground
11 RXIN1- LVDS Signal(-) - channel 1
12 RXIN1+ LVDS Signal(+) - channel 1
13 GND Ground
14 RXIN2- LVDS Signal(-) - channel 2
15 RXIN2+ LVDS Signal(+) - channel 2
16 GND Ground
17 RXCLKIN- LVDS Clock Signal(-)
18 RXCLKIN+ LVDS Clock Signal(+)
19 GND Ground
20 NC NC
21 NC NC
22 GND Ground
23 GND Ground
24 NC NC

-5-
 25 NC NC
26-30 NC NC
I: input, O: output, P: power
Note 1: DE/SYNC mode select .Normally pull high .
When select DE mode, MODE= “1”, VS and HS must pull high.
When select SYNC mode, MODE= “0”, DE must be grounded.
Note 2: When input 18bits RGB data, the two low bits of R,G and B data must be grounded.
Note 3: Data shall be latched at the falling edge of DCLK.

3. Operation Specifications
3.1. Absolute Maximum Ratings
Values
Item Symbol Unit Remark
Min. Max
Power voltage VDD -0.3 3.9 V

Operation Temperature TOP -20 70 ℃

Storage Temperature TST -30 80 ℃

1 msec 脉冲，1/10 占空比

LED Peak forward current Ifp - mA
1 msec Plus 10% Duty Cycle

LED Absolute maximum

Ifm - mA
Forward current
Pd
LED Power dissipation mW

Note1 :The absolute maximum rating values of this product are not allowed to be exceeded at
any times. Should a module be used with any of the absolute maximum ratings
Exceeded, the characteristics of the module may not be recovered, or in an extreme case,
the ,module may be permanently destroyed.
Note 2 : For operation above 25℃,The Ifm Ifp & Pd must be derated,the Current derating is
-0.36mA/℃ for DC drive and-0.86mA/℃ for Pulse drive, the Power dissipation is
-0.75mW/℃.The product working current must not more than the 60% of the Ifm or Ifp
according to the working temperature.

-6-
 3.2. Typical Operation conditions
Values
Item Symbol Unit Remark
Min. Typ. Max

Power voltage VDD 3.0 3.3 3.6 V Note2

Input logic high voltage VIH 0.8DVDD - 3.6 V

Note3
0.2
Input logic low voltage VIL 0 - V
DVDD
Note 1: Be sure to apply VDD and VGL to the LCD first, and then apply VGH.
Note 2: VDD setting should match the signals output voltage (refer to Note 3) of
customer’s system board.

3.3. Current Consumption

Values
Item Symbol Unit Remark
Min. Typ. Max

Current for Driver IvDD - 150 280 mA VDD=3.3V

3.4.Backlight Driving Conditions

-7-
 Values
Item Symbol Unit Remark
Min. Typ. Max
Voltage for LED
VL (8.5) (9.0) (9.6) V Note1
backlight

Current for LED

IL - (360) - mA
backlight

LED life time - - 20000 - Hr Note2

Note1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and IL =360mA.
Note1: The LED life time” is defined as the module brightness decrease to 50% original
brightness at Ta=25℃、60±20%RH and IL =360mA.The LED lifetime could be decreased if
operating IL is lager than 360mA

3.5. Power Sequence

The LCD panel power ON/OFF sequence is as below

-8-
 3.6. AC Characteristics

3.6.1. Data Timing

Values
Item Symbol Unit Remark
Min Typ Max

Clock Frequency 1/Tc - 50 (65) MHz

Horizontal display area tHD 1024 Tc

HS period time tH (1200) 1344 (1400) Tc

tHW
HS Pulse Width (1) - (140) Tc

-9-
Back Porch tHBP 160 Tc

Front Porch tHFP 16 160 215 Tc

Vertical display area tVD 768 tH

VS period timE tv (778) 806 (842) tH

VS Width tvW 2 - 20 tH

Back Porch tvBP 23 tH

Front Porch tvFP (1) 15 (49) tH

Horizontal Timing

- 10 -
3.6.2. AC Electrical characteristic

- 11 -
3.6.3. Input Clock and Data Timing Waveform

- 12 -
4. Optical Specifications
Values
Item Symbol Condition Unit Remark
Min. Typ. Max

θ L Φ=180° 80 85 -

Viewing angle θ R Φ=0° 80 85 -

degree Note1
(CR≥10)
θ T Φ=90° 80 85 -

θ B Φ=270° 80 85 -

Ton - 10 20 msec Note3

Response time
Toff - 15 30 msec Note3

Contrast ratio CR 300 500 - - Note4

Normal
Wx 0.26 0.31 0.36 - Note2
θ =Φ=0°
Color chromaticity Note5
Wy 0.28 0.33 0.38 - Note6

Luminance L - 400 - Cd/m2 Note6

Luminance
Yu 70 75 - % Note7
uniformity

Test Conditions:
1. VDD=2.5V,1L=360mA(Backlight current),the ambient temperature is 25℃.
2. The test systems refer to Note2.

- 13 -
Note 1:Definition of viewing angle range

- 14 -
- 15 -
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.

Note 6: All input terminals LCD panel must be ground while measuring the
center area of the panel. The LED driving condition is IL=280mA .

- 16 -
- 17 -
5. Reliability Test Items

Item Test Conditions Remark

High Temperature Storage Ta=80℃ 240hrs Note 1，Note 4
Low Temperature Storage Ta=-30℃ 240hrs Note 1，Note 4
High Temperature Operation Ts=70℃ 240hrs Note 2，Note 4
Low Temperature Operation Ts=-20℃ 240hrs Note 1，Note 4
Operate at High Temperature
+60℃,90%RH 240hrs Note 4
and Humidity
-30℃/30min~+80℃/30min for total
Thermal Shock 100cycles,Start with cold temperature and Note 4
end with high temperature.
ISTA-3A 1Hz~200Hz,Grms=0.53
Vibration Test
Half hours for direction of Z.
100G 6ms,±X, ±Y, ±Z 3 times for each
Mechanical Shock
direction
C=150pF,R=300Ω ,8point/Panel
Electro Static Discharge Contact:± 4KV, 5times, Human Body Mode
Air : ± 8KV, 5times, Human Body Mode
(Environment :15℃~35℃,30%~60%)
Note1:Ta is the ambient temperature of samples.
Note2:Ts is the temperature of panel’s surface.
Note3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation, but
don’t guarantee all of the cosmetic specification.
Note4: Before cosmetic and function test, the product must have enough recovery time, at
least 2 hours at room temperature.

- 18 -
- 19 -
7. Mechanical Drawing

- 20 -
 REV DESPRIRTION DATE
0 17.03.03

1 GND

2 VCC

3 VCC

4 NC

5 NC

6 NC

7 GND

8 RXIN0-
10.4''TFT 9 RXIN0+
1024*R.G.B.*768 10 GND

VIEWING ANGLE 11 RXIN1-

12 RXIN1+
ALL 13 GND

14 RXIN2-
LVDS-30RL-GF OR Compatible
15 RXIN2+

WHITE 16 GND

30 1
17 RXCLKIN-

18 RXCLKIN+

- 21 -
19 GND

20 NC

21 NC

22 GND

23 GND

24 NC

25 NC

26 NC

27 NC

28 NC

29 NC
NOTES:
30 NC
1. DISPLAY TYPE:262K/TFT Transmissive,Normal White
2. VIEWING DIRECTION: ALL
LED Logic Circuit
3. LCD CONTROLLER: TBD
4. BACKLIGHT: 14*3 PCS WHITE LED
5. OPERATING TEMP.: -20°C -- 70°C
6. STORAGE TEMP.: -30°C -- 80°C
7: UNMARKED TOLERANCE:±0.3 DRAWN SUE DRAWING NO.

8: 产品需符合“ROHS”标准 UNMARKED FILLET RADIUS: R=0.5 CHECKED DESCRIPTION LCM OUTLINE

9: “*”为重点尺寸，“（）”为参考尺寸
APPROVED UNIT :mm PAGE : 1/1
 8.1. Packaging Material Table

Unit
Model Dimensions(m
No. Item weight Quantity Remark
(Material) m)
(kg)
1 LCM Module RXL104067-B 228.4*175.4*5.9 TBD 50pcs

BC Corrugated
2 Partition TBD TBD 1est
paper
Corrugated
3 BC Corrugated paper TBD TBD 4pcs
Paper
Corrugated
4 BC Corrugated paper TBD TBD 4pcs
Bar
Dust-Proof
5 PE TBD TBD 1pcs
Bag
6 A/S Bag PE 235*180*0.2 0.002 40pcs
7 Carton Corrugated paper 590*360*210 TBD 1pcs
8 Total weight TBD

- 22 -
8.2 . Packaging Drawing

- 23 -