HINABANGAN NATONAL HIGH SCHOOL

Hinabangan, Samar

3RD QUARTER EXAMINATION

TLE-8 (CARPENTRY)
S.Y. 2023-2024

Name: _____________________________________________ Year & Section: _____________________________

Subject: ______________________________ Date: ___________________ Score: ________________________

Test-I(Multiple choice)
Direction: Choose the letter of the correct answer. Write your answer on a separate sheet
1. A carpentry tool used to drive and pull-out nails is______.

A. Spirit Level C. Claw Hammer

B. Drill bit D. Crow Bar
2. A Cutting tool that is used to cut metal pipes and pvc pipes.
A. Cross cut saw C. Rip saw
B. Hack Saw D. Key hole saw
3. It is used to measure long distances in metric and English system________.
A. T-square C. L-square
B. tape measure D. Pull-push rule
4. A list of all things needed in a project together with their descriptions_______.
A. Quantity of materials C. Bill of materials
B. Cost of materials D. Unit price of materials
5. It is a tool used for vertical alignment_______.
A. Plumb bob C. Pull push rule
B. Spirit Level D. Compass
6. States the detailed name of materials.
A. Total C. Description
B. Quantity D. Amount

7. In purchasing material what kind of measure is used________.

A. Description C. Amount
B. quantity D. Unit
8. It gives the price of materials in the BILL OF MATERIAL_________.
A. Amount C. Quantity
B. Description D. Unit cost
9. Which of the following is an example of a tool______?
A. Cement C. Water
B. Spirit Level D. Apron
10. Chisel belongs to___________?
A. Edge Cutting tool C. Hand Driving tool
B. Tooth-Cutting tool D. Boring tool
11. How many parts does a bill of material have______?
A. 4 C. 6
B. 5 D. 7
12. Which of the following is the marking lining tool________?
A. File C. Cross cut Saw
B. Planer D. Marking Gauge
13. Caliper is also known as a _____.
A. Marking Lining Tool C. Miscellaneous Tool
B. Edge Cutting Tool D. Measuring Tool
14. A tool used to bore holes______.
A. Auger Bit C. Spoke shave
B. C-clamp D. Steel Square
15. A Handsaw Used to cut the wood across the grain_______.
A. Hack saw C. Planer
B. Cross-cut saw D. Chisel
16. Which of the following belongs to the PPE or (Personal Protective Equipment)
A. Electric Drill C. Apron
B. Oil Stone D. Nail Set
17. Which of the following are the Driving tools______?
A. Mallet, Nail set, Claw Hammer C. Sander, Router, Jig Saw, Circular Saw, Electric
Drill
B. Goggles, Ear Protector, face mask Router , D. Oil Stone, Files, Paint Brush, Nail Set,
Saw Set
18. Among the four Edge Cutting tools. Which of them is made of rectangular piece of steel with
two cutting edge used in working flat and curved shapes________.
A. Planer B. Chisel C. Spoke shave D. Cabinet Scrapper
19. A tool used to measure Short pieces of stock______?
A. Meter Stick C. Caliper
B. Ruler D. Try Square
20. What Measuring tool is used to lay-out angles_____?
A. Compass C. Protractor
B. Pull-Push Rule D. Meter Stick
21. A measuring tool used to measure 1 meter in length.
A. Pull-push rule B. Caliper C. Meter Stick D. Ruler
22. Which of the following measuring tools is used to check the flatness and squareness of
surface.
A. Plumb bob B. Triangles C. Spirit Level D. L-square
23. What is the major rule of a divider as a carpentry tool.
A. It is used to Inscribe Circles C. It is used to divide distances.
B. It is used to level the flatness of a stock D. It is used Check the vertical
alignment of a stock
24. A tool used in scribing arcs and circles.
A. Screw Driver B. Mallet Hammer C. Meter Stick D. Compass

25. It is also known as the unit in Metric system.

A. Unit Price B. Centimeters C. English System D. board Foot
26. Among the choices below, which one is true about end 1 to end 2 or AB of a lumber.
A. It is the Width Of a lumber C. It is the Thickness of a lumber.
B. it is the Length of a lumber D. It is the flatness of a lumber.
27. In the six (6) faces of a lumber, Edge1 and Edge2 represent as_____.
A. Height B. Width C. Thickness D. Surface
28. Surface 1 and surface 2 or EF of a lumber is also known as_____.
A. Height/Thickness B. Squareness C. width D. Length
29. What will be the equivalent if you convert 1 meter to Feet?
 A. 3. Feet and 3 inches B. 2 feet C. 2.5 feet D. 3.5 feet
30. What will be the equivalent if you will convert 1 ¾” to Centimeters?
A. 1.075 cm. B. 1.750 cm. C. 1.175 cm. D. 1.75 cm.

31. It is the condition where high standard of good housekeeping is maintained so that
there is no dust and rust anywhere.
A. sort B. systematize C. sweep D. sanitize

32. Which is practiced when your colleagues decide with you which things to put where
taking into account the flow of your work?
A. sort B. systematize C. sweep D. sanitize
33. It ensures the safety of the construction workers.
A. signs, signal & barricades C. exit signs
B. danger signs D. safety instructions signs
34. Which shall be used when an immediate hazard exists?
A. signs, signal & barricades C. exit signs
B. danger signs D. safety instructions signs
35. Which shall be used as temporary means of warning an existing hazard such as
defected tools, equipment, etc?
A. danger Signs C. traffic signs
B. accidental Prevention Tags D. directional signs
36. Your employer must conduct a hazard assessment in order to ___________.
A. avoid accident C. eliminate workers
B. promote accident D. None of the above
37. OSH means _______________.
A. Occupational Service Healthy C. Occupational Safety and Health
B. Occupational Safe and Healthy D. None of the above
38. Identifying hazards makes you_________________.
A. safe from working C. work efficient
B. comfortable while working D. all of the above
39. Who should first know about the accident that happened in your shop?
A. principal B. nurse C. teacher D. doctor
40. Accidents can be prevented ____________________.
A. through proper care and maintenance of tools and equipment
B. right attitude toward work
C. if you have a good knowledge about safety practices
D. None of the above

-TEST ENDS-

Prepared by: Checked by:

VICTOR A. ABNATAO JR. CESARIO A. UY JR.

SST-III/TLE TEACHER MT-I/TLE Coordinator

Approved by:

JORGE N. PANICAN
SCHOOL HEAD
 ANSWERS KEY:
G8-CARPENTRY

1.C 16. C
2. B 17. A
3. D 18. D
4. C 19. B
5. A 20. C
6. D 21. C
7. D 22. D
8. D 23. C
9. B 24. D
10. A 25. B
11. B 26. B
12. D 27. B
13. D 28. A
14. A 29. A
15. B 30. D

TEST- II (ENUMERATION)
31. TOP VIEW
32. FRONT VIEW
33. RIGHT-SIDE VIEW
34. 30 X 60 X 90 TRIANGLE
35. 45 X 45 X 90 TRIANGLE
36. APRON
37. GLOVES
38. GOGGLE
39. HELMET
40. BOOTS
FACE MASK
RESPIRATOR