Engineering Adhesives
Technical Data Sheet
Swift®col 2035
General Properties Technology/Base polychloroprene rubber, solvent borne
Type of Product cold contact adhesive
Curing physical
Parts one part system
Color brown
Product Benefits very high contact bonding
good resistance to humidity
high heat resistance
toluene free
Technical Data
General
Physical Properties
Density 0.82 g/cm3
Solid-content by weight 20 % Kö-test method 100035
Processing Guidelines and Parameters
Storage Temperature 10 °C to 25 °C
Processing Temperature 15 °C to 30 °C
Flash off time / waiting time 5 min to 10 min
Viscosity 450 mPa·s Brookfield RVT, 20 °C
Required spray pressure 5 bar to 6 bar
Consumption 250 g/m2 to
300 g/m2
Cured Material Characteristics
Heat resistance 130 °C Kö-test method 100098
Product Properties
Processing Suitable Substrates chipboard
various aluminum alloys
various steel alloys
wood
various other substrates
Consistency liquid
sprayable
Surface Requirements dry
clean
free of grease
Application Method spraying
Cleaning Cleaner for Tools Körasolv CR
Hints Compatibility with Polystyrene Foams Not suitable for bonding polystyrene foams.
Please ask your local sales office for products
suitable for such applications.
TDS Swift®col 2035 | V00.001.eng.002 1/2
Engineering Adhesives
Technical Data Sheet
Additional Information
Storage Processing
Swift®col 2035 should be used within the shelf life spec- Apply adhesive evenly with a suitable application method
ified on the packaging. The storage stability only applieson the two parts to be bonded. After the recommanded
to material stored under appropriate conditions (original waiting time (flash off time) put the parts accurately to-
unopened containers, recommended storage temper- gether and press. The waiting time depends on the
ature). High temperatures shorten the shelf life. Low ambient temperature, thickness of the adhesive film and
temperatures temporary cause a higher viscosity. absorbency of the surfaces. The surfaces to be bonded
should be placed together when the adhesive film is still
Safety slightly sticky but does not stick to the finger when it is
pressed lightly. The parts have to be bonded together at
Please read our material safety data sheet and the labels least within the open time.
of each product before use. The valid safety regulations
must be considered.
Cleaning
Preparation
Clean tools immediately after use. Appropriate cleaners
The surfaces to be bonded must be dry, clean and free are listed in the product properties table. For further
of grease in order to ensure a reliable bonding. information please contact your local sales office.
Connecting what matters.TM
IMPORTANT: Information, specifications, procedures and recommendations provided (“information”) are based on our
experience, and we believe this information to be accurate. No representation, guarantee or warranty is made as to the
accuracy or completeness of the information or that use of the product will avoid losses or damages or give desired results.
It is purchaser’s sole responsibility to test and determine the suitability of any product for the intended use. Tests should be
repeated if materials or conditions change in any way. No employee, distributor or agent has any right to change these facts
and offer a guarantee of performance.
® and ™ are trademarks of H.B. Fuller Company or one of its affiliated entities.
NOTE TO USER: by ordering/receiving product, you accept the H.B. Fuller General Terms and Conditions of Sale applica-
ble in the region. Please request a copy if you have not received this documentation. These Terms and Conditions contain
disclaimers of implied warranties (including but not limited to disclaiming warranties of fitness for a particular purpose) and www.hbfuller.com
limits of liability. All other terms are rejected. In any event, (1) the total aggregate liability of H.B. Fuller for any claim or
series of related claims, however arising, in contract, tort (including negligence), breach of statutory duty, misrepresentation, ©H.B: Fuller Company, 2018
strict liability, or otherwise, is limited to replacement of affected products or refund of the purchase price for affected
products. (2) H.B. Fuller shall not be liable for loss of profit, loss of margin, loss of contract, loss of business, loss
of goodwill, or any indirect or consequential losses arising out of or in connection with product supply. (3) Nothing in
any term shall operate to exclude or limit H.B. Fuller’s liability for fraud, gross negligence, death, or personal injury caused by
negligence, or for breach of any mandatory implied terms unless permitted by law.
TDS Swift®col 2035 | V00.001.eng.002 2/2
