POLYCOAT RBE 15

(SBS Modified Bitumen Emulsion)

Polycoat RBE 15
SBS modified bitumen emulsion
Emulsified bituminous coating which dries to form a tough and seamless,
flexible water and vapor proof protective coating. CA
NC
ONTRIBU
TE

TO
CT

OB
S PRODU

TAINING
THI
LEED
®
DUBAI GREEN BUILDING REGULATIONS
Certificate No. CL17020460
C R E D IT S

CHARACTERISTICS
► Cold applied.
► Single component, easy to apply.
► Can be applied on damp substrates.
► Asbestos free, odorless. Can be applied in closed or
confined spaces.

TDS_Polycoat RBE 15_GCC_0523

► Water-based and therefore is non-toxic.
► Environmentally friendly.
► Good resistance against chloride and sulphate ions.
► Has good adhesion to most building substrates.
► Seamless/joint free.

waterproofing

DESCRIPTION 1
Polycoat RBE 15 is an emulsified bituminous coating
modified with 10% Styrene Butadiene Styrene Rubber, which may be used to clean the surface of all the contaminants
dries to form a tough and seamless, flexible water and depending on the degree of contamination on the surface
vapor proof protective coating. to be coated.
All surface imperfections and protrusions shall be removed
FIELDS OF APPLICATION and repaired. Structurally unsound and friable concrete
Can be used for a wide variety of applications, which must be removed and repaired with a suitable Polycrete*
includes the following: concrete repair mortar.
– waterproofing & protective coating on shallow Priming
foundations. It is highly recommended to apply a priming coat prior
– as damp proof membrane in sandwich construction. to the application of the Polycoat RBE 15 coating on the
– waterproofing in wet areas such as toilets, kitchens etc. substrate. The primer can be prepared in the site by diluting
– curing compound on freshly cast concrete structures Polycoat RBE 15 with 20% water and applying this diluted
coat as the primer. For very dry and porous substrates
– general vapor proof coating
apply two coats of this primer. The primer can be applied
ENVIRONMENTAL INFORMATION to damp or freshly cast concrete surfaces also. However,
it should not be applied on waterlogged or flowing water
Contributes toward satisfying LEED® v4 requirements
areas. Further coats shall be applied only after the primer
of the EQ Credit- Low-emitting Materials (for the VOC
coat dries off completely. In case of delay in application of
content).
the top coat for more than 24 hours, a fresh coat of primer
APPLICATION INSTRUCTIONS shall be re-applied.
Application procedures may vary slightly depending upon Foundation Waterproofing
site conditions. The general recommended guideline for the Stir the contents of the drum thoroughly before application
application of the bitumen coating system is as follows: to remove all sediments. Depending on the dry film
Surface preparation thickness required, apply the rubberized bitumen coating
The surface shall be cleaned thoroughly of all contaminants @1–2m²/L/coat at required no. of coats. On vertical
like dust, traces of curing compound, oil, grease. Light areas, it is recommended to apply the coating in multiple
mechanical grinding/grit blasting/high pressure water jet layers in order to avoid sagging of the heavy bodied

95
 coating. Subsequent coats shall be applied only after the SUPPLY
previous coat dries off completely and shall be applied at
right angles to the previous coat. Clean dry sand may be Polycoat RBE 15 20L pail & 200L drums
broadcasted onto the wet coating to provide a key for the Bituboard 3.2mm 2m x 1m, wt 7.7kg
subsequent coats and achieve a greater dry film thickness. 6.0mm 2m x1 m, wt 14.0kg
The coating should be applied and finished up to the
Watertite TS 15 10m x 50mm, wt 0.60kg
DPC level. If a plaster or cement render is to be applied
on the bitumen coated surface, clean dry sand shall be # Approximate weight
broadcasted on to the coating whilst it is still wet. Leave
TECHNICAL PROPERTIES
the coating for curing for a minimum period of 48 hours
before applying any protection board or backfilling. Care PROPERTIES VALUES TEST
shall be taken to ensure that the first coat is not punctured STANDARDS
during the application of the second coat. However, if the Color Dark Brown -
coating is damaged, the area can be readily over coated
Form Thixotropic
provided the surface preparation is done properly.
viscous liquid -
Protection Density @25°C, [g/cc] 1.00±0.05 ASTM D 1475
Polycoat RBE 15 coating should be protected from getting
Solid content, [% by wt] >65 ASTM D 2939
damaged due to the ongoing site activities and during
backfilling. Rubber content, [%] >10 on
Coating can be protected either by a cement sand the dried
screed (50mm thick) or by an asphaltic protection board film. ASTM D 297
(Bituboard*). Alternatively, a 1000 gauge polythene sheet Elongation, [%] > 500 ASTM D 412
can also be used for protecting the coating in areas where Drying time
TDS_Polycoat RBE 15_GCC_0523

the backfill material is not very coarse. @25°C, [minutes] 60 -

Note: Curing efficiency of Bitumen based emulsions will not
Application
be high as that of Resin based curing compounds
temperature [°C] 5 to 55 -
COVERAGE Service temperature [°C] -5 to 100 -
The coverage varies depending on the type of use: VOC [g/l] <50 ASTM D3960/
General use : 1-2 m²/L/coat at required no. of coats D2369
CLEANING All values given are subject to 5-10% tolerance
Clean all tools immediately after use with clean water. Apart from the information given here it is also important to observe the relevant
Hardened material can be cleaned with a suitable cleaner. guidelines and regulations of various organisations and trade associations as
2 well as the respective standards. The aforementioned characteristics are based
STORAGE & SHELF LIFE on practical experience and applied testing. Warranted properties and possible
uses which go beyond those warranted in this information sheet require our
The pails and drums must be stored in a covered written confirmation. All data given was obtained at an ambient and material
area, away from direct sunlight, UV and other sources temperature of +23°C and 50 % relative air humidity at laboratory conditions
unless specified otherwise. Please note that under other climatic conditions
of heat. The shelf life of the product is up to 12 hardening can be accelerated or delayed.
months in un-opened condition and when stored as The information contained herein, particularly recommendations for the
handling and use of our products, is based on our professional experience.
per recommendations. Failure to comply with the As materials and conditions may vary with each intended application, and
recommended storage conditions and excessive exposure thus are beyond our sphere of influence, we strongly recommend that in each
to sunlight and UV will result in the deterioration of the case sufficient tests are conducted to check the suitability of our products
for their intended use. Legal liability cannot be accepted on the basis of the
quality of the product and reduce its shelf life. contents of this data sheet or any verbal advice given, unless there is a case
of wilful misconduct or gross negligence on our part. This technical data sheet
HEALTH & SAFETY supersedes all previous editions relevant to this product.
As with all bitumen products caution should always be
exercised. Protective clothing such as gloves and goggles
should be worn. (See packing for specific instructions).
Treat any splashes to the skin or eyes with fresh water
immediately. Should any of the products be accidentally
swallowed, do not induce vomiting. Call for medical help
immediately. Ensure that the container is available for
medical attendant to examine any relevant instructions and
content details.

Henkel Polybit Industries Ltd.; PO Box: 293, Umm Al Quwain, UAE

Tel:+971(6)76 70 777; Fax:+971(6)76 70 197; henkelpolybit@henkel.com
Henkel Polybit Industries Ltd.; PO Box: 5911, Dammam-31432, KSA
Tel:+96613808 4061 / 62, Fax: +966 13 812 1164; polybitdammam@henkel.com
www.henkelpolybit.com
96
MS_Polycoat-RBE 15_GCC_0917_GR0
Revised Date : April 2024

METHOD STATEMENT
POLYCOAT RBE 15
SECTION I: GENERAL INSTRUCTIONS
• The quality of the coating is dependent on the substrate and material temperature.
• All materials whether loose or on pallets have to be stored in a covered area and protected from
UV and sunlight. Deterioration of the product may be caused due to improper storage and at high
temperatures.
• Application of coating should be avoided in case of extreme weather conditions like sand storm or
rain.
• The ambient temperature during application should be between 5°C and 55°C.
The following Equipment’s are required during application:
Protective clothing:
Gloves, face mask, overalls, and safety goggles
Application equipment’s:
∼ Slow speed drill machine with less than 500 rpm with a suitable spiral mixer
∼ Wooden press & lap rollers
∼ Brush /roller
∼ Steel scrapper
∼ Cotton waste
∼ Solvent cleaner
∼ Measuring tape
∼ Cutting knife, scissors
SECTION II: APPLICATION INSTRUCTIONS
Surface Preparation:
The surface should be free of any cement laitance, oil, grease, curing compound and any other
deleterious materials.
Light mechanical grinding / grit blasting / high pressure water jet may be used to clean the surface
to be coated, based on the degree of contamination.
Nail heads and other protrusions that are likely to damage the coating must be removed or ground.
Structurally unsound and friable concrete must be removed and repaired. Honey combed or
spalled concrete, surface irregularities, blow holes to be repaired with a suitable POLYCRETE
concrete repair mortar.
Priming:
It is highly recommended to apply a priming coat prior to the application of POLYCOAT RBE 15.
The priming coat is made by diluting POLYCOAT RBE 15 with 20% clean water.
Application:
Stir the contents of the drum thoroughly before application to remove all sediments.
POLYCOAT RBE 15 may be applied by brush, roller or squeegee. It may be applied on damp
surface but ensure that there is no water logging. The coating is normally applied in two coats.
After the application of the first coat, apply the second coat at right angles to the first coat and only
after the first coat has dried completely. On vertical areas, apply the coating in multiple layers to
avoid sagging.
If cement sand render or plaster will be applied on top of the coating, then in order a better key for
bonding it is recommended to broadcast the coating with clean dry sand whilst the coating is still
wet.
MS_Polycoat-RBE 15_GCC_0917_GR0
Revised Date : April 2024

Clean all tools immediately with water after use. Hardened materials can be removed mechanically
only.
It is recommended to protect the applied coating from getting damaged during backfilling. Such
protection can be provided by suitable protective materials like cement sand screed or an asphaltic
protection board (BITUBOARD) or any other material as specified in the project specification.
Safety Data Sheet according to (EC) No 1907/2006 as amended
Page 1 of 12

SDS No. : 563770

POLYCOAT RBE-15 V003.0
Revision: 09.06.2021
printing date: 29.04.2024
Replaces version from: 17.05.2021

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier
POLYCOAT RBE-15
1.2. Relevant identified uses of the substance or mixture and uses advised against
Intended use:
Bituminous product

1.3. Details of the supplier of the safety data sheet

Henkel Jebal Ali FZCO
PO Box 61341 - Jebel Ali
Dubai

Utd.Arab.Emir.

psra.imea@henkel.com
For Safety Data Sheet updates please visit our website https://mysds.henkel.com/index.html#/appSelection or www.henkel-
adhesives.com.

1.4. Emergency telephone number

HAAD Poison and Drug Information Center UAE, TOLL FREE TEL. NUMBER 800-424

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification (CLP):
The substance or mixture is not hazardous according to Regulation (EC) No 1272/2008 (CLP).

2.2. Label elements

Label elements (CLP):

The substance or mixture is not hazardous according to Regulation (EC) No 1272/2008 (CLP).

Supplemental information Contains: 1,2-Benzisothiazol-3(2H)-one May produce an allergic reaction.

Precautionary statement: P262 Do not get in eyes, on skin, or on clothing.

Prevention

2.3. Other hazards

None if used properly.
Not fulfilling Persistent, Bioaccumulative and Toxic (PBT), very Persistent and very Bioaccumulative (vPvB) criteria.
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 2 of 12

SECTION 3: Composition/information on ingredients

3.2. Mixtures

General chemical description:

Bituminous product
Base substances of preparation:
Bitumen

Declaration of the ingredients according to CLP (EC) No 1272/2008:

Hazardous components EC Number content Classification

CAS-No.
4-Nonylphenol, branched, ethoxylated, 0,1- < 1 % Aquatic Chronic 3
>30EO H412
127087-87-0 Eye Irrit. 2
H319
=====
EU. REACH Candidate List of Substances of
Very High Concern for Authorization
(SVHC)
1,2-Benzisothiazol-3(2H)-one 220-120-9 50- < 500 PPM Aquatic Acute 1
2634-33-5 H400
Aquatic Chronic 2
H411
Acute Tox. 4; Oral
H302
Skin Irrit. 2
H315
Skin Sens. 1
H317
Eye Dam. 1
H318
Acute Tox. 2; Inhalation
H330

For full text of the H - statements and other abbreviations see section 16 "Other information".
Substances without classification may have community workplace exposure limits available.

SECTION 4: First aid measures

4.1. Description of first aid measures

General information:
In case of adverse health effects seek medical advice.

Inhalation:
Move to fresh air, consult doctor if complaint persists.

Skin contact:
Rinse with running water and soap. Apply replenishing cream. Change all contaminated clothing.

Eye contact:
Rinse immediately with plenty of running water, seek medical advice if necessary.

Ingestion:
Rinse mouth and throat. Drink 1-2 glasses of water. Seek medical advice.

4.2. Most important symptoms and effects, both acute and delayed
No data available.
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 3 of 12

4.3. Indication of any immediate medical attention and special treatment needed
See section: Description of first aid measures

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media:
carbon dioxide, foam, powder, water spray jet, fine water spray

Extinguishing media which must not be used for safety reasons:

High pressure waterjet

5.2. Special hazards arising from the substance or mixture

In the event of a fire, carbon monoxide (CO) and carbon dioxide (CO2) can be released.
5.3. Advice for firefighters
Wear self-contained breathing apparatus.
Wear protective equipment.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Wear protective equipment.
Avoid contact with skin and eyes.
Danger of slipping on spilled product.

6.2. Environmental precautions

Do not empty into drains / surface water / ground water.

6.3. Methods and material for containment and cleaning up

Remove with liquid-absorbing material (sand, peat, sawdust).
Dispose of contaminated material as waste according to Section 13.

6.4. Reference to other sections

See advice in section 8

SECTION 7: Handling and storage

7.1. Precautions for safe handling
Avoid skin and eye contact.

Hygiene measures:
Wash hands before work breaks and after finishing work.
Do not eat, drink or smoke while working.

7.2. Conditions for safe storage, including any incompatibilities

Do not store together with food or other consumables (coffee, tea, tobacco, etc.).

7.3. Specific end use(s)

Bituminous product
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 4 of 12

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational Exposure Limits

Valid for
Utd.Arab.Emir.

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 0,5 Time Weighted Average AD TLV
8052-42-4 (TWA):
[ASPHALT (BITUMEN) FUME AS
BENZENE-SOLUBLE AEROSOL,
INHALABLE FRACTION OF THE
AEROSOL]
Asphalt 5 Time Weighted Average DB OEL
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Time Weighted Average GCC TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Time Weighted Average UAE OEL
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 5 of 12

Occupational Exposure Limits

Valid for
Bharain

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time Weighted Average BH TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Time Weighted Average GCC TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]

Occupational Exposure Limits

Valid for
Egypt

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 0,5 Time Weighted Average EG OEL
8052-42-4 (TWA):
[ASPHALT (PETROLEUM) FUMES ( AS
BENZENE SOLUBLE AEROSOLS)]

Occupational Exposure Limits

Valid for
Jordan

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time Weighted Average JO TLV
8052-42-4 (TWA):
[ASPHALT]

Occupational Exposure Limits

Valid for
Kuwait

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time Weighted Average GCC TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Short-term Exposure Limit KW OEL
8052-42-4 (STEL):
[ASPHALT (FUME)]
Asphalt Harmful Concentration for Unknown KW OEL
8052-42-4 risk to health and life:
[ASPHALT (FUME)]

Occupational Exposure Limits

Valid for
Israel

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 0,5 Time Weighted Average IL OEL
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 6 of 12

8052-42-4 (TWA):
[ASPHALT (BITUMEN) FUME, AS
BENZENE-SOLUBLE AEROSOL,
INHALABLE FRACTION]

Occupational Exposure Limits

Valid for
Kenya

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time-weighted average KE OEL-RL
8052-42-4 (TWA) OEL-RL:
[ASPHALT, PETROLEUM FUMES]
Asphalt 10 Short-term OEL-RL: KE OEL-RL
8052-42-4
[ASPHALT, PETROLEUM FUMES]

Biological Exposure Indices:

None

8.2. Exposure controls:

Respiratory protection:
Ensure adequate ventilation.

Hand protection:
Recommended are gloves made from Nitril rubber ( Material thickness >0,1 mm, Perforation time < 30s).Gloves should be
replaced after each short time contact or contamination. Available at laboratory specialized trade or at pharmacies / chemist's
shops.

Eye protection:
Goggles which can be tightly sealed.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Appearance liquid
dark brown
Odor Characteristic
Odour threshold No data available / Not applicable

pH 9 - 11
(150 °C (302 °F))
Initial boiling point No data available / Not applicable
Flash point Not applicable
Decomposition temperature No data available / Not applicable
Vapour pressure No data available / Not applicable
Density 0,95 - 1,05 g/cm3
(25 °C (77 °F))
Bulk density No data available / Not applicable
Viscosity No data available / Not applicable
Viscosity (kinematic) No data available / Not applicable
Explosive properties No data available / Not applicable
Solubility (qualitative) No data available / Not applicable
Solidification temperature No data available / Not applicable
Melting point No data available / Not applicable
Flammability No data available / Not applicable
Auto-ignition temperature No data available / Not applicable
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 7 of 12

Explosive limits No data available / Not applicable

Partition coefficient: n-octanol/water No data available / Not applicable
Evaporation rate No data available / Not applicable
Vapor density No data available / Not applicable
Solid content 60 - 65 %
(110 °C )
Oxidising properties No data available / Not applicable

9.2. Other information

No data available / Not applicable

SECTION 10: Stability and reactivity

10.1. Reactivity
None if used for intended purpose.

10.2. Chemical stability

Stable under recommended storage conditions.

10.3. Possibility of hazardous reactions

See section reactivity

10.4. Conditions to avoid

None if used for intended purpose.

10.5. Incompatible materials

None if used properly.

10.6. Hazardous decomposition products

None known.

SECTION 11: Toxicological information

11.1. Information on toxicological effects

General toxicological information:

An allergic reaction cannot be excluded after repeated skin contact.

Acute oral toxicity:

Hazardous components Value Value Route of Exposure Species Method

CAS-No. type application time
4-Nonylphenol, branched, LD50 > 2.000 mg/kg oral rat not specified
ethoxylated, >30EO
127087-87-0
1,2-Benzisothiazol-3(2H)- LD50 490 mg/kg oral rat equivalent or similar to OECD
one Guideline 401 (Acute Oral
2634-33-5 Toxicity)

Acute inhalative toxicity:

Hazardous components Value Value Route of Exposure Species Method

CAS-No. type application time
1,2-Benzisothiazol-3(2H)- LC50 0,4 mg/l dust/mist 4h rat OECD Guideline 403 (Acute
one Inhalation Toxicity)
2634-33-5
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 8 of 12

Acute dermal toxicity:

Hazardous components Value Value Route of Exposure Species Method

CAS-No. type application time
1,2-Benzisothiazol-3(2H)- LD50 > 2.000 mg/kg dermal rat OECD Guideline 402 (Acute
one Dermal Toxicity)
2634-33-5

Skin corrosion/irritation:

Hazardous components Result Exposure Species Method

CAS-No. time
1,2-Benzisothiazol-3(2H)- moderately irritating 4h rabbit EPA OPP 81-5 (Acute Dermal
one Irritation)
2634-33-5

Serious eye damage/irritation:

Hazardous components Result Exposure Species Method

CAS-No. time
1,2-Benzisothiazol-3(2H)- corrosive 3h rabbit EPA OPP 81-4 (Acute Eye
one Irritation)
2634-33-5

Respiratory or skin sensitization:

Hazardous components Result Test type Species Method

CAS-No.
1,2-Benzisothiazol-3(2H)- sensitising Guinea pig guinea pig OECD Guideline 406 (Skin
one maximisat Sensitisation)
2634-33-5 ion test
1,2-Benzisothiazol-3(2H)- sensitising Mouse mouse OECD Guideline 429 (Skin
one local Sensitisation: Local Lymph
2634-33-5 lymphnod Node Assay)
e assay
(LLNA)

Germ cell mutagenicity:

Hazardous components Result Type of study / Metabolic Species Method

CAS-No. Route of activation /
administration Exposure time
1,2-Benzisothiazol-3(2H)- negative bacterial reverse with and without OECD Guideline 471
one mutation assay (e.g (Bacterial Reverse Mutation
2634-33-5 Ames test) Assay)
negative mammalian cell with and without OECD Guideline 476 (In vitro
gene mutation assay Mammalian Cell Gene
Mutation Test)
positive in vitro mammalian with and without OECD Guideline 473 (In vitro
without chromosome Mammalian Chromosome
metabolic aberration test Aberration Test)
activation
1,2-Benzisothiazol-3(2H)- negative oral: gavage mouse OECD Guideline 474
one (Mammalian Erythrocyte
2634-33-5 Micronucleus Test)
negative oral: unspecified rat OECD Guideline 486
(Unscheduled DNA Synthesis
(UDS) Test with Mammalian
Liver Cells in vivo)
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 9 of 12

Reproductive toxicity:

Hazardous substances Result / Classification Species Exposure Species Method

CAS-No. time
1,2-Benzisothiazol-3(2H)- NOAEL P = 112 mg/kg Two rat EPA OPPTS 870.3800
one NOAEL F1 = 56,6 mg/kg generation (Reproduction and Fertility
2634-33-5 NOAEL F2 = 56,6 mg/kg study Effects)
oral: feed

Repeated dose toxicity

Hazardous components Result Route of Exposure time / Species Method

CAS-No. application Frequency of
treatment
1,2-Benzisothiazol-3(2H)- NOAEL=150 oral: gavage 28 daysdaily rat OECD Guideline 407
one mg/kg (Repeated Dose 28-Day Oral
2634-33-5 Toxicity in Rodents)
1,2-Benzisothiazol-3(2H)- NOAEL=69 mg/kg oral: feed 90 daysdaily rat EPA OPP 82-1 (90-Day Oral
one Toxicity)
2634-33-5

SECTION 12: Ecological information

General ecological information:
Do not empty into drains, soil or bodies of water.

12.1. Toxicity

Hazardous components Value Value Acute Exposure Species Method

CAS-No. type Toxicity time
Study
4-Nonylphenol, branched, LC50 > 60 mg/l Fish 96 h Pimephales promelas OECD Guideline
ethoxylated, >30EO 203 (Fish, Acute
127087-87-0 Toxicity Test)
4-Nonylphenol, branched, EC50 > 1.000 mg/l Daphnia 48 h Daphnia magna OECD Guideline
ethoxylated, >30EO 202 (Daphnia sp.
127087-87-0 Acute
Immobilisation
Test)
4-Nonylphenol, branched, IC50 > 1.000 - 2.400 mg/l Bacteria 16 h anaerobic bacteria DIN 38412, part 8
ethoxylated, >30EO (Pseudomonas
127087-87-0 Zellvermehrungshe
mm-Test)
1,2-Benzisothiazol-3(2H)-one LC50 2,15 mg/l Fish 96 h Oncorhynchus mykiss OECD Guideline
2634-33-5 203 (Fish, Acute
Toxicity Test)
NOEC 0,21 mg/l Fish 30 d Oncorhynchus mykiss OECD Guideline
215 (Fish, Juvenile
Growth Test)
1,2-Benzisothiazol-3(2H)-one EC50 2,9 mg/l Daphnia 48 h Daphnia magna OECD Guideline
2634-33-5 202 (Daphnia sp.
Acute
Immobilisation
Test)
1,2-Benzisothiazol-3(2H)-one EC50 0,11 mg/l Algae 72 h Pseudokirchneriella subcapitata OECD Guideline
2634-33-5 201 (Alga, Growth
Inhibition Test)
NOEC 0,0403 mg/l Algae 72 h Pseudokirchneriella subcapitata OECD Guideline
201 (Alga, Growth
Inhibition Test)
1,2-Benzisothiazol-3(2H)-one EC50 23 mg/l Bacteria 3h activated sludge of a OECD Guideline
2634-33-5 predominantly domestic sewage 209 (Activated
Sludge, Respiration
Inhibition Test)
1,2-Benzisothiazol-3(2H)-one NOEC 1,2 mg/l chronic 21 d Daphnia magna OECD 211
2634-33-5 Daphnia (Daphnia magna,
Reproduction Test)
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 10 of 12

12.2. Persistence and degradability

Hazardous components Result Route of Degradability Method

CAS-No. application
4-Nonylphenol, branched, not readily biodegradable. aerobic > 0 - < 60 % OECD 301 A - F
ethoxylated, >30EO
127087-87-0
1,2-Benzisothiazol-3(2H)-one Rapidly biodegradable aerobic 80 % OECD Guideline 303 A
2634-33-5 (Simulation TestAerobic Sewage
Treatment. A: Activated Sludge
Units)

12.3. Bioaccumulative potential / 12.4. Mobility in soil

Hazardous components LogPow Bioconcentration Exposure Species Temperature Method

CAS-No. factor (BCF) time
1,2-Benzisothiazol-3(2H)-one 6,62 56 d not specified other guideline:
2634-33-5
1,2-Benzisothiazol-3(2H)-one 0,7 20 °C EU Method A.8 (Partition
2634-33-5 Coefficient)

12.5. Results of PBT and vPvB assessment

Hazardous components PBT/vPvB

CAS-No.
1,2-Benzisothiazol-3(2H)-one Not fulfilling Persistent, Bioaccumulative and Toxic (PBT), very Persistent and very
2634-33-5 Bioaccumulative (vPvB) criteria.

12.6. Other adverse effects

No data available.

SECTION 13: Disposal considerations

13.1. Waste treatment methods
Product disposal:
Dispose of waste and residues in accordance with local authority requirements.

Disposal of uncleaned packages:

Use packages for recycling only when totally empty.

Waste code
170302
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 11 of 12

SECTION 14: Transport information

14.1. UN number

ADR Not dangerous goods

RID Not dangerous goods
ADN Not dangerous goods
IMDG Not dangerous goods
IATA Not dangerous goods

14.2. UN proper shipping name

ADR Not dangerous goods

RID Not dangerous goods
ADN Not dangerous goods
IMDG Not dangerous goods
IATA Not dangerous goods

14.3. Transport hazard class(es)

ADR Not dangerous goods

RID Not dangerous goods
ADN Not dangerous goods
IMDG Not dangerous goods
IATA Not dangerous goods

14.4. Packing group

ADR Not dangerous goods

RID Not dangerous goods
ADN Not dangerous goods
IMDG Not dangerous goods
IATA Not dangerous goods

14.5. Environmental hazards

ADR not applicable

RID not applicable
ADN not applicable
IMDG not applicable
IATA not applicable

14.6. Special precautions for user

ADR not applicable

RID not applicable
ADN not applicable
IMDG not applicable
IATA not applicable

14.7. Transport in bulk according to Annex II of Marpol and the IBC Code

not applicable
Safety Data Sheet according to (EC) No 1907/2006 as amended

SDS No.: 563770 V003.0 POLYCOAT RBE-15 Page 12 of 12

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture

No information available:

15.2. Chemical safety assessment

A chemical safety assessment has not been carried out.

SECTION 16: Other information

The labelling of the product is indicated in Section 2. The full text
of all abbreviations indicated by codes in this safety data sheet are as follows:
H302 Harmful if swallowed.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H319 Causes serious eye irritation.
H330 Fatal if inhaled.
H400 Very toxic to aquatic life.
H411 Toxic to aquatic life with long lasting effects.
H412 Harmful to aquatic life with long lasting effects.

Further information:
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is
intended to describe our products from the point of view of safety requirements and is not intended to guarantee any
particular properties.

This Safety Data Sheet has been generated based on Regulation (EC) No 1907/2006 and it is applicable for Gulf Cooperation
Council (GCC) and Africa only. No warranty or representation of any kind is given as to compliance with any statutory laws
or regulations of any other jurisdiction or territory, including export laws and regulations. Please confirm that the information
provided herein conforms to the substantive export or other law of any other jurisdiction prior to export. Please contact
Henkel Product Safety and Regulatory affairs for additional assistance.

Dear Customer,
Henkel is committed to creating a sustainable future by promoting opportunities along the entire value chain. If you would
like to contribute by switching from a paper to the electronic version of SDS, please contact the local Customer Service
representative. We recommend to use a non-personal email address (e.g. SDS@your_company.com).

Product is intended for professional use.

Relevant changes in this safety data sheet are indicated by vertical lines at the left margin in the body of this document.
Corresponding text is displayed in a different color on shadowed fields.
 MATERIAL SUBMITTAL FORM
196B DESIGN & CONSTRUCTION OF SOUTH BAY
Reference
INFRA WORKS RD196B-RMB-MAT-INF-000054
No.
Rev. No. 0

Originator of
Submittal
RMB CONTRACTING LLC Plot No. and Location Date 17-Mar-24

Item Description Discipline List of Enclosure

General Specifications for Civil Works Dubai Municipality (Tick as Applicable)

Specifications Reference Drainage and Irrigation Department
As attached Infrastructure Prequalification Documents

Architectural Trade License

BOQ Reference
Structural Vendor's Technical Literature

Drawing Reference As attached Mechanical List of Previous Projects Done

POLYCOAT RBE 15 (SBS Modified Bitumen Emulsion) Electrical Compliance Statement Sheet (*)
Material Specified
HVAC Method Statement

Plumbing Previous Test Results

Material Proposed POLYCOAT RBE 15 (SBS Modified Bitumen Emulsion) for Pump Room Works
Finishes Copy of the Related Specifications

Manufacturer/Supplier M/s. Henkel Polypit Industries External Works Sample with Sample Tag(**)

Address of Manufacturer UAE Civil Works Shop Drawings (if applicable)

Contractor Remarks Landscaping Others (specify)

Date Required on Site As per site requirments

Expected Date of Arrival Expected Date of Material

As per site requirments
of Material on Site: Submittal Documents to RE:

*Compliance statement sheet covering each paragraph and subparagraph of the specification and deviations should be clearly marked.
Advantages/disadvantages betweent the specified and proposed to be mentioned. This statement must be attached to the relevant submittal
form.
**Samples should be presented on a sample board suitably identified with labels. Where it is not possible to present a sample on sample
Notes:
board due to size constraints, sample tag should be attached properly. Photos of samples should be be included in the submittal.
All document submissions should be include one Original along with a soft copy in PDF Format with this submission.
When a resubmission is made based on The Engineer's comments, the compliance/reply to each comment should be clearly mentioned point by
point. The specified format should be filled in accordinly and attached to the submittal form.

We certify that the material specified herewith has been reviewed in detail and is in compliance with the contract drawings and
Contractor Statement
specifications except as otherwise stated above.

Contractor's Authorized
Representative Name Hussain Rashid Hourieh (Sr.Project Manager)

Signature and Stamp

ENGINEER’S COMMENTS
Incoming Ref. No. , if applicable (to be filled by RE)

1.The Proposed POLYCOAT RBE 15 (SBS Modified Bitumen Emulsion)material shall fully comply with the project
specifications, Authorities standards/Specification.
2.Upon delivery, Random samples shall be tested at DCL/ independent laboratory as per project specification,
frequency/approved ITP to confirm that all parameters of the materials comply with the required project specifications.
3.The surface on which the waterproofing membrane is to be applied shall be smooth and free of any sharp edges or
protrusions.
4.The minimum overlap should be 150 mm side and end.
5. Application, Storage, transportation, handling, shall be strictly as per project/Authority specifications & requirements
and manufacture instructions.
6.Mock up sample shall be prepared for check & final approval by the engineer.
7.All materials delivered to the site shall be accompanied with the manufacture's QA/QC certificate.
8.Routine QA/AC procedure shall be followed at site.
9. Final approval is subjected to satisfactory tests results, satisfactory work on site and employer approval.
DM Material Submittal Form (As per Contract) Rev 1 190120
 ‫التاريخ‪2022/01/24 :‬م‬
‫املرجع‪11/122/2022 :‬‬

‫املحترمين ‪،،،‬‬ ‫السادة‪ /‬شركة هنيكل بولي للصناعات املحدودة‬

‫السالم عليكم ورحمة هللا وبركاته‬

‫املوضوع‪ :‬طلب تسجيل مورد‬
‫تتقدم بلدية مدينة الشارقة لكم بأطيب التحيات وأرق األمنيات بدوام ّ‬
‫التقدم واالزدهار‪.‬‬ ‫ّ‬
‫بالشارة إلى املوضوع أعاله‪ ،‬وإلى الطلب الوارد إلينا بكتابكم املؤرخ في ‪2021/11/18‬م بشأن التأهيل املسبق لشركتكم‪ ،‬يرجى العلم بأنه‬
‫بعد مراجعة الفريق الفني املختص للطلب املقدم من قبلكم بشأن املوافقة على اعتماد شركتكم كمورد؛ فإنه قد تم اعتماد شركتكم‬
‫كمورد مؤهل لدى بلدية مدينة الشارقة لتوريد املواد الخاصة بأنظمة العزل املائي وكيماويات مواد البناء في مشاريع بلدية مدينة‬
‫الشارقة‪ ،‬علية يرجى مراجعة إدارة العقود واملشتريات ببلدية مدينة الشارقة لتسجيل شركتكم املوقرة‪.‬‬

‫كما يرجى العلم بأن بلدية مدينة الشارقة لن تتحمل مسؤولية أي عواقب تترتب على هذه املوافقة‪ ،‬عليه يجب التحقق من كل تقديم أو‬
‫مقترح ملشروع قبل مباشرة مواصفات كل مشروع‪.‬‬

‫هذا للتكرم بالعلم وإجراءاتكم‪.‬‬

‫ملزيد من االستفسارات‪ ،‬التواصل مع املهندس‪ /‬بالل جوس رقم هاتف (‪ )05516600020‬بإدارة الصرف الصحي‬

‫وتفضلوا بقبول فائق الحترام والتقدير‪،‬‬

‫ع ‪/‬عبيد سعيد الطنيجي‬

‫مديرعام بلدية مدينة الشارقة‬

‫‪-‬‬

‫‪Page 1 of 1‬‬ ‫]‪[Type here‬‬ ‫‪SCM-SUP-DOC-F-11-01‬‬

Please refer attached comment sheet


No objection with source, subject to full compliance with project specifications and requirements.

Subject to comments, refer to attached comment sheet.

30/06/2022

18120-Arabian Ranches III

RECEIVED
28 Jun 2022

By: Aslam ITime: 4:54 pm

 18120-ARABIAN RANCHES III-PH 3B, 3C & 4B EARTHWORKS & 3B, 3C DEEP SERVICES

Contract: LOA-6831 Package No. PH 3B, 3C & 4B EARTHWORKS & 3B, 3C DEEP SERVICES

Material Description. : Polycoat RBE 15 for Storm & Sewerage Manholes Submittal No. : 18120-6831-MAR-IN-0006-Rev.00

Comment no. Consultant Comments Close Out (Y/N)

No objections with source, subject to full compliance with

1 project specifications and DM standards, BOQ and approved
shop drawings.

Materials delivered on site shall be accompanied with

2 compliance certificate and recent test reports.

Materials to be inspected by the Engineer (MIR) prior to use at

3 site. Materials to be used with in the shelf life. Substrates shall be
inspected and approved by the Engineer.

Draft warranty certificate to be provided as per project

4 requirement.

Sampling and testing required for QA/QC verification to an

5 approved 3rd party testing laboratory.

Handling, storage and installation shall be as per manufacturer's

6 recommendations.

Name & Designation: Virgilio Bautista - Material Engineer Signature: Date: 30/06/2022
22-Jun-2022
 Makeen Tower, Level 17
PO Box 989, Abu Dhabi, UAE
Tel: +971 (0)2 499 9999 Web: www.etihadrail.ae

Transmittal Number: S23-IFIA-JBS-CGT-01225

Project Reference: S23

To: CGT-China Railway-Ghantoot Issue Date: 14/06/2020 11:50:56

Transport JV (C0306)
From: JBS-Jacobs Engineering Group Return By Date: -

Issue Reason: IFIA-Issued for Implementation-Action

Summary: C0306-S02-EUT-MT-00014-AA Material Submittal for Rubberised Bitumen Emulsion

(Polycoat RBE 15) for DM-Networks - (Henkel Polybit)
Notes/Instructions:

Attached Documents:

Document Number Rev Title Contract Number Acceptance Code

C0306-S02-EUT-MT- AA Material Submittal for C0306-Package C Design & 02-Accepted with
00014 Rubberised Bitumen Build Comments
Emulsion (Polycoat RBE
15) for DM-Networks -
(Henkel Polybit)

Distribution:

Name Reason Delivery Method

Osmond Ikwueme N - Notification System Notification

Alan Hugh Morris N - Notification System Notification

DCC N - Notification System Notification

DCC1 CGT N - Notification System Notification

DCC1 EGS N - Notification System Notification

DCC2 EGS N - Notification System Notification

DCC3 EGS N - Notification System Notification

DCC3 JBS N - Notification System Notification

DCCJBS C0306 N - Notification System Notification

Riva Esguerra N - Notification System Notification

Page 1 of 2 Transmittal: S23-IFIA-JBS-CGT-01225

 Lic - Ind - ‫رﺧ ﺼ ﺔ ﺻﻨ ﺎ ﻋ ﻴ ﺔ‬

License Details ‫ﺑ ﻴ ﺎ ﻧ ﺎ ت ا ﻟ ﺮﺧ ﺼ ﺔ‬
HENKEL POLYBIT INDUSTRIES ‫ﻫ ﻨﻴ ﻜ ﻞ ﺑﻮ ﱃ ﺑ ﺖ ﻟ ﻠ ﺼ ﻨ ﺎ ﻋ ﺎ ت‬
Trade Name ‫اﻻﺳﻢ اﻟﺘﺠﺎري‬
LIMTED ‫ا ﳌ ﺤ ﺪ ود ة ذ م م‬

Single Person Limited ‫ﴍﻛ ﺔ ا ﻟ ﺸ ﺨ ﺺ ا ﻟ ﻮا ﺣ ﺪ ذ ا ت‬

Legal Type ‫اﻟﺸﻜﻞ اﻟﻘﺎﻧﻮ‬
Company ‫ﻣ ﺴ ﺆ و ﻟ ﻴ ﺔ ﻣ ﺤ ﺪ ود ة‬

License Number LIC-IND-107 ‫رﻗﻢ اﻟﺮﺧﺼﺔ‬

Issue Date 21/4/1995 ‫ﺗﺎرﻳﺦ اﻻﺻﺪار‬

Expiry Date 7/12/2025 ‫ﺗﺎرﻳﺦ اﻻﻧﺘﻬﺎء‬

Registration No 3246 ‫رﻗﻢ اﻟﺴﺠﻞ اﻟﺘﺠﺎري‬

Email polybitpr@henkel.com ‫اﻟﱪﻳﺪ اﻹﻟﻜ ﱰو‬

Mobile Number 0508992003 ‫رﻗﻢ اﻟﻬﺎﺗﻒ اﳌﺘﺤﺮك‬

License Members ‫ا ﻃ ﺮا ف ا ﻟ ﺮﺧ ﺼ ﺔ‬

‫ا ﻟﺤ ﺼ ﺺ‬ ‫ا ﻟ ﺼﻔﺔ‬ ‫ا ﻟﺠ ﻨﺴﻴﺔ‬ ‫ا ﻻﺳ ﻢ‬
Share Role Nationality Name

‫ﻣﺪﻳﺮ‬ ‫ﻫﻮﻟﻨﺪا‬ ‫ﻫﺎرم ﺑﻴ ﱰوس اﻧﻄﻮﻧﻴﻮس ﺑﻴﱰز‬

0%
Manager Netherlands HARM PETRUS ANTONIUS PETERS

‫ﻣﺎ ﻟ ﻚ‬ ‫اﻹﻣﺎرات اﻟﻌﺮﺑﻴﺔ اﳌﺘﺤﺪة‬ ‫ﻫﻨﻴﻜﻞ اﻳﻪ ﺟﻲ آﻧﺪ ﻛﻮ ﻛﻴﻪ ﺟﻲ اﻳﻪ اﻳﻪ‬
100%
Owner United Arab Emirates HENKEL AG AND CO.KGAA

1 of 3
 License Activities ‫ا ﻧ ﺸ ﻄ ﺔ ا ﻟ ﺮﺧ ﺼ ﺔ‬

Caulking Compounds and Similar Manufacturing ‫ﺻﻨﺎﻋﺔ ﻣﺮﻛﺒﺎت اﻟﺴﺪ اﻟﻐ ﺣﺮاري وﻣﺎ ﺎﺛﻠﻬﺎ‬

Detergents & Disinfectants Manufacturing ‫ﺻﻨﺎﻋﺔ اﳌﻨﻈﻔﺎت واﳌﻄﻬﺮات‬

Retail Sale Of Cosmetics ‫ ﺑﺎﻟﺘﺠﺰﺋﺔ‬- ‫ﺑﻴﻊ ﻣﺴﺘﺤﴬات اﻟﺘﺠﻤﻴﻞ‬

Retail sale of Buildings Material ‫ ﺑﺎﻟﺘﺠﺰﺋﺔ‬- ‫ﺑﻴﻊ ﻣﻮاد اﻟﺒﻨﺎء‬

Wholesale of Cleaners and Detergents Trading ‫ ﺑﺎﻟﺠﻤﻠﺔ‬- ‫ﺗﺠﺎرة اﳌﻨﻈﻔﺎت و اﳌﻄﻬﺮات‬

Wholesale of Cosmetics and Trading ‫ ﺑﺎﻟﺠﻤﻠﺔ‬- ‫ﺗﺠﺎرة ﻣﺴﺘﺤﴬات اﻟﺘﺠﻤﻴﻞ‬

Damp proofing and water proofing works Insulation Contracting ‫ﺗﺮﻛﻴﺐ اﳌﻮاد اﻟﻌﺎزﻟﺔ ﰲ اﻹﺑﻨﻴﺔ واﳌﻨﺸﺄت‬

Cements Prepared Additives Manufacturing ‫ﺻﻨﺎﻋﺔ اﻹﺿﺎﻓﺎت اﳌﺤﱠﴬة ﻟﻸﺳﻤﻨﺖ‬

Fire Extinguishing Materials Manufacturing ‫ﺻﻨﺎﻋﺔ ﻣﻮاد إﻃﻔﺎء اﻟﺤﺮﻳﻖ‬

Beauty and Make-Up Preparations Manufacturing ‫ﺻﻨﺎﻋﺔ ﻣﺴﺘﺤﴬات اﻟﺘﺠﻤﻴﻞ واﻟﺘﺰﻳ‬

services and facilities of oil and gas fields of land and sea ‫ﺧﺪﻣﺎت ﺣﻘﻮل وﻣﻨﺸﺄت اﻟﻨﻔﻂ واﻟﻐﺎز اﻟﱪﻳﺔ واﻟﺒﺤﺮﻳﺔ‬

Address Details ‫ﺗﻔ ﺎ ﺻ ﻴﻞ اﻟ ﻌﻨ ﻮ ان‬

Lease Contract No TC - 35117 ‫رﻗﻢ ﻋﻘﺪ اﻻﻳﺠﺎر‬

Property Owner AHMED MOHAMED SALIM ‫ا ﺣ ﻤﺪ ﻣ ﺤ ﻤﺪ ﺳ ﺎ اﳌ ﻠﻴ ﺤ ﻰ آل‬ ‫ﻣﺎﻟﻚ اﻟﻌﻘﺎر‬

ALMELAIHI AL

Region UMM EL THOUB 7 7 ‫ام ا ﻟ ﺜ ﻌﻮب‬ ‫اﳌﻨﻄﻘﺔ‬

Street undefined ‫اﻟﺸﺎرع‬

Note ‫ﻣ ﻼﺣ ﻈ ﺔ‬

This Document is Considered as Commercial Register ‫ﺗ ﻌ ﺘ ﱪ ﻫﺬ ه ا ﻟ ﺮﺧ ﺼ ﺔ ﺜ ﺎ ﺑ ﺔ ﺳ ﺠ ﻞ ﺗ ﺠ ﺎ ري‬

2 of 3
 Print Date 25/11/2024 ‫ﺗ ﺎ رﻳﺦ ا ﻟ ﻄ ﺒ ﺎ ﻋﺔ‬
Payment voucher DED_PV_221124_0049 ‫رﻗ ﻢ إذ ن ا ﻟ ﺪ ﻓ ﻊ‬
No

‫ ﳌ ﺮا ﺟ ﻌ ﺔ ﺻ ﺤ ﺔ ا ﻟﺒ ﻴ ﺎ ﻧ ﺎ ت ا ﻟ ﻮ ا رد ة‬. ‫ﻫﺬ ه وﺛ ﻴﻘ ﺔ إ ﻟ ﻜﱰوﻧ ﻴ ﺔ ﻣ ﻌ ﺘﻤﺪ ة وﺻ ﺎد رة ﺑﺪ ون ﺗ ﻮ ﻗ ﻴ ﻊ ﻣ ﻦ د ا ﺋ ﺮة ا ﻟ ﺘﻨﻤ ﻴ ﺔ اﻻﻗ ﺘ ﺼ ﺎد ﻳ ﺔ ﰲ أ م ا ﻟﻘ ﻴ ﻮ ﻳ ﻦ‬

‫ ﰲ ا ﻟ ﺮﺧ ﺼ ﺔ ﻳ ﺮﺟ ﻰ ﻣ ﺴﺢ رﻣ ﺰ ا ﻻﺳ ﺘ ﺠ ﺎ ﺑ ﺔ ا ﻟ ﴪ ﻳ ﻌ ﺔ‬.
This is a certified e-document issued without signature by the Department of Economic Development in Umm Al
Quwain. Kindly scan the barcode to verify the certificate.

3 of 3
 ‫رخصة تجارية‬
‫‪Commercial License‬‬
‫تفاصيل الرخصة ‪License Details /‬‬
‫‪License No.‬‬ ‫‪833589‬‬ ‫رقم الرخصة‬

‫هنيكل بولي بت للصناعات المحدودة ذ م م ‪ -‬فرع دبي‬ ‫السم التجارى‬

‫‪Trade Name‬‬ ‫‪HENKEL POLYBIT INDUSTRIES LIMTED - DUBAI BRANCH‬‬

‫‪Legal Type‬‬ ‫‪Branch of Company Registered in other emirates‬‬ ‫فرع لشركة مقرها في امارة أخرى‬ ‫الشكل القانونى‬
‫‪Expiry Date‬‬ ‫‪17/04/2025‬‬ ‫تاريخ النتهاء‬ ‫‪Issue Date‬‬ ‫‪18/04/2019‬‬ ‫تاريخ الصدار‬

‫® ‪D&B D-U-N-S‬‬ ‫‪0‬‬ ‫الرقم العالمي‬ ‫‪Main License No.‬‬ ‫‪833589‬‬ ‫رقم الرخصة الم‬
‫‪No.‬‬
‫‪Register No.‬‬ ‫رقم السجل التجارى‬ ‫‪DCCI No.‬‬ ‫‪320020‬‬ ‫عضوية الغرفة‬

‫الطراف ‪License Members /‬‬

‫الحصص ‪Share /‬‬ ‫الصفة ‪Role /‬‬ ‫الجنسية ‪Nationality /‬‬ ‫السم ‪Name /‬‬ ‫رقم الشخص‪No./‬‬

‫‪100.00%‬‬ ‫مالك ‪Co. Owner /‬‬ ‫‪United Arab Emirates /‬‬ ‫هنيكل بولي بت للصناعات المحدودة ذ‪.‬م‪.‬م‬ ‫‪929197‬‬
‫الشركة‬ ‫المارات‬
‫‪HENKEL POLYBIT INDUSTRIES‬‬
‫‪LIMTED‬‬
‫مدير ‪Manager /‬‬ ‫هولندا ‪Netherlands /‬‬ ‫هارم بيتروس انطونيوس بيترز‬ ‫‪878941‬‬
‫‪HARM PETRUS ANTONIUS PETERS‬‬

‫نشاط الرخصة التجارية ‪License Activities /‬‬

‫‪Insulation Contracting‬‬ ‫تركيب المواد العازلة في البنية والمنشآت المدنية‬
‫‪Fire Resistant & Retardant Materials Trading‬‬ ‫تجارة المواد المقاومة والمانعة لنتشار الحريق‬
‫العنوان ‪Address /‬‬
‫‪Phone No‬‬ ‫‪971-6-7670777‬‬ ‫تليفون‬ ‫‪P.O. Box‬‬ ‫‪293‬‬ ‫صندوق بريد‬
‫‪Fax No‬‬ ‫‪971-6-7670197‬‬ ‫فاكس‬ ‫‪Parcel ID‬‬ ‫‪346-465‬‬ ‫رقم القطعة‬
‫‪Mobile No‬‬ ‫‪971-50-8635523‬‬ ‫هاتف متحرك‬ ‫‪polybitpr@henkel.com‬‬ ‫البريد اللكتروني ‪Email /‬‬

‫مكتب رقم ‪ - 300 - 0121‬ملك رسيس للتطوير )ش‪.‬ذ‪.‬م‪.‬م( ‪ -‬بردبي ‪ -‬البرشاء الولى‬

‫الملحظات ‪Remarks /‬‬

‫(التجارة بالجمله فقط)‬

‫‪Print Date‬‬ ‫‪22/03/2024‬‬ ‫‪10:12‬‬ ‫تاريخ الطباعة‬ ‫‪Receipt No.‬‬ ‫‪0‬‬ ‫رقم اليصال‬
‫يمكنك الن تجديد رخصتك التجارية من خلل الرسائل النصية القصيرة‪ ،‬أرسل رقم الرخصة إلى ‪( 6969‬دو‪/‬اتصالت) للحصول‬
‫على اذن الدفع‪.‬‬ ‫‪Get FREE access to‬‬
‫‪Zoho One for the first‬‬
‫‪Now you can renew your trade license by sending a text message )SMS(. Send your trade‬‬ ‫‪year‬‬
‫‪license number to 6969 )Du/ Etisalat( to receive payment voucher.‬‬ ‫احصل على زوهو ون مجانا ‪.‬‬
‫للسنة الولى‬
‫‪Zoho.com/det‬‬

‫وثيقة إلكترونية معتمدة وصادرة بدون توقيع من دائرة القتصاد والسياحة في دبي ‪.‬لمراجعة صحة البيانات الواردة في الرخصة يرجي مسح رمزالستجابة السريعة‬
‫‪this is a certified e-document issued without signature by the department of Economy and Tourism .Kindly Scan the QR Code to‬‬
‫‪Verify the certificate‬‬
‫‪Economic License‬‬ ‫ﺭﺧﺼــﺔ ﺍﻗﺘﺼﺎﺩﻳﺔ‬
‫‪Commercial License‬‬ ‫ﺭﺧـﺼــــــﺔ ﺗﺠﺎﺭﻳﺔ‬
‫‪Emerging Economic Establishment‬‬ ‫ﻣﻨﺸــــﺄﺓ ﺍﻗﺘﺼـــﺎﺩﻳــــﺔ ﻧﺎﺷﺌـــــــﺔ‬

‫‪License No‬‬ ‫‪:‬‬ ‫‪CN-2803442‬‬ ‫‪:‬‬ ‫ﺭﻗﻢ ﺍﻟﺮﺧﺼﺔ‬

‫‪ADCCI No‬‬ ‫‪:‬‬ ‫‪2604043‬‬ ‫‪:‬‬ ‫ﻋﻀﻮﻳﺔ ﺍﻟﻐﺮﻓﺔ‬

‫‪Establishment Card‬‬ ‫‪:‬‬ ‫‪1034660‬‬ ‫ﻭﺯﺍﺭﺓ ﺍﻟﻤﻮﺍﺭﺩ ﺍﻟﺒﺸﺮﻳﺔ ﻭﺍﻟﺘﻮﻃﻴﻦ ‪:‬‬

‫‪MOHRE‬‬ ‫ﺑﻄﺎﻗﺔ ﺍﻟﻤﻨﺸﺄﺓ‬
‫‪Establishment Card‬‬ ‫‪:‬‬ ‫‪600166‬‬ ‫‪:‬‬ ‫ﺍﻟﻬﻴﺌﺔ ﺍﻻﺗﺤﺎﺩﻳﺔ ﻟﻠﻬﻮﻳﺔ‬
‫‪ICA‬‬ ‫ﻭﺍﻟﺠﻨﺴﻴﺔ‪ -‬ﺑﻄﺎﻗﺔ ﺍﻟﻤﻨﺸﺄﺓ‬
‫‪Legal Form‬‬ ‫‪: UAE Branch - Um Al Kwain‬‬ ‫‪ :‬ﻓﺮﻉ ﺍﻣﺎﺭﺍﺗﻴﺔ ‪ -‬ﺍﻡ ﺍﻟﻘﻴﻮﻳﻦ‬ ‫ﺍﻟﺸﻜﻞ ﺍﻟﻘﺎﻧﻮﻧﻲ‬

‫‪ :‬ﻫﻨﻴﻜﻞ ﺑﻮﻟﻲ ﺑﺖ ﻟﻠﺼﻨﺎﻋﺎﺕ ﺍﻟﻤﺤﺪﻭﺩﺓ ﺫ‪.‬ﻡ‪.‬ﻡ ‪ -‬ﻓﺮﻉ ﺃﺑﻮ ﻇﺒﻲ‬ ‫ﺍﻹﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ‬
‫‪Trade Name‬‬ ‫‪: HENKEL POLYBIT INDUSTRIES LIMTED L.L.C - BRANCH OF ABU DHABI‬‬
‫‪Establishment Date‬‬ ‫‪:‬‬ ‫‪19/06/2019‬‬ ‫‪:‬‬ ‫ﺗﺎﺭﻳﺦ ﺗﺄﺳﻴﺲ ﺍﻟﻤﻨﺸﺄﺓ‬
‫‪Issue Date‬‬ ‫‪:‬‬ ‫‪08/05/2024‬‬ ‫‪:‬‬ ‫ﺗﺎﺭﻳﺦ ﺍﻹﺻﺪﺍﺭ‬
‫‪Expiry Date‬‬ ‫‪:‬‬ ‫‪:‬‬ ‫ﺗﺎﺭﻳﺦ ﺍﻹﻧﺘﻬﺎﺀ‬
‫‪18/06/2025‬‬

‫ﺍﻟﺼﻠﺔ‬ ‫ﺍﻟﺠﻨﺴﻴﺔ‬ ‫ﺍﻟﻤﻼﻙ ‪ /‬ﺍﻟﺸﺮﻛﺎﺀ‬ ‫ﺍﻟﺮﻣﺰ‬

‫‪Role‬‬ ‫‪Nationality‬‬ ‫‪Owners / Partners‬‬ ‫‪No.‬‬

‫ﻣﺎﻟﻚ‬ ‫ﺃﻟﻤﺎﻧﻴﺎ‬ ‫ﺷﺮﻛﺔ ﻫﻨﻴﻜﻞ ﻛﻲ ﺟﻲ ﺍﻳﻪ ﺍﻳﻪ‬ ‫‪42385921‬‬

‫‪Owner‬‬ ‫‪Germany‬‬ ‫‪HENKEL KGAA COMPANY‬‬
‫ﻣﺪﻳﺮ‬ ‫ﻫﻮﻟﻨﺪﺍ‬ ‫ﻫﺎﺭﻡ ﺑﻴﺘﺮﻭﺱ ﺍﻧﻄﻮﻧﻴﻮﺱ ﺑﻴﺘﺮﺯ‬ ‫‪42385920‬‬
‫‪Manager‬‬ ‫‪Netherlands‬‬ ‫‪HARM PETRUS ANTONIUS PETERS‬‬
‫‪Economic Activities‬‬ ‫‪:‬‬ ‫‪:‬‬ ‫ﺍﻷﻧﺸﻄﺔ ﺍﻻﻗﺘﺼﺎﺩﻳﺔ‬
‫‪- Retail sale of flammable resistant paint‬‬ ‫‪ -‬ﺑﻴﻊ ﺍﻟﻄﻼﺀﺍﺕ ﻭﺍﻟﺪﻫﺎﻧﺎﺕ ﺍﻟﻤﻘﺎﻭﻣﺔ ﻟﻠﺤﺮﻳﻖ ‪ -‬ﺑﺎﻟﺘﺠﺰﺋﺔ‬
‫‪- Industrial Cooperative Marketing‬‬ ‫‪ -‬ﺗﺴﻮﻳﻖ ﺗﻌﺎﻭﻧﻲ ﺻﻨﺎﻋﻲ‬
‫‪- Retail Sale of Buildings Material‬‬ ‫‪ -‬ﺑﻴﻊ ﻣﻮﺍﺩ ﺍﻟﺒﻨﺎﺀ ‪ -‬ﺑﺎﻟﺘﺠﺰﺋﺔ‬
‫‪- Installation of insulation materials in buildings and facilities‬‬ ‫‪ -‬ﺗﺮﻛﻴﺐ ﺍﻟﻤﻮﺍﺩ ﺍﻟﻌﺎﺯﻟﺔ ﻓﻲ ﺍﻷﺑﻨﻴﺔ ﻭﺍﻟﻤﻨﺸﺂﺕ‬
‫‪Address‬‬ ‫‪:‬‬ ‫ﻣﺼﻔﺢ ﺟﻨﻮﺏ‪ ,‬ﺍﻳﻜﺎﺩ ‪ ,~ : 0 ,3‬ﻣﺒﻨﻰ‪ ,‬ﺍﻟﺴﻴﺪ ﺳﻤﻮ ﺍﻟﺸﻴﺦ ﻣﺤﻤﺪ ﺑﻦ ﺧﻠﻴﻔﺔ ﺑﻦ ﺯﺍﻳﺪ ﻭ ﺍﺧﺮﻳﻦ‬ ‫‪:‬‬ ‫ﺍﻟﻌﻨﻮﺍﻥ‬

‫‪Onwani Address‬‬ ‫‪:‬‬ ‫‪:‬‬ ‫ﺍﻟﻌﻨﻮﺍﻥ ﺍﻟﻤﻮﺣﺪ‬

‫‪Official Email‬‬ ‫‪:‬‬ ‫‪polybitpr@henkel.com‬‬ ‫ﺍﻟﺒﺮﻳﺪ ﺍﻹﻟﻜﺘﺮﻭﻧﻲ ﺍﻟﺮﺳﻤﻲ ‪:‬‬

‫‪Official Mobile‬‬ ‫‪:‬‬ ‫‪+971508635523‬‬ ‫‪:‬‬ ‫ﺭﻗﻢ ﺍﻟﺘﻮﺍﺻﻞ ﺍﻟﺮﺳﻤﻲ‬

‫‪TAHAQAQ‬‬ ‫ﺗﺤﻘﻖ‬

‫‪www.added.gov.ae‬‬
‫ﻭﺛﻴﻘﺔ ﻣﻌﺘﻤﺪﺓ ﻭﺻﺎﺩﺭﺓ ﺑﺪﻭﻥ ﺗﻮﻗﻴﻊ ﺃﻭ ﺧﺘﻢ ﻣﻦ ﺩﺍﺋﺮﺓ ﺍﻟﺘﻨﻤﻴﺔ ﺍﻹﻗﺘﺼﺎﺩﻳﺔ ‪ -‬ﺃﺑﻮﻇﺒﻲ‪ .‬ﻟﻠﺘﺤﻘﻖ ﻣﻦ ﺻﺤﺔ ﺍﻟﺒﻴﺎﻧﺎﺕ ﺍﻟﻮﺍﺭﺩﺓ ﻓﻲ ﺍﻟﺮﺧﺼﺔ ﺑﺮﺟﺎﺀ ﺯﻳﺎﺭﺓ ﺍﻟﻤﻮﻗﻊ ‪www.tamm.abudhabi‬‬
‫‪Approved document issued without signature or stamp by the Department of Economic Development - Abu Dhabi. To verify the license‬‬
‫‪kindly‬‬
 HENKEL
COMPANY
PROFILE
Building on a strong legacy of more than 145 years, Henkel is leading the way to reimagine and improve
life every day, through our innovative and sustainable brands and technologies, with our teams around the
world. Today and for generations to come.
Henkel holds leading positions in both industrial and consumer businesses. Our portfolio includes
well-known hair care products, laundry detergents, fabric softeners as well as adhesives, sealants, and
functional coatings.

Adhesive Technologies is the world’s number one producer in the area of adhesives, sealants and functional
coatings. We enable the transformation of entire industries, giving our customers a competitive advantage
and offering consumers a unique experience. With trusted brands and high-impact solutions based on an
unmatched technology portfolio we are creating value for all our stakeholders.
With our pioneering spirit, our knowledge, our
products and technologies, we want to enrich
and improve the lives of billions of people every
day – and shape a viable future for the next
generations.
Sustainability is thus a central element in our
vision of the future. We want to actively drive
the transformation to a sustainable economy
and society, help protect and regenerate
nature, contribute to strong communities and
strengthen the trust of our stakeholders.
Our 2030+ Sustainability Ambition Framework
sets our long-term objectives in the three
dimensions of Regenerative Planet, Thriving Communities and Trusted Partner and links to our high
aspiration of achieving a “Transformational Impact for the Good of Generations”.
 HENKEL POLYBIT
Henkel Polybit is part of Henkel Adhesive technologies. It is a
leading global provider of high-quality construction chemicals.
Founded in 1995, the company has over 25 years of experience
in developing and manufacturing innovative solutions for the
construction industry. With two manufacturing sites in UAE and
Saudi Arabia, Henkel Polybit serves its local, regional and global
export markets as the partner of choice for stakeholders across
industry segments.
Henkel Polybit products are designed to meet the highest industry
standards, ensuring the safety, durability, and longevity of
buildings and infrastructure.

Waterproofing Concrete Repair

Tiling Flooring

Henkel Polybit's success is based on a combination of technical

expertise, customer focus and innovation. The company's
dedicated team of engineers and scientists is constantly working to
develop new and improved solutions that meet the evolving needs
of the construction industry.
Overall, Henkel Polybit is a trusted and reliable partner for
construction professionals and companies around the world. With
its proven track record of excellence, sustainability and focus on
customer satisfaction, Henkel Polybit remains committed to deliver
state-of-the-art products and solutions in the years to come.

Henkel Polybit Industries Ltd. Henkel Polybit Industries Ltd.

PO Box: 293, Umm Al Quwain, UAE PO Box: 5911, Dammam - Kingdom of Saudi Arabia
Phone: +971 6 76 70 777, Fax: +971 6 76 70 197 Phone: +966 13808 4061, Fax: +966 13812 1164
henkelpolybit@henkel.com, www.henkelpolybit.com polybitdammam@henkel.com
Henkel Polybit Industries Ltd.
PO Box: 293, Umm Al Quwain, UAE
Phone: +971 (6) 76 70 777
Fax: +971 (6) 76 70 197
henkelpolybit@henkel.com

Henkel Polybit Industries Ltd.

PO Box: 5911, Dammam - 31432
Industrial Area - II, Kingdom of Saudi Arabia
Phone: +966 13 808 4061 / 62
Fax: +966 13 812 1164
polybitdammam@henkel.com

www.henkelpolybit.com