ViewSonic VA721-2
ViewSonic VA721-2
ViewSonic VA721-2
Model No. VLCDS 27998-5W
17” Color TFT LCD Display
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright © 2005 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any m eans, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
1. Appropriate Operation
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar
with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is
exposed in such areas as the associated transformer circuits.
Take out the monitor by grasping the cushion. If the monitor is removed by grasping the LCD
panel, that may cause "MURA."
• General Specifications
Test Resolution & Frequency 1280 x 1024 @ 60Hz
Test Image Size Full Size
Contrast and Brightness Controls Factory Default: Contrast = 70%, Brightness =
100%
• Video Interface
Analog Input Connector DB-15 (Analog)
Video Cable Strain Relief Equal to twice the weight of the monitor for five
minutes.
Video Cable Connector DB-15 Pinout Compliant DDC 2B.
Video Signals Video RGB (Analog)
Video Impedance 75 Ohms (Analog)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals TTL
DDC 1/2B Compliant with Revision 1.3
Video Compatibility Shall be compatible with all PC type computers,
Macintosh computers, and after market video
cards.
Resolution Compatibility 640 x 350, 640 x 480, 720 x 400 (640 x 400), 800 x
600, 832 x 624, 1024 x 768, 1280 x 720, 1280 x
1024
Exclusions Not compatible with interlaced video.
• Power Supply
Internal Power Supply Part Number: ADP-40AFB
Input Voltage Range 90 TO 264 VAC
Input Frequency Range 47.5 TO 63 HERTZ
Short Circuit Protection Output can be shorted without damage.
Over Current Protection 4.5 A typical at 12 VDC
Leakage Current 3.5mA (Max) at 254VAC / 60Hz
EFFICIENCY 70 % typical at 115VAC Full Load
Fuse Internal and not user replaceable
Power Dissipation 35 Watts (typ)
Max Input AC Current 1.2 Arms @ 90VAC, 0.8 Arms @180VAC
Primary Presets
Primary Preset 1280 x 1024 @ 60Hz
Panel Characteristics:
• Mechanical
Ergonomics
Tilt Up 20 degrees minimum
Tilt Down -5 degrees
Swivel Right 0 degrees
Swivel Left 0 degrees
Height Adjust 0 mm
Pivot 0 degrees (Clockwise)
• Environmental Conditions
Operating Temperature 0°C to +40°C
Storage Temperature -20°C to +60°C
Operating Relative Humidity 20% to 90% RH Non-Condensing
Storage Relative Humidity 5% to 90% RH Non-Condensing
Operating Altitude 0 to +3,000 meters
Storage Altitude 0 to +12,000 meters
Main Menu
With OnView controls
1:EXIT 2:SELECT
NOTE: All OnView menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to be adjusted, press SorTto scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one shown below
appears.
Contrast
• Adjust your computer's graphic card so that it outputs a video signal 1280 x
1024 @ 60 Hz to the LCD dislay. (Look for instructions on “changing the
refresh rate” in your graphic card's user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION
until the screen image is completely visible. (The black border around the
edge of the screen should barely touch the illuminated “active area” of the
LCD dislay.)
Adjust the menu items shown below by using the up Iand down Jbuttons.
Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal
to eliminate waviness and distortion. Press the [2] button to obtain a sharper
image.
NOTE:
Auto Image Adjust works with most common video cards. If this function
does not work on your LCD display, then lower the video refresh rate to 60
Hz and set the resolution to its pre-set value.
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, pressSorT.
3. When you are finished making all color adjustments, press
button [1] twice.
i Information displays the timing mode (video signal input) coming from the
graphics card in your computer, the LCD model number, the serial number, and
the ViewSonic website URL. See your graphic card's user guide for instructions
on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution
is 1280 x 1024 and the refresh rate is 60 Hertz.
Image Adjust
Image Adjust
H./V. Position
H. Size
Fine Tune
Sharpness
1:EXIT 2:SELECT
1. Outline
1.1 Buttons on the front panel: Power On/Off button, button 2 (ENTER / INPUT SELECT), up arrow
button, down arrow button, button 1 (MENU).
1.2 D-sub 15-pin connector, DVI-I connector and AC-IN jack are located on the back side of the cabinet.
1.3 OSD menu includes the following function;
Auto Image Adjust (only active under analog input)
Contrast/Brightness
Audio Adjust
Color Adjust
Information
Manual Image Adjust
Setup Menu
Memory Recall
1.4 Contrast and Brightness can be directly controlled with UP / DOWN buttons.
2. Connectors
2.1 AC inlet: CEE22 type connector
2.2 Video signal connector for analog input: 15P Mini D-Sub
CN6
10
DB15HD
16 17
1 RV Red Video
2 GV Green Video
3 BV Blue Video
11
12
13
14
15
4 NC None
5 GND Ground (DDC
return)
6 RG Red GND
7 GG Green GND
8 BG Blue GND
9 +5V +5V (for DDC)
10 SG Sync GND
11 NC None
12 SDA DDC Data
13 HS Horizontal Sync
14 VS Vertical Sync
15 SCL DDC Clock
Contrast 70%
Brightness Max.
Ambient 20 +/- 5 °C
Input AC
3.2 POWER
3.2.1 Power supply
Input voltage 100~240Vac
Power frequency 50~60Hz
Input current <1.5Arms@90Vac
Inrush current <0.75Arms@240Vac
90A(Max) at 230Vac(cold start)
Power consumption 50W(typical);40Watts(Max)
Output @0-3.0A load 12Vdc +/-5%
On 45Watts Green
4. SIGNAL CABLE: Signal cable with Mini D-Sub 15P connectors at both ends. Length: 1.8 meter.
Vertical:
Active Time: 1024 lines Blanking Time: 42 lines
Sync Offset: 1 lines Sync Pulse Width: 3 lines
Border: 0 lines Frequency: 60.02 Hz
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+)
______________________________________________________________________
(72-89) Detailed Timing / Descriptor Block 2:
Monitor Name:
VE710s
Time: 09:10:09
Date: Wed Jan 19, 2005
______________________________________________________________________
VIEWSONIC CORPORATION
EDID Version # 1, Revision # 3
DDCTest For: ViewSonic VE710b
______________________________________________________________________
EDID Block 0, Bytes 0-127
128 BYTES OF EDID CODE:
0 1 2 3 4 5 6 7 8
________________________________________9
0 | 00 FF FF FF FF FF FF 00 5A 63
10 | 18 F6 01 01 01 01 01 0F 01 03
20 | 18 22 1B 78 2E 8A 15 A3 58 49
30 | 9D 24 16 50 54 BF EF 80 81 80
40 | 81 40 71 4F 01 01 01 01 01 01
50 | 01 01 01 01 30 2A 00 98 51 00
60 | 2A 40 30 70 13 00 52 0E 11 00
70 | 00 1E 00 00 00 FF 00 41 33 34
80 | 30 35 30 31 30 30 30 30 31 0A
90 | 00 00 00 FD 00 32 4B 1E 50 0E
100 | 00 0A 20 20 20 20 20 20 00 00
110 | 00 FC 00 56 45 37 31 30 62 0A
120 | 20 20 20 20 20 20 00 9E
This section describes the function of the LCD monitor per functional block.
This monitor includes MB board, power board and button board.
6.1 MB BOARD
The MB board is a two-layer, single-landed design with ground and internal planes provided. DC power from
the power board enters the board through a 6P connector. The other connector on the board is for the button board.
The VGA cable is a signal cable that carries the video, sync and DDC signals from the PC VGA adapter. This
system board consists of 4 functional areas: flat panel controller, MCU with flash ROM, and power regulators.
a) Clock Generation:
Crystal Input Clock (TCLK and XTAL). This is the input pair to an internal crystal oscillator and
corresponding logic. A 14.318 MHz crystal is recommended.
c) OSD: The MST8111A has a fully programmable, high-quality OSD controller. The on-chip static
RAM (4096 words by 24 bits) stores the cell map and the cell definitions.
25 P1.7 Key_down
9 P6.3 Key_right
24 P1.6 Key_up
16 P6.2 Key_left
37 P4.1 Key_mute
23 P1.5 Key_select
42 P5.3 LED_red
41 P5.4 LED_green
e) Panel Power Sequencing (VDDCTRL1, 2) (Pin 32, 3): The MTV312 has two dedicated outputs
VDDCTRL1 and 2 ( Pin32 and Pin3) to control LCD power sequencing once data and control signals
are stable.
f) Panel interface (Pin 1~25, Pin75~128) : The MTV312 driver interface is highly programmable. It supports dual bus /
dual port for SXGA drivers.
6.1.2 Power Regulator MC34063A (U6),AIC1739 (Q4): The MC34063A is a monolithic control IC
containing the primary functions required for DC to DC converters. The device consists of an internal temperature
compensated reference, a comparator, and a controlled duty cycle oscillator with an active current
sense circuit. The desired output voltage is determined by the equation, Volt = 1.25 ( 1 + R67 / R66).
In this case, the output voltage is 3.3 Volts. The AIC1563 is a low dropout positive adjustable
regulator with minimum of 1A output current capability, so it is well suited to serve as a 3.3 V or
2.5 V regulator.
6.1.3 Power Regulator MC34063A (U7): The MC34063A is a monolithic control IC containing the
primary functions required for DC to DC converters. The device consists of an internal temperature
compensated reference, a comparator, and a controlled duty cycle oscillator with an active current
sense circuit. The desired output voltage is determined by the equation, Volt = 1.25 ( 1 + R85 / R86).
In this case, the output voltage is 5.0 Volts for panel power.
6.2.2 Power
This is a general purpose AC / DC adapter which converts 90~240 Vac to a stabilized DC voltage: 12
Volts, with a rated output current of 4.16A. The electrical specification is described below.
b) Vertical Position:
Press the [2] button to return to the horizontal position adjustment page.
Press the [1] button to exit the page.
Press the [▲] button to shift the image upward.
Press the [▼] button to shift the image downward.
4) Sharpness Item
Press the [2] button to enter the sharpness adjustment page.
Press the [1] button to exit the page.
Press “[▲]” Button to increase image sharpness.
Press “[▼]“ Button to decrease image sharpness.
Pattern 1 Pattern2
Pattern 3 Pattern4
Pattern 7 Pattern 8
Pattern 9
1. Equipment needed :
- VE710s/b
- PC ( Personal computer )
- LPT cable
- Fixture (LM5ISP)
- Firmware upgrade program
LPT cable
2. Connection :
To PC To monitor
1.7 Installation has finished , press “ Finish “ button , see Fig 1.7 .
Fig. 1.7
8.1. After installation, shortcuts may be found in the settings path or the program menu (default setting); see Fig 2.1.
8.2 The security file is a key to use ISP functions; press the "OK" button. See Fig 2.2.
8.4 Press “ Create Security File “ button to key in Security code . Adjusting bar to decrease speed of IIC bus , See
Fig. 2.4 .
9.1 Select MTV type first , load the binary or intel hex file that you want to program into the MCU , and select
“ AUTO” item , then press “ RUN “ button , see fig3.1
9.2 If user change the MTV type , it must load file again , or the buffer of load file will be cleared .
9.3 CRC ( cyclic redundancy check ) : the host can check CRC register ’s result instead of reading every byte in
flash . The message of Check MCU CRC OK means that the host verify OK for the progress of program .
11.2 Put the monitor in PE bag & seal the with tape . (Figure.2)
Figure.1 Figure.2
(Figure 3) (Figure 4)
QSG Power cord
(Figure 5) (Figure 6)
Figure 7 Figure 8
Figure 9 Figure 10
Figure 11 Figure 12
12.9 Tear off the AL-foil , all cables on M/B & lamp wires . (Figure 13)
12.10 Take off the screws on the PCB holder & remove the PCB holder with the boards . (Figure 14)
Figure 13 Figure 14
Figure 15 Figure 16
12.13 Put the PCB holder up-side-down & remove the screws on the power board (Figure 17)
12.14 Remove the power board (Figure 18)
Figure 17 Figure 18
12.15 Separate the bezel & panel (with BKT) & remove the cable on panel (Figure 19)
12.16 Take off the L/R BKT & remove the L/R BKT . (Figure 20)
Figure 19 Figure 20
1. No Power
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by
DDC-SCL
DDC-SDA
Triple ADC
Analog
RGB AR , AG, AB Interface
MST8111A
61
LVDS1+ / LVDS1-
Crystal Panel
Clock LVDS2+ / LVDS2- 17” Panel
Gen. Backlight
14.318MHz Interface
CLK+ / CLK-
SCL/SDA
Panel
EEPROM Interface
24C08 Host
RST Control
Interface
ViewSonic Corporation
CPU IRQ
ISP MTV312V64 5V Switch
9. Block Diagram
CSZ Si2301DS
12V
MC34063
MC34063
AIC1739
5V
12V
3.3V
2.5V
+3.3V+2.5V
LVDS
SCALAR QDI LCD
MST8111A +5.0V PANEL(17
LVDS)
ANALOG RGB
PC LCDVCC
VGA POWER
LCDPWR_ON5.0V
+3.3V
EEPROM +3.3V
24LC16
MICRO-CONTROLLER
MTV312
DDC
AUDIO_VOLUME
BRIGHTNESS
AUDIO_MUTE
INVCTRL
34063 +5.0V
ViewSonic Corporation
Model
Title
Date Rev:
16
11 1 RED+IN 2 1 C3 0.047u/6
6 RED-IN SOT23 RED-IN 75/6/F NC R3 68/6
RED- 4
DDC-SDA 12 2 GREEN+IN
7 GREEN-IN
IN-H 13 3 BLUE+IN L3 FCM 1608C-300T06 (BULL WILL) C4 0.047u/6
8 BLUE-IN DSUB_5V GREEN+IN R4 33/6
GREEN+ 4
IN-V 14 4 L35 0/6 C5
9 DSUB_5V_O R5
DDC-SCL 15 5
10 VGA_CON_O L36 100/6/NC C6 0.047u/6
VGA_CON 5
GREEN-IN 75/6/F NC R6 68/6
GREEN- 4
QBHF2!WHB VGA/NC
17
JOQVU VGA_SCL_O L5 100/6
SCL-VGA 5
C7 0.01U/6
R7 100/6
SOGIN 4
D2 D3 D4
DAN217K/NC DAN217K/NC DAN217K/NC C12
RED+IN 3 GREEN+IN 3 BLUE+IN 3 IN-V R13 100/6 DDC_VS R14 100/6 VSYNC
VSYNC 4
0.1U/6/NC R15 C13
2K/6 33P/6
R107 R16 R17
2
U1 2K/6/NC
2K/6/NC 2K/6/NC
1 NC VCC 8
IN-H IN-V VGA_SDA_O VGA_SCL_O VGA_CON_O 2 7 DDC_VS
NC VCLK DDC_VS 5
3 6 SCL-VGA
NC SCK
4 5 SDA-VGA
VSS SDA
1
1
D5 D6 D7 D8 24LC21/NC
Z5.6/NC Z5.6/NC Z5.6/NC Z5.6/NC VDD3V3
1
D32 D9 D10 VCC-DDC
R109
2
2
BAT54C-GS08/NC
C14
CN3
25 0.1U/6/NC
1 TX2- TX2- 4
RX2-
2 TX2+ TX2+ 4
RX2+
GND 3
1
R20 R21
RX4- 4 U2
D12 D13 2K/6/NC 2K/6/NC
RX4+ 5
6 SCL-DDDC 1 NC VCC 8
SCL Z5.6/NC Z5.6/NC 2 7
7 SDA-DDDC NC VCLK
SDA 3 6 R22 100/6/NC SCL-DDDC
VS 8 NC SCK
4 5 SDA-DDDC
2
1
GND
1
RX3- 12
D14 D15 D16 D17
RX3+ 13
14 VCC-DDC
5V Z5.6/NC Z5.6/NC Z5.6/NS Z5.6/NS
GND 15
16 R24 10K/6NC
HP
2
R25 10K/6NC
2
HP-MCU 5
17 TX0- TX0- 4
RX0-
18 TX0+ TX0+ 4
RX0+
GND 19
RX5- 20
RX5+ 21
GND 22
23 TXC+ TXC+ 4
RXC+
24 TXC- TXC- 4
RXC-
ViewSonic Corporation
1
D18 C15
1
C16 0.1U/6NC
1U/6NC Z5.6/NC D19 D20 D21 D22 R26 Model VGA AND DVI INPUT
26 Z5.6/NC Z5.6/NC Z5.6/NC Z5.6/NC 10K/6NC
2
Title
2
VDD3V3 VPO
L8
104
114
126
117
CX601T02001/8
55
65
35
45
51
53
11
21
84
94
18
87
97
U3 C17 C18 C19 C20 C21 C22 C23 C24
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD_MPLL
AVDD_PLL
AVDD
AVDD
VDDC
VDDC
VDDC
VDDC
AVDD_DVI
AVDD_DVI
106 LVACKP 6 22U 0.1U/6 0.1U/6 0.1U/6 0.1U/6 0.1U/6 0.1U/6 0.1U/6
RA0P
RA0N 107 LVACKM 6
3 RED+ 63 108 PA2 FB2P 6
RIN0 RA1P PA3
3 RED- 62 RIN0M RA1N 109 FB2N 6
60 110 PA4 FB1P 6
3 GREEN+ GIN0 RA2P
59 111 PA5 FB1N 6
3 GREEN- GIN0M RA2N PA6
3 SOGIN 61 SOGIN0 RA3P 112 FB0P 6
58 113 PA7 FB0N 6
3 BLUE+ BIN0 RA3N
3 BLUE- 57 BIN0M
3 HSYNC 37 HSYNC0
38 98 PA10 FG2P 6 VDD3V3 VAD VDD3V3 VPLL
3 VSYNC VSYNC0 GA1P
29 99 PA11 FG2N 6 L9 L10
DDC1_CLK/GPO8 GA1N PA12
28 DDC1_DAT/GPO7 GA2P 100 FG1P 6
101 PA13 FG1N 6 CX601T02001/8 CX601T02001/8
GA2N PA14 C25 C26 C27 C28 C29
GA3P 102 FG0P 6
103 PA15 FG0N 6
GA3N 22U 0.1U/6 0.1U/6 22U 0.1U/6
3 TX2+ 40 R+
3 TX2- 41 R-
43 88 PA18 FR2P 6
3 TX1+ G+ BA1P
44 89 PA19 FR2N 6
3 TX1- G- BA1N
46 90 PA20 FR1P 6
3 TX0+ B+ BA2P
47 91 PA21 FR1N 6
3 TX0- B- BA2N
49 92 PA22 FR0P 6
3 TXC+ CK+ BA3P
50 93 PA23 FR0N 6
3 TXC- CK- BA3N
R27 390/1% 52 118 PA24 FCLKP 6 VDD3V3 VDVI VDD3V3 VDPLL
VDVI REXT CLKAP
119 PA25 FCLKN 6 L11 L12
CLKAN
CX601T02001/8 CX601T02001/8
C30 C31 C32 C33 C34
66 16 PB2 BB0N 6
C35 REFP RB1P PB3 22U 0.1U/6 0.1U/6 22U 0.1U/6
MST8111A RB1N 17
22 PB4
BB0P
BB1N
6
6
0.1U/6 Dual Input RB2P PB5
67 REFM RB2N 23 BB1P 6
24 PB6 BB2N 6
RB3P PB7
RB3N 25 BB2P 6
GB0P 6
GB0N 7
8 PB10 BG0N 6
GB1P PB11
GB1N 9 BG0P 6
5 CSZ 69 12 PB12 BG1N 6 VDD2V5 VDD
R28 100/6 CSZ GB2P PB13 L13
71 SCL GB2N 13 BG1P 6
5 SCL R29 100/6 70 14 PB14
5 SDA SDA GB3P BG2N 6
5 RESET 32 15 PB15 BG2P 6 0/8
R51 22/6 HWRESETZ GB3N C36 C37 C38 C39 C40
5 INT 72 INT BB0P 122 LVB2P 6
30 DDCROM_CLK/GPO6 BB0N 123 LVB2M 6
1
C96 C97 31 124 PB18 BR0N 6 22U 0.1U/6 0.1U/6 0.1U/6 0.1U/6
DDCROM_DAT/GPO5 BB1P
1
BB2N 1 BR1P 6
10K/NC PB22
2
BB3P 4 BR2N 6
73 5 PB23 BR2P 6
5 BRIGHTNESS PWM0 BB3N
74 120 PB24 BCLKN 6
PWM1 CLKBP PB25
CLKBN 121 BCLKP 6
C41
2 1 33 75 ESP R30 22/6/NC
XIN ESP OSP R31 22/6/NC
OSP 76 FXDIO 6
22P/6 X1 77
EINV OINV R32 NC
OINV 78 BXDIO 6
C42 14.318MHz
2 1 34 83 GPO0 R33 22/6/NC POL 6
XOUT GPO0 GPO1 R34 22/6/NC
GPO1 82 XSTB 6
22P/6 81 GPO2 YDIO 6
5 XTAL C43 0.1U/6 GPO2 GPO3
3 BYPASS GPO3 80 YCLK 6
2 79 GPO4 YOE 6
AVSS_LPLL GPO4
AVSS_MPLL
AVSS_PLL
AVSS_DVI
AVSS_DVI
AVSS_DVI
GNDC
GNDC
GNDC
GNDC
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
AVSS
AVSS
AVSS
ViewSonic Corporation
105
115
127
116
68
56
64
36
54
39
42
48
10
20
85
95
19
86
96
Date Rev:
1
1 2
GND
MCP810M3X-2.93 VCC RESET R37 R38 R39 R40 R99 R100 R101 R105 R106
G Q1
1
3 VDD3V3 10K/6 MMST3906 10K/6
NC C44 R35 R36 33K/6 33K/6 33K/6 33K/6 33K/6 33K/6/NC
33K/1K/6/NC
3
LED_G CN4
2
1 2
1
2 1 VCPU 0.1U/6 U4 Q2 PWR L37 1K/6 PWR_O
R V
2
1 2
C45 1 8 2K/6 2K/6 R96 4.7K/6 MMST3906 MENU L38 1 2 1K/6 MENU_O 10
A0 VCC R46 100/6 LED_R SEL L39 1K/6 SEL_O 9
2 A1 WP 7 1 2 1 2 8
0.1U/6 SCL_O SCL_1 UP L14 1K/6 UP_O
2
3 A2 SCK 6 1 2
4 5 SDA_O SDA_1 R97 4.7K/6 DOWN L15 1 2 1K/6 DOWN_O 7
R41 82K/6 VSS SI RIGHT L40 1K6/NCRIGHT_O 6 D
1 2
R43 R44 R45 24LC08B R47 100/6 LEFT L41 1 2 1K/6/NCLEFT_O 5
L16 330/6 4
PARAMETER 1 2 3
D23 L17 330/6
EEPROM 1 2 2
VCPU VDD3V3 L18 1 2 0/8
C94
C95
U5 L19 1
1C46
1C47
C92
C93
NC 10K/6 NC
C82
1N4148/NC 7 RST VDD 8 1 2
4 4501-10-10P-R
VDD3
0/8/NC
1
R48 22/6 MH0001 UP R95 C48 C49
4 CSZ 17 P1.0 P1.6 24 TO BUTTON BOARD
0.1U/6
0.1U/6
0.1U/6
R49 22/6 MH0002 DOWN R52 R88
0.1U/6 2
0.1U/6 2
18 25
0.1U/6/NC
0.1U/6/NC
4 SDA P1.1 P1.7
R50 22/6 MH0003 20
4 SCL P1.2 10K/6
PWR 0.1U/6 22U
2
21 P1.3 HCLAMP/DA7 35
1
1
C99 C100 MENU 22 38 10K/6 NC modify debug port
SEL P1.4 HLFHO/DA9
23 P1.5 P5.2/DA2 1 R89 1 100/6 2 PC5V_OFF VDD3V3
0.1u/6/NC 0.1u/6/NC SCL_1 14 34 CN5
P3.5/T1/ISCL P5.6/DA6 VGA_CON 3
R53 2K/6 SDA_1
2
5 DEBUG PORT
2.0mm pitch
VCPU
37 P4.1/HBLANK
NC
NC 6 R42 NC 90° E&T
INVCTRL 36
R58 NC P4.0/VBLANKK RIGHT
VCPU P6.3/AD3 9
16 LEFT
R59 22/6 SS0003 P6.2/AD2 VDD3V3 VDD3V3 VDD3V3 VDD3V3 VDD3V3 VDD3V3 VDD3V3
19 P3.2/INT0 P6.4/DA10 30 HP-MCU 3
4 INT 31
P6.5/DA11 D36 D37 D24 D25 D33 D34 D35
1
15 42 LED_R
P4.2/STOUT P5.3/DA3 LED_G
P5.4/DA4 41
C52 R60 40
P5.5/DA5
2 1 11 X2 HALFV/DA8 39 VCPU 3 RIGHT_O 3 LEFT_O 3 PWR_O 3 MENU_O 3 SEL_O 3 UP_O 3 DOWN_O
R61 10K/6
22P/6 X2 100/6 12 10
C53 11.0592MHz X1 VSS
2 1 DAN217K/NC DAN217K/NC DAN217K DAN217K DAN217K DAN217K DAN217K
2
22P/6 MTV312
C54 0.1U/6/NC
4 XTAL 2 1
1
C55 C57 VCC12 DRIVE SWITCH D26 EC10QS04
8
0.1u/6 0.1u/6 330u/16V/NC 0.3/1206 7 2 PW0006 1 2 R90
1
SENSE EMITTER 10K/6
2
PW0003 6 3 PW0007 R114
VCC TIMING L21 3.3/6
1
DSUB_5V
2
GND C58 C59 5 4 GND
CII GND 47UH
2
VDD3V3 VDD3V3 330U/16V 0.1U/6 CPU VDD3V3 Q11
MC34063
2
1
R64 1 2 VCPU
R65
1
R67 C60 C61 C62 C63
0/6 GND
1
10K/6 2.2K/F/6 470P/6 0.1U/6 330U/16V 330U/16V/NC
1K/6 R68 R91 R92 D30
2
Q3 INVCTRL 3.3V
L22 MMST3906 4.7K/6 2K/6
10K/6
23
R93
2
2 1 GND GND GND GND GND
GND PC5V_OFF 1 22 Q12
2N3904
C101 C64 R69 1K/6
1
VCC12
1U/6 0.1U/6 10K/6/NC
VDD3V3
1
R94
6.8K/6
R70
1K/6 VDD3V3
L23 VDD2V5 PWR_SEL
2
0/6 Q4
1
2 1 R71 10K/6 3 1
VIN VOUT R112
3
C65 2K/6
C68 C69 C70
ViewSonic Corporation
1U/8 Q5 2
SN7002E GND 22U
2
0.1U/6 0.1U/6
2 BRIGHTNESS 4
AIC1739
Model MCU & BUTTOM
1
Title
Date Rev:
2200P/6/NC
11 12
1
R73 C74 C75 0/8/NC FB0N 11 12 FB0P
330U/16V/NC
82K/6/NC
2200P/6/NC
13 13 14 14
GND 15 16 GND R81
R72
C72
C73
FB1N FB1P 3.6K/F/6/NC
2
1 3 17 18
17 18
2
2
FB2N 19 20 FB2P
LVACKM 19 20 LVACKP
4 LVACKM 21 22 LVACKP 4
1
R74 C76 R75 C78 C79 21 22
D 3
FG0N 23 23 24 24 FG0P
C77 25 26 POL
2200P/6 10K/6 0.1U/6 330U/16V GND 25 26 LCDVCC
2
2200P/6 27 27 28 28
82K/6
2
LCDVCC LCDVCC
10K/6/NC
29 29 30 30
G2 1
R76
Q8 S D 3
R82
1841 30P 1.2K/F/6/NC
3
DTC144EUA/NC R77
2 VDDCTRL_1 5 G2 1
82K/6 Q9 S
C 3 GND
3
DTC144EUA GND
1
2 VDDCTRL_2 5
B 2 1 E
C 3
1
CN7 CN8 B 2 1 E
1 1
4 FB0N 2 4 BB2P 2
4 FB0P 3 4 BB2N 3
4 4
4 FB1N 5 4 BB1P 5
4 FB1P 6 4 BB1N 6
7 7 U7
4 FB2N 8 4 BB0P 8
4 FB2P 4 BB0N R83
9 9
10 10 8 DRIVE SWITCH 1
4 FG0N 4 BG2P 0/1206 D29 EC10QS04
11 11
4 FG0P 12 4 BG2N 12 7 SENSE EMITTER 2 1 2
13 13
2
4 FG1N 14 4 BG1P 14 VCC12 6 VCC TIMING 3
4 FG1P 4 BG1N L32
15 15
16 16 5 CII GND 4
1
4 FG2N 4 BG0P C86 47UH GND LCDVCC5
17 17
4 FG2P 18 4 BG0N 18 1U/8 MC34063/NC LCD
19 19 R85 3.6K/F/6
1
4 FCLKN 20 4 BCLKP 20
4 FCLKP 21 4 BCLKN 21
22 22
1
4 FR0N 4 BR2P R86 C87 R87 C88 C89 C90
23 23 GND
4 FR0P 24 4 BR2N 24 1.2K/F/6 470P/6 33K/6 0.01U/6 0.1U/6 330U/16V
25 25
2
4 FR1N 26 4 BR1P 26
4 FR1P 27 4 BR1N 27
28 28
4 FR2N 29 4 BR0P 29
4 FR2P 4 BR0N GND GND GND GND GND GND
30 30 GND
31
4 FXDIO 32
4 XSTB AF730B-A2G1T/NC
33
4 POL 34
4 BXDIO 35
36
4 YCLK 37
4 YDIO 38
4 YOE 39
H3 H4
40
41 2 9 2 9
42 3 8 3 8
LCDVDD L26 0/8/NC 4 1 7 4 1 7
L27 0/8/NC 43
44 5 6 5 6
L28 0/8/NC
L29 0/8/NC 45
MTH276D126 MTH276D126
46
LCDVCC L30 0/8/NC 47
48
H1 H2
49
50 2 9 2 9
ViewSonic Corporation
3 8 3 8
1
4 1 7 4 1 7
1
Title
Date Rev:
SW3
1 2
3 4
5
HDK632A
SW2
A2 green 1 2
3 4
5
C
HDK632A
LED1
EL-209-2EGW A1 orange SW1
1 2
3 4
5
HDK632A
CN1
LED1
ViewSonic Corporation
Model BUTTOM
Title
Date Rev:
Main board
Control board
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices
2. Specification
4. Circuit Description
5. Adjustment Procedure
C. Do you have any other opinions or suggestions regarding this service manual?