DIGITAL HOME THEATER SYSTEM YHT-290/195

AV RECEIVER

RX-V363/HTR-6130 SERVICE MANUAL

YHT-290 consists of HTR-6130 and NS-P270D. (C model)
YHT-195 consists of HTR-6130 and NS-P270D. (R, K, A, L models)
NS-P270D consists of NX-E270, NX-C270 and SW-P270.

RX-V363/HTR-6130
This service manual is for RX-V363/HTR-6130.
For NX-E270, NX-C270 and SW-P270 service manual, please refer to the following service manual:
NX-P270/NX-P276: 101000

IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

■ CONTENTS
TO SERVICE PERSONNEL .......................................... 2 DISPLAY DATA ..................................................... 38–39
FRONT PANELS ........................................................ 3–4 IC DATA ................................................................. 40–55
REAR PANELS .......................................................... 4–9 BLOCK DIAGRAMS .............................................. 56–57
REMOTE CONTROL PANELS ...................................... 9 PRINTED CIRCUIT BOARDS ................................ 58–71
SPECIFICATIONS .................................................. 10–12 PIN CONNECTION DIAGRAMS .................................. 72
INTERNAL VIEW ......................................................... 13 SCHEMATIC DIAGRAMS ...................................... 73–83
DISASSEMBLY PROCEDURES ........................... 14–16 REPLACEMENT PARTS LIST .............................. 85–95
UPDATING FIRMWARE ........................................ 17–19 REMOTE CONTROL .............................................. 96–98
SELF DIAGNOSTIC FUNCTION ........................... 20–37 Advanced setup ........................................................... 99

101084 2008 All rights reserved.

This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'08.02
 RX-V363/HTR-6130

■ TO SERVICE PERSONNEL
1. Critical Components Information AC LEAKAGE
Components having special characteristics are marked s and WALL EQUIPMENT TESTER OR
must be replaced with parts having specifications equal to those OUTLET UNDER TEST EQUIVALENT
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits. INSULATING
TABLE
● Meter impedance should be equivalent to 1500 ohms shunted ● Leakage current must not exceed 0.5mA.
by 0.15µF.
● Be sure to test for leakage with the AC plug in both polarities.

For U model
“CAUTION”
“F2251: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 6A,
125V FUSE.”
RX-V363/HTR-6130

For C model
CAUTION
F2251: REPLACE WITH SAME TYPE 6A, 125V FUSE.
ATTENTION
F2251: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 6A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY
REASON WHAT SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.

About lead free solder

All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder.
Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair
work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)

Caution:
As the melting point temperature of the lead free solder is about 30°C to 40°C (50°F to 70°F) higher than that of the lead solder, be sure
to use a soldering iron suitable to each solder.

2
 RX-V363/HTR-6130

■ SPECIFICATIONS
■ Audio Section
Minimum RMS Output Power (Power Amp. Section) Tone Control Characteristics
(1 kHz, 0.9 % THD) BASS
FRONT L/R, CENTER, SURROUND L/R Boost/Cut ................................................ ±10 dB (100 Hz)
U, C models (8 ohms) ........................................ 100 W/ch TREBLE
Boost/Cut ................................................ ±10 dB (20 kHz)
R, T, K, A, B, G, E, F, L models (6 ohms) ......... 100 W/ch
Filter Characteristics
Maximum Power (JEITA) (1 kHz, 10 % THD)
FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.)
FRONT L/R, CENTER, SURROUND L/R
....... fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct.
U, C models (8 ohms) ........................................ 135 W/ch
SUBWOOFER (L.P.F.)
R, T, K, A, L models (6 ohms) ........................... 135 W/ch ....... fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct.
Max. Power Per Channel [B, G, E, F models]
(1 kHz, 0.7 % THD, 4 ohms)
■ Video Section
FRONT L/R, CENTER, SURROUND L/R .... 105 W or more
RX-V363/HTR-6130

Video Signal Type (Gray back)

IEC Power [B, G, E, F models]
U, C, R, K models ...................................................... NTSC
(1 kHz, 0.1 % THD, 6 ohms)
T, A, B, G, E, F, L models ............................................. PAL
MAIN L/R ........................................................ 90 W or more
Composite Video Signal Level
Dynamic Power Per Channel (IHF) (FRONT L/R)
.................................................................. 1 Vp-p / 75 ohms
U, C models
(8/6/4/2 ohms) .................................... 110/130/160/180 W Component Signal Level
R, T, K, A, B, G, E, F, L models Y ............................................................... 1 Vp-p / 75 ohms
(6/4/2 ohms) .............................................. 105/130/150 W Video Maximum Input Level
Dynamic Headroom .................................................................. 1.5 Vp-p or more
U, C models (8 ohms) ............................................. 0.41 dB Signal to Noise Ratio (IHF)
Input Sensitivity/Input Impedance ....................................................................... 50 dB or more
(1 kHz, 100 W / 6 ohms) Monitor Out Frequency Response
CD, etc. ............................................... 200 mV / 47 k-ohms Component video signal .................. 5 Hz to 60 MHz, -3 dB
MULTI CH INPUT
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER
■ FM Section
........................................................ 200 mV / 47 k-ohms
Maximum Input Signal (1 kHz, 0.5 % THD, Effect on) Tuning Range
CD, etc. .......................................................... 2.0 V or more U, C models ............................................ 87.5 to 107.9 MHz
R, L models ............... 87.5 to 108.0 / 87.50 to 108.00 MHz
Output Level/Output Impedance
T, K, A, B, G, E, F models ................. 87.50 to 108.00 MHz
REC OUT ........................................... 200 mV / 1.2 k-ohms
SUBWOOFER (2 ch STEREO and FRONT SP: Small) 50dB Quieting Sensitivity (IHF) (1 kHz, 100 % Mod.)
................................................................ 4 V / 1.2 k-ohms Mono ......................................................... 2.8 µV (20.2 dBf)

Headphone Jack Rated Output/Impedance Signal to Noise Ratio (IHF)

CD, etc. (1 kHz, 200 mV, 8 ohms) ....... 400 mV / 470 ohms Mono / Stereo ................................................. 73 dB / 70 dB

Frequency Response Harmonic Distortion (1 kHz)

(10 Hz to 100 kHz) Mono / Stereo ................................................. 0.5 % / 0.5 %
CD, etc. to FRONT L/R ..................................... 0 / -3.0 dB Antenna Input .................................... 75 ohms unbalanced
(10 Hz to 20 kHz)
V-AUX to FRONT L/R ....................................... 0 / -3.0 dB
■ AM Section
Total Harmonic Distortion (1 kHz, 50 W)
CD, etc. (2ch stereo) to FRONT L/R SP OUT Tuning Range
U, C models (8 ohms) ................................. 0.06 % or less U, C models .............................................. 530 to 1,710 kHz
R, T, K, A, B, G, E, F, L models (6 ohms) ..... 0.06 % or less R, L models ....................... 530 to 1,710 / 531 to 1,611 kHz
T, K, A, B, G, E, F models ....................... 531 to 1,611 kHz
Signal to Noise Ratio (IHF-A Network)
CD, etc. (STEREO) to Input shorted SP OUT Antenna Input ................................................. Loop antenna
200 mV ........................................................ 98 dB or more
250 mV ...................................................... 100 dB or more
Residual Noise (IHF-A Network)
FRONT L/R SP OUT .................................... 170 µV or less
Channel Separation
CD, etc. (Input 5.1 k-ohms shorted, 1 kHz / 10 kHz)
......................................... 60 dB or more / 45 dB or more
10
 RX-V363/HTR-6130

■ General • SCENE TEMPLATE

Power Supply Program NIGHT Select (Default)

Manufactured under license from Dolby Laboratories.
U, C models ............................................... AC 120 V, 60 Hz SCENE name Contents Source R, T, K, A, B, G,
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Mode Sub-mode Mode U, C models
R, L models .................... AC 110-120/220-240 V, 50/60 Hz Dolby Laboratories. E, F, L models
T model ..................................................... AC 220 V, 50 Hz DVD Viewing DVD Movie DVD STRAIGHT – SYSTEM O (SCENE 1) O
K model ..................................................... AC 220 V, 60 Hz DVD Movie Viewing DVD MOVIE Movie Dramatic SYSTEM O O (SCENE 1)
A model ..................................................... AC 240 V, 50 Hz
DVD Live Viewing Music Live DVD MUSIC Pop/Rock SYSTEM O O
B, G, E, F models ...................................... AC 230 V, 50 Hz “SILENT CINEMA” is a trademark of Yamaha Corporation. DVR Viewing DVR DVR MOVIE Movie Dramatic SYSTEM O O
Power Consumption Music Disc Listening DVD-Audio / Music Disc DVD STEREO 2ch Stereo SYSTEM O O (SCENE 2)
U, C models ................................................ 240 W / 320 VA Disc Listening SA-CD / CD DVD STEREO 5ch Stereo SYSTEM O (SCENE 2) O
R, T, K, A, B, G, E, F, L models ................................ 240 W CD Listening CD Music Disc CD STEREO 5ch Stereo SYSTEM O O
“HDMI”, the “HDMI” logo and “High-Definition Multimedia Interface”
Standby Power Consumption (reference data) are trademarks or registered trademarks of HDMI Licensing LLC. CD Music Listening CD STEREO 2ch Stereo SYSTEM O O
U, C, T, K, A, B, G, E, F models ................................ 0.8 W Radio Listening TUNER/RADIO FM/AM FM/AM
MUSIC ENHANCER Music Enh. 5ch SYSTEM O (SCENE 4) O (SCENE 4)
Maximum Power Consumption (5 ch drive, 10 % THD) (TUNER)
R, L models ............................................................... 530 W “iPod” is a trademark of Apple Inc., registered in the U.S. and other DOCK Listening DAP iPod DOCK
countries. MUSIC ENHANCER Music Enh. 5ch SYSTEM O –
Dimensions (W x H x D) Bluetooth (V-AUX)
......... 435 x 151 x 317.6 mm (17-1/8" x 5-15/16" x 12-1/2") TV Viewing TV DTV/CBL STRAIGHT – SYSTEM O (SCENE 3) O (SCENE 3)
TV Sports Viewing DTV/CBL ENTERTAINMENT TV Sports SYSTEM O O
Weight ................................................. 8.0 kg (17 lbs. 10 oz.)
Bluetooth is a registered trademark of the Bluetooth SIG and is used Game Playing GAME V-AUX ENTERTAINMENT Game SYSTEM O O
Finish by Yamaha in accordance with a license agreement.
[RX-V363]
Gold color ........................................................ T, L models
Black color ..................... U, C, R, A, B, G, E, F, L models • SOUND/SURROUND SELECT MENU
Silver color ................................... R, A, G, E, F, L models “DTS” and “DTS Digital Surround” are registered trademarks of DTS,
Inc. Sound Field Parameters
Titanium color ................................... K, B, G, F, L models
[HTR-6130]
DSP LEVEL MUSIC ENHANCER
Gold color .............................................................. T model
MIN, [MID], MAX LOW, [HIGH]
Black color .............................. U, C, R, A, G, F, L models • DIMENSIONS
STEREO 2ch Stereo
Silver color .......................... U, R, K, A, G, E, F, L models

(7/8")
5ch Stereo

21.7
Accessories ............................................ Remote control x 1
MUSIC Pop/Rock O
Batteries (R03, AAA, UM-4) x 2
Hall O
Indoor FM antenna x 1
Jazz O
AM loop antenna x 1
ENTERTAIN Game O
Optimizer microphone x 1 (R, K, A, B, G, E, F, L models)
TV Sports O

274.9 (10-13/16")
MOVIE Movie Spacious O

317.6 (12-1/2")
230 (9-1/16")
* Specifications are subject to change without notice due to Movie Dramatic O
product improvements. ENHANCER Music Enh. 2ch O
Music Enh. 5ch O
U .......... U.S.A. model B .......... British model
C .......... Canadian model G .......... European model
R .......... General model E .......... South European model Surround Decoders
T .......... Chinese model F .......... Russian model
K .......... Korean model L ........... Singapore model
A .......... Australian model PANORAMA DIMENSION CENTER WIDTH
ON, [OFF] -3, [STD], +3 0, 1, 2, [3], 4, 5, 6, 7
(13/16")

DECODING FORMAT Dolby Digital

21

DTS
POST DECODING FORMAT Dolby Pro Logic
Dolby Pro Logic II Music O O O
151 (5-15/16")
130 (5-1/8")

Dolby Pro Logic II Movie

Dolby Pro Logic II Game
(13/16")

395 (15-9/16")
21

435 (17-1/8")

Unit: mm (inch)

11
12
• SET MENU TABLE

CATEGORY MAIN MENU SUB MENU SELECT MENU VALUE [INITIAL]

BASIC SETUP ROOM :M S / [M] / L
(U, C, T models) SUBWOOFER : YES [YES] / NONE
SPEAKERS : 5 spk 2 spk / 3 spk / 4 spk / [5 spk]
SET / [CANCEL]
RX-V363/HTR-6130

CHECK : Test Tone

CHECK OK? [YES] / NO
SPEAKER LEVEL FL • • • • • || • • • • •
FR • • • • • || • • • • •
C • • • • • || • • • • •
-10 to +10 dB, [0 dB], 1 dB step
SL • • • • • || • • • • •
SR • • • • • || • • • • •
SWFR • • • • • || • • • • •
AUTO SETUP
(R, K, A, B, G, E, F, Use this feature to automatically adjust speaker and system parameters.
L models)
MANUAL SETUP 1 SOUND MENU A) SPEAKER SET FRONT B : FRONT [FRONT] / ZONE B
FRONT : LARGE [LARGE] / SMALL
CENTER : SML NONE / [SML] / LRG
SUR. L/R : SML NONE / [SML] / LRG
BASS OUT : BOTH SWFR / FRNT / [BOTH]
CROSSOVER : 80 Hz 40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz
SWFR PHASE : NRM [NRM] / REV
B) SP LEVEL FL • • • • • || • • • • •
FR • • • • • || • • • • •
C • • • • • || • • • • •
-10 to +10 dB, [0 dB], 1 dB step
SL • • • • • || • • • • •
SR • • • • • || • • • • •
SWFR • • • • • || • • • • •
C) SP DISTANCE UNIT : feet feet (ft) / meters (m)
FRONT L : 10.0 ft
feet : 1.0 to 80.0 ft, [10.0 ft], 0.5 ft step
FRONT R : 10.0 ft
CENTER : 10.0 ft
SUR. L : 10.0 ft feet : 1.0 to 80.0 ft, [8.0 ft], 0.5 ft step
SUR. R : 10.0 ft
SWFR : 10.0 ft feet : 1.0 to 80.0 ft, [10.0 ft], 0.5 ft step
FRONT L : 3.00 m
meters : 0.30 to 24.00 m, [3.00 m], 0.10 m step
FRONT R : 3.00 m
CENTER : 3.00 m
SUR. L : 3.00 m meters : 0.30 to 24.00 m, [2.40 m], 0.10 m step
SUR. R : 3.00 m
SWFR : 3.00 m meters : 0.30 to 24.00 m, [3.00 m], 0.10 m step
D) CENTER GEQ TEST : > OFF ON [OFF] / ON
100 Hz - - || - - 0 dB
300 Hz - - || - - 0 dB
1 kHz - - || - - 0 dB -6.0 to +6.0 dB, [0 dB], 0.5 dB step
3 kHz - - || - - 0 dB
10 kHz - - || - - 0 dB
E) LFE LEVEL SP LFE : 0 dB
-20 to 0 dB, [0 dB], 1 dB step
HP LFE : 0 dB
F) D. RANGE SP D. R. : MAX
MIN / STD / [MAX]
HP D. R. : MAX
G) AUDIO SET MUTE TYP : FULL [FULL] / -20 dB
A. DELAY : 0 ms 0 to 160 ms, [0 ms], 1 ms step
MAX VOL. : +16 dB +16 dB / +10 to -30 dB, [+16 dB], 5 dB step
INI. VOL. : OFF OFF / -80 to +16 dB, [OFF], 1 dB step
2 INPUT MENU A) INPUT ASSIGN IN (1) [COAXIAL] : DVD CD / MD/CD-R / [DVD] / DTV/CBL / V-AUX / DVR
IN (2) [OPTICAL] : CD [CD] / MD/CD-R / DVD / DTV/CBL / V-AUX / DVR
IN (3) [OPTICAL] : DTV/CBL CD / MD/CD-R / DVD / [DTV/CBL] / V-AUX / DVR
B) INPUT RENAME CD / MD/CD-R / DVD / DTV/CBL / V-AUX / DVR
Input is possible to 8 characters
Input possible Character type:
Capital: A to Z, Small: a to z, Figure: 0 to 9, Space, Marks: # * + , - . / : < > ?
C) VOLUME TRIM CD / TUNER / MD/CD-R / DVD / DTV/CBL / V-AUX (DOCK: U, C models) / DVR /
MULTI CH INPUT
-6.0 to +6.0 dB, [0.0 dB], 1.0 dB step
D) DECODER MODE [AUTO] / LAST
CD / DVD / DTV/CBL [AUTO] / DTS
E) MULTI CH SET BGV [LAST] / DVR / V-AUX / DTV/CBL / DVD
3 OPTION MENU A) DISPLAY SET DIMMER :0 -4 to 0, [0], 1 step
B) MEMORY GUARD MEM. GUARD : OFF [OFF] / ON
C) AUDIO SELECT > AUTO LAST [AUTO] / LAST
D) PARAM. INI [NO] / YES
E) BLUETOOTH START PAIRING
(U, C models)
SIGNAL INFO 1 FORMAT (Signal format) Analog / PCM / Dolby Digital / DTS / Digital / --- / ???
2 SAMPLING xxx kHz
3 CHANNEL 2/0/--- / 3/2/0.1 / 1+1/0/--- / ---/---
4 BITRATE (Bit rate) xxx kbps
5 FLAG DTS / Dolby Digital / PCM / None
 RX-V363/HTR-6130

■ INTERNAL VIEW

1 2 3 4 5 6 7 8 1 Power Transformer
2 OPERATION (3) P.C.B.
3 OPERATION (5) P.C.B. (R, L models)
4 MAIN (3) P.C.B.
5 Tuner
6 HDMI P.C.B.
7 OPERATION (4) P.C.B.
8 DSP P.C.B.
9 MAIN (4) P.C.B.
0 MAIN (1) P.C.B.
A OPERATION (2) P.C.B.
B OPERATION (11) P.C.B.
C OPERATION (6) P.C.B.

RX-V363/HTR-6130
D OPERATION (10) P.C.B.
E OPERATION (1) P.C.B.
B A 0 9 F OPERATION (7) P.C.B.

C D E F

13
 RX-V363/HTR-6130

■ DISASSEMBLY PROCEDURES
(Remove parts in the order as numbered.)
Disconnect the power cable from the AC outlet.

1. Removal of Top Cover

a. Remove 4 screws (1), 4 screws (2) and 1 screw (3). (Fig. 1)
b. Slide the top cover rearward to remove it. (Fig. 1)

2. Removal of Front Panel Unit

a. Remove 6 screws (4). (Fig. 1)
b. Remove CB192, CB234, CB261 and CB408. (Fig. 1)
c. Release hook and then remove the front panel unit. (Fig. 1)
RX-V363/HTR-6130

Top cover 3

Front panel unit

2
CB261

4
CB234

CB408
4
CB192
Hook
4

Fig. 1

14
 RX-V363/HTR-6130

3. Removal of HDMI P.C.B.

a. Remove CB904 and CB905. (Fig. 2)
b. Remove 5 screws (5). (Fig. 3)
c. Remove HDMI P.C.B.. (Fig. 2)

4. Removal of OPERATION (4) P.C.B.

a. Remove CB193 and CB182. (Fig. 2)
b. Remove 7 screws (6). (Fig. 3)
c. Remove OPERATION (4) P.C.B.. (Fig. 2)

5. Removal of DSP P.C.B.

RX-V363/HTR-6130
a. Remove 18 screws (7), 3 screws (8) and 2 screws (9) (R, L models). (Fig. 3)
b. Remove cord stopper. (Fig. 2)
c. Remove rear panel. (Fig. 2)
d. Remove screw (0). (Fig. 2)
e. Remove CB512 and CB516. (Fig. 2)
f. Remove the DSP P.C.B. which is connected directly to the MAIN (1) P.C.B. with board-to-board connectors. (Fig. 2)

HDMI P.C.B. OPERATION (4) P.C.B.

Cord stopper Rear panel
CB904 CB905 CB181
CB182 • Board-to-board connectors
DSP P.C.B.
DSP P.C.B. CB502
CB501

CB512

CB516

0
CB193
CB164
CB101
MAIN (1) P.C.B.

Fig. 2

6 5 7

8 9 (R, L models)

Fig. 3
15
 RX-V363/HTR-6130

When checking the P.C.B.

a.Remove the Top cover. (Fig. 1)
b.Remove 3 screws (8). (Fig. 3)
c.Remove 5 screws (A) and 4 screws (B). (Fig. 4)
d.Place the P.C.B.s (with rear panel) upright. (Fig. 5)
e.Connect the ground of heat sink, rear panel and MAIN (1) P.C.B. (G103, G104, G105 and ST101) to the chassis with a
ground lead or the like. (Fig. 5)
• Use the extension cable for connection for the following connectors. (Fig. 6)
DSP P.C.B. CB408 – OPERATION (1) P.C.B. CB202: MF117350 (17P, 300mm)

A B
RX-V363/HTR-6130

A A Ground lead
Rear panel
Fig. 4
MAIN (1) P.C.B.

G104

G103

G105
ST101

Ground lead Chassis

Rear panel
Ground lead

DSP P.C.B.

Fig. 5

CB408

OPERATION (1) P.C.B.

MF117350
CB202

Fig. 6
16
 RX-V363/HTR-6130

■ UPDATING FIRMWARE
After replacing the following parts, be sure to write the latest firmware.
• DSP P.C.B.
• IC201 (DSP P.C.B.)

● Required Tools ● Operation Procedures

• DVD or CD player (with DIGITAL OUTPUT (OPTI- 1. Connect this unit and DVD/CD player as shown be-
CAL or COAXIAL) jack) low. (Fig. 1)
• Optical cable (when OPTICAL jack is used)
• Digital audio pin cable (when COAXIAL jack is used)
• Firmware CD
* To make the firmware CD, download the latest
firmware from the specified download source to
PC.

RX-V363/HTR-6130
Example of connection between digital OPTICAL jacks

This unit

DVD/CD player

Optical cable

Example of connection between digital COAXIAL jacks

This unit

DVD/CD player

Digital audio pin cable

Fig. 1

17
 RX-V363/HTR-6130

2. While simultaneously pressing the “STANDBY/ON” and “SPEAKERS A/B/OFF” keys of this unit, connect the power
cable of this unit to the AC outlet. (Fig. 2)
The FIRMWARE UPDATE mode is activated and “SPDIF Upgrade” is displayed. (Fig. 2)
RX-V363/HTR-6130

"STANDBY/ON" key "SPEAKERS A/B/OFF" key

FIRMWARE UPDATE mode

SPDIF Upgrade

Fig. 2

3. Connect the power cable of DVD/CD player to the AC outlet.

4. Press the “STANDBY/ON” key of the DVD/CD player.
5. Press the “EJECT” key of the DVD/CD player to open the disc tray.
6. Place the firmware CD in the disc tray and close the disc tray.
7. Press the “PLAY” key of the DVD/CD player.
Then writing of the firmware is started. (Fig. 3)
8. When writing of the firmware is completed, “Upgrade OK”, “Please...” and “Turn off!!” are displayed repeatedly. (Fig. 3)

Writing is started. Writing is completed.

Address:XXXXXX Upgrade OK
XXXXXX: Address information of the received data

Please...

Turn off!!

Fig. 3

18
 RX-V363/HTR-6130

* When the version of the firmware to be written is the same as the one existing in this unit, “Same Version”,
“Please...” and “Turn off!!” are displayed repeatedly. (Upgrading is not necessary.)
If the display remains unchanged for more than 10 seconds after starting the firmware CD play procedure, per-
form the firmware CD play procedure again from the beginning.
If “FILE CORRUPTED” is displayed after “Address:XXXXXX”, make sure that the firmware CD is not corrupted
and perform steps 1 to 8 of “Operation Procedures” again.
If “Upgrade Failed” is displayed, perform Steps 1 to 8 of “Operation Procedures” again.

9. Press the “STOP” key of the DVD/CD player.

10. Press the “EJECT” key of the DVD/CD player to open the disc tray.
11. Remove the firmware CD from the disc tray and close the disc tray.
12. Turn off the power of the DVD/CD player and disconnect the power cable from the AC outlet.

RX-V363/HTR-6130
13. Turn off the power by pressing the “STANDBY/ON” key of this unit.

● Confirmation of firmware version and checksum

To confirm that the firmware is updated successfully, check the firmware version and checksum value by using the self-
diagnostic function menu “14. ROM VER/SUM”.
For more information, refer to “SELF DIAGNOSTIC FUNCTION”.
* When the displayed firmware version and checksum are different from written firmware version and checksum, follow
the steps from 1 to 13 of “Operation Procedures” again.

● Initializing of this unit

* After updating the firmware, be sure to initialize this unit.
1. Connect the power cable of this unit to the AC outlet.
2. Press the “STANDBY/ON” key while simultaneously pressing the “STRAIGHT” and “AUDIO SELECT” keys. (Fig. 5)
The self-diagnostic function is activated.
3. Select the main menu “13. FACTORY PRESET”.
4. Select the “PRESET RSRV”.

PRESET INHIBIT (Initialization inhibited) PRESET RESERVED (Initialization reserved)

13.PRESET INHI 13.PRESET RSRV

5. Turn off the power of this unit and disconnect the power cable from the AC outlet.

19
 RX-V363/HTR-6130

■ SELF DIAGNOSTIC FUNCTION

This unit has self diagnosis functions that are intended for inspection, measurement and location of faulty point.
There are 14 main menu items, each of which has sub-menu items.
Listed in the table below are menu items and sub-menu items.
Note that not all menu items listed will apply to the models covered in this service manual.

No. Main menu Sub-menu

1 BYPASS ANALOG BYPASS
DSP BYPASS
2 AUDIO CHECK AUDIO CHECK
MUTE ALL
MUTE SYSTEM IC
MUTE TRUNSISTOR
3 SPEAKERS SET FRNT : SML 0dB
RX-V363/HTR-6130

CENTER : NONE
LFE/B : FRNT
TONE : MAX
TONE : MIN
4 6CH-INPUT 6ch INPUT 6-ohm
6ch INPUT 8-ohm
LIM : , PLDET : , THM :
5 MIC CHECK MIC CHECK
6 FL CHECK VFD CHECK
VFD DISP OFF
VFD DISP ALL
VFD DIMMER
CHECK PATTERN
7 TEST TONE TEST ALL
TEST FRNT L
TEST CENTER
TEST FRNT R
TEST SURR R
TEST SURR L
TEST LFE
8 PROTECTION PRD L : xxx
PRD H : xxx
PRV L : xxx
PRV H : xxx
THM : xxx
PLDET8_L : xxx
PLDET8_H : xxx
PLDET6_L : xxx
PLDET6_H : xxx
PRI : xxx
PDET : xxx
9 AD DATA CHECK PD : xxx PV : xxx
TH : xxx PL : xxx
PI : xxx DE : xxx
K0 : xxx K1 : xxx

20
 RX-V363/HTR-6130

No. Main menu Sub-menu

10 PROTECTION HISTORY History 1
History 2
History 3
History 4
11 iPod DOCK : xxx
DOCK ignore
12 SOFT SW SW MODE

RX-V363/HTR-6130
MODEL
DESTINATION
TUNER DESTINATION
VIDEO FORMAT
AAC
YPAO
RDS
DOCK (iPod)
13 FACTORY PRESET PRESET INHI
PRESET RSRV
14 ROM VER/SUM TOTAL VERSION
CRC14 ALL program
CRC16 apprication & standby (Main program CRC16)
CRC16 SPI F/W update code
CRC16 S/PDIF/ F/W update code
FLASH ROM Read/Write check
SDRAM Read/Write check
EEPROM Read/Write check

21
 RX-V363/HTR-6130

• Starting Self-diagnostic Function

Press the “STANDBY/ON” key while simultaneously pressing those two keys of this unit as indicated in the figure below.

Keys of this unit

Turn on the power while pressing these keys.

RX-V363/HTR-6130

• Starting Self-diagnostic Function in the protection cancel mode

If the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described
below, and it will be possible to enter the self-diagnostic function mode. (The protection functions other than the excess
current detect function will be disabled.)

Press the “STANDBY/ON” key while simultaneously pressing those two keys indicated in the figure above. At this time,
keep pressing those two keys for 3 seconds or longer.
In this mode, the [SLEEP] segment of the FL display of this unit flashes to indicate that the mode is self-diagnostic
function mode with the protection functions disabled.

CAUTION!
Using this product with the protection function disabled may cause damage to this unit. Use special care for this
point when using this mode.

• Canceling Self-diagnostic Function

1. Before canceling self-diagnostic function, execute setting for FACTORY PRESET of main menu No.13 (Memory
initialization inhibited or Memory initialized).
* In order to keep the user memory stored, be sure to select PRESET INHIBITED (Memory initialization inhibited).
2. Turn off the power by pressing the “STANDBY/ON” key of this unit.

• Display provided when Self-diagnostic Function started

On the FL display of this unit, an opening message (including the protection history) appears for a few seconds followed
by the self-diagnostic function menu display (1. ANALOG BYPASS).

22
 RX-V363/HTR-6130

When there is no history of protection function:

When there is no protection history After a few seconds

NO PROTECTION 1.ANLOG BYPASS

When there is a history of protection function due to excess current

PRI PRT:xxx
AD value when the protection function is working

RX-V363/HTR-6130
Cause: An excessive current flowed through the power amplifier.
Supplementary information:
As current of the power amplifier is detected, the abnormal channel can be identified by checking the current
detect transistor.
Turning on the power without correcting the abnormality will cause the protection function to work immediately
and the power supply will instantly be shut off.

Note)
• Applying the power to this unit without correcting the abnormality can be dangerous and cause additional
circuit damage. To avoid this, if “PRI” and “PRD” protection function has been activated 3 times continuously,
the power will not turn on even when the “STANDBY/ON” key is pressed. In order to turn on the power again,
disconnect the power cable of this unit from the AC outlet once and then reconnect it again.
• The output transistors in each amplifier channel should be checked for damage before applying power to this
unit.
• Amplifier current should be monitored by measuring DC voltage across the emitter resistors for each channel.

When there is a history of protection function due to abnormal DC output

PRD PRT:xxx
AD value when the protection function is working

Cause: DC output of the power amplifier is abnormal.

Supplementary information:
The protection function worked due to a DC voltage appearing at the speaker terminal.
A cause could be a defect in the amplifier.
If the power is turned on with the abnormality unsolved, the protection function works in about 3 seconds to turn
off the power.

23
 RX-V363/HTR-6130

When there is a history of protection function due to abnormal voltage in the power supply section

PRV PRT:xxx
AD value when the protection function is working

Cause: The voltage in the power supply section is abnormal.

Supplementary information:
The protection function worked due to a defect or overload in the power supply.
If the power is turned on with the abnormality unsolved, the protection function works in about 1 second to turn
off the power.
RX-V363/HTR-6130

When there is a history of protection function due to excessive heat sink temperature

THM PRT:xxx
AD value when the protection function is working

Cause: The temperature of the heat sink is excessive.

Supplementary information:
The protection function worked due to the temperature limit being exceeded.
Causes could be poor ventilation or a defect related to the thermal sensor.

If the power is turned on with the abnormality unsolved, the protection function works in about 1 second to turn off the power.
For detection of each protection function, refer to main menu described later.

History of protection function

When the protection function has worked, its history is stored in memory with a backup.
Even if no abnormality is noted while servicing the unit, an abnormality which has occurred previously can be
defined as long as the backup data has been stored.
The history of the protection function is cleared when self-diagnostic function is cancelled by selecting PRESET
RESERVED (Memory initialized) of main menu No. 13 or when the backup data is erased.

24
 RX-V363/HTR-6130

• Operation procedure of Main menu and Sub-menu

There are 14 menu items, each of having sub-menu items.
Main menu selection:
Select the menu using “>” (forward) and “<” (reverse) keys of PROGRAM.
Sub-menu selection:
Select the sub-menu using “SCENE 2” (forward) and “SCENE 1” (Reverse) keys.

Keys of this unit

Sub-menu selection

Reverse Forward

RX-V363/HTR-6130
Reverse Forward

Main menu selection

• Functions in Self-Diagnostic Function mode

In addition to the self-diagnostic function menu items, functions as listed below are available.
• Power on/off
• Master volume
• Muting
• Speakers A/B/OFF
• Input selection
• Audio select
• Tone control
* Functions related to the tuner and the set menu are not available.

• Initial settings used to start Self-Diagnostic Function

The following initial settings are used when starting self-diagnostic function.
When self-diagnostic function is canceled, these settings are restored to those before starting self-diagnostic function.
• Master volume: -20 dB
• Input: DVD (MULTI CHANNEL INPUT OFF)
• Effect level: 0 dB
• Main menu: 1. ANALOG BYPASS

25
 RX-V363/HTR-6130

• Details of Self-Diagnostic Function menu

1. BYPASS
Using the sub-menu, it is possible to select ANALOG BYPASS output or DSP BYPASS output.

ANALOG BYPASS
The analog input sound signal is output to FRONT L/R with EFFECT OFF.

1.ANLOG BYPASS

INPUT: DVD ANALOG

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT CENTER SURROUND OUTPUT
Both ch, -20 dBm +6.0 dB +11.5 dBm -∞ -∞ -∞
RX-V363/HTR-6130

DSP BYPASS
The digital input sound signal is output to FRONT L/R with EFFECT OFF.

1.DSP BYPASS
INPUT: DVD ANALOG
SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT CENTER SURROUND OUTPUT
Both ch, -20 dBm +6.0 dB +11.5 dBm -∞ -∞ -∞

2. AUDIO CHECK
The input sound signal is output.
* When the inputted sound signal is 2 ch L/R, it is distributed as follows when output.

L ch: FRONT L, CENTER, SURROUND L,

LFE ( L ch +10 dB)
R ch: SURROUND R

2.AUDIO CHECK

INPUT: DVD ANALOG

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT CENTER SURROUND OUTPUT
Both ch, -20 dBm +6.0 dB +11.5 dBm +11.5 dBm +11.5 dBm 0 dBm

MUTE ALL

2.MUTE ALL

MUTE SYSTEM IC

2.MUTE SYS IC

MUTE TRANSISTOR

2.MUTE TR

26
 RX-V363/HTR-6130

3. SPEAKER SET
The analog switch settings for each sub-menu are as shown in the table below.

FRONT : SML 0dB SMALL LARGE LARGE SWFR

CENTER : NONE LARGE NONE LARGE SWFR
LFE/B : FRNT LARGE SMALL SMALL FRONT
TONE : MAX LARGE LARGE LARGE SWFR
TONE : MIN LARGE LARGE LARGE SWFR

LARGE: This mode is used for a speaker with high bass reproduction performance (a large unit).
Full bandwidth signals are output.
SMALL: This mode is used for a speaker with low bass reproduction performance (a small unit).
The signals of 90 Hz or less are mixed into the channel specified by LFE/BASS.
NONE: This mode is used for no center speaker.

RX-V363/HTR-6130
The center content is reduced by 3 dB and distributed to FRONT L/R.
SWFR: LFE of 5.1 ch signal or LFE/BASS lower than 90 Hz is output through SUBWOOFER OUT.
FRONT: LFE of 5.1 ch signal or LFE/BASS lower than 90 Hz is distributed to FRONT L/R.

FRONT: SML 0dB

3.FRNT:SML 0dB The FRONT L/R signal, when 90 Hz or lower, is mixed to the channel specified by LFE/BASS.

CENTER: NONE
3.CENTER NONE The CENTER signal is distributed to FRONT L/R.

LFE / BASS: FRONT

3.LFE/B:FRNT The LFE (SUBWOOFER) signal is distributed to FRONT L/R.

TONE: MAX
3.TONE:MAX The signal is output with the tone control [BASS +10 dB, TREBLE +10 dB].

TONE: MIN
3.TONE:MIN The signal is output with the tone control [BASS -10 dB, TREBLE -10 dB].

INPUT: DVD ANALOG

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Sub-menu Input level Volume
FRONT CENTER SURROUND OUTPUT
FRONT : SML 0dB Both ch, -20 dBm +6.0 dB +11.5 dBm -∞ -∞ -3.5 dBm
CENTER : NONE Both ch, -20 dBm +6.0 dB +11.5 dBm -∞ -∞ -∞
LFE/B : FRNT Both ch, -20 dBm +6.0 dB +11.5 dBm -∞ -∞ -∞
TONE : MAX Both ch, -20 dBm +6.0 dB +14.5 dBm -∞ -∞ -∞
TONE : MIN Both ch, -20 dBm +6.0 dB +8.5 dBm -∞ -∞ -∞

27
 RX-V363/HTR-6130

4. 6CH INPUT
The input source [MULTI CHANNEL INPUT] is selected.
It is possible to select the 6-ohm/8-ohm by using the sub-menu.

6 ch INPUT 6-ohm

4.6ch INPUT 6 Ω

INPUT: MULTI CH INPUT

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Sub-menu Input level Volume
FRONT CENTER SURROUND OUTPUT
6 ch INPUT 6-ohm Both ch, -20 dBm +6.0 dB +11.5 dBm +11.5 dBm +11.5 dBm -3.5 dBm
RX-V363/HTR-6130

6 ch INPUT 8-ohm

4.6ch INPUT 8 Ω
INPUT: MULTI CH INPUT
SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Sub-menu Input level Volume
FRONT CENTER SURROUND OUTPUT
6 ch INPUT 8-ohm Both ch, -20 dBm +6.0 dB +11.5 dBm +11.5 dBm +11.5 dBm -3.5 dBm

LIM/PLDET/THM
LIM: Setting value of LIM (Limiter control)

* Do not change the setting value because this item is only for the use of development staff.

PLDET: Power limiter detection

The A/D conversion value during operation is displayed.

THM: Thermo protection detection

The A/D conversion value during operation is displayed.
(Reference voltage: 3.3 V=255)

4.255:255: 82
THM (Thermo protection detection)

PLDET (Power limiter detection)

LIM (Limiter control)

5. MIC CHECK
The signals input through the microphone are output of FRONT L/R via A/D and D/A.

5.MIC CHECK

28
 RX-V363/HTR-6130

6. FL CHECK
Use this program to check the FL display section.
For audio signal processing, use STRAIGHT.

Checking FL display section

Initial display

RX-V363/HTR-6130
All segments OFF

All segments ON (dimmer 100%)

All segments ON (dimmer 50%)

Lighting of segments in lattice

29
 RX-V363/HTR-6130

7. TEST TONE
The outputs the noise through the channels specified by the submenu.
The noise frequency for LFE (SUBWOOFER) is 35 to 80 Hz.
Other than that, the noise frequency is 500 to 2 kHz.

TEST ALL
7.TEST ALL Noise is output from all channels.

TEST FRONT L
7.TEST FRNT L Noise is output from the FRONT L channel.
RX-V363/HTR-6130

TEST CENTER
7.TEST CENTER Noise is output from the CENTER channel.

TEST FRONT R
7.TEST FRNT R Noise is output from the FRONT R channel.

TEST SURROUND R
7.TEST SURR R Noise is output from the SURROUND R channel.

TEST SURROUND L
7.TEST SURR L Noise is output from the SURROUND L channel.

TEST LFE (SUBWOOFER)

7.TEST LFE Noise is output from the LFE (SUBWOOFER) channel.

30
 RX-V363/HTR-6130

8. PROTECTION
The A/D setting value of each protection is displayed.
(Reference voltage: 3.3 V=255)

PRD (Amplifier DC protection) Low

8.PRD L : 35 The minimum preset value of PRD is displayed.

PRD (Amplifier DC protection) High

8.PRD H : 81 The maximum preset value of PRD is displayed.

PRV (Voltage protection) Low

8.PRV L : 83 The minimum preset value of PRV is displayed.

RX-V363/HTR-6130
PRV (Voltage protection) High
8.PRV H : 153 The maximum preset value of PRV is displayed.

THM (Thermo protection) High

8.THM : 128 The maximum preset value of THM is displayed.

PLD (PLDET (Power limiter detection)) 8-ohm Low

8.PLD8 L: 77 The value for starting limiter operation of PLD8 is displayed.

PLD (PLDET (Power limiter detection)) 8-ohm High

8.PLD8 H: 100 The value for canceling limiter operation of PLD8 is displayed.

PLD (PLDET (Power limiter detection)) 6-ohm Low

8.PLD6 L: 77 The value for starting limiter operation of PLD6 is displayed.

PLD (PLDET (Power limiter detection)) 6-ohm High

8.PLD6 H: 100 The value for canceling limiter operation of PLD6 is displayed.

PRI (Amplifier current protection) High

8.PRI 100 The maximum preset value of PRI is displayed.

PDET Low
8.PDET 209 The minimum preset value of PDET is displayed.

31
 RX-V363/HTR-6130

9. A/D DATA CHECK

This menu is used to display the A/D conversion value of the microprocessor which detects panel keys of this unit and
protection functions in using the sub-menu.
When K0/K1 menu is selected, keys become non-operable due to detection of the values of all keys. However, it is
possible to advance to the next sub-menu by turning the VOLUME of this unit. When using this function, note that
turning the VOLUME more than 1 click would cause the volume value to change.
Signal processing is maintained in the status before execution.
* The figures in the diagram are given as reference only.

PD/PV
PD: PRD (Power amplifier DC protection detection)
The output of power amplifier DC (DC voltage) is detected.
Normal value: 35 to 81 (Reference voltage: 3.3 V=255)

PV: PRV (Voltage protection detection)

Voltage detects: ACL, AC2, 10V, S9, +12,
-12, +5V and VP
RX-V363/HTR-6130

Normal value: 84 to 153 (Reference voltage: 3.3 V=255)

* If PRD and PRV are out of the normal value range, the protection function works to turn off the power.

PD: 57 PV:128

TH/PL
TH: THM (Thermo protection detection)
The temperature of the heat sink is detected.
Normal value: 0 to 124 (Reference voltage: 3.3 V=255)

* If THM is out of the normal value range, the protection function works to turn off the power.

PL: PLDET (Power limiter detection)

The output voltage of power amplifier is detected.

TH: 77 PL:255

U, C models (Reference voltage: 3.3 V=255)

During normal operation Value for starting limiter operation Value for canceling limiter operation
PLDET 255 77 100
LIM H: 255 / L: 102 H L H
(LIM: Limiter control)

R, T, K, A, B, G, E, F, L models (Reference voltage: 3.3 V=255)

During normal operation Value for starting limiter operation Value for canceling limiter operation
PLDET 255 100 131
LIM H: 255 / L: 90 H L H
(LIM: Limiter control)

PI/DE
PI: PRI (Current protection detection)
The current of the power amplifier is detected.
Normal value: 0 to 100 (Reference voltage: 3.3 V=255)

DE: PDET (Sub-trans power detection)

Normal value: 209 to 255 (Reference voltage: 3.3 V=255)

* If PRI and PDET are out of the normal value range, the protection function works to turn off the power.

PI: 12 DE:255

32
 RX-V363/HTR-6130

K0/K1
K0/K1: KEY0/KEY1 (Panel key of this unit)
The key will fail to function properly if its A/D conversion value deviates more than ±4 from reference value. In
that case, check the constant of partial pressure resistor, solder condition, etc. with referring to the table below.
(Reference voltage: 3.3 V=255)

K0:255 K1:255

Display KEY0 KEY1

23 ± 4 SCENE 1 SCENE 3
42 ± 4 SCENE 2 SCENE 4
66 ± 4 PROGRAM < DIRECT
92 ± 4 PROGRAM > AUDIO SELECT

RX-V363/HTR-6130
120 ± 4 STRAIGHT INPUT <
147 ± 4 TONE CONTROL INPUT >
165 ± 4 SEARCH MODE PRESET/TUNING <
182 ± 4 FM/AM PRESET/TUNING >
198 ± 4 A/B/C/D/E MEMORY
217 ± 4 SPEAKERS TUNING
255 (KEY OFF) (KEY OFF)

10. PROTECTION HISTORY

Four protection histories are displayed.

Example
History 1
10.PRI: 90

Example
History 2
10.PRD: 34

Example
History 3
10.THM: 60

Example
History 4
10.NO PROT

33
 RX-V363/HTR-6130

11. iPod (U, C models)

This menu is used to test the DOCK connector without the iPod itself. After turning off the power to this unit short
between pins No. 14 (TX) and No. 18 (RX), between pins No. 1 (PWR) and No. 17 (ACCPOW) and between pins No. 4
(iPDET) and No. 8 (DGND) of the DOCK connector. (Make sure that the power is turned off when shorting pins.)
Start the self-diagnostic function and select this menu.
The check result is displayed according to the following display specifications.

Note) Be sure to return the shorted pins to their original condition after executing this test.

15 16 17 18

9 10 11 12 13 14
RX-V363/HTR-6130

3 4 5 6 7 8
11.DOCK:NG NNN
1 19 20 21 2 All Y = “OK”
Others = “NG”

DOCK CONNECTOR

Check item Result Display

OK Y 
UART loop back test 
NG N 
High Y 
iPAP (iPod accessory power) detection IC402 pin No. 1 
Low N 
Low (iPod universal dock) Y 
iPDET (iPod installation to DOCK) detection IC402 pin No. 12 
High (Bluetooth adapter) N 

DOCK ignore
When DOCK and iPod are connected, the input source [DOCK (iPod)] is made ineffective and [V-AUX] is selected.

11.DOCK IGNORE

34
 RX-V363/HTR-6130

12. SOFT SW
Note) Do not change the function settings because this menu is only for the use of development staff.

This menu is used to change the function of this unit by switching the function settings on P.C.B. through the software.
* Mentioning the details is not allowed because this menu is only for the use of development staff.

Switch mode
12.MODE:PCB

Model
12.MODEL:363

RX-V363/HTR-6130
Destination
12.DEST : UC

Tuner destination
12.TUNER: UC

VIDEO format
12.VIDEO:NTSC

AAC
12.AAC : NOT

YPAO
12.YPAO : AVAIL

RDS
12.RDS: AVAIL

12.DOCK: NOT DOCK (iPod)

35
 RX-V363/HTR-6130

13. FACTORY PRESET

This menu is used to reserve and inhibit initialization of the back-up RAM.
The signals are processed using EFFECT OFF (The L/R signal is output using ANALOG BYPASS).

PRESET INHIBIT (Initialization inhibited)

13.PRESET INHI
Back-up RAM initialization is not executed. Select this sub-menu to protect the values set by the user.

PRESET RESERVED (Initialization reserved)

13.PRESET RSRV
Initialization of the back-up RAM is reserved. (Actually, initialization is executed the next time that the
power is turned on.)
Select this sub-menu to reset to the original factory settings or to reset the RAM.
Any protection history will be cleared.
RX-V363/HTR-6130

CAUTION: Before setting to the PRESET RESERVED, write down the existing preset memory content of the tuner in a table
as shown below.
(This is because setting to the PRESET RESERVED will cause the user memory content of the tuner to be
erased.)

Preset Group P1 P2 P3 P4 P5 P6 P7 P8
A
B
C
D
E

36
 RX-V363/HTR-6130

14. ROM VER/SUM

The firmware version and checksum values are displayed. The signal is processed using EFFECT OFF.
The checksum is obtained by adding the data at every 8 bits for each program area and expressing the result as a 4-
figure hexadecimal data.

Version
14. VER. C015
Firmware version of microprocessor (IC101 DSP P.C.B.) is displayed.

All checksum
14.A.SUM:6F75
Checksum value of microprocessor (IC101 DSP P.C.B.) is displayed.

RX-V363/HTR-6130
Program checksum
14.P.SUM:D057
Checksum value of application and standby code program is displayed.

SPI (Serial Peripheral Interface) checksum

14.SPI.S:A3F0
Checksum value of SPI firmware update code is displayed.

SPD (S/PDIF) checksum

14.SPD.S:FC4A
Checksum value of SPD firmware update code is displayed.

FlashROM test
FROM TEST:NoEr The read/write test of microprocessor (IC101 DSP P.C.B.) and flash ROM (IC201 DSP P.C.B.).

NoEr: No error detected NG: An error is detected

SDRAM test
DRAM TEST:NoEr The read/write test of microprocessor (IC101 DSP P.C.B.) and SDRAM (IC202 DSP P.C.B.).

NoEr: No error detected NG: An error is detected

EEPROM test
PROM TEST:NoEr The read/write test of microprocessor (IC101 DSP P.C.B.) and EEPROM (IC102 DSP P.C.B.).

NoEr: No error detected NG: An error is detected

37
 RX-V363/HTR-6130

■ DISPLAY DATA
● V2001 : 17-BT-29GNK (OPERATION P.C.B.)
} 1

PATTERN AREA

● PIN CONNECTION

Pin No. 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
RX-V363/HTR-6130

Connection F2 NX NP NP P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31

Pin No. 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection P32 P33 P34 P35 P36 P37 NX NX NX NX NX NX NX 17G 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP NX F1
Note : 1) F1, F2 ..... Filament pin 2) NP ..... No pin 3) NX ..... No extend pin 4) 1G-17G ..... Grid pin

● GRID ASSIGNMENT
17G 16G 15G

1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G

S3 S4 S1

S6 S7 S8 S9 S10 S11 S12 S13 S14

S5

(17G) (16G) (15G)

S15 S2
S16 2f
1b 2b
S18 S19
1g 1a 2a s25 s24
S17 S20 S21
S22 1f 2g s23
1-1 2-1 3-1 4-1 5-1
1e s24 s25

1-2 2-2 3-2 4-2 5-2 1d 2d

1c 2c
1-3 2-3 3-3 4-3 5-3 2e

1-4 2-4 3-4 4-4 5-4

S26
1-5 2-5 3-5 4-5 5-5
S27
1-6 2-6 3-6 4-6 5-6

1-7 2-7 3-7 4-7 5-7

(1G-14G)
38
 RX-V363/HTR-6130

● ANODE CONNECTION
17G 16G 15G 14G 13G-1G
1P S1 S2 1-1 1-1
2P S6 S26 2-1 2-1
3P S7 S27 3-1 3-1
4P S8 S22 4-1 4-1
5P S9 1a 5-1 5-1
6P S10 1b 1-2 1-2
7P S11 1c 2-2 2-2
8P S12 1d 3-2 3-2

RX-V363/HTR-6130
9P 1e 4-2 4-2
10P S20 1f 5-2 5-2
11P 1g 1-3 1-3
12P 2a 2-3 2-3
13P 2b 3-3 3-3
14P 2c 4-3 4-3
15P 2d 5-3 5-3
16P 2e 1-4 1-4
17P 2f 2-4 2-4
18P S21 2g 3-4 3-4
19P S23 4-4 4-4
20P S3 S24 5-4 5-4
21P S5 S25 1-5 1-5
22P S4 2-5 2-5
23P S15 3-5 3-5
24P S16 S13 4-5 4-5
25P S17 S14 5-5 5-5
26P S18 1-6 1-6
27P S19 2-6 2-6
28P 3-6 3-6
29P 4-6 4-6
30P – 5-6 5-6
31P – 1-7 1-7
32P – 2-7 2-7
33P – 3-7 3-7
34P – 4-7 4-7
35P – 5-7 5-7
36P – –
37P – –

39
 RX-V363/HTR-6130

■ IC DATA
IC101: ADSP-BF531 CPU (DSP P.C.B.)
Microprocessor and DSP

JTAG test Event controller/

Core timer Watch dock timer
and emulation

Voltage Real time clock

regulator
UART port IrDA®

L1 order Memory L1 data

RX-V363/HTR-6130

memory management memory

unit
Timer0, Timer1, Timer2

Core/System bus interface

PPI/GPIO

DMA controller
Serial port (2)

SPI port
Boot ROM
External port for flash
and SDRAM control
VDDEXT

VDDEXT

VDDEXT

VDDEXT
CLKOUT

ADDR10
ADDR11
ADDR12
VDDINT

VDDINT

VDDINT
ADDR1
ADDR2
ADDR3
ADDR4

ADDR5
ADDR6
ADDR7
ADDR8
ADDR9
SCKE

SRAS
SCAS

AMS0
AMS1
AMS2
AMS3
ARDY

ABE0
ABE1
SA10
SWE

AWE
GND
GND
GND

GND

GND

GND

GND
SMS

AOE
ARE
BR
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
GND 1 132 GND
GND 2 131 GND
GND 3 130 GND
VROUT2 4 129 GND
VROUT1 5 128 GND
VDDEXT 6 127 ADDR13
GND 7 126 ADDR14
GND 8 125 ADDR15
GND 9 124 ADDR16
CLKIN 10 123 ADDR17
XTAL 11 122 ADDR18
VDDEXT 12 121 ADDR19
RESET 13 120 BGH
NMI 14 119 BG
GND 15 118 VDDEXT
RTXO 16 117 GND
RTXI 17 116 DATA0
VDDRTC 18 115 DATA1
GND 19 114 DATA2
VDDEXT 20 113 DATA3
ADSP-BF531
PPI_CLK 21 112 DATA4
PP10 22 111 VDDINT
PP11 23 110 DATA5
PP12 24 IC101 109 DATA6
VDDINT 25 108 DATA7
PP13 26 107 VDDEXT
PF15 27 106 GND
PF14 28 105 DATA8
PF13 29 104 DATA9
GND 30 103 DATA10
VDDEXT 31 Core Clock = 25M * 16 / 1 102 DATA11
PF12 32 = 400 MHz (Max : 400M) 101 DATA12
PF11 33 100 DATA13
PF10 34 System Clock = 25M * 16 / 3 99 DATA14
PF9 35 = 133 MHz (Max : 133M) 98 DATA15
PF8 36 97 GND
PF7 37 96 BMODE0
PF6 38 95 BMODE1
GND 39 94 TCK
GND 40 93 VDDEXT
GND 41 92 GND
GND 42 91 GND
GND 43 90 GND
GND 44 89 GND
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
VDDEXT
PF5
PF4
PF3
PF2
PF1
PF0
VDDINT
SCK
MISO
MOSI
GND
VDDEXT
DT1SEC
DT1PRI
TFS1
TSCLK1
DR1SEC
DR1PRI
RFS1
RSCLK1
VDDINT
DT0SEC
DT0PRI
TFS0
GND
VDDEXT
TSCKL0
DR0SEC
DR0PRI
RFS0
RSCLK0
TMR2
TMR1
TMR0
VDDINT
TX
RX
EMU
TRST
TMS
TDI
TDO
GND

40
 RX-V363/HTR-6130

Pin No. Port Name Function Name I/O Detail of Function

1 DGND GND – Ground of external
2 DGND GND – Ground of external
3 DGND GND – Ground of external
4 /VINTSW VROUT2 O Voltage regulator drive for Q101
5 /VINTSW VROUT1 O Voltage regulator drive for Q101
6 VDDEXT VDDEXT – I/O power supply (EX3.3)
7 DGND GND – Ground of external
8 DGND GND – Ground of external
9 DGND GND – Ground of external
10 CLKIN CLKIN I Clock/oscillation input
11 XTAL XTAL O Oscillation output
12 VDDEXT VDDEXT – I/O power supply (EX3.3)
13 /DRESET /RESET I Delayed reset

RX-V363/HTR-6130
14 NMI/DGND NMI I (Pull-down)
15 DGND GND – Ground of external
16 – RTXO O
17 RTXI/DGND RTXI I (Pull-down)
18 – VDDRTC –
19 DGND GND – Ground of external
20 VDDEXT VDDEXT – I/O power supply (EX3.3)
21 – PPI_CLK I
22 – PP10 I/O
23 – PP11 I/O
24 – PP12 I/O
25 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
26 – PP13 I/O
27 VIB PF15 O Video select B
28 VIA PF14 O Video select A
29 – PF13 I
30 DGND GND – Ground of external
31 VDDEXT VDDEXT – I/O power supply (EX3.3)
32 /ICXM PF12 O
33 /XMPWR PF11 O
34 INTAK PF10 I CODEC IC (IC301) interrupt
35 FSYNC/TFS0 PF9 I Frame sync detect
36 R2A_DATA PF8 O DATA for R2A volume/selector IC (IC162)
37 R2A_CLK PF7 O CLK for R2A volume/selector IC (IC161)
38 VRB PF6 I Volume rotary B
39 DGND GND – Ground of external
40 DGND GND – Ground of external
41 DGND GND – Ground of external
42 DGND GND – Ground of external
43 DGND GND – Ground of external
44 DGND GND – Ground of external
45 VDDEXT VDDEXT – I/O power supply (EX3.3)
46 VRA PF5 I Volume rotary A
47 REM PF4 I IR remote control pulse input
48 PSW PF3 I Power switch (STANDBY/ON)
49 /SPISEL2 PF2 O CS for EEPROM (IC102)
50 /SPISEL1 PF1 O CS for 4ch ADC (IC401)
51 /EXPE PF0 O Extended port enable
52 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
53 SPISCK SCK I/O SPI clock
54 SPIMI MISO I/O Master input/slave output
55 SPIMO MOSI I/O Master output/slave input
56 DGND GND – Ground of external
57 VDDEXT VDDEXT – I/O power supply (EX3.3)
58 DT1SEC DT1SEC O Serial port 1, secondary transmission data
59 DT1PRI DT1PRI O Serial port 1, primary transmission data
60 TFS1 TFS1 I/O Serial port 1, frame asynchronous transmission

41
 RX-V363/HTR-6130

Pin No. Port Name Function Name I/O Detail of Function

61 TSCLK1 TSCLK1 I/O Serial port 1, serial transmission clock
62 DR1SEC DR1SEC I Serial port 1, secondary reception data
63 DR1PRI DR1PRI I Serial port 1, primary reception data
64 RFS1 RFS1 I/O Serial port 1, frame synchronization reception
65 RSCLK1 RSCLK1 I/O Serial port 1, serial reception clock
66 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
67 DT0SEC DT0SEC O Serial port 0, secondary transmission data
68 DT0PRI DT0PRI O Serial port 0, primary transmission data
69 TFS0 TFS0 I/O Serial port 0, frame asynchronous transmission
70 DGND GND – Ground of external
71 VDDEXT VDDEXT – I/O power supply (EX3.3)
72 TSCLK0 TSCLK0 I/O Serial port 0, serial transmission clock
73 DR0SEC DR0SEC I Serial port 0, secondary reception data
74 DR0PRI DR0PRI I Serial port 0, primary reception data
RX-V363/HTR-6130

75 RFS0 RFS0 I/O Serial port 0, frame synchronization reception

76 RSCLK0 RSCLK0 I/O Serial port 0, serial reception clock
77 – TMR2 I/O
78 – TMR1 I/O
79 LIMITER TMR0 O Limiter control output
80 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
81 DTXM TX O
82 DRXM RX I
83 – /EMU O
84 – /TRST I
85 – TMS I
86 – TDI I
87 – TDO O
88 DGND GND – Ground of external
89 DGND GND – Ground of external
90 DGND GND – Ground of external
91 DGND GND – Ground of external
92 DGND GND – Ground of external
93 VDDEXT VDDEXT – I/O power supply (EX3.3)
94 – TCK I
95 BMODE1 BMODE1 I (Pull-down)
96 BMODE0 BMODE0 I (Pull-up)
97 DGND GND – Ground of external
98 D16 DATA15 I/O SDRAM data bus 16
99 D15 DATA14 I/O SDRAM data bus 15
100 D14 DATA13 I/O SDRAM data bus 14
101 D13 DATA12 I/O SDRAM data bus 13
102 D12 DATA11 I/O SDRAM data bus 12
103 D11 DATA10 I/O SDRAM data bus 11
104 D09 DATA9 I/O SDRAM data bus 09
105 D08 DATA8 I/O SDRAM data bus 08
106 DGND GND – Ground of external
107 VDDEXT VDDEXT – I/O power supply (EX3.3)
108 D07 DATA7 I/O SDRAM data bus 07
109 D06 DATA6 I/O SDRAM data bus 06
110 D05 DATA5 I/O SDRAM data bus 05
111 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
112 D04 DATA4 I/O SDRAM data bus 04
113 D03 DATA3 I/O SDRAM data bus 03
114 D02 DATA2 I/O SDRAM data bus 02
115 D01 DATA1 I/O SDRAM data bus 01
116 D00 DATA0 I/O SDRAM data bus 00
117 DGND GND – Ground of external
118 VDDEXT VDDEXT – I/O power supply (EX3.3)
119 – /BG O
120 – /BGH O

42
 RX-V363/HTR-6130

Pin No. Port Name Function Name I/O Detail of Function

121 A19 ADDR19 O SDRAM address bus 19
122 A18 ADDR18 O SDRAM address bus 18
123 A17 ADDR17 O SDRAM address bus 17
124 A16 ADDR16 O SDRAM address bus 16
125 A15 ADDR15 O SDRAM address bus 15
126 A14 ADDR14 O SDRAM address bus 14
127 A13 ADDR13 O SDRAM address bus 13
128 DGND GND – Ground of external
129 DGND GND – Ground of external
130 DGND GND – Ground of external
131 DGND GND – Ground of external
132 DGND GND – Ground of external
133 DGND GND – Ground of external
134 VDDEXT VDDEXT – I/O power supply (EX3.3)

RX-V363/HTR-6130
135 A12 ADDR12 O SDRAM address bus 12
136 A11 ADDR11 O SDRAM address bus 11
137 A10 ADDR10 O SDRAM address bus 10
138 A09 ADDR9 O SDRAM address bus 09
139 A08 ADDR8 O SDRAM address bus 08
140 A07 ADDR7 O SDRAM address bus 07
141 A06 ADDR6 O SDRAM address bus 06
142 A05 ADDR5 O SDRAM address bus 05
143 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
144 DGND GND – Ground of external
145 VDDEXT VDDEXT – I/O power supply (EX3.3)
146 A04 ADDR4 O SDRAM address bus 04
147 A03 ADDR3 O SDRAM address bus 03
148 A02 ADDR2 O SDRAM address bus 02
149 A01 ADDR1 O SDRAM address bus 01
150 SDQM1 /ABE1 O SDRAM byte enable/data mask 1
151 SDQM0 /ABE0 O SDRAM byte enable/data mask 0
152 /AWE /AWE O Write enable (Asynchronous)
153 /ARE /ARE O Read enable
154 /AOE /AOE O Output enable
155 DGND GND – Ground of external
156 VDDEXT VDDEXT – I/O power supply (EX3.3)
157 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
158 /AMS3 /AMS3 O Bank select 3
159 /AMS2 /AMS2 O Bank select 2
160 /AMS1 /AMS1 O Bank select 1
161 /AMS0 /AMS0 O Bank select 0
162 ARDY ARDY I Hardware ready control
163 /BR /BR I (Pull-up)
164 SA10 SA10 O A10 pin
165 /SWE /SWE O Write enable (Synchronization)
166 /SCAS /SCAS O Sequence address strobe
167 /SRAS /SRAS O Line address strobe
168 VDDINT VDDINT – Power supply of microprocessor (BF1.2)
169 CLKOUT CLKOUT O Clock output
170 DGND GND – Ground of external
171 VDDEXT VDDEXT – I/O power supply (EX3.3)
172 /SMS /SMS O Bank select
173 SCKE SCKE O Clock enable
174 DGND GND – Ground of external
175 DGND GND – Ground of external
176 DGND GND – Ground of external

43
 RX-V363/HTR-6130

• Microprocessor extended port

IC204-IC206: SN74LV573APWR (DSP P.C.B.)

Octal 3-state D-latches with 3-state outputs

1
OE
OE 1 20 VCC
11 1D 2 19
LE 1Q
2D 3 18 2Q
C1 19
2 1Q 3D 4 17 3Q
1D 1D
4D 5 16 4Q
5D 6 15 5Q
6D 7 14 6Q
7D 8 13 7Q
8D 9 12 8Q
C8 12 GND 10 11 LE
9 8Q
8D 8D
RX-V363/HTR-6130

IC204
Pin No. Port Name Function Name Detail of Function
1 /OE /EXPE Extended port enable
2 1D D00 Data bus 00
3 2D D01 Data bus 01
4 3D D02 Data bus 02
5 4D D03 Data bus 03
6 5D D04 Data bus 04
7 6D D05 Data bus 05
8 7D D06 Data bus 06
9 8D D07 Data bus 07
10 GND DGND Ground of external
11 LE LEEX1 Bank select 1
12 8Q /SPISEL3 CS for CODEC IC (IC301, DSP P.C.B.)
13 7Q ADSEL2 4ch ADC input select 2
14 6Q ADSEL1 4ch ADC input select 1
15 5Q ADSEL0 4ch ADC input select 0
16 4Q /CCBE SPI bus switch
17 3Q /CMT Center mute
18 2Q /SMT Surround mute
19 1Q /FMT Front mute
20 VCC EX3.3 Power supply

IC205
Pin No. Port Name Function Name Detail of Function
1 /OE /EXPE Extended port enable
2 1D D08 Data bus 08
3 2D D09 Data bus 09
4 3D D10 Data bus 10
5 4D D11 Data bus 11
6 5D D12 Data bus 12
7 6D D13 Data bus 13
8 7D D14 Data bus 14
9 8D D15 Data bus 15
10 GND DGND Ground of external
11 LE LEEX1 Bank select 1 (B, G, E, F models)
12 8Q CLKSEL/RDS_RST Reset for RDS (B, G, E, F models)
13 7Q SSEL3 SCENE select LED switch 3
14 6Q SSEL2 SCENE select LED switch 2
15 5Q SSEL1 SCENE select LED switch 1
16 4Q /IC_AK IC for CODEC IC (IC301, DSP P.C.B.) and VFD (IC201, OPERATION P.C.B.)
17 3Q /SPISEL4 CS for VFD (IC201, OPERATION P.C.B.)
18 2Q /3.3SW +3.3S switch
19 1Q PRY Power relay
20 VCC EX3.3 Power supply

44
 RX-V363/HTR-6130

RX-V363/HTR-6130
IC206
Pin No. Port Name Function Name Detail of Function
1 /OE /EXPE Extended port enable
2 1D D00 Data bus 00
3 2D D01 Data bus 01
4 3D D02 Data bus 02
5 4D D03 Data bus 03
6 5D D04 Data bus 04
7 6D D05 Data bus 05
8 7D D06 Data bus 06
9 8D D07 Data bus 07
10 GND DGND Ground of external
11 LE LEEX2 Bank select 2
12 8Q /VR1 Video select R
13 7Q SPISEL5 CE for tuner
14 6Q /8ohmSW AC H/L relay (RY106, MAIN P.C.B.)
15 5Q HPRY Headphone relay (RY102, MAIN P.C.B.)
16 4Q MRYA Main speakers A relay (RY101, MAIN P.C.B.)
17 3Q MRYB Main speakers B relay (RY102, MAIN P.C.B.)
18 2Q CSRY Center/surround speakers relay (RY103/RY105, MAIN P.C.B.)
19 1Q /SWMT Subwoofer mute
20 VCC EX3.3 Power supply

45
 RX-V363/HTR-6130

• Microprocessor ADC select port

IC401: ADC084S021CIMM (DSP P.C.B.)

4-channel, 200 kSPS, 8-bit A/D converter

IN1

IN2 8-Bit VA
SUCCESSIVE CS 1 10 SCLK
IN3 MUX T/H
APPROXIMATION VA 2 9 DOUT
GND
ADC
GND 3 ADC084S021 8 DIN
IN4 GND
IN4 4 7 IN1
IN3 5 6 IN2
SCLK
CONTROL CS
LOGIC DIN
RX-V363/HTR-6130

DOUT

Pin No. Port Name Function Name Detail of Function

1 /CS /SPISEL1 CS for microprocessor
2 VA VA +3.3S
3 GND DGND Ground of external
4 IN4 IN4 SPI bus COM (IC402)
5 IN3 IN3 SPI bus COM (IC403)
6 IN2 KEY1 Key input 1
7 IN1 KEY0 Key input 0
8 DIN SPIMO Master output/slave input
9 DOUT SPIMI Master input/slave output
10 SCLK SPISCK SPI clock

Key input (A/D), pull-up resistance 10 k-ohms

Ohm [ohm] +1.0 k +1.0 k +1.5 k +2.2 k +3.3 k +4.7 k +4.7 k +6.8 k +10.0 k +22.0 k
V [V] 0.3 0.55 0.86 1.2 1.56 1.91 2.14 2.36 2.57 2.81
PROGRAM PROGRAM TONE SEARCH
KEY0 (7 pin) SCENE 1 SCENE 2 < > STRAIGHT CONTROL MODE FM/AM A/B/C/D/E SPEAKERS
AUDIO PRESET/ PRESET/
KEY1 (6 pin) SCENE 3 SCENE 4 DIRECT SELECT INPUT < INPUT > TUNING < TUNING > MEMORY TUNING

IC402, IC403: SN74LV4051APWR (DSP P.C.B.)

8-channel analog multiplexers/demultiplexers

3
COM

13
Y0

14
11 Y1
A

15
Y2

12 INPUTS ON
10 Y3 Y4 1 16 VCC
B INH C B A CHANNEL
Y6 2 15 Y2
1 COM 3 14 L L L L Y0
Y4 Y1
4 13 L L L H Y1
Y7 Y0
5 5 12
L L H L Y2
9 Y5 Y5 Y3
C L L H H Y3
INH 6 11 A
10
L H L L Y4
2 GND 7 B
Y6 L H L H Y5
GND 8 9 C
L H H L Y6
4
6 Y7 L H H H Y7
INH
H X X X None

46
 RX-V363/HTR-6130

IC402
Pin No. Port Name Function Name Detail of Function
1 Y4 –
2 Y6 –
3 COM COM SPI bus IN4 (IC401)
4 Y7 LINKACTIVE Link detect (U, C models)
5 Y5 XM_MUTE
6 INH DGND (Pull-down)
7 GND DGND Ground of external
8 GND DGND Ground of external
9 COM ADSEL2 Input select 2

RX-V363/HTR-6130
10 B ADSEL1 Input select 1
11 A ADSEL0 Input select 0
12 Y3 –
13 Y0 –
14 Y1 /ST Stereo for tuner
15 Y2 /TUNED Tuned for tuner
16 Vcc +3.3S Power supply

IC403
Pin No. Port Name Function Name Detail of Function
1 Y4 DEST Destination 1 *
2 Y6 /PDET Sub-trans detect
3 COM COM SPI bus IN3 (IC401)
4 Y7 /HP Headphone detect
5 Y5 PRIIN Current protection
6 INH DGND (Pull-down)
7 GND DGND Ground of external
8 GND DGND Ground of external
9 COM ADSEL2 Input select 2
10 B ADSEL1 Input select 1
11 A ADSEL0 Input select 0
12 Y3 PLDET Limiter detect
13 Y0 PRDIN Amplifier DC detect
14 Y1 PRVIN Voltage protection
15 Y2 THMIN Thermo protection
16 Vcc +3.3S Power supply

* Destination for A/D port

R406 [ohm] 1.5 k 3.3 k 4.7 k 6.8 k 8.2 k
R407 [ohm] 8.2 k 6.8 k 5.6 k 3.9 k 2.2 k
DEST (1 pin) [V] 2.6-3.0 2.0-2.4 1.6-2.0 1.0-1.4 0.5-0.9
A/D value (3.3 V=255) 206-226 162-182 129-149 83-103 44-64
Destination U, C R, L T K, A B, G, E, F

47
 RX-V363/HTR-6130

IC301: AK4588VQ (DSP P.C.B.)

2/8-channel audio CODEC with DIR

PVSS PVDD R XTI XTO

RX0 X'tal
RX1 Clock Oscillator
RX2 8 to 3 Recovery Clock MCKO1
RX3 Input Generator MCKO2
RX4
Selector
RX5 DEM
RX6
DAIF LRCK2
RX7 Audio
BICK2
Decoder I/F
SDTO2
TX0
DAUX2
PDN

TX1
I2C
RX-V363/HTR-6130

AVDD DIT
AVSS
DVDD CSN
Error & Q-subcode CCLK
DVSS AC-3/MPEG uP I/F
STATUS buffer CDTO
TVDD Detect Detect CDTI
VIN

B,C,U, INT0
VOUT INT1

LIN ADC HPF

Audio
I/F
RIN ADC HPF

LOUT1 LPF DAC DATT

DEM MCLK MCLK
DATT LRCK LRCK1
ROUT1 LPF DAC
DEM BICK BICK1

LPF DAC DATT DAUX1

LOUT2
DEM

DATT Format
ROUT2 LPF DAC
DEM Converter

LOUT3 LPF DAC DATT SDOUT

DEM

DAC DATT SDTO1

ROUT3 LPF
DEM SDIN1 SDTI1
SDIN2 SDTI2
LPF DAC DATT SDIN3 SDTI3
LOUT4 SDIN4
DEM SDTI4

ROUT4 LPF DAC DATT

DEM
DAUX2

TEST2
MCLK

PVDD
CAD1

CAD0

PVSS
INT0

RX7

RX6

RX5

RX4

RX3

RX2
TX1
TX0

VIN

I2C

NC
R
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
80
79

INT1 1 60 TEST1
BOUT 2 59 RX1
TVDD 3 58 NC
DVDD 4 57 RX0
DVSS 5 56 AVSS
XTO 6 55 AVDD
XTI 7 54 VREFH
TEST3 8 53 VCOM
MCKO2 9 52 RIN
MCKO1 10 51 LIN
COUT 11 50 NC
UOUT 12 49 ROUT1
VOUT 13 48 NC
SDTO2 14 47 LOUT1
BICK2 15 46 NC
LRCK2 16 45 ROUT2
SDTO1 17 44 NC
BICK1 18 43 LOUT2
LRCK1 19 42 NC
CDTO 20 41 ROUT3
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
CCLK/SCL
CDTI/SDA
CSN
DAUX1
SDTI4
SDTI3
SDTI2
SDTI1
XTL1
XTL0
PDN
MASTER
DZF2
DZF1

ROUT4
LOUT4
NC

NC
LOUT3
NC

48
 RX-V363/HTR-6130

Pin No. Function Name I/O Detail of Function

1 INT1 O Interrupt 1 pin

2 BOUT O Block-start output pin for receiver input “H” during first 40 flames

3 TVDD – Output buffer power supply pin, 2.7 V to 5.5 V

4 DVDD – Digital power supply pin, 4.5 V to 5.5 V
5 DVSS – Digital ground pin
6 XTO O X’tal clock output pin
7 XTI I X’tal / External clock input pin
Test 3 pin
8 TEST3 I
This pin should be connected to DVSS
9 MCKO2 O Master clock output 2 pin
10 MCKO1 O Master clock output 1 pin
11 COUT O C-bit output pin for receiver input

RX-V363/HTR-6130
12 UOUT O U-bit output pin for receiver input
13 VOUT O V-bit output pin for receiver input
14 SDTO2 O Audio serial data output pin (DIR/DIT part)
15 BICK2 I/O Audio serial data clock pin (DIR/DIT part)
16 LRCK2 I/O Channel clock pin (DIR/DIT part)
17 SDTO1 O Audio serial data output pin (ADC/DAC part)
18 BICK1 I/O Audio serial data clock pin (ADC/DAC part)
19 LRCK1 I/O Input channel clock pin
20 CDTO O Control data output pin in serial mode, I2C pin= “L”
CCLK I Control data clock pin in serial mode, I2C pin= “L”
21
SCL I Control data clock pin in serial mode, I2C pin= “H”
CDTI I Control data input pin in serial mode, I2C pin= “L”
22
SDA I/O Control data pin in serial mode, I2C pin= “H”
I Chip select pin in serial mode, I2C pin=”L”
23 CSN
I This pin should be connected to DVSS, I2C pin=”H”
24 DAUX1 I AUX audio serial data input pin (ADC/DAC part)
25 SDTI4 I DAC4 audio serial data input pin
26 SDTI3 I DAC3 audio serial data input pin
27 SDTI2 I DAC2 audio serial data input pin
28 SDTI1 I DAC1 audio serial data input pin
29 XTL1 I X’tal frequency select 0 pin
30 XTL0 I X’tal frequency select 1 pin
Power-down mode pin
31 PDN I When “L”, the AK4588 is powered-down, all output pin goes “L”, all registers are reset
When CAD1-0 pins are changed, the AK4588 should be reset by PDN pin
Master mode select pin
32 MASTER I
“H”: Master mode, “L”: Slave mode
Zero input detect 2 pin (table 13)
DZF2 O When the input data of the group 1 follow total 8192 LRCK cycles with “0” input data, this pin
goes to “H” / When RSTN1 bit is “0” or PWDAN bit is “0”, this pin goes to “H”
33
Analog input overflow detect pin
OVF O This pin goes to “H” if the analog input of L ch or R ch overflows
This pin becomes OVF pin if OVFE bit is set to 1
Zero input detect 1 pin (table 13)
34 DZF1 O When the input data of the group 1 follow total 8192 LRCK cycles with “0” input data, this pin
goes to “H” / When RSTN1 bit is “0” or PWDAN bit is “0”, this pin goes to “H”
35 LOUT4 O DAC4 L ch analog output pin
No connect pin
36 NC –
No internal bonding / This pin should be opened
37 ROUT4 O DAC4 R ch analog output pin
No connect pin
38 NC –
No internal bonding / This pin should be opened
39 LOUT3 O DAC3 L ch analog output pin
No connect pin
40 NC –
No internal bonding / This pin should be opened
49
 RX-V363/HTR-6130

Pin No. Function Name I/O Detail of Function

41 ROUT3 O DAC3 R ch analog output pin
No connect pin
42 NC –
No internal bonding / This pin should be opened
43 LOUT2 O DAC2 L ch analog output pin
No connect pin
44 NC –
No internal bonding / This pin should be opened
45 ROUT2 O DAC2 R ch analog output pin
No connect pin
46 NC –
No internal bonding / This pin should be opened
47 LOUT1 O DAC1 L ch analog output pin
No connect pin
48 NC –
No internal bonding / This pin should be opened
49 ROUT1 O DAC1 R ch analog output pin
RX-V363/HTR-6130

No connect pin
50 NC –
No internal bonding / This pin should be opened
51 LIN I L ch analog input pin
52 RIN I R ch analog input pin
Common voltage output pin
53 VCOM –
2.2 F capacitor should be connected to AVSS externally
54 VREFH – Positive voltage reference input pin, AVDD
55 AVDD – Analog power supply pin, 4.5 V to 4.5 V
56 AVSS – Analog ground pin, 0 V
57 RX0 I Receiver channel 0 pin (Internal biased pin / Internally biased at PVDD/2)
No connect pin
58 NC –
No internal bonding / This pin should be connected to PVSS
59 RX1 I Receiver channel 1 pin (Internal biased pin / Internally biased at PVDD/2)
Test 1 pin
60 TEST1 I
This pin should be connected to PVSS
61 RX2 I Receiver channel 2 pin (Internal biased pin / Internally biased at PVDD/2)
No connect pin
62 NC –
No internal bonding / This pin should be connected to PVSS
63 RX3 I Receiver channel 3 pin (Internal biased pin / Internally biased at PVDD/2)
64 PVSS – PLL ground pin
External resistor pin
65 R –
12 k-ohms +/-1 % resistor should be connected to PVSS externally
66 PVDD – PLL power supply pin, 4.5 V to 4.5 V
67 RX4 I Receiver channel 4 pin (Internal biased pin / Internally biased at PVDD/2)
Test 2 pin
68 TEST2 I
This pin should be connected to PVSS
69 RX5 I Receiver channel 5 pin (Internal biased pin / Internally biased at PVDD/2)
70 CAD0 I Chip address 0 pin (ADC/DAC part)
71 RX6 I Receiver channel 6 pin (Internal biased pin / Internally biased at PVDD/2)
72 CAD1 I Chip address 1 pin (ADC/DAC part)
73 RX7 I Receiver channel 7 pin (Internal biased pin / Internally biased at PVDD/2)
Control mode select pin
74 I2C I
“L”: 4-wire serial, “H”: I2C bus
75 DAUX2 I Auxiliary audio data input pin (DIR/DIT part)
76 VIN I V-bit input pin for transmitter output
77 MCLK I Master clock input pin
78 TX0 O Transmit channel (through data) output 0 pin
Transmit channel output 1 pin
79 TX1 O When TX bit = “0”, transmit channel (through data) output 1 pin.
When TX bit = “1”, transmit channel (DAUX2 data) output pin (default)
80 INT0 O Interrupt 0 pin

Note: All input pins except internal biased pins and internal pull-down pin should not be left floating.

50
 RX-V363/HTR-6130

IC161: R2A15218FP (MAIN P.C.B.)

8-channel electronic volume with 11 input selector and tone control

BASSR2

BASSR1
SBRCIN
SBLCIN

SBRIN2
CLOCK

SBLIN2
SWIN2
DGND

SRIN2
FRIN2
SUBR

SLIN2
FLIN2

TRER
SUBL
DATA

CIN2

N.C.

N.C.
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
A VCC
MUTE 51 30 A VCC
MCU
A VEE 52 I/F 29 N.C.
A VEE
N.C. 53 28 TREL
0/-6/-12/-18dB

RX-V363/HTR-6130
ADCL 54 27 BASSL2
ATT
ADCR 55 26 BASSL1
AGND 56 Bass/Treble 25 N.C.
0~-95dB, -14~+14dB
MAIN -∞ (2dBstep) +42~0dB
N.C. 57 SUB (0.5dBstep) Bypass (0.5dBstep) 24 FRC
MAIN
MAIN

Tone+MIX Tone
INR1 58 Tone 23 FROUT

INL1 59 +42~0dB 22 A GND

(0.5dBstep)

INR2 60 Tone 21 FLOUT

Tone+MIX Tone
SUB

INL2 61 Bass/Treble Bypass 20 FLC

0~95dB,
-∞ -14~+14dB
(0.5dBstep) (2dBstep)
INR3 62 19 A GND
SUB

CMIX
INL3 63 18 CC
+42~-95dB
-∞(0.5dBstep)
INR4 64 17 COUT

SWMIX
INL4 65 16 A GND
+42~-95dB
INR5 66 -∞(0.5dBstep) 15 SWOUT
+42~-95dB
-∞(0.5dBstep)
INL5 67 14 SWC

INR6 68 13 N.C.
INL6 69 +42~-95dB 12 SRC
-∞(0.5dBstep)

INR7 70 11 SROUT
INL7 71 +42~-95dB 10 A GND
-∞(0.5dBstep)
INR8 72 9 SLOUT

INL8 73 8 SLC
N.C. 74 +42~-95dB 7 A GND
-∞(0.5dBstep)
INRA/RECR1 75 6 SBRC
REC
INLA/RECL1 76 5 SBR OUT

N.C. 77 4 A GND
INR9 78 3 SBL OUT

INL9 79 2 SBLC
N.C. 80 1 N.C.

81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
INRB/RECR2

INLB/RECL2

INR10/RECR4

INL10/RECL4

INR11/RECR5

INL11/RECL5
N.C.

N.C.

N.C.
RECR3

RECL3

N.C.

FLIN1

FRIN1

CIN1

SWIN1

SLIN1

SRIN1

SBLIN1

SBRIN1

51
 RX-V363/HTR-6130

Pin No. Function Name Detail of Function

1 N.C. No connected
2 SBLC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
3 SBLOUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
4 AGND Analog GND terminal
5 SBROUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
6 SBRC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
7 AGND Analog GND terminal
8 SLC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
9 SLOUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
10 AGND Analog GND terminal
11 SROUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
12 SRC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
RX-V363/HTR-6130

13 N.C. No connected
14 SWC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
15 SWOUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
16 AGND Analog GND terminal
17 COUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
18 CC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
19 AGND Analog GND terminal
20 FLC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
21 FLOUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
22 AGND Analog GND terminal
23 FROUT FL/FR/C/SW/SL/SR/SBL/SBR ch output terminal
24 FRC L/R/C/SW/SL/SR/SBL/SBR ch terminal to connect capacitor to reduce noise from changing the volume
25 N.C. No connected
26 BASSL1 L/R ch tone control (Bass) terminal for setting frequency characteristics
27 BASSL2 L/R ch tone control (Bass) terminal for setting frequency characteristics
28 TREL L/R ch tone control (Treble) terminal for setting frequency characteristics
29 N.C. No connected
30 AVCC Positive side power terminal
31 N.C. No connected
32 BASSR1 L/R ch tone control (Bass) terminal for setting frequency characteristics
33 BASSR2 L/R ch tone control (Bass) terminal for setting frequency characteristics
34 TRER L/R ch tone control (Treble) terminal for setting frequency characteristics
35 N.C. No connected
36 SBLIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
37 SBRIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
38 CIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
39 SWIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
40 SLIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
41 SRIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
42 FLIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
43 FRIN2 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
44 SBRCIN SBL/SBR ch volume input terminal
45 SBLCIN SBL/SBR ch volume input terminal
46 SUBL L/R ch SUB output terminal
47 SUBR L/R ch SUB output terminal
48 DGND Digital GND terminal
49 DATA Control data input terminal
50 CLOCK Control data input terminal
51 MUTE External Mute Control terminal
52 AVEE Negative side power terminal
53 N.C. No connected
54 ADCL L/R ch ADC output terminal
55 ADCR L/R ch ADC output terminal

52
 RX-V363/HTR-6130

Pin No. Function Name Detail of Function

56 AGND Analog GND terminal
57 N.C. No connected
58 INR1 L/R ch input terminal (input selector)
59 INL1 L/R ch input terminal (input selector)
60 INR2 L/R ch input terminal (input selector)
61 INL2 L/R ch input terminal (input selector)
62 INR3 L/R ch input terminal (input selector)
63 INL3 L/R ch input terminal (input selector)
64 INR4 L/R ch input terminal (input selector)
65 INL4 L/R ch input terminal (input selector)
66 INR5 L/R ch input terminal (input selector)
67 INL5 L/R ch input terminal (input selector)

RX-V363/HTR-6130
68 INR6 L/R ch input terminal (input selector)
69 INL6 L/R ch input terminal (input selector)
70 INR7 L/R ch input terminal (input selector)
71 INL7 L/R ch input terminal (input selector)
72 INR8 L/R ch input terminal (input selector)
73 INL8 L/R ch input terminal (input selector)
74 N.C. No connected
75 INRA/RECR1 L/R ch input terminal (input selector) / L/R ch REC output terminal
76 INLA/RECL1 L/R ch input terminal (input selector) / L/R ch REC output terminal
77 N.C. No connected
78 INR9 L/R ch input terminal (input selector)
79 INL9 L/R ch input terminal (input selector)
80 N.C. No connected
81 INRB/RECR2 L/R ch input terminal (input selector) / L/R ch REC output terminal
82 INLB/RECL2 L/R ch input terminal (input selector) / L/R ch REC output terminal
83 INR10/RECR4 L/R ch input terminal (input selector) / L/R ch REC output terminal
84 INL10/RECL4 L/R ch input terminal (input selector) / L/R ch REC output terminal
85 INR11/RECR5 L/R ch input terminal (input selector) / L/R ch REC output terminal
86 INL11/RECL5 L/R ch input terminal (input selector) / L/R ch REC output terminal
87 N.C. No connected
88 N.C. No connected
89 N.C. No connected
90 RECR3 L/R ch REC output terminal
91 RECL3 L/R ch REC output terminal
92 N.C. No connected
93 FLIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
94 FRIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
95 CIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
96 SWIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
97 SLIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
98 SRIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
99 SBLIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)
100 SBRIN1 L/R/C/SW/SL/SR/SBL/SBR ch input terminal (multi input 1/2)

53
 RX-V363/HTR-6130

IC201: M66003-0131FP-R (OPERATION P.C.B.)

18 digit 5x7 segment VFD controller/driver

Display code
RAM CGROM
(35 bit x 166) 44 SEG00
(8-bit x 60)
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data
CGROM 9 SEG34
CS 2 Serial data (35 bit x 16)
write
SCK 3 receive
circuit Code/
SDATA 4 command
control 45 SEG35
circuit DIG11/
52
SEG42
51 DIG12/
SEG41
code Segment/
50 DIG13/
select Digit SEG40
select/ DIG14/
49
XIN 7 Clock output SEG39
timing Display
generator clock controller scan pulse circuit 48 DIG15/
XOUT 6 SEG38
47 DIG16/
SEG37
46 DIG17/
RX-V363/HTR-6130

SEG36

63 DIG00
Digit
RESET 1 output
Vcc1 8 circuit
53 DIG10
Vcc2 18
Vss 5
Vp 64

DIG11/SEG42
DIG12/SEG41
DIG13/SEG40
DIG14/SEG39
DIG00
DIG01
DIG02
DIG03
DIG04
DIG05
DIG06
DIG07
DIG08
DIG09
DIG10
VP

RESET DIG15/SEG38
CS DIG16/SEG37
SCK DIG17/SEG36
SDATA SEG35
Vss SEG00
XOUT SEG01
XIN SEG02
Vcc1 SEG03
SEG34 SEG04
SEG33 SEG05
SEG32 SEG06
SEG31 SEG07
SEG30 SEG08
SEG29 SEG09
SEG28 SEG10
SEG27 SEG11
SEG26
Vcc2
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12

54
 RX-V363/HTR-6130

Pin No. Port Name Function Name I/O Detail of Function

1 Reset /RESET Reset input When "L", M66003 is initialized
2 CS /CEFL Chip select input When "L", communication with the MCU is possible
When "H", any instruction from the MCU is neglected
3 SCK CKFL Shift clock input
Serial input data is taken and shifted by the positive edge of SCK
4 SDATA DTFL Serial data input
5 Vss VSS GND (0V)
6 XOUT XOUT Clock output When use as a CR oscillator, connect external resistor and capacitor / When
7 XIN XIN Clock input use an external clock, input external clock to XIN, and XOUT must be opened
8 Vcc1 VDD Positive power supply for internal logic
9 SEG34 P1I Segment output
10 SEG33 P2 Segment output
11 SEG32 P3 Segment output
12 SEG31 P4 Segment output
13 SEG30 P5 Segment output Positive power supply for DIG and SEG outputs
14 SEG29 P6 Segment output
15 SEG28 P7 Segment output
16 SEG27 P8 Segment output
17 SEG26 P9 Segment output
18 Vcc2 VDD
19 SEG25 P10 Segment output
20 SEG24 P11 Segment output
21 SEG23 P12 Segment output
22 SEG22 P13 Segment output
23 SEG21 P14 Segment output
24 SEG20 P15 Segment output
25 SEG19 P16 Segment output
26 SEG18 P17 Segment output
27 SEG17 P18I Segment output
28 SEG16 P19 Segment output
29 SEG15 P20 Segment output
30 SEG14 P21 Segment output
31 SEG13 P22 Segment output
32 SEG12 P23 Segment output
Connect to segment (anode) pins of VFD
33 SEG11 P24 Segment output
34 SEG10 P25 Segment output
35 SEG09 P26 Segment output
36 SEG08 P27 Segment output
37 SEG07 P28 Segment output
38 SEG06 P29 Segment output
39 SEG05 P30 Segment output
40 SEG04 P31 Segment output
41 SEG03 P32 Segment output
42 SEG02 P33 Segment output
43 SEG01 P34 Segment output
44 SEG00 P35 Segment output
45 SEG35 P36 Segment output
46 DIG17/SEG36 P37 Segment output
47 DIG16/SEG37 G17I Digit output
48 DIG15/SEG38 G16I Digit output
49 DIG14/SEG39 G15I Digit output
50 DIG13/SEG40 G14 Digit output
51 DIG12/SEG41 G13 Digit output
52 DIG11/SEG42 G12 Digit output
53 DIG10 G11 Digit output
54 DIG09 G10 Digit output
55 DIG08 G9 Digit output Connect to digit (grid) pins of VFD
56 DIG07 G8 Digit output
57 DIG06 G7 Digit output
58 DIG05 G6 Digit output
59 DIG04 G5 Digit output
60 DIG03 G4 Digit output
61 DIG02 G3 Digit output
62 DIG01 G2 Digit output
63 DIG00 G1 Digit output
64 Vp VP Negative power supply to pull down

55
 A B C D E F G H I J
RX-V363/HTR-6130

1
■ BLOCK DIAGRAMS
VIDEO, AUDIO and Power Supply Sections
• See page 73-78 →
OPERATION DSP SCHEMATIC DIAGRAM OPERATION
• See page 79, 80 → VIDEO COMPONET VIA POWER SUPPLY • See page 79, 80 →
SCHEMATIC DIAGRAM VIB
SCHEMATIC DIAGRAM
R1814 10K Power supply for
Power supply for BN74HC245 (IC404) Power supply for
VR1 IGND +5I Power supply for iPod
AK4588 (IC301) SN74LVU04 (IC305) component video circuit
GP1FA553RZDF (U301,302) RDS decoder circuit (U, C models)
MONITOR OUT LOGIC HGND 5HDMI 5HDMI
R1816 10K +5AAK +5DAK +5D +5 Power supply for Power supply for IC239

PS
VIA VIB PS MONITOR power amplifier pre amp stage. power amplifier final stage. KIA7805
H H H DVD -BV +BV -B +B

23
IC181

2
+5
7,21 L H H DTV/CBL IC311
NJM2586AM D2169
2 DVD
5,12,13
16,18 H L H DVR KIA7805 IGND

6dB L L L MUTE(V-AUX)
3,10,15 20,22,24 LIM
-5
DTV/CBL H L L MUTE(iPod )
COMPONENT VIDEO

1,8,17 6,9,11,14,19 /8ohmSW

SELECTOR & MONITOR OUT LOGIC Power supply for IC234 AC5
VIDEO AMP operation amplifier
VCR VIA VIB VR1 MONITOR Power supply for Power supply for KIA7805 AC5
speaker relay
BD3816 (IC3) TUNER UNIT composite video circuit. (-12 only)
H H L DVD AC4
-7 +7 +10 -12 +12
MONITOR OUT L H L DTV/CBL AC4 POWER TRANSFORMER
H L H DVR Q8 D2163
Limiter circuit for ACL
L L L V-AUX positive power supply. C1050
Q182 (Q109,110,112) ACH
H L L iPod
VIDEO
Q6 IC236
DVD RY106
KIA7812
C1051 ACH
AC IN
4,10

DTV/CBL
14

ACL
6

C203
IC182 2,16 +5 R1816
NJM2595M D120
3 10K Limiter circuit for POWER CABLE
8 Select for speaker
Q183 negative power supply.
5
(Q111,113,114) impedance 4O or 6O AC2
6dB
9 15
-5 C204
V-AUX 10K R1816
3 13
SELECTOR &
12 Q184
Q7
KIA7912
AC2
VIDEO AMP IC237 Power supply for D173 AC3
10K R1816 Q4 BLACK FIN and peripheral IC232
1

+3.3 NJM2388F33 AC3

Power supply for Power supply for EX33. SD3.3 BF3.3
XM AK4588(IC301) R2A15215,ADCOB4
DVR IN AC6
(+3.3X) +3.3DAK +3.3S
AC6
/VIA

/VIB
VIDEO

C2178
-5 For FL display filament
MONITOR OUT
Power supply for F1
component video circuit
DVR OUT D
F2
DIODE D2164
Q501

• See page 73-78 →

(R, K, A, B, G, E, F, L models) DSP SCHEMATIC DIAGRAM
HDMI VIDEO SELECT OPTIMIZER
HDMI SWITCHER /VIA /VIB
• See page 83 → L L DVD
SELECTOR and VOLUME /3.3SW
MIC
SCHEMATIC DIAGRAM H L DTV C373 SUB TRANSFORMER
IC161
4
62 T251
27,28,30,31,33,34,39,40 ANT D2253,2254,2256,2257
DTV/CBL
FM/AM 66,67
TUNER
HDMI IN

TUNER
IC903
70,71
CXB1442AR CD TONE
+3.3
CONTROL
68,69
3,4,6,7,9,10,45,46 MD/CD-R 21,23
DVD 36
/VIA 83,84
DVD
/VIB
78,79 17
DTV/CBL
INPUT SPEAKER RELAY
72,73 9,11
13,14,16,17,20,21,23,24 VCR
HDMI OUT
58,59 PHONE
V-AUX RY102
JK261
15
PORTABLE

FRONT A L/R MAIN

5 MUTE POWER AMPLIFIER
iPod DOCK
Buffer amplifier with
RY101
SP • See page 81, 82 →
adjustable gain. IC101 SCHEMATIC DIAGRAM
75,76
MD/CD-R
REC OUT 31.6dB
81,82 FRONT B L/R

SPEAKERS
VCR
RY104
SP

93,94
Selector and volume Q152,153
FRONT L/R IC101

95
CENTER 31.6dB CENTER
MULCH CH RY105
97,98 SP
INPUT SUR. L/R
Q155
96
SUBWOOFER IC102

31.6dB
R2A15215FP SUR.L/R
54,55

42,43

38

40,41

39

52

30
RY103
SP
+7 -7
IC162-164 Q151,154
6
13dB
DASL/R
DAFL/R

DASW
ADL/R

SUB WOOFER
DAC

IC169

Q451,452
DIGITAL INPUT and CODEC
51,52

47,49

43,45

Filter amplifier with gain for

DSP
39

41

IC301 removal of D/A converter noise.

• See page 73-78 → /HP

A/D DATA 17
SCHEMATIC DIAGRAM 73 A/D Converter
To microprocessor and DSP 14
DIR DATA
74 HPRY
D/A Converter
MRYA

(U, C, R, T, K, A, RX0 57
MRYB
B, G, E, L models) DI R
COAXIAL DVD
CSRY
CODEC
PJ301
AK4588
DIGITAL /FMT
59

61

RX1
26

27

28

INPUT DTV
7 OPTICAL
(J model)
U301 /SMT

RX2 /CMT
DTOPRI
CD U302 /SWMT
(U, C, R, K, To microprocessor
A, L models) and DSP

56
 A B C D E F G H I J
RX-V363/HTR-6130

Control Sections

2
• See page 79, 80 →
OPERATION SCHEMATIC DIAGRAM

/RESET from OPERATION

/RESET CONTROL LIST

Input select VIA, VIB,
DSP IC505 IC505 /VR1
SSEL1-3
• See page 73-78 →
IC202 IC201
SCHEMATIC DIAGRAM Control bus SPISEL3-5
12 /CCBE
IC204-206 /IC_AK

SDRAM FlashROM A/D select ADSEL0-2

W9864G6EH-7 S29AL008D70TFI0 ExPort1/2
1 11 Speaker relay control MRYA
3 15
/OE LE
MRYB
CSRY
HPRY

D0 - D15

D0 - D15
D0 - D15
A1 - A10,
A18, A19

A1 - A19
Mute control /FMT
/CMT
/SMT
/SWMT
Power control PRY
/8ohmSW INPUT LIST
IC203 LEEX /3.3SW Protection PDET

D0 - D15
A1 - A19
PRD
RDS control RDS_RST PRV
SA10, /SRAS, /SCAS, Logic (B, G, E, F models) PLDET
/SMS, CLKOUT, SCKE, /AWE,
/SWE, SDQM0, SDQM1 /AOE, THM
U, C models ARDY /AMS0 /AWE, /AMS1, /AMS2 ADSEL0-2
/DRESET /EXPE Keypad KEY0
CB602 IC101 KEY1
iPDET 162 51 IC102
4 /SPISEL2 /CS IC402-403
Hi or Lo PRI
4 17
iPAP 49
SPISCLK SCLK
1 11 10 9 /HP

Selector
6
EEPROM /ST
DOCK 13 SPIMO SI TUNED
RX 5
(iPod or 18 82 SPIMI SD 2 /MIC (R, K, A, B, G, E, F, L models)
Bluetooth) TX iPAP (U, C models)
14 81
IC401
/SPISEL1 /CS 4 3
1
50 KEY0
SPISCLK SCLK 7
SPISCLK
DIN
10 4ch ADC 6
KEY1 else iPDET (U, C models)
53 SPIMO
SPIMO 8 ADC084S021
DIR DATA 74 55 SPIMI DOUT 9
SPIMI
54
A/D DATA 73

IC201
/RESET
DTOPRI 26-28 /CEFD
1
OPERATION (1)
/SPISEL4 2 VFD • See page 79 →
5SPISCK CKFD
3 M66003- SCHEMATIC DIAGRAM
Microprocessor and DSP 5SPIMO DTFD
5 IC404 4 0131FP-R
ADSP-BF531

/5SPISEL6
OPERATION 9
5SPISCK
• See page 79, 80 → SPISCLK 5SPISCK
SPIMO
14 Bus- 6 5SPIMO
SCHEMATIC DIAGRAM
SPIMI
13
Switch 7
5SPIMI
2 18
5SPISEL5 CEP TUNED
SPISEL5 15 3.3V <-> 5
PSW SCLK
"STANDBY/ON" key 48 5V 5SPISCK /ST
/OE
VRA /CCBE 19 5SPIMO DI TUNER
46 /ICAK 5SPIMI DO COMP
"VOLUME" VRB
38
REM RDS_RST 12 8
RDS_RST CH3 IN3 IC181
15
IR Remote 47
RDS_SW 3
RDCL
17
RDS_RDY CH1 IN1
1
6 36
LIM
5SPISCK
LIM 37
IC301 5SPIMI SW RDS
/PDN
31
/CS
PF14 28 /SPISEL3 23
MAIN VIA
SPISCLK CCLK R2A_DATA
PF15 21 SW1
• See page 81, 82 → VIB 27 SPIMO CDTI
2

SCHEMATIC DIAGRAM 22 CODEC with DIR R2A_CLK V1

16
SPIMI CDTO 20

INTAK INT0 AK4588

80
34

• See page 80 →
OPERATION (4) SCHEMATIC DIAGRAM

57
 A B C D E F G H I J
RX-V363/HTR-6130

1
■ PRINTED CIRCUIT BOARDS

DSP P.C.B. (Side A)

MAIN (1)
(CB161)

RDS_DATA
RDS_RST

R2A_CLK
/8ohmSW
OPERATION (4)

TUNED

/SWMT
SPIMO
(CB182)

MRYB
HPRY
SPIMI
2

SDTN
/CES
/VR1

VIC
VIA

IPY
IPV
OPERATION (2)

R2A_DATA
RDS_RDY
RDS_CLK
(CB232)

/OSDSEL
XMPWR

/RESET

SPICLK
/PDET

SCKN
MRYA
CSRY
+5XM
iGND

MON
R, T, K, A, B, G, E, F, L models

IPVE
IPVE
THM

CEP
PRV
PRY

+3.3

/HP

IPC
MG
MG

VIB
/ST
NC
+5I

+5
CB504
CB516
CB512

8 14

3 IC501
16
7 1 9 9 16
IC402 IC403
IC401 U, C models
8 1 8 1 1 5
10 6
27 28

B, G, E, F models

CB602

DOCK
OPERATION (1)
(CB202)

IC202
4 V_CNTL 1 10
MG No replacement part available.
+3.3S IC404
ADKEY0 11 20 20 11
ADKEY1 IC206
/CEFD
DTFD 133 176
CB408

CKFD 132 1
/RSTFD 1 54 B, G, E, F models
PSW 10 1
REM
VRA
VRB
SSEL1
SSEL2
SSEL3 IC101
/MIC
48 1

CD
5 IC201
1 20

OPTICAL
80 21
89 44
88 45

25 24
1 10 IC301

DIGITAL
1 10

DTV/

INPUT
CBL
• Semiconductor Location IC205 IC204
61 40
60 41
Ref no. Location Ref no. Location 20 11 20 11
CB408 C4 IC201 E5
CB501 E6 IC202 E4 1 7
1 7 5 8
CB502 F6 IC203 F6 IC203 IC102
IC505

COAXIAL
6 CB504 F3 IC204 E5 14 8 4 1
14 8

DVD
CB512 E3 IC205 D5 IC305
8 14
CB516 D3 IC206 D4
CB602 I4 IC301 H5
IC305 H6 CB501 CB502 7 1
D101 G4
D401 G3 IC401 G3
/FMT
/SMT
/CMT
PRI
PRD
PLDET
LIM

DAFR
E
DAFL
E
DASR
DASL
DASW
DAC
E
ADFR
ADFL
REMsense
iPL/VIA
iPAGND/VIB
iPR/VR1
D402 D3 IC402 F3
B, G, E, F models
D403 F3 IC403 F3
D404 G3 IC404 H4 MAIN (1) (CB101)
D405 G3 IC501 D3
MAIN (1) (CB164)
D408 G4 IC505 F6
7 IC101 F5 Q101 G4
IC102 F6 Q501 D3

58
 A B C D E F G H I J
RX-V363/HTR-6130

DSP P.C.B. (Side B)

R, K, A, B, G, E, F, L models U, C models

CB504
CB516
CB512

3 IC501

IC402 IC403
IC401

R, T, K, A, B, G, E, F, L models
CB602
IC202
4
IC404
IC206
CB408

IC101

5 IC201

IC301
IC205 IC204

IC203 IC505 IC102

6
IC305

CB501 CB502

B, G, E, F models

• Semiconductor Location
Ref no. Location
7 D407 F3
D409 F3
D602 G4

59
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (1) P.C.B. (Side A)

MAIN (4) (CB191)

R, K, A, B, G, E, F, L models R, K, A, B, G, E, F, L models R, K, A, B, G, E, F, L models
MIC
+12
-12
E

DSP (CB408) W2001

3
/MICDET
SSEL3 OPERATION (2)
SSEL2
SSEL1 (CB235)
VRB
VRA
CB202

REM1
PSW
/BLK F1

CB203
CKFD
DTFD VP
/CEFD
ADKEY1 F2
ADKEY0 OPERATION (10)
+3.3S
MG (CB274)
V_CN

FG
C V_CTRL
W2006 B2 PSW
04

4
VOLUME
PRESET/TUNING A/B/C/D/E

MEMORY FM/AM
TUNING SEARCH MODE
AUTO/MAN’L /EDIT

5
4 3 2 1
SCENE

AUDIO SELECT INPUT PROGRAM

DIRECT STRAIGHT SPEAKERS

EFFECT
TONE CONTROL

• Semiconductor Location
Ref no. Location
CB202 B3
CB203 I3
CB204 I4
D2001 E4
D2003 F4
7 D2005 F4
D2007 G5
D2002 D4

60
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (1) P.C.B. (Side B)

R, K, A, B, G, E, F, L models R, K, A, B, G, E, F, L models

33 32
8 5
IC202
1 4
48 17

1
20
IC
49 16

64 1

6
• Semiconductor Location
Ref no. Location Ref no. Location
D2002 D4 Q2004 H3
D2004 D4 Q2005 G3
D2006 D4 Q2011 G5
D2008 H3 Q2012 E5
D2009 H3 Q2013 E5
IC201 G3 Q2014 F5
IC202 C3 Q2015 G5
7 Q2001 F3 Q2016 F5
Q2002 E3 Q2017 F5
Q2003 F3

61
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (2) P.C.B. (Side A)

U, C models
IC236 IC237 IC232
IC233 IC234 IC239
IC238
4 1

OUT
GND
VCC

OUT
COM
IN

OUT
COM
IN

OUT
COM
IN

OUT
COM
IN

OUT
COM
IN
3

OPERATION (1)
(CB203)
CB
23

DSP (CB516)
5

AC6
VP
AC6 THM
XMPWR
PRV
PRY
/PDET
4 /RESET

CB232
+5I
IG
U, C models W2154 +5
MG
MG
+3.3
+5XM

CB233
CB234
31
CB2

5HDMI
5HDMI
HGND
AC6
AC6
AC5
AC5
AC4
AC4
AC3
AC3
AC2
E
AC2

+12
AGND
-12
+3.3
+5
PRV
VP
MG
ACDET
PRY
S9

POWER TRANSFORMER
OPERATION (3) MAIN (1) HDMI (CB905)
(CB251) (CB103)

• Semiconductor Location
Ref no. Location Ref no. Location
CB231 D5 D2164 D3
CB232 H4 D2169 C3
CB233 F5 IC232 I3
CB234 C5 IC233 G3
CB235 C4 IC234 H3
D2152 I3 IC236 G3
7 D2158 I3 IC237 G3
D2162 D3 IC238 F3
D2163 D3 IC239 H3

62
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (2) P.C.B. (Side B)

U, C models U, C models

R, T, K, A, B, G, E, F, L models
3

U, C models

• Semiconductor Location
Ref no. Location Ref no. Location
D2151 H4 D2167 C3
D2154 H4 D2168 H3
D2156 H4 D2170 C3
D2157 I3 D2171 C3
7 D2160 H4 Q2151 G4
D2165 I3 Q2152 H4
D2166 C3 Q2153 H4

63
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (3) P.C.B. (Side A) OPERATION (3) P.C.B. (Side B)

2

U, C, T, K, A, B, G, E, F models R, L models

CB254 CB252
POWER TRANSFORMER

CB257

OPERATION (2)
(CB231)

MG
R, L models ACDET
PRY
4 S9 R, L models

R, L models
CB256

AC IN

U, C, T, K, A, B, G, E, F models
U, C, T, K, A, B, G, E, F models

U, C models R, L models

6
• Semiconductor Location
Ref no. Location Ref no. Location
CB251 D4 D2256 D5
CB252 C3 D2257 D5
CB254 C3 Q2251 D3
CB256 B4 Q2252 D3
CB257 B3 Q2253 D3
D2251 D3 Q2254 D4
D2252 D4 Q2255 D4
7 D2253 D4 D2258 H4
D2254 D5 D2259 I4
D2255 D4

64
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (4) P.C.B. (Side A) OPERATION (4) P.C.B. (Side B)

MONITOR
OUT
OUT

U, C models
DVR

3 9 8
VIDEO

IN

IC183
16 1
DTV/CBL
IN

HDMI (W182)

/VIB
4
W182

/VIA
DVD
IN

GND
MONITOR OUT

13 12
PR/PB/Y

MAIN (4)

IC181
(CB193)

5
V-AUX
W181

24 1
VE
PR/PB/Y
COMPONENT VIDEO

DVR
IN

R, T, K, A, B, G, E, F, L models
MAIN (1)
(W161)
DTV/CBL

PR/PB/Y

-12
IN

+12
CB181

+5
VR1
VIB
6 VIA
PR/PB/Y
DVD

• Semiconductor Location
IN

IP_V
IP_VE
IP_Y Ref no. Location
IP_C
IP_VE
VIC CB181 D6
CB182

VIB
VIA CB182 D6
/MON
/VR1 Q181 D6
OSDSEL
/CE_OSD
SCK_OSD D181 G6
SDT_OSD
IC181 G5
IC183 G3
DSP (CB504)
7 U, C models Q182 G3
Q183 G4
Q184 G4

65
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (5) P.C.B. (Side A) OPERATION (5) P.C.B. (Side B)

R, L models
2

3 VOLTAGE
SELECTOR

CB258

POWER TRANSFORMER

OPERATION (6) P.C.B. (Side A) OPERATION (6) P.C.B. (Side B)

PHONES
SILENT CINEMA

JK261
MAIN (1)
(W103)

HPR
CB261

6 E
HPL
/HP

• Semiconductor Location
Ref no. Location
CB258 D3
CB261 C6
7 D2301 H5
D2302 H6
D2303 H6

66
 A B C D E F G H I J
RX-V363/HTR-6130

OPERATION (7) P.C.B. (Side A) OPERATION (7) P.C.B. (Side B)

MAIN (4)
(CB192)
2

AUX-V
AXR

AXL
VE
E
W2351

JK266

3
PORTABLE R L VIDEO
AUDIO
VIDEO AUX

OPERATION (10) P.C.B. (Side A) OPERATION (11) P.C.B. (Side A)

OPERATION (1)
(CB204)
5
FG
V_CTRL
PSW
CB
27
4

STANDBY
6 /ON

• Semiconductor Location
Ref no. Location
CB274 C5
D2351 I2
7 D2352 I2
D2353 H3
D2354 H3

67
 A B C D E F G H I J
RX-V363/HTR-6130

MAIN (1) P.C.B. (Side A)

MULTI CH INPUT AUDIO
MAIN (3)
FRONT SURROUND CENTER / DVD DTV/CBL DVR CD MD/CD-R SUB (W101B)
SUBWOOFER IN IN IN IN OUT WOOFER
IN OUT (PLAY) (REC) OUT

SPB_RG
SPB_LG
SPB_R

SPB_L
L/R L/R L/R L/R L/R L/R L/R L/R L/R
2
B, G, E, F models

POWER TRANSFORMER
W101A

3
ACH
ACH
DSP (CB502)

CB104
E
E NC COMP
IPR,VR1
AGND,VIB ACL +10B TUNED
IPL,VIA /ST

CB163
REMSENSE ACL TUL TMT
ADFL TE
TUR SDRP
ADFR
E SCKP SDTP
CB164

DAC CEP
DASW
DASL
DASR W161
E W103 TUNER
DAFL

HPR
HPG
HPL
/HP
4 E W163A
DAFR

LIM
PLDET OPERATION (6)
CB101

PRD (CB261)
CB161

PRI CB103
/CMT
/SMT
/FMT

DSP (CB501) W102A

SRG
SR
SL
SLG
CG
C
• Semiconductor Location
5 Ref no. Location Ref no. Location
MAIN (3)
(W102B) CB101 B4 D122 H4
CB103 E4 D123 H4
CB104 I3 IC101 F6
CB161 D4 IC102 C6
CB163 F4 Q109 H6
CB164 B4 Q110 H6
D102 H6 Q111 H6
D105 E5 Q112 H6
D106 B5 Q113 H6
D108 F5 Q114 H5
6 D109 E5 Q115 F5
D110 F5 Q116 E6
1 15 1 19 D111 G3 Q117 C5
D112 G4 Q118 F5
D113 G3 Q119 G5
R2A_DATA R2A_CLK
CSRY /SWMT D114 G5 Q120 E5
MRYB
VIA
VIB
VR1
+5
+12
-12

MRYA
AMIC
AGND
+12
-12
AXL
AGND
AXR

VP
PRV
+5
+3.3
-12
CHASSIS
+12

HPRY D115 E5 Q124 I3

/HP 8ohmSW
TMT D116 I3 Q128 E5
/ST TUNED
SPICK
SPIMI D117 F5 Q164 E4
OPERATION (4) SPIMO
(CB181) CEP RDS_RST D118 F4 Q165 D3
RDS_CLK RDS_DATA MAIN (4)
RDS_RDY (W163B) D119 G3 Q166 E3
7 OPERATION (2)
(CB233) D120 H5 Q167 F3
DSP (CB512) D121 G3

68
 A B C D E F G H I J
RX-V363/HTR-6130

MAIN (1) P.C.B. (Side B)

2
B, G, E, F models

8 IC164 5

1 4

8 IC163 5

1 4
3
U, C models

81 80

8 IC162 5 100

IC
1

16
1
51
1 4 50

8 1

30 31 IC168
9 16
R, T, K, A, B, G, E, F, L models

4 8
IC169
5

1 4

• Semiconductor Location
Ref no. Location Ref no. Location
D103 C6 Q106 B4
D104 F5 Q107 B4
D107 G5 Q108 B5
D161 E4 Q121 H3
6 D162 D3 Q122 G3
D163 E3 Q123 G4
IC161 D3 Q125 G3
IC162 B3 Q126 F4
IC163 B3 Q127 G3
IC164 B3 Q129 H3
IC168 F4 Q130 G3
IC169 B4 Q131 F4
Q101 B5 Q132 H3
Q102 B5 Q133 H3
Q103 B6 Q161 G3
7 Q104 B6 Q162 G3
Q105 B5 Q163 F3

69
 A B C D E F G H I J
RX-V363/HTR-6130

1 • Semiconductor Location
Ref no. Location
CB191 B6
CB192 B6
MAIN (3) P.C.B. (Side A) MAIN (3) P.C.B. (Side B) CB193 C7

SPEAKERS
SURROUND CENTER FRONT B
R L R L
+/- +/- +/- +/- +/-
2

W102B W101B
SRG
SR
SL
SLG
CG
C

SPB_R
SPB_RG
SPB_LG
SPB_L
4
MAIN (1)
(W102A)
MAIN (1)
(W101A)

MAIN (4) P.C.B. (Side A) MAIN (4) P.C.B. (Side B)

5
OPERATION (1) (W2001)
R, K, A, B, G, E, F, L models

-12
CB191

+12
E
MTC
OPERATION (7)
(W2351)

6 AXV
CB192

VE
AXL
E W163B
AXR
CB193

VE
VE
AXV

OPERATION (4)
MIC
E
+12
-12
AXL
E
AXR

(W181)
7
MAIN (1) (W163A)

70
 A B C D E F G H I J
RX-V363/HTR-6130

HDMI P.C.B. (Side A) HDMI P.C.B. (Side B)

HDMI
3
DTV/CBL DVD OUT
IN IN

CB903 CB902 CB901

IC902
4 5 4
1 3
1 12
48 13

IC903
37 24
36 25

IC907
1 8 IC905
IC904

GND
VIN
1 4 IC906
5 1
VOUT

16 9 4 3
8 5
IC908
5 1

5 4 3 CB904
CB905
/VIB
/VIA
GND

HGND
5HDMI
5HDMI

OPERATION (4)
(W182) OPERATION (2)
(W2154)

• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location
CB901 D3 D4913 D4 D4921 C4 D4929 B4 IC904 C5 Q4905 G4
CB902 C3 D4914 D4 D4922 C4 D4930 C4 IC905 D5 Q4906 G4
CB903 C3 D4915 C4 D4923 C4 D4931 C4 IC906 C5
CB904 C5 D4916 C4 D4924 C4 D4932 C4 IC907 C5
CB905 D5 D4917 C4 D4925 C4 D4933 D5 IC908 C5
D4909 D4 D4918 C4 D4926 C4 D4934 D5 Q4902 H4
7 D4910 D4 D4919 C4 D4927 B4 IC902 D4 Q4903 H4
D4912 D4 D4920 C4 D4928 B4 IC903 C4 Q4904 H4

71
 RX-V363/HTR-6130

■ PIN CONNECTION DIAGRAMS

• ICs • Diodes
ADC084S021 CIMM ADSP-BF531 CPU AK4588VQ BR25L320F-W EEPROM 1SS133, 176 RB160L-40 TE25 MA8075-H KDS160-RTK
1SS270A MA8100-H
1T2
132 89
60 41
MTZJ4.7A
133 88 MTZJ3.3B
61 40
Anode Anode Anode
Anode

10 5 8 4
Cathode Cathode Cathode Cathode
1 80 21 1

176 45
1 20 KBP103G 1.0A 200V 1SS355 TS6P03G 6.0A 200V
1 44
RB500V-40
KIA7805API KIA79M05PI UDZ3.6BTE-17
CXB1442AR-T4 K4S641632K-UC60000 UDZ5.1B Anode
KIA7812API KIA7912PI
UDZS3.3BTE-17
UDZS5.6BTE-17
36 25 UDZS9.1B –
54
– AC
37 24 28 AC
AC Cathode AC
+ +

IN GND
OUT OUTPUT
COM INPUT
48 13
1 12 1 27 • Transistors
LM61CIZ LC72725KM M66003-0131FP-R NJM2867F3-05 2SA1015 2SA1037K 2SA1708 2SC1740S 2SC1815
NJM2595M (TE1) 2N5401C 2SC2412K 2SC2705
SN74CB3Q3257PWR 48 33 2N5551C 2SC3326
2SD1938F
49 32

4 C
8 5
16 3 E
+VS B E
VOUT 64 17 E B C B CB
1 CB CE
GND 1 E
1 16

KRC102M-AT KRA102S-RTK/P KTA1046-Y-U/P RTQ040P02

NJM2885DL1-33 NJM2586AM NJM2388F05 NJM4565M KRA104S-RTK
NJM2388F33
KRC102S-RTK
KRC104S-RTK
4 1. Drain
2:GND OUT 6 2. Drain
3 3. Gate
COMMON 1: Base 4. Source
1 5. Drain
12 E IN 2: Collector 12 6. Drain
1. VIN 8 4 CB
24 3: Emitter 3
3:VOUT 2. VOUT
3. GND 1
1:VIN 1 1
4. ON/OFF CONTROL
4

SN74AHC02PWR SN74AHCT245PWR SN74LVC1G08DCKR

R2A15218FP SN74AHCT08PWR SN74LV573APWR
SN74LV08APWR
80 51
SN74LVU04APWR
81 50

4
10 5
3
100 31 14 7 20
1
1 30 1 1

SN74LVC2G17DCKR SN74LVC3G04DCTR SN74LV157APWR STK433-130-E STK433-330-E

SN74LV4051APWR

4
6 8 19
3 15
16
8 4
1
1 1 1
1

72
 A B C D E F G H I J K L M N

RX-V363/HTR-6130
SCHEMATIC DIAGRAMS
DSP 1/6
1
to DSP 2/6

1.5 1.5 1.5 3.4 3.4

3.4
1.5

2
2.0

1.5

1.5

3.4

3.4

1.5
0

0
EEPROM

3.4

1.8
1.5

1.9

1.9

1.8

2.0

2.1

2.1

0.9

0.9
3.4
3.4

3.4

3.4

0.2

0.2

0.2

3.3

1.9

1.9
3.4

3.4

3.4

1.3

3.5

3.5

3.4

3.4

3.4
3.4
3

3.4

3.3
0

0
0 0 0
to DSP 5/6
0 0

0 0

2.0 0
3.4 3.4

0.4 3.4 2.0

MICROPROCESSOR 0
IC102

3.4 3.3 3.4 0

0 3.4 0

0 and 0

DSP
0 0
B-2
1.7 0

4 1.9
3.4
0.2 to DSP 2/6
0.2

3.4

0 0.3

0.3
to DSP 5/6
0 0.3
3.4
0.3

0.3
1.5

to DSP 6/6 0.3

5 0.3
IC101
1.5
0.6
3.4

3.4 0

3.4 1.7

0.2 1.7

to DSP 3/6 0 1.7

3.4 1.6

0.2 1.6

0.6 1.6

3.4 1.6

1.8 1.6

6 0 0

0 3.4

3.2 0
to DSP 5/6 0 0.2

0 3.4

0 0

0 0

0 0

0 0 0
3.2

3.4

3.4

3.4

0.3

3.3

0
0.4

3.4

3.4

0.6

0.6

0.2

0.2

0.2

0.9
0
1.4

3.4

0.2

1.8

1.8
0

0.2

0
1.4

0.2

1.8
0

1.4

0.2

1.8

1.7

3.4
1.5
7

1.8
3.4
3.4

to DSP 4/6

to DSP 2/6
to DSP 6/6

to DSP 3/6, 4/6

to DSP 5/6

8 to DSP3/6

DIGITAL OUT

AD IN DIGITAL IN

9
IC101: ADSP-BF531 CPU IC102: BR25L320F-W EEPROM
Microprocessor SPI BUS 32 k-bit (4,096 x 8-bit) EEPROM

JTAG test Event controller/

Core timer Watch dock timer CS 1 VOLTAGE 8 Vcc
and emulation
INSTRUCTION DECODE DETECTION
CONTROL CLOCK
POINT B-2 XL101 (Pin 11 of IC101) GENERATION
WRITE HIGH VOLTAGE
Voltage Real time clock SO 2 INHIBITION GENERATOR 7 HOLD
regulator
UART port IrDA® INSTRUCTION
REGISTER
STATUS REGISTER
L1 order Memory L1 data
management WP 3 ADDRESS ADDRESS 6 SCK
memory memory 12bit 12bit
unit REGISTER DECODER
Timer0, Timer1, Timer2 32,768bit
EEPROM
DATA READ/WRITE
Core/System bus interface 8bit 8bit
REGISTER AMP
PPI/GPIO GND 4 5 SI
10
DMA controller
Serial port (2)
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
Boot ROM
SPI port
★ Components having special characteristics are marked s and must be replaced
External port for flash with parts having specifications equal to those originally installed.
and SDRAM control
★ Schematic diagram is subject to change without notice.

73
 A B C D E F G H I J K L M N
RX-V363/HTR-6130

1
DSP 2/6

to DSP 1/6

3.4
2 3.4
3.4
3.4 IC203

3.4
3.4
SDRAM
3.4
IC203

0 1.6 3.4

1.6 3.4 to DSP 5/6

1.6 3.4

1.6 3.4

1.6 3.4

1.7 3.4

3 1.7

1.7
3.4

0
EXTENDED PORT

IC202
0.3 0

0.3 0

0.3 0

0.3 0
to DSP 1/6
0.3 0

0.3 0

0.3

0.3

0.2

0.2
4 0.9
IC202: K4S641632K-UC60000
1.3 64 M synchronous DRAM
0.2 2.1
0.3
3.4
0.2
2.1
0.3 3.4 to DSP 5/6

I/O Control
LWE
2.0

IC204
0.3 3.4 Data Input Register
3.4 LDQM
1.8
0.3 3.3 Bank Select
3.4
3.4 1.9
3.4 0.3 3.4 to DSP 4/6
3.4

Refresh Counter
3.4 2M x 8 / 1M x16

Output Buffer
Row Decoder
1.9

Sense AMP
Row Buffer
0.3 3.3 2M x 8 / 1M x16
3.3 DQi

Address Register
1.9 2M x 8 / 1M x16
0.3 1.7 CLK
2M x 8 / 1M x16
1.9
0.3 3.3
to DSP 4/6
1.8 ADD
3.3
0.3 3.4 Column Decoder

LCBR
LRAS
5 3.4

Col. Buffer
0.2 0 3.4 Latency & Burst Length
to DSP 3/6
LCKE
Programming Register
LRAS LCBR LWE LCAS LWCBR LDQM

Timing Register

to DSP 5/6 CLK CKE CS RAS CAS WE L(U)DQM

VDD 1 54 VSS
DQ0 2 53 DQ15
VDDQ 3 52 VSSQ
0.3 3.4 DQ1 4 51 DQ14
DQ2 5 50 DQ13
VSSQ 6 49 VDDQ
1.7 3.4 DQ3 7 48 DQ12
DQ4 8 47 DQ11
VDDQ 9

IC205
46 VSSQ
0 0 1.7 0 DQ5 10 45 DQ10
DQ6 11 44 DQ9
VSSQ 12 43 VDDQ
0 3.4 1.7 3.3 DQ7 13 42 DQ8
VDD 14 41 VSS
to DSP 4/6 LDQM 15 40 N.C/RFU
0
6 0 1.6 3.4 WE
CAS
RAS
16
17
18
39
38
37
UDQM
CLK
CKE
0 1.6 1.6 0 CS 19 36 N.C
BA0 20 35
to DSP 5/6 0.9 0.3 1.6 0
BA1
A10/AP
21
22
34
33
A11
A9
A8
to DSP 3/6, 4/6, 6/6 A0
A1
23
24
32
31
A7
A6
0.9 1.6 1.6 0 A2 25 30 A5
IC201

A3 26 29 A4
VDD 27 28 VSS
2.1 0.3 1.6 0.5
2.1 1.6 0 3.4

0 0.3 to DSP 4/6

to DSP 1/6 1.6

0.3

3.4 3.4 to DSP 5/6

1.6

0.3
0.3 3.4 to DSP 5/6
7 3.5 1.7
0.3 1.4
0.2 0.3

IC206
0.3 1.4
0.2 1.7

2.0 0.3
0.3 0.8
to DSP 3/6, 4/6
0.3 0.8
1.8 1.7
0.3 5.0
1.9 0.3 IC203: SN74AHC02PWR
0.3 3.4
1.9 3.4 Quadruple 2-input positive-NOR gates
0.3 0.2
1.9 0
0.3 0
1.9 3.5 1Y 1 14 Vcc
0 3.4 1A 2 13 4Y
3.3 0.2
to DSP 4/6 1B 3 12 4B

2Y 4 11 4A

2A 5 10 3Y
8 to DSP 5/6 2B 6 9 3B

GND 7 8 3A

FLASH ROM

IC204-206: SN74LV573APWR
Octal transparent D-type latches with 3-state outputs

9 OE
1

OE 1 20 VCC
11 1D 2 19
LE 1Q
2D 3 18 2Q
C1 19
2 1Q 3D 4 17 3Q
1D 1D
4D 5 16 4Q
5D 6 15 5Q
6D 7 14 6Q
7D 8 13 7Q
8D 9 12 8Q
C8 12 GND 10 11 LE
9 8Q
8D 8D

10
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

74
 A B C D E F G H I J K L M N

RX-V363/HTR-6130

DSP 3/6
1

2 IC301: AK4588VQ
2/8-channel audio CODEC with DIR
PVSS PVDD R XTI XTO

RX0 X'tal
RX1 Clock Oscillator
RX2 8 to 3 Recovery Clock MCKO1
RX3 Input Generator MCKO2
RX4
Selector
RX5 DEM
RX6
DAIF LRCK2
RX7 Audio
BICK2
Decoder I/F
SDTO2
TX0
DAUX2
PDN

TX1
I2C
AVDD DIT
AVSS
DVDD CSN
3 DIGITAL IN
DVSS AC-3/MPEG
Error &
STAT US
Q-subcode
buffer
uP I/F
CCLK
CDTO
TVDD Detect Detect CDTI
VIN
5.0
B,C,U, INT0
IC305 4.4 INT1
VOUT
2.5 2.0 LIN ADC HPF
IC305 Audio
I/F
RIN ADC HPF

0
DVD LOUT1 LPF DAC DATT
DEM
(U, C, R, T, K, A, MCLK

0
MCLK
LRCK LRCK1
B, G, E, F, L models) LPF DAC DATT

3.4

4.9

1.7

4.9
ROUT1

0
4.9
BICK BICK1

2.5

0.4
DEM
IC305 IC305 IC305 IC305

1.3
LPF DAC DATT DAUX1
LOUT2
DEM
0
3.9 DIGITAL IN ROUT2 LPF DAC DATT Format
3.9 DEM Converter
0
3.4
4 4.9
5.0
4.4 LOUT3 LPF DAC DATT
DEM
SDOUT

0 0 ANALOG L LPF DAC DATT SDTO1

ROUT3
2.6 4.9 DEM SDIN1 SDTI1
SDIN2 SDTI2
2.3 4.9 SDIN3
LPF DAC DATT SDTI3
LOUT4
0 B-1 2.5 DEM SDIN4 SDTI4

2.5 LPF DAC DATT

ROUT4
0.4 2.5
DEM
1.7

0
IC301
2.5
to DSP 5/6

DAU X2

TEST2
4.9

MCLK

PVDD
CAD1

CAD0

PVSS
INT0

RX7

RX6

RX5

RX4

RX3

RX2
TX1
TX0

VIN

I2C

NC
R
0.2 2.5
CD DIGITAL IN

78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
80
79
1.7
(U, C, R, T, K, A, INT1 1 60 TEST1
1.8 2.5 2 59 RX1
B, G, E, F, L models) BOUT
58 NC

CODEC with DIR

TVDD 3
1.4 4 57 RX0
FL DVDD
DVSS 5 56 AVSS

5 2.5 XTO
XTI
6
7
55
54
53
AVDD
VREFH
VCOM
1.8 TEST3 8
MCKO2 9 52 RIN
0.4 2.5 MCKO1 10 51 LIN
COUT 11 50 NC
UOUT 12 49 ROUT1
ANALOG L AD IN SL VOUT 13 48
47
NC
LOUT1
SDTO2 14
BICK2 15 46 NC
LRCK2 16 45 ROUT2
44 NC
SW SDTO1 17

3.4

0.2

0.2

1.3

4.9

3.4

2.5
BICK1 18 43 LOUT2
42 NC

0
LRCK1 19

3.3

3.4
CDTO 20 41 ROUT3

21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
C

CCLK/SCL

DZF2
DZF1
CSN
DAUX1
SDTI4
SDTI3
SDTI2
SDTI1
XTL1
XTL0
PDN
MASTER

ROUT4
LOUT4

LOUT3
CDTI/SDA

NC

NC

NC
to DSP 5/6
to DSP 5/6

IC305: SN74LVU04APWR
Hex inverters

to DSP 1/6, 2/6 A1 1 14 VCC

Y1 2 13 A6

to DSP 2/6 A2 3 12 Y6

Y2 4 11 A5

A3 5 10 Y5
to DSP 5/6
7 Y3 6 9 A4

GND 7 8 Y4

IC307
R, T, K, A, B, G, E, F, L models

8
POINT B-1 XL301 (Pin 6 of IC301)
DIGITAL OUT

to DSP 1/6

to DSP 1/6
MICRO-
PROCESSOR
to DSP 1/6
9

10
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

75
 A B C D E F G H I J K L M N
RX-V363/HTR-6130

1
DSP 4/6

to DSP 2/6

* Destination for A/D port

R406 [ohm] 1.5 k 3.3 k 4.7 k 6.8 k 8.2 k
R407 [ohm] 8.2 k 6.8 k 5.6 k 3.9 k 2.2 k
DEST (1 pin) [V] 2.6-3.0 2.0-2.4 1.6-2.0 1.0-1.4 0.5-0.9
A/D value (3.3 V=255) 206-226 162-182 129-149 83-103 44-64
Destination U, C R, L T K, A B, G, E, F
3
3.3 0
A/D SELECTOR
1.7 0
to DSP 5/6 3.3 0

3.4 3.4 0.9

3.3 0
1.8
3.4 3.3

IC402
3.3 1.2

3.4 3.3

4
0.8 to DSP 5/6

to DSP 6/6

A/D SELECTOR
5 0

0.2

0
B, G, E, F models

1.7 3.3 0
4ch ADC
1.7 0
IC401

0
3.3 0 3.4 3.3 to DSP 5/6 to DSP 5/6
3.4
3.4 3.4 0.6

0.8 5.1 0 3.3

6 to DSP 5/6 1.7
1.8
0.2 3.4
IC403

1.1 3.4 1.7 3.3

2.9 *
3.4

IC402, 403: SN74LV4051APWR

8-channel analog multiplxers/demultiplexers

3
COM

13
Y0

14
7 A
11 Y1

1 16
INPUTS ON
15 Y4 VCC
Y2 INH C B A CHANNEL
Y6 2 15 Y2
COM 3 14 L L L L Y0
Y1
12 L L L H Y1
10 Y3 Y7 4 13 Y0
Page 79 F10 to DSP 2/6 B

1
Y5
INH
5
6
12
11
Y3
L
L
L
L
H
H
L
H
Y2
Y3
Y4 A
to OPERATION (1)_CB202 10
L H L L Y4
GND 7 B
8 9 L H L H Y5
5 GND C
9 Y5 L H H L Y6
C
to DSP 2/6 2
Y6
L H H H Y7
H X X X None

4
6 Y7
INH

CB408
8 IC404: SN74AHCT245PWR
0.6

to DSP 1/6 Octal bus transceivers with 3-state outputs

0
1
DIR DIR 1 20 VCC
5.0 A1 2 19 OE
0 19
OE
0.6 3.4
A2 3 18 B1
2 A3 4 17 B2
IC404

3.4 3.4 A1
0.6
A4 5 16 B3
0.2 0 to DSP 5/6 18
B1
A5 6 15 B4
A6 7 14 B5
5.0 0.2
A7 8 13 B6
5.0 3.3
9 0.2 3.3
To Seven Other Channels A8 9 12 B7
GND 10 11 B8
5.0 0.5

to DSP 5/6 BUS SWITCH to DSP 1/6, 2/6 IC401: ADC084S021 CIMM
4-channel, 200 ksps, 8-bit A/D converter

IN1

IN2 8-Bit VA
SUCCESSIVE CS 1 10 SCLK
IN3 MUX T/H
APPROXIMATION VA 2 9 DOUT
GND
ADC
GND 3 ADC084S021 8 DIN
IN4 GND
10 IN4 4 7 IN1
IN3 5 6 IN2
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced SCLK
with parts having specifications equal to those originally installed. CONTROL CS
★ Schematic diagram is subject to change without notice. LOGIC DIN
DOUT

76
 A B C D E F G H I J K L M N

RX-V363/HTR-6130

DSP 5/6
1

CB512

to DSP 1/6

2
to DSP 2/6

to DSP 2/6

to DSP 1/6, 2/6, 4/6

Page 82 D10 0
3.4
to MAIN (5)_CB161
3

CB501
3.4 3.4

to DSP 1/6-4/6
Page 81 A5
to MAIN (1)_CB101

4 FL
CB502
to DSP 3/6
SL
SW to DSP 3/6
C

ANALOG L
to DSP 1/6-4/6
to DSP 3/6
Page 82 F4
5 to MAIN (5)_CB164

to DSP 4/6
to DSP 6/6
3.4
4.9
IC501
3.4
3.4
4.9
IC501
3.4
0.8
0
IC501
0.8
1.3
0
IC501
1.3
to OPERATION (4)_CB182

6
IC501: SN74AHCT08PWR
(U, C models)
K3

Quadruple 2-input positive-AND gates

Page 80

1A 1 14 Vcc

1B 2 13 4B

1Y 3 12 4A

2A 4 11 4Y
CB504
2B 5 10 3B

CB516 2Y 6 9 3A

GND 7 8 3Y
7 A B
to DSP 4/6 3.4
IC505
3.4
3.4
IC505
3.4 to DSP 1/6

IC505: SN74LV08APWR
Quadruple 2-input positive-AND gate

Page 80 A7
C 1A 1 14 Vcc
to OPERATION (2)_CB232
3.4
1B 2 13 4B
3.4 3.4
IC505 3.4 IC505 3.4
0
1Y 3 12 4A

2A 4 11 4Y

to DSP 6/6 to DSP 2/6 2B 5 10 3B

8 2Y 6 9 3A

GND 7 8 3Y

9
POINT A / EX3.3, B / Pin 8 of IC505, C / J504

EX3.3 A EX3.3 A

IC505 8 pin B IC505 8 pin B

(/DRESET) (/DRESET)

J504 C J504 C
(/RESET) (/RESET)

10
Power cable ON Power cable OFF Power cable ON
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

77
 A B C D E F G H I J K L M N
RX-V363/HTR-6130

1
DSP 6/6

(U, C models)
to DSP 1/6

to DSP 1/6
3

0.4 3.3
to DSP 4/6

CB602
No replacement part available.
to DSP 1/6
4

DOCK
to DSP 5/6

to DSP 5/6
5

B, G, E, F models

to DSP 5/6 to DSP 5/6

to DSP 5/6
to DSP 4/6

to DSP 1/6

to DSP 2/6

B, G, E, F models

10
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

78
 A B C D E F G H I J K L M N

RX-V363/HTR-6130

OPERATION 1/2
1

-24.4

-24.4

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.4

-29.3

-29.4

-31.6

-29.6

-23.8

-23.7

-21.8

-23.7

-25.7

-23.7

-29.5

-25.5

-31.6

-21.7

-23.7

-29.5

-21.7

-29.6

-21.8

-23.7

-23.7

-16.1

-23.5

-21.8

-23.7

-29.6

-25.4

-27.6

-19.7

-23.6

-29.5

-25.5

-27.5

-21.6

-21.8

-17.9

-18.1

-19.9

-19.4

-24.4

-24.4
3.3

-21.7

-29.6

-21.8

-23.7

-23.7

-16.2

-23.5

-21.8

-23.7

-29.6

-25.4

-27.6

-19.7

-23.6

3.3
-19.4
3
-19.4

-25.5
-29.5 -25.5

-23.7 -27.5

-21.7 -21.6 -24.9

-31.6 -21.8

-25.5 VFD -17.9

-29.5 -18.1

-23.7 -19.9
-28.4
-25.7
IC201
-19.4
IC201: M66003-0131FP-R

3.3

3.3
-23.7 3.3
18 digit 5 x 7 segment VFD controller/driver
4 -21.8 1.5
3.3

3.3 1.5
-23.7 Display code
RAM CGROM
OPERATION (6) -23.8 0
-16.2 -31.9 (8-bit x 60) (35 bit x 166) 44 SEG00

Code Segment 19 SEG25

write output 17 SEG26
-29.7 -29.6 3.2 -16.1 circuit
dot data
CGROM 9 SEG34
CS 2 Serial data (35 bit x 16)
-29.4 -31.6 3.2 receive write
SCK 3 Code/
3.3 SDATA 4 circuit
3.3 3.3 command
control 45 SEG35
JK261 -29.7
circuit
3.3 DIG11/
-29.8 52
SEG42
-29.7
DIG12/
-29.7 51
SEG41
code Segment/
CB261 50 DIG13/
select Digit SEG40
to MAIN (1)_W103

-29.5 -29.3 select/ DIG14/

49
XIN 7 Clock output SEG39

-29.8
timing Display
I4

3.3 generator clock controller scan pulse circuit DIG15/

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-29.7

-31.8
XOUT 6 48
SEG38
DIG16/
W2004 47
SEG37
5
Page 81

0 CB203 46 DIG17/
SEG36

63 DIG00
Digit
RESET 1 output
Page 80 F9 Vcc1 8 circuit
53 DIG10
Vcc2 18
to OPERATION (2)_CB235 Vss 5

0 0 Vp 64

0
0 0
3.3 3.3

3.3
IC202: NJM4565M
Dual operational amplifier
0
OPERATION (10)
-1.3 3.2
V+
6 0 8

W2003
CB204 0
CB274
0 2, 6
-1.3 3.2 3.2 –INPUT OUTPUT
3.3 +INPUT 1, 7
3, 5
0 0
0
3.2

-1.3 -1.3 3.2

V–
4

2.4 2.4 2.4

OPERATION (11) 2.4

7 2.4

0
0

OPERATION (7)

VIDEO
Page 82 J4
JK201 to MAIN (4)_CB192

TUNING
AUTO/MAN’L

8 0

0
VIDEO
0
IC202 AUX
0

W2351 0 0
AUDIO
0
0

IC202 0
0

9 0
0

0 0
JK266

JK266 PORTABLE
OPERATION (1)
CB202
W2001

10
Page 82 I4 Page 76 C7
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
to MAIN (4)_CB191 to DSP_CB408
★ Components having special characteristics are marked s and must be replaced
(R, K, A, B, G, E, F, L models)
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

79
 A B C D E F G H I J K L M N
RX-V363/HTR-6130

1
OPERATION 2/2
COMPONENT VIDEO VIDEO

MONITOR OUT DVR DTV/CBL DVD

0 -4.8
4.9 0

4.9

4.9
5.0
0
0
0
0

0
4.9 Page 82 J4
0 0
to MAIN (4)_CB193
0 4.9

RDS 3.6 0
W181

IC183
0
5.0
IC181
5.0 0

3 CB182
3.6

0
0

-4.8

0
-4.8
0

0
5.0
0
2.2
0
0

Page 77 A6
-4.9 to DSP_CB504
0
(U, C models)
-5.6
-5.5 -11.1

OPERATION (4)
0
4 0.7
0 0

-11.9

-11.9
0 0.7

5.0
0.1
0.1
0
0
CB181

W182
Page 82 E3 Page 83 M7
to MAIN (5)_W161 to HDMI_CB904 OPERATION (5)
OPERATION (2)
R, L models
3.3

5
3.7
3.3
3.3

0 3.7
0 3.3 3.3 0 3.7 CB258
3.3 9.7 9.6 9.6 AC 9.3
0 0

To POWER TRANSFORMER
IC238
7.2 0 1.0
0
0 0 0 1.2 3.7 3.7
3.7
0

3.7 3.7
CB251 1.2
9.5 CB256
3.2
9.5 8.8 8.8 9.5 AC IN
IC232 7.2 1.8 0 0
CB231 9.5
6 W2251
0 1.0
4.2 4.5

To POWER TRANSFORMER
8.8
3.3
0

0
CB257
CB232
1.7
CB252 CB254
1.7

0
to DSP_CB516
B7

0
Page 77

IC233
IC236
18.4
OPERATION (3)
18.4
5.0 18.4
11.9 -0.1
7 0 -0.1
0

-19.2 CB234
To POWER TRANSFORMER

AC29.9
W2152

CB233
to MAIN (1)_CB103

AC8.5
I6

-11.9 AC10.3
-19.2
Page 81

IC237 AC9.7

W2153 12.5 AC5.1

8 5.3 12.5 5.2

W2154 0 5.5
to HDMI_CB905

0
I6

0
Page 83

IC183: NJM2595M (TE1)

5-input 3-output video switch
to OPERATION (1)_CB203

V+ SW2 SW1 SW5

CB235 16 10 14 2
J5

Vin1 13

S5
S1
Vin2 9
6dB 75Ω
20k 1 Vout1
Page 79

Amp Driver
20k
S2
11.4 Vin3 7
20k S4 S6
6dB 75Ω Vout1 1 16 V+
Vin4 5 Amp Driver 15 Vout2
4.5 11.4 SW5 2 15 Vout2
0 4.4 20k S3 20k Vin5 3 14 SW1
9 4.8
Vin5 3
20k S7
SW3
Vin4
4

5
13

12
Vin1
GND

6dB 75Ω
SW4 6 11 Vout3
Amp Driver 11 Vout3
0 Vin3 7 10 SW2
20k V- 8 9 Vin2

4 6 12 8
SW5 SW4 GND V-

IC181: NJM2586AM
Wide band 3-input 1-output 3-circuit video amplifier IC233, 234, 239: KIA7805API IC237: KIA7912PI IC238: LM61CIZ
Voltage regulator Voltage regulator Temperature sensor
6dB 75
CH1 IN1 1 24 CH1 OUT
Amp Driver
1 INPUT 1 COMMON (GND)
IC236: KIA7812API Bias
Cont1 R22 R17 R23
R22
SW 1 2 23 PS R15 R18 R21 R23
Voltage regulator Cont2 Cont1
1 INPUT IC232: NJM2388F33 CH1 IN2 3
6dB
Amp
75
Driver 22 CH2 OUT
R1 Q11 Q11-1 Q28 Q17 Q21
Q15 Q22 Q24
R22 R17 R23
Low dropout voltage regulator with ON/OFF control SW 2 4
Bias
21 V +2 Q16 R16 Q23 R13 R12
R1 Q11 Q11-1 Cont1 Q12
Q19 R24
6dB 75 Q14 R14 Q29
Q15 Vin 1 2 CH1 IN3 5 Driver 20 CH3 OUT R10 R15
Vout Amp R20
Q16 Bias Q17 Q19 R1
R16 Q18 Q20
Q12 GND GND R19 Q25
6 19
Q14 R14 R12 3 OUTPUT
10 Q17
R19
Q19
R10 R15
R16
+
V 1 7 18 V-2
Q18
Q1
Q6 R20
Q30 R14 R17
R19
Q31 R25
R12 3 OUTPUT
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
R18
Q18 R20 Bandgap CH2 IN1 8 17 CH3 IN1 R11 R9 Q12 Q13
Q1
Q6
Reference + Z1 R7 C1 Q2 Q3 R11
★ Components having special characteristics are marked s and must be replaced - Bias Bias Q26-1 R10
R18 R2 Q10 R26
R11 R9 GND 9 16 V-1 Q26 Q27 3 OUTPUT
R7 C1 ON/OFF Q2 Q27-1
Z1 R21 Q7 Q14
with parts having specifications equal to those originally installed. Q2
R2 Q10 Cont 4 control
CH2 IN2 10 15 CH3 IN2 Q13 R3 Q7
R0
D4
Q15
Cont2 Cont2
★ Schematic diagram is subject to change without notice. R21 Bias
Q4 C2 C1 Q16
R3 Q7 Bias R9
Q13 Over Voltage Thermal Over Current Q8
GND 11 14 GND Q3 Q5 Q9 Q8 R4 R5 R6
Q4 Protection Protection Protection R13 Q4 Q6 Q9 Q11
Q3 Q5 Q9 Q8 R4 R3
R13 CH2 IN3 12 13 CH3 IN3 R5 R6 R8 Q5 Q10
GND 3 R2 R8
R4 R5 R6 R8
Bias Bias 2 COMMON (GND) R7
2 INPUT
2 COMMON (GND)

80
 A B C D E F G H I J K L M N

RX-V363/HTR-6130

MAIN 1/2
1

POWER AMPLIFIER
IC102

51.4
5.16

-50.8

0.5
-52.1
51.9
0
0
0

0
0
0
0

0
0
0 FRONT L
51.8
0
SURROUND L SPEAKERS
2 -11.9 0
FRONT A
L/R
51.6

-11.9 0
W101A

3
5.0

3.3

3.3

-12.0
51.6

to MAIN 2/2
W103
0

to OPERATION (6)_CB261
4

A5
3.3 0 0
MAIN (3)
0

Page 79
3.3 5.0 0 0
0
-12.0
0 3.4

0
0

POWER AMPLIFIER W101B

IC101
L
FRONT B
-50.8

51.4
-52.1
51.9
0
0
0
0

0
0
0
0
1.6

0
0
0
0
0
0

R
0 0 0 SURROUND L
CB101 0 0 0 CENTER
5 W102A W102B CENTER SPEAKERS
to DSP_CB501
B3

0
51.6 L
Page 77

-11.9 0
SURROUND
0 R
0

to OPERATION (2)_CB233
0 CB103

A8
-11.9 0
0
to MAIN 2/2

Page 80
0 11.9
6 IC101: STK433-330-E
3-channel AF power amplifier, stand-by circuit built-in
11.8
FRONT L 11.8
to MAIN 2/2
3
0.2
-12.0
51.6
CENTER 8
0
-12.1
0 Pre Pre Pre
0 to MAIN 2/2
Driver Driver Driver
CH1 CH2 CH3
0
MONO IC
3.3 3.4 11 + + +
11.9 11.9 12 – – –
3.3 0

7 -12.0
0 0
11.9

11.7
-12.0
0 to MAIN 2/2
11.7 -12.0
11.9

0 51.6 Bias Circuit

-12.1 -12.1 0.2
-11.9 1
0 2
0 0
0
SUB
9 5 4 6 7 10 13 14151617 19 18
11.7 11.7

0 to MAIN 2/2
0 0
8 0 11.6
0
51.6 11.6

3.3 IC102: STK433-130-E

51.6
2-channel AF power amplifier, stand-by circuit built-in
11.6 0
50.9 11.6

51.6 3
-12.1 -12.1
4.4
3.4 LIM [V]
8
51.6
2.7 2.7
11.9

Pre Driver Pre Driver

CH1 CH2
11.8 11.9
-31.8
to MAIN 2/2 11.9 11 15
+ +
50.7 -51.6
9 0.2
12 – – 14
-35.7
-51.3 -32.5
0
-11.9

51.8

-32.5

Bias Circuit
51.8
0 1
0
0.4 0.4 AC61.9
0
2
-51.9 -41.3
52.0 CB104
0 0 SUB
-41.3 10 9 5 4 6 7 13
0 0

To POWER TRANSFORMER
10
High Low (U, C models) Low (R, T, K, A, B, G, E, F, L models)

LIM [V] (A/D 3.3V=255) +3.0 to +3.3 (255) +1.20 to +1.35 (102) +1.00 to +1.20 (90) ★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
+46.0 to +52.0 (8-ohms) AC76.5 ★ Components having special characteristics are marked s and must be replaced
+BV [V] +20.0 to +23.0 (8-ohms/6-ohms) +18.0 to +21.0 (8-ohms/6-ohms)
+33.0 to +36.0 (6-ohms) with parts having specifications equal to those originally installed.
MAIN (1) -BV [V]
-52.0 to -46.0 (8-ohms)
-25.0 to -23.0 (8-ohms/6-ohms) -22.0 to -19.0 (8-ohms/6-ohms) ★ Schematic diagram is subject to change without notice.
-36.0 to -33.0 (6-ohms)

81
 A B C D E F G H I J K L M N
RX-V363/HTR-6130

1
MAIN 2/2

IC161: R2A15218FP
8-channel electronic volume with 11 input selector and tone control

BASSR2

BASSR1
SBRCIN
SBLCIN

SBRIN2
CLOCK

SBLIN2
SWIN2
DGND

SRIN2
FRIN2
SUBR

SLIN2
FLIN2

TRER
SUBL
DATA

CIN2

N.C.

N.C.
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
A VCC
FRONT MUTE 51 30 A VCC
MCU
2 A VEE 52 I/F 29 N.C.
A VEE
N.C. 53 28 TREL
0/-6/-12/-18dB
ADCL 54 27 BASSL2
ATT
ADCR 55 26 BASSL1
AGND 56 Bass/Treble 25 N.C.
0~-95dB, -14~+14dB
MAIN -∞ (2dBstep) +42~0dB
N.C. 57 SUB (0.5dBstep) Bypass (0.5dBstep) 24 FRC
SURROUND

MAIN
MAIN
Tone+MIX Tone
INR1 58 Tone 23 FROUT
MULTI CH
INL1 59 +42~0dB 22 A GND
INPUT (0.5dBstep)

INR2 60 Tone 21 FLOUT

Tone+MIX Tone

SUB
INL2 61 Bass/Treble Bypass 20 FLC
0~95dB,
-∞ -14~+14dB
(0.5dBstep) (2dBstep)
Page 77 B5 INR3 62 19 A GND
CENTER
3

SUB
to DSP_CB502

CMIX
INL3 63 18 CC
+42~-95dB
-∞ (0.5dBstep)
INR4 64 17 COUT

SWMIX
INL4 65 16 A GND
Page 80 G4 INR5 66
+42~-95dB
-∞ (0.5dBstep) 15 SWOUT

CB164
W161
to OPERATION (4)_CB181

W162
+42~-95dB
SUBWOOFER W163A
INL5 67
-∞ (0.5dBstep)
14 SWC

CB181
INR6 68 13 N.C.
INL6 69 +42~-95dB 12 SRC
-∞ (0.5dBstep)

Page 79 K8 INR7 70 11 SROUT

to OPERATION (7)_W2351 INL7 71 10 A GND
+42~-95dB
Page 79 D10
11.7
FILTER to OPERATION (1)_W2001 Page 80 K3
to OPERATION (4)_W181
INR8 72
-∞ (0.5dBstep)
9 SLOUT
0
0 IC162
0 (R, K, A, B, G, E, F, L models) INL8 73 8 SLC

CB192
CB191

CB193
4 0 N.C. 74 +42~-95dB 7 A GND
-∞ (0.5dBstep)
DTV/CBL ANALOG L 0 FL INRA/RECR1 75 6 SBRC
0 0 IC162 0
-12.1
REC
3.3
11.8 7.1
INLA/RECL1 76 5 SBR OUT
3.3
N.C. 77 4 A GND
7.8 W163B
-12.0
INR9 78 3 SBL OUT

INL9 79 2 SBLC
0 0
7.8 11.7
0
0
IC163 N.C. 80 1 N.C.
0

0
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
SL

N.C.

N.C.

N.C.

N.C.
RECR3

RECL3

FLIN1

FRIN1

CIN1

SWIN1

SLIN1

SRIN1

SBLIN1

SBRIN1
INRB/RECR2

INLB/RECL2

INR10/RECR4

INL10/RECL4

INR11/RECR5

INL11/RECL5
ANALOG IN 0
IC163
0
0 -12.1
-7.8

5 -7.8

0
-12.1 -7.1 11.7
0 C MAIN (4)
IC164

(B)
0

AUDIO
0 0 0
SW IC162-164, 169: NJM4565M
0 IC164
-12.1 Dual operational amplifier

V+
8
0

0
0

0
0

0
0

0
0

0
0

0
2, 6
0

0
0
7.1 –INPUT OUTPUT
+INPUT 1, 7
6 0
-7.1 0
3, 5
0 0
FRONT L
0 0
0 0

0
SELECTOR 0

to MAIN 1/2
0 0 V–

0
0
0 and 0

0
4

VOLUME
0 0
0 0
SUB
0 0 WOOFER
0 0 0
IC168: LC72725KM
0 0
RDS signal demodulation IC
IC161

0 0
-12.1 11.7
0 0

0 0 11.2
0 IC169 IC169
0 11.2
0 0 0 0
+3V VREF FLOUT CIN +3V
0 0
0 Vdda
7 0
0
0
0 CENTER PLL
CLOCK
RECOVERY
Vddd

REFERENCE (57kHz)
0 0 (1187.5Hz)
VOLTAGE
0 0 Vssa Vssd
VREF
0 0 0
57kHz
0
MPXIN ANTIALIASING BPF SMOOTHING DATA RDDA
0
FILTER (SCF) FILTER DECODER
0 0
RDCL
IN 0
0 SURROUND L
RAM
0 0
(128bits) MODE
0

RST
0

0
0

CLK(4.332MHz)
0

0
0

RDS-ID RDS-ID/
0

TEST TEST
0 OSC DETECT READY
0
0
0

0
0

XIN XOUT
8 OUT

0 0 0

OUTPUT -12.0 -12.0

0 0

-12.0 9.4 11.8

IC168

10.1
9
to MAIN 1/2
10.2

MAIN (5)
CB163
CB161

Page 77 B2
To TUNER
10 to DSP_CB512
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

82
 A B C D E F G H I J K L M N

RX-V363/HTR-6130

HDMI
1

HDMI
OUT DVD DTV/CBL

CB901 CB903 CB903

3
1.4 0 1.2 0

0 0 0 0

0 0 0
0 0 0 0 0

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0
0 0

4 0 1.0

0 0

0 0
0 0

0 0
IC902 0
0
0
0
0 5.3
5.3
0
0
5 0

0
0.8

0 3.3
1.4 0

3.3
3.3
3.3

3.3
3.3

0
1.2

0
0

3.3
0
1.0 0
0 0
0 0
0 0
6 3.3 3.3
0 0
0 0
0 0
0 0
IC907
0 0
0 IC903 0
0 0 3.3 0

0 0
0 0
0 0

3.3 3.3
0 0 3.3

IC908

0
0 0
3.3 0 CB904
Page 80 I4
0 0

0
0

0
0

3.3
3.3

0
0

0
0
IC908
0
to OPERATION (4)_W182

7 3.3

3.3

IC906
0
0 0

CB905
Page 80 A8
to OPERATION (2)_W2154

5.3 3.3

3.3 IC905
0
0
IC904 5.3 3.3 3.3

8 0
0

IC903: CXB1442AR-T4
Cable equalizer with 2-system switching function IC904: SN74LVC3G04DCTR IC905: NJM2885DL1-33 IC907: SN74CB3Q3257PWR IC908: SN74LVC2G17DCKR
Triple inverter gate Low dropout voltage regulator Low boltage high-bandwidth bus switch Dual schmitt-trigger buffer
n= 0, 1, 2
1A 4 SW 2 1B1
VIN 1 3 VOUT
Input switching 1A 1 8 VCC
Termination circuit SW 3 1B2 1A 1 6 1Y
9 ADTnP
resistor
Thermal 2A 7 SW 5 2B1
GND 2 5 VCC
Quantizer 3Y 2 7 1Y Protection
ADTnN Output buffer SW 6 2B2
YDTnP
Bandgap 2A 3 4 2Y
Equalizer
2A 3 6 3A
Reference 3A 9 SW 11 3B1
YDTnN

SW 10 3B2
Output
Termination GND 4 5 2Y
4A 12 SW 14 4B1
BDTnP Detector
BDTnN SW 13 4B2
GND 2 S 1 16 VCC
1B1 2 15 OE
EQ outputs
1B2 3 14 4B1
EQ inputs 1A 4 13 4B2
IC902: NJM2867F3-05 S 1 2B1 5 12 4A
Input switching
Low dropout voltage regulator 2B2 6 11 3B1
ADT1N

ADT0N
ADT1P

ADT0P

circuit
ACKN
ACKP

3B2
GND

GND

2A 7 10
SEL

ACKP
Vcc

Vcc
CE

OE 15
GND 8 9 3A
ACKN Quantizer 36 35 34 33 32 31 30 29 28 27 26 25
VIN 5 Output buffer
4 VOUT
YCKP Vcc 37 24 YCKN
Equalizer
Vcc 38 23 YCKP
YCKN
Control 1
10 Thermal
Protection
ADT2N 39
ADT2P 40
22 GND
21 YDT0N IC906: SN74LVC1G08DCKR
Output
GND 41 20 YDT0P
Bandgap BCKP
Termination
Detector Vcc 42 19 Vcc
Single 2-input positive-AND gate
Reference
BCKN
Output Current
Vcc 43 18 Vcc ★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
Clock
Detector Control Circuit REXT
GND 44 17 YDT1N
★ Components having special characteristics are marked s and must be replaced
BCKN 45 16 YDT1P
BCKP 46 15 GND A 1 5 VCC with parts having specifications equal to those originally installed.
Vcc 47 14 YDT2N
B 2 ★ Schematic diagram is subject to change without notice.
Vcc 48 13 YDT2P
GND 2 GND 3 4 Y
SEL 1 2 3 4 5 6 7 8 9 10 11 12
CMOS inputs Control Logic
TEST
Vcc
BDT0N
BDT0P
GND

Vcc
BDT1N
BDT1P
GND
BDT2N
BDT2P

REXT

CE
83
 RX-V363/HTR-6130

■ REPLACEMENT PARTS LIST

• ELECTRICAL COMPONENT PARTS
WARNING
● Components having special characteristics are marked s and must be replaced with parts having specifications
equal to those originally installed.
● The chip resistor is not supplied as a replacement part.
* When a chip resistor is necessary, use the following part.
AAX60720: CHIP RESISTOR SAMPLE BOOK

ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:

C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE
C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED,INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR,RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER

RX-V363/HTR-6130
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN,TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR. : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.CEMENT : CEMENT RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TIGHT SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CN.BS.PIN : CONNECTOR,BASE PIN SCR.CUP : CUP TIGHT SCREW
CN.CANNON : CONNECTOR,CANNON SCR.TERM : SCREW TERMINAL
CN.DIN : CONNECTOR,DIN SCR.TR : SCREW,TRANSISTOR
CN.FLAT : CONNECTOR,FLAT CABLE SUPRT.PCB : SUPPORT,P.C.B.
CN.POST : CONNECTOR,BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL,AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL,FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL,FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL,FM MIX SW.MICRO : MICRO SWITCH
COIL,OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASS’Y
FLTR.LC.RF : LC FILTER,EMI TUNER.AM : TUNER PACK,AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK,FM
GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-ENDTUNER PACK
HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR
JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER,TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER

85
 RX-V363/HTR-6130

P.C.B. DSP and P.C.B. OPERATION

RX-V363/HTR-6130

✻ New Parts ✻ New Parts

86
 RX-V363/HTR-6130

P.C.B. OPERATION

RX-V363/HTR-6130
s

s
s
s
s

s
s
s

s
s

✻ New Parts ✻ New Parts

87
 RX-V363/HTR-6130

P.C.B. OPERATION and P.C.B. MAIN

s
s
RX-V363/HTR-6130

s
s
s

s
s

s s
s

s
s
s
s

✻ New Parts ✻ New Parts

88
 RX-V363/HTR-6130

P.C.B. MAIN

s
s

RX-V363/HTR-6130
s
s
s
s
s
s
s
s
s

s
s
s
s
s
s
s
s

s
s
s
s
s

✻ New Parts ✻ New Parts

89
 RX-V363/HTR-6130

P.C.B. HDMI
RX-V363/HTR-6130

✻ New Parts ✻ New Parts

90
 RX-V363/HTR-6130

Carbon Resistors
Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No.
1.0 Ω HJ35 3100 HF85 3100 10 kΩ HF45 7100 HF45 7100
1.8 Ω HJ35 3180 ❊ 11 kΩ HF45 7110 HF45 7110
2.2 Ω HJ35 3220 HF85 3220 12 kΩ HJ35 7120 HF85 7120
3.3 Ω HJ35 3330 HF85 3330 13 kΩ HF45 7130 HF45 7130
4.7 Ω HJ35 3470 HF85 3470 15 kΩ HF45 7150 HF45 7150
5.6 Ω HJ35 3560 HF85 3560 18 kΩ HF45 7180 HF45 7180
10 Ω HF45 4100 HF45 4100 22 kΩ HF45 7220 HF45 7220
15 Ω HJ35 4150 HF85 4150 24 kΩ HF45 7240 HF45 7240
22 Ω HF45 4220 HF45 4220 27 kΩ HJ35 7270 HF85 7270
27 Ω HJ35 4270 HF85 4270 30 kΩ HF45 7300 HF45 7300
33 Ω HF45 4330 HF45 4330 33 kΩ HF45 7330 HF45 7330
39 Ω HJ35 4470 HF85 4390 36 kΩ HF45 7360 HF45 7360
47 Ω HF45 4470 HF45 4470 39 kΩ HF45 7390 HF45 7390
56 Ω HF45 4560 HF45 4560 47 kΩ HF45 7470 HF45 7470
68 Ω HF45 4680 HF45 4680 51 kΩ HF45 7510 HF45 7510
75 Ω HF45 4750 HF45 4750 56 kΩ HF45 7560 HF45 7560
82 Ω HF45 4820 HF45 4820 62 kΩ HF45 7620 HF45 7620
91 Ω HF45 4910 HF45 4910 68 kΩ HF45 7680 HF45 7680
100 Ω HF45 5100 HF45 5100 82 kΩ HF45 7820 HF45 7820
110 Ω HJ35 5110 HF85 5110 91 kΩ HF45 7910 HF45 7910
120 Ω HF45 5120 HF45 5120 100 kΩ HF45 8100 HF45 8100
150 Ω HF45 5150 HF45 5150 110 kΩ HF45 8110 HF45 8110
160 Ω HJ35 5160 ❊ 120 kΩ HF45 8120 HF45 8120
180 Ω HF45 5180 HF45 5180 150 kΩ HF45 8150 HF45 8150
200 Ω HF45 5200 HF45 5200 180 kΩ HF45 8180 HF45 8180
220 Ω HF45 5220 HF45 5220 220 kΩ HJ35 8220 HF85 8220
270 Ω HF45 5270 HF45 5270 270 kΩ HF45 8270 HF45 8270
330 Ω HF45 5330 HF45 5330 300 kΩ HF45 8300 HF45 8300
390 Ω HF45 5390 HF45 5390 330 kΩ HF45 8330 HF45 8330
430 Ω HF45 5430 HF45 5430 390 kΩ HJ35 8390 HF85 8390
470 Ω HF45 5470 HF45 5470 470 kΩ HF45 8470 HF45 8470
510 Ω HF45 5510 HF45 5510 560 kΩ HJ35 8560 HF85 8560
560 Ω HF45 5560 HF45 5560 680 kΩ HJ35 8680 HF85 8680
680 Ω HF45 5680 HF45 5680 820 kΩ HJ35 8820 HF85 8820
820 Ω HF45 5820 HF45 5820 1.0 MΩ HF45 9100 HF45 9100
910 Ω HF45 5910 HF45 5910 1.2 MΩ HJ35 9120 ❊
1.0 kΩ HF45 6100 HF45 6100 1.5 MΩ HJ35 9150 HF85 9150
1.2 kΩ HF45 6120 HF45 6120 1.8 MΩ HJ35 9180 HF85 9180
1.5 kΩ HF45 6150 HF45 6150 2.2 MΩ HJ35 9220 HF85 9220
1.8 kΩ HF45 6180 HF45 6180 3.3 MΩ HJ35 9330 HF85 9330
2.0 kΩ HJ35 6200 HF85 6200 3.9 MΩ HJ35 9390 ❊
2.2 kΩ HF45 6220 HF45 6220 4.7 MΩ HJ35 9470 HF85 9470
2.4 kΩ HJ35 6240 HF85 6240
2.7 kΩ HF45 6270 HF45 6270
3.0 kΩ HF45 6300 HF45 6300
3.3 kΩ HF45 6330 HF45 6330
1/4W Type
HF45
3.6 kΩ HJ35 6360 HF85 6360
1/4W Type 1/6W Type
3.9 kΩ HF45 6390 HF45 6390
HJ35 HF85
4.7 kΩ HF45 6470 HF45 6470 10mm
5mm
5.1 kΩ HF45 6510 HF45 6510
5.6 kΩ HF45 6560 HF45 6560
6.8 kΩ HF45 6680 HF45 6680
8.2 kΩ HF45 6820 HF45 6820
9.1 kΩ HF45 6910 HF45 6910

❊ : Not available
91
 A B C D E F G H I J

RX-V363/HTR-6130

1
• OVERALL ASS’Y

200 201 R, K, A, B, G, E, F models

157 156
157
16
157

2 201-1 17
200-1
B, G, E, F models 160
160
171
202 U, C, R, T, L models
160

160
172
202 K, A, B, G, E, F models 2-9
3 160

2-1 (3)
160

203 101 6

12
171 103
4
204 168 24
168
167
15 170 167 2-8
170
R, L models
5 (4) 103
164
109

5 (3)
5 Front Panel Unit
151
163
AMP Unit
167 5 (5)
167

120
163

163 152

7 121
163
120 163

92
 A B C D E F G H I J

RX-V363/HTR-6130

s
s
s
s
s
s
3 s
s
s
s
s
s

7
✻ New Parts ✻ New Parts

93
 A B C D E F G H I J

RX-V363/HTR-6130

1
• FRONT PANEL UNIT

1-25

5 (10) 5 (1)
1-25
1-5 (6)
1-25
3

1-25
1-5 (5)
1-25 1-25
1-25

4 5 (6) 1-2

1-7 1-5 (1)

1-5 (2) 1-6

1-5 (4)
1-8
1-5 (3)

1-25

1-13 5 (7) 1-25

1-4
6 1-12

7
✻ New Parts

94
 A B C D E F G H I J

RX-V363/HTR-6130

1
• AMP UNIT

2-104 2-104 2-104

2-21

2-20

2-105 2-9 2-8

5 (2)
2

2-1 (1)

5 (11) 2-103

2-104

2-2
3

2-1 (4) 2-104

4
2-104

2-104

7
✻ New Parts

95
 A B C D E F G H I J

RX-V363/HTR-6130

1
■ REMOTE CONTROL
● RAV283 RX-V363 (U, C models), HTR-6130 (U, C models)
RAV284 RX-V363 (R, T, K, A, L models), HTR-6130 (R, T, K, A, L models)
• SCHEMATIC DIAGRAM • PANELS

RAV283 RAV284
+3V RX-V363 (U, C models) RX-V363 (R, T, K, A, L models)
2 HTR-6130 (U, C models) HTR-6130 (R, T, K, A, L models)

R3

100 ohms REW (SEARCH -) REC FF (SEARCH +) SKIP+ PLAY PAUSE SKIP- STOP

LEFT RETURN ENTER VOL down DISPLAY RIGHT DOWN

100 K-ohms

100 K-ohms

100 K-ohms
R5

R4
R6

1 2 4 3
3 J6
D1
IR Diode 5 9 6 8 ENTER +10 7 0
U1 J5
ZLR32300H2832G
11 7 TITLE SCENE UP SCENE VOL up SCENE MENU SCENE
P31 P07 1 4 3 2
J4
12 6
P32 P06
13 5 V-AUX/DOCK AMP D TV VOL - TV VOL + TV MUTE E TV INPUT
P33 P05
J3
14 4
P34 P04
4 15 23 DVD CD D-TV/CBL TV CH + TV CH - TUNER DVR MD/CD-R
P35 P03
Q1 J2
16 21
SMT P37 P02
R2 17 20
TV POWER A AV POWER MUTE POWER C STANDBY B
P36 P01
47 ohms J1
8 19
VDD P00
9 3
XTAL2 P27
10 2
X1 XTAL1 P26
8MHz 22 1
VSS P25
1 3
5 R1 C1 18
P30/Pref P24
28
1 ohm 47uF
24 27
P20 P23
2
25 26
P21 P22

RAV283 RAV284
6 J1 X X
J2 X X
J3 X X
J4 O X
J5 X O
J6 X X

96
 A B C D E F G H I J

RX-V363/HTR-6130

• KEY NO. LAYOUT • KEY CODE

Key Command
Label AMP
No. key
1 TV POWER – (TV POWER) (TV POWER) (TV POWER) (TV POWER) (TV POWER) TV POWER (TV POWER) (TV POWER) (TV POWER) TV POWER
1 2 3 4
2 AV POWER – (device) 79-60 7F-80 D1-1B 7C-80 (DVR POWER) 048.012 7F01-00 – (DVR POWER)
2 5 6 7 8
3 STANDBY O 7E-7F STANDBY
4 POWER O 7E-7E POWER
5 A O 7F01-3F A
9 10 11 12
6 B O 7A-B4 B
7 C O 7A-39 C
13 14 15 16 8 MUTE O 7A-1C MUTE
9 CD O 7A-15 CD
17 18 19 20 10 MD/CD-R O 7A-C9 MD/CD-R
11 TUNER O 7A-16 TUNER
21 22 23 24 12 TV CH + – (TV CH +) (TV CH +) (TV CH +) (TV CH +) (TV CH +) TV CH + (TV CH +) (TV CH +) (TV CH +) TV CH +
13 DVD O 7A-C1 DVD
14 D-TV/CBL O 7A-54 DTV/CBL
3
25 26 27 28 15 DVR O 7A-13 DVR
16 TV CH - – (TV CH -) (TV CH -) (TV CH -) (TV CH -) (TV CH -) TV CH - (TV CH -) (TV CH -) (TV CH -) TV CH -
17 V-AUX/DOCK O 7A-55 V-AUX (/DOCK)
29 31
30 32 18 D O 7A-0F VCR
19 E O 7A-14 PHONO
33 34 35 20 TV VOL + – (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +) TV VOL + (TV VOL +) (TV VOL +) (TV VOL +) TV VOL +
21 AMP O Enter into AMP mode
37 39
36 38 9 10 11 13 14 15 17 18 19
CD MD/CD-R TUNER DVD DTV/CBL DVR V-AUX/DOCK VCR PHONO
22 TV INPUT – (TV INPUT) (TV INPUT) (TV INPUT) (TV INPUT) (TV INPUT) TV INPUT (TV INPUT) (TV INPUT) (TV INPUT) TV INPUT
40 41 42 43 23 TV MUTE – (TV MUTE) (TV MUTE) (TV MUTE) (TV MUTE) (TV MUTE) TV MUTE (TV MUTE) (TV MUTE) (TV MUTE) TV MUTE
4 24 TV VOL - – (TV VOL -) (TV VOL -) (TV VOL -) (TV VOL -) (TV VOL -) TV VOL - (TV VOL -) (TV VOL -) (TV VOL -) TV VOL -
44 45 46 47 25 SCENE 1 O 7A-007F SCENE SELECT
26 SCENE 2 O 7A-037C SCENE SELECT
27 SCENE 3 O 7A-0679 SCENE SELECT
48 49 50 51 28 SCENE 4 O 7A-0976 SCENE SELECT
29 TITLE – 7A-86 – – 7A-AE 7C-B1 – 048.200 7F01-0D – –
52 53 54 55
30 UP – 7A-9D – – 7A-10 7C-B4 – 048.088 7F01-0E – –
56 57 58 59 31 MENU – 7A-84 – – 7A-AB 7C-B2 – 048.084 7F01-0F – –
32 VOL up O 7A-1A VOL UP
33 LEFT – 7A-9F – – 7A-AC 7C-B5 – 048.090 7F01-10 – –
34 ENTER – 7A-DE – – 7A-AD 7C-B8 – 048.092 7F01-11 – –
5 35 RIGHT – 7A-9E – – 7A-12 7C-B6 – 048.091 7F01-12 – –
36 RETURN – 7A-AA – – 7A-AF 7C-B7 – 048.131 7F01-13 – –
37 DOWN – 7A-9C – – 7A-11 7C-B3 – 048.089 7F01-14 – –
38 DISPLAY – 7A-C2 79-0A 7F-9E 7A-B0 7C-A6 – 048.015 7F01-15 – –
39 VOL down O 7A-1B VOL DOWN
40 REC – (device) 7A-4F – – 7C-8B (DVR REC) 048.055 7F01-16 – (DVR REC)
41 STOP – (device) 7A-09 7F-84 – 7C-85 (DVR STOP) 048.049 7F01-1D – (DVR STOP)
42 PAUSE – (device) 7A-09 7F-83 – 7C-83 (DVR PAUSE) 048.048 7F01-1A – (DVR PAUSE)
43 PLAY – (device) 7A-08 7F-82 – 7C-82 (DVR PLAY) 048.044 7F01-1E – (DVR PLAY)
44 REW (SEARCH -) – (device) 7A-0D 7F-88 7A-A4 7C-86 (DVR REW) 048.041 7F01-17 – (DVR REW)
45 FF (SEARCH +) – (device) 7A-0C 7F-89 7A-A5 7C-87 (DVR FF) 048.040 7F01-18 – (DVR FF)
46 SKIP - – (device) 7A-0B 7F-86 7A-A6 7C-B9 (DVR SKIP-) 048.033 7F01-1B – (DVR SKIP-)
6
47 SKIP + – (device) 7A-0A 7F-87 7A-A7 7C-BA (DVR SKIP+) 048.032 7F01-1C – (DVR SKIP+)
48 1 – 7A-59 79-11 7F-91 7A-E5 7C-94 – 048.001 7F01-01 – –
49 2 – 7A-58 79-12 7F-92 7A-E6 7C-95 – 048.002 7F01-02 – –
50 3 – 7A-94 79-13 7F-93 7A-E7 7C-96 – 048.003 7F01-03 – –
51 4 – 7A-8D 79-14 7F-94 7A-E8 7C-97 – 048.004 7F01-04 – –
52 5 – 7A-56 79-15 7F-95 7A-E9 7C-98 – 048.005 7F01-05 – –
53 6 – 7A-DD 79-16 7F-96 7A-EA 7C-99 – 048.006 7F01-06 – –
54 7 – 7A-95 79-17 7F-97 7A-EB 7C-9A – 048.007 7F01-07 – –
55 8 – 7A-C4 79-18 7F-98 7A-EC 7C-9B – 048.008 7F01-08 – –
56 9 – 7A-87 79-19 7F-99 7A-B1 7C-9C – 048.009 7F01-09 – –
57 0 – 7A-C3 79-10 7F-90 7A-B2 7C-93 – 048.000 7F01-0A – –
7 58 +10 – – 79-1A 7F-9A – 7C-9D – – 7F01-0B – –
59 ENTER – 7A-57 79-0B 7F-8A 7A-B3 7C-9E – – 7F01-0C – –

97
 RX-V363/HTR-6130

● RAV34 RX-V363 (B, G, E, F models), THR-6130 (G, E, F models)

• SCHEMATIC DIAGRAM • PANEL • KEY CODE

Key No. Key Name Custom Code Data Code

+3V
1 STANDBY 7E 7F
2 POWER 7E 7E
3 SCENE1 7A 007F
4 SCENE2 7A 037C
INFO DTV/CBL LEVEL RETURN LEFT 5 SCENE3 7A 0679
6 SCENE4 7A 0976
7 CD 7A 15
SCENE1 STRAIGHT VOLUME- DVD POWER
8 MD/CD-R 7A C9
9 TUNER 7A 16
EON V-AUX DOWN ENTER 10 MULTI CH IN 7A 87
11 DVD 7A C1
MD/CD-R SCENE2 AUDIO SEL PROG- PRESET+ MENU 12 DTV/CBL 7A 54
13 DVR 7A 13
D1
14 V-AUX 7A 55
IR Diode TUNER DISPLAY MUTE RIGHT
U1 18 VOLUME- 7A 1B
uPD6P8MC 19 MUTE 7A 1C
PTY SHEEK
1 20 SCENE3 SLEEP PROG+ VOLUME+ UP STANDBY 20 VOLUME+ 7A 1A
KI/O6 KI/O5 -START
2 19
22 A/B/C/D/E 7A 12
KI/O7 KI/O4
23 PRESET- 7A 11
3 18 MULTI CH IN DVR SUR.DECODE PRESET- NIGHT
S0 KI/O3 24 PRESET+ 7A 10
Q1 R2 4 17
SMT SI/LED KI/O2 25 SLEEP 7A 57
47 ohms PTY SHEEK
5
REM KI/O1
16 SCENE4 ENHANCER CD A/B/C/D/E 26 LEVEL 7A 86
-MODE
6 15 27 UP 7A 9D
VDD KI/O0
7 14
28 MENU 7A 84
Xout KI3
29 AUDIO SEL 7A C3
8 13
Xin KI2 30 LEFT 7A 9F
9 12
GND KI1 31 ENTER 7A DE
X1 10
S2 KI0
11 • KEY NO. LAYOUT 32 RIGHT 7A 9E
4MHz 33 NIGHT 7A 95
1 3 34 RETURN 7A AA
R1 C1
1 ohm 47uF 35 DOWN 7A 9C
1 2 36 DISPLAY 7A C2
2
37 SUR.DECODE 7A 8D
3 4 5 6 38 STRAIGHT 7A 56
39 PROG- 7A 59
7 8 9 10 40 PROG+ 7A 58
11 12 13 14 41 ENHANCER 7A 94
42 INFO 7A A4
43 EON 7A A5
18 19 20 44 PTY SHEEK-MODE 7A A6
45 PTY SHEEK-START 7A A7

22 23 24 25

26 27 28 29

30 31 32 33

34 35 36 37

38 39 40 41

42 43 44 45

98
RX-V363/HTR-6130

RX-V363/HTR-6130

99
RX-V363/HTR-6130