01.

DBC 110 II_G_2209

MACHINE SPECIFICATIONS
(SELECTION SHEET)

DBC 110 II
HORIZONTAL BORING MILL

Draft Correction Approval

/ / /

Confirmed by Control Technology Team 2

Issued by Product Development Team 3

Date : 2022.09

DN SOLUTIONS CO., LTD.

Specifications are subject to change without prior notice. 총8매중1매

01. DBC 110 II_G_2209
HORIZONTAL BORING MILL

DBC 110 II
MACHINE SPEC. SELECTION SHEET

1. TRAVEL

ITEM UNIT SPECIFICATION SELECTION

X-axis mm 2500
Y-axis mm 2000
STROKE
Z-axis mm 1500
DEFAULT
W-axis mm 550
SPINDLE NOSE TO TABLE CENTER mm 550 ~ 2050
SPINDLE CENTER TO TABLE TOP mm 0 ~ 2000

2. DIVIDING TABLE

ITEM UNIT SPECIFICATION SELECTION

TABLE SIZE
mm, kg 1400 × 1800 MAX. 10000
(WIDTH X LENGTH)
LOAD CAPACITY
CAPACITY T-SLOT×NUMBERS mm 24H8 × 9 DEFAULT

MAX. WORKPIECE
DIAMETER mm MAX. Ø 2250
SIZE
EDGE LOCATOR (TABLE) ea 4 OPT. SELECTIVE
MAX. ROTATING SPEED r/min 2
LEAST COMMAND INCREMENT deg. 0.001˚
INDEX DEGREE BY PIN deg. 90˚ DEFAULT
AUTOMATIC TABLE CLAMPING UNIT - HYDRAULIC
B-AXIS ROTARY ENCODER - ABSOLUTE TYPE

3. SPINDLE HEAD

ITEM UNIT SPECIFICATION SELECTION

SPINDLE DIAMETER mm Ø 110

DEFAULT
MILLING SPINDLE DIAMETER mm Ø 210
TYPE 1 kW, N·m 26 / 22 2827 STD.
SPINDLE DRIVE MOTOR 30(15min.) /
MAX. TORQUE TYPE 2 kW, N·m 3261 OPT. SELECTIVE
(30 min./cont. rating) 22 [AMP POWER UP]
TYPE 3 kW, N·m 45/37 5026 OPT.
SPINDLE SPEED r/min 4000
NUMBER OF SPEED RANGES - 3 STEPS
DEFAULT
TOOL CLAMPING FORCE N 23520
SPINDLE AIR PURGE - COLLET AIR
- ISO #50 7/24 TAPER
TOOL SHANK DEFAULT
- BIG PLUS
- MAS403-P50T-1(45˚) STD.
(2)
PULL STUD - CAT 50 (Modified BT Type) OPT. SELECTIVE
- DIN 69872 #50 OPT.

Specifications are subject to change without prior notice. -2/8-

01. DBC 110 II_G_2209
4. AXIS SYSTEM

ITEM UNIT SPECIFICATION SELECTION

RAPID TRAVERSE X / Y / Z / W-axis mm/min 12000 / 12000 / 12000 / 6000

MAX. CUTTING FEEDRATE X / Y / Z-axis mm/min 6000
DEFAULT
BALL SCREW (DIAMETER X LEAD) X / Y / Z / W-axis mm Ø 70×P8 / Ø 70×P12 / Ø 70×P8 / Ø 50×P8
FEED MOTOR X / Y / Z / W / B-axis kW AC 9.0 / 9.0 / 9.0 / 4.0 / 7.0
- 1/3/1/1 STD.
X / Y / Z / W-axis (1)
SELECTIVE
AXIS GEAR BOX REDUCTION RATIO - 2/3/2/2 OPT.
B-axis - 842 DEFAULT
X-axis kN 26.1 STD.
SELECTIVE
X-axis (OPTION) kN 43.9 OPT.
THRUST FORCE
Y-axis kN 24.8 DEFAULT
(NO EXTERNAL LOAD & RAPID VELOCITY)
Z-axis kN 21.9 STD.
SELECTIVE
Z-axis (OPTION) kN 39.7 OPT.
X / Y / Z-axis - ABS. PULSE CODER
FEEDBACK SYSTEM W-axis - ABS. PULSE CODER
B-axis - ROTARY ENCODER
X / Y / Z / W-axis mm 0.010 / 0.008 / 0.008 / 0.010 DEFAULT
POSITIONING
B-axis deg. 9"
ACCURACY(11)
X / Y / Z / W-axis mm ±0.003 / ±0.002 / ±0.002 / ±0.003
REPEATABILITY
B-axis deg. 5"
(11) : Accuracy measuring is based on DN Solutions standard.

5. GENERAL SPECIFICATION

ITEM UNIT SPECIFICATION SELECTION

TANK CAPACITY L 65
HYDRAULIC
MOTOR POWER kW 3.7
POWER UNIT
OPERATING PRESSURE MPa 5.5 DEFAULT
PUMP TYPE - PISTON PUMP
MAX. FLOWRATE L/min 38(60Hz)/32(50Hz)
TANK CAPACITY L 45
LUBRICATION
PUMP MOTOR POWER kW 0.057 x 2EA
DEVICE DEFAULT
DISCHARGE PRESSURE MPa 1.7
DISCHARGE VOLUME L/min 0.15 X 2EA
COMPRESSED PRESSURE MPa 0.54
DEFAULT
AIR(3) CONSUMPTION NL/min 520

SPINDLE TANK CAPACITY L 110

DEFAULT
COOLING CAPACITY kcal/h 9028(60Hz)/7583(50Hz)
CHIP CONVEYOR HINGED BELT SET - STD.
(IN MACHINE SELECTIVE
TO TANK) MAGNETIC SCRAPER SET - OPT.

POWER SOURCE(3) - 3Ph.-AC 220~480 V 50/60 Hz

(5-1)
REQUIRED POWER CAPACITY kVA 67 67(5-2) 84.1(5-3)
UTILITY DEFAULT
(4)
PRESSURE MPa 0.54
COMPRESSED AIR
CONSUMPTION NL/min 520
FLOOR SPACE LENGTH × WIDTH mm 7630 x 6990
MACHINE HEIGHT mm 5070 DEFAULT
(6) 36000
MACHINE WEIGHT kg
MACHINE COLOR - DN SOLUTIONS NEW 4 TONE COLOR STD.
SELECTIVE
- USER DEFINED MACHINE COLOR OPT.
CNC SYSTEM MODEL FANUC 31i DEFAULT

Specifications are subject to change without prior notice. -3/8-

01. DBC 110 II_G_2209
6. STANDARD ACCESSORIES

ITEM UNIT SPECIFICATION SELECTION

SLIDEWAY COVERS (X / Z-axis) SET 1

COLUMN GUIDEWAY COVER(Y-axis) SET 1
SPINDLE ORIENTATION SET BZ SENSOR
PORTABLE MPG SET 1
MAIN OP. PANEL(2-LINKAGE TYPE) SET 1
OPERATOR'S CALL LAMP(RED / YELLOW / GREEN) SET 1
Z AXIS COOLANT PAN SET 1
DEFAULT
TABLE CHIP PAN SET 1
CHIP AIR BLOW SET 1
WORK LIGHT (LED LAMP) SET 1
FOOT SWITCH FOR TOOL UNCLAMP SET 1
INSTALLATION TOOL KIT SET 1

LEVELING BLOCKS & ANCHORING BOLTS(7) SET 1

CUSTOMER'S MANUAL SET 1
(1) : IN CASE OF HIGHER SPINDLE MOTOR THAN STANDARD, IT WILL BE CHANGED.
(2) : SPECIAL ANGLE PULL STUD IS POSSIBLE. FOR MORE INFORMATION, CONSULT WITH DN SOLUTIONS R&D
(3) : TRANSFORMER IS REQUIRED ACCORDING TO SUPPLIED POWER SPECIFCATION.
(4) : CUSTOMER PREPARATION
(5) : DEPEND ON SPINDLE MOTOR POWER
(5-1) SPINDLE TYPE1 (5-2) SPINDLE TYPE2 (5-3) SPINDLE TYPE3
(6) : SPECIFIED WEIGHT IS BASED ON THE MACHINE WITH STANDARD SPECIFICATION INCLUDING STANDARD ACCESSORIES AND EQUIPMENT.
(7) : THIS MACHINE CENTAINLY MUST FOUNDATION WORK AND THE STRENGTH OF THE FOUNDATION MUST BE HIGHER THAN THE LEVEL SPECIFIED BY
OUR COMPANY. REFER TO THE FOUNDATION DRAWING PROVIDED BY OUR COMPANY FOR LAYOUT AND FOUNDATION METHOD.

7. ATC

ITEM UNIT SPECIFICATION SELECTION

ea 40 OPT.
TOOL STORAGE CAPACITY ea 60 OPT. SELECTIVE
ea 90 OPT.
TOOL SHANK - MAS403 BT 50 / CT50 / DIN69871 A 50 OPT. SELECTIVE
- MAS403-P50T-1(45˚) OPT.
PULL STUD - CAT 50 (Modified BT Type) OPT. SELECTIVE
- DIN 69872 #50 OPT.
TOOL SELECTION TYPE - FIXED ADDRESS DEFAULT
mm Φ130(CONT.), Φ250(ADJACENT BOTH-SIDE 1POT EMPTY)
MAX. TOOL DIAMETER DEFAULT
mm Φ600(ADJACENT BOTH-SIDE 2POT EMPTY)(8)
MAX. TOOL LENGTH mm 600 DEFAULT
MAX. TOOL WEIGHT kg 30 DEFAULT
MAX. TOOL MOMENT N·m 34.3
ATC DRIVEN (MAGAZINE ROTATION & CARRIAGE MOVEMENT) TYPE SERVO MOTOR
TOOL CHANGING TIME T-T-T sec. 20
DEFAULT
C-T-C sec. 30
ATC SAFETY FENCE SET 1
ATC OP. PANEL - PORTABLE
(8) : MAXIMUM TOOL DIAMETER IS POSSIBLE WITHOUT SPLASH GUARD.
WHEN USING SPLASH GUARD WITH ROOF/AUTO DOOR MAX. TOOL DIAMETER CAN BE UP TO 250 (AT Y=2000 POSITION)

Specifications are subject to change without prior notice. -4/8-

01. DBC 110 II_G_2209

8. APC

ITEM UNIT SPECIFICATION SELECTION

NUMBER OF PALLETS ea 2

APC TYPE - PARALLEL SHUTTLE (Z-DIRECTION)

PALLET SIZE (WIDTH×LENGTH) mm 1400 × 1800

OPT. SELECTIVE
MAX. WORKPIECE WEIGHT kg 6000

T-SLOT x NUMBERS mm 24H8 x 9

RAISING BLOCK mm 280

9. FEEDBACK SYSTEM

ITEM UNIT SPECIFICATION SELECTION

X-axis SET ABSOLUTE TYPE

LINEAR SCALE FEEDBACK SYSTEM Y-axis SET ABSOLUTE TYPE OPT. SELECTIVE

Z-axis SET ABSOLUTE TYPE

10. COOLANT SYSTEMS(9)

ITEM UNIT SPECIFICATION SELECTION

TANK CAPACITY L 650

FLOOD COOLANT
PUMP MOTOR POWER kW 1.1
FILTERATION mesh 10(TANK SCREEN FILTER)
OPT. SELECTIVE
MAX. PRESSURE MPa 0.70(60Hz)/0.47(50Hz) 1.0(60Hz)/0.7(50Hz)
MAX. FLOWRATE L/min 30 20
PUMP TYPE IMMERSION TYPE
PUMP MOTOR POWER kW 1.5
COOLANT SYSTEM FILTERATION ㎛ 10(CYCLONE FILTER TYPE)
- MIDDLE
PRESSURE TSC I MAX. PRESSURE UNDER BLOCKING MPa 2.1(60Hz)/2.0(50Hz) OPT. SELECTIVE
MAX. FLOWRATE WITHOUT TOOL L/min 10(10)
PUMP TYPE T-ROTOR TYPE
PUMP MOTOR POWER kW 4.0
COOLANT SYSTEM FILTERATION ㎛ 10(CYCLONE FILTER TYPE)
- MIDDLE
PRESSURE TSC II MAX. PRESSURE UNDER BLOCKING MPa 2.0(60Hz)/1.3(50Hz) OPT. SELECTIVE
(10)
MAX. FLOWRATE WITHOUT TOOL L/min 20
PUMP TYPE IMMERSION TYPE
PUMP MOTOR POWER kW 5.5 7.5
COOLANT SYSTEM FILTERATION ㎛ 25(BAG FILTER TYPE) 10(CYCLONE FILTER TYPE)
- HIGH
PRESSURE TSC I MAX. PRESSURE UNDER BLOCKING MPa 7.0 OPT. SELECTIVE

MAX. FLOWRATE WITHOUT TOOL L/min 29(60Hz)/20(50Hz)(10)

PUMP TYPE DIAPHRAGM TYPE

COOLANT GUN SET - OPT. SELECTIVE

OIL SKIMMER TYPE SET BELT OPT. SELECTIVE

COOLANT LEVEL
SET LOW / HIGH OPT. SELECTIVE
SWITCH

Specifications are subject to change without prior notice. -5/8-

01. DBC 110 II_G_2209

11. CHIP CONVEYOR & BUCKET

ITEM UNIT SPECIFICATION SELECTION

LIFT UP CHIP CONVEYOR HINGED BELT SET - OPT.

SELECTIVE
(FROM COOLANT TANK TO CHIP BUCKET) MAGNETIC SCRAPER SET - OPT.
TYPE DN SOLUTIONS STANDARD TYPE OPT.
CHIP BUCKET SELECTIVE
CAPACITY L 380 OPT.

12. SAFETY GUARD

ITEM UNIT SPECIFICATION SELECTION

SEMI TYPE - TABLE ON COVER W/O ROOF COVER OPT.

COOLANT SPLASH GUARD
(8)
SEMI TYPE - TABLE ON COVER W/H AUTO DOOR OPT. SELECTIVE
SAFETY FENCES & INTERLOCK SWITCHES - ENCLOSURE OF MACHINE WITH FENCES OPT.

13. ADDITIONAL 6th AXIS

ITEM UNIT SPECIFICATION SELECTION

PACKAGE #1 - PACKAGE #1 + PIPING + AMP OPT.

(*)
ADDITIONAL 6th AXIS SELECTIVE
PACKAGE #2 - FULL PACKAGE OPT.

14. PNEUMATIC ACCESSORY

ITEM UNIT SPECIFICATION SELECTION

AIR AIR GUN SET 1 OPT.

MQL SET 1 OPT.
SELECTIVE
AIR DRYER SET 1 OPT.
AIR COMPRESSOR SET 1 OPT.

15. ATTACHMENT & FIXTURE

ITEM UNIT SPECIFICATION SELECTION

SPINDLE SPEED r/min 1500

90˚ ANGLE HEAD POWER kW 15
- L420
ANGULAR MILLING CENTER
mm 420
TO SPINDLE FLANGE OPT. SELECTIVE
IN / OUT SPEED RATIO - 1:1
TOOL SHANK - ISO #50 7/24 TAPER
CLAMPING METHOD - MANUAL
SPINDLE SPEED r/min 1500
90˚ ANGLE HEAD POWER kW 15
- L650
ANGULAR MILLING CENTER
mm 650
TO SPINDLE FLANGE OPT. SELECTIVE
IN / OUT SPEED RATIO - 1:1
TOOL SHANK - ISO #50 7/24 TAPER
CLAMPING METHOD - MANUAL

Specifications are subject to change without prior notice. -6/8-

01. DBC 110 II_G_2209
15. ATTACHMENT & FIXTURE (CONTINUED)

ITEM UNIT SPECIFICATION SELECTION

SPINDLE SPEED r/min 1000

UNIVERSAL HEAD
POWER kW 15
ANGULAR MILLING CENTER
mm 545
TO SPINDLE FLANGE OPT. SELECTIVE
IN / OUT SPEED RATIO - 1:1
TOOL SHANK - ISO #50 7/24 TAPER
CLAMPING METHOD - MANUAL
ALLOWABLE SPEED r/min 150
FACE PLATE
OUTER DIAMETER mm Ø 650
MAX. STROKE mm 170 OPT. SELECTIVE
T-SLOT mm 16H7 x 2, PITCH 180
WEIGHT kg 245
ALLOWABLE SPEED r/min 1000
SPINDLE
OUTSIDE DIAMETER mm 170
SUPPORT OPT. SELECTIVE
OVERALL LENGTH mm 200
WEIGHT kg 50
COGSDILL OPT. SELECTIVE
FACING HEAD
ATTACHMENT READY MAKER ITS OPT. SELECTIVE
(NC TYPE) (*)
D'ANDREA OPT. SELECTIVE
FIXTURE ANGLE PLATE L×H×W mm 450 × 600 × 400 OPT.
mm 500 × 1000 × 550 OPT.
SELECTIVE
mm 750 × 1250 × 750 OPT.
mm 1000 × 2000 × 1000 OPT.

16. MEASUREMENT

ITEM UNIT SPECIFICATION SELECTION

TOOL SETTING GUIDE AUTO. TOOL LENGTH MEASUREMENT SET RENISHAW / TS27R OPT. SELECTIVE
WORK SETTING SET RENISHAW / OMP60 OPT. SELECTIVE
AUTO. WORKPIECE MEASUREMENT
GUIDE SET RENISHAW / RMP60 OPT. SELECTIVE
TEST BAR TOOL SHANK - ISO #50 7/24 TAPER
OPT. SELECTIVE
LENGTH mm 300

Specifications are subject to change without prior notice. -7/8-

01. DBC 110 II_G_2209
17. OTHERS

ITEM UNIT SPECIFICATION SELECTION

SPINDLE THERMAL COMPENSATION SYSTEM(Z-axis) SET 1 OPT. SELECTIVE

MAINTENANCE TOOL KIT SET L-WRENCH AND SPANNER SET OPT. SELECTIVE
(9) : REAL PRESSURE AND FLOW RATE CAN BE CHANGED BY MACHINE & TOOL CONDITION.
FOR MORE INFORMATION, CONSULT WITH DN SOLUTIONS R&D
(10) : THIS VALUE CAN BE CHANGED BY PUMP OUTLET PRESSURE AND TOOL HOLE DIAMETER.
FOR MORE INFORMATION, CONSULT WITH DN SOLUTIONS R&D

<Note>
1. SPECIFICATION MARKED BY '(*)' SHOULD BE REVIEWED IN DETAIL BEFORE CONTRACT.
2. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
3. THE OPTIONS DESCRIBED ABOVE, IT CAN BE CHANGED AFTER DEVELOPMENT COMPLETION.

Specifications are subject to change without prior notice. -8/8-