Vibrro Con
ntrol 300
3 V
Vibration Controlle
er Module
e
The Vibro Controller
C 300
0 is a 4 chann
nels Vibration Monitor des
signed to me
easure and
protect crittical machine
ery.
Now, persoonnel who are e not “vibratiion experts” can easily reecognize alarm m
conditions using the Vib
ibro control3000 standard process
p conttrol signal to
interface with
w standard PLC, DCS an nd SCADA sy ystems. Addiitionally, vibrration
analysts ca
an access thee dynamic sig gnal for detaiiled analysis with industry y
standard data collectorss and online monitoring systems.
s
CONDITIONERS
Features
• Microprocessorr based system provides the industtry’s most accuratte filtering. Digitall filters from 5 Hz to
15 kHz provide
e precise overall a
amplitudes. Four pole filters at 2 Hz and 20 Hz add flexibility to monittoring options
• DIP switches allow
a easy “field co nput signal, scale values and filterin
onfiguration” for in ng options
• Accepts a varieety of signal inputss; Acceleration, Velocity
V and Displaacement (see belo ow)
• Provides scaled d outputs in English and metric - up p to double integrration (see below)
Module
• Configure for in
ntegration converssions(see below)
• 4 sensors inputt channels
• 8 assignable reelay out put for shuutdown & trip
• Including of 4 selector
s buttons foor LCD and keybo oard
ons
Specificatio
SIGNAL
Conditioner
•
Signal Controller
4-20 mA outp ation Overall or D ynamic signal
put signal for vibra
• Additional Mo
odBus (RTU) Proto ocol
• Buffered outp
put via BNC and screw
s terminals
• Humidity rangge of 0-95% relativve, non-condensin ng
• Screw terminaal connectors, dettachable
& TEMPERATURE
• Ambient temp perature range: -440° F (-40° C) to 185° F (85° C)
• Additional AP
PI670 features :Bypass, programma able Alarm ,delay etc.
e
Electrical A
Application
Vibration
• Input power: 12
1 t0 60 VDC unrregulated / 80 mA maximum. • Turbochargerss
• Power from conditioner to sen nsor: 24 VDC, 4 mA
m DC sensor exc
citation. • Generators
• Isolation: 500
0 VDC. • Industrial Fanss & Blowers
• Compressors
Vibro contrrol 300 Sele
ection
Vibration
Example
e: control3
300-3 - 1 0 0 A - 0 10 M R - 003 - 0 1 K – O–
–1 (standarrd ISO Config
guration)
¾ This adju
ustment according
g to table at the below
b should be set for channel 1 up
u to 4
VIBRATION
C
Control300 - - - - - -
Full Sca
ale Higgh Pass Voltage
Configuration Input S
Source Full Scalle Units Lo
ow Pass
Range Fillter Output
Fillter
Value
2
3= ISO (Stan
ndard) 100A = 100 mV/g Accelerometerr 0X5 = 0 - 0.5 A=m/s P= 00
02 = 2 Hz 00
05 = 50 Hz
(see example above) 050A = 5
50 mV/g Accelerometeer Peak
003 = 3 HZ 00
07 = 70 Hz O=4~20 mA
010A =
001 = 0 - 1
10 mV/g Accelerometeer
V =mm/ss 010 = 100 Hz (Overall data)
7 = Factory
Number of channel
500A = 5
500 mV/g Acceleromete
er 002 = 0 - 2 00
05 = 5 Hz 20 = 200 Hz
02
configured R=
per part
RMS 010 = 10 Hz 05
50 = 500 Hz
100V = 1100 mV/IPS Velocity Sennsor 005 = 0 - 5 G= g D=4~20 mA
number 500V = 500 mV/IPS Velocity Sensor 02
20 = 20 Hz 10
00 = 1000 Hz
010 = 0 - 10 D = mils T= 15
50 = 1500 Hz (Dynamic Data
a)
*AllVibrocontrol3 300 200D = 200
05
50 = 50 Hz
2 mV/mils Displacem
ment
020 = 0 - 20 Peak- 20
00 = 2000 Hz
systems are usser 008D = 8 V/mm Displacement U=µm Peak 10
00 = 100 Hz 50
00 = 5000 Hz
configurable aftter 050 = 0 - 50 20
00 = 200 Hz 10
0K = 10000 Hz
initial set up XXXA= Variable
V Accelerometer sensor
s
100 = 0 - 100 I=IPS
XXXV =Variable
V Velocity sensor 50
00 = 500 Hz
200 = 0 - 200 M =mm 01K = 1000
Hz
Example: control3
300-7 - 1 0 0 A - 0 0 1 M R - 0 0 5 - 0 5 0 – O–2
LIFETIME
E WARRA
ANTY ON
N MATERIIALS & W
WORKMANSHIP
WWW.A
ABPVibro.com
