TADANO

TR-350XL
35 Ton Capacity (31.7 Metric Tons)
HYDRAULIC ROUGH TERRAIN CRANE
DIMENSIONS

Min 29'10¼" (9.1m) Max 93'10" (28.6m)

7'%" (2.15m)

oz· ] j

5'71%¢" (1.73m) 5'74" (1.73m)

10'%%" (3.05m) 10'117%" (3.35m)

11'11%" (3.65m) 11 '8¼" (3.56m) 12'5%%¢" (3.79m)

36'1%%" (11.0m)

GENERAL DIMENSIONS
(20.5 X 25 Tires)
Feet Meters
Tail swing counterweight 10'10" 3.3
Turning Radius:
4 wheel steer 20' 10" 6.35
2 wheel steer 35' 3 1/4" 10.8

7'4 (2.14m)
A
8'117%" (2.74m)

20'8%¢" (6.3m)

21'114" (6.7m)
CRANE SPECIFICATIONS
BOOM

Four section full power partially synchronized telescoping boom, Vire Rope - Filler wire, extra improved plow steel, pre-formed,
29.9'-93.8' (9.1-28.6m), of box construction with five sheaves, 12 independent wire rope core, right regular lay.
5/8" (0.32m) root diameter, at boom head. The synchronization 5/8" (16mm) 6 x 37 class
system consist of two telescope cylinders, an extension cable and
retraction cable. Hydraulic cylinders fitted with holding valves.
Two easily removable wire rope guards, rope dead end provided HOOK BLOCKS
on right side of boom head. Boom telescope sections are sup- 1. 35 ton (31.7 metric ton) - 5 sheaves with swivel hook and safety
ported by wear pads both vertically and horizontally. latch, for 5/8" (16mm) wire rope.
2. 22 ton (20 metric ton)-3 sheaves with swivel hook and safety
BOOM ELEVATION - By a double acting hydraulic cylinder with latch, for 5/8" (16mm) wire rope.
holding valve. Elevation 0°-80°, combination controls for hand or 3. 4.4 ton (4.0 metric ton) - Weighted hook with swivel and safety
foot operation. Boom angle indicator. latch, for 5/8" (16mm) wire rope.

JIB - Box type top section telescopes from lattice type base sectior
which stores alongside base boom section. 5, 25° or 45° offset HYDRAULIC SYSTEM
(tilt type). Single sheave, 13 7/8" (0.352m) root diameter, at jib
head. Jib length is 23.6' (7.2m) 0r 42' (12.8m). PUMPS - Two variable piston pumps for telescope, elevation, and
hoist. Tandem gear pump for swing, outriggers, steering and
AUXILIARY LIFTING SHE WE (SINGLE TOP) - Single sheave, optional equipment. Powered by carrier engine. Pump disconnect
12 5/8" (0.32 m) root diameter. Mounted to main boom head for for crane is engaged/disengaged by rotary switch from operator's
single line work. (Stowable.) cab.

ANT-Tw, 8.0C,- Pendant type over-winding cut out device

CONTROL VALVES - Multiple valves actuated by hand levers with
with audio-visual (FAILURE lamp/BUZZER) warning system.
integral pressure relief valves.

SWING
Hydraulic axial piston motor driven through planetary swing speed - 120 gallon (456 lit.) capacity. External sight level
reducer. Continuous 360° full circle swing on ball bearing turntable gauge.
at 3.4 rpm. Equipped with manually locked/released swing brake.
A swing lock (pin-in-hole lock) for pick and carry and travel modes,
manually engaged in cab FI!TRATION - 26 micron return filter, full flow with bypass protec-
tion, located inside of hydraulic reservoir. Accessible for easy re-
HOIST placement.

MAIN HOIST - Variable speed type with grooved drum driven by CAB AND CONTROLS
hydraulic axial piston motor through winch speed reducer. Power
load lowering and raising. Equipped with automatic brake (Neutral Both crane and drive operations can be performed from one cab
brake) and counterbalance valve. Controlled independently of mounted on rotating superstructure.
auxiliary hoist.
Left side, 1 man type, steel construction with sliding door access
DRUAM - Grooved 12 5/8" (0.320 m) root diameter x 19 1/16" and safety glass windows opening at side, rear and roof. Wind-
(0.4845 m) wide. Wire rope: 574 ft. of 5/8" diameter rope (175m of shield glass window is shatter-resistant. Tilt-telescoping steering
16mm). Drum Capacity: 734 ft. (223.6m) 6 layers. Maximum line wheel. Adjustable control levers for swing, boom telescoping, boom
pull (permissible): 10, 078 lbs. (4571 kg). Maximum line speed: hoist, auxiliary hoist and main hoist (with swing free-lock selector
394 FPM (120 m/min). switch). Control levers for swing and boom hoist can change neutral
positions and tilt for easy access to cab. Engine throttle knob. Foot
AUXILIARY HOIST - Variable speed type with grooved drum operated controls: boom hoist, service brake and engine throttle.
driven by hydraulic axial piston motor through winch speed reducer.
Power load lowering and raising. Equipped with automatic brake Dash-mounted engine start/stop, monitor lamps, cigarette lighter,
(neutral brake) and counterbalance valve. Controlled independently parking brake switch, steering mode select switch, rear steering lock
from main hoist. switch.

DRUM - Grooved 12 5/8" (0.320 m) root diameter x 10 3/8" (0.2635 Instruments - Torque converter oil temperature, engine water
m) wide. Wire rope: 295 ft. of 5/8" diameter rope (90m of 16mm). temperature, air pressure, fuel, hydraulic oil pressure, speedometer,
Drum capacity: 399 ft. (121.6m) 6 layers. tachometer and hour meter
Maximum line pull (permissible): 10, 078 lbs. (4 571 kg).
Maximum line speed: 394 FPM (120m/min).

Maximum permissible line pull may be affected by wire rope strength.

2
Tadano electronic LOAD MOMENT INDICATOR system (AML-M) Operator's cab console includes transmission gear selector, pump
including: engaged/disengaged switch, suspension spring lock switch,
- Control lever lockout function outrigger controls, sight level bubble, drive selector switch, swing
- Working radius and/or boom angle preset function free-lock selector switch, working light switch and ashtray. Swing
(warning only ) lock knob, swing brake and 4 way adjustable seat with high back
- Warning buzzer (with seat belt).
- Boom angle/boom length/jib offset angle/working
radius rated loads/actual loads read out
- Ratio of actual load moment to rated load moment
indication
- Working condition register switch
- External warning lamp

CARRIER SPECIFICATIONS
TYPE . Rear engine, left hand steering, driving axle 2-way selected SUSPENSION . Front: Semi-elliptic leaf springs with hydraulic
type by manual switch, 4 x 2 front drive, 4 x 4 front and rear drive. lockout device. Rear: Semi-elliptic leaf springs with hydraulic
lockout device
FRAME - High tensile steel, all welded box construction.
BRAKE SYSTEMS - Service: Air over hydraulic disc brakes on all
AUTOMATIC TRANSMISSION - Electronically controlled full auto- 4 wheels. Parking/Emergency: Spring applied-air released brake
matic transmission. Torque converter driving full powershift with acting on input shaft of front axle.
driving axle selector. 6 forward and 2 reverse speeds, constant
mesh. TIRES Standard 20.5 x 25 - 24 PR (OR),

3 speeds - high range - 2 wheel drive; 4 wheel drive

3 speeds - low range - 4 wheel drive OUTRIGGERS - Four hydraulic, beam and jack outriggers.
Vertical jack cylinders equipped with integral holding valve. Each
TRAVEL SPEED -31.2 mph maximum. outrigger beam and jack is controlled independently from cab.
Beams extend to 20' 8 1/16" (6.3m) centerline-to-centerline and
AXLE - Front: Full floating type, steering and driving axle with retract to within 8' 6 3/8" (2.6m) overall width with floats. Outrigger
planetary reduction. Rear: Full floating type, steering and driving jack floats are attached thus eliminating the need of manually
axle with planetary reduction. Non-spin differential. attaching and detaching them. Controls and sight bubble located
in upper structure cab.
STEEING - Hydraulic power steering controlled by steering
wheel. Three steering modes available: 2 wheel front, 4 wheel
coordinated and 4 wheel crab.

ENGINE
Model Mitsubishi 6D16T
Type Radiator Fin and tube core, termostat controlled
Direct Injection Diesel
No. of cylinders Fan, in. (mm) Suction type, 6-blade, 23.6 (600) dia.
6
Combustion Starting 24 volt
4 cycle, turbo charged
Bore x Stroke, in. (mm) Charging 24 volt system, negative ground
4.646 X 4.528 (118 x 115)
Displacement, cu. in (liters) Battery 2-140 amp. hour
460 (7.545)
Air inlet heater Compressor, air, CFM (I/min) 21.3 CFM (602 ) at 2,000 rpm
24 volt preheat
Air cleaner Horsepower,(kW) Net 215 (158) at 2800 rpm
Dry type, replacement element (dual)
Oil filter Torque, Max. ft-lb (kgm) 470 (65) at 1600 rpm
Full flow with replacement element
Fuel Filter Capacity, gal. (liters)
Full flow with replacement element
Fuel tank, gal. (liters) Cooling water 3.4 (13)
79.3 (300), right side of carrier
Cooling Lubrication 3.7-4.2(14-16)
Liquid pressurized, recirulating by-pass

3
STANDARD EQUIPMENT
- Four section full power partially synchronized boom 29.9'- 93.8' - Rear view mirrors (right and left side)
(9.1 m-28.6m) - 4 way adjustable seat with high back
- Two stage stowable telescoping jib 23.6' (7.2m) or 42' (12.8m) - Tilt-telescoping steering wheel
with 5°, 25°, 45° pinned offset (tilt type) - Neutral position adjustable control lever (swing and boom hoist)
- Auxiliary lifting sheave (single top) stowable - Seat belt
- Boom hoist foot control - Cab floor mat
- Boom angle indicator - Electric fan in cab
- Variable speed main hoist driven by axial piston motor - Back up alarm
- Variable speed auxiliary hoist with cable follower - Low oil pressure/high water temperature warning device (visual)
- Tadano twin swing system - Fenders
- 4 x 4 x 4 drive - Towing hooks - front and rear
- Hydraulic lockout suspension system - Lifting eyes
- Independently controlled outriggers - Tool storage compartment- External warning lamp
- Self-storing outrigger pads - Full instrumentation package
- Electronic controlled automatic transmission driven by torque - Pump disconnect in operator's cab
converter - Non-spin rear differential
- Complete highway light package - Water separator with filter
- Anti two block device (Overwind cutout) - Flood lights
- Electronic crane monitoring system - Outrigger hose protection
- Tadano electronic load moment indicator system (AML-ML) - 24 volt electric system
including: - 24 volt start
-Control lever lockout function - Tire inflation kit (with tire pressure gauge)
- Working radius and/or boom angle preset function
- 35 ton (31.7 metric ton) 5 sheave hook block
(warning only)
- 4.4ton (4 metric ton) hook ball and swivel
- Warning buzzer
Boom angle/boom length/jib offset angle/working radius/
rated loads/actual loads read out OPTIONAL EQUIPMENT
- Ratio of actual load moment to rated load moment - 22 ton (20 metric ton) 2 sheave hook block
indication - Propane heater
- Working condition register switch - Fire extinguisher
- External warning lamp - Tool kit
- Front windshield wiper and washer - Drum rotation indicator (thumper type) main and/or aux hoist
- Roof windshield wiper
- Roof windshield lock warning

HOISTING SPECIFICATIONS
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
.. ------------- -- --

Main or auxiliary hoist - 12 5/8° (0.32 m) drum Main Drum Grooved Lagging Aux. Drum Grooved Lagging
Line Line pulls Wire 5/8" (16 mm) wire rope 5/8" (16 mm) wire rope
- ----

Speeds2 Rope Rope per layer Total wire rope Rope per layer Total wire rope
Available1 Permissible 4
Layer Speed Layer ----- ----7
F.P.M m/min Lbs. kgf Lbs. kgf Feet Meters Feet Meters Feet Meters Feet Meters
1 99 30.1 99 30.1 54 16.4 54 16.4
Low 133 41
1st 11,086 5028 10, 078 4571 2 108 32.9 207 63.0 59 17.9 113 34.3
High 266 81
3 117 35.8 324 98.8 64 19.5 117 53.8
Low 146 45
2nd 10,642 4827 9675 4388 4 127 38.7 451 137.5 69 21.0 245 74.8
High 292 89
5 136 41.6 588 179.1 74 22.6 320 97.4
Low 159 49
3rd 10,270 4658 9336 4235 6 146 44.5 734 223.6 79 24.2 399 121.6
High 318 97
Low 171 52
4th 9953 4515 9048 4104
High 341 104 DRUM DIMENSIONS
Low 184 56
5th 9680 4391 8800 3992
High 367 112 MAIN AUXILIARY I

6th3
Low 197 60
9442 4283 8584 3893 Inch mm Inch mm i
High 394 120 Root Diameter 12 5/8 320 12 5/8 320 I
Length 19 1/16 484.5 10 3/8 263.5
'Developed by machinery with first layer of wire rope, but not based on rope strength or Flange Diameter
other limitation in machinery or equipment.
20 7/8 530 20 7/8 530 I
'Line speeds based only on hook block, not loaded.
'Sixth layer of wire rope is not recommended for hoisting operations.
Permissible line pull may be affected by wire rope strength.

4
 TR-350XL
OPERATfNG RADIUS / LIFTING HEIGHT CHART
150'

140'

130'

120'

110'

100'
t
QJ
0 90'
LL
c
d
80'
c
0o
QJ
70
1
a.o
c 60'
t"
•
�
50'

40'

30'

20'

10'

130' 120' 110' 100' 90' 80' 70' 60' 50' 40' 30' 20'
t..ltd.ltd.
Axis of Rotation
Operating Radius from Axis of Rotation in Feet
NOTE: Boom and jib geometry shown are for unloaded condition and machine standing level
on firm supporting surface. Boom deflection and subsequent radius and boom angle
change must be accounted for when applying load to hook.

5
 TR-35OXL TOTAL RATED LOAD CHART (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 360° ROTATION
Load
Boom Length in Feet
Radius
Boom Length In Feet Boom Length in Feet
in 29.9 37 44 51.2 58
Boom
65 72.5 80 87 93.8
0L
Angle 33.8(286n)8con+235(72) $38(286n)8on+42(128r)>
Feet (9.1m) (11.3m) (13.4m) (15.6m) (17.7m) (19.8m) (22.1m) (24.4m) (26.5m) (28.6m) r 29.9( 9.1m)
Degree
10 70.000
(58°)
49.900 49,900 43.200 37.600
(65°) (69°) (73°) (75°)
36.600 28.700
(78°) 5°tilt 25°tilt 45°tilt 5°tilt 25°tilt 45°tilt SR-r
(77° 37(11.3m)
12 53.700 49.900 49.900 43.200 37.600 35.000 28.700 26,500 8O°6.600 4,400 3.300 4,400 2.200 1.500
(53°) (61°) (66°) (70°) (73° (75° (77°) (78°) Se I
75°6.600 4.400 3.,300 4.400 2.200 1.500
15 46.100 44,000 42,700 39.600 33.400 30.200 28,700 26.500 22.400 18,350 44'( 13.4m)
(45°) (56° (62°) (67°) (70°) (73°) (75° (77°) (78° (79°) 7O°6.500 4,400 3.300 3.700 2.200 1.500
35.400 34,600 34,200 31,300 27.000 25.100 24.000 21,500 19,700 18,350 65°5,200 3.900 3.300 3.150 2.000 1,500 $¢. III
20 (28°) (46°) (54°) (60°) (65°) (68°) (70°) (73°) (74°) (76°) 6O°4.300 3.400 3.050 2.700 1.900 1.450 51.2(15.6n)
25 26.600 26.600 25.100 22.000 21,000 20.000 17.800 16.200 15,700 55°3.650 3.000 2,750 2.300 1.750 1.400
(32°) (45°) (53°) (58°) (63°) (66°) (69°) (71°) (73°) $$n II I I
20.000 18.700 18.000 17,000 16.600 14,900 13,700 13,500 5O°3.100 2.700 2.500 2.000 1.600 1.350
30 (34°) (46°) (53°) (57°) (61°) (65°) (67°) (69°) 58'(17.7m)
Las .2.700 2.400 2.350 1.750 1.450 1.300
35 14.700 14.800 15,000 14,300 13.800 12.600 11,750 11.600 4O° 2,000 i 1.,850 1.550 1.350 $ $ II;
(19°) (37°) (46°) (52°) (57°) (61°) (64°) (66°)
35° 1.550 1,400 1.200 1.100 65(19.8m)
11.600 11 900 11,600 11.500 10,700 10.150 10,100
4O (25°) (38°) (46°) (52°) (57°) (60°) (63°) 3O° 1.200 1.100 950 900
9.400 9.400 9.350 9.000 8.900 8.900 25° 950 950
45 (28° (39°) (46°) (52°) (56°) (59°) 72.5(22.1m)
7.600 7.900 8.100 8.100 8.100 8.100 3,300lbs.(1.500kgs) shall be subtracted from
50 (11°) (31°) (40°) (47°) (51°) (55° the total rated load of the main boom when W
80(24.4m)
6.500 6.700 6.800 6.800 6.800 jib is attached to main boom head.
55 (19°) (33°) (41°) (47°) (51°)
W
60 5.650 5.650 5.650 5.650 87'(26.5m)
(25° (35°) (42°) (47°)
65 4.800 4.800 4.800 4.800
(10° (28°) (37°) (42°) l

93.8(28.6m)
4.250 4.250 4.250
70 (17°) (30° (37°) NOTE Standard number of part lines for outrigger ope ration should be according
3 600 3 600 to the following table
75 (21° (31°) --- --
3150 Boom Length 29.9 37 to 51.2 58 to 72.5 80' to 93.8 Srgle top
80 (24°) n Feet
2.650 (meters) (91) (11.3 to 15.6) (17.7 1o 22.1) (24.4 to 28.6) Jb
85 (14°)
No of
part line
10 8 6 4
Boom Angles are in degrees.
In the LOAD MOMENT INDICATOR (AML-M), the lifting capacity data based on
the standard number of part line listed in the chart s stored.

WARNING AND OPERATING INSTRUCTIONS FOR LIFTING CAPACITIES

GENERAL
1. Total rated loads shown on the TOTAL RATED LOAD CHART apply only to the machine 1O. Load per line should not exceed 8,8O0 lbs (4000 kg).
as originally manufactured and normally equipped by TADANO LTD. Modi- 11. Loaded boom angles are approximate. The boom angle before loading should be
fications to the machine or use of optional equipment other than that specified greater to account for deflection.
can result in a reduction of capacity. 12. The 29.9'(9.1 m) boom length capacities are based on boom fully retracted. If not fully
2. Construction equipment can be dangerous if improperly operated or maintained. retracted [less than 37' (11.3 m)boom length], use the total rated loads for the
Operation and maintenance of this machine must be in compliance with the 37' (11.3 m) boom length.
information in the operation, safety and maintenance manual supplied with 13. Extension or retraction of the boom with loads may be attempted within the limits of the
machine. If this manual is missing, order replacement through the distributor. TOTAL RATED LOAD CHART. The ability to telescope loads is limited by
3 The operator and other personnel associated with this machine shall fully acquaint hydraulic pressure, boom angle, boom length, crane maintenance, etc.
themselves with the latest applicable American National Standards Institute
(ANSI) safety standards for cranes. 14. For lifting capacity of single top. reduce the total rated loads of relevant boom by 550
lbs (25O kg). Capacities of single top shall not exceed 6,610 lbs (3000 kgs)
SET UP including main hook.
1. Total rated loads shown on the chart are the maximum allowable crane capacities and 15. When erecting and stowing jib, be sure to retain it by hand or by other means to prevent
are based on the machine standing level on firm supporting surface under its free movement.
ideal job conditions. Depending on the nature of the supporting surface, it may 16. 33OO lbs (15OO kgs) shall be subtracted form the total rated loads of the main
be necessary to have structural supports under the outrigger floats or tires to boom. when jib is attached to main boom head. Jib weight is 1300 lbs
spread the load to a larger bearing surface. (590 kg).
2. For outrigger operation, outriggers shall be fully extended with tires free of supporting 17. Use Anti-Two Block (OVERWIND CUTOUT) disable switch when erecting and
surface before operating crane. stowing the jib and stowing the hook block. While the switch is pushed, the
hoist does not stop, even when overwind condition occurs.
OPERATION 18. For boom lengths with 23.6(7.2 m) Jib, total rated loads are determined by loaded
1. Total rated loads with outriggers fully extended do not exceed 85% of the tipping loads boom angle only in the column headed "93.8' (28.6 m) Boom+ 23.6' (7.2 m)
as determined by SAE Crane Stability Test Code J-765. Jib". For boom length with 42' (12.8m) jib, total rated loads are determined
2. Total rated loads above bold lines in the chart are based on crane strength and those by loaded boom angle only in the column headed "93.8' (28.6m) boom + 42
below, on its stability. They are based on actual load radius increased by (12.8m) jib". For angles not shown, use the next lower loaded boom angle
boom deflection. to determine allowable capacity.
3. Total rated loads include the weight of main hook block (770 lbs for 35 tons capacity), 19. When lifting a load by using jib (auxiliary hoist) and boom (main hoist) simultane-
auxiliary hook ball (220 lbs for 4.4 tons capacity), sling and auxiliary lifting ously, do the following:
devices and their weights shall be subtracted from the listed capacities to • Illuminate the jib indicator lamps and make the jib offset display screen
obtain the net load to be lifted. indicate the same value as the actual offset by repeatedly pushing the
4. Total rated loads are based on freely suspended loads and make no allowance for such boom state register switch.
factors as the effect of wind, sudden stopping of loads, supporting surface • Before starting operation, make sure that the weight of load is within the
conditions, inflation of tires, operating speeds, side loads, etc. Side pull on total rated load for jib.
boom or jib is extremely dangerous.
5. Total rated loads do not account for wind on lifted load or boom. Total rated loads and
boom length shall be appropriately reduced, when wind velocity is above 20 DEFINITIONS
mph (9m/sec.). 1. Load Radius: Horizontal distance from a projection of the axis of rotation to
6. Total rated loads at load radius shall not be exceeded. Do not tip the crane to determine supporting surface before loading to the center of the vertical hoist line or
allowable loads. tackle with load applied.
7. Do not operate at boom lengths beyond radii or boom angle, where no capacities are 2. Loaded Boom Angle: The angle between the boom base section and the horizontal.
shown. Crane may overturn without any load on the hook. after lifting the total rated load at the load radius.
8. When boom length is between values listed, refer to the total rated loads of the next 3. Working Area: Area measured in a circular arc about the centerline of rotation.
longer and next shorter booms for the same radius. The lesser of the two total 4. Freely Suspended Load: Load hanging free with no direct external force applied
rated loads shall be used. except by the hoist line.
9. When making lifts at a load radius not shown, use the next longer radius to determine 5. Side Load: Horizontal side force applied to the lifted load either on the ground or in
allowable capacity. the air.

6
 Working Area
TR-35OXL TOTAL RATED LOAD CHART (IN POUNDS)
TIRE :20.5-25 24PR
360°
ON RUBBER

Load
Radius
p
Over Front
Boom Length in Feet
Stationary
360° Rotation
Boom Length in Feet
Creep
Over Front
Boom Length in Feet
Over
Front
+]
\ ear
Approx.
Feet
29.9 51.2 65' 80' 29.9 51.2 65 80' 29.9' 51.2 65 80' 2°
(9.1m) (15.6m) (19.8m) (24.4m) (9.1m) (15.6m) (19.8m) (24.4m) (9.1m) (15.6m) (19.8m) (24.4m)
10 36.900 29.000 25,600 25,250 30,600 26,100
12 32,800 29.000 22.000 18,700 18.320 19,600 26,350 26,100 22.000
15 27.600 25,000 22,000 13.500 12.570 12,200 13.200 13.500 21.500 21.250 19.700 13,500
20 17.750 17,450 17.500 13.000 7,200 6,850 7,800 8,300 15,850 15,650 15,600 13,000 Boom Length in Feet
25 11,480 11.800 11.800 4.050 4.850 5,500 11,480 11,800 11.800
30 8.030 8.600 9,250 2.270 3,070 3.640 8,030 8.600 9,250
35 5,700 6.550 6,950 2,400 5,700 6,550 6.950 SI
40 4.100 4.900 5,500 4,100 4,900 5,500 29.9' (9.1m)
45 3.650 4,250 3.650 4,250
��========:::;tcZ:I:
2 :II I
50 2,720 3.280 2.720 3,280
55 2,000 2,500 2,000 2,500 51.2'(15.6m)
60 1.900 1,900
1,380 8 $ t I I
65 1,380
65'(19.8m)
NOTE.36.900lbs. capacity requires 6 parts of line.
All other capacities for on rubber operation shall be picked using 4 parts of line. $
In the LOAD MOMENT INDICATOR (AML-M), the lifting capacity data based on the 8 /)
80'(24.4m)
II1 l
standard number of part line listed in the chart is stored.

WARNING AND OPERATING INSTRUCTIONS FOR ON RUBBER CAPACITIES

1. Total rated loads on rubber are in pounds and do not exceed 75% of tipping loads as 5. Over front operation shall be performed within two degrees in front of chassis.
determined by test in accordance with SAE J-765. 6. On rubber lifting with "jib" and "auxiliary lifting sheave" (single top) are not permittea.
2. Total rated loads shown in the chart are based on condition that crane is set on firm level 7. When making lift on rubber, set parking brake.
surfaces with suspension lock applied. Those above bold lines are based on 8. For creep operation, boom must be centered over front of machine, swing lock
tire capacity and those below, on crane stability. They are based on actual engaged, and load restrained from swinging. Travel slowly and keep the lifted
load radius increased by tire deformation and boom deflection. load as close to the ground as possible, and especially avoid any abrupt
3. Total rated loads are based on proper tire inflation, capacity and condition. Damaged steering, accelerating or braking.
tires are hazardous to safe operation of crane. 9. Do not operate the crane while carrying the load.
4. Tires shall be inflated to correct air pressure. 10. Creep is motion for crane not to travel more than 200 feet (60 m) in any 30 minute
period and to travel at the speed of less than 1 mph (1.6 km/h).
TIRE AIR PRESSURE
20.50-25-24PR-93psi (6.55 kgf/cm?)

WARNING AND OPERATING INSTRUCTIONS FOR USING THE LOAD MOMENT

INDICATOR (AML-M)
1. When operating crane on outriggers:
• Set P.T.O. switch to "ON". • When a load is lifted in the front position and then swung to the side area,
• Push the outrigger state register switch to illuminate the outrigger indicator make sure the value of the LOAD MOMENT INDICATOR (AML-M) is below
lamps. the 360° lifting capacity.
• Push the boom state register switch repeatedly until the state of the indicator (2) For creep operation.
lamps and the offset display screen conforms to the actual state of the boom, • The creep capacities are attainable only when boom is in the straight forward
the single top and the jib. position of chassis and the over front indicator is on. If boom is not in the
• When erecting and stowing jib, push boom state register switch repeatedly straight forward position of chassis, never lift load.
until jib indicator lamps flicker (in jib erection/stowing mode). 3. During crane operation, make sure that the displays on front panel are in accordance
2. When operating crane on rubber: with actual operating conditions.
• Lock suspension springs with boom over front and crane in traveling 4. The displayed values of LOAD MOMENT INDICATOR (AML-M) are based on freely
configuration. suspended loads and make no allowance for such factors as the effect of wind,
• Set P.T.O. switch to "ON". sudden stopping of loads, supporting surface conditions, inflation of tire,
• Push the boom state register switch repeatedly to illuminate the boom operating speed, side loads, etc.
indicator lamp. For safe operation, it is recommended when extending and lowering boom or swinging,
• Push the on rubber state register switch to illuminate the on rubber indicator lifting loads shall be appropriately reduced.
lamps. By repeatedly pushing the on rubber register switch, stationary and 5. LOAD MOMENT INDICATOR (AML-M) is intended as an aid to the operator. Under
creep operation are selected alternately. When creep operation is selected, no condition should it be relied upon to replace use of capacity charts and operating
the on rubber indicator lamps flicker. instructions. Sole reliance upon LOAD MOMENT INDICATOR (AML-M) aids in place of
However, pay attention to the following. good operating practice can cause an accident. The operator must exercise caution to
(1) For stationary operation. assure safety.
• The front capacities are attainable only when the over front indicator lamp
is on. When the boom is more than 2 degrees from centered over front of
chassis, 360° capacities are in effect.

7
TR-350XL Axle Weight Distribution Chart
Pounds Kilograms
GVW Front Rear GVW Front Rear

Basic standard machine includes:

29.9'-93.8' (9.1-28.6m) 4-section boom
23.6- 42' (7.2-12.8m) 2-stage jib
Main hoist with 574 ft (175m) of 5/8" (16mm) wire
rope 59.966 29,859 30,107 27,200 13,544 13,656
Auxiliary hoist with 295ft (90m) of 5/8" (16mm) wire
rope
35 ton (31.8 metric ton) hookblock
4.4 ton (4 metric ton) hookblock
4170 lbs. (1890kg) counterweight
Mitsubishi 6D16T engine;
20.5 X 25-24 PR tires

Remove:
35 ton (31.8 metric ton) hookblock -750 -1,372 +622 -340 - 622 +282
4.4 ton (4 metric ton) hookblock -220 + 98 -319 -100 + 45 -145

Form No. TA-T35-02 (1M 9212) Printed in Japan