Seat No.: ________ Enrolment No.
___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE - SEMESTER–III (NEW) EXAMINATION – SUMMER 2019
Subject Code: 2131904 Date: 07/06/2019
Subject Name: Material Science and Metallurgy
Time: 02:30 PM TO 05:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
MARKS
Q.1 (a) Answer the following questions. 07
1) What is Embryo?
2) What is strain hardening?
3) Define austenite.
4) Define critical cooling rate.
5) Define phase.
6) Mention any one etchant used for mild steel along with its
chemical composition.
7) Write basic composition of SS304 (Austenitic Stainless Steel).
(b) Explain homogeneous nucleation using concept of free energy 04
change.
(c) Calculate proportion of phases present in 0.2% carbon steel at room 03
temperature using lever rule principle as per Fe-C equilibrium
diagram.
Q.2 (a) Draw Miller indices for planes (0 1 1), (1 0 0) and (1 1 1) and 03
directions [0 1 1], [1 0 0] and [1 1 1] in a simple cubic crystal.
(b) What is red hardness? Explain specific purpose of different alloying 04
elements in 18-4-1 HSS tool steel.
(c) What is pro-eutectoid ferrite? With neat sketch explain step by step 07
solid state transformation of 0.4% carbon steel from single phase
Austenitic temperature to room temperature under equilibrium
condition. Also draw room temperature microstructure and label
phases present in it.
OR
(c) Write Eutectoid reaction for Fe-C binary alloy system. Calculate 07
proportion of phases present in Pearlite. Also explain Austenite to
Pearlite transformation process with neat sketch.
Q.3 (a) Differentiate between deformation by slip and twinning. 03
1
(b) Enlist different methods of preparation of metal powders and 04
discuss characteristics of metal powders used in powder metallurgy.
(c) Draw different heat treatment cooling rate on T-T-T diagram 07
mentioning respective final microstructure for low carbon steel.
Write characteristics of Martensite.
OR
Q.3 (a) Why grain boundary is considered as a crystalline imperfection? 03
(b) What is sintering? Why is sintering carried out in controlled- 04
atmosphere furnace?
(c) What is the effect of carbon and other alloying elements on T-T-T 07
diagram? Explain in detail with neat sketch. What is the importance
of this phenomenon in welding of alloy steels?
Q.4 (a) Write typical composition and application of: 03
1) Cartridge Brass 2) Inconel
(b) Why normalizing produces structure having superior strength and 04
hardness compared to annealing?
(c) Explain mechanical properties and applications of Gray Cast Iron. 07
OR
Q.4 (a) What are the outstanding properties of cupronickel alloys? 03
(b) Write purpose of the case hardening heat treatment and explain any 04
one in detail.
(c) Write short note on Malleable Cast Iron and Nodular Cast Iron. 07
Q.5 (a) What informations may be obtained from an equilibrium diagram? 03
(b) Explain various criterions for selection of material for engineering 04
application.
(c) Explain working principle of Eddy Current Test. Mention various 07
applications of Eddy Current Test.
OR
Q.5 (a) Write limitations of RT and UT. 03
(b) Explain various methods of magnetization used in MPT. 04
(c) Calculate density of copper crystal using following data. 07
Atomic Radius of copper is 1.278 Å, Atomic weight of copper is
63.5 gm/mol. Take Avogadro’s number = 6.023 x 1023.
*************
