Optoisolation and Optical Sensor Products

Selection Guide

Your Imagination, Our Innovation Sense Illuminate Connect

Optoisolation Products 10 11 13 14 17 18 20 21 22 26 27 30 33 36 37 38 39 40 41 43 46 47 52 61 Multi-Channel & Bi-Directional Digital Optocoupler High Speed Digital CMOS Logic Gate Optocoupler 20 MBd Logic Gate Optocoupler 10 MBd Logic Gate/CMOS Optocoupler 8 MBd Logic Gate Optocoupler 5 MBd Logic Gate Optocoupler 1 MBd Transistor Output Optocoupler 100 kBd Darlington Transistor Output Optocoupler R2Coupler (High Temperature, Automotive Grade) Digital Isolator Miniature Analog Isolation Ampli er Integrated Gate Drive Optocoupler Intelligent Power Module Interface Optocoupler Isolated Line Receiver Isolated 20 mA Current Loop Transmitter/Receiver Isolated Voltage/Current Detector High Linearity Analog Optocoupler Wideband Analog/Video Optocoupler General Purpose Phototransistor Optocoupler Solid State Relay (Photo MOSFET) Powerline Communication Interface Hermetic High Performance Optocoupler Package Drawings Function vs Application Matrix

Optical Sensors 63 Proximity and Ambient Light Sensors

Avago Technologies oers the industrys best isolation technology along with the industrys leading CMR performance
Avago Technologies optocouplers can be used in an array of isolation applications ranging from power supply and motor control circuits to data communications and digital logic interface circuits. The primary purpose of an optocoupler is to provide both electrical insulation and signal isolation. The popularity of Avago Technologies optocouplers is due to cost e ective innovations in these areas. Optocouplers eliminate the e ects of electrical noise caused by crosstalk, power glitches and electrical interference. They provide high voltage isolation allowing safe interface between high and low voltages in electrical circuits. They are also used for shifting logic levels. Avago Technologies key products include optocouplers with phototransistor output, digital and analog output, high speed and high gain performance, drivers for isolated gate transistors and intelligent power modules, smart current sensors, solid state relay (Photo MOSFET) and other application speci c devices. Avago Technologies o ers the industrys best isolation technology along with the industrys leading CMR performance of up to 40 kV/s in a broad line of packages. Products include the lowest power dissipation with input current as low as 40 A, high speed digital optocouplers operating at up to 50 MBd, propagation delays as low as 22 ns, 3.3 V JEDEC compatible optocouplers. Avago Technologies optocouplers are manufactured with high quality and reliability and have worldwide safety approvals including the highest maximum insulation voltage (VIORM) at 2262 V (per IEC/EN/DIN EN 60747-5-2/5).

Avago Technologies o ers a broad range of isolation products that provide performance features and bene ts that are unmatched in the industry for industrial, computing, consumer, communication, medical, military and aerospace markets.
Applications for Avago Technologies Isolation Products
Industrial
The widest portfolio of optocouplers to meet the extensive requirements of applications in factory automation. Automated test equipment Battery operated vehicle Fieldbus Industrial communications Industrial networking Motor control PLC input/output isolation Power distribution systems Power generation Renewable energy power generation Robotics Switching panel Switching power supplies Test and measurement equipment

Medical
Avago Technologies o ers optocouplers with high linearity and high resolution for severe isolation requirements to: Defibrillators ECG/EKG Endoscopes Magnetic resonance imaging Patient monitoring

Power over ethernet Telephone switching equipment Telephone terminal equipment Wireless base station

Consumer Electronics
Avago Technologies o ers lower solution costs with highly integrated optocouplers for many consumer applications, such as: Air conditioning Alarm systems Audio and video equipment Electronic gaming Fitness equipment Induction cookers Plasma displays Washing machines

Computers and Oice Equipment

Automotive
Avago Technologies automotive R2Coupler are AEC-Q100 quali ed with applications in: Automotive and shipboard system CANBus interface isolation Motor inverter drives DC-DC converters/ inverters for battery chargers Battery/inverter voltage monitoring Status/fault signal feedback isolation interface Heating, ventilation and air-conditioning
4

Avago Technologies optocouplers with CMOS compatibility and high speed are used to provide interface isolation for: Isolated input/output module Isolated USB hub Printers and plotters

Communications
Avago Technologies provides high speed optocouplers in both single and dual surface-mount packages which are used in: Automated metering reading Digital cross connect Distributed power architecture ISDN Modems PBX and central office Power line communication

Military and Aerospace

Avago Technologies high reliability hermetic optocouplers are suitable for military, aerospace and harsh industrial applications such as: Switching power supplies /UPS Motor control Field bus Inverters Power distribution Communications

Avago, Avago Technologes, the A logo, R 2Coupler are trademarks of Avago Technologies in the United States and other countries.

Quick Guide to Direct Upgrades

Upgrade Part Feature Benet

High Voltage Insulation

Improved Isolation/Insulation Ability to protect surrounding circuitry against physical damage resulting from di erential voltages. ACNV family o ers highest available working voltage ratings Meets international safety regulations and standards. with regulatory approval per IEC/EN/DIN EN 60747-5-2/5 of Provides better isolation and overall safety performance. 2262 V peak.

Noise Isolation
High CMR Common-mode transient rejection or signal isolation of data through suppression of noise transients. O ers guaranteed CMR performance up to 40 kV/ s which is the highest available in the market. Improves system performance, and reliability. More robust systems and better data integrity meet EMI and ESD requirements.

Power Consumption
Drive Current, IF Low Drive Current, LED drive current. Lower Power Supply Lower power supply (3.3V) Flexible Supply Voltages (3.3V/5V) O ers the lowest IF (as low as 40 A) devices in the market and broadest HCMOS compatibility. Eliminates additional LED drive circuitry. Improves system e iciency and reduces power consumption and LED degradation.

Lower the power consumption and meets JEDEC low voltage Up to 50% energy saving. requirements. Support a combination of two di erent supply voltages at the Built-in internal level shifter, eliminate the need of extra input and output. power supply. 3.3V or 5V. 3.3V helps to improve the overall power consumption.

Temperature
Temperature The DC, speed performance and the reliability information is ensured at the speci c temperature range. Support up to -55C to 125C temperature range. Allow extreme temperature operation.

Speed Benets
Propagation Delay, tp Describes how quickly a logic signal can propagate through the system. Upgrade Pulse Width Distortion, PWD PWD is the di erence between tPHL and tPHL and often determines the maximum data rate capability of a transmission system. High speed digital optocouplers to meet wide range of applications with tp as low as 22 ns. The lowest PWD o ered by optocoupler is 2 ns. Increase switching efficiency and better speed performance.

To ensure signal data integrity over long bus line.

Packages for Space Savings

Multi-Channels, Bi-directional Features Surface Mount Device SMD permits more component density than DIP. 8mm Clearance/Creepage (C/C) Packages Integrated dual, triple, quad with bi-directional channels o ers in small SO8 and SO16 package. Smaller package to deliver the same functionality as standard DIP. True surface mount technology and standard footprint. The package is 50% smaller than conventional DIP package. It can withstand high isolation voltages and meet regulatory requirements such as IEC/UL/CSA standards. Smaller SO5 package (as compared to existing SO-8 package) The integrated bi-directional channels help in space savings and ease of designs. Lower assembly cost, easier and faster handling as well as better solderability. Provides space savings. Allows high voltage surge protection. Meets many IEC/UL/CSA equipment standards that call for clearance and creepage of 8mm. Provides greater than 40% space savings.

Smaller SO5 Package

Digital Optocouplers
Existing Parts Upgrade Parts Upgrade Features Footprint Information

High Speed Family (>12.5MBd)

HCPL-0708 ACPL-071L Flexible supply voltages (3.3V/5V) Lower Propagation Delay (<40ns) Wide temperature (-40C to 105C) Glitch-Free Output Flexible supply voltages (3.3V/5V) Lower Propagation Delay (<40ns) Wide temperature (-40C to 105C) Glitch-Free Output Flexible supply voltages (3.3V/5V) Lower Propagation Delay (<40ns) Wide temperature (-40C to 105C) Glitch-Free Output Flexible supply voltages (3.3V/5V) Lower Propagation Delay (<40ns) Wide temperature (-40C to 105C) Smaller 8mm C/C package (Stretched SO6) Glitch-Free Output Lower Speed (15MBd)* Flexible supply voltages (3.3V/5V) Lower Propagation Delay (<40ns) Wide temperature (-40C to 105C) Smaller 8mm C/C package (Stretched SO8) Glitch-Free Output Lower Speed (15MBd)* Flexible supply voltages (3.3V/5V) Wide temperature (-40C to 105C) Lower PWD (<6ns) Flexible supply voltages (3.3V/5V) Wide temperature (-40C to 105C) Lower PWD (<6ns) Drop-in replacement

HCPL-0738

ACPL-074L

Drop-in replacement

HCPL-0708

ACPL-M75L

Smaller footprint

HCPL-2400

ACPL-W70L

Smaller footprint

HCPL-2430

ACPL-K73L

Smaller footprint

HCPL-0710/20/21 HCPL-7710/20/21

ACPL-072L ACPL-772L

Drop-in replacement Drop-in replacement

10MBd Family
HCPL-M600/01/11 HCPL-M600/01/11/0L HCPL-0600/01/11/1A/1N/0L HCPL-0630/31/3A/3N HCPL-060L ACPL-W611/W60L/P611 HCPL-2601/11/1A/1N HCPL-260L HCPL-7601/11 ACPL-K63L HCPL-2630/31/3A/3N HCPL-260L HCPL-4661 HCPL-0600/01/11/1A/1N HCPL-M600/01/11 HCPL-2601/11/1A/1N HCPL-260L/3L HCPL-0630/31/3A/3N/61 HCPL-2630/31/3A/3N HCPL-4661 HCPL-7601/11 HCPL-M611 ACPL-M61L ACPL-061L^ ACPL-064L ACPL-W61L More than 80% power saving. Low forward current (If) to allow direct drive from microcontroller. Wider temperature range (-40C to 105C). Wider supply voltage (2.7V-5.5V). CMOS output to eliminate pull-up resistor. Drop-in replacement Drop-in replacement Drop-in replacement Smaller footprint

ACPL-K64L

Smaller footprint

ACSL-6210/6300/6310/6400/6410/6420

Multi-channel, bidirectional Wide temperature (-40C to 100C) Flexible supply voltages (3.3V/5V)

Smaller footprint

ACPL-M61U R2Coupler

Wide temperature (-40C to 125C) Low LED input drive current IF=10mA

Drop-in replacement

Existing Parts

Upgrade Parts

Upgrade Features

Footprint Information

1MBd Family
HCPL-050L/0500/0501 HCPL-053L/0530/0531 6N135, 6N136 HCPL-250L/2502/2503 HCPL-253L/22230/2531/2533 ACPL-M50L ACPL-054L ACPL-W50L ACPL-K54L 80% power consumption saving Low forward current (IF > 3mA min) High CTR rato >90% min @ IF=3mA Wide temperature range (-40C to 105C) Wide supply voltage (2.7V to 24V) Excellent CMR performance 15kV/s @ Vcm 1500V Part specific (For ACPL-W50L/K54L) : Offer higher working insulation voltage 1140Vpeak, isolation voltage, 5000Vrms Smaller footprint Drop-in replacement Smaller footprint Smaller footprint

Powerline Communication Interface

HCPL-0810 / 8100 ACPL-0820 Improved dual channel line driver (SO8) Transmit voltage up to 7Vpp, and higher driving current of up to 1.5App. Pin layout change Smaller footprint

Miniature Analog Isolation Amplier

HCPL-7860 HCPL-786J ACPL-C797 Wide operating temperature (-40 to +105C) More accurate clock (10 MHz 10%) Input offset voltage (0.3 mV typ) Offset drift (1.5 V/C typ) 3V to 5.5V wide supply range for digital interface 0.5%/1%/3% gain accuracy 30% smaller package size 8 mm Creepage and Clearance 1230 Vpeak working insulation voltage 30% smaller package size 8 mm Creepage and Clearance 1140 Vpeak working insulation voltage 3% gain accuracy Smaller footprint

HCPL-7800A/7800/7840

ACPL-C79B/C79A/C790

Smaller footprint

ACPL-C78A/C780/C784

Smaller footprint

HCPL-7520

HCPL-7510

Drop-in replacement

Existing Parts

Upgrade Parts

Upgrade Features

Footprint Information

Integrated Gate Drive Optocoupler

HCPL-3120 ACPL-H312 ACPL-K312 ACPL-312U R2Coupler ACPL-P341 ACPL-W341 ACPL-P343 ACPL-W343 ACPL-H342 ACPL-K342 Smaller package size 8mm Creepage and Clearance (ACPL-K312) Supply current Icc 3mA maximum Extended operating temperature -40C to 125C Up to 4A maximum peak output current Rail-to-Rail output voltage Low Propagation Delay (<200ns) 50% smaller package size Rail-to-Rail output voltage Integrated Active Miller Clamp Lower Propagation Delay Anti-Cross conduction Very High CMR (40kV/s) Very High CMR (40kV/s) Smaller footprint

Drop-in replacement Smaller footprint

Smaller footprint

HCPL-3120 HCPL-J312 HCNW3120

ACPL-3130 ACPL-J313 ACNW3130 ACNW3410^

Drop-in replacement

Rail-to-Rail output voltage Low Propagation Delay Very High CMR 14mm Creepage and 13mm Clearance High Working Voltage VIORM 2262VPEAK High Insulation Voltage VISO 7500VRMS High CMR 40kV/s Low Propagation Delay Very High CMR 50% smaller package size 8mm Creepage and Clearance (ACPL-W302) Integrated Active Miller Clamp Lower Propagation Delay (<250ns) Low PWD (<100ns) Direct LED drive without Buffer 5A maximum peak output current Wide temperature (-40C to 100C)

Drop-in replacement

ACNV3430^

Larger footprint to achieve higher creepage & clearance

HCPL-3140 HCPL-0314 HCPL-J314 HCPL-3020 HCPL-0302 HCPL-316J

ACPL-P314 ACPL-W314 ACPL-P340 ACPL-W340 ACPL-P302 ACPL-W302 ACPL-330J ACPL-331J ACPL-332J ACPL-333J ACNW3190

Smaller footprint Smaller footprint Smaller footprint Pin layout change

HCPL-3120 / HCPL-J312 / HCNW3120 + External Transistor Stage for Higher Current Output

Pin layout change

Note: ^ - Advance information, subject to change without notice.

Existing Parts

Upgrade Parts

Upgrade Features

Footprint Information

Intelligent Power Module Interface Optocoupler

HCPL-4502 HCPL-4503 HCPL-4504 ACPL-K453 ACPL-W454 ACPL-P454 HCPL-4506 ACPL-W456 ACPL-P456 ACPL-4800 ACPL-W480 ACPL-P480 HCPL-M452/3/4/6 ACPL-M484 8mm Creepage and Clearance 50% smaller package size 8mm Creepage and Clearance 50% smaller package size 8mm Creepage 50% smaller package size 8mm Creepage and Clearance 50% smaller package size 8mm Creepage 50% smaller package size 8mm Creepage and Clearance 50% smaller package size 8mm Creepage 50% smaller package size Higher CMR 30kV/s 10MBd speed Totem-pole output, positive logic 8mm Creepage and Clearance Higher CMR 30kV/s 10MBd speed Totem-pole output, positive logic 13mm Creepage and Clearance Higher Working Voltage Viorm 2262Vpk Higher CMR 30kV/s Totem-pole output, positive logic Wide temperature (-40C to 125C) Low LED input drive current IF 10mA Wide temperature (-40C to 125C) Smaller footprint Smaller footprint Smaller footprint Smaller footprint Smaller footprint Smaller footprint Smaller footprint Faster speed

HCPL-4502/03/04/06 HCPL-0452/53/54/66

ACPL-W484

Faster speed

HCNW4502/03/04/06

ACNV4506

Higher Working Voltage

HCPL-M452/53/54 HCPL-M456

ACPL-M43U ACPL-M46U

Drop-in replacement Drop-in replacement

General Purpose Phototransistor Optocoupler

HCPL-817 HCPL-814 HCPL-181/817 ACPL-827 ACPL-847 ACPL-824 ACPL-844 ACPL-217 Multi-channel. 2-ch and 4-ch Multi-channel. 2-ch and 4-ch Smaller package (SO4 half-pitch) CMR 10kV/s (typ) Extended Industrial -55 to 110C Viso 3kVrms (1min) Smaller package (SO4 half-pitch) CMR 10kV/s (typ) Extended Industrial -55 to 110C Viso 3kVrms (1min) Higher Integrations Higher Integrations Smaller footprint

HCPL-354/814

ACPL-214

Smaller footprint

Note: Drop-in replacement means no PCB board redesign is required, Pin-to-Pin means the footprint is same but requires minimum PCB board redesign (eg. Removing of external resistor) * Lower speed ^ Advanced information, may subject to changes.

Optoisolation and Optical Sensor Products

Multi-Channel Bi-Directional Digital Optocoupler

Description
The ACSL-6xx0 series are optoisolated, multi-channel and bidirectional, highspeed optocouplers. Integration of multiple optocouplers in monolithic form is achieved through patented process technology. These devices provide full duplex and bidirectional isolated data transfer and communication capability in compact surface mount packages. They are available in a 15Mbd speed option, wide supply voltage range and wide temperature range. The isolated data acquisition system is ideal for digitizing the output of the sensors that operate in hostile environment. The ADC is a 24-bit sigma delta or fast conversion type, converts the analog voltage to a digital number. The digital number represents the input voltage in discrete steps with nite resolution. The quad-channel and bi-directional, ACSL-6410, provides high CMR of 10kV/s and electrical isolation of 2500Vrms between the host system and the data acquisition circuitry and sensors. The power supply is also isolated, usually via a transformer to isolate the AC line voltage from the DC voltages generated to power the data acquisition system.

Applications
Full duplex communication Isolated line receiver Computer-peripheral interfaces Microprocessor system interfaces Digital isolation for A/D and D/A conversion Switching power supply Instrument input/output isolation Ground loop elimination Pulse transformer replacement

Benets
Higher integration - multi-channel provides small and thin packages for space savings; bi-directional channel facilitates PCB routing Wide voltage supply and temperature provides design exibility

Typical Block Diagram

Sensors VDD2 Quad-Channel and Bi-Di (3/1) ACSL-6410

Typical Power over Ethernet Diagram

Rx ACSL-6420 Host Controller 3.3V 3.3V INT HotSwap Controller Ethernet Switch/ Hub Tx Power over signal pairs RJ45 12C Interface

12C Interface

24-Bit Sigma Delta or Fast Conversion ADC

CLK CS D IN D OUT

Multiplexer

Controller with Serial Data Link Microwire or SPI Compatible Interface VDD1

GND2 SDA

SDA OUT

SDA IN

4.8V Power Supply

SCL

SCL GND1

Power over spare pairs

GND2

GND1

Multi-Channel Bi-Directional Digital Optocoupler Product Selection

Part No. Package Channel Forward Reverse IF(on) Direction Direction mA Min.
NEW NEW NEW NEW NEW NEW

tPLH ns Max. 100 100 100 100 100 100

tPLH ns Max. 100 100 100 100 100 100

PWD tPSK ns ns Max. Max. 35 35 35 35 35 35 40 40 40 40 40 40

VCC V Min. 3 3 3 3 3 3

VCC V Max. 5.5 5.5 5.5 5.5 5.5 5.5

CMR - V/ s@VCM CMR VCM V/ s (Min.) V 10000 10000 10000 10000 10000 10000 1000 1000 1000 1000 1000 1000

VISO VRMS Min. 2500 2500 2500 2500 2500 2500

VIORM V peak 560* 560* 560* 560* 560* 560*

ACSL-6210-00RE ACSL-6400-00TE ACSL-6410-00TE ACSL-6420-00TE ACSL-6310-00TE ACSL-6300-00TE

SO8 SO16 SO16 SO16 SO16 SO16

2 4 4 4 3 3

1 4 3 2 2 3

1 0 1 2 1 0

7 7 7 7 7 7

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060.

10

Optoisolation and Optical Sensor Products

High Speed Digital CMOS Logic Gate Optocoupler

Description
These optocouplers use the latest CMOS IC technology to achieve outstanding performance with very low power consumption. Serial eldbuses are used today primarily as the communication system for the exchange of information between automation system and distributed field devices. PROFIBUS is the leading open eldbus system and it has worldwide acceptance. PROFIBUS is essentially a twisted wire pair serial link that is very similar to RS 485. Pro bus speed standard is either lower speed (1.5 MBd) or higher speed (12 MBd). In this isolated multipoint transmission application circuit, two di erent optoisolators are utilized (HCPL-0721 and HCPL-061N). The bene ts include low input drive current that maximizes LED lifetime/reliability and optimizes speed for Pro bus and RS-485 applications.

Benets
High speed (up to 50 MBd) 3.3V/5V dual supply voltage available Wide temperature operation -40C to 100C (HCPL-x710) Low PWD (2ns) & low tp (22ns) to meet DeviceNet and Pro bus application Buffer input and CMOS output to eliminate any pull-up resistor 5 kV isolation voltage (HCPL-77xx) Dual channel device is available to save space(HCPL-0738) Certified with reinforced insulation under IEC/EN/DIN EN 60747-5-2

Applications
AC plasma display panel level shifting CAN Bus CC_Link Microprocessor system interface Mutiplexed data transmission Switching power supply

Typical Probus Block Diagram

5V 8 0.01F 7 RX 6 5 ACPL-072L 1 2 3 4 ISO 5V 8 7 6 5 SHIELD ACPL-061L^ 5V 1 2 3 4 SHIELD 8 680 7 6 5 0.01 F 3 ISO 5V 2 DE 0.01 F 0.01 F 1 4 R D 75ALS176D B ISO 5V 8 V CC A 6 RT 7 + 0.01F REG ISO 5V ISO 5V

SHIELD ACPL-072L

5V 1 TX 2 3 0.01 F 4

RE

GND 5 0.01 F 1M

TX ENABLE

11

Optoisolation and Optical Sensor Products

High Speed Digital CMOS Optocoupler Product Selection

Device Part No. Package VDD V IF(on) Max Data mA Rate MBd Min. Min. 25 25 25 12.5 25 25 50 12.5 25 25 50 15 tPLH ns Max. 40 40 40 40 40 40 22 40 40 40 22 55 tPHL ns Max. 40 40 40 40 40 40 22 40 40 40 22 55 PWD ns Max. 6 6 6 8 8 6 2 8 8 6 2 25 tPSK ns Max. 20 20 20 20 20 20 16 20 20 20 16 40 CMR - V/ s@VCM CMR VCM V/ s (Min.) V 20000 1000 10000 10000 10000 10000 10000 10000 10000 10000 10000 10000 10000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 VISO VRMS Min. 3750 3750 VIORM V peak 567* 567*

Single Channel CMOS Input ACPL-077L-000E^

VDD1 1 V1 2 3 GND1 4
LED1

SO8 SO8

3.3/5 3.3/5

8 VDD2 7 NC IO 6 VO 5 GND2

ACPL-072L-000E ACPL-772L-000E HCPL-0710 HCPL-0720 HCPL-0721 HCPL-0723 HCPL-7710 HCPL-7720 HCPL-7721 HCPL-7723 ACPL-M75L-000E

SHIELD

300 mil DIP8 3.3/5 SO8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 SO5 5 5 5 5 5 5 5 5 3.3/5 4

3750/5000 # 630* 3750 3750 3750 3750 3750/5000# 3750/5000# 3750/5000# 3750/5000# 3750 567* 567* 567* 567* 630* 630* 630* 630* 567*

V DD1 1 V1 2 3 GND 1 4
LED1

8 VDD2 7 NC IO 6 VO 5 GND

SHIELD

Single Channel LED Input

5 VDD ANODE 1 4 VO

CATHODE 2 3 GND

NC ANODE CATHODE NC

1 2 3 4

ACPL-M75L

8 VDD 7 NC 6 VO 5 GND

ACPL-071L-000E

SO8

3.3/5 10

15

40

40

25

30

10000

1000

3750

567*

ANODE

NC*

HCPL-0708 ACPL=071L

6 VDD

ACPL-W70L-000E

Stretched SO6 3.3/5 4

15

55

55

25

40

10000

1000

5000

1140*

5 VO

CATHODE

3 4 GND

NC ANODE CATHODE NC

1 2 3 4

ACPL-W70L

8 VDD 7 NC 6 VO 5 GND

HCPL-0708

SO8

10

15

60

60

30

40

10000

1000

3750

567*

Dual Channel LED Input HCPL-0708

ACPL=071L
ANODE1 1 8 VDD2 7 VO1 CATHODE1 2 CATHODE2 3 6 VO2 ANODE2 4 5 GND

ACPL-074L-000E

SO8

3.3/5 10

15

40

40

25

30

10000

1000

3750

567*

ANODE 1 1 CATHODE 1 2 CATHODE 2 3 ANODE 2 4

HCPL-0738 ACPL=074L

8 VDD 7 VO1 6 VO2 5 GND

ACPL-K73L-000E

Stretched SO8 3.3/5 4

15

55

55

25

40

10000

1000

5000

1140*

ANODE1 1

ACPL-K73L

8 VDD2 7 V O1

HCPL-0738

SO8

10

15

60

60

30

40

10000

1000

3750

567*

CATHODE1 2 CATHODE2 3 6 V O2 ANODE2 4 5 GND

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL5000VRMS / 1 minute Option 020 HCPL-0738 ACPL=074L ^ - Advanced Information, may subject to changes.

12

Optoisolation and Optical Sensor Products

20 MBd Logic Gate Optocoupler

Description
These optocouplers have high data rate capability and low input current requirements. In analog-to-digital converters, designers should isolate the two portions of a circuit so that interference generated by digital switching and clock signals are not coupled to the analog section. The below gure demonstrates the ability of optocouplers to achieve isolation in a high speed parallel interface data communication application. Optocouplers reduce the channel distortion and thereby maximize the reliability of the circuit.

Benets
Totem pole & tri state output (with enable pin for HCPL-2400) to eliminate output pull-up resistors Certified with reinforced insulation under IEC/EN/DIN EN 60747-5-2/5, approved with Viorm=630Vpeak (option 060) DIP8 package (for min. 7mm creepage/ clearance need) with 5kV Viso protection (option 020) 2-channel for higher integration and space saving (HCPL-2430)

Applications
Computer-peripheral interface High speed disk drive I/O Isolated bus driver (networking applications) Isolation of higher speed logic system Switching noise elimination

Typical Block Diagram

V CC1 ANALOG SIDE HCPL-2400 (4) V CC2 DIGITAL SIDE

V CC A.D CONVERTER (ADC60-08) ANALOG IN

STATUS SERIAL IN A SERIAL OUT CLOCK OUT

EN V CC QA QH
CLEAR GND

END OF CONVERSION

EN

SERIAL IN B

SHIFT REGISTER (74164)

8-BIT DIGITAL DATA DATA ACCEPTED BEGIN CONVERSION

EN
GND CONVERT

CLOCK IN

EN

20 MBd Logic Gate Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. 4 tPLH ns Max. 60 tPLH ns Max. 60 PWD ns Max. 25 tPSK ns Max. 35 CMR - V/ s@VCM CMR VCM V/ s (Min.) V 1000 300 VISO VRMS Min. 3750 VIORM V peak 630*

Single Channel 1 NC
ANODE 2 1 NC CATHODE 3 ANODE 2 4 NC CATHODE 3 4 NC

VCC 8 VCC 7 VE 8 6 VO 7 VE 5 GND 6 VO GND 5

HCPL-2400

300 mil DIP8

Dual Channel
ANODE 1 1 CATHODE 1 2 ANODE 1 1 CATHODE 2 3 CATHODE 1 2 ANODE 2 4 CATHODE 2 3 ANODE 2 4 8 VCC 7 VO1 8 VCC 6 VO2 7 VO1 5 GND 6 VO2 5 GND

HCPL-2430

300 mil DIP8

60

60

25

35

1000

300

3750

630*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060

13

Optoisolation and Optical Sensor Products

10 MBd Logic Gate/ CMOS Optocoupler

Description
This isolated RS-422 circuit uses two high-speed optocouplers that can switch up to 10 MBd signals. An isolated power supply VCC2 is required to power the DS 75176A driver/receiver integrated circuit. The main benefit is preventing commonmode transients from interfering with the signal. Avagos new range of 3.3 V/5 V optocouplers are the rst commercially available optocouplers designed to meet the JEDEC speci cation for 3.3 V LVTTL/LVCMOS logic, thereby simplifying the implementation of isolation in systems utilizing 3.3 V logic circuits. A typical Power over Ethernet power source equipment (PSE) block diagram uses two 15 MBd 3.3 V optocouplers to isolate between the 13 W 48 V power supply and the inter-integrated chip (I2C) control bus.

Applications
Computer-peripheral interface Instrument input/output isolation Isolated line receiver Microprocessor system interface Switching power supply

Benets
Provides high data rate transmission. It also o er high CMR for signal isolation from common mode transient noises

Typical RS-422 Interface Block Diagram

Typical Power over Ethernet Power Source Block Diagram

14

Optoisolation and Optical Sensor Products

10 MBd Logic Gate Optocoupler Product Selection

Device Part No. Package VDD V 3.3/5 5 5 5 5 5 5 3.3/5 3.3/5 5 5 5 5 5 5 5 5 5 3.3/5 5 5 5 5 5 5 IF(on) mA Min. 5 5 5 5 5 5 5 5 5 3 3 5 5 5 5 5 3 3 5 5 5 5 5 5 5 tPLH ns Max. 90 100 100 100 100 100 100 90 90 100 100 100 100 100 100 100 100 100 90 100 100 100 100 100 100 tPHL ns Max. 75 100 100 100 100 100 100 75 75 100 100 100 100 100 100 100 100 100 75 100 100 100 100 100 100 PWD ns Max. 25 35 35 35 40 40 40 25 25 45 45 35 35 35 35 35 45 45 25 35 35 35 35 40 40 tPSK ns Max. 40 40 40 40 40 40 40 40 40 60 60 40 40 40 40 40 60 60 40 40 40 40 40 40 40 CMR - V/ s@VCM CMR V/ s VCM V (Min.) 15000 10000 10000 1000 5000 10000 15000 15000 15000 1000 1000 5000 15000 15000 10000 15000 1000 1000 15000 15000 5000 10000 20000 20000 1000 1000 1000 10 1000 1000 1000 1000 1000 50 1000 1000 1000 1000 1000 1000 50 1000 1000 1000 50 1000 1500 1500 VISO VRMS Min. 5000 5000 5000 3750/5000 # 5000 5000 5000 3750 3750/5000 # 3750 3750 3750 3750 3750 3750/5000 # 3750/5000 # 3750/5000 # 3750/5000 # 3750 3750 3750 3750 3750 7500 5000 VIORM V peak 1140* 891* 1140* 630* 1414 1414 1414 567* 630* 567* 567* 567* 567* 567* 630* 630* 630* 630* 567* 2262 ATEX (375V) 1140* 567* 567* 567* 567* 567* 567* 630* 630* 630* 630* 630* 630*

Single Channel
ANODE 1
2 6 5 SHIELD 4

ACPL-W60L-000E
VCC VO GND

Stretched SO6 Stretched SO6 Stretched SO6 300 mil DIP8 400 mil DIP8 400 mil DIP8 400 mil DIP8 SO8 300 mil DIP8 SO8 SO8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 SO5 SO5 SO5 SO5 SO5 500 mil DIP10 500 mil DIP10

ACPL-P611-000E ACPL-W611-000E 6N137 HCNW137 HCNW2601 HCNW2611 HCPL-060L HCPL-260L HCPL-061A HCPL-061N HCPL-0600 HCPL-0601 HCPL-0611 HCPL-2601 HCPL-2611 HCPL-261A HCPL-261N ACPL-M60L-000E ACPL-M61U-000E HCPL-M600 HCPL-M601 HCPL-M611 ACNV2601-000E ACNV260E-000E

CATHODE 3

NC 1 ANODE 2 CATHODE 3 NC 4
SHIELD

8 7 6 5

VCC VE VO GND

ANODE 1 CATHODE 3

6 V CC 5 V out 4 GND

ANODE 1 1 CATHODE 1 2 CATHODE 2 3 ANODE 2 4

SHIELD

8 7 6 5

VCC VO1 VO2

GND

NC 1 ANODE 2 ANODE 1 CATHODE 3 NC CA CATHODE 34

SHIELD

VCC

7 VE 6 VCC 6 VO 5 VO

GND 4 5 GND

NC 1 ANODE 2 1 ANODE CATHODE 3 CATHODE 3 NC 4 NC 5

10

VCC

NEW NEW

96 VE CC
5 8 4 7

VO VO

SHIELD

GND GND NC

Dual Channel
ANODE 1 1 CATHODE 1 2 CATHODE 2 3 ANODE 2 4
SHIELD 8 7 6 5

VCC
VO1 VO2

GND

ACPL-K63L-000E HCPL-063A HCPL-063L HCPL-063N HCPL-0630 HCPL-0631 HCPL-0661 HCPL-263A HCPL-263L HCPL-263N HCPL-2630 HCPL-2631 HCPL-4661

Stretched SO8 SO8 SO8 SO8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8

3.3/5 5 3.3/5 5 5 5 5 5 3.3/5 5 5 5 5

5 3 5 3 5 5 5 3 5 3 5 5 5

90 100 90 100 100 100 100 100 90 100 100 100 100

75 100 75 100 100 100 100 100 75 100 100 100 100

25 45 25 45 35 35 35 45 25 45 35 35 35

40 60 40 60 40 40 40 60 40 60 40 40 40

15000 1000 15000 15000 5000 10000 15000 1000 15000 15000 5000 10000 15000

1000 50 1000 1000 1000 1000 1000 50 1000 1000 1000 1000 1000

5000 3750 3750 3750 3750 3750 3750 3750/5000 # 3750/5000 # 3750/5000 # 3750/5000 # 3750/5000 # 3750/5000 #

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000V RMS/1 minute Option 020, ^ - Advanced information, may subject to changes.

15

Optoisolation and Optical Sensor Products

3.3V/5V Family (10 MBd CMOS Optocoupler)

Device Part No. Package VDD V 3.3/5 IF(on) mA Min. 1.6 Max. Data Rate MBd Min. 10 tPLH tPHL PWD ns ns ns Max. Max. Max. 80 80 30 tPSK ns Max. 30 CMR - V/ s@VCM CMR VCM V/ s (Min.) V 20000 1000 VISO VRMS Min. 3750 VIORM V peak 567*

Single Channel LED Input

NC ANODE CATHODE NC 1 2 3 4 8 VDD 7 VE

ACPL-061L-000E^

NEW

SO8

6 VO 5 GND

ACPL-C61L-000E^
HCPL-0708 ACPL=071L

ACNW261L-000E^ ACPL-W61L-000E
5 VDD

NEW

Stretched SO8 400 mil DIP8 Stretched SO6 SO5

3.3/5 3.3/5 3.3/5

2.5 2.5 1.6

10 10 10

100 100 80

100 100 80

40 40 30

40 40 30

20000 20000 20000

1000 1000 1000

5000 5000 5000

1230* 1414* 1140*

ANODE 1 4 VO

CATHODE 2 3 GND

ACPL-M61L-000E

NEW

3.3/5

1.6

10

80

80

30

30

20000

1000

3750

567*

ACPL-M75L
6 VDD ANODE 1 5 CATHODE 3 4 GND VO

ACPL-M62L-000E^

SO5

3.3/5

1.6

10

80

80

30

30

20000

1000

3750

567*

Dual Channel LED Input ACPL-M62L

ANODE1 1 8 VDD2 7 VO1 CA CATHODE1 2 CA CATHODE2 3 6 VO2 ANODE2 4 5 GND

ACPL-064L-000E

NEW

SO8

3.3/5

1.6

10

80

80

30

30

20000

1000

3750

567*

ACPL-K64L-000E

NEW

Stretched SO8

3.3/5

1.6

10

80

80

30

30

20000

1000

5000

1140*

Notes: * - with IEC/EN/DIN EN 60747-5-2 Option 060, # - with UL 5000V RMS /1 minute Option 020, ^ - Advanced Information, may subject to changes.

16

Optoisolation and Optical Sensor Products

8 MBd Logic Gate Optocoupler

Description
The circuit shows a CMOS interface circuit for 8 MBd applications. Over the temperature range a CMOS CD4050 Hex Bu er can source about 0.7 mA (minimum), which is sufficient to drive the HCPL-2300 optocoupler. The 20 pF capacitor allows peaking currents to assist the LED in turning on and o quickly. These optocouplers utilize a simple interface requiring low power consumption.

Benets
Offers low power consumption

Applications
Computer-peripheral interface Digital isolation for A/D, D/A conversion High speed, long distance isolated line receiver Level shifting RS 232C interface

Typical CMOS Interface Block Diagram

8 MBd Logic Gate Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. 0.5 tPLH s Max. 0.16 tPHL s Max. 0.2 CMR - V/ s@VCM CMR V/ s (Min.) 100 VCM V 50 VISO VRMS Min. 3750 VIORM V peak

Single Channel
1
Anode 2 Cathode 3

HCPL-0300
8 VCC 7 RL 6 VD 5 GND

SO8

HCPL-2300

300 mil DIP8

0.5

0.16

0.2

100

50

3750

630*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060

17

Optoisolation and Optical Sensor Products

5 MBd Logic Gate/CMOS Optocoupler

Description
The circuit shown in the typical TTL interface block diagram is an interface between two TTL gates using an active output (totem pole) optocoupler, the HCPL-2201. A series switching circuit drives the optocoupler LED. The active output HCPL-2201 can be directly connected to a TTL gate, and no pull-up resistor is required. The HCPL-2201 can sink enough current to handle up to 16 LSTTL or 4 TTL loads. Typically, the 5 MBd logic gate optocoupler is used in the Isolated High-Low Gate Drive interface block diagram as shown below.

Benets
Pull up resistor not required at the optocoupler output Low power on the optocoupler input circuit Wide operating supply voltages up to 20V Built-in Schmitt Triggers for better signal integrity and accuracy in a noisy network/ circuits.

Applications
Computer-peripheral interface Ground loop High speed line receiver Microprocessor system interface Pulse transformer replacement

Typical TTL Interface Block Diagram

HCPL-2219/2200

Isolated High-Low Gate Drive Interface Block Diagram

Output (AC-DC) Transformer DC Output DC Bus Power Switch Output Recti er

Gate Driver

PWM Controller

Digital Optocoupler

Control Circuit

18

Optoisolation and Optical Sensor Products

5 MBd Logic Gate Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.8 1.8 tPLH s Max. 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 tPHL s Max. 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 CMR - V/ s@VCM CMR V/ s (Min.) 1000 10000 1000 10000 1000 10000 2500 1000 1000 10000 1000 10000 VCM V 50 1000 50 1000 50 1000 400 50 50 1000 50 1000 VISO VRMS Min. 5000 5000 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 VIORM V peak 1414 1414 560* 560* 630* 630* 630* 630* 630* 630*

Single Channel
NC 1 ANODE 2 CATHODE 3 NC 4 SHIELD 8 VCC 7 VO 6 NC 5 GND

NC 1 ANODE 2 CATHODE 3 NC 4 SHIELD

8 VCC 7 VO 6 VE 5 GND

HCNW2201 HCNW2211 HCPL-0201 HCPL-0211 HCPL-2201 HCPL-2211 HCPL-2219 HCPL-2200 HCPL-2202 HCPL-2212 HCPL-2231

400 mil DIP8 400 mil DIP8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8

NC 1 ANODE 2 CATHODE 3 NC 4 SHIELD

8 VCC 7 NC 6 VO 5 GND

Dual Channel
ANODE 1 1 CATHODE 1 2 CATHODE 2 3 ANODE 2 4
SHIELD

8 VCC 7 VO1 6 VO2 5 GND

HCPL-2232

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060

5 MBd CMOS Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. 1.6 tPLH s Max. 0.25 tPHL s Max. 0.25 CMR - V/ s@VCM CMR V/ s (Min.) 25000 VCM V 1000 VISO VRMS Min. 3750 VIORM V peak 560 *

Single Channel
ANODE 1 6 VDD

ACPL-M21L

NEW

SO5

VO

CATHODE

Shield

GND

ANODE

VDD

ACPL-W21L ^

Stretched SO6

1.6

0.25

0.25

25000

1000

5000

1140*

NC

VO

CATHODE

Shield

GND

Dual Channel
ANODE 1 1 8 VDD

ACPL-024L ^ ACPL-K24L ^

SO8 Stretched SO8

1.6 1.6

0.25 0.25

0.25 0.25

25000 25000

1000 1000

3750 5000

560 * 1140*

CATHODE 1 2

V01

CATHODE 2 3

V02

ANODE 2 4

Shield

GND

NC 1 ANODE 2 CATHODE 3 NC 4

8 VDD 7 VO 6 5 GND

ACPL-021L ^

SO8

1.6

0.25

0.25

25000

1000

3750

560*

Shield

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes.

19

Optoisolation and Optical Sensor Products

1 MBd Transistor Output Optocoupler

Description
The circuit in the level shifting/TTL interface block diagram shows how a 0 to 5 V logic signal can be level shifted to a -15 to 0 V signal. This circuit can safely be used for level shifting up to 800 V. The circuit uses an open collector output logic gate, the 74LS405, to drive the LED of the 6N135/6 optocoupler. The 6N135/6 also has an opencollector output. The designer chooses RIN to agree with the equation shown in the schematic. This equation sets the value of the optocoupler LED forward current. The output of the 6N135/6 requires a pull-up resistor, RL. The current-transfer ratio (CTR) of the optocoupler determines the maximum amount of current the optocoupler output can sink while maintaining the output voltage (between pins 5 and 6) of 0.5 V or less. The bene t of the application is that it reduces the transient immunity problem and it is a convenient way of replacing the pulse transformer for high-voltage level shifting.

Benets
Allow level shifting capability High current transfer ratio

Applications
Analog signal ground isolation High speed logic ground isolation Line receivers Replace pulse transformers Replace slow phototransistor isolators

Typical Level Shifting/TTL Interface Block Diagram

+5 V HCPL-050L R IN IF
74LS05

IO (min) = I F CTR (min) 8 R L (min) = 15 VOL IO (min) + I IL RL IO I IL

V IN

3 R IN = 5 - V F IF

6 V OL

V OUT

-15 V

1 MBd Transistor Output Optocoupler Product Selection

Device Part No. Package VDD V
3.3/5

Max VDD V
24

IF(on) mA Min.
3

Single Channel
1 6 5

ACPL-M50L-000E

SO5

% Min.
80

CTR % Max.
200

IF mA
3

tPLH s Max.
1.0

tPHL s Max.
1.0

CMR - V/ s@VCM CMR VCM V/ s (Min.) V

15000

VISO VRMS Min.

3750

VIORM V peak
560*

1000

ACPL-W50L-000E

Stretched SO6

3.3/5

24

53

200

1.0

1.0

15000

1000

5000

1140*

V CC

Anode 2 Cathode 3
4

7 NC 6 VO 5 GND

Dual Channel
Anode 1 1 Cathode1 2 Cathode2 3 Anode 2 4
8 7 6 5

VCC V01 V02 GND

6N135 6N136 HCNW135 HCNW136 HCPL-050L HCPL-0500 HCPL-0501 HCPL-250L HCPL-2502 HCPL-2503 ACPL-054L-000E ACPL-K54L-000E HCPL-053L HCPL-0530 HCPL-0531 HCPL-253L HCPL-2530 HCPL-2531 HCPL-2533

300 mil DIP8 300 mil DIP8 400 mil DIP8 400 mil DIP8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 SO8 Stretched SO8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8

5 5 5 5 3.3/5 5 5 3.3/5 5 5 3.3/5 3.3/5 3.3/5 5 5 3.3/5 5 5 5

15 15 15 15 15 15 15 15 15 15 24 24 15 15 15 15 15 15 15

16 16 16 16 16 16 16 16 16 8 3 3 16 16 16 16 16 16 8

7 19 5 19 15 7 19 15 15 15 53 53 15 7 19 15 7 19 15

50 50 50 50 50 50 50 22 200 200 50 50 50 50 50 50

16 16 16 16 16 16 16 16 16 8 3 3 16 16 16 16 16 16 8

2.0 1.0 2.0 1.0 1.0 2.0 1.0 1.0 0.8 2.5 1.0 1.0 1.0 2.0 1.0 1.0 2.0 1.0 2.5

2.0 1.0 2.0 1.0 1.0 2.0 1.0 1.0 0.8 1.5 1.0 1.0 1.0 2.0 1.0 1.0 2.0 1.0 1.5

1000 1000 1000 1000 1000 1000 1000 1000 15000 15000 1000 1000 1000 1000 1000 1000

10 10 10 10 10 10 10 10 1000 1000 10 10 10 10 10 10

3750/5000 # 3750/5000 # 5000 5000 3750 3750 3750 3750/5000 # 3750/5000 # 3750/5000 # 3750 5000 3750 3750 3750 3750/5000 # 3750/5000 # 3750/5000 # 3750

630* 630* 1414 1414 560* 560* 560* 630* 560* 1140* 560* 630*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000V RMS/1 minute Option 020, ^ - Advanced information, may subject to changes.

20

Optoisolation and Optical Sensor Products

100 kBd Darlington Transistor Output Optocoupler

Description
This di erentially driven circuit can use up to eight 6N138 optocouplers at various receivers along the 90 m line. All stations are isolated. The rst station would draw approximately 2.7 mA current, and the last station 1.8 mA of LED drive current. The output grounds of the optocoupler may be electrically separate. The bene t of the application is its simple, low-cost, multidrop circuit for low signaling rates.

Benets
High CTR with low input current Low power consumption

Applications
NC V Digital logic ground ANODE V isolation V CATHODE NC GND FIA RS-232C line receiver Low power systems and ANODE V ground isolation CATHODE V Telephone ringV detector CATHODE
1
8

CC E

Typical Multidrop Line Receiver Block Diagram

6N138 1/2 DM8830 UP TO 90 m 22 GA TW. PR. SHIELDED 39 X Y 560 IF 39 1 Y X 2 Y X 3 Y X 6 Y X 7 Y X 8 Y X 3 4 6 5 VO 1 2 8 7 2.2 k +5 v

1 1 2

CC O1 O2

ANODE 2 4

GND

100 kBd Darlington Transistor Output Optocoupler Product Selection

NC 1
8 7 6 SHIELD 5

VCC

ANODE 2 CATHODE Device

3

VE VO GND

NC 4

Part No.

Package

VDD V 5 5 5 5 5 5 5 3.3/5 5 5 3.3/5 5 5 5 5 3.3/5 5 5 3.3/5 5 5 5

IF(on) mA Min. 0.5 0.5 0.5 0.5 0.5 0.5 0.04 0.5 0.5 0.5 0.5 0.04 0.5 0.5 0.04 0.5 0.5 0.5 0.5 0.5 0.5 0.04

CTR % Min. 200 200 300 400 300 400 800 400 300 400 400 800 300 400 800 400 400 400 400 400 400 800 % Max. 1000 1000 2600 5000 25000 5000 2600 5000 5000 25000 2600 3500 25000 5000 5000 5000 5000 5000 5000 25000 IF mA 10 10 1.6 0.5 1.6 0.5 0.04 0.5 1.6 0.5 0.5 0.04 1.6 0.5 0.04 0.5 0.5 0.5 0.5 0.5 0.5 0.04

tPLH tPHL CMR - V/ s@VCM s s VCM Max. Max. CMR V/ s (Min.) V 500 500 50 90 70 11 25 90 50 10 90 90 35 10 130 90 35 35 90 35 60 90 50 50 15 2 11 11 60 30 15 2 30 25 20 2 25 30 20 20 30 20 20 25 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

VISO VRMS Min. 3750 3750 3750/5000 # 3750/5000 # 5000 5000 3750 3750 3750 3750 3750/5000 # 3750/5000# 3750 3750 3750 3750 3750 3750 3750/5000 # 3750/5000# 3750/5000# 3750/5000#

VIORM V peak 630 630 630* 1414 1414 560* 560* 560* 560* 630* 630* 560* 630* 21

Single Channel CATHODE

1 2
ANODE CATHODE 21 3 CATHODE

ANODE 1 1

8 7

VCC VO1
O2

4N45
TRUTH TABLE (POSITIVE LOGIC) LED ON

300 mil DIP6 300 mil DIP6 300 mil DIP8 300 mil DIP8 400 mil DIP8 400 mil DIP8 SO8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 SO5 SO8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8

6 VV 6 B

ANODE 2 4
2

SHIELD

5 VO

GND

4N46
L H

OUTPUT

4 GND

OFF

** JEDEC Registration Data ** JEDEC Registered up to 70C

CATHODE 3

Cathode 3
NC 4 4

1 8 VCC NC 1 4N45/4N46 8 VCC 7 VB 7 VE 2 ANODE

Anode 2

6 VO VO

55

GND GND

ANODE 1 1 CATHODE 1 2 CATHODE 2 3 ANODE 2 4

8 7 6 5

VCC VO1 VO2

Anode 1

6 5

VCC

GND

Cathode 2

Vout 4 GND

Anode 1 Cathode 2

6 5 4

VCC Vout GND

6N138 6N139 HCNW138 HCNW139 HCPL-070A HCPL-070L HCPL-0700 HCPL-0701 HCPL-270L HCPL-4701 HCPL-M700 HCPL-073A HCPL-073L HCPL-0730 HCPL-0731 HCPL-273L HCPL-2730 HCPL-2731 HCPL-4731

HCPL-M701 SO5

Dual Channel
Anode 1 1 Cathode 1 2 Cathode 2 3 Anode 2 4
8 7 6 5

VCC V01 V02 GND

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000V RMS /1 minute Option 020

Optoisolation and Optical Sensor Products

R2Coupler (High Temperature, Automotive Grade)

Description Proven Quality and Reliability Track Record
Avago Technologies R2Coupler isolation products are designed to meet the stringent requirements for the automotive market. Building upon 35 years of optocoupler expertise, the automotive parts are manufactured in a TS 16949 certi ed manufacturing facility and are PPAP supported. Robustness is demonstrated through quali cation in accordance to AECQ100 Grade 1 guidelines. Avago optocouplers have been used extensively in long life and mission critical isolation applications such as locomotive transportation, aerospace, military and industrial automation. Since the introduction of R2Coupler products in 2006, these automotive grade products have seen wide adoption by many automotive suppliers with millions of units operating in the eld.

Benets
Qualified to AEC-Q100 Grade 1 guidelines TS 16949 manufacturing facility with PPAP support Wide operating temperature (-40C to 125C) High CMR (30 kV/s at VCM =1kV) Reinforced Reliability suitable for automotive applications Low input LED drive current Worldwide Safety Approval (UL1577, IEC60747-5-5, CSA)

Applications
Automotive IPM and gate driver for inverters, DC-DC converter and on-board chargers Automotive bus voltage and current/voltage sensing in inverters, converters and on-board chargers Automotive CANbus, UART, LIN and other digital communications Isolated wake-up and status control and feedback Analog feedback in AC-DC and DC-DC converters Low power digital isolation in battery management systems

Technology Leader
Avago Technologies is the rst supplier to introduce 125C plastic optocouplers for automotive applications, with the largest portfolio of optocouplers ranging from IGBT gate drivers, isolation ampli er, high speed and low power digital isolation and analog feedback isolation. Advanced LED technology enabled the best-in-class performance over lifetime and at high temperature. These optocouplers maintain their very high voltage ratings with robust and reliable galvanic isolation technology with international component safety certi cations (UL1577, IEC 60747-5-5, CSA Component Notice 5). Optocouplers demonstrate superior EMI and common mode noise immunity.

22

Optoisolation and Optical Sensor Products

Typical Intelligent Power Module/Electric Motor Inverter Block Diagram

Automotive CANBus Block Diagram

Bus Interface MicroController

CAN Transceiver
Ground Vout Vcc

Other Devices Rx

Other Devices

Cathode

Anode

Tx
Ground Cathode Anode Vout Vcc

ACPL-M61T/M71T/M72T UART Network Controller

Controlled Devices, e.g. Air-Compressor, Lighting Control, Battery Management System, etc.

Automotive 10MBd Logic Gate Optocoupler

Device Single Channel
Anode 1
6 VDD 5 VO

Part No. ACPL-M71T ACPL-K71T^ ACPL-M72T ACPL-K72T^

Package VISO (1min) VRMS SO5 SSO8 SO5 SSO8 SSO8 SSO8 4000 5000 4000 5000 5000 5000

VIORM V peak 560 1140 560 1140 1140 1140

Operating Temperature C -40 to 125 -40 to 125 -40 to 125 -40 to 125 -40 to 125 -40 to 125

VCC V 3.0 to 5.5 3.0 to 5.5 3.0 to 5.5 3.0 to 5.5 3.0 to 5.5 3.0 to 5.5

ILED mA

IDD mA

tPLH tPHL PWD tPSK CMR Max. Max. Max. Max. dV/dt ns ns kV/ s 35 35 100 100 35 100 35 35 100 100 35 100 12 12 50 50 12 50 15 15 60 60 15 60 15 15 25 25 15 25

VCM V 1000 1000 1000 1000 1000 1000

4 to 15 1.5 4 to 15 1.5 4 to 15 1.5 4 to 15 1.5 4 to 15 1.5 4 to 15 1.5

Cathode 3

4 GND

Dual Channel LED Input

Anode 1 1 Cathode 1 2 Cathode 2 3 Anode 2 4 8 VDD2 7 VD1 6 VD2 5 GND

ACPL-K74T^ ACPL-K75T^

Anode 1 Cathode 3

6 VCC 5 VO
SHIELD

ACPL-M61T

SO5

4000

560

-40 to 125

4.5 to 5.5

5 to 15 13

100

100

35

40

15

1000

4 GND

Note: ^ - Advanced information, may subject to changes.

23

Optoisolation and Optical Sensor Products

Automotive 1MBd Transistor Output Optocoupler

Device Single Channel
Anode 1 Cathode 3
6 VCC 5 VO
SHIELD

Part No. ACPL-M46T

4 GND

Package VISO VRMS SO5 4000

VIORM Operating VCC V Temperature V peak C 560 -40 to 125

ILED mA

CTR Min. % 44

CTR Typ. % 90

tPHL tPHL PWD tPSK CMR Max. Max. Max. Max. dV/dt s s s s kV/ s 0.55 0.55 0.45 0.45 15

CMR VCM V 1500

4.5 to 30 10 to 20

6 5

ACPL-M43T ACPL-K43T ACPL-M49T ACPL-K49T ACPL-K44T

8 VCC 7 VD1 6 VD2 5 GND

SO5 SSO8 SO6 SSO8 SSO8

4000 5000 4000 5000 5000

560 560

-40 to 125 -40 to 125

20 20 20 20 20

5 to 15 0.8 to 15 4 to 10 4 to 10 0.8 to 15

20 24 20 24 20

45 65 58 58 65

1 1 100 100 1

1 1 100 100 1

0.45 0.45 0.45 0.45 0.45

0.5 0.5 0.5 0.5 0.5

15 15 15 15 15

1500 1500 1500 1500 1500

1140 -40 to 125 1140 -40 to 125 1140 -40 to 125

Dual Channel
Anode 1 1 Cathode 1 2 Cathode 2 3 Anode 2 4

Automotive Analog Optocoupler

Device Part No. Package VISO VRMS SO5 SSO8 SO5 SSO8 4000 5000 4000 5000 VIORM V peak 560 1140 560 1140 Operating VCC Temperature V C -40 to 125 -40 to 125 -40 to 125 -40 to 125 20 20 20 20 ILED mA 5 to 15 0.8 to 15 4 to 10 4 to 10 CTR Min. % 20 24 20 24 (TA = 25 C) Typ. % 45 65 45 58 Min. % 32 32 32 32 BW Typ. kHz CMR dV/dt kV/ s CMR VCM V 1500 1500 1500 1500

6 5

ACPL-M43T ACPL-K43T ACPL-M49T ACPL-K49T

1000 15 1000 15 15 15

Automotive Gate Drive Optocoupler

Device Features Part No. Package VISO VRMS SO16 5000 VIORM Operating VCC V Temperature V peak C 1230 -40 to 125 ILED Typ. mA lo_ ICC tPHL tPHL PWD tPSK CMR peak Max. Max. Max. Max. Max. dV/dt Max. mA ns ns ns ns kV/ s A 5 500 500 300 350 15 CMR VCM V 1500

VLED1+VLED1
7 8

VIN+ 2 VIN 3 VCC1 4 RESET 65 FAULT 1 GND1

LED1

D R I V E R SHIELD LED2

UVLO

DESAT

VCC2 VC VOUT 14 DESTAT 9, 12 VEE

13 11 10 16

Desat, ACPLUVLO, Fault 38JT Feedback Rail-to-Rail, ACPLDesat, UVLO, 34JT^ Fault Feedback, Miller Clamp UVLO ACPL312T

15 to Buffered 2.5 30

FAULT SHIELD 15

VE

VLED2+

VE VCC2 NC NC VCC1 Input Driver Output Driver

SO16

5000

1230 -40 to 125

VLED+
UVLO

UVLO FAULT VEE1 AN CA

15 to 10 to 16 25

2.5

250

250

30

1500

Over Current

DESAT VOUT

SS Control Miller Control

SS/CLAMP

N/C 1 Anode 2 Cathode 3 N/C 4

8 7 6 5

VCC VO VO VEE

DIP8

3750

630

-40 to 125

15 to 7 to 16 30

2.5

500

500

300

350

15

1500

Note: ^ - Advanced information, may subject to changes.

24

Optoisolation and Optical Sensor Products

Automotive Miniature Analog Isolation Amplier

Device Features Part No. Package VISO VRMS DIP8 VIORM Operating VDD V Temperature V peak C -40 to 125 4.5 to 5.5 Input Range Typ. V 0.2 Gain Typ. V/V 8 Gain NonL O- BW Tol Max. set Typ. Max. % Max. kHz % mV 2 0.35 4 100 CMR dV/dt kV/ s 10 CMR VCM V 1000

VDD1 1 VIN+ 2 VIN 3 GND1 4

IDD1 +

IDD2 + SHIELD

8 VDD2 7 VOUT+ 6 VOUT 5 GND2

2% Gain Accuracy

ACPL-782T

4000 891

VDD1 1 VIN 2 SD 3 GND1 4 SHIELD

8 VDD2 7 VOP 6 VON 5 GND2

DC Voltage Sensing, Shut-down Control

ACPL-C87AT^

SSO8

5000 1140 -40 to 125 5000 1140 -40 to 125

4.5 to 5.5 4.5 to 5.5

0 to 2 0 to 2

1 1

1 0.5

0.35 0.35

20 20

100 100

15 15

1000 1000

ACPL- C87BT^ SSO8

Note: ^ - Advanced information, may subject to changes.

Extended Temperature R2Coupler

Device Part No. Package Operating IOUT A Temperature (MAX) C -40 to 125 NA IF mA CTR tPLH tPHL PWD tPSK s s ns ns % % Min. Max. Max. Max. Max. Max. 32 80 1.0 1.0 850 NA CMR V/ s (Min.) 15000 CMR - V/ s@VCM VISO VRMS VCM Min. V 1500 VIORM V peak

6 5

ACPL-M43U-000E

NEW

SO5

10

3750 567

Anode 1 Cathode 3

6 VCC 5 VO
SHIELD

ACPL-M46U-000E

NEW

SO5

-40 to 125

NA

10

44

90

0.4

0.6

450.0 NA

15000

1500

3750 567

4 GND

ANODE 1 CA CATHODE 3

6 VCC 5 VO 4 GND

ACPL-M61U-000E

NEW

S05

-40 to 125

NA

NA

NA

0.1

0.1

35

40

15000

1000

3750 567

N/C 1 Anode 2 Cathode 3 N/C 4

8 7 6 5

VCC VO VO VEE

ACPL-312U-000E

NEW

DIP6

-40 to 125

2.5

N/A

N/A

0.5

0.5

300

350 (PDD)

25000

1500

3750 630

25

Optoisolation and Optical Sensor Products

Digital Isolator
Description Applications
Digital fieldbus isolation Multiplexed data transmission Computer peripheral interface High speed digital systems Isolated data interfaces Logic level shifting The ACML-74xx series of CMOS digital isolators utilizes magnetic coupling through thick insulation to provide high speed, high insulation performance yet consuming low power at high data rates. The HCPL-90xx/-09xx series CMOS digital isolators integrated with giant magnetoresistive (GMR) technology enable high speed performance and excellent transient immunity speci cations. All devices operate at 3.3 V or 5 V supply voltages, boasting low power consumption. They are able to withstand high common mode voltages, 25kV/s at Vcm=1000V, and meet UL 1577 and IEC 60950-1, IEC 61010-1 and IEC 60601-1 safety ratings.

Benets
High insulation: UL1577 (5.6kVrms 1 min rating) and IEC 60950-1 and IEC 61010-1 working voltage (up to 1132Vpeak) High speed (100MBd), low PWD (3ns) and low Tp (18ns) Wide temperature operation (-40C to 105C) Buffer input and CMOS output (eliminate input/output resistors) Multi-channel (1, 2 & 4-ch) Low power consumption

Bridge

Serial Data In Data Clock Chip Select

Isolation Barrier

Typical Isolated A/D Conversion Block Diagram

ACML-7410 HCPL-092J HCPL-902J Bridge + A/D Serial Data Out

To P

Digital Isolator ACML-74XX, HCPL-09XX AND HCPL-90XX Product Selection

Device Part No. Channel Package Max . Data Rate MBd Min. 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 tPLH & tPHL (VCC=5.0V) ns Max. 15 15 15 15 15 15 32 15 15 32 15 15 32 15 15 tPLH & tPHL (VCC=3.3V) ns Max. 18 18 18 18 18 18 36 18 18 36 18 18 36 18 18 PWD ns Max. 3 3 3 3 3 3 2 3 3 2 3 3 2 3 3 tPSK ns Max. 6 6 6 6 6 6 5 6 6 5 6 6 5 6 6 CMR - V/ s@VCM CMR V/ s (Min.) 15000 15000 15000 15000 15000 15000 25000 15000 15000 25000 15000 15000 25000 15000 15000 VCM V 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 VISO VRMS Min. 2500 2500 2500 2500 2500 2500 5600 2500 2500 5600 2500 2500 5600 2500 2500

IN1 2 NC 3 GND1 4

Galvanic Isolation

DD1 1

8 VDD2 V 7 VOE 6 OUT1 5 GND2

IN1 2 IN2 3 GND1 4

Galvanic Isolation

V VDD1 1

8 VDD2 7 OUT1 6 OUT2 5 GND2

IN1 2 OUT OUT2 3 GND1 4

Galvanic Isolation

V VDD1 1

8 VDD2 7 OUT1 6 IN2 5 GND2

HCPL-0900 HCPL-9000 HCPL-0930 HCPL-9030 HCPL-0931 HCPL-9031 ACML-7400 HCPL-090J HCPL-900J ACML-7420 HCPL-091J HCPL-901J ACML-7410 HCPL-092J HCPL-902J
NEW NEW NEW

Single Single Dual Dual Dual, Bi-Dir Dual, Bi-Dir Quad Quad Quad Quad, 2/2, Bi-dir Quad, 2/2 Bi-dir Quad, 2/2 Bi-dir Quad, 3/1, Bi-dir Quad, 3/1 Bi-dir Quad, 3/1 Bi-dir

SO8 300 mil DIP8 SO8 300 mil DIP8 SO8 300 mil DIP8 SO16 Wide Body SO16 Narrow Body SO16 Wide Body SO16 Wide Body SO16 Narrow Body SO16 Wide Body SO16 Wide Body SO16 Narrow Body SO16 Wide Body

VDD1 1 GND1 2 Galvanic Isolation IN 1 3 IN 2 4 IN 3 5 IN 4 6 NC 7 GND1 8

16 VDD2 V 15 GND2 14 OUT1 13 OUT2 12 OUT3 11 OUT4 10 NC 9 GND2

V VDD1 1 GND1 2 Galvanic Isolation IN 1 3 IN 2 4 OUT3 5 OUT4 6 NC 7 GND1 8 1

16 VDD2 V 15 GND2 14 OUT1 13 OUT2 12 IN 3 11 IN 4 10 NC 9 G GND2

V VDD1 1 GND1 2 Galvanic Isolation IN 1 3 IN 2 4 IN 3 5 OUT OUT4 6 NC 7 GND1 8

16 VDD2 V 15 GND2 14 OUT1 13 OUT2 12 OUT3 11 IN4 10 NC 9 GND2

26

Optoisolation and Optical Sensor Products

Miniature Analog Isolation Amplier

Description Benets
Compact package suitable for high volume production process Cost-effective solution Reinforced insulation The ACPL-C79B/C79A/C790 isolation ampli ers are designed for current and voltage sensing in electronic power converters in applications including motor drives and renewable energy systems. Based on sigma-delta analog-to-digital converters, these isolation ampli ers feature high gain accuracy, low temperature drift of -50ppm/C, 3.3V/5V output supply operation and a wide -40 to +105C operating temperature range. These features are delivered in a SSO-8 package that has a footprint 30% smaller than the standard DIP-8 package. When mounted on a PCB, it occupies a space that is a fraction of that for a traditional Hall E ect current transducer. The series is implemented with a fully di erential circuit with gain accuracy of 0.5% (ACPL-C79B), 1% (ACPL-C79A), and 3% (ACPL-C790). With a 200kHz bandwidth and 1.6s response time, the ACPL-C79x captures transients during short circuit and overload conditions. Operating from a single 5V supply, the isolation ampli er series features an excellent nonlinearity of 0.05% and a SNR of 60dB.

Applications
Motor phase and rail current sensing Data acquisition systems Inverter current sensing General purpose current sensing and monitoring

Example Application: Block diagram of a micro-inverter with simplied DC-DC-AC topology.

CHARGE CONTROLLER / DC-DC CONVERTER HV+ INVERTER DC-AC VOLTAGE SENSOR ACPL-C79B/C79A/C790

SOLAR PANEL GATE DRIVER ACPL-H342/K342 GATE DRIVERS ACPL-H342/K342, 4X GATE DRIVERS

VOLTAGE SENSOR

TO POWER GRID CURRENT SENSOR

CURRENT SENSOR ACPL-C79B/ C79A/C790

HV

PWM DSP

PWM

ACPL-M61L, 2X

FIELD BUS COMMUNICATION

27

Optoisolation and Optical Sensor Products

Miniature Isolation Amplier

Device Part No. Features Package Operating Gain Error NonBandVDD2 Temperature at 25C linearity width V C % Typ. % Typ. kHz Typ.
-40 to +85 -40 to +85 -40 to +85 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +105 -40 to +105 -40 to +105 1 3 5 0.5 1 3 0.5 1 3 1 3 5 3 5 3 5 3 1 0.5 0.0037 0.0037 0.0037 0.05 0.05 0.05 0.05 0.05 0.05 0.0037 0.0037 0.0037 0.06 0.06 0.06 0.06 0.04 0.04 0.04 100 100 100 200 200 200 200 200 200 100 100 100 30 30 100 100 100 100 100 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 3 - 5.5 3 - 5.5 3 - 5.5 3 - 5.5 3 - 5.5 3 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 3 .3 3 .3 3 .3

CMR - V/ s@VCM VISO VRMS CMR VCM Min. V V/ s (Typ.)

15000 15000 15000 15000 15000 15000 15000 15000 15000 15000 15000 15000 25000 25000 15000 15000 15000 15000 15000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 5000 5000 5000 5000 5000 5000 5000 5000 5000 3750 3750 3750 5000 5000 3750 3750 5000 5000 5000

VIORM V peak
1230* 1230* 1230* 1230 1230 1230 891 891 891 891 891 891* 1230 1230* 891* 891* 1230 1230 1230

VDD1 1 VIN+ 2 IN+ VIN 3 IN GND1 4

IDD1 DD1 +

IDD2 + SHIELD

8 VDD2 7 VOUT+ 6 VOUT 5 GND2

ACPL-C78A ACPL-C780 ACPL-C784 ACPL-C79B ACPL-C79A ACPL-C790 ACPL-790B ACPL-790A ACPL-7900 HCPL-7800A HCPL-7800 HCPL-7840
NEW NEW NEW NEW NEW NEW

200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Di erential Outputs 200mV Inputs, Onboard Fault Detection 200mV Inputs, Onboard Fault Detection 200mV Inputs, Single-ended Outputs 200mV Inputs, Single-ended Outputs

SSO8 SSO8 SSO8 SSO8 SSO8 SSO8 DIP8 DIP8 DIP8 DIP8 DIP8 DIP8 SO16 SO16 DIP8 DIP8

CH CL VDD1 VLED+ VDD1 GND1

VIN+ VIN-

1 2 3 4 5 6 7 8

16 15 14 13 12 11 10 9

GND2 VDD2 FAULT FAULT AUL ABSV ABSVAL VOUT VREF VDD2 GND2

HCPL-788J ACPL-785J HCPL-7510 HCPL-7520 ACPL-C870^

VDD1 1 VIN+ 2 VIN 3 GND1 4

IDD1 +

IDD2 + SHIELD

8 VDD2 7 VOUT 6 VREF 5 GND2

VDD1 1 VIN 2 SD 3 GND1 4 SHIELD

8 VDD2 7 VOP 6 VON 5 GND2

0-2V High Impedence Inputs, SSO8 Di erential Outputs 0-2V High Impedence Inputs, SSO8 Di erential Outputs 0-2V High Impedence Inputs, SSO8 Di erential Outputs

ACPL-C87A^ ACPL-C87B^

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information.

28

Optoisolation and Optical Sensor Products

Isolated Sigma-Delta Modulator

Device Part No. Features Package Operating Gain Error Temperature at 25C C % Typ.
-40 to +105 1

INL LSB Typ.

3

ENOB Bits Typ.

12

VDD2 V

CMR - V/ s@VCM VISO VRMS CMR VCM Min. V V/ s (Typ.)

25000 1000 5000

VIORM V peak
1230*

VDD1 1 VIN+ 2 VIN 3 GND1 4 NC 5 NC 6 VDD1 7 GND1 8 CLK DET. CLK IN MOD. DATA OUT

16 GND2 15 NC 14 VDD2 13 MCLKIN 12 NC 11 MDAT 10 NC 9 GND2

ACPL-796J-000E External Clocked, 5 - 20MHz

SO16

3 - 5.5

DD1 1 VIN+ 2 IN+ VIN 3 IN NC 4 NC 5 NC 6 NC 7 GND1 8

ACPL=796J
SIGMADELTA MOD./ ENCODER

16 GND2 15 NC 14 VDD2

HCPL-786J

DECODER

13 MCLK 12 NC 11 MDAT 10 NC 9 GND2

Internally Clocked, 10MHz

SO16

-40 to +85

11

4.5 - 5.5

20000

1000

5000

1230

ISOLATION BOUNDARY VDD1 1 VIN+ 2 + VIN 3 GND1 4

SIGMADELTA MOD./ ENCODE DECODE

8 VDD2 7 MCLK 6 MDAT 5 GND2

ACPL-C797 ACPL-7970 HCPL-7860 HCPL-7560

NEW NEW

Internally Clocked, 10MHz Internally Clocked, 10MHz Internally Clocked, 10MHz Internally Clocked, 10MHz Modulator Clock Input, Programmable Conversion Modes

SSO8 DIP8 DIP8 DIP8 SO16

-40 to +105 -40 to +105 -40 to +85 -40 to +85 -40 to +85

1 1

3 3

12 12 11 8

3 - 5.5 3 - 5.5 4.5 - 5.5 4.5 - 5.5

25000 25000 20000 20000

1000 1000 1000 1000 NA

5000 5000 3750 3750 NA

1230 891 891 891* NA

SHIELD

1 (Matching) 3 5 64

CCLK CLAT CDAT MCLK1 MDAT1 MCLK2 MDAT2 GND

1 2 3 4 5 6 7 8
CH2 CONFIG. INTERFACE CONVERSION INTERFACE

16 VDD 15 CHAN

HCPL-0872

14 SCLK 13 SDAT
12 CS

CH1 THRESHOLD DETECT & RESET

Dual, Programmable Digital Filter with SPI Interface

4.5 - 5.5 NA

11 THR1

10 OVR1 9
RESET

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes, - VDD

29

Optoisolation and Optical Sensor Products

Integrated Gate Drive Optocoupler

Description
In typical motor drive and renewable energy power conversion systems, there are several signals between the power devices and the micro-controller that need isolation and additional customized functions such as gate drive and current/voltage sensing. Avago Technologiesgate drive and isolation ampli er products provide low cost, high performance solutions for such applications. High performance motor drives require precision timing for turning on and o the power devices on the inverter while renewable energy inverter needs to be reliable and efficient when converting DClink voltage to usable AC power output. The microcontroller that controls these functions needs to be isolated from the high voltage inverter side. Avago Technologies o ers a variety of optocouplers that have builtin gate drive capability. These gate drive optocouplers come in wide range of output current from 0.4A to 5A, and selected parts with integrated protection features such as Active Miller Clamp, under voltage lockout, fault Status feedback and desaturation detection. For solutions that require lower output power capability, IPM interface optocouplers will meet the need.

Applications
Isolated IGBT/MOSFET gate drive AC and brushless DC motor drives Renewable energy inverters Industrial inverters Switching power supplies Uninterruptible power supplies (UPS)

Benets
Rail-to-rail output voltage for reliable IGBTs drive Integrated fault protection and feedback to reduce component count and solution cost Short propagation delay for faster switching Fast IGBT switching for improved efficiency Low power consumption for bootstrap operation High common mode transient rejection ensures reliable operation under noisy environment Direct drive of high power IGBTs Reinforced insulation

Typical Motor Drive Block Diagram

RECTIFIER AC-DC CHARGE CONTROLLER / DC-DC CONVERTER INVERTER DC-AC VOLTAGE SENSOR ACPL-C79B/C79A/C790

GATE DRIVE ACPL-332J R S T VOLTAGE SENSOR GATE DRIVE ACPL-332J

CURRENT SENSOR, 3X

CURRENT SENSOR ACPL-C79B/C79A/C790

MICRO CONTROLLER

30

Optoisolation and Optical Sensor Products

Integrated Gate Drive Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. lOUT A Min. lOUT A Max. tPLH s Max. tPHL s Max. PDD s Max. VCC V Max. CMR - V/ s@VCM CMR VCM V/ s (Min.) V VISO VRMS Min. VIORM V peak

Single Channel
NC ANODE CATHODE NC NC 1 2 3 4 5 10 VCC 9 8 7 6 VOUT NC VEE NC

ACNV3430-000E^ NEW 500 mil DIP

10

2.0

2.5

0.50

0.50

0.35

30

40000

1500

7500

2262

N/C

VCC VOUT N/C

ACNW3410-000E^ NEW 400 mil DIP

2.0

2.5

<0.50

<0.50

<0.35

30

40000

1500

5000

1414

ANODE

CATHODE

N/C

VEE

ANODE

VCC

ACPL-P343-000E ACPL-W343-000E ACPL-P341-000E ACPL-W341-000E ACPL-P340-000E ACPL-W340-000E ACPL-H342-000E ACPL-K342-000E ACPL-312U-000E

NEW NEW NEW NEW NEW NEW NEW NEW

Stretched SO6 Stretched SO6 Stretched SO6 Stretched SO6 Stretched SO6 Stretched SO6 Stretched SO8 Stretched SO8 300 mil DIP

7 7 7 7 7 7 7 7 7

3.0 3.0 2.5 2.5 0.8 0.8 2.0 2.0 2.0

4.0 4.0 3.0 3.0 1.0 1.0 2.5 2.5 2.5

0.20 0.20 0.20 0.20 0.20 0.20 0.35 0.35 0.5

0.20 0.20 0.20 0.20 0.20 0.20 0.25 0.25 0.5

0.1 0.1 0.1 0.1 0.1 0.1 -0.2 -0.2 0.35

30 30 30 30 30 30 30 30 30

35000 35000 35000 35000 35000 35000 40000 40000 25000

1500 1500 1500 1500 1500 1500 1500 1500 1500

3750 5000 3750 5000 3750 5000 3750 5000 3750

891* 1140* 891* 1140* 891* 1140* 891* 1140* 630

N/C

VOUT

CATHODE

VEE

ANODE

VCC

NC

VOUT

CATHODE

VCLAMP
NC 4

VCLAMP

VEE

N/C 1 Anode 2 Cathode 3 N/C 4

8 7 6 5

VCC VO VO VEE
13 VCC2

NEW

UVLO ANODE CATHODE 6, 7 5, 8 LED1 D R I V E R

11 14 DESAT 9, 12

VOUT DESAT

ACPL-330J-000E ACPL-331J-000E

NEW

SO16

1.0

1.5

0.25

0.25

0.15

30

50000

1500

5000

1230

SHIELD VCLAMP VCC1 FAULT 2 3 LED2 16 10

VEE

VCLAMP VE

1.5A Highly Integrated Gate Drive Optocoupler with Active Miller Clamp, Over-Current Protection and Fault Feedback Under Voltage Lock-Out Protection (UVLO) with Hysteresis Automatic Fault Reset after fixed delay time (for ACPL-330J-000E only)
NEW

VS

1, 4 SHIELD

15

VLED

ACPL-332J-000E ACPL-333J-000E

SO16

2.0

2.5

0.25

0.25

0.15

30

50000

1500

5000

1230

2.5A Highly Integrated Gate Drive Optocoupler with Active Miller Clamp, Over-Current Protection and Fault Feedback Under Voltage Lock-Out Protection (UVLO) with Hysteresis Automatic Fault Reset after fixed delay time (for ACPL-333J-000E only). Stretched SO8 Stretched SO8 Stretched SO6 Stretched SO6 Stretched SO6 Stretched SO6 400 mil DIP8 7 7 7 8 7 8 10 2.0 2.0 0.2 0.4 0.2 0.4 4.0 2.5 2.5 0.4 0.6 0.4 0.6 5.0 0.5 0.5 0.7 0.7 0.7 0.7 0.5 0.5 0.5 0.7 0.7 0.7 0.7 0.5 0.35 0.35 0.5 0.5 0.5 0.5 0.3 30 30 30 30 30 30 30 15000 15000 10000 25000 10000 25000 15000 1500 1500 1000 1000 1000 1000 1500 3750 5000 3750 3750 5000 5000 5000 891* 1140* 891* 891* 1140* 1140* 1414

1 2 3 4

8 7 6 5

ACPL-H312-000E ACPL-K312-000E
6 VCC 5 VO

ANODE

ACPL-P302-000E ACPL-P314-000E ACPL-W302-000E ACPL-W314-000E ACNW3190-000E

N.C. 2 CATHODE 3 SHIELD

4 VEE

N/C 1 ANODE 2 CATHODE 3 N/C 4 SHIELD

8 VCC 7 VO 6 VEE 5 VEE

31

Optoisolation and Optical Sensor Products

Integrated Gate Drive Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. lOUT A Min. lOUT A Max. tPLH s Max. tPHL s Max. PDD s Max. VCC V Max. CMR - V/ s@VCM CMR VCM V/ s (Min.) V VISO VRMS Min. VIORM V peak

1 ANODE 2 CATHODE 3 N/C 4

N/C

8 VCC 7 N/C 6 VO

ACNW3130-000E ACPL-3130-000E ACPL-J313-000E ACPL-T350-000E HCNW3120 HCPL-J312 HCPL-J314 HCPL-T250 HCPL-T251 HCPL-0302 HCPL-0314 HCPL-3020 HCPL-3120 HCPL-3140 HCPL-3150 HCPL-3180 HCPL-316J

400 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 400 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 SO16

10 7 7 7 10 7 8 7 8 7 8 7 7 8 7 10

2.0 2.0 2.0 2.0 2.0 2.0 0.4 0.5 0.1 0.2 0.4 0.2 2.0 0.4 0.5 2.0 2.0

2.5 2.5 2.5 2.5 2.5 2.5 0.6 1.5 0.4 0.4 0.6 0.4 2.5 0.6 0.6 2.5 2.5

0.5 0.5 0.5 0.5 0.5 0.5 0.7 0.5 1.0 0.7 0.7 0.7 0.5 0.7 0.5 0.2 0.5

0.5 0.5 0.5 0.5 0.5 0.5 0.7 0.5 1.0 0.7 0.7 0.7 0.5 0.7 0.5 0.2 0.5

0.35 0.35 0.35 0.35 0.3 0.35 0.5 0.5 0.5 0.5 0.35 0.5 0.35 0.09 0.3

30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 20 30

40000 40000 40000 15000 25000 25000 25000 5000 10000 10000 25000 10000 25000 25000 15000 10000 15000

1500 1500 1500 1500 1500 1500 1500 600 600 1000 1000 1000 1500 1000 1500 1500 1500

5000 3750 3750 3750 5000 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 5000

1414 630* 1230^ 630* 1414 1230^ 891 630* 566* 566* 630* 630* 630* 630* 630* 1230

SHIELD

5 VEE

VIN+ VINVCC1 GND1 RESET FAULT VLED1+ VLED1-

1 2 3 4 5 6 7 8

16 15 14 13 12 11 10 9

VE VLED2+ DESAT VCC2 VC VOUT VEE VEE

Dual Channel
N/C 1 ANODE 2 CATHODE 3 SHIELD 16 VCC 15 VO 14 VEE 11 VCC 10 VO SHIELD 9 VEE

HCPL-314J HCPL-315J

2.0 A Highly Integrated Gate Drive Optocoupler with over-current Protection and Fault Feedback CMOS compatible Under Voltage Lock-Out Protection (UVLO) with Hysteresis SO16 8 0.4 0.6 0.7 0.7 0.5 30 25000 1500 SO16 7 0.5 0.6 0.5 0.5 0.35 30 15000 1500

5000 5000

1230 1230

ANODE 6 CATHODE 7 N/C 8

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes.

32

Optoisolation and Optical Sensor Products

Intelligent Power Module Interface Optocoupler

Description
The ACNV/HCNW/HCPL-45xx and ACPL48xx series optocouplers are designed for Intelligent Power Module (IPM) drive applications such as inverters and motor control systems. These high speed optocouplers have high CMR performance that helps to reject common mode noise in such high voltage systems. The output of HCNW/HCPL-45xx devices is conventional open-collector; the output of ACPL-48xx devices came with totem pole output stage eliminates the necessity of using the pull-up resistor and allows direct drive to the IPM. ACNV45xx devices allow very high working voltage for use in Renewable Energy Supply system. In addition to Intelligent Power Module drive, the ACNV/HCNW/HCPL-45xx and ACPL-48xx series optocouplers can be used in general purpose isolation applications like high speed logic ground isolation, isolated line receivers, and microprocessor system interfaces.

Applications
Intelligent power module Inverter/Motor control Power switch design General purpose digital isolation

Benets
Short propagation delay for faster switching Fast IGBT switching for improved efficiency High Common Mode Transient Rejection ensures reliable operation under noisy environment Wide operating temperature range Reinforced insulation

Typical Level Shifting/TTL Interface Block Diagram

+5V RIN 74LS05 IF 1 20K 2 3 5 - VF RIN = IF 4 5 9 8 7 6 IO VOL IL VOUT IO (min) = IF CTR (min) VOL = 15 RL {IO (min) + IIL} =15-RL {IF CTR (min) + IIL} ACNV4506 10 +15V

VIN

SHIELD

NOTE: FOR BEST CMR PERFORMANCE, CONNECT PIN 6 TO PIN 7

Intelligent Power Module (IPM) Based Inverter Block Diagram

VCC IN_UH MCU AND PWM GENERATOR U W V W M HV+ CURRENT SENSE

HVIC GATE DRIVE

HVIC GATE DRIVE

ACPL-M484/P484/W484, OR ACPL-M483/P483/W483 FOR PHASES U, V AND W IN_UL GND

VCC

COMMON 15V TO 20V POWER SUPPLY

HVIC GATE DRIVE

IPM

HV

33

Optoisolation and Optical Sensor Products

Intelligent Power Module Interface Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. 4 CTR % Min. 44 % Max. IF mA 10 tPLH s Max. 0.12 0.12 0.12 0.12 0.12 0.12 0.55 tPHL s Max. 0.12 0.12 0.12 0.15 0.15 0.15 0.40 PDD s Max. 0.10 0.10 0.10 0.13 0.13 0.13 0.50 CMR - V/ s@VCM CMR V/ s (Min.) 30000 30000 30000 30000 30000 30000 30000 VCM V 1000 1000 1000 1000 1000 1000 1500 VISO VRMS Min. 3750 3750 5000 3750 3750 5000 7500 VIORM V peak 567* 891* 1140* 567* 891* 1140* 2262*

Single Channel

ACPL-M483-000E ACPL-P483-000E ACPL-W483-000E ACPL-M484-000E ACPL-P484-000E ACPL-W484-000E ACNV4506-000E

NEW NEW NEW NEW NEW NEW NEW

SO5

Stretched SO6 4 Stretched SO6 4 SO5 4 Stretched SO6 4 Stretched SO6 4 500 mil DIP10 10

NC
Anode Cathode

1 2 3 4

8 7 6 5

V CC
NC
VO

ACPL-4800-000E

300 mil DIP8

0.35

0.35

0.25

30000

1000

3750

630*

NC

SHIELD

GN D

6 5

ACPL-M43U-000E

SO5

10

32

80

10

0.9

15000

1000

3750

567*

Anode 1 Cathode 3

6 VCC 5 VO
SHIELD

ACPL-M46U-000E

SO5

10

44

90

10

0.4

0.55

0.45

15000

1000

3750

567*

4 GND

ACPL-P456-000E ACPL-W456-000E ACPL-P480-000E ACPL-W480-000E ACPL-P481-000E ACPL-W481-000E

NC 1 Anode 2 Cathode 3 NC 4
SHIELD
8

Stretched SO6 10 Stretched SO6 10 Stretched SO6 6 Stretched SO6 6 Stretched SO6 6 Stretched SO6 6 Stretched SO8 16

44 44 19

>90 >90 50

10 10 16

0.55 0.55 0.35 0.35 0.35 0.35 1.00

0.45 0.45 0.35 0.35 0.35 0.35 1.00

0.45 0.45 0.25 0.25 0.25 0.25 1.00

15000 15000 20000 20000 20000 20000 15000

1500 1500 1000 1000 1000 1000 1500

3750 5000 3750 5000 3750 5000 5000

891* 1140* 891* 1140 891* 1140* 1140*

VCC

ACPL-K453-000E

7 NC 6 VO 5 GND

Anode 1 NC 2 Cathode 3
SHIELD

V CC

ACPL-P454-000E ACPL-W454-000E

Stretched SO6 12 Stretched SO6 12

26 26

65 65

12 12

1.14 1.14

1.00 1.00

1.30 1.30

15000 15000

1500 1500

3750 5000

891* 1140*

5 VO 4 GND

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000V RMS/1 minute Option 020, ^ - Advanced information, may subject to changes.

34

Optoisolation and Optical Sensor Products

Intelligent Power Module Interface Optocoupler Product Selection

Device Part No. Package IF(on) mA Min. 16 16 12 16 16 12 16 16 12 12 10 10 10 10 16 16 12 10 16 16 CTR % Min. 19 19 25 19 19 26 19 19 26 21 44 44 44 44 20 20 26 44 19 19 % Max. 50 50 65 50 50 65 50 50 65 65 >90 >90 >90 >90 50 50 65 >90 50 50 IF mA 16 16 12 16 16 12 16 16 12 12 10 10 10 10 16 16 12 10 16 16 tPLH s Max. 1.0 1.0 1.4 1.0 1.0 1.4 1.0 1.0 1.4 0.7 0.55 0.55 0.55 0.55 1.0 1.0 1.4 0.55 1.0 1.0 tPHL s Max. 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.5 0.40 0.48 0.40 0.40 1.0 1.0 1.0 0.40 1.0 1.0 PDD s Max. 1.3 1.0 1.0 1.3 1.3 0.45 0.45 0.45 1.0 1.3 0.45 CMR - V/ s@VCM CMR V/ s (Min.) 1000 15000 15000 1000 15000 15000 1000 15000 15000 15000 15000 15000 15000 15000 1000 15000 15000 15000 15000 15000 VCM V 10 1500 1500 10 1500 1500 10 1500 1500 1500 1500 1500 1500 1500 10 1500 1500 1500 1500 1500 VISO VRMS Min. 5000 5000 5000 3750 3750 3750 3750/5000 # 3750/5000 # 3750/5000 # 3750 5000 3750 3750/5000 # 3750 3750 3750 3750 3750 3750 3750/5000 # VIORM V peak 1414 1414 1414 560* 560* 560* 630* 630* 630* 891 1414 560* 630* 891 567* 567* 560* 560* 560* 630*

VCC

Anode 2 Cathode 3
4

7 NC 6 VO 5 GND

NC 1 Anode 2 Cathode 3 NC 4
SHIELD

20 k W

8 7 6 5

VCC VL VO GND

Anode 1

V CC

5 VO

Cathode 3

SHIELD

4 GND

HCNW4502 HCNW4503 HCNW4504 HCPL-0452 HCPL-0453 HCPL-0454 HCPL-4502 HCPL-4503 HCPL-4504 HCPL-J454 HCNW4506 HCPL-0466 HCPL-4506 HCPL-J456 HCPL-M452 HCPL-M453 HCPL-M454 HCPL-M456 HCPL-0534

400 mil DIP8 400 mil DIP8 400 mil DIP8 SO8 SO8 SO8 300 mil DIP8 300 mil DIP8 300 mil DIP8 300 mil DIP8 400 mil DIP8 SO8 300 mil DIP8 300 mil DIP8 SO5 SO5 SO5 SO5 SO8 300 mil DIP8

Anode 1 Cathode 3

6 VCC 5 VO
SHIELD

4 GND

Dual Channel
Anode 1 1 Cathode 1 2 Cathode 2 3 Anode 2 4
8 7 6 5

VCC V01 V02 GND

HCPL-4534

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000V RMS/1 minute Option 020, ^ - Advanced information, may subject to changes.

35

Optoisolation and Optical Sensor Products

Isolated Line Receiver

Description
The HCPL-2602/12 have input current regulators and integrated high gain photo detectors. The input regulator serves as a line terminator for line receiver applications. The higher LED threshold voltage provides improved immunity to di erential noise and the rejection internally shielded detector provides better common-mode rejection with no sacri ce in speed. The diagram below illustrates an unbalanced line receiver using the integrated voltageclamp input optocoupler, HCPL-2602. TTL data is converted to a di erentia lsignal viathe di erential line driver, and transmitted over twisted-pair wire. The Schottky diode helps to improve the turnon and turn-o delays.

Benets
Line termination included no extra circuitry required

Applications
Isolated line receiver Computer-peripheral interface Microprocessor system interface Digital isolation for A/D, D/A conversion Current sensing Instrument Input/Output isolation Ground loop elimination Pulse transformer replacement Power transistor isolation in motor drives

Typical Block Diagram

+5V 1/2 9614 16 1 5 6 2 4 3 BELDEN 8777 8

HABT-5400
l
R

1 2 3 4

V CC 8 7
.0 .01 F 390

+5V

VN

6
15 pF

VO

GND
HCPL-2602/12

Line Receiver Product Selection

Device Part No. Package Output Collector Output mA Max. 50 50 tPLH s Max. 100 100 tPHL s Max. 100 100 CMR - V/ s@VCM CMR V/ s (Min.) 1000 3500 VCM V 50 300 VISO VRMS Min. 3750 3750

HCPL-2602
NC 1 IN+ 2 IN 3 CATHODE 4 8 7 6 5 VCC VE VO GND

300 mil DIP8 300 mil DIP8

HCPL-2612

SHIELD

40 ns max propagation delay skew (part to part) Line termination circuitry included

36

Optoisolation and Optical Sensor Products

Isolated 20 mA Current Loop Transmitter/Receiver

Description Applications
Isolated 20 mA current loop transmitter in: Industrial control equipment Computer peripherals Data communications equipment Data transmission between electronic equipment which are physically separated by a distance of more than a few feet can be achieved by using the HCPL4100 (transmitter) and the HCPL-4200 (receiver) optocouplers. These devices include specialized circuits for 20 mA digital current loop applications, and are designed to easily interface TTL and CMOS logic systems to current loop systems. 20 mA current loop systems conventionally signal a logic high state by transmitting 20 mA of loop current, and signal a logic low state by allowing no more than few milliamperes of loop current. Optical coupling loops break ground loops and provide very high immunity to common mode interference. These devices are simple to use in a data transmission system for industrial applications and maintain integrity.

Benets
Direct control of the 20 mA current loop High noise immunity

Typical Block Diagram

HCPL-4100 Transmitter
I CC V CC II VI 6 8 3 IO I+ II I+
+

HCPL-4200 Receiver
ICC 8 V CC IO 7 2 SHIELD 5 6 VO 1

VI

+
VO

I-

GND 5 SHIELD 4 I IO

VE IE GND

20 mA Current Loop Transmitter/Receiver Product Selection

Device Part No. Package Data Rate kBd @ (meters) Transmitter
NC 1 NC 2 I+ 3 I- 4 8 VCC 7 6 VI 5 GND

tPLH s Max. 1.6

tPHL s Max. 1.0

CMR - V/ s@VCM CMR V/ s (Min.) 1000 VCM V 50

VISO VRMS Min. 3750

HCPL-4100

300 mil DIP8

20 (400)

CMOS compatible data input for HCPL-4100

Receiver
I+ 1 I- 2 NC 3 NC 4 8 VCC 7 VO 6 VE 5 GND

HCPL-4200

300 mil DIP8

20 (1400)

1.6

1.0

1000

50

3750

CMOS compatible data input for HCPL-4200

37

Optoisolation and Optical Sensor Products

Isolated Voltage/Current Detector

Description
In the implementation of an interface from an electrically noisy environment into logic systems, it is often desirable to establish some current or voltage switching point or input switching threshold the HCPL3700 optocoupler provides such a solution. This device combines an AC or DC voltage and/or current detection function with high sensing input bu er ICs which permit control of threshold levels over a wide range like sensing industrial control systems, and ring detection in telephone system microprocessor interfacing. The HCPL-0370/3700/3760 threshold-sensing optocoupler can be used for sensing the AC/DC power on/o condition. At the optocoupler input, only a pair of series resistors RX/2 are required to limit the current. The AC signal can be ltered with a capacitor at either the input or the output of the optocoupler. The value of RX determines the threshold sensing voltage. HCPL-0370/3700/3760s low threshold current reduces power dissipation and its built-in diode bridge and hysteresis circuit reduces the number of external components used.

Applications
Limit switch sensing AC/DC voltage and current detector Relay contact monitor Relay coil voltage monitor User configurable voltage/current limit detection Microprocessor interfacing

Benets
Low threshold current reduces power dissipation Hysterisis circuit reduces external components and PCB size

Typical Block Diagram

V CC R X /2 1 AC 2 DC+ 3 DCR X /2 4 AC VO GND V CC 8 7 6 5 RL VOUT DC + INPUT 2 1 D1D2 ICC SCHEMATIC V CC 8

AC UP TO 1140 VPEAK

AC INPUT CONFIGURATION
V CC 1 AC R X /2 DC UP TO 1140 VPEAK R /2 X 2 DC+ 3 DC4 AC VO GND V CC 8 7 6 5 RL VOUT

AC INPUT D3D4 4 3 DC INPUT

IO V O 6 5 GND

DC INPUT CONFIGURATION

Isolated Voltage/Current Detector

Device Part No. Package Input Threshold Current mA Min. 1.96 0.87 1.96 1.96 0.87 Max. 3.11 1.56 3.11 3.11 1.56 Hysteresis mA typ 1.2 0.6 1.2 1.2 0.6 tPLH tPHL CMR - V/ s@VCM s s VCM Max. Max. CMR V/ s (Min.) V 40 40 40 40 40 15 15 15 15 15 600 600 600 600 600 140 140 140 140 140 VISO VRMS Min. 3750/5000# 3750/5000# 3750 3750 3750 VIORM VPEAK 1140* 1140* 567* 630* 630*

ACPL-K370-000E
AC 1 DC+ 2 DC- 3 AC 4 8 VCC V 7 NC V 6 VO 5 GND

NEW NEW

Stretched SO8 Stretched SO8 SO8 300 mil DIP8 300 mil DIP8

ACPL-K376-000E HCPL-0370 HCPL-3700 HCPL-3760

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000VRMS/1 minute Option 020, ^ - Advanced information, may subject to changes.

38

Optoisolation and Optical Sensor Products

High Linearity Analog Optocoupler

Description
Avago Technologies Analog Isolation Applications with Linear Optocouplers HCNR200/1 constitute the basic optical coupling building blocks for high linearity isolation applications. The HCNR200/1 comprises of a high performance LED and two closely matched photodiodes. The output photodiode produces a photo current that is linearly related to the light output of the LED. These high speed, low cost isolation ampli ers are highly suitable for the use in the feedback path of switched mode power supplies, motor speed and position measurement. Very high linearity and excellent low transfer gain variation are the advantages of using HCNR200/1. This circuit can be used in applications where high bandwidth, low-cost, and stable gain are required.

Benets
Simple and low cost Flexible design with the LED and both Photodiodes accessible to the designer Reinforced insulation

Applications
Industrial process control: Transducer isolator Isolator for thermocouples 4 mA to 20 mA loop isolation Low cost analog isolation Telecom: modem, PBX Switching power supply feedback loop and feedforward Monitor motor supply voltage Medical

Typical Block Diagram

V CC1 +5 V V CC2 +5 V 2 LED 1 Q2 2N3904 R4 10 8 PD2 6 5 1 LED ISOLATION BARRIER 2 K1 3 4 PD1 PD2 K2 6 5 NC 7 R2 68 k R5 10 k R7 470 Q4 2N3904 R6 10 HCNR200/1 NC 8

R3 10 k V IN R1 68 k 3 4 Q1 2N3906

V OUT

Q3 2N3906

PD1

High Linearity Analog Optocoupler Product Selection

Device Part No. Package Transfer Gain % Max. +/-15 +/-5 DC Non-Linearity % Max. 0.25 0.05 CTR % Min. 0.25 0.36 % Max. 0.75 0.72 VISO VRMS Min. 5000 5000 VIORM V peak 1414* 1414*

LED Cathode 1 LED Anode 2 PD1 Cathode 3 PD1 Anode 4

K1

LED K2

8 NC 7 NC 6 PD2 Cathode 5 PD2 Anode

HCNR200 HCNR201

400 mil DIP8 400 mil DIP8

PD1 PD2

-65 ppm/C gain temperature coefficient 1.5 MHz bandwidth

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 050

39

Optoisolation and Optical Sensor Products

Wideband Analog/Video Optocoupler

Description
The HCPL-4562 and HCNW 4562 are recommended for very high bandwidth (up to 15 MHz) AC analog designs such as coupling audio or video signals. HCPL-4562 provides simple and cost e ective solutions for coupling audio and video signals.

Benets
Optimized for video signal coupling Simple design for audio and video coupling Cost effective Reinforced insulation

Applications
Video isolation for the following standards/ formats: NTSC, PAL, SECAM, S-VHS, ANALOG RGB Low drive current feedback Element in switching power supplies: ISDN networks A/D converter signal isolation Analog signal ground isolation High voltage insulation

This circuit, with the HCPL-4562 wideband analog/video optocoupler, is optimized for video signal coupling. The peaked response of the detector circuit helps extend the frequency range over which the gain is relatively constant. The number of gain stages, the overall circuit topology, and the DC bias point are all chosen to maximize the bandwidth.

Typical Block Diagram

1 VCC 1 R1 6.8 K C1 IN 47 F R2 1.0 K 1N4150 D1 500 R4 = POTENTIOMETER +51 RESISTOR 51
2

8 7 6 5 VE R8 1.0 K R6 9.1 K Q2 Q3 R 11 470 R9 750 Q4

VCC 2

2 3 R3 100 Q1 4

OUT HIGH IMPEDANCE LOAD

R7 15 K R 10 100
2

GV = VOUT/VIN Q1 Q 4 = 2N3904

Wideband Analog/Video Optocoupler Product Selection

Device Part No. Package Bandwidth MHz typ 9 17 DC Non-Linearity % Max. 0.15 0.25 CTR % typ 52 45 IMRR dB typ 119 122 VISO VRMS Min. 5000 3750/5000# VIORM V peak 1414 630*

NC 1 ANODE 2 CATHODE 3 NC 4

8 VCC 7 VB 6 VO 5 GND

HCNW4562 HCPL-4562

400 mil DIP8 300 mil DIP8

0.3% / C gain temperature coefficient

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060 # - with UL 5000V RMS /1 minute Option 020

40

Optoisolation and Optical Sensor Products

General Purpose Phototransistor Optocoupler

Description
In switching power supply, Avago Technologies phototransistor optocouplers are the perferred choice for providing isolated feedback for the regulation loop. For this application, they do an excellent job of isolation, minimizing circuit complexity and reducing cost... For applications which require multiple isolated paths such as interfaces between logic circuits, the 2-channels and 4-channels phototransistors can be used.

Applications
Ground loop elimination Interface between logic circuits I/o or microprocessor interfacing Level shifting Regulation feedback circuits in smps

Typical Switching Power Supply Block Diagram

VIN Transformer Switch Control Circuit Error Amplifier & Comparator AC/DC Rectifier VOUT

Programmable Logic Controller I/O Units

I/O Module

General Purpose Phototransistor Optocoupler

Output

PLC/PC Controller

Logic Circuit

Input

41

Optoisolation and Optical Sensor Products

General Purpose Phototransistor Optocoupler DC Input Product Selection
Device Part No. Package Absolute Max. IF mA 50 50 CTR % Min. 50 50 50 20 100 40 63 100 160 50 50 50 50 % Max. 600 600 600 80 125 200 320 600 600 600 600 IF mA 5 5 5 10 10 10 10 10 10 5 5 5 5 VCE V 5 5 5 10 10 5 5 5 5 5 5 5 5 VCE(sat) V IF Max. mA 0.4 0.2 0.2 0.5 0.3 0.3 0.3 0.3 0.3 0.4 0.2 0.4 0.2 8 20 20 50 50 10 10 10 10 8 20 8 20 IC mA 2.4 1 1 2 2 2.5 2.5 2.5 2.5 2.4 1 2.4 1 tr/tf s typ 2/3 4/3 4/3 3/3 3/3 5/5 5/5 5/5 5/5 2/3 4/3 2/3 4/3 VISO BVCEO VF V VRMS V IF Min. Max. mA Min. 80 80 70 30 30 70 70 70 70 80 70 80 70 1.4 1.4 1.4 1.5 1.5 1.7 1.7 1.7 1.7 1.3 1.4 1.3 1.4 20 20 20 10 10 60 60 60 60 20 20 20 20 Note

Single Channel-4 pin

Anode 1 Cathode 2 4 Collector 3 Emitter

ACPL-217-500E (Half pitch) HCPL-181-000E# HCPL-817-000E*

SO4 SO4

3000 1 3750 1 5000 1/2/3 2500 1/2/3 3550 1/2/3 5000 1/2/3 5000 1/2/3 5000 1/2/3 5000 1/2/3 3000 1 5000 1/2/3 3000 1 5000 1/2/3

300 mil DIP4 50 300 mil DIP6 80 300 mil DIP6 60 300 mil DIP6 60 300 mil DIP6 60 300 mil DIP6 60 300 mil DIP6 60 SO8 50

Single Channel-6 pin

Anode 1 Cathode 2 3 6 Base 5 Collector 4 Emitter

4N25-000E 4N35-000E CNY17-1-000E CNY17-2-000E CNY17-3-000E CNY17-4-000E

Dual Channel-8 pin

8 7 6 5

ACPL-227-500E (Half pitch) ACPL-827-000E @

300 mil DIP8 50 SO16 300 mil DIP16 50 50

Pin 1, 3

Anode

Channel-16 pin Quad Pin 2, 4 Cathode ACPL-247-000E Pin 5, 7 Emitter (Half pitch) 16 15 14 13 12 11 10 9 Pin 6, 8 Collector

ACPL-847-000E
1 2 3 4 5 6 7 8

General Purpose Phototransistor Optocoupler AC Input

Device Part No. Package Absolute Max. IF mA +/-50 +/-50 +/-50 CTR % Min. 20 20 50 20 50 20 20 20 20 VCE % IF Max. mA V 400 400 150 300 150 400 300 400 300 5 1 1 1 1 1 1 1 1 5 5 5 5 5 5 5 5 5 VCE(sat) V IF Max. mA 0.4 0.2 0.2 0.2 0.2 0.4 0.2 0.4 0.2 8 20 20 20 20 8 20 8 20 IC mA 2.4 1 1 1 1 2.4 1 2.4 1 tr/tf s typ 2/3 4/3 4/3 4/3 4/3 2/3 4/3 2/3 4/3 BVCEO V Min. 80 35 35 35 35 80 70 80 70 VF V Max. 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 IF mA 20 20 20 20 20 20 20 20 20 VISO VRMS Min. Note

Pin 1, 3, 5, 7 Pin 2, 4, 6, 8 Pin 9,11,13,15 Pin 10,12,14,16

Anode Cathode Emitter Collector

Single Channel-4 pin

Anode Cathode 1 Anode Cathode 2 4 Collector 3 Emitter

ACPL-214-500E (Half pitch) HCPL-354-000E HCPL-354-00AE HCPL-814-000E HCPL-814-00AE

SO4 SO4 SO4

3000 1 3750 1 3750 1 5000 1/2/3 5000 1/2/3 3000 1 5000 1/2/3 3000 1 5000 1/2/3

300 mil DIP4 +/-50 300 mil DIP4 +/-50 SO8 +/-50

Dual Channel-8 pin

8 7
6 5

ACPL-224-500E (Half pitch) ACPL-824-000E

300 mil DIP8 +/-50 SO16 300 mil DIP16 +/-50 +/-50

Quad Channel-16 pin

16 15 14 13 12 11 10 9

ACPL-244-500E (Half pitch) ACPL-844-000E

Notes: 1 - IEC/EN/DIN EN 60747-5-2/5 Option 060 available, 2 - 0.4 Lead Spacing Option W00 available, 3 - Gull Wing SMD option available * CTR rank with Option 000E, 00AE, 00BE, 00CE, 00DE and 00LE available, # - CTR rank with option 000E, 00AE, 00BE, 00CE and 00DE available @ CTR rank with Option 000E, 00BE and 00CE available CTR rank with option 500E, 50AE, 50BE, 50CE and 50DE available, CTR rank with option 500E, 50BE, 50CE - CTR rank with option 500E and 50AE available.

42

Optoisolation and Optical Sensor Products

Solid State Relay (Photo MOSFET)

Description
Avago Technologies new ASSR Series are high-speed optically isolated MOSFEToutput solid-state relays that feature performance that has been quali ed over a wide industrial temperature range of -40C to +85C. They are Form A (normally open) single-pole single-throw relays in industry-standard 6-pin and 8-pin dual-inline (DIP) packages, and 4-pin small outline (SO) packages. Their output ratings range from 60V to 600V maximum load voltage and from 40mA to 2.5A continuous output current. Their transient immunity of more than 1kV/s and excellent noise rejection between input-output as well as between open terminals on the output will eliminate undesirable transient e ects. Reinforced insulation of 3.75kV with fast switching speed makes them suitable for a wide range of industrial, consumer and automotive applications. Compared to electromechanical relays, the ASSR Series o er distinct advantages, including the elimination of contact bounce, and problems due to shock, vibration, or mounting position. They have no wear out mechanism limiting the number of operations, and require no minimum contact wetting current. They are also free from magnetic elds, do not generate electrical noise, and are not sensitive to electromagnetic interference. Security Equipment Application Diagram

Benets
Superior to traditional electromechanical relays (EMR) Lower power consumption Faster switching speed with high transient immunity Smaller size Much better reliability High reinforced insulation in miniature SO-4 package Qualified performance over - 40C to +85C Expanding portfolio to address diversified market Low R(ON ) for less insertion loss Low C OFF) for better isolation performance High current capability with low R(ON)

Applications
Telecommunications switching Data communications Industrial control Medical system Security system Automatic test equipment Data acquisition system Measuring instruments EMR/reed relay replacement

General Purpose
The ASSR-14xx, ASSR-32xx and ASSR-41xx are designed for a wide variety of industrial and consumer electronics applications which includes telecommunications switching, data communications, automatic metering, medical system, security system, battery monitor, digital home appliances, set top boxes, etc.

Security Equipment Application Diagram

Sensor / Detector (Motion, Smoke, Light, etc.)

ASSR-1218

Sensor / Detector (Motion, Smoke, Light, etc.)

Controller / Processor

ASSR-xx20

Receiver / Alarm

Sensor / Detector Interface

Drive Circuit

43

Optoisolation and Optical Sensor Products

Low C(OFF) R(ON)

The ASSR-xxxC and ASSR-xxxR Series are speci cally designed for fast switching applications, commonly found in test and measurement applications such as pin electronics, data acquisition, multiplexers and matrix cards, and switching in the analog circuits of parametric measurement unit (PMUs). The low output capacitance, low on-resistance, and low output o -state leakage current of the ASSR Series provide higher system throughput and reduce system errors. In addition to their fast switching speeds, the ASSR Series provide reinforced insulation of 3.75kV, which is often required in industrial environments.

allow microprocessors to sense and control various loads. An AC output module allows logic-level voltages to control a switch that turns AC loads on and o . For example, the output module of a process controller might be used to control the motor starters of adjustable frequency drives, position valves, or dampers. As the computing speed increases, noise problems arise at the input interface as well as at the output interface. In addition, the use of small size relays result in more compact programmable controllers. Unlike electromechanical relays, the ASSR Series do not have mechanical contacts, which could eventually deteriorate from arcing or dust particles.

High Current
The ASSR-15x0, ASSR-1611 and ASSR-5211 are speci cally designed for high current applications, commonly found in the industrial applications. In programmable controllers, input and output modules

Standard
The ASSR-xxx8 and ASSR-xxx9 series are similar to competitive Photo MOSFET o erings with room temperature speci cations only to address applications in controlled environments such as telecommunications and security equipment.

Digital I/O Application Diagram

ASSR-xx20

Data Acquisition Multiplexer Application Diagram

Multiplexer Application Diagram
Multiplexer

Transducer A

Transducer B Output

Controller / Processor

Transducer C

Digital Logic Controller

ASSR-xx10

ASSR-x01C

Application Block Diagram

Input

Transducer N
Instrumentation Amplifier (Differential Input)

ACPL-214

ASSR-x02C

44

Optoisolation and Optical Sensor Products

Device
Opto-isolation

Part No.

Function

Package

Channel & Output Type 1 Form A 1 Form A 1 Form A 1 Form A 1 Form A 1 Form A 1 Form A 1 Form A

VISO kV Min. 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75 3.75

VO(OFF) V Min. 60 60 60 250 250 400 400 400 60 60 60 60 250 400 400 600 60 60 60 60 250 250 250 400 400 400

IO A Max. 0.2 0.6 1.0 0.05 0.2 0.04 0.12 0.1 0.2 0.6 1.0 2.5 0.2 0.12 0.1 0.2 0.2 0.6 1.0 1.0 0.05 0.2 0.2 0.04 0.12 0.1

IO(OFF) nA Max. 1000 100 100 10 100 10 100 1000 1000 100 100 100 100 100 1000 100 1000 100 100 100 10 1 100 10 100 1000

C(OFF) pF Max. 15 15 15 60 15

R(ON) Max. 10 1 0.5 50 10 100 25 35 10 1 0.5 0.1 10 25 35 16 10 1 0.5 0.5 50 8.5 10 100 25 35

TON ms Max. 5.0 0.5 1 0.5 1 0.5 0.5 3.0 5.0 0.5 1 3.0 1 0.5 3.0 3.0 5.0 0.5 1 1 0.5 0.5 1 0.5 0.5 3.0

TOFF ms Max. 5.0 0.2 0.2 0.2 0.2 0.2 0.2 1.0 5.0 0.2 0.2 0.5 0.2 0.2 1.0 0.5 5.0 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 1.0

ASSR-1218-003E
4

STD GP HC Low CxR GP Low CxR GP STD STD GP HC HC GP GP STD HC STD GP HC HC Low CxR Low CxR GP Low CxR GP STD

SO4 SO4 SO4 SO4 SO4 SO4 SO4 SO4

1 Turn -o Circuit

ASSR-1410-003E ASSR-1510-003E ASSR-301C-003E ASSR-3210-003E ASSR-401C-003E ASSR-4110-003E ASSR-4118-003E

Opto-isolation
1 6

ASSR-1219-001E ASSR-1411-001E ASSR-1511-001E ASSR-1611-001E ASSR-3211-001E ASSR-4111-001E ASSR-4119-001E ASSR-5211-001E

300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP6 1 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A SO8 2 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A 300mil DIP8 2 Form A

Turn -o Circuit

Opto-isolation 1
Turn-o Circuit

ASSR-1228-002E ASSR-1420-002E ASSR-1520-002E ASSR-1530-005E ASSR-302C-002E ASSR-322R-002E ASSR-3220-002E ASSR-402C-002E ASSR-4120-002E ASSR-4128-002E

3
Turn-o Circuit

Note: GP = General Purpose, Low CxR = Low C (OFF) x R (ON), HC = High Current, STD = Standard

Solid State Relay (Photovoltaic Driver)

Device Part No. Function Package Channel & Output Type 2 Form A VOC V Min. 6.5 ISC A Min. 15 VISO V Min. 3750

Opto-isolation 1
Turn-o Circuit

ASSR-V621-002E

GP

300mil DIP8

3
Turn-o Circuit

Opto-isolation 1
Turn-o Circuit

ASSR-V622-002E

GP

300mil DIP8

2 Form A

6.5

15

3750

3
Turn-o Circuit

45

Optoisolation and Optical Sensor Products

Powerline Communication Interface

Description
The HCPL-0810 / 8100 and ACPL-0820 are designed for narrow band powerline communication (PLC) analog front end interfacing applications. Compact in size, suitable for FCC Part 15 and EN50065-1 compliant design, this family can interface many common PLM transceivers to the powerline, thus simplifying the powerline modem (PLM) implementations.

Benets
Compact integrated solution Low power consumption Integrated safety features such as overtemperature shutdown Suitable for FCC Part 15 and EN50065-1 compliant design

Applications
Automatic meter reading (AMR) Powerline modem Home automation/control Security and surveillance General purpose isolated transceiver Internet appliances

Typical Power Line Modem Using ACPL-0820

5V R3

STATUS TXp TXn TX-EN PLM Transceiver Filter R1 Vin R2

1 2 3 4

Status In1 In2 Tx -en ACPL-0820

Vdd Out1 Out2 Gnd R4

8 7 6 5

5V Vout

Gain of Amp1 = - R3/R1,

Gain of Amp2 = - R4/R2,

R1=R2, R3=R4, Overall Di erential Output V out = (R3/R1) . V in

Power Line Communication Interface Product Selection

Part No. Package Signal Path Tx only Tx only Tx only Bandwidth GBWP MHz MHz Typ. Typ. 3.0 3.5 3.5 IO APP, Typ. 1.5 1.0 1.0 Harmonic Distortion dBc, Max. HD2 -60 -60 -60 HD3 -65 -65 -65 No No No Isolation VCC V Typ. 5 5 5 VISO VRMS Min. VIIORM V peak

ACPL-0820-000E HCPL-0810 HCPL-8100

SO8 SO8 300 mil DIP8

46

Optoisolation and Optical Sensor Products

Hermetic High Performance Optocouplers

Isolating one portion of an electrical circuit from another is the primary function of an optocoupler. These devices isolate di erent voltage levels between the input and output source. Avago Technologies optocouplers are ideally suited for isolating highly sensitive portions of a circuit from the e ects of transmitted common mode signals; o ering a variety of input and output characteristics that enable their use in high speed, high performance applications. Avago Technologies hermetic optocouplers excel in designs for harsh environments that require an exceptionally strong, rugged enclosure. For design ease, we o er most functions in 8and 16-Pin DIPs, 20 terminal LCCCs and 16-Pin Flat Packs with various lead con gurations for thru-hole or surface mount, with either single, dual or quad channels. These products are capable of operation and storage over the full military temperature range of -55C to +125C and can be purchased as either commercial product or with full MIL-PRF-38534 Class Level H or K testing. In line with regulations and our customers needs, we do not o er unleaded solder on our solder dipped devices. All devices are manufactured and tested on a MILPRF-38534 certi ed line and are included in the DLA (Defense Logistics Agency) Quali ed Products Database Supplemental Information Sheets QPDSIS-38534 as Hybrid Microcircuits. Avago Technologies has supplied high reliability hermetic optocoupler products since 1975 for use in state-of-the-art applications. To meet the requirements of high reliability, products must be designed with rugged capabilities. They must be able to withstand severe levels of environmental stress and exposure without failure over extended periods of time. We have accomplished this objective in designing optocouplers that have proven their merits in numerous advanced space and defense programs in the international marketplace. Avago Technologies continuity and support of the industry has remained stable, with zero product obsolescence. We are committed to continued process and performance upgrades, backed up with diligent noti cation to our customers of any changes made. If use in radiation environments is a concern, the shallow depth and small junctions featured in Avago Technologies IC process provides high radiation immunity. Although the devices are not manufactured as Rad-Hard, they have proven tolerant to radiation e ects, which is substantiated by available data. Statistical Process Control and extensive reliability monitoring (life testing of hundreds of thousands of hours) are standard processes for hermetic optocouplers. Control charts are utilized at each critical step of the process and reviewed by product engineering to assure expected quality and reliability. Avago Technologies is a champion of DLAs QPDSIS and SMD (Standard Microcircuit Drawing) programs. We support standardization, which results in cost-e ectiveness and a streamlined acquisition process. As such Avago Technologies o ers all Class H and Class K products under SMD numbers. Each Hi-Rel device is dual marked with the DLA SMD and Avago Technologies part numbers. Our Screening and Quality Conformance Inspection is outlined on the following page. Custom programs may include full Group A, B, C, and D inspection if required.

Benets
Long term commitment zero obsolescence Recognized for high quality, reliability, and customer support Certified and qualified to classes H and K of MIL-PRF-38534 -55C to +125C operating temperature range All products available on DLA SMDs General purpose and application speci c products available

Applications
Military, aerospace and harsh industrial applications such as: Switching power supplies/UPS Motor control Field bus Inverters Power distribution Communications

47

Optoisolation and Optical Sensor Products

Screening per MIL-PRF-38534

Procedure Nondestruct bond pull Internal visual Temperature cycle Constant acceleration Visual inspection PIND* Serialization Pre-Burn-In Elec. Test Burn-In Interim Elec. Test Post Burn-In Elec. Test Final Elec. Test Method 2023 2017 1010 2001 2020 Conditions Class H N/A 100% 100% 100% 100% N/A N/A 100% 100% N/A 100% 100% 100% 100% 100% 100% 100% 100% N/A 100% Class K 100% 100% 100% 100% 100% N/A* 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

Condition C, -65C to +125C, 10 cycles 3Kgs, Y1 and Y2 Internal requirements Condition A Group A, subgroup 1 (except II-O) (DC @ +25C) Condition B, +125C, 160 hours Condition B, +125C, 320 hours Group A, subgroup 1 (except II-O) (DC @ +25C) Group A, subgroup 1, (DC @ +25C), 10% PDA Group A, subgroup 1, (DC @ +25C), 2% PDA Group A, subgroup 2 (DC @ +125C) Group A, subgroup 3 (DC @ -55C) Group A, subgroup 9 (AC @ +25C) Group A, subgroup 10 (AC @ +125C) Group A, subgroup 11 (AC @ -55C) Condition A Condition A

1015

Fine Leak Gross Leak Radiographics External visual

1014 1014 2012 2009

* PIND and RGA (Internal Water Vapor Content) testing (Group C) is no longer required on Avago Technologies optocouplers due to the construction of the devices. DLA approved this test elimination in 2002.

Quality Conformance Inspection

Group A Testing
Group A testing is satis ed per the in-line veri cation testing requirements of MIL-PRF-38534 for Class H devices utilizing Option 1. Group A testing is performed per end of line sample testing requirements of MIL-PRF-38534 for Class K devices utilizing Option 2.

Group B Testing
Group B testing is satis ed by performing in-line process monitors as required by MIL-PRF-38534 for Class H devices utilizing Option 1. Group B testing is satis ed by performing end of line sampling as required by MIL-PRF-38534 for Class K devices utilizing Option 2.

Group D Testing
Group D testing is not performed. Note that Group D requirements are satis ed during incoming inspection element evaluation. Please be advised that Class H and Class K devices have very similar Screening and Quality Conformance Inspection requirements as shown above. Class K devices, however, have substantially more stringent element evaluation and assembly criteria. The quality and reliability of a Class K device must be built in, not tested out.

Group C Testing
Group C testing is performed only on the rst inspection lot and as required to evaluate or qualify changes per the requirements of MIL-PRF-38534.

48

Optoisolation and Optical Sensor Products

Hermetically Sealed High Speed Logic Gate Optocouplers

Single Channel Schematic Commercial Class H Part Number HCPL-5200 HCPL-5230 HCPL-6230 HCPL-6250 HCPL-5400 HCPL-5430 HCPL-6430 6N134 HCPL-5600 HCPL-5630 HCPL-5650 HCPL-6630 HCPL-6650 ACPL-2670L ACPL-5600L ACPL-5630L HCPL-1930 HCPL-5201 HCPL-5231 HCPL-6231 HCPL-6251 HCPL-5401 HCPL-5431 HCPL-6431 6N134/883B HCPL-5601 HCPL-5631 HCPL-5651 HCPL-6631 HCPL-6651 ACPL-2672L ACPL-5601L ACPL-5631L HCPL-1931 DLA SMD Class H * 5962-8876801 5962-8876901 5962-8876902 5962-8876903 5962-8957001 5962-8957101 5962-8957102 8102801 5962-9085501H 8102802 8102805 8102803 8102804 5962-0824203H 5962-0824201H 5962-0824202H 5962-8957201 Class K DLA SMD Class K * 5962-8876802K 5962-8876904K 5962-8876905K 5962-8876906K 5962-8957002K 5962-8957103K 5962-8957104K 5962-9800101K 5962-9085501K 5962-9800102K 5962-9800103K 5962-9800104K 5962-0824203K 5962-0824201K 5962-0824202K 5962-8957202K Package 8 16 16 20 pin pin pin pad DIP DIP FP LCCC No. of Typical Common Chan- Data Mode @ nels Rate VCM=50V 1 2 2 4 1 2 2 2 1 2 2 2 4 2 1 2 2 5MBd 5MBd 5MBd 5MBd 1000V/s 1000V/s 1000V/s 1000V/s Input Current Withstand Test Voltage 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc Supply Voltage

Vcc Anode Cathode Vo Ve Ground

HCPL-520K HCPL-523K HCPL-623K HCPL-625K HCPL-540K HCPL-543K HCPL-643K HCPL-268K HCPL-560K HCPL-563K HCPL-663K HCPL-665K ACPL-268KL ACPL-560KL ACPL-563KL HCPL-193K

2-8 mA 2-8 mA 2-8 mA 2-8 mA 6-10 mA 6-10 mA 6-10 mA 10-20 mA 10-20 mA 10-20 mA 10-20 mA 10-20 mA 10-20 mA 10-20 mA 10-20 mA 10-20 mA

20V 20V 20V 20V

Vcc Anode Cathode Ve Vo Ground

20MBd 500V/s 20MBd 500V/s 20MBd 500V/s 10MBd 10MBd 10MBd 10MBd 10MBd 10MBd 10MBd 10MBd 10MBd 1000V/s 1000V/s 1000V/s 1000V/s 1000V/s 1000V/s 1000V/s 1000V/s 1000V/s

1500 Vdc 5.25V 1500 Vdc 5.25V 1500 Vdc 5.25V 1500 Vdc 1500 Vdc 1500 Vdc 2500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 3.3V 3.3V 3.3V

Vcc Anode Cathode Ve Vout Ground

Vcc Anode Cathode Vo Ve Ground

Vcc Anode Cathode +li Base 1 +li Base 2

Ve Vo
Ve1 Ground Vcc

10MBd 1000V/s 12.5-60 mA 1500 Vdc 5.5V

Vo1 Ve2 Vo2 Ground

Vcc Anode Ve *DLA SMD number does not include extensions for lead form and finish Cathode Vout Ground

Hermetically Sealed High Speed Transistor Optocouplers

Base 1 Single +li Channel Schematic +li Vcc Ve1 Vo1 Ve2 Vo2 Ground

Commercial Class H Part Number 4N55 HCPL-5500 HCPL-5530 HCPL-6530 HCPL-6550 4N55/883B HCPL-5501 HCPL-5531 HCPL-6531 HCPL-6551

DLA SMD Class H * 5962-8767901 5962-9085401H 5962-8767902 5962-8767903 5962-8767904

Class K

DLA SMD Class K * 5962-8767905K 5962-9085401K 5962-8767906K 5962-8767907K 5962-8767908K

Base 2

Package No. of Typical Current Chan- Data Transfer 8 16 16 20 nels Rate Ratio pin pin pin pad DIP DIP FP LCCC 2 1 2 2 4 700 KBd 700 KBd 700 KBd 700 KBd 700 KBd 9% min 9% min 9% min 9% min 9% min

Input Current

Withstand Test Voltage 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc

Supply Voltage

Vcc Anode Cathode Vb Vout Ground

HCPL-257K HCPL-550K HCPL-553K HCPL-653K HCPL-655K

12-20 mA 12-20 mA 12-20 mA 12-20 mA 12-20 mA

18V 18V 18V 18V 18V

Vcc *DLA SMD number does not include extensions for lead form and finish Anode Cathode Vout Ground

dc+ Input 2 1 ac Input 4 dc- Input 3

D1

D2

Icc Io

Vcc 8 Vo 6 Ground 5

D3

D4

Vdd1 Vin+ VinGround 1

Vdd2 Vout+ VoutGround 2

Io + If + Vf -

Vcc Anode Cathode Ground

49

N/C

8 VCC

Cathode

Vo Ground

Optoisolation and Optical Sensor Products

Anode Ve Cathode Vout Ground +li Base 1 +li Base 2
Anode

Vcc

Hermetically Sealed High Gain Optocouplers

Vo Cathode Ve Ground

Vcc Ve1 Vo1 Ve2 Vo2 Vcc Ground

Single Anode Channel Cathode Anode Schematic

Cathode

Vcc Vb
Vcc Vout Ve Ground Vo Ground

Commercial Class H Part Number 6N140A HCPL-5700 HCPL-5730 HCPL-6730 HCPL-6750 ACPL-1770L ACPL-5700L ACPL-5730L 6N140A/883B HCPL-5701 HCPL-5731 HCPL-6731 HCPL-6751 ACPL-1772L ACPL-5701L ACPL-5731L

DLA SMD Class H * 8302401 5962-8981001 5962-8978501 5962-8978502 8302401 5962-0822703H 5962-0822701H 5962-0822702H

Class K

DLA SMD Class K * 5962-9800201K 5962-8981002K 5962-8978503K 5962-8978504K 5962-9800201K 5962-0822703K 5962-0822701K 5962-0822702K

Package 8 16 16 pin pin pin DIP DIP FP

No. of Typical Current Chan- Data Transfer 20 nels Rate Ratio pad LCCC 4 1 2 2 4 4 1 2 100 KBd 100 KBd 100 KBd 100 KBd 100 KBd 100 KBd 100 KBd 100 KBd 300% min 300% min 300% min 300% min 300% min 300% min 300% min 300% min

Input Current

Withstand Test Voltage 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc

Supply Voltage Range 18V 18V 18V 18V 18V 3.3V 3.3V 3.3V

Anode Anode Cathode Cathode

Anode Cathode

Vcc Ve

Vcc

Vout Vout Vcc Ground VoGround

Ve Ground

dc+ Input +li

2 Base 1 D1

D2

Vcc Vcc Ve1 8 Icc Vo1

1 Anode +li ac Input D3 Cathode 4 Base 2 dc- Input 3

D4

Vcc Ve2 Ve Vo2 Io Vo 6 Vo Ground

Ground Ground

HCPL-177K HCPL-570K HCPL-573K HCPL-673K HCPL-675K ACPL-177KL ACPL-570KL ACPL-573KL

0.5-5 mA 0.5-5 mA 0.5-5 mA 0.5-5 mA 0.5-5 mA 0.5-5 mA 0.5-5 mA 0.5-5 mA

Vcc *DLA SMD number does not include extensions for lead form and finish Anode Vdd1 Anode Vin+ Cathode Cathode Vb Vdd2 Vcc Vout Ve Vout+ Ground Vout VoutGround

Vin-

Hermetically Sealed AC/DC to Logic Interface Optocouplers

Ground 1 Ground 2
Anode +li Cathode Base 1 +li

Base 2

Single Channel If + Vf Schematic

D1 D2

Vcc Vcc Io Ve1 + Vout Vo1 Ground Ve2 Vo2 Ground

dc+ Input 2 1 Anode ac Input Cathode Anode 4 dc- Input Cathode 3

Vcc Icc 8 Vcc Vb Vo IoVcc 6 Vout Ground Ground 5

Commercial Class H Part Number HCPL-5760 HCPL-5761

DLA Class K DLA SMD SMD Class H * Class K * 5962-8947701 HCPL-576K 5962-8947702K

8 pin DIP

No. of Channels 1

Typical Data Rate 100 KHz

Input Threshold Current 2.5 mA TH+

Output Current 2.6 mA

Withstand Test Voltage 1500 Vdc

D3

D4

Ground
Vdd1 Vdd2 *DLA SMD number does not include extensions for lead form and finish Vin+ VinAnode Ground 1 Cathode 1
ANODE 2

Vout+ Vcc VoutN/C

Ground 2 VoutCC 8 V Ground

7 N/C 6 VO

Hermetically Sealed Power MOSFET

CATHODE 3

Io +

dc+ Input Vf 2

Single 1 Channel ac Input 4 Schematic dc- Input

D1 D2 D3 D4

N/C + 4 If

SHIELD

5 VEE

Vcc Icc 8 Io Vo 6 Ground Vcc 5

Commercial Part Number HSSR-7110

Class H

DLA Class E SMD Class H *

DLA SMD Class E *

Package 8 pin DIP

No. Output of Withstand Channels Voltage 1 1 90 V 90 V

Output OnResistance 1.0 Ohm 1.0 Ohm

Maximum Maximum Input Load O-State Current Current Leakage 0.8 A ac 1.6 A dc 0.8 A ac 1.6 A dc 10 A 10 A

Input/ Output Insulation

Anode Cathode Vdd1 Vin+ VinGround 1 Vdd2 Ground Vout+ VoutGround 2

HSSR7111 HSSR7112

5962HSSR-711E 59629314001H 9314001E 59629314002H

10-20mA 1500 Vdc 5-20mA 1500 Vdc

1 ANODE 2

N/C

8 VCC 7 N/C 6 VO

*DLA SMD number does +not include extensions for lead form and finish Io
CATHODE 3 If +

Vf - N/C 4

SHIELD

5 VEE

Vcc Anode Cathode Ground

1 ANODE 2 CATHODE 3 N/C 4

N/C

8 VCC 7 N/C 6 VO

SHIELD

5 VEE

50

Anode Anode Cathode Cathode Anode Cathode

Vo Vout Ground Ve Ground Ground

Vcc Vcc Vb Vcc Ve Vout

Optoisolation and Optical Sensor Products

+li Anode Anode Base 1 Cathode Cathode +li Base 2 Vcc Vcc Vcc Ve1 Ve Vo1 Vout Vo Ve2 Vo2 Ground Ground Ground dc+ Input 2 D1 Anode Anode 1 Cathode Cathode ac Input D3 4 dc- Input 3
D2

Icc

D4

Hermetically Sealed Analog Isolation Amplier

Vdd1 +li Vin+ Base 1 Anode VinCathode Ground 1 +li Base 2

Vcc Vcc Vcc 8 Vb Ve Vo Io Vout Vout 6 Ground Ground Ground 5

Single Channel Schematic

Vdd2 Vcc Vcc Vout+ Ve1 Vo1 VoutVe2 Vout Ground 2 Vo2 Ground Ground

Commercial Part Number HCPL-7850

Class H

DLA SMD Class H *

Class E

DLA SMD Class E * 59629755701E

Package 8 pin DIP

No. Gain of Tolerance Channels (Max. %) 1 5

NonLinearity (Max. %) 0.1

Prop Delay s (Max.) 11

CMR V/s (Min.) 5000

Bandwidth Oset Khz mV (typ.) (typ.) 100 0.6

HCPL-7851 5962-9755701H ACPL-785E

dc+ Input If + 2 Anode Vf - D1 Cathode 1 ac Input 4 dc- Input 3

D3

D2

Io + Vcc Vcc Icc Vb 8 Io Vout Vo 6 Ground Ground 5

D4

Vcc *DLA SMD number does not include extensions for lead form and finish Anode Vdd1 Cathode Vin+ Anode VinCathode Ground 1 Vdd2 Vcc Vout+ Ground VoutVout Ground 2 Ground

Hermetically Sealed Intelligent Power Module and Gate Drive Interface

dc+ Input 2 ANODE 2 If + D1
CATHODE 3

dc- Input 3

Single Channel 1 Vf ac Input Schematic 4

D2

N/C

8 VCC

Icc Io

Vcc 7 N/C 8
6 VO

Io +

N/C D34

D4

SHIELD

5 VEE6

Vo

Commercial Class H Part Number HCPL-5300 HCPL-5301

DLA SMD Class H *

Class K

DLA SMD Class K * 5962-9685201K

Package 8 pin DIP

No. Typical of Data Channels Rate 1 2MBd

Current Transfer Ratio

Input Current

Common Mode @ VCM=1000V

Withstand Test Voltage 1500 Vdc

Ground 5 Vcc

5962-9685201H HCPL-530K

30 % Min. 10-20 mA 10kV/s

Vdd1 Anode Vin+ Cathode VinGround 1

Vdd2 Vout+ VoutGround Ground 2

*DLA SMD number does not include extensions for lead form and finish
1 ANODE 2 If + N/C 8 VCC Io + 7 N/C 6 VO SHIELD 5 VEE

Vf CATHODE 3
N/C 4

Hermetically Sealed Output Current IGBT Gate Drive

Vcc Anode Single Cathode Channel Schematic Ground

Commercial Class H Part Number HCPL-5120 HCPL-5121 HCPL-5151

DLA SMD Class H * 5962-0420401H 5962-0420501H

Class K

DLA SMD Class K *

Package 8 pin DIP

No. of Channels 1 1

Peak Output Current 2.0 A 0.5 A

UVLO+

UVLO-

Input Common Current Mode @ VCM=1000V 10-18 mA 10-18 mA 10kV/s 10kVs

Withstand Test Voltage 1500 Vdc 1500 Vdc

1 ANODE 2 CATHODE 3 N/C 4

N/C

8 VCC 7 N/C 6 VO

13.5V Max. 13.5V Max.

9.5V Min. 9.5V Min.

SHIELD

5 VEE

HCPL-5150

*DLA SMD number does not include extensions for lead form and finish

51

Optoisolation and Optical Sensor Products

Optocoupler Package Dimensions

ACPL-Cxxx, ACPL-Kxxx
Stretched SO8 8mm Clearance 8mm Creepage
5.850 0.50 (0.230 0.010)

ACPL-Wxxx

Stretched SO6 8mm Clearance 8mm Creepage

4.580 0.254 (0.180 0.010)

RECOMMENDED LAND PATTERN

12.650 (0.5) 3 6.807 0.127 (0.268 0.005) 1.905 (0.1) 2 1

12.65 (0.498)

6.807 0.127 (0.268 0.005)

1.91 (0.075) 0.76 (0.030) 1.590 0.127 (0.063 0.005)

8 1.590 0.127 (0.063 0.005) 7 3.180 0.127 (0.125 0.005) 0.750 0.250 (0.0295 0.010) 0.200 0.100 (0.008 0.004) 0.381 0.130 (0.015 0.005) 1.270 (0.050) BSG 0.450 (0.018) 4 5 6

7 3.180 0.127 (0.125 0.005) 0.450 (0.018)

45

45

0.381 0.130 (0.015 0.005) 1.270 (0.050) BSG

11.50 0.250 (0.453 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). LEAD COPLANARITY = 0.1 MM (0.004 INCHES).

0.750 0.250 (0.0295 0.010) 11.50 0.250 (0.453 0.010)

0.200 0.100 (0.008 0.004)

DIMENSIONS IN MILLIMETERS AND (INCHES). LEAD COPLANARITY = 0.1 MM (0.004 INCHES).

ACPL-Hxxx

Stretched SO8 7mm Clearance 8mm Creepage

5.850 0.50 (0.230 0.010) 10.7 (.421)

ACPL-Pxxx

Stretched SO6 7mm Clearance 8mm Creepage

4.580 0.254 (0.180 0.010) 10.7 (.421)

3 6.807 0.127 (0.268 0.005) 2.16 (.083)

6.807 0.127 (0.268 0.005) 7.620 (0.300) 45 1.590 0.127 (0.063 0.005) 7 3.180 0.127 (0.125 0.005) 1.000 0.040 (0.0295 0.010) 0.200 0.100 (0.008 0.004) 0.381 0.127 (0.015 0.005) 1.270 (0.050) BSG 0.450 (0.018)

2.16 (.085)

7.620 (0.300) 45

7 3.180 0.127 (0.125 0.005) 0.450 (0.018)

0.381 0.130 (0.015 0.005) 1.270 (0.050) BSG

9.700 0.250 (0.382 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). LEAD COPLANARITY = 0.1 MM (0.004 INCHES).

1.000 0.040 (0.0295 0.010) 9.700 0.250 (0.382 0.010)

0.200 0.100 (0.008 0.004)

DIMENSIONS IN MILLIMETERS AND INCHES. LEAD COPLANARITY = 0.1 MM (0.004 INCHES).

52

Optoisolation and Optical Sensor Products

Optocoupler Package Dimensions

300 mil 6 pin DIP
TYPE NUMBER
6 5 4 7.62 0.3 (0.3)

OPTION CODE

A 4N45 V
PIN ONE DOT DATE CODE
1

6.5 0.5 (0.256)

YYWW
2 7.3 0.5 (0.287) 3.5 0.5 (0.138) 3 0.35 0.15/-0.10 (0.14) 7.62 ~ 9.98

Options Available
020 = UL 5000 Vrms /1 Minute Option 060 = IEC/EN/DIN EN 60747-5-2/5 Approved Part Option 300 = Gull Wing Surface Mount Option 500 = Tape & Reel Packaging Option xxxE = Lead Free Option
Remarks: The notation # is used for existing products, while (new) products launched since 15th July 01 will use -

2.8 0.5 (0.110)

3.3 0.5 (0.13) 0.5 0.1 (0.02)

0.5 (0.02) TYP

2.54 0.25 (0.1)

DIMENSIONS IN MILLIMETERS AND (INCHES)

300 mil 8 pin DIP

9.65 0.25 (0.380 0.010) TYPE NUMBER 8 7 A XXXXZ YYWW RU 1 1.19 (0.047) MAX. 2 3 4 UL RECOGNITION 6 5 OPTION CODE* DATE CODE 7.62 0.25 (0.300 0.010) 6.35 0.25 (0.250 0.010)

300 mil 8 pin DIP Gullwing Option 300 SMD

LAND PATTERN RECOMMENDATION 9.65 0.25 (0.380 0.010)
8 7 6 5

1.016 (0.040)

6.350 0.25 (0.250 0.010)

10.9 (0.430)

1.78 (0.070) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002)

1.27 (0.050) 1.780 (0.070) MAX. 9.65 0.25 (0.380 0.010) 7.62 0.25 (0.300 0.010)

2.0 (0.080)

5 TYP. 3.56 0.13 (0.140 0.005) 4.70 (0.185) MAX.

1.19 (0.047) MAX.

0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). * MARKING CODE LETTER FOR OPTION NUMBERS "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
1.080 0.320 (0.043 0.013)

3.56 0.13 (0.140 0.005)

+ 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002)

1.080 0.320 (0.043 0.013)

0.65 (0.025) MAX. 2.54 0.25 (0.100 0.010)

0.635 0.25 (0.025 0.010) 0.635 0.130 2.54 (0.025 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

12 NOM.

53

Optoisolation and Optical Sensor Products

Optocoupler Package Dimensions

300 mil 8 pin DIP (white)
9.80 0.25 (0.386 0.010) TYPE NUMBER 8 7 6 XXXXZ YYWW 1 1.19 (0.047) MAX. 2 3 RU 4 UL RECOGNITION
1 2 3 4

300 mil 8 pin DIP (white) Gullwing Option 300 SMD

7.62 0.25 (0.300 0.010)
9.80 0.25 (0.380 0.010)
8 7 6 5

PAD LOCATION (FOR REFERENCE ONLY) 1.016 (0.040)

OPTION CODE DATE CODE

6.35 0.25 (0.250 0.010)

6.350 0.25 (0.250 0.010)

TYP.

10.9 (0.430)

1.78 (0.070) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002)

1.19 (0.047) MAX. 1.780 (0.070) MAX. 1.27 (0.050) 9.65 0.25 (0.380 0.010) 3.56 0.130 (0.140 0.005) 7.62 0.25 (0.300 0.010) 2.0 (0.080)

5 TYP.

4.70 (0.185) MAX.

0.51 (0.020) MIN. 2.92 (0.115) MIN.

DIMENSIONS IN MILLIMETERS AND (INCHES). "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED.
1.080 0.320 (0.043 0.013) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.635 0.25 (0.025 0.010) 0.635 0.130 (0.025 0.005)

0.20 (0.080) 0.33 (0.013)

1.080 0.320 (0.043 0.013)

0.65 (0.025) MAX. 2.54 0.25 (0.100 0.010)

12 NOM.

400 mil 8 pin DIP

11.15 0.15 (0.442 0.006) 8 7 6 5 11.00 MAX. (0.433)

400 mil 8 pin DIP Gull Wing Option 300 SMD

11.15 0.15 (0.442 0.006) 8 7 6 5 PAD LOCATION (FOR REFERENCE ONLY) 6.15 (0.242) TYP. 9.00 0.15 (0.354 0.006) 12.30 0.30 (0.484 0.012)

TYPE NUMBER DATE CODE

9.00 0.15 (0.354 0.006)

HCNWXXXX YYWW 1 2 3 4 1.55 (0.061) MAX.

1 10.16 (0.400) TYP. 7 TYP. 5.10 MAX. (0.201) + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 1.78 0.15 (0.070 0.006)

4 1.55 (0.061) MAX. 1.3 (0.051) 12.30 0.30 (0.484 0.012) 11.00 MAX. (0.433)

0.9 (0.035)

4.00 MAX. (0.158)

3.10 (0.122) 3.90 (0.154) 2.54 (0.100) TYP. 1.78 0.15 (0.070 0.006) 0.40 (0.016) 0.56 (0.022)

0.51 (0.021) MIN.

2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

0.75 0.25 (0.030 0.010)

1.00 0.15 (0.039 0.006)

+ 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 7 NOM.

54

Optoisolation and Optical Sensor Products

Optocoupler Package Dimensions

SO5 SMD
PAD LOCATION (FOR REFERENCE ONLY) 4.4 (0.17) 0.102 0.102 (0.004 0.004) 0.15 0.025 (0.006 0.001) 1.27 BSG (0.050) 0.71 MIN. (0.028) 0.4 0.05 (0.016 0.002) DIMENSIONS IN MILLIMETERS (INCHES) 0.9 (0.04) 0.5 (0.02) 2.5 (0.10) 0.3 (0.01) 3.6 0.1 (0.142 0.004) MXXX 4.4 0.1 (0.173 0.004) XXX ANODE 1 6 2.5 0.1 (0.098 0.004)

7.0 0.2 (0.276 0.008)

CC

1. 3 (0.05)

5 OUT 4 GND

CATHODE 3

7.2 (0.28) DIMENSIONS IN MILLIMETERS (INCHES)

SO8 SMD
LAND PATTERN RECOMMENDATION

SO8 SMD (ACSL-6210,ACPL-0820 & HCPL-0810)

LAND PATTERN RECOMMENDATION

6 XXX YWW

5.994 0.203 (0.236 0.008)

0.189 (4.80) 0.197 (5.00) 7.49 (0.295)

Thermal Pad

3.937 0.127 (0.155 0.005) 1 2

TYPE NUMBER (LAST 3 DIGITS) DATE CODE

4 1.270 BSG (0.050) 0.64 (0.025)

8 0.228 (5.80) 0.244 (6.20)

5 0.150 (3.80) 0.157 (4.00)

7.49 (0.295)

PIN ONE
0.406 0.076 (0.016 0.003)

1.9 (0.075)

1.9 (0.075) 0.64 (0.025)

1 7 45 X 0.432 (0.017) 0.013 (0.33) 0.020 (0.51)

* 5.080 0.127 (0.200 0.005) 3.175 0.127 (0.125 0.005)

1.524 (0.060)

0 ~ 7

0.228 0.025 (0.009 0.001)

0.054 (1.37) 0.069 (1.75) 0.040 (1.016) 0.060 (1.524) DIMENSIONS: INCHES (MILLIMETERS)

0.004 (0.10) 0.010 (0.25)

0.010 (0.25) 0.020 (0.50) x 45

0.008 (0.19) 0.010 (0.25)

*TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 0.254 (0.205 0.010) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.

0.203 0.102 (0.008 0.004) 0.305 MIN. (0.012)

0.016 (0.40) 0.050 (1.27) MIN MAX

0 8

SO16 SMD (Include ACML series Digital Isolator)

0.018 (0.457) 16 15 14 13 12 11 10 9 TYPE NUMBER DA DATE CODE 316J YYWW 0.295 0.010 (7.493 0.254) 0.345 0.010 (8.986 0.254) ALL LEADS TO BE COPLANAR 0.002 0.050 (1.270)

SO16 SMD (ACSL-6300/6310/6400/6410/6420)

0.386 (9.802) 0.394 (9.999)
8 1

0.228 (5.791) 0.244 (6.197)

0.152 (3.861) 0.157 (3.988)

08 0.025 MIN. 0.408 0.010 (10.160 0.254)

0.008 0.003 (0.203 0.076) ST STANDOFF

0.013 (0.330) 0.020 (0.508) 0.054 (1.372) 0.068 (1.727) 0.008 (0.191) 0.010 (0.249) 0.010 (0.245) 0.020 (0.508)
x 45

0.406 0.10 (10.312 0.254) 9

LAND PATTERN RECOMMENDATION

0.050 (1.270) 0.060 (1.524) 0.040 (1.016) 0.060 (1.524) 0.004 (0.102) 0.010 (0.249)

0 8 TYP

0.016 (0.406) 0.050 (1.270)

0.018 (0.457)

0.138 0.005 (3.505 0.127)

0.458 (11.63)

DIMENSIONS: INCHES (MILIMETERS)

MIN MAX

0.085 (2.16) 0.025 (0.64)

55

Optoisolation and Optical Sensor Products

PAD LOCATION (for reference only)

Digital Isolator Package Dimensions (Exclude ACML series)

8 7 6 5
8

0.370 (9.400) 0.390 (9.900)

7 6 5

0.040 (1.016) 0.047 (1.194) 0.190 TYP. (4.826) 0.370 (9.398)

300 mil 8 pin DIP

1

0.240 (6.096) 0.260 (6.604)

PAD 300 mil 8 pin Gull(9.400) Option 300 SMD LOCATION (for reference only)0.390 (9.906) Wing 0.040 (1.016) 0.370
1 2 3 4

0.240 (6.100) 0.260 (6.600)

6 5

0.390 (9.900)
7 6

0.370 (9.398) 0.400 (10.160) 7 6

0.370 (9.400) 0.390 (9.900)

7 6

0.047 (1.194) PAD LOCATION (for reference only) 0.047 (1.194) 0.040 (1.016) 0.070 (1.778) 0.047 (1.194)
0.370 (9.400) 0.390 (9.900) 0.290 (7.370) 0.310 (7.870)

0.240 (6.096) 0.260 (6.604) 0.240 (6.096) 0.120 (3.048) 0.260 (6.604) 0.150 (3.810)

0.290 (7.366) 0.310 (7.874)

0.55 (1.397) 0.65 (1.651) 0.030 (0.762) 0.045 (1.143)

0.240 (6.100) 5 0.045 (1.143) 0.260 (6.600) 0.065 (1.651)

3 4 0.240 (6.100)

0.015 (0.381) 0.025 (0.635) 0.190 TYP. (4.826)

0.190 TYP. (4.826)

0.370 (9.398) 0.390 (9.906)

1 1 2

0.260 (6.600)

0.370 (9.398) 3 4 0.400 (10.160)

0.008 (0.203) 0.015 (0.381) 0.015 (0.381) 0.035 (0.889) 0.090 (2.286) 0.110 (2.794) 0.120 (3.048) 0.150 (3.810)

0.120 (3.048) 0.150 (3.810) 4

0.047 (1.194) 0.070 (1.778)

0.370 0.008 (0.203) (9.398) 0.390 (0.381) 0.015 0.013 (0.330) (9.906) 0.025 (0.635) 0.015 (0.381) 0.025 (0.635)

0.030 (0.762) 0.045 (1.143) 0.015 (0.380) 0.023 (0.584)

0.370 (9.398) 0.400 (10.160)

0.290 (7.366) 0.310 (7.874)

0.300 (7.620) 0.290 (7.366) 0.370 (9.398) 0.310 (7.874)

3 8

0.55 (1.397) 0.65 (1.651) 0.55 (1.397) 0.65 (1.651) 0.008 (0.203) 0.015 (0.381)

0.030 (0.760) 0.056 (1.400)

0.120 (3.048) 0.150 (3.810) 0.015 (0.381) MIN 0.035 (0.889) DIMENSIONS: INCHES (MILLIMETERS) MAX 0.015 (0.381) 0.030 (0.762) 0.090 (2.286) 0.035 (0.889) 0.045 (1.143) 0.110 (2.794) 0.015 (0.380) 0.030 (0.762) (0.584) 0.090 (2.286) 0.023 0.045 (1.143) (2.794) 0.045 (1.143) 0.110 0.065 (1.651) 0.015 (0.380) 0.023 (0.584) 0.045 (1.143) MIN DIMENSIONS: INCHES (MILLIMETERS) 0.065 (1.651) MAX DIMENSIONS: INCHES (MILLIMETERS) MIN MAX

0.045 (1.143) 0.065 (1.651)

0.045 (1.143) 0.065 (1.651) 0.025 (0.632) 0.030 (0.762) 0.100 0.035 (0.892) (2.540) 0.045 (1.143) 0.045 (1.143) BSC 0.065 (1.651) MIN(3.048) 0.030 (0.762) 0.120 DIMENSIONS INCHES (MILLIMETERS) MAX 0.045 (1.143) 0.150 (3.810) LEAD COPLANARITY = 0.004 INCHES (0.10 mm ) 0.030 (0.760) 0.056 (1.400) 0.120 (3.048) 0.150 (3.810) 0.100 (2.540) BSC 0.100 DIMENSIONS INCHES (MILLIMETERS) (2.540) BSC LEAD COPLANARITY = 0.004 INCHES DIMENSIONS INCHES (MILLIMETERS) LEAD COPLANARITY = 0.004 INCHES

0.047 (1.194) 0.015 (0.385) 0.370 (9.400) 0.035 (0.885) 0.070 (1.778) 0.390 (9.900) 12 NOM. 0.290 (7.370) 0.310 (7.870) 0.370 (9.400) 0.390 (9.900) 0.290 (7.370) 0.310 (7.870) 0.015 (0.385) 0.035 (0.885) 0.015 (0.385) 0.035 (0.885)

0.008 (0.203) 0.013 (0.330) 0.008 (0.203) 0.013 (0.330) 12 NOM.

0.300 (7.620) 0.370 (9.398) 0.300 (7.620) 0.370 (9.398)

0.008 (0.203) 3 0.015 (0.381) 8 3 8

0.030 (0.760) 0.056 (1.400)

0.025 (0.632) 0.035 (0.892) MIN 0.025 (0.632) MAX 0.035 (0.892) (0.10 mm ) MIN MAX (0.10 mm )

12 NOM.

SO8 SMD
0.189 (4.80) 0.197 (5.00) 8 0.228 (5.80) 0.244 (6.20) 7 6 5

Narrowbody SOIC 16 pin

8 0.228 (5.791) 0.244 (6.197) 0.228 (5.791) 0.244 (6.197) 0.013 (0.330) 0.020 (0.508) 0.013 (0.330) 0.020 (0.508) 0.386 (9.802) 0.394 (9.999) 8 1 1

0.386 (9.802) 0.394 (9.999)

Pin 1 indent

Pin 1 indent
0.152 (3.861) 0.157 (3.988) 0.152 (3.861) 0.157 (3.988)

0.150 (3.80) 0.157 (4.00)

0.189 (4.80) 2 3 4 0.197 (5.00) 5 5 0.150 (3.80) 0.157 (4.00) 0.150 (3.80) 0.004 (0.10) 0.157 (4.00) 0.010 (0.25)
0.010 (0.25) 0.020 (0.50) x 45
0.050 (1.270) 0.060 (1.524) 0.050 (1.270) 0.060 (1.524) 0.040 (1.016) 0.060 (1.524)

0.054 (1.372) 0.068 (1.727) 0.054 (1.372) 0.068 (1.727) 0.004 (0.102) 0.010 (0.249)

0.008 (0.191) 0.010 (0.249) 0.008 (0.191) 0.010 (0.249)

0.010 (0.245) x 45 0.020 (0.508) 0.010 (0.245) TYP 0 8 x 45 0.020 (0.508) 0.016 0 8 TYP (0.406) 0.050 (1.270) 0.016 (0.406) 0.050 (1.270)

0.013 (0.33) 0.189 (4.80) 6 0.020 8 (0.51) 7 0.197 (5.00)

0.228 (5.80) 0.244 (6.20) 0.228 (5.80) 0.244 (6.20) 0.054 (1.37)
0.069 (1.75)

0.008 (0.19) 0.010 (0.25)

0.040 (1.016) 0.060 (1.524) DIMENSIONS: INCHES (MILLIMETERS)

MIN MAX MIN MAX

0.004 (0.102) 0.010 (0.249)

2 3

3 4

0.013 (0.33) 0.040 (1.016) 1 2 0.020 (0.51) 0.060 (1.524)

0 8 0.016 (0.40) 0.050 (1.27) MIN MAX

DIMENSIONS: INCHES (MILLIMETERS)

0.013 (0.33) 0.020 (0.51) DIMENSIONS: INCHES (MILLIMETERS)

0.054 (1.37) 0.069 (1.75) 0.054 (1.37) 0.069 (1.75) 0.040 (1.016) 0.060 (1.524)

0.004 (0.10) 0.010 (0.25) 0.004 (0.10) 0.010 (0.25)

0.010 (0.25) 0.020 (0.50) x 45 0.010 (0.25) 0.020 (0.50) x 45

0.008 (0.19) 0.010 (0.25) 0.008 (0.19) 0.010 (0.25)

Widebody SOIC 16 pin

0 8
0.397 (10.084) 0.413 (10.490)
8

Pin 1 indent
1

0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27)

Options Available
DIMENSIONS: INCHES (MILLIMETERS)

0.040 (1.016) 0.060 (1.524) DIMENSIONS: INCHES (MILLIMETERS)

0 8

0.397 (10.084) 0.413 (10.490)

8

Pin 1 indent
1

0.394 (10.007) 0.419 (10.643) 0.394 (10.007) 0.419 (10.643)

MIN MAX MIN MAX

0.291 (7.391) 0.299 (7.595) 0.291 (7.391) 0.299 (7.595) 0.013 (0.330) 0.020 (0.508) 0.013 (0.330) 0.020 (0.508)

300 = Lead Bend SMD Option (300 mil 8 pin DIP) 500 = Tape and Reel Packaging Option xxxE = Lead Free Option
0.080 (2.032) 0.100 (2.54)

7 TYP

0.092 (2.337) 0.104 (2.642) 7 TYP 0.092 (2.337) 0.104 (2.642) 0.004 (0.1016) 0.011 (0.279) 0.004 (0.1016) 0.011 (0.279) 7 TYP 0.009 (0.229) 0.012 (0.305) 0.009 (0.229) 0.012 (0.305)

0.287 (7.290) 0.297 (7.544) 0.287 (7.290) 0.297 (7.544)

0.010 (0.254) x 45 0.020 (0.508) 0 8 TYP 0.010 (0.254) x 45 0.020 (0.508) 0.016 (0.40) 0 8 TYP 0.050 (1.27) 0.016 (0.40) 0.050 (1.27)

7 TYP
0.040 (1.016) 0.060 (1.524)

Remarks: The notation # is used for existing products, while (new) products launched since 15th July 01 will use -.

0.080 (2.032) 0.100 (2.54)

0.040 (1.016) 0.060 (1.524) DIMENSIONS: INCHES (MILLIMETERS) MIN MAX DIMENSIONS: INCHES (MILLIMETERS) MIN MAX

56

Optoisolation and Optical Sensor Products

Solid State Relay (Photo MOSFET) Package Dimensions

SO4 SMD
2.54 (0.100) LEAD FREE TYPE NUMBER DA DATE CODE
XXXX

S08 SMD
LAND PATTERN RECOMMENDATION PATTERN RECOMMENDATION 0.80 (0.031)
0.100 2.54 LEAD FREE LAND PATTERN RECOMMENDATION TYPE NUMBER DATE CODE 0.047 1.20 0.031 0.80

1.20 (0.047) 4.80 (0.189)

0.173 0.008 4.40 0.20

A XXXX YYWW

4.40 0.20 (0.173 0.008)

0.268 0.016 6.81 0.40

YWW

6.8 0.4 (0.268 0.016)

0.189 4.80

[0.015] 0.375 0.016 0.41 0.369 0.008 9.4 0.2

0.375 (0.015)

0.41 (0.016) 4.3 0.2 (0.169 0.008) 0.20 (0.008)

2.540 (0.10) 2.0 0.2 (0.079 0.009) 0.46 (0.018)

0.100 2.54 0.008 0.20 0.079 0.008 2 0.2

DIMENSIONS IN MILLIMETERS AND (INCHES). OPTION NUMBER 500 AND UL RECOGNITION NOT MARKED

0.5 (0.02)

0.102 0.102 (0.004 0.004)

0.5 (0.02)

DIMENSIONS IN MILLIMETERS AND (INCHES).

0.020 0.51

0.004 0.004 0.102 0.102

0.018 0.46

6-Pinmil 6 pin DIP 300 DIP Package

9.40 (0.370) 9.90 (0.390)
7.62 0.25 (0.300 0.010)

6-Pin DIP Package with Gull Wing Surface Mount Option 300

300 mil 6 pin DIP Gull Wing Surface Mount Option 300
LAND PATTERN RECOMMENDATION 9.65 0.25 (0.380 0.010)

6 LEAD FREE

TYPE NUMBER

6.35 0.25 (0.250 0.010)

A XXXX YYWW RU
3

DATE CODE UL RECOGNITION

6.35 0.25 (0.250 0.010)

10.9 (0.430)

PIN ONE DOT

1.78 (0.070) MAX.

1.27 (0.050)
5 TYP. + 0.076 0.254 0.051 + 0.003) (0.010 0.002)

2.0 (0.080)

4.70 (0.185) MAX. (0.020) (0.040)

1.78 (0.070) MAX. 4.19 (0.165) MAX.

0.635 0.130 (0.025 0.005)

9.65 0.25 (0.380 0.010) 7.62 0.25 (0.300 0.010)

0.20 (0.008) (0.30 0.013)

2.66 (0.105) MIN. 2.16 (0.085) 2.54 (0.100) 0.45 (0.018) 0.65 (0.025) 2.28 (0.090) 2.80 (0.110)

DIMENSIONS IN MILLIMETERS AND (INCHES)

2.29 (0.090)

2.54 (0.100) TYP.

0.635 0.25 (0.025 0.010)

12 NOM.

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

300 mil 8 pin DIP 8-Pin DIP Package

9.65 0.25 (0.380 0.010) TYPE NUMBER 8 7 A XXXX LEAD FREE YYWW RU 1 1.19 (0.047) MAX. 2 3 4 UL RECOGNITION 6 5 OPTION CODE* DATE CODE 7.62 0.25 (0.300 0.010) 6.35 0.25 (0.250 0.010)

8-Pin DIP Package with Gull Wing Surface Mount Option 300

300 mil 8 pin DIP Gull Wing Surface Mount Option 300
LAND PATTERN RECOMMENDATION 9.65 0.25 (0.380 0.010)
8 7 6 5

1.016 (0.040)

6.350 0.25 (0.250 0.010)

1 2 3 4

10.9 (0.430)

1.78 (0.070) MAX. + 0.076 0.254 0.051 + 0.003) (0.010 0.002)

1.27 (0.050)
5 TYP.

2.0 (0.080)

3.56 0.13 (0.140 0.005)

4.70 (0.185) MAX.

1.19 (0.047) MAX.

1.780 (0.070) MAX.

9.65 0.25 (0.380 0.010) 7.62 0.25 (0.300 0.010)

0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). OPTION NUMBERS 300 AND 500 NOT MARKED.

3.56 0.13 (0.140 0.005) 1.080 0.320 (0.043 0.013) 0.635 0.25 (0.025 0.010)

+ 0.076 0.254 +0.051 + 0.003) (0.010 +0.002)

1.080 0.320 (0.043 0.013)

0.65 (0.025) MAX. 2.54 0.25 (0.100 0.010)

2.54 (0.100) BSC

0.635 0.130 (0.025 0.005)

12 NOM.

DIMENSIONS IN MILLIMETERS (INCHES) LEAD COPLANARITY = 0.10mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

57

Optoisolation and Optical Sensor Products

Phototransistor Package Dimensions

300 mil 4 pin DIP
TYPE NUMBER 4 DATE CODE 3

400 mil 4 pin 0.4 Lead Spacing Option

OPTION CODE
7.62 0.3 (0.3)
4 3

7.62 0.3 (0.3)

A 817 V YYWW
1 2

6.5 0.5 (0.256)

6.5 0.5 (0.256) 2.3 0.5 (0.09)

6.9 0.5 (0.272)

PIN ONE DOT

RANK MARK
0.35 0.15/-0.10 (0.14) 7.62 ~ 9.98
1 2

4.6 0.5 (0.181) 3.5 0.5 (0.138) 3.3 0.5 (0.13) 0.5 0.1 (0.02) 2.54 0.25 (0.1) 0.5 (0.02) TYP

4.6 0.5 (0.181) 3.5 0.5 (0.138)

0.35 0.15/-0.10 (0.14) 10.16 0.05 (0.4)

2.8 0.5 (0.110)

2.8 0.5 (0.110)

DIMENSIONS IN MILLIMETERS AND (INCHES)

2.54 0.25 (0.1)

0.5 0.1 (0.02)

DIMENSIONS IN MILLIMETERS AND (INCHES)

300 mil 4 pin Lead Bend Option 300 SMD

4 3

300 mil 6 pin DIP

TYPE NUMBER 7.62 0.3 (0.3)

7.62 0.3 (0.3) 6.5 0.5 (0.256) 1.0 0.25 (0.039) 10.16 0.03 (0.4) 0.35 0.15/-0.10 (0.14)

OPTION CODE

PIN ONE DOT DATE CODE

1 2

A 4N25 V YYWW
1 2 7.3 0.5 (0.287) 3

6.5 0.5 (0.256)

0.35 0.15/-0.10 (0.14) 7.62 ~ 9.98 3.5 0.5 (0.138) 3.3 0.5 (0.13) 0.5 0.1 (0.02) 0.5 (0.02) TYP

4.6 0.5 (0.181) 3.5 0.5 (0.138) 1.2 0.1 (0.047) 2.54 0.25 (0.1) DIMENSIONS IN MILLIMETERS AND (INCHES) 0.35 0.25 (0.014)

2.8 0.5 (0.110)

2.54 0.25 (0.1)

DIMENSIONS IN MILLIMETERS AND (INCHES)

400 mil 6 pin 0.4 Lead Spacing Option

6 5 4

300 mil 6 pin Lead Bend Option 300 SMD

7.62 0.3 (0.3)
6 5 4

7.62 0.3 (0.3) 0.35 0.15/-0.10 (0.14)

6.5 0.5 (0.256) 2.3 0.5 (0.09)

1 2 3

6.9 0.5 (0.272)

6.5 0.5 (0.256) 1.0 0.25 (0.039) 10.16 0.03 (0.4)

0.35 0.15/-0.10 (0.14) 10.16 0.05 (0.4)

7.3 0.5 (0.287) 3.5 0.5 (0.138)

1.2 0.1 (0.047)

7.3 0.5 (0.287) 3.5 0.5 (0.138) 2.54 0.25 (0.1) 0.35 0.25 (0.014)

2.8 0.5 (0.110) 0.5 0.1 (0.02)

DIMENSIONS IN MILLIMETERS AND (INCHES)

DIMENSIONS IN MILLIMETERS AND (INCHES)

2.54 0.25 (0.1)

58

Optoisolation and Optical Sensor Products

Phototransistor Package Dimensions Continued

4 pin Miniat SMD
2.54 0.25 4 TYPE NUMBER 3 5.30 0.3

SO4 SMD (half-pitch)

1.27 0.25 (0.050 0.010)
DATE CODE LEAD FREE RANK MARK

181V YWW
DATE CODE 1 2

OPTION CODE
4.40 0.2 0.2 0.05

A217V YYWWA

PIN ONE DOT

RANK MARK

7.00 +0.2 -0.7

4.40 0.20 (0.173 0.008)

.75 (0.030)
VDE OPTION ONLY

3.60 0.3 2.00 0.2

.75 (0.030)
DIMENSIONS IN MILLIMETERS AND (INCHES)

0.40 0.1

0.10 0.1

Options Available
060E = IEC/EN/DIN EN 60747-5-2/5 Option W00E = 0.4 Lead Spacing Option 300E = Lead Bend SMD Option 500E = Tape and Reel Packaging Option CTR rank options can be found in products datasheet
Remarks: The notation # is used for existing products, while (new) products launched since 15th July 01 will use -.

2.60 0.30 (0.102 0.012) 2.00 0.20 (0.079 0.008)

5.30 0.30 (0.208 0.012)

0.12 0.10 (0.005 0.004) 0.40 0.10 (0.016 0.004)

7.00 0.20 (0.028 0.008) 7.00 0.40 (0.0276 0.016)

0.20 0.05 (0.008 0.002)

DIMENSIONS: INCHES (MILLIMETERS)

MIN MAX

SO8 SMD (half-pitch)

1.27 0.25 0.050 0.010 LEAD FREE DATE CODE 4.40 0.20 0.173 0.008 4.40 0.20 0.173 0.008 VDE option only

300 mil 8 pin DIP

9.68 0.50 (0.381 0.020) LEAD FREE 8 7 6 5 DATE CODE 6.50 0.50 (0.256 0.020) 7.62 0.30 (0.30 0.01) 7.62 9.98 (0.30 0.39) A 827 YYWW

PIN ONE LEAD FREE 0.75 0.030 DATE CODE PIN ONE

1.27 0.25 0.050 0.010 A224V

YYWWA

VDE option only

PIN ONE DOT 1 2 3 4

0.75 0.030 0.75 0.030

A224V YYWWA
5.20 0.30 0.205 0.012

RANK

2.00 0.20 0.079 0.008

3.50 0.50 (0.138 0.020)

0.40 0.10 0.016 0.004

0.12 0.10 0.005 0.004

2.80 0.50 (0.11 0.02)

0.50 (0.02) TYP 3.30 0.10 (0.130 0.020)

0.50 0.10 (0.02 0.00) DIMENSIONS IN MILLIMETERS AND (INCHES).

7.00 0.40 0.276 0.016 0.7 0.2 0.028 0.008 7.00 0.40 0.276 0.016

0.40 0.10 0.016 0.004

2.54 0.25 (0.10 0.01)

300 mil 16 pin DIP

19.84 0.50 (0.781 0.020) LEAD FREE 16 15 14 13 A 847 YYWW 12 11 10 9 DATE CODE 6.50 0.50 (0.256 0.02) 5 6 7 8 7.62 0.30 (0.30 0.01) 7.62 9.98 (0.30 0.39)

SO16 SMD (half-pitch)

DATE CODE LEAD FREE PIN ONE DATE CODE 0.75 0.030 1.27 0.25 0.050 0.010

LEAD FREE

1.27 0.25 0.050 0.010

VDE option only

VDE option only

PIN ONE

PIN ONE DOT 1 2 3

0.75 0.030 0.75 0.030

RANK

4.40 0.20 0.173 0.008

A244V YYWWA

4.40 0.20 0.173 0.008

A244V YYWWA

0.26 (0.01) 3.50 0.50 (0.138 0.020)

2.00 0.20 0.079 0.008

0.12 0.10 0.005 0.004

0.75 0.030

10.28 0.30 0.405 0.012 RANK

5.30 0.3 0.208 0.012

10.28 0.30 0.405 0.012 0.40 0.10 0.016 0.004

5.30 0.3 0.208 0.012 0.20 0.05 0.008 0.002 0.20 0.05 0.008 0.002 0.7 0.2 0.028 0.008 7.00 0.40 0.276 0.016 0.7 0.2 0.028 0.008 7.00 0.40 0.276 0.016

2.80 0.50 (0.11 0.02)

0.50 (0.02) TYP 3.30 0.50 (0.130 0.020)

0.50 0.10 (0.02 0.00) DIMENSIONS IN MILLIMETERS AND (INCHES).

2.00 0.20 0.079 0.008

0.40 0.10 0.016 0.004

2.54 0.25 (0.10 0.01)

0.12 0.10 0.005 0.004

0.20 0.05 0.008 0.002

0.26 (0.01)

2.00 0.20 0.079 0.008

0.75 0.030 5.20 0.30 0.205 0.012

0.12 0.10 0.005 0.004

RANK

5.30 0.3 0.208 0.012 0.7 0.2 0.028 0.008

0.20 0.05 0.008 0.002

5.30 0.3 0.208 0.012

59

Optoisolation and Optical Sensor Products

Hermetic Optocoupler Package Dimensions

16 pin Flat Pack (4 Channel)
7.24 (0.285) 6.99 (0.275) 2.29 (0.090) max

20 Terminal LCCC Surface Mount (2 Channel)

8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) 1.02 (0.040) typ (3 plcs) 1.14 (0.045) 1.40 (0.055) Terminal 1 2.16 (0.085) Metalized Castillations (20 plcs) 0.51 (0.020) typ 1.52 (0.060) 2.03 (0.080)

1.78 (0.070) 2.03 (0.080) 8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) 1.78 (0.070) 2.03 (0.080)

11.13 (0.438) 10.72 (0.422)

1.27 (0.050) ref

0.46 (0.018) 0.36 (0.014)

8.13 (0.320) max

0.64 (0.025) (20 plcs)

2.85 (0.112) max 0.88 (0.0345) min 0.89 (0.035) 0.69 (0.027) 5.23 (0.206) max 9.02 (0.355) 8.76 (0.345)

0.31 (0.012) 0.23 (0.009)

Note: Dimensions in millimeters (inches) Solder thickness 0.127 (0.005) max.

Note: Dimensions in millimeters (inches)

Option 100, Surface Mount Butt Joint, available on 8 and 16 pin DIPs
0.51 (0.020) min 4.32 (0.170) max 1.14 (0.045) 1.40 (0.055)

16 pin DIP Through Hole (2 or 4 Channel)

0.89 (0.035) 1.65 (0.065) 20.06 (0.790) 20.83 (0.820) 8.13 (0.320) max 4.45 (0.175) max

2.29 (0.090) 2.79 (0.110)

0.51 (0.020) max

0.51 (0.020) min 2.29 (0.090) 2.79 (0.110)

4.32 (0.170) max 1.14 (0.045) 1.40 (0.055) 0.51 (0.020) max 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310)

0.51 (0.020) min

3.81 (0.150) min 0.51 (0.020) max

0.20 (0.008) 0.33 (0.013)

2.29 (0.090) 2.79 (0.110)

7.36 (0.290) 7.87 (0.310)

Note: Dimensions in millimeters (inches)

Note: Dimensions in millimeters (inches)

Option 300, Surface Mount Gull Wing, available on 8 and 16 pin DIPs
0.51 (0.020) min 4.57 (0.180) max 1.40 (0.055) 1.65 (0.065)

2.29 (0.090) 2.79 (0.110)

0.51 (0.020) max

8 pin DIP Through Hole (1 or 2 Channel)

9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 8.13 (0.320) max 7.16 (0.282) 7.57 (0.298) 0.51 (0.020) min 2.29 (0.090) 2.79 (0.110) 4.57 (0.180) max 1.40 (0.055) 1.65 (0.065) 0.51 (0.020) max

5 max 0.20 (0.008) 0.33 (0.013) 9.65 (0.380) 9.91 (0.390)

4.57 (0.180) max

1.07 (0.042) 1.32 (0.052)

4.32 (0.170) max 0.51 (0.020) min 0.20 (0.008) 0.33 (0.013)

Note: Dimensions in millimeters (inches)

3.81 (0.150) min

0.51 (0.020) max

7.36 (0.290) 7.87 (0.310)

Option 600, Surface Mount Short Butt Joint, available on 8 and 16 pin DIPs
0.51 (0.020) min 3.81 (0.150) max 0.51 (0.020) min 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) 2.29 (0.090) 2.79 (0.110) 1.02 (0.040) typ 3.81 (0.150) max

Note: Dimensions in millimeters (inches)

2.29 (0.090) 2.79 (0.110)

1.14 (0.045) 1.25 (0.049)

60

Note: Dimensions in millimeters (inches)

Optoisolation and Optical Sensor Products

Function vs Application Matrix

Function
Market Application

Digital Isolation
Power Device Drive Inverter IPM Automated Test Equipment Board CPU Elevator FFT/Data Logger Industrial Induction Cooking Industrial Networking Instrument Motor Control NC/Robot On-board Power Supply 9, 16 9 16, 20 20 9 20 9 20 Data Communication Field Bus RS422/485 Others 8 8, 16 1, 6 1, 6, 16 3, 4, 5, 11, 17, (18) 3, 4, 5, 11, 16, 17, (18) 17 17 17 7, 8, (18) 1, 6, (18) 3, 4, 5, 11, 17, (18) 8, 16 7, 8, 16 7, 8 1, 6, 16 6, 16 6 3, 4, 5, 11, 16, 17, (18) 3, 4, 5, 11, 16, 17, (18) 3, 4, 5, 11, 17, (18) 16, 17 8 1, 6 3, 4, 5, 11, 17, (18) 6, 16, (18) 6, 16, (18) 6, (18) 6, 16, (18) 6, (18) 6, (18) 2, 6, (18) 13 13, 16 6, (18) 2, 6, (18) 13 2, 6, 16, (18) 13, 16 13 6, 7, 16, (18) 6, 16, (18) A-D Isolation ADC/DAC V-F Converter 2, 6, (18) 2, 6, 16, (18) 13 Voltage Monitor 13

Analog Isolation
Current Voltage Sensing Sensing Signal Amp Signal Powerline Power Switching Comm Supply Feedback 21

10

10, 14, 15

21

10

10, 14, 15

16, 21 10, 16 10 10, 14, 15, 16 10, 14, 15 16, 21 21

17 17

17 21 21 16, 21 14, 15 21 21 19 17 17 17 17 21 17

Industrial

Panel Switches PLC Power Distribution System Process Meter Remote Meter Reading Servo Driver Sewing Machine Solar Generator Switching Power Supply Test & Measurement Equipment Thermo Counter/Recorder Welding De brillator Electrocardiograph (ECG/EKG) Endoscopes 9 9 20 9, 16 9 9 9, 16 16, 20 20 20 16, 20 9, 16 16, 20

7, 8, (18) 1, 6, (18) 3, 4, 5, 12, 17, (18) 8, 16 3, 4, 5, 12, 16, 17, (18)

7, 8, (18) 1, 6, (18) 12, 17, (18)

7, 8, 16

6, 16

3, 4, 5, 11, 16, 17, (18) 17

6, 16, (18)

13, 16 13 13

10, 16 10 10 10, 16

10, 14, 15, 16 10, 14, 15 10, 14, 15 10, 14, 15, 16

17 17

7, 8, (18) 1, 6, (18) 3, 4, 5, 11, 17, (18) 8, 16 6, 16 3, 4, 5, 11, 16, 17, (18)

6, (18) 6, 16, (18) 2, 6,16, (18)

13

13

10

10, 14, 15

6, 7 (18) 6, 7 (18) 6, 7 (18) 6, 7 (18) 7, 8 9 6, 7 (18) 6, 7 (18)

6, 7 (18) 6, 7 (18) 6, 7 (18) 6, 7 (18) 6, 7 (18) 6, 7 (18)

10

10, 14

10 10 10

Medical

Esophagus Photoplethysmography (PPG) Magnetic Resonance Imaging (MRI) 9 Patient Monitoring X-Ray

10

10 10

10

Note: Number in bracket ( ) indicates non-optical isolation product 1. 2. 3. 4. 5. 3.3V Digital Optocoupler Family 1 MBd Transistor Output Optocoupler 100 kBd Darlington Transistor Output Optocoupler 5 MBd Logic Gate Optocoupler 8 MBd Logic Gate Optocoupler 6. 10 MBd Logic Gate Optocoupler 7. 20 MBd Logic Gate Optocoupler 8. High Speed Digital CMOS Logic Gate Optocoupler 9. Integrated Gate Drive Optocoupler 10. Miniature Analog Isolation Amplifier 11. Isolated Line Receiver 12. Isolated 20 mA Current Loop Transmitter/Receiver 13. AC/DC to Logic Interface 14. High Linearity Analog Optocoupler 15. Wideband Analog/Video Optocoupler 16. Hermetic High Performance Optocoupler 17. General Purpose Phototransistor Optocoupler 18. Digital Isolator 19. Powerline Communication Interface 20. Intelligent Power Module Interface Optocoupler 21. Solid State Relay (Photo MOSFET) 22. Automotive Optocoupler

61

Optoisolation and Optical Sensor Products

Function vs Application Matrix Continued

Function
Market Application

Digital Isolation
Power Device Drive Inverter IPM Inverter AC-DC / DC-DC Converter Charger 9, 22 9, 22 9, 22 20, 22 20, 22 Data Communication Field Bus RS422/485 Others 2, 6, 22 2, 6, 22 2, 6, 22 2, 6, 22 9, 22 9, 22 9, 22 20, 22 20, 22 2, 6, 22 2, 6, 22 2, 6, 22 2,4,5,6 2,4,5,6 2,4,5,6 2,4,5,6 9 9 20 20 6 9 9 20 20 6, 17, (18) 2, 6, 8, 9, 17 9 9 20 20 1,2,3 1,2,3 17 17 7, 8, 17 3, 17 13 13 2, 22 6, 7, 8, 17, (18) 6, 7, 8, 17, (18) 6, 7, 8, 17, (18) 6, 7, 8, 17, (18) 8, 17 17 6, 17, (18) 13 13 2, 22 2, 6, 22 2, 22 A-D Isolation ADC/DAC V-F Converter 2, 22 2, 22 2, 22 Voltage Monitor

Analog Isolation
Current Voltage Sensing Sensing 10, 22 10, 22 10, 22 10, 22 10, 22 10, 22 2, 22 2, 22 Signal Amp Signal Powerline Power Switching Comm Supply Feedback

Automotive

Battery Management Oil Pump Heater Aircon ECR, POS

10, 22

10, 22 17

Computing and Office Automation

Isolated I/O Isolated USB Network UPS Air Conditioning Electronic Gaming Fitness Equipment

21 10 10 10, 14, 15 21 17 17 17 10 10 17

Consumer

Induction Heating Cookers Musical (MIDI) Plasma Displays Refrigerator Washing Machines ISDN PBX and Central Office Power Line Communication

21 21 21 21 21 19

17 17 17 17

Communications Power-Over-Ethernet (PoE) Telephone Switching Equipment Telephone Terminal Equipment Wireless Base Station Military/ Aerospace/Harsh Industrial 16 16

7, 8

1, 6 6, 7, 8, 17, (18) 6, 7, 8, 17, (18) 6, 7, 8, 17, (18) 21 21 21 16 16 16 16 16 16 16 17 17 17 16

16

16

16

Note: Number in bracket ( ) indicates non-optical isolation product 1. 2. 3. 4. 5. 3.3V Digital Optocoupler Family 1 MBd Transistor Output Optocoupler 100 kBd Darlington Transistor Output Optocoupler 5 MBd Logic Gate Optocoupler 8 MBd Logic Gate Optocoupler 6. 10 MBd Logic Gate Optocoupler 7. 20 MBd Logic Gate Optocoupler 8. High Speed Digital CMOS Logic Gate Optocoupler 9. Integrated Gate Drive Optocoupler 10. Miniature Analog Isolation Amplifier 11. Isolated Line Receiver 12. Isolated 20 mA Current Loop Transmitter/Receiver 13. AC/DC to Logic Interface 14. High Linearity Analog Optocoupler 15. Wideband Analog/Video Optocoupler 16. Hermetic High Performance Optocoupler 17. General Purpose Phototransistor Optocoupler 18. Digital Isolator 19. Powerline Communication Interface 20. Intelligent Power Module Interface Optocoupler 21. Solid State Relay (Photo MOSFET) 22. Automotive Optocoupler

62

Optoisolation and Optical Sensor Products

Optical Sensors
Proximity Sensors
Avago Technologies offers a full range of Optical Proximity Sensors to meet the requirements of todays industrial and consumer applications. The basic construction of an optical proximity sensor consists of an IR LED and a photodiode. The LED and the photodiode of an Avagos proximity sensor are housed in a specially designed metal-shield to ensure excellent optical isolation. The result is a small size device with low optical crosstalk and excellent power efficiency. Avago proximity sensors are offered in a variety of options in terms of features, packages and level of integration. Product offerings range from discrete to fully integration modules and choice of analog or digital output. These devices offer engineers the widest selection of features and the design flexibility to meet a variety of performance applications.

Ambient Light Sensor

Avago Technologies o ers a series of Ambient Light Sensors that provide precise light detection for a wide range of ambient brightness. These devices are designed with close-to-human-eye spectral response that mimic human eyes perception and hence provide consistent performance under di erent light sources such as sunlight, uorescent and incandescent. These Sensors are packaged in miniature chipLED lead-free, RoHS compliance surface mount package and especially suited for mobile phones and portable devices. It is commonly use in mobile phone to enable auto LCD backlight adjustment and key pad lighting depending on the surrounding ambient brightness to achieve optimum viewing comfort and save battery power.

Integrated Ambient Light and Proximity Sensor

Part Number Size (LxWxH) (mm) Supply Voltage (V) ALS Dynamic Range Max. Detection Distance PS Output ALS Output

APDS-9900

3.94 x 2.36 x 1.35

2.5 to 3.6

0.01 to 10k lux

Near zero to 100mm

I2C Digital count output

I2C Digital count output

Optical Proximity Sensor

Part Number Size (LxWxH) (mm) Supply Voltage (V) Max. Detection Distance PS Output

APDS-9100 APDS-9190

7.10 x 2.75 x 2.7 3.94 x 2.36 x 1.35 2.5 to 3.6

Near zero to 100mm Near zero to 100mm

Analog I2C Digital count output

Proximity Sensing Conditioning IC

Part Number Size Supply Voltage (V) Max. Detection Distance PS Output

APDS-9700 APDS-9702

QFN 2 mm x 2 mm QFN 2 mm x 2 mm

2.4 to 3.6 2.4 to 3.6

Near zero to 60mm Near zero to 60mm

Analog (with HI/LO digital o/p) Analog (with HI/LO digital o/p)

Ambient Light Sensor

Part Number Size (LxWxH) (mm) Package Supply Voltage (V) Typical Output Current @ 100 Lux (uA)

APDS-9002 APDS-9003 APDS-9004 APDS-9005 APDS-9006 APDS-9007 APDS-9008 APDS-9300 APDS-9301 APDS-9303

2.0 x 1.25 x 0.8 1.60 x 1.5 x 0.55 3.2 x 1.6 x 1.1 1.60 x 1.5 x 0.55 3.2 x 1.6 x 1.1 2.4 x 2.0 x 0.8 x 1.60 x 1.5 x 0.55 2.6 x 2.2 x 0.55 2.6 x 2.2 x 0.55 2.6 x 2.2 x 0.55

4 pin - ChipLED 6 pin - ChipLED 4 pin - ChipLED Reverse mounting 6 pin - ChipLED 4 pin - ChipLED Reverse mounting 6 pin - ChipLED 6 pin - ChipLED 6 pin - ChipLED 6 pin - ChipLED 6 pin - ChipLED

2.4 to 5.5 2.4 to 5.5 2.4 to 5.5 1.8 to 5.5 2.4 to 5.5 2.0 to 3.6 1.6 to 5.5 2.4 to 3.0 2.7 to 3.6 2.7 to 3.6

250 230 230 40 40 30 uA at 1Klux (Logarithmic output) 40 I2C Digital count output I2C Digital count output SMBus Digital count output 63

Your Imagination. Our Innovation

From the smartphone that keeps you in touch, to the ber optic network that keeps a $10-billion corporation connected, we get our information these days through an ever-increasing array of sophisticated device technologies. And behind it all, are semiconductors that sense, illuminate, and connect the signals in order to process that digital data. Avago Technologies is a leading supplier in III-V compound and silicon semiconductors providing an extensive range of analog, mixed signal and optoelectronics components that are backed by over 5,000 patents to approximately 40,000 end customers. Our heritage of technical innovation dates back 45 years, and includes over 1,000 talented design and product engineers. We believe in strong customer service support and intense collaboration to create leading-edge proprietary technologies to solve customers technical bottlenecks. In that way - Our innovation helps bring your imagination to market.

Avago products serve four diverse end markets

Wireless Communications serving the smartphone/handset and Base Station infrastructure markets with over 250 patents and leading-edge products that include: Power Amplifiers Front End Modules Film Bulk Acoustic Resonator (FBAR) Filters GPS LNAs LED Backlighting, Screen Illumination Ambient Light and Proximity Sensors Wired Infrastructure for switches/routers, data centers, supercomputers and storage/ servers with over 200 patents in parallel optics alone and products that include: 120Gb Parallel Optic Arrays 20Gb SerDes ASICs in 40nm Storage Fibre Channel Transceivers QSFP/SFP Sonet Transceivers Motion Control Optical Encoders Paper Level/Edge Proximity Sensors Display LEDs Status Indicator and Backlighting LEDs Ambient Light Photo Sensors Auto Focus Auxiliary Flash LED Industrial and Automotive Electronics for alternative energy power generation, electronic sign and signals, automated manufacturing, automotive lighting, GPS navigation, motor inverter system, battery charging and management, infotainment systems and vehicle safety systems with products that include: Inverters Isolation and Digital Optocouplers Optical Encoders Polymer Optical Fiber PLCC-2/4 LEDs, 0.5W LEDs Consumer and Computing peripherals for printers, white goods, DVD players, netbooks, Tablet PCs and laptops with over 100 patents and products that include:

For product information and a complete list of distributors, please go to our web site:

www.avagotech.com www.avagotech.com/optocouplers www.avagotech.com/hermetic-optocouplers www.avagotech.com/sensors

For technical support please email a Technical Response Center in your region: United States: support@avagotech.com Europe: info@promotionteam.de Asia Paci c: pacrim.components@avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright 2012 Avago Technologies AV00-0254EN 05/16/2012