P R O D U C T D ATA S H E E T

ACTUATOR LA36
Features: 12, 24 or 36 V DC Permanent magnetic tic motor Thrust from 500 N - 10.000 N depending ding on gear ratio and spindle pitch 10.000 N actuator cannot be ordered d without electrical endstop 10.000 N actuator can be ordered in push and pull Max. speed up to 160 mm/sec. depending ding on load and spindle pitch Heavy duty aluminium housing for harsh conditions Highly efficient acme thread spindle Protection class: IP66 for outdoor use e (dynamic), furthermore the actuator can be washed down by a high pressure sure cleaner (IP69K - static) Hand crank for manual operation Mechanical overload protection through integrated slip clutch (adjusted to 1.2-1.5 times max. load) Integrated brake, high self-lock ability End play 2 mm max. Non rotating piston rod eye Back fixture turnable in steps of 30 degrees Noise level: 73 dB (A) measuring method DS/EN ISO 8746 actuator not loaded Options: Built in end stop switches Adjustable magnetic sensors for end stop signals (code no. 1017031) Hall effect sensor with A/B signal Potentiometer full scale at 333 mm stroke with 8 mm pitch, 500 mm stroke with 12 mm pitch and 833 mm with 20 mm pitch Analog feedback for precise positioning Different back fixtures and piston rod eyes Exchangeable cables in different lengths Resetable thermal overload protection Usage: Duty cycle at max. load 20% (up to 600 mm stroke, for strokes between 601-999 mm the max. duty cycle is 15%) at ambient temperature 25C N.B. 10.000N 5% duty cycle. Ambient operating temperature -30C to +65C full performance from 5 - 40C

LA36 is ideal for use in harsh conditions. It is a solid actuator based on the philosophy that it must be able to operate under extreme conditions. The actuator is ideal for mobile off-highway equipment such as agricultural, forestry and construction machines.

iFLEX is the new sub-brand under which every TECHLINE actuator with built-in intelligence is unified e.g. LINBUS and MODBUS. For more information on iFLEX, please see: www.linak.com/techline

Technical specications
LA36 with 12V motor
Order number Push max. (N) Pull max. (N) *Self-lock min. (N) Push *Self-lock min. (N) Pull Pitch (mm/spindle rev.) Typical speed (mm/s) Load no 362CXXXXXXXXAXX 363AXXXXXXXXAXX 363BXXXXXXXXAXX 363CXXXXXXXXAXX 365AXXXXXXXXAXX 365FXXXXXXXXAXX 10000 2600 4500 6800 1700 500** 10000 2600 4500 6800 1700 500** 13000 3400 5800 8800 2200 1000 13000 3400 5800 8800 2200 1000 8 12 12 12 20 20 11 40.7 23.1 15.5 68 160 full 7 30.6 17.8 11.9 52 135 Standard stroke lengths (mm) In steps of 50 mm 100 - 999* 100 - 999 100 - 999* 100 - 999* 100 - 999 100 - 999 Typical amp. (A) 12 V No load 4.5 4.5 4.5 4.5 4.5 4.5 Full load 22 21 20.7 21 22 20

LA36 with 24V motor

Order number Push max. (N) Pull max. (N) *Self-lock min. (N) Push *Self-lock min. (N) Pull Pitch (mm/spindle rev.) Typical speed (mm/s) Load no 362CXXXXXXXXBXX 363AXXXXXXXXBXX 363BXXXXXXXXBXX 363CXXXXXXXXBXX 365AXXXXXXXXBXX 365FXXXXXXXXBXX 10000 2600 4500 6800 1700 500** 10000 2600 4500 6800 1700 500** 13000 3400 5800 8800 2200 1000 13000 3400 5800 8800 2200 1000 8 12 12 12 20 20 11 41 23.3 15.7 68 160 full 7 32.3 18.9 12.7 52 135 Standard stroke lengths (mm) In steps of 50 mm 100 - 999* 100 - 999 100 - 999* 100 - 999* 100 - 999 100 - 999 Typical amp. (A) 24 V No load 2.4 2.4 2.4 2.4 2.4 2.4 Full load 10.4 10.4 10.2 10.3 10.3 10.0

LA36 with 36V motor

Order number Push max. (N) Pull max. (N) *Self-lock min. (N) Push *Self-lock min. (N) Pull Pitch (mm/spindle rev.) Typical speed (mm/s) Load no 362CXXXXXXXXCXX 363AXXXXXXXXCXX 363BXXXXXXXXCXX 363CXXXXXXXXCXX 365AXXXXXXXXCXX 365FXXXXXXXXCXX 10000 2600 4500 6800 1700 500** 10000 2600 4500 6800 1700 500** 13000 3400 5800 8800 2200 1000 13000 3400 5800 8800 2200 1000 8 12 12 12 20 20 11 41 23.3 15.7 68 160 full 7 33.5 19.1 12.8 52 135 100 - 999* 100 - 999 100 - 999* 100 - 999* 100 - 999 100 - 999 Standard stroke lengths (mm) In steps of 50 mm Typical amp. (A) 36 V No load 2.0 2.0 2.0 2.0 2.0 2.0 Full load 8.0 8.0 8.0 8.0 8.0 8.0

* There are limitations on the stroke length if you need full load, please see LA36 Load v. Stroke Length ** Note: Fully loaded actuators need a softstart in order to prevent the clutch slipping at start (see curves).

Speed and current curves:

LA36 12V motor current vs load

25 20
LA365A LA363A LA363B LA365F*

LA36 12V motor speed vs load

180

LA363C

LA362C

160 140 Speed (mm/s) 120 100 80 60 40 20 0

LA365A
LA363A LA363B LA363C LA362C LA365F*

Ampere

15 10 5 0 0 2000 4000 6000 Load (N) 8000 10000 12000

2000

4000

6000 Load (N)

8000

10000

12000

LA36 24V motor current vs load

12
LA365F* LA365A LA363A LA363B LA363C

LA36 24V motor speed vs load

180 160 140 Speed (mm/s) 120 100 80 60 40 20 0
LA365A
LA363A LA363B LA363C i h LA362C LA365F*

10 8 Ampere 6 4 2 0 0 1000 2000 3000 4000 Load (N) 5000 6000 7000 8000

2000

4000

6000 Load (N)

8000

10000

12000

10.000N not tested

LA36 36V motor current vs load

9 8 7 6 Ampere 5 4 3 2 1 0 0 1000 2000 3000 4000 Load (N) 5000 6000 7000 8000
Speed (mm/s)
LA365F* LA365A LA363A LA363B LA363C

LA36 36V motor speed vs load

180 160 140 120 100 80 60 40 20 0 0 2000 4000 6000 Load (N) 8000 10000 12000
LA365A
LA363A LA363B LA363C i h LA362C LA365F*

10.000N not tested

* Speed and current based on nominal power supply of 12, 24, 36VDC.

LA36
Ordering example:
36 3 A 1 1 + 0 0 x x x A 2 0 Cable:
0 = No cable 1 = 1.5 m power cable 2 = 5 m power cable 3 = 0.2 m power cable with AMP connector 4 = 1.5 m power and 1.5 signal 5 = 5 m power and 5 m signal 6 = 1.5 m Y-cable, power and signal in one 2 = Standard (IP66) A = 12 V DC with clutch B = 24 V DC with clutch C = 36 V DC with clutch

IP-degree: Motor type:

Stroke length:

XXX = mm

Acme spindle: 100, 150....999 mm

Feedback:

0 = Standard (No feedback) B = Analog feedback 0 - 10V C = Analog feedback 0.5 - 4.5V H = Hall signal P = Potentiometer (not possible with CS36) 0 = No limit switches (not for spindle 2 and A) 1 = With limit switches 2 = With limit switches and end-stop signals 3 = CS36 4 = CS36 with end-stop signals + = Without safety nut - Standard S = With safety nut - only in push 0 = M20 X 1 female adapter 1 = 12.9 mm hole, for 1/2" pin 2 = 12.2 mm hole, for 12 mm pin 3 = M12 X 1.75 male adapter 4 = M16 X 1.5 male adapter 5 = 12.2 hole with slot (like LA34) A = 12.2 mm hole with slot - AISI 304 B = 12.9 mm hole with slot - AISI 304 C = Ball eye 12.2 D = Ball eye 16 0 = M20 X 1 female adapter 1 = 12.9 mm hole, for 1/2" pin 2 = 12.9 mm hole turned 90, for 1/2" pin 3 = 12.2 mm hole, for 12 mm pin 4 = 12.2 mm hole turned 90, for 12 mm pin 5 = M12 X 1.75 male adapter 6 = M16 X 1.50 male adapter 7 = 12.2 hole with slot (like LA34) 8 = 12.2 hole with slot (like LA34) turned 90 A = 12.2 mm hole with slot - AISI 304 B = 12.2 mm hole with slot turned 90 degrees in AISI 304 C = 12.9 mm hole with slot - AISI 304 D = 12.9 mm hole with slot turned 90 degrees - AISI 304 8 mm pitch N.A. N.A. 10.000 N N.A. 12 mm pitch 2.600 N 4.500 N 6.800 N N.A. 20 mm pitch 1.700 N N.A. N.A. 500 N

End stop:

Safety nut: Piston rod eye:

Back fixture:

Gearbox:

A = Gear ratio 1 : 18 B = Gear ratio 1 : 31 C = Gear ratio 1 : 46 F = Gear ratio 1 : 7

Spindle type:

2 = 2-threaded acme spindle (8 mm pitch) 3 = 3-threaded acme spindle (12 mm pitch) 5 = 5-threaded acme spindle (20 mm pitch) A = 2 + adjustable reed limit switches (on outer tube) C = 3 + adjustable reed limit switches (on outer tube) E = 5 + adjustable reed limit switches (on outer tube) 36 = LA36

Actuator type:

NB: When ordering AISI piston rod eye and back xture, stainless steel screws are automatically included. When ordering standard stroke length with end-stop 1, 2, 3, 4 or 5 the stroke length will be 3-4 mm shorter.

LA36 dimensions:

When STROKE <= 300 = Installation dimension: 200 + STROKE LENGTH When STROKE >300 = Installation dimension: 250 + STROKE LENGTH

02= Turned 90

01= Standard

I/O specifications: Power supply - Motor

Item Power supply Input voltage 12 VDC, 20% 24 VDC, 10% 36 VDC, 10% 20% at max. load 2 - 22 Amp. depending on load and voltage (see graphs) To extend actuator: Connect Brown to positive Connect Blue to negative To retract actuator: Connect Brown to negative Connect Blue to positive Note: Please note on varients with fast gear (500N-LA365F), it is necessary to use soft start to avoid the actuator clutch slipping when started. Actuator direction can be controlled with a double-throw switch with the middle position off Cable dimension: 2 x 2.5mm (2 x AWG14) for all different voltages. Specification Comment

Duty cycle Current consumption Connection

Ambient temperature 25C

Positioning feedback Potentiometer

Item Absolute positioning Potentiometer Output range with 8 mm spindle pitch Output range with 12 mm spindle pitch Output range with 20 mm spindle pitch Linearity Output protection Connection Bourns 0 - 10 K ohm A 5%, 10-Turn 0 K ohm = 0 mm stroke 10 K ohm = 333 mm stroke 0 K ohm = 0 mm stroke 10 K ohm = 500 mm stroke 0 K ohm = 0 mm stroke 10 K ohm = 833 mm stroke 0.25% 1 Kohm protection resistor Common - = Black +10V exitation = White 0 = 10V out = Violet +10V or other value Type: 3540 Wirewound The same for all LA36 8 mm models e.g. 166.6 mm stroke = 5 Kohm The same for all LA36 12 mm models e.g. 250 mm stroke = 5 Kohm The same for all LA36 20 mm models e.g. 416.5 mm stroke = 5 Kohm Specification Comment

Note:

Please note that Potentiometer is not possible on varients with fast gear (LA365F) -500N.

Positioning feedback Hall sensors.

Item Relative positioning Signal description Input Voltage Output voltage Can be used for both direction and positioning 12 - 36 V DC Always the same as input voltage Note: max. output voltage 24V DC 12V : 11V 1V 24V : 23V 1V 36V : 23V 1V LA362C: Actuator = 0.1 mm per count. LA363C: Actuator = 0.2 mm per count. LA363B: Actuator = 0.3 mm per count. LA363A: Actuator = 0.4 mm per count. LA365A: Actuator = 0.7 mm per count Movement per single Hall pulse: LA362C Actuator = 0.4 mm per pulse LA363C Actuator = 0.7 mm per pulse LA363B Actuator = 1.0 mm per pulse LA363A Actuator = 1.7 mm per pulse LA365A Actuator = 2.9 mm per pulse Frequency Frequency is 14-26 Hz on A signal (and the same on B signal) depending on load. Every pulse is ON for 10 ms There is a phase shift of 90 30 between the phases 15 mA 40 mA, max. pr. channel Supply = Red Hall A = Yellow Hall B = Green Common - = Black
Hall A Hall B Input to PLC

Specification

Comment

Cable dimension: 6 x 0.5 mm (6 x AWG20) for all different voltages

Resolution (Distance the piston rod moves per count)

The Hall sensor signals are generated by the turning of the actuator gearing. These signals can be fed into a PLC (Programmable Logic Controller). In the PLC the quadrature signals (fig. 1) can be used to register the direction and position of the piston rod. N.B. For more precise measurements, please contact LINAK.

Low frequency with a high load Higher frequency with no load

Current consumption Switching capacity Connection

Also when actuator is not running Max. 680 nF

Diagram:
Quadrature Count Represents direction and position.

Fig. 1

I/O Specification: Analog feedback

Item Description Specification The actuator can be equipped with electronic circuit that gives an analog feedback signal when the actuator moves 12 - 36 V DC Feedback circuit to be powered 1 second before motor runs, and until 1 second after the motor has stopped. Cable dimension 6 x 0,5 mm2 (6 x AWG20) +/- 0.3 V Comment

Input voltage

Output voltage

0 -10 V 0V = Fully retracted 10V = Fully extended 0,5-4,5V (Option C) 0,5V = Fully retracted 4,5V = Fully extended

Current consumption Connection

Max. 40 mA Supply: White (Pin 3) (+12V to 36V) Ground: Black (Pin 1) Signal: Violet (Pin 4) (0 10V Out) The Absolute positioning shall be combined with limit switches. Can be combined with ends stop signal

Also when actuator is not running Use cable 0367003-XXXX

Combinations

36xxxxx1Bxxxxxx/36xxxxx1Cxxxxxx 36xxxxx2Bxxxxxx/36xxxxx2Cxxxxxx

Note:

It is recommendable to have the actuator to activate its limit switches on a regular basis. End stop signal: max 20 mA available.

End stop signal: max 20 mA available I/O Specication: PLC option. For more details contact LINAK.

LA36 Piston Rod Eye

LA36 Back Fixture

LA36 Load versus Stroke Length 10000

(8 mm)

6800 Load - Push (N)

(12 mm) (12 mm) (12 mm) (20 mm) (20 mm)

4500 2600 1700 500

N.B. LA36 500 - 1.700 N is with 20 mm spindle pitch LA36 500 - 6.800 N is with 12 mm spindle pitch LA36 500 - 10.000 N is with 8 mm spindle pitch

200

400

600

800

1000

Stroke Length (mm)

For applications that only operate in pull the limitations are 999 mm stroke and 10,000 N load. The Piston Rod Eye is only allowed to turn 0-90 degrees Safety factor 2

Manual hand crank

The manual hand crank can be used in the case of power failure. The cover over the Allen Key socket must be unscrewed before the Allen Key can be inserted and the Hand Crank operated. Hand Crank Torque: Max.16 Nm (at maximum load) Piston Rod movement per turn Gear A = 10.5 mm Gear B = 6.0 mm Gear C = 4.0 mm Gear F = 27 mm

6 mm Allen key

Note: The power supply has to be disconnected during manual operation. If the actuator is operated as a Hand crank, it must be operated by hand or carefully by machine, otherwise there is a potential risk of overloading and hereby damaging the actuator. LA36 with CS or MODBUS options only operate by hand. With stainless steel screws: 5 mm Allen Key

The LA36 is tested according to the following standards:

Test Cold test Dry heat Change of temperature Damp heat Specification: EN60068-2-1 (Ab) EN60068-2-1 (Ad) EN60068-2-2 (Bb) EN60068-2-2 (Bd) EN60068-2-14 (Na) EN60068-2-30 (Db) EN60068-2-3 (Ca) Salt spray Degrees of protection Chemicals Free fall Vibration EN60068-2-36 (Fdb) EN60068-2-6 (Fc) Bump Shock Power supply HF-immunity Emission Insulation test Automotive transients ISO 7637 EN60068-2-29 (Eb) EN60068-2-27 (Ea) ASAE EP455 (1990) EN61000-6-2 EN61000-6-4 EN60068-2-52 (Kb) EN60529-IP66 BS7691/96 hours Comment Storage at low temperature: -40C Operating at low temperature: -30C Storage at high temperature: +90C Operating at high temperature: +60C Rapid change in temperature: +100C to -30C Damp heat, Cyclic: Relative humidity 93 - 98 % High +55C, low +25C Damp heat, Steady: Relative humidity 93 - 95 % +40C 2C Salt spray test: 500 hours incl. spraying periods + humidity storage IP6X Dust: Dust-tight IPX6 Water: No ingress of water causing damage Resistant against: diesel, hydraulic oil, ethylene glycol, urea nitrogen, liquid lime, NPK fertilizers Free fall from all sides: 0.4 meters on to steel Random vibration: Short time 6.29 g RMS (Rod Mean Square) Long time 7.21 g RMS Sinus vibration: Freq. 5 - 25 Hz, amplitude = 3.3 mm pp Freq. 25 - 200 Hz, acceleration 4 g Bump test: Level 40 g for 6 milliseconds. 3,000 bumps Shock test: Level 100 g for 6 milliseconds Operating voltages: +10 V - + 16V Over voltage +26(V) / 5 min Level: 30V/m. at 26 MHz 1000 MHz; 80% 1 KHz All levels are well within the norms of the emission standards Level: 500 V AC/25-100 Hz for 1 minute Load dump test only accepted on motor power connection
Copyright LINAK 2012.04 MA M9-02-148-M . Chapter 5.12 Terms of use The user is responsible for determining the suitability of LINAK products for specic application. LINAK takes great care in providing accurate and up-to-date information on its products. However, due to continuous development in order to improve its products, LINAK products are subject to frequent modications and changes without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products. While LINAK uses its best efforts to full orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK. All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.