The Safety Assessment Federation Ltd
Page 1 of 3
Guidance on the thorough examination of fibre slings
Number: MLCC 10
Prepared by: Machinery Lifts and Crane Committee (MLCC)
Status: Issue 01 Date: 8
th
September 2008
Reference: Fibre Slings
1. INTRODUCTION
Fibre slings are widely used in many industrial sectors including construction, marine, aviation,
manufacturing and general engineering. They can be used for a variety of purposes including lifting,
handling, and securing loads. There is a wide range of possible causes of degradation of all types of
fibre slings which should be considered and assessed.
2. LEGAL REQUIREMENTS
Under the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER), fibre slings are
termed accessories for lifting. They are also work equipment within the meaning of the Provision
and Use of Work Equipment Regulations 1998 (PUWER).
The key requirements for fibre slings under the provisions of LOLER and PUWER are:
Suitability must be suitable for the purpose for which it is to be used or provided.
Safe use must be clearly marked with its safe working load (SWL) and must not be operated
above its SWL.
Information and training employers are required to ensure that employees are adequately
informed, instructed and trained in the safe use of equipment.
Maintenance must be maintained in an efficient state, in efficient working order and in
good repair.
Thorough examination must be thoroughly examined by a competent person at least every
6 months, or in accordance with a scheme of examination. Records of thorough examination
should be made in accordance with the prescribed particulars contained within the LOLER,
Schedule 1.
Inspection must be visually inspected prior to use or on a regular basis. The interval
between inspections will depend on the conditions of service. Where fibre slings are used in
environments where they can be easily damaged, they should be visually inspected on each
occasion prior to use. If any defects are found, the sling should be withdrawn from service and
subjected to a further thorough examination.
3. STANDARDS
There are many European Harmonised Standards detailing design and construction of fibre ropes and
belts manufactured from a variety of different materials including:
BS EN 14921: 2000 Textile Slings Safety Flat woven webbing slings made of man-made
fibres for general purpose use.
BS EN 14922: 2000 Textile Slings. Safety. Roundslings made of man-made fibre ropes for general
purpose use.
BS EN 14924: 2004 Textile Slings Safety Lifting slings for general purpose made from
natural and man-made fibre ropes.
The Safety Assessment Federation Ltd
Page 2 of 3
4. EQUIPMENT CHARACTERISTICS
Accessories for lifting should be carefully selected after a suitable and sufficient risk assessment has
been completed for the particular work activity.
Fibre slings can be made from natural fibres such as sisal, manila and hemp or man made materials
such as nylon, polyester and polyethylene. Two of the most common fibre sling constructions are
round rope slings typically made of 3, 4 or 8 plaited strands of fibres and flat belt slings where the
fibres are commonly woven and enclosed by a protective casing sleeve. They can be made as endless,
single leg or multiple legs with master links, couplings and thimbles.
Certification in the form of a declaration of conformity and the visible marking of safe working loads
are statutory requirements and should be made available for scrutiny as deemed necessary at the time of
the thorough examination.
5. EXAMINATION CONSIDERATIONS
Some of the more important points which need to be considered when carrying out a thorough
examination are as follows:
Assess the suitability of the marking of the Safe Working Load (SWL) on the fibre sling
Assess the suitability and legibility of the unique identification number
Assess the extent and severity of soiling. Heavy soiling can obscure damage, making detection
difficult. It can also make identification difficult by obscuring any marking or colour coding.
Grit and dirt will pick up on the face of soiled webbing and can cause rapid wear and abrasion.
Where necessary they should be washed in clean water or in accordance with the
manufacturers instructions.
Assess any damaged eyes or terminal fittings. Cuts, abrasion and damage to the stitching
around folded eyes and local protection should be carefully assessed. Terminal fittings should
be checked for any damage such as cracks, bruising, or deformation. Particular attention
should be paid to the webbing where it passes around terminal fittings as this is a point of high
wear and cutting can occur from misuse.
Assess the surfaces for chafing. Some chafing is acceptable if this is confined to the surface
fibres.
Assess any abrasion. If the webbing shows signs of local abrasion, as opposed to general wear,
serious loss of strength may occur.
Assess any cuts. Both longitudinal and cross cuts into the surface of the webbing result in loss
of strength. Cross cuts on the edges of belt slings are particularly detrimental to the strength of
the sling.
Assess any areas affected by ultraviolet light, biological or chemical attack. Local weakening
and softening of the material may result which is often indicated by flaking of the surface
fibres.
Assess any heat and friction damage. The surface fibres take on a glazed appearance especially
where the fibres have melted and fused.
Assess any weld spatter burns. Textile slings are often used in welding processes as they
insulate the work piece from the lifting appliance. Weld spatter will cause localised burning
and will embed in the webbing causing internal abrasion.
Assess any damaged stitching. Damage to the stitching or looseness of the threads is cause for
concern.
Assess any loose webbing where the weft is soft and can be moved by hand.
The Safety Assessment Federation Ltd
Page 3 of 3
6. REJECTION
The fibre sling should be removed from service where:
The weave of the fibres has been disturbed and/or discontinued.
The outer sacrificial sheath has either a single severe transverse cut or multiple cuts in a
concentrated area of the sling, and where there is evidence of fibre withdrawal or abrasion.
There is evidence of fibre extrusion.
There are any visibly severed/fraying fibres.
