M54HC4017

M74HC4017
October 1992
DECADE COUNTER/DIVIDER
B1R
(Plastic Package)
ORDER CODES :
M54HC4017F1R M74HC4017M1R
M74HC4017B1R M74HC4017C1R
F1R
(Ceramic Package)
M1R
(Micro Package)
C1R
(Chip Carrier)
PIN CONNECTIONS(top view)
NC =
No Internal
Connection
Q3
DESCRIPTION
.HIGH SPEED
tPD = 21 ns (typ.) AT VCC = 5V
.LOWPOWER DISSIPATION
I
CC
= 4 A(MAX.) AT T
A
= 25
o
C
.HIGH NOISEIMMUNITY
VNIH = VNIL = 28 % VCC (MIN.)
.OUTPUT DRIVE CAPABILITY
10 LSTTL LOADS
.SYMMETRICAL OUTPUT IMPEDANCE
|IOH| = IOL = 4 mA (MIN.)
.BALANCEDPROPAGATION DELAYS
t
PLH
= t
PHL
.WIDE OPERATING VOLTAGE RANGE
VCC (OPR) = 2 V TO6 V
.PIN AND FUNCTION COMPATIBLEWITH
4017B
The M54/74HC4017 is a high speed CMOS DE-
CADE COUNTER/DIVIDER fabricated in silicon
gate C2MOS technology. It has the same high
speed performance of LSTTL combined with true
CMOS low power consumption.
The M54/74HC4017 is a 5-stage Johnson counter
with 10 decoded outputs. Each of the decoded out-
puts is normally low and sequentially goes high on
the lowtohigh transition of the clock input. Each out-
put stays high for one clock period of the 10 clock
period cycle. The CARRY output goes low to high
after OUTPUT 10 goes low, and can be used incon-
junction with the CLOCKENABLE to cascade sev-
eral stages.
The CLOCKENABLE input disables counting when
in the high state. A RESET input is also provided
which when taken high sets all the decoded outputs
low.
1/12
INPUT AND OUTPUT EQUIVALENT CIRCUIT
TRUTH TABLE
CLOCK CLOCK ENABLE CLEAR DECODE OUTPUT (H)
X X H QO
L X L Qn
X H L Qn
L L Qn + 1
L L Qn
H L Qn
H L Qn + 1
X: DONT CARE
Qn : NO CHANGE
LOGIC DIAGRAM
M54/M74HC4017
2/12
TIMING DIAGRAM
PIN DESCRIPTION
PIN No SYMBOL NAME AND FUNCTION
3, 2, 4, 7,
10, 1, 5, 6,
9, 11
Q0 to Q9 Decoded Outputs
12 C
OUT
Carry Output (Active
LOW)
13 CKEN Clock Enable Input
(Active LOW)
14 CLOCK Clock Input (LOW to
HIGH, Edge-triggered)
15 RESET Master Reset Input
(Active HIGH)
8 GND Ground (0V)
16 VCC Positive Supply Voltage
IEC LOGIC SYMBOL
M54/ M74HC4017
3/12
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
VCC Supply Voltage -0.5 to +7 V
V
I
DC Input Voltage -0.5 to V
CC
+ 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
IIK DC Input Diode Current 20 mA
I
OK
DC Output Diode Current 20 mA
IO DC Output Source Sink Current Per Output Pin 25 mA
ICC or IGND DC VCC or Ground Current 50 mA
P
D
Power Dissipation 500 (*) mW
Tstg Storage Temperature -65 to +150
o
C
T
L
Lead Temperature (10 sec) 300
o
C
AbsoluteMaximumRatingsare those values beyond whichdamage tothedevice may occur. Functional operation under these conditionisnot implied.
(*) 500 mW: 65
o
C derate to 300 mWby 10mW/
o
C: 65
o
C to85
o
C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Value Unit
V
CC
Supply Voltage 2 to 6 V
V
I
Input Voltage 0 to V
CC
V
VO Output Voltage 0 to VCC V
T
op
Operating Temperature: M54HC Series
M74HC Series
-55 to +125
-40 to +85
o
C
o
C
t
r
, t
f
Input Rise and Fall Time V
CC
= 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
VCC = 6 V 0 to 400
M54/M74HC4017
4/12
DC SPECIFICATIONS
Symbol Parameter
Test Conditions Value
Unit
VCC
(V)
TA = 25
o
C
54HC and 74HC
-40 to 85
o
C
74HC
-55 to 125
o
C
54HC
Min. Typ. Max. Min. Max. Min. Max.
V
IH
High Level Input
Voltage
2.0 1.5 1.5 1.5
V
4.5 3.15 3.15 3.15
6.0 4.2 4.2 4.2
V
IL
Low Level Input
Voltage
2.0 0.5 0.5 0.5
V
4.5 1.35 1.35 1.35
6.0 1.8 1.8 1.8
VOH High Level
Output Voltage
2.0
VI =
V
IH
or
V
IL
I
O
=-20 A
1.9 2.0 1.9 1.9
V
4.5 4.4 4.5 4.4 4.4
6.0 5.9 6.0 5.9 5.9
4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60
V
OL
Low Level Output
Voltage
2.0
V
I
=
V
IH
or
VIL
I
O
= 20 A
0.0 0.1 0.1 0.1
V
4.5 0.0 0.1 0.1 0.1
6.0 0.0 0.1 0.1 0.1
4.5 I
O
= 4.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 5.2 mA 0.18 0.26 0.33 0.40
II Input Leakage
Current
6.0
VI = VCC or GND 0.1 1 1 A
I
CC
Quiescent Supply
Current
6.0 V
I
= V
CC
or GND 4 40 80 A
M54/ M74HC4017
5/12
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Symbol Parameter
Test Conditions Value
Unit
VCC
(V)
TA = 25
o
C
54HC and 74HC
-40 to 85
o
C
74HC
-55 to 125
o
C
54HC
Min. Typ. Max. Min. Max. Min. Max.
t
TLH
t
THL
Output Transition
Time
2.0 30 75 95 110
ns
4.5 8 15 19 22
6.0 7 13 16 19
t
PLH
t
PHL
Propagation
Delay Time (CK,
CE - Q, C
OUT
)
2.0 100 195 245 295
ns
4.5 25 39 49 59
6.0 21 33 42 50
tPLH
t
PHL
Propagation
Delay Time
(CLEAR- Q, C
OUT
)
2.0 100 195 245 295
ns
4.5 25 39 49 59
6.0 21 33 42 50
fMAX Maximum Clock
Frequency
2.0 5 10 4 3.4
ns
4.5 25 41 20 17
6.0 29 48 24 20
tW(H)
t
W(L)
Minimum Pulse
Width (CLOCK)
2.0 35 75 95 110
ns
4.5 7 15 19 22
6.0 6 13 16 19
tW(H) Minimum Pulse
Width (CLEAR)
2.0 35 75 95 110
ns
4.5 7 15 19 22
6.0 6 13 16 19
ts Minimum Set-up
Time
2.0 12 50 65 75
ns
4.5 3 10 13 15
6.0 3 9 11 13
th Minimum Hold
Time
2.0 32 75 95 110
ns
4.5 8 15 19 22
6.0 7 13 16 19
tREM Minimum
Removal Time
2.0 28 75 95 110
ns
4.5 7 15 19 22
6.0 6 13 16 19
CIN Input Capacitance 5 10 10 10 pF
C
PD
(*) Power Dissipation
Capacitance
41
pF
(*) CPD isdefined as the value of the ICs internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the followingequation. ICC(opr) = CPD VCC fIN + ICC
M54/M74HC4017
6/12
TEST CIRCUIT I
CC
(Opr.)
SWITCHING CHARACTERISTICS TEST WAVEFORM
INPUT WAVEFORMIS THE SAMEAS THAT IN CASE OF SWITCHINGCHARACTERISTICS TEST.
M54/ M74HC4017
7/12
Plastic DIP16 (0.25) MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
a1 0.51 0.020
B 0.77 1.65 0.030 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 17.78 0.700
F 7.1 0.280
I 5.1 0.201
L 3.3 0.130
Z 1.27 0.050
P001C
M54/M74HC4017
8/12
Ceramic DIP16/1 MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 20 0.787
B 7 0.276
D 3.3 0.130
E 0.38 0.015
e3 17.78 0.700
F 2.29 2.79 0.090 0.110
G 0.4 0.55 0.016 0.022
H 1.17 1.52 0.046 0.060
L 0.22 0.31 0.009 0.012
M 0.51 1.27 0.020 0.050
N 10.3 0.406
P 7.8 8.05 0.307 0.317
Q 5.08 0.200
P053D
M54/ M74HC4017
9/12
SO16 (Narrow) MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45 (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8 (max.)
P013H
M54/M74HC4017
10/12
PLCC20 MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 9.78 10.03 0.385 0.395
B 8.89 9.04 0.350 0.356
D 4.2 4.57 0.165 0.180
d1 2.54 0.100
d2 0.56 0.022
E 7.37 8.38 0.290 0.330
e 1.27 0.050
e3 5.08 0.200
F 0.38 0.015
G 0.101 0.004
M 1.27 0.050
M1 1.14 0.045
P027A
M54/ M74HC4017
11/12
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specificationsmentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronicsproductsare not authorized for use ascritical componentsin life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
M54/M74HC4017
12/12