Technical Data Sheet
Approved
18400;18360
18400
epoxy
^(ValidationDate).
Penguard Pro
Product description
This is a two component amine cured epoxy coating. It is a surface tolerant, high solids, high build product.
Specially designed as a universal, all round, new construction coating. Can be used as primer, mid coat, finish
coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon
steel, stainless steel, aluminium, galvanised steel and thermally sprayed zinc substrates.
Typical use
Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed.
Recommended for offshore environments, including splash zones, refineries, power plants, bridges, buildings
and mining equipment. Specially designed as a universal product in coating systems where extended durability
is required. The product provides great flexibility in choice of dry film thickness range as well as area of use.
Other
Approvals and certificates
Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in
offshore environment, below 120 C.
Additional certificates and approvals may be available on request.
Other variants available
Penguard
Penguard
Penguard
Penguard
Pro
Pro
Pro
Pro
Alu
Alu X
GF
GF X
Refer to separate TDS for each variant.
Colours
selected range of colours
Product data
Property
Test/Standard
Solids by volume
Gloss level (60 )
ISO 3233
ISO 2813
Flash point
Specific gravity
VOC-USA / VOC-Hong Kong
ISO 3679 Method 1
calculated
EPA Method 24
VOC-Solvent Emission Directive
SED (1999/13/EC)
Description
75 2 %
semi gloss (35-70)
32 C
1,37 kg/l
240 g/l
168 g/kg
The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss level: According to Jotun Performance Coatings' definition.
Recommended film thickness per coat
Date of issue:
6 March 2015
Page: 1/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Pro
Film thickness and
spreading rate
Dry film thickness
(m)
(m)
Theoretical
spreading rate
(m/l)
Minimum
100
133
7,5
Maximum
Typical
500
150
667
200
1,5
5
Wet film thickness
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Surface preparation summary table
Surface preparation
Substrate
Minimum
Recommended
Carbon steel
St 2 (ISO 8501-1)
Sa 2 (ISO 8501-1)
Stainless steel
The surface shall be hand or machine
abraded with non-metallic abrasives
or bonded fibre machine or hand
abrasive pads to impart a scratch
pattern to the surface and to remove
all polish from the surface.
Cleanliness and surface profile
corresponding to Sa 2, Fine G (ISO
8503-2)
Aluminium
The surface shall be hand or machine
abraded with non-metallic abrasives
or bonded fibre machine or hand
abrasive pads to impart a scratch
pattern to the surface and to remove
all polish from the surface.
Cleanliness corresponding to
description of Sa 1 (ISO 8501-1)
Galvanised steel
The surface shall be clean, dry and
appear with a rough and dull profile.
Light brush blasting using nonmetallic abrasive leaving a clean,
rough and even pattern.
Shop primed steel
Dry, clean and intact shop primer.
Abrasive swept or alternatively
blasted to Sa 2 (ISO 8501-1) of at
least 70 % of the surface.
Coated surfaces
Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1)
Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1)
Application
Application methods
The product can be applied by
Spray:
Use airless spray.
Brush:
Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Roller:
May be used for small areas. Not recommended for first primer coat. Care must be taken
to achieve the specified dry film thickness.
Date of issue:
6 March 2015
Page: 2/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Pro
Product mixing ratio (by volume)
Penguard Pro Comp A
Penguard Pro Comp B
3 part(s)
1 part(s)
Thinner/Cleaning solvent
Thinner:
Jotun Thinner No. 17
Guiding data for airless spray
Nozzle tip (inch/1000):
19-27
Pressure at nozzle (minimum):
150 bar/2100 psi
Drying and Curing time
Substrate temperature
0 C
5 C
10 C
15 C
23 C
40 C
Surface (touch) dry
Walk-on-dry
Dry to over coat, minimum
Dried to over coat, maximum, atmospheric
Dried/cured for service
18
32
16
14
8h
18 h
12 h
14 d
6h
12 h
7h
14 d
12 d
5h
10 h
5h
14 d
12 d
3h
6h
3h
14 d
10 d
1h
4h
2h
10 d
7d
h
h
h
d
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and at
the typical DFT for the product.
This product may be applied at substrate temperatures down to -5 C depending on other influencing factors,
including but not limited to thinning, ventilation etc. Care should be taken when over coating at low
temperatures as the full system will require higher temperatures to reach full cure and proper mechanical
strength.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.
Dried to over coat, maximum, atmospheric: The longest time allowed before the next coat can be applied
without any surface preparation.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Date of issue:
6 March 2015
Page: 3/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Pro
Induction time and Pot life
Paint temperature
23 C
Induction time
Pot life
10 min
1h
Heat resistance
Temperature
Continuous
Dry, atmospheric
120 C
Peak
140 C
Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat:
epoxy, epoxy mastic, zinc epoxy, zinc silicate
Subsequent coat:
acrylic, epoxy, polyurethane, polysiloxane
Packaging (typical)
Penguard Pro Comp A
Penguard Pro Comp B
Volume
(litres)
Size of containers
(litres)
15
5
20
5
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Shelf life at 23 C
Penguard Pro Comp A
12 month(s)
Penguard Pro Comp B
24 month(s)
Date of issue:
6 March 2015
Page: 4/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Pro
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
Products primarily meant for use as primers and antifoulings may have slight color variations from batch to
batch. Such products may fade and chalk when exposed to sunlight and weathering.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue:
6 March 2015
Page: 5/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
