PRODUCT SPECIFICATION SHEET
BELZONA 7111
FN10171
GENERAL INFORMATION
Product Description:
Cost-effective, two-component, 100% solids compound designed for use as a chocking or grouting material to endure the physical and thermal shock common to
marine and industrial environments. Exhibits excellent non-shrinking property, high impact and compressive strength.
Application Areas:
When mixed and applied as detailed in the Belzona Instructions for Use (IFU), the system is ideally suited for application to the following:
-
Diesel Engines
Gas engines
Pumps
Generators
Compressors
Reduction Gears
Bearing Blocks
Crane rails
Other machinery
APPLICATION INFORMATION
Application Methods
Casting by pouring
Application Temperature
Application should ideally occur in the following ambient temperature range:
55F/13C to 95F/35C
Volume Capacity
Belzona 7111 should be applied as a chocking or grouting compound in
depths of in to 4 in (12 mm to 100 mm).
The theoretical volume capacity will be 266 in (4360 cm) /6.95 kg unit.
Cure Time
Cure times will vary depending on the ambient conditions.
Temperature
60F/15C
68F/20C
86F/30C
Mixed Properties
Color:
Density:
Gel Time (BS 5350-B5):
Orange, Grey
1.51 g/cm
45 minutes (68F/20C)
Mixing Ratio by Weight (base : solidifier)
14.5 : 1
Refer to 7111 IFU (Section 5 Solidifier Ratio Guide) for thickness greater than
1 (38 mm) and when the steel surface temperature is above 77F (25C).
Working Life
The working life will vary according to the temperature. At 77F/25C, the usable
life of mixed material will typically be 30 minutes, consult the Belzona IFU for
specific details.
Cure Times
48 hours
24 hours
12 hours
The above application information serves as introductory guide only. For full application details including the recommended a pplication procedure/technique, refer to
the Belzona IFU which is enclosed with each packaged product.
Belzona 7111 - Product Specification Sheet
www.belzona.com
Printed in the USA
Publication No. 05-01-14-04
Page 1 of 3
PRODUCT SPECIFICATION SHEET
BELZONA 7111
FN10171
COMPRESSIVE PROPERTIES
HARDNESS
When determined in accordance with ASTM D695, typical values will be:
The Shore D and Barcol hardness, when determined in accordance with
ASTM D2240, ASTM D2583 respectively, will typically be:
Compressive Yield Strength
14930 psi / 102.9 MPa
Compressive Modulus
5.75 x105 psi / 3964 MPa
(68F/20C cure & 68F/20C test)
(68F/20C cure & 68F/20C test)
TENSILE PROPERTIES
Barcol
89.5
37
IMPACT RESISTANCE
When determined in accordance with ASTM D638, typical values will be:
Tensile Strength
6410 psi / 44.2 MPa
68F/20C cure
Shore D
(68F/20C cure & 68F/20C test)
Izod Pendulum
Izod impact strength, when determined in accordance with ASTM D256, will
typically be:
Un-notched:
0.75 J/cm
(68F/20C cure & 68F/20C test)
FLEXURAL PROPERTIES
When determined in accordance with ASTM D790, typical values will be:
FIRE RESISTANCE
Flexural Strength
9580 psi / 66.1 MPa
(68F/20C cure & 68F/20C test)
Flexural Modulus
9.94x105 psi / 6853 MPa
(68F/20C cure & 68F/20C test)
When determined in accordance with ASTM D635:
Self-Extinguishing
SHEAR PROPERTIES
SHELF LIFE
When determined in accordance with ASTM D732, typical values will be:
Separate Base and Solidifier components will have a shelf life of 3 years
when stored in their original unopened containers between 32F/0C and
86F/30C
Shear Strength
6590 psi / 45.4 MPa
(68F/20C cure & 68F/20C test)
ADHESION
Tensile Shear
When tested in accordance with ASTM D1002, using metal substrates, grit
blasted to a 3-4 mil (75-100 micron) profile, typical values will be:
Mild steel
Stainless steel
3,570 psi (24.6 MPa)
2,900 psi (20.0 MPa)
Pull Off Adhesion
The PosiTest dolly pull off strength, as determined in accordance with ASTM
4541, will typically be:
Mild steel
Concrete*
*Cohesive failure of substrate
Belzona 7111 - Product Specification Sheet
3,880 psi (26.8 MPa)
980 psi (6.8 MPa)
www.belzona.com
Printed in the USA
Publication No. 05-01-14-04
Page 2 of 3
PRODUCT SPECIFICATION SHEET
BELZONA 7111
FN10171
WARRANTY
Belzona guarantees this product will meet the performance claims stated herein when material is stored and used as instructed in the Belzona Information For Use
leaflet. Belzona further guarantees that all its products are carefully manufactured to ensure the highest quality possible a nd tested strictly in accordance with
universally recognised standards (ASTM, ANSI, BS, DIN, ISO etc.). Since Belzona has no control over the use of the product described herein, no warranty for any
application can be given.
AVAILABILITY AND COST
MANUFACTURER
Belzona 7111 is available from a network of Belzona Distributors throughout
the world for prompt delivery to the application site. For information, consult
the Belzona Distributor in your area.
Belzona Polymerics Ltd.
Claro Road, Harrogate,
HG1 4DS, UK
Belzona Inc.
14300 N.W. 60th Ave,
Miami Lakes, FL, USA, 33014
HEALTH AND SAFETY
TECHNICAL SERVICE
Prior to using this material, please consult the relevant Material Safety Data
Sheets.
Complete technical assistance is available and includes fully trained
Technical Consultants, technical service personnel and fully staffed research,
development and quality control laboratories.
The technical data contained herein is based on the results of long term tests carried out in our laboratories and to the best of our knowledge
is true and accurate on the date of publication. It is however subject to change without prior notice and the user should contact Belzona to
verify the technical data is correct before specifying or ordering. No guarantee of accuracy is given or implied. We assume no responsibility for
rates of coverage, performance or injury resulting from use. Liability, if any, is limited to the replacement of products. No other warranty or
guarantee of any kind is made by Belzona, express or implied, whether statutory, by operation of law or otherwise, including merchantability or
fitness for a particular purpose.
ISO 9001:2008
US3429
Manufactured under an ISO 9000 Registered
Quality Management System
Nothing in the foregoing statement shall exclude or limit any liability of Belzona to the extent such liability cannot by law be excluded or limited.
Copyright 2014 Belzona International Limited. Belzona is a registered trademark.
Belzona 7111 - Product Specification Sheet
www.belzona.com
Belzona is a registered trademark
Printed in the USA
Publication No. 05-01-14-04
Page 3 of 3
