SCHEDULE OF RATES FOR
ELE CT R ICAL IN STA LLA TIO N
WORKS IN SARAWAK 2014
JKR Sarawak
December 2014
Notes to tenderers:
1.
This is only a cover page for this document. Please obtain the full set from the
JKR Sarawak webpage or any JKR Sarawak office.
2.
The Location Factor from base at Kuching City for this tender is ____ %
and is the percentage over all the items and rates as listed in this Schedule of
Rates to be used for the purposes as stated in the tender documents.
3.
Any attempt to amend / change / correct etc. this percentage by the
tenderer shall cause the tender to be disqualified.
L O C AT I O N F AC T O R FR O M B A S E AT K U CH I N G CI T Y
(To be read together with the Rules of determining the Location Factor)
Kuching
Samarahan
Betong
Kapit
City
0%
Padawan
District
15%
2%
Lubok Antu
20%
Santubong
3%
Lingga
20%
Siburan
3%
Pantu
13%
Bau
5%
Engkilili
18%
Lundu
8%
Sematan
9%
Skrang
15%
District
2%
District
12%
Serian
5%
Kem Bt 10 & 14
13%
Simunjan
12%
Durin
15%
Sebuyau
15%
Bawang Assan
13%
Asajaya
10%
Sungai Assan
13%
Sadong Jaya
12%
Kanowit
16%
Tebedu
8%
Machan
16%
Tebakang
8%
Nibong Tada
15%
Balai Ringin
8%
Nanga Tada
17%
Nanga Dap
20%
Nanga Ngemah
20%
Sri Aman
Sibu
District
20%
Nanga Ngungun
20%
Spaoh
20%
Nanga Poi
22%
Debak
20%
Nanga Jagau
40%
Pusa
21%
Selangau
18%
Beladin
20%
Ulu Balingian
20%
Maludam
22%
Arip
22%
Saratok
20%
Stapang
16%
Roban
20%
Rassau
22%
Kabong
20%
District
30%
District
15%
Song
25%
Tatau
20%
Belaga
70%
Sebauh
23%
Sungai Asap
25%
Bintulu
L O C AT I O N F AC T O R FR O M B A S E AT K U CH I N G CI T Y
(To be read together with the Rules of determining the Location Factor)
Mukah
Sarikei
District
20%
City
15%
Dalat
20%
Subis
15%
Oya
20%
Bekenu
15%
Igan
18%
Marudi
25%
Balingian
23%
Long Lama
40%
Kuala Balingian
23%
Beluru
22%
Semop
30%
Matu
25%
District
30%
Betanak
30%
Lawas
28%
Daro
25%
Bruit
30%
Tanjung Manis
18%
District
18%
Bintangor
18%
Pakan
20%
Selalang
20%
Julau
20%
Meluan
22%
Ulu Entabai
23%
Engkamop
30%
Nanga Wak
15%
Nanga Entabai
14%
Miri
Limbang
R U L E S O F DE T E R MI NI NG T H E L O C AT I O N FA C T O R
1.
The % factors as stated are for those projects accessible by motorized vehicles within
15km radius from the location shown.
2.
Where the project site is beyond 15km radius of the above stated locations, these
additional % factors shall be added on to those percentages stated above:
% addition
(i)
( ii )
( iii )
( iv )
(v)
3.
> 15km
> 45km
> 90km
> 135km
> 180km
< 45km
< 90km
< 135km
< 180km
< 220km
5%
10%
15%
20%
25%
Where the project sites are accessible only by waterway
(i)
( ii )
( iii )
( iv )
(v)
( vi )
areas within 15 km radius
areas within 30 km radius
areas within 60 km radius
areas within 90 km radius
areas within 120 km radius
areas within 150 km radius
0%
5%
10%
15%
20%
25%
4.
Where the project sites can only be accessible by air, the location factor shall be doubled
over the value obtained from that by motorized vehicles.
5.
Where the project sites can only be accessible by foot, the location factor shall be 50%
over the value obtained from that by authorized vehicles
6.
Where in determining the locations factor and two or more factors and radial distances
are equally applicable, the lower in each case shall be used.
7.
Where in determining the location factor and two or more factors and radial distances
by the rules above whereby there can be a combination due to accessibility, say partly
land and partly waterway or partly waterway and partly by foot, there shall be a
combination of the rules according to the radial distance from the nearest locations
stated above.
8.
Where in determining the location factor and the Site for the project lies within two
more radial distances, the addition % for the radial distance within which more than
50% of the Site lies shall be used.
P R E AM B L E S
1. All rates given shall include supply, delivery, installation, testing and
commissioning and shall include associated accessories and fitting.
2. Rate per point applies for the stated route length. For longer route length, the
rate per metre, derived from the rate per point shall be used.
3. All rates shall be used and read together with the Location Factor from base
at Kuching City.
4. All descriptions are to be read with reference to the Standard Electrical
Installation Specification (Latest Version) and the following :
a) All rates herein shall be held to include for supply and delivery to site, wastage on
materials, carriage and cartage, carrying in and return of empties, hoisting, setting,
fitting and fixing in position, making good and all other labours and everything else
necessary (including any custom duties, etc.) for the proper completion of each item and
for establishment charges and profit.
b) Rates for each item of paving shall be held to include for all rounded angles, arrises and
making good and any other sundry items of alike nature.
c) Rates for mild steel tubing are to include for short running lengths, sockets, backnuts,
elbows and bends.
SOR for Electrical Installation Works 2014
GENERAL WIRING
Item
No.
Description
Unit
Rate (RM)
Concealed conduit wiring c/w metal clad switch and socket plates
and accessories : Wiring shall be run concealed, in Class B
galvanized steel conduits and complete with GS conduit boxes let
into cement or timber wall, or partition, together with all necessary
metal clad lighting switch plates, switched socket plates, isolators
and accessories. Wiring shall be 1.5 mm2 PVC for fan and lighting
2
points, 2.5 mm PVC for 13A and 15A switched sockets. 13A 3-pin
switched socket points shall be wired in ring circuit/s. Accepted
brands Clipsal, PDL or MEM.
1
Lighting Point wired from nearest switch : Rate per point applies up to
route length of 10 metres.
(i)
6A 1-way lighting point c/w switch.
Per point
102.20
(ii)
6A 2-way lighting point c/w switch.
Per point
139.90
(iii)
6A intermediate lighting point c/w switch.
Per point
161.40
Per point
53.80
Lighting Point wired from nearest lighting point (sharing same switch) up
to 4 metre route length.
(i)
6A 1-way lighting point.
Fan Points : wired from nearest switch (up to 10 metres route length).
(i)
Ceiling fan point c/w 6A switch.
Per fan point
102.20
(ii)
Extractor fan point c/w 6A switch. Cost excludes hard-wood frame and
opening for fan.
Per fan point
102.20
Switched Socket Outlets :
(i)
13A 3-pin switched socket point in ring circuit :
1 gang (up to 10 metre route length).
Per 1-gang
socket pt.
139.90
(ii)
13A 3-pin switched socket point in ring circuit :
2 gang (up to 10 metre route length).
Per 2-gang
socket pt.
188.30
15A 3-pin switched socket point (up to 15 metre route length).
Per point
236.70
(iii)
Per point
269.00
Per isolator
312.00
Isolators and Water Heater Points : (up to 15 metre route length).
(i)
Water heater point c/w 20A double pole switch with neon light indicator,
2
4mm PVC cable.
(ii)
20A single phase isolator point 4 mm cabling.
(iii)
30A single phase isolator point 6 mm cabling.
Per isolator
430.40
(iv)
20A TPN isolator point 4 mm cabling.
Per isolator
451.90
(v)
30A TPN isolator point 6 mm cabling.
Per isolator
613.30
SOR ELEC 2014/Page 1 of 10
'
GENERAL WIRING...(CONT D)
Item
No.
Description
Unit
Rate (RM)
TV / Telephone Point : (up to 15 metre route length).
(i)
1 pair c/w socket and 2 x 0.63 mm cable.
Per point
96.90
(ii)
2 pairs c/w socket and 4 x 0.63 mm cable.
Per point
118.40
(iii)
TV antennae point c/w 5c / 2v cable and TV socket.
Per point
96.90
Miscellaneous Wiring Point : (up to 15 metre route length).
(i)
Single phase power supply to fire protection control panel 2.5 mm PVC
cabling.
(ii)
Lighting point for emergency lighting or keluar sign c/w 1.5 mm cable.
Per point
231.30
Per point
96.90
Surface conduit wiring c/w metal clad switch and socket plates and
accessories : Wiring shall be run on surface, in Class B galvanized
steel conduits and complete with GS conduit boxes, together with all
necessary metal clad lighting switch plates, switched socket plates,
isolators and accessories. Wiring shall be 1.5 mm PVC for fan and
lighting points, 2.5 mm PVC for 13A and 15A switched sockets. 13A
3-pin switched socket points shall be wired in ring circuit/s.
Accepted brands Clipsal, PDL or MEM.
8
Lighting Point wired from nearest switch : Rate per point applies up to
route length of 10 metres.
(i)
6A 1-way lighting point c/w switch.
Per point
91.50
(ii)
6A 2-way lighting point c/w switch.
Per point
134.50
(iii)
6A intermediate lighting point c/w switch.
Per point
150.70
Lighting Point wired from nearest lighting point (sharing same switch)
Per point
48.50
up to 4 metre route length.
(i)
6A 1-way lighting point.
10
Fan Points : wired from nearest switch (up to 10 metres route length) .
(i)
Ceiling fan point c/w 6A switch.
Per fan point
91.50
(ii)
Extractor fan point c/w 6A switch. Cost excludes hard-wood frame and
opening for fan.
Per fan point
91.50
11
Switched Socket Outlets :
(i)
13A 3-pin switched socket point in ring circuit :
1 gang (up to 10 metre route length).
Per 1-gang
socket pt.
(ii)
13A 3-pin switched socket point in ring circuit :
2 gang (up to 10 metre route length).
Per 2-gang
socket pt.
SOR ELEC 2014/Page 2 of 10
139.90
182.90
'
GENERAL WIRING...(CONT D)
Item
No.
Description
Unit
Rate (RM)
Per point
193.70
'
11
Switched Socket Outlets : (Cont d)
(iii)
15A 3-pin switched socket point (up to 15 metre route length).
12
Isolators and Water Heater Points : (up to 15 metre route length).
(i)
Water heater point c/w 20A double pole switch with neon light indicator,
4mm PVC cable.
(ii)
20A single phase isolator point 4 mm cabling.
(iii)
30A single phase isolator point 6 mm cabling.
Per point
258.20
Per isolator
290.50
Per isolator
392.70
(iv)
20A TPN isolator point 4 mm cabling.
Per isolator
387.30
(v)
30A TPN isolator point 6 mm cabling.
Per isolator
548.70
13
TV / Telephone Point : (up to 15 metre route length).
(i)
1 pair c/w socket and 2 x 0.63 mm cable.
(ii)
Per point
86.10
2 pairs c/w socket and 4 x 0.63 mm cable.
Per point
107.60
(iii)
TV antennae point c/w 5c / 2v cable and TV socket.
Per point
86.10
14
Miscellaneous Wiring Point : (up to 15 metre route length).
(i)
Single phase power supply to fire protection control panel 2.5 mm PVC
cabling.
(ii)
Lighting point for emergency lighting or keluar sign c/w 1.5 mm cable.
Per point
Per point
215.20
86.10
Surface Wiring : Wiring shall be run surface on batten wood
complete with all necessary PVC moulded conduit boxes, lighting
switch plates, 13A or 15A switched socket plates and accessories.
2
2
Wiring shall be 1.5 mm PVC/PVC for fan and lighting points, 2.5 mm
PVC/PVC for 13A and 15A switched sockets. 13A 3-pin switched
socket points shall be wired in ring circuit/s. Accepted brands
Clipsal, PDL or MEM.
15
Lighting Point wired from nearest switch : Rate per point applies up to
route length of 10 metres.
80.70
(i)
6A 1-way lighting point c/w switch.
Per point
(ii)
6A 2-way lighting point c/w switch.
Per point
118.40
(iii)
6A intermediate lighting point c/w switch.
Per point
139.90
16
Lighting Point wired from nearest lighting point (sharing same switch) up
to 4 metre route length.
(i)
Per point
6A 1-way lighting point.
SOR ELEC 2014/Page 3 of 10
48.50
'
GENERAL WIRING...(CONT D)
Description
Item
No.
Unit
Rate (RM)
17
Fan Points : wired from nearest switch (up to 10 metres route length).
(i)
Ceiling fan point c/w 6A switch, ceiling rose and hardwood block for fan
speed regulator.
Per fan point
80.70
Extractor fan point c/w 6A switch. (cost excludes hardwood frame and
opening for fan).
Per fan point
80.70
(ii)
18
Switched Socket Outlets and Water Heater Point :
(i)
13A 3-pin switched socket point in ring circuit :
1 gang (up to 10 metre route length).
Per 1-gang
socket pt.
118.40
(ii)
13A 3-pin switched socket point in ring circuit :
2 gang (up to 10 metre route length).
Per 2-gang
socket pt.
161.40
(iii)
15A 3-pin switched socket point (up to 15 metre route length).
Per point
(iv)
Water heater point c/w 20A double pole switch with neon light indicator, 4
mm PVC cable (up to 15 metre route length).
Per point
226.00
Per metre
32.30
Per metre
43.10
Per metre
53.80
Per metre
75.40
Per point
96.90
19
161.40
Mains and Sub-mains Wiring : from SESCo supply intake to distribution
boards/consumer units, through meter and cut-outs, using surface wiring.
2
(i)
1-phase 2 x 16 mm 1 core PVC insulated and sheathed cables.
(ii)
1-phase 2 x 25 mm 1 core PVC insulated and sheathed cables.
(iii)
3-phase 4 x 16 mm 1 core PVC insulated and sheathed cables.
(iv)
3-phase 4 x 25 mm 1 core PVC insulated and sheathed cables.
Concealed conduit wiring c/w plastic moulded switch and socket
plates and accessories : Wiring shall be run concealed, in Class B
galvanized steel conduits and complete with GS conduit boxes let
into cement or timber wall, or partition, together with all necessary
PVC moulded lighting switch plates, switched socket plates and
accessories. Wiring shall be 1.5 mm PVC for fan and lighting points,
2.5 mm PVC for 13A and 15A switched sockets. 13A 3-pin switched
socket points shall be wired in ring circuit/s. Accepted brands
Clipsal, PDL or MEM.
20
Lighting Point wired from nearest switch : Rate per point applies up to
route length of 10 metres.
(i)
6A 1-way lighting point c/w switch.
(ii)
6A 2-way lighting point c/w switch.
Per point
134.50
(iii)
6A intermediate lighting point c/w switch.
Per point
150.70
SOR ELEC 2014/Page 4 of 10
'
GENERAL WIRING...(CONT D)
Item
No.
Description
21
Lighting Point wired from nearest lighting point (sharing same switch) up
Unit
Rate (RM)
Per point
48.50
to 4 metre route length.
(i)
6A 1-way lighting point.
22
Fan Points : wired from nearest switch (up to 10 metres route length).
(i)
Ceiling fan point c/w 6A switch.
Per fan point
96.90
(ii)
Extractor fan point c/w 6A switch. Cost excludes hard-wood frame and
opening for fan.
Per fan point
96.90
23
Switched Socket Outlets :
(i)
13A 3-pin switched socket point in ring circuit :
1 gang (up to 10 metre route length).
Per 1-gang
socket pt.
129.10
(ii)
13A 3-pin switched socket point in ring circuit :
2 gang (up to 10 metre route length).
Per 2-gang
socket pt.
172.20
15A 3-pin switched socket point (up to 15 metre route length).
Per point
226.00
(iii)
24
TV / Telephone Point : (up to 15 metre route length).
(i)
1 pair c/w socket and 2 x 0.63 mm cable.
Per point
86.10
(ii)
2 pairs c/w socket and 4 x 0.63 mm cable.
Per point
107.60
(iii)
TV antennae point c/w 5c / 2v cable and TV socket.
Per point
86.10
25
Earthing Leads : from distribution board to earth electrode-green PVC
insulated copper cable protected by class 'B' galvanized steel conduits to
be installed below surface of hard-standing, cement floor, corridor, apron,
etc. (up to 10 metres route length)
(i)
16mm PVC insulated
(ii)
25mm PVC insulated
Per lot
Per lot
SOR ELEC 2014/Page 5 of 10
269.00
344.30
LIGHTING FITTINGS, FANS AND ACCESSORIES
Item
No.
Description
Unit
Rate (RM)
Accessories : Cost for extractor fan hole openings in brick or
wooden walls shall include cost of making the hole together with
2 x 4 hardwood frame. Size of opening shall be appropriate for the
diameter of fans indicated.
1
Installation of fan hook from cement floor slab.
Per unit
34.50
Installation of fan hook from timber floor joist.
Per unit
28.00
Extractor fan hole opening in brick wall for extractor fan of diameter from
400 to 500 mm (16 to 20).
Per no.
209.80
Extractor fan hole opening in brick wall for extractor fan of diameter from
200 to 350 mm (8 to 14).
Per no.
172.20
Extractor fan hole opening in wooden wall for extractor fan of diameter
from 400 to 500 mm (16 to 20).
Per no.
142.10
Extractor fan hole opening in wooden wall for extractor fan of diameter
from 200 to 350 mm (8 to 14).
Per no.
123.80
Extractor fan hole opening in glass panel for extractor fan of diameter from
200 to 350 mm (8 to 14).
Per no.
158.20
Fans : Cost includes supply and installation of fittings. Ceiling fans
and oscillating fans shall have individual 3-speed (low/medium/high)
regulators. Wall fans shall feature pull cord oscillation control and 3speed (low/medium/high) regulators. Ceiling fans shall have safety
steel suspension wire and safe power disconnection feature. Cost of
making fan hole opening is priced separately. Acceptable brands
Khind, National, KDK or Sanyo
8
Ceiling fan 1,520 mm (60) diameter sweep.
Per unit
Ceiling mount oscillating fan 500 mm (20) dia.
Per unit
349.70
10
Ceiling mount oscillating fan 400 mm (16) dia.
Per unit
279.80
11
Wall mount fan 500 mm (20) diameter.
Per unit
279.80
12
Wall mount fan 400 mm (16) diameter.
Per unit
247.50
13
Extractor fan 500 mm (20) diameter.
Per unit
279.80
14
Extractor fan 400 mm (16) diameter.
Per unit
236.70
15
Extractor fan 350 mm (14) diameter.
Per unit
204.40
16
Extractor fan 300 mm (12) diameter.
Per unit
182.90
17
Extractor fan 200 mm (8) diameter.
Per unit
158.20
SOR ELECT 2014/Page 6 of 10
175.40
'
LIGHTING FITTINGS, FANS AND ACCESSORIES...(CONT D)
Item
No.
Description
Unit
Rate (RM)
Fluorescent Fittings : All fluorescent fittings shall be complete with
low loss polyester resin impregnated ballasts of loss not exceeding
6.5 watts, power factor correction capacitor to correct to power
factor of not less than 0.85, starter, fluorescent tubes and holders.
Cost includes supply and installation. Acceptable brands - LHL,
Britelite, Davis, Jetlite, National, GEC, Philip, Thorn.
18
Channel Fluorescent Fitting 1 x 18W / 36 W Surface Mount
(i)
1 x 18 watt bare channel fluorescent fitting.
Per unit
33.40
(ii)
1 x 18 watt channel fluorescent fitting c/w wire guard.
Per unit
61.40
(iii)
1 x 36 watt bare channel fluorescent fitting.
Per unit
38.80
(iv)
1 x 36 watt bare channel fluorescent fitting c/w metal angle reflector.
Per unit
73.20
(v)
1 x 36 watt bare channel fluorescent fitting c/w suspension rod.
Per unit
78.60
(vi)
1 x 36 watt channel fluorescent fitting c/w wire guard.
Per unit
67.80
(vii)
1 x 36 watt channel fluorescent fitting c/w wire guard and suspension rod.
Per unit
96.90
19
Channel Fluorescent Fitting 2 x 36 W Surface Mount
(i)
2 x 36 watt bare channel fluorescent fitting.
Per unit
67.80
(ii)
2 x 36 watt bare channel fluorescent fitting c/w suspension rod.
Per unit
90.40
(iii)
2 x 36 watt channel fluorescent fitting c/w diakon diffuser.
Per unit
101.20
(iv)
2 x 36 watt channel fluorescent fitting c/w diakon diffuser and suspension
rod.
Per unit
123.80
(v)
2 x 36 watt bare channel fluorescent fitting c/w metal trough reflectors.
Per unit
95.80
(vi)
2 x 36 watt bare channel fluorescent fitting c/w metal trough reflectors and
suspension rod.
Per unit
129.10
20
Modular type Fluorescent Fittings Recessed Fittings
(i)
2 x 18 watt modular recessed (2 x 2) fluorescent fitting c/w aluminum
parabolic reflector and baffles.
Per unit
158.20
2 x 36 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and baffles.
Per unit
191.50
3 x 36 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and louvers.
Per unit
231.30
(ii)
(iii)
SOR ELECT 2014/Page 7 of 10
'
LIGHTING FITTINGS, FANS AND ACCESSORIES...(CONT D)
Item
No.
Description
Unit
Rate (RM)
158.20
21
Modular type Fluorescent Fittings Surface Fittings
(i)
2 x 18 watt modular recessed (2 x 2) fluorescent fitting c/w aluminum
parabolic reflector and baffles.
Per unit
2 x 36 watt modular surface (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and baffles.
Per unit
3 x 36 watt modular surface (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and louvers.
Per unit
219.50
Per unit
328.20
Per unit
406.70
Per unit
327.10
Per unit
406.70
(ii)
(iii)
22
Self-contained Modular type Fluorescent Fittings c/w Battery & Charger
(i)
2 x 18 watt modular recessed (2 x 2) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit.
2 x 36 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit.
(ii)
2 x 18 watt modular surface (2 x 2) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit.
2 x 18 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit.
(iii)
(iv)
191.50
Miscellaneous Lighting Fittings : Cost includes supply and
installation of fittings. Installation for floodlight fittings are in
reference to standard installation on walls accessible by ladder.
Accepted brands for flood lights Nikkon, Thorn or Philips.
Emergency Light / KELUAR Sign Fittings : self contained c/w sealed 3-hr
23
maintenance free sealed lead-acid battery, charger and control unit c/w
trickle charging & over-charge protection.
(i)
(ii)
(iii)
Self contained 2 x 8 watts emergency lighting fitting.
KELUAR sign fluorescent type, single sided.
KELUAR sign fluorescent type, double sided.
(iv) KELUAR c/w direction signage single sided fluorescent type.
(v)
KELUAR c/w direction signage double sided fluorescent type.
(vi) KELUAR sign LED type, single sided.
(vii) KELUAR sign LED type, double sided.
(viii) KELUAR c/w direction signage single sided LED type.
(ix) KELUAR c/w direction signage double sided LED type.
SOR ELECT 2014/Page 8 of 10
123.80
Per unit
Per unit
180.80
Per unit
224.00
Per unit
186.20
Per unit
236.70
Per unit
186.20
Per unit
196.90
Per unit
203.40
Per unit
215.20
'
LIGHTING FITTINGS, FANS AND ACCESSORIES...(CONT D)
Item
No.
Description
24
Lamp-shade c/w incandescent lamp
(i)
Coolicon lamp shade, lamp holder c/w 40W, 60W or 100 W incandescent
lamp.
Unit
Rate (RM)
Per fitting
17.30
67.80
25
Flood-light / Spot-light Fittings
(i)
Outdoor type spot light fitting c/w metal lamp holder and PAR 38 150 W
lamp of various colours.
Per fitting
Outdoor type metal halide floodlight fittings c/w 400 W lamp, control gear
and power factor correction capacitor.
Per fitting
Outdoor type metal halide floodlight fittings c/w 250 W lamp, control gear
and power factor correction capacitor.
Per fitting
451.90
Outdoor type high pressure sodium floodlight fittings c/w 400 W lamp,
control gear and power factor correction capacitor.
Per fitting
542.20
Outdoor type high pressure sodium floodlight fittings c/w 250 W lamp,
control gear and power factor correction capacitor.
Per fitting
462.60
Per fitting
90.40
Per fitting
45.20
(ii)
(iii)
(iv)
(v)
26
Bulkhead Fittings
(i)
Bulkhead fitting pressure die-cast aluminium alloy type c/w 40W, 60W or
100W incandescent lamp, glass cover and wire guard.
(ii)
Bulkhead fitting plastic die-cast type c/w 40W, 60W or 100W
incandescent lamp, plastic cover and wire guard.
SOR ELECT 2014/Page 9 of 10
519.70
DISTRIBUTION BOARDS & CONSUMER UNITS
Item
No.
Description
Unit
Rate (RM)
Distribution Boards & Consumer Units : Distribution boards and
consumer units shall be metal clad type c/w isolator, residual current
circuit breaker (RCCB) and assortment of miniature circuit breakers
(mcb). Isolators and RCCB shall be double pole and four pole
respectively for single phase and three phase units. Isolators shall be
rated at 60A min. Miniature circuit breakers shall be single pole 6A,
15A, or 32A as required, of minimum breaking capacity 5 kA, and
tripping curve Type B. Comb-type busbars are not accepted. Units
shall feature DIN rail mounting, for plug-in, wired-out mcb. Accepted
brands MEM, Hager, L&T, LKH
1
Single Phase Consumer Units
(i)
4 way ( RCCB : 40A, 100 mA sensitivity).
Per set
290.50
(ii)
4 way ( RCCB : 60A, 100 mA sensitivity).
Per set
338.90
(iii)
6 way ( RCCB : 40A, 100 mA sensitivity).
Per set
371.20
(iv)
6 way ( RCCB : 60A, 100 mA sensitivity).
Per set
441.10
(v)
8 way ( RCCB : 40A, 100 mA sensitivity).
Per set
441.10
(vi)
8 way ( RCCB : 60A, 100 mA sensitivity).
Per set
494.90
Three Phase Distribution Boards c/w RCCB 100 mA sensitivity
(i)
4 way ( RCCB : 40A, 100 mA sensitivity).
Per set
979.00
(ii)
4 way ( RCCB : 60A, 100 mA sensitivity).
Per set
1,032.80
(iii)
6 way ( RCCB : 40A, 100 mA sensitivity).
Per set
1,075.80
(iv)
6 way ( RCCB : 60A, 100 mA sensitivity).
Per set
1,108.10
(v)
8 way ( RCCB : 40A, 100 mA sensitivity).
Per set
1,253.40
(vi)
8 way ( RCCB : 60A, 100 mA sensitivity).
Per set
1,377.10
Three Phase Distribution Boards c/w RCCB 300 mA sensitivity
(i)
4 way ( RCCB : 40A, 300 mA sensitivity).
Per set
936.00
(ii)
4 way ( RCCB : 60A, 300 mA sensitivity).
Per set
979.00
(iii)
6 way ( RCCB : 40A, 300 mA sensitivity).
Per set
1,016.70
(iv)
6 way ( RCCB : 60A, 300 mA sensitivity).
Per set
1,065.10
(v)
8 way ( RCCB : 40A, 300 mA sensitivity).
Per set
1,215.70
(vi)
8 way ( RCCB : 60A, 300 mA sensitivity).
Per set
1,301.80
SOR ELEC 2014/Page 10 of 10
