#P278 - 1909 Packard 30

A great replica of days gone by with

real opening doors and curved
fenders. 17 long.

mir-izdeliy.at.ua
 #P278 - Assembly Instructions
1. Select your material from a variety of
C hardwoods or solid core plywood.
I G 2. Measure each pattern piece and cut the
work pieces to size accordingly. Sand as
F
necessary.
K L 3. Make all pattern pieces by adhering the
paper patterns to the work pieces with a
M D
B A repositionable spray adhesive. Cut the outer
O shapes and any interior designs. And drill
where indicated.
N 4. Remove all paper patterns. Sand where
needed. The edges can be rounded by sanding
J or using a small roundover router bit if desired.
H
#P278 E 5. Assemble by first attaching the Rear, Center
1909 Packard Model 30 Two Door Coupe and Front Windows to one Side. Then attach
the 2 Seat Backs, Seats, and Seat Bases to the
same Side. Next, attach the remaining Side
and Roof. Set this assembly into position on
mir-izdeliy.at.ua the Frame and secure from the underside.
Next, attach the Hood and Radiator assembly
to the Frame. Then attach the Wheels, Fenders,
Bumpers, and lights and finish as desired.

GREAT AMERICAN

DOWNLOADABLE PATTERNS TM
The Berry Basket Copyright 2002 All Rights Reserved
www.greatamericanscrollsaw.com a division of The Berry Basket
Rear Bumper (O) Top view

#P278
1909 Packard Model 30 Two Door Coupe
Description Item Qty Size
Side A 2 3/8T x 4 3/8W x 9 5/8L
Front Bumper (N) Stock: 3/4

Door B 2 3/8T x 2W x 3 5/8L

Rear Bumper (O) Stock: 3/4

Roof C 1 3/8T x 4 1/2W x 10 1/4L

Hood D 1 2 5/8T x 3W x 3 1/2L
Frame E 1 3/4T x 4 1/2W x 15 1/4L
Radiator F 1 3/8T x 2W x 3L
Front Window G 1 3/8T x 4 3/8W x 4 1/2L
Center Window H 1 3/8T x 3 3/4W x 4 3/8L
Rear Window I 1 3/8T x 3 3/4W x 4 3/8L
Fender J 2 3/4T x 2 5/8W x 15L
Seat Back K 2 3/8T x 1 1/2W x 3 3/4L
Seat L 2 3/8T x1 13/16W x 3 3/4L
Seat Base M 2 1 1/4T x 1 1/4W x 3 3/4L
Front Bumper N 1 3/4T x 3/4W x 6 1/4L
#P278 Rear Bumper O 1 3/4T x3/4W x 6 1/4L
 #P278
Drill using a #52 drill bit (#A157)
and use a #17 x 3/4 finishing nail
for door hinge

Side (A) A
Stock: 3/8, cut 2 Door instructions: With table flat, start at A
Left pattern piece. B and cut through B and C, ending at D. Then
with table tilted down to the left at 10 and

mir-izdeliy.at.ua
using a #9 blade, cut from D to A on the right
door and from A to D on the left door.
Front Window (G)

Rear Window (I)

Door (B) Center Window (H)
Drill for tail light #A247 Stock: 3/8, cut 2

Small dashed
lines indicate
placement of
Dashed Seat assembly
lines indicate C
Pattern overlap line

placement of D
Seat assembly

Frame (E) Fender (J)

The Berry Basket Copyright 2002

 mir-izdeliy.at.ua

Radiator (F)
Hood (D) goes here
Thickness: 2,
top view

Silicon 1/16 brass

welding rod here for
Hood hinge and on
Door for handle
Front of auto

Side (A)

Front Bumper (N) Top view

cut at a 10 angle

Door hinge
Right Door
Left Door
Door hinge
Top view of Doors

Side (A)
3/8 T

3/8 T

Right pattern piece.

Stock: 3/8, cut 2
Side (A)

Front Window (G)

#P278 Pattern overlap line

The Berry Basket Copyright 2002

 #P278
Seat (L)
Stock: 3/8
Seat Back (K)
Stock: 3/8
mir-izdeliy.at.ua

Roof (C)
Stock: 3/8

The Berry Basket Copyright 2002

 #P278
Optional: cut off the end of the axle peg.
Taper the end by sanding so that a brass
cap nut will fit on as the hub cap.

Drill 3/8 for axle peg and

2 3/4 wheel - #A244

Frame (E)
Stock: 3/4
Left pattern piece.
mir-izdeliy.at.ua

Rear Window (I)

Center Window (H)
Seat Assembly goes here

Reart Bumper (O)

Seat Assembly goes here
Pattern overlap line

The Berry Basket Copyright 2002

 Front Bumper (N)

Radiator (F)

Hood (D) goes here

NOTE: To get the

Seat Back (K) goes here

curved shape of the

Seats, we recommend
sanding over cutting
as it is safer. The shape
goes here
Steering

shown in the side view

wheel

is intended to be used
as a guide only.

Seat (J) goes here

Front Window goes here
Right pattern piece.

Seat Base (M) goes here

Frame (E)
Stock: 3/4

Pattern overlap line

Seat Base (M)

Thickness: 1 1/4,
front view

Seat Assembly goes here

mir-izdeliy.at.ua
#P278
The Berry Basket Copyright 2002
 Front Window (G)
Stock: 3/8

Drill 3/16 at a slight angle

for steering wheel - #A245

Recommended: before cutting the outer shape of

the Hood and the Radiator - cut the interior design
of the Radiator, then glue the Radiator to the Hood
and cut the outer shape of both.

Optional: brass can be glued to the front of the

Radiator before cutting

Radiator (F) Stock: 3/8, front view

Center Window (H)

Stock: 3/8

Hood (D)
Thickness 2, front view

#P278
mir-izdeliy.at.ua
The Berry Basket Copyright 2002
 Pattern overlap line Rear Window (I)
Stock: 3/8

Drill for tail light,

stock #A247

Drill for spare tire

Left pattern piece.
Stock: 3/4, cut 2
Fender (J)

for ts
r ill ligh
D ead 6
H 24
#A

J) 2 .
e r ( , cutpiece
d 4 n
Pa

n 3/ er
Fetock: t patt
tte
rn

S igh
ov

R
erl
ap
lin

#P278
e

mir-izdeliy.at.ua The Berry Basket Copyright 2002