Scribd
Upload
275 views1 page

WPS

This document provides the welding procedure specification for joining P355NH steel with an E310-16 filler wire. Some key details include: - The base metal is P355NH steel with a thickness of up to 12mm. - Welding will be done in the Y position using gas metal arc welding with an E310-16 solid wire and a shielding gas. - Parameters include a welding current of 121.2A, voltage of 16.06V, and wire feed speed of 11.37 cm/min. - Inspections will include visual, radiographic, ultrasonic, and dimensional examinations.

Uploaded by

Rodica Timofte
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
275 views1 page

WPS

This document provides the welding procedure specification for joining P355NH steel with an E310-16 filler wire. Some key details include: - The base metal is P355NH steel with a thickness of up to 12mm. - Welding will be done in the Y position using gas metal arc welding with an E310-16 solid wire and a shielding gas. - Parameters include a welding current of 121.2A, voltage of 16.06V, and wire feed speed of 11.37 cm/min. - Inspections will include visual, radiographic, ultrasonic, and dimensional examinations.

Uploaded by

Rodica Timofte
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

WPS N

SPECIFICATIE PROCEDURII DE SUDARE /


WELDING PROCEDURE SPECIFICATION (EN 15609) Rev. / Issue:
00
Normativ/ Standard : EN 15614-1:2008 S.C. . S.R.L. WPAR:

Materiale de baza/ Grosime MB 1 / BM 1 Calitate/ Grup/


thickness Quality Group
Base Metal
Grosime MB 2 / BM 2 thickness Calitate/ Grup/
(BM) Quality Group
P355NH Grosime suport / support Calitate/ Grup/
thickness Quality Group
Sarma Clasificare/ Furnizor/ Lot/
tubulara/ Classification Supplier Batch
Material(e) de
Cored wire
adaos / Solid wire/ Clasificare / Furnizor/ Lot/
Filler(s) sarma plina Classification Supplier Batch
FRO INOX E310-16 Flux/ flux
Clasificare / Furnizor/ Lot/
Classification Supplier Batch
Sanfren /Groove:Y Unghi / Angle: 60
Inaltime rost(mm) / Depth of root face: 10 Deschidere rost(mm)/ Gap : 3
Schema imbinare / Detail of joint: Succesiune treceri/ Welding Sequences :

Metoda/ Temp. / Temperature (C) Temperatura intre straturi/Interpass


Pre-incalzire / Preheat Method
+1150
Temp.
Secventa de sudura / Welding Sequence
Weding Parameters Parametri de sudura/

Procesul de sudura / Welding process SMEI


Pozitia sudurii / Welding Position Y
Material de Adaos / Filler Metal FRO INOX E310-16
Diametru / Diameter (mm) 3.2
Gaz de protectie / Shielding Gas
Debit / Flow Rate (1/min)
Compozitie / Composition (%) 0.08-0.20 C , 1.00-2.50 Mn , 0.30-0.75 Si
Polaritate / Polarity (-/+)
Intensitatea curentului / Welding Current (A) 121.2
Tensiune / Arc Voltage (V) 16.06
Viteza sarmei / Wire Feeding Speed (cm/min)
Viteza de sudare / Travel Speed (cm/min) 11.37
N de treceri/ Run n 8-12

Tratament termic / Incalzire / Heating (C/h) Racire/ Cooling. (C/h) Temp.palier + timp
Post Weld Heat Treatment Durata / During (h) Durata/ Soak temp (C)

Verificare si incercari / Vizual / Radiatii penetrante / Ultrasunete/ Dimensional /


Inspection and Tests Visual Examination Radiographic Examination Ultrasonic Examination Dimensional Examination
Lichide penetrante la Pulberi magnetice/ Fazorul / Altele/ Others
radacina/ Magnetic Powder PAUT
Dye Penetrant on root Examination

Elaborat de / Issued by: ___/___/___ Aprobat de / Approved by: ___/___/___ Client / Altii (Client /Others): ___/___/___

You might also like