English Manual
1. Introduction
The LINDY IPower Switch Classic is an Internet ready device designed and is equipped with an
intelligent current-meter (True RMS) that will indicate the total power consumption of a power
strip. The LINDY IPower Switch Classic offers an easy set up and user-friendly communication
software. This software provides assistance to the network administrator to remotely monitor the
multiple PDU power consumption to realize the total current power consumption.
IPower Switch Classic 8 Features
IPower Switch Classic 16 Built-in web server, supports real time monitoring for the current
consumption of the power strip.
Build-in true RMS current meter.
Easy setup, the display shows the current IP address of the unit directly.
User Manual English Provides audio alarm when the power consumption exceeds the value setting
for overload warning.
Sends email and SMNP traps when the power consumption exceeds the value
for overload warning.
Software utility included, which monitors a number of IPower Switches Classic
simultaneously
Supports the SNMP protocol and provides an MIB for the unit.
Provides power protection by a circuit breaker.
Slim size - suitable for a variety of rack environments.
Real time control for each outlet.
LED status indicator for every outlet.
Power on switching sequence adjustable.
2. Package Content
The standard Amazing PDU package contains a Power Distribution Unit with supporting
hardware and software. The components of the package are:
Power Distribution Unit.
Rack mount Brackets.
CD-ROM, containing:
User Manual.
Amazing PDU Software.
MIB: Management Information Base for Network. (AmazingMIB.mib)
Adobe Acrobat Reader.
LINDY No. 32657, 32658
For Home and Office Use
Tested to Comply with
FCC Standards
www.LINDY.com 2
LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (Jun 2009)
English Manual English Manual
3. Function
4. Installation
This section will instruct you to quickly install the Amazing PDU.
Interface:
Function Description
Ethernet Network connection for the built-in web server
Audible Alarm 1. Warning: 1 beep in 1 second
2. Overload: 3 beeps in 1 second
Note: the overload alarm will not stop until the current falls back to
0.5 Amps below the setting value for overload or warning.
Function Button 1. Press and release this button to turn off the warning audible alarm.
The overload alarm cant be stopped by this button.
2. Pressing the button and releasing it after two beeps will show up
the units IP address
3. Pressinfg the button and releasing it after 4 beeps changes the IP
address mode from fixed to DHCP and vice versa
4. Pressing the button and releasing it after 6 beeps restarts the
network interface.
Meter Displays the current or the IP address of the unit
LED Indicator Current: Lights to indicate that the power consumtion is shown in the Hardware Installation
display
IP Address: Lights to indicate that the IP Address is shown in the display 1. Install mounting brackets.
Output LED Indicates, wether a power output is switched on The Unit comes with brackets for mounting in a rack. To mount the
device into a rack, please perform the following procedure:
I. Attach the mounting brackets to the unit, using the four retaining screws
provided for each of the brackets.
II. Choose a mounting position for the brackets (several options).
III. Align the mounting holes of brackets with the notched hole on the vertical rail
and attach with the retaining screws.
2. Connect the input and output power cables.
3. Connect your Ethernet cable to the unit.
4. Switch on the Ipower Switch Classic.
Note :
The default setting for the way to get an IP address is DHCP. If the unit cant get an IP from a
present DHCP server, the IP address will remain 192.168.0.216
3 4
English Manual English Manual
5. Web Interface Network
Index
1. Provides network information for the
System Information
IPowerSwitch.
Provide the General Information
2. The network setting can be changed
for the IPower Switch, including:
here.
3. The default ID is snmp, the password
Model No.
is 1234.
Name
Location
Contact
Firmware Version
MAC Address
Treshold
Shows the warning and overload value
setting
Status: ID
Indicates the IPower Switchs power
consumption and status.
Change the ID and password.
The default ID is snmp,
The password is 1234.
Control
Status:
1. Indicates the Ipower Switchs power
consumption and status.
2. Select the outlet by check box first and
click the on or off button to control the
IPower Switch power output. Email
In case of an SMNP-event or warning ,
Control: the unit can send out an email
message to a pre-defined account.
The default ID is snmp and Only support the input of anemail
password is 1234. server with a domain name.
The message in the email will show as
below:
Indicate OutletA~H status order
0 : means the power off.
1 : means the power on.
5 6
English Manual English Manual
Trap
FCC Warning
Defines the IP address, to send event traps to. This device complies with part 15 of the FCC Rules.
The default ID is snmp, the Password is Operation is subject to the following two conditions:
1234. 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
CE Statement, EMC Compatibilty
This device complies with EN Standards EN55022 and EN55024 according to the relevant EC EMC
Directive. It must be used with shielded cables only to maintain EMC compatibility.
Dieses Produkt entspricht den einschlgigen EMV Richtlinien der EU und darf nur zusammen mit
abgeschirmten Kabeln verwendet werden.
6. Technical Specifications
Interface
RJ45 Ethernet
LINDY Herstellergarantie
Nominal Input Frequency 47~63 Hz Full Range LINDY gewhrt fr dieses Produkt ber die gesetzliche Regelung hinaus eine zweijhrige
Herstellergarantie ab Kaufdatum. Die detaillierten Bedingungen dieser Garantie finden Sie auf der
LED Indicators LINDY Website aufgelistet bei den AGBs.
Indicator (1)yellow LED (1) red LED
Current Meter 3 digits
WEEE (Waste of Electrical and Electronic Equipment),
Range 0A~20A (True RMS) Recycling of Electronic Products
Resolution 0A~20A: 0.1A
Precision 0A~20A: +/-2%+/-0.1AMP In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste
electrical and electronic equipment. The wheelie bin symbol shown indicates that this product must not
Alarm be disposed of with household waste. Instead the product must be recycled in a manner that is
Audible 1. Warning- 1 beep per second environmentally friendly. For more information on how to dispose of this product, please contact your
2. Overload- 3 beeps per second local recycling centre or your household waste disposal service. Each individual EU member state has
Seven Segment Warning and Overload - Meter flashes once per second implemented the WEEE regulations into national law in slightly different ways. Please follow your
national law when you want to dispose of any electrical or electronic products.
Operation & Environment
More details can be obtained from your national WEEE recycling agency.
Operating Temperature -5 - 45 degree C
Relative Humidity 0 - 95% Germany / Deutschland
Storage Temperature -25 - 65 degree C Die Europische Union hat mit der WEEE Direktive umfassende Regelungen fr die Verschrottung und
das Recycling von Elektro- und Elektronikprodukten geschaffen. Diese wurden von der Bundesregierung
im Elektro- und Elektronikgertegesetz ElektroG in deutsches Recht umgesetzt. Dieses Gesetz
verbietet vom 24.Mrz 2006 an das Entsorgen von Elektro- und Elektronikgerten ber die
Hausmlltonne! Diese Gerte mssen den lokalen Sammelsystemen bzw. rtlichen Sammelstellen
zugefhrt werden! Dort werden sie kostenlos entgegen genommen. Die Kosten fr den weiteren
Recyclingprozess bernimmt die Gesamtheit der Gertehersteller.
LINDY No 32657, 32658
1st Edition, September 2008
www.lindy.com
7 8
