LAZY AXE ACCESS 910 PRINT COMMANDS

Issue 4 (Local 7.2 and TL 4.2)

STC

DIRRP:RP=rp or ALL; RP & EM Events.

STC EXEMP:RP=rp,EM=em or ALL; EM data.
EXCLP:EQM=ALL; Control Signalling Link data.
EXCLP:EQM=CLC-x; Control Signalling Link data.
EXEGP:EMG=emg or ALL; EMG Control signalling link device.
EXRPP:RP=rp or ALL; RP data.

STC-M RPG Connected.

RPG DIRRP:RP=rp or ALL; RP & EM Events.

EXEMP:RP=rp,EM=em or ALL; EM data
EXCGP:DEV=CSLDEV-x; or ALL; GS connected CLC Device
EXCPP:EMG=emg or ALL[,RDL]; GS connected CLCs,
EXCPP:EQM=ALL[,RDL]; RDL = Redundancy Level
EXCPP:EQM=CSLM7-x[,RDL]; As above.
EXEGP:EMG=emg or ALL; EMG Control signalling link device.
EXRPP:RP=rp or ALL; RP data
Device and GS connection.

RPG for V5.1 AU(Pots,BA),TAU Both AU & TAU require individual RPGs
RPG
DIRRP:RP=rp or ALL; RP & EM Events.
EXDRP:DEV=STAU-x or STTAU-x; Used to locate connected RPG.
EXEMP:RP=rp,EM=em or ALL; EM data
EXRPP:RP=rp or ALL; RP data
GNACP:AG=ag or ALL; GAM Data Connection.
GNACP:CONCG=concg or ALL; Connected to concentration group
GNACP:DIP=dip; AG connection.
GNSPP:DIP=xLIAU or xLITAU; GAM Signalling Channel Path
GNSPP:SNT=ALL; GAM Signalling Channel Path
GNSPP:SNT=STAU-x or STTAU-x; GAM Signalling Channel Path
GNSTI:SNT=STAU-x or STTAU-x; Transfer NT to another free RPG.
NTCOP:SNT=STAU-x or STTAU-x; Device and GS connection.
GSD GSD Multiple positions & connected devices.

EXMDP:MUP=mup; (eg GS-3-10) Multiple position and Device connections

NTCOP:SNT= ETRST-x or ALL; Shows DIP and Device connections.
NTCOP:SNTP=sntp or ALL; As above. (Eg. SNTP=TSM-2-4&&-7)
NTSTP:SNT=ETRST-x or ALL; Shows SNT status.

ETC4 RST devices

ETC
EXDRP:DEV=RST-x; Shows ETC connected RP / EM & route.
EXDEP:DEV=RST-x Shows SNT and EMG route.
DTDIP:DIP=xETRST; Connected SNT.
DTIDP:DIP=dip or ALL: DIP initial data.
DTSTP:DIP=xETRST; DIP status.
STDEP:DEV=RST-x; RST device status.

Robert Walker, EGS Australia, Phone ECN 880 4606. 31/08/17 Page 1
 AUS (Equivalent to EMG EM)

DIREP:EMG=emg or ALL; EMG Event Record.

EXEDP:EMG=emg,EM=em; Shows loaded software.
EXEGP:EMG=emg or ALL; EMG Control signalling link device.
EXEIP:EMG=emg,EM=em or ALL; EMRP Information, EMRP type.
EXEPP:EMG=ALL,EM=ALL; EMG EM Processor Control State.
EXEPP:EMG=emg,EM=em or ALL; As above.
EXHWP:MACCG=emg; All hardware information.
EXHWP:PIU=AUS-x; As above.
AUS EXMCP; Multiple Access Groups to EMGs
(EMG) EXPUP:MACCG=emg[,SR=sr Position, subrack and states of PIU.
[MACCG] [,POS=pos...]];
EXPUP:PIU=AUS-x or AUEP-x; As above.
EXSMP:ENB=ALL,ANL,EMG=emg; Emergency lines & Announcement lines.
EXSMP:ENB=ALL,ANL; As above.
NNBLE:NODE=AUS-x; Deblock AUS.
NNBLI:NODE=AUS-x; Block AUS.
NNCDP:MACCG=emg; Network nodes characteristics (Clock).
NNCDP:NODE=AUS-x or ALL; As above.
NNCOP:MACCG=emg; Shows AUS hardware variant.
NNCOP:NODE=AUS-x or ALL; As above.
NNIDP:MACCG=emg; Shows Node Mesh & AUS status.
NNIDP:NODE=AUS-x[&&-x]; As above.
NNSTP:MACCG=emg; Shows Node State.
NNSTP:NODE=AUS-x [,LIST]; As above.
NNSTP:NODE=AUS-ALL; As above.
NNTEI:NODE=AUS-x; Initiates testing the AUS.
NNUPP:MACCG=emg; Shows connected Devices/DIPs to Ports
NNUPP:NODE=AUS-x[&&-x]; As above.
NNUPP:NODE=AUS-x As above.
[,PORT=port];
PWESP:MACCG=emg(,SWITCHED); Protection switching equipment state.
(SWITCH only PIUs with protected
switching will be printed)
PWSCC:PIU=piu...,AUTO=auto Automatic protection switching (Yes/No).
[,LIM=lim]; (1-100) Set percentage of faulty devices on a
PWSCC:PIUTYPE=AUS[,AUTO=aut] board before a automatic switch is done.
[,LIM=lim]; (1-100)
PWSCP:PIU=AUS-x; Protection switching equipment criteria.
PWSCP:PIUTYPE=AUS; Protection switching for type AUS.
RECEI:EMG=emg,EMRP=x-A; Repair EMRP.
RECEI:EMG=emg,STR=A or B; Repair STR.
REMEI:EMG=emg,MAG=EM-x, Maintenance Block EMRP.
PCB=EMRPI;
REMEI:EMG=emg,MAG=STR-A/B, Maintenance Block STR.
PCB=EMRPI;
REPEI:EMG=emg,EMRP=x-A; Fault Repair EMRP.
REPEI:EMG=emg,STR=A or B; Fault Repair STR.
SYESI:EMG=emg,EM=em or ALL, Restart with or without Reload
EMRPRANK=RELOAD; Use MINRQ or COMPL or RELOAD

Robert Walker, EGS Australia, Phone ECN 880 4606. 31/08/17 Page 2
 TAU(Equivalent = SLCT +more)

BLPFI:PIU=TAU-x Forced TAU blocking.

BLPUI:PIU=TAU-x; Block TAU. Need to block DIP first.
BLPUE:PIU=TAU-x; Deblock TAU.
TAU DTSTP:DIP=xLITAU; DIP status.
EXHWP:PIU=TAU-x; TAU hardware information.
EXPCP:PIU=TAU-x[&&-x]; Shows Device and DIP connection.
EXPUP:MACCG=emg; Shows TAU to AU communication status.
Shows status of specific position in a
EXPUP:MACCG=emg,SR=sr, subrack.
POS=pos..; As above.
EXPUP:PIU=TAU-x[&&-x]; Shows TAU sub rack connection.
Test
Bus
EXTCP:MACCG=emg; Change TAU connection to sub rack.
EXTGC:PIU=piu,SR=sr; Shows TAU connected to sub rack.
EXTGP:MACCG=emg,SR=sr; Shows the sub rack TAU located in.
EXTGP:PIU=TAU-x; Shows what software is loaded.
FCLPP:PIU=TAU-x,[LOADED]; As above.
FCLPP:SUID=suid,MACCG=emg; Shows current phase and status.
FCPUP; Test System access to Debugger.
TEPUI:PIU=TAU-x;

AU For both POTs & BA.

BLPFI:PIU=AU-x; Forced AU blocking.

BLPUI:PIU=AU-x; Block AU. Need to block DIP first.
BLPUE:PIU=AU-x; Deblock AU.
DTSTP:DIP=xLIAU; DIP status.
EXHWP:PIU=AU-x; AU hardware information.
EXPCP:PIU=AU-x[&&-x]; Shows Device and DIP connection.
EXPUP:MACCG=emg; Shows TAU to AU communication status.
EXPUP:PIU=AU-x[&&-x]; Shows what software is loaded.
FCLPP:PIU=AU-x; Subscriber line circuit test.
SLOCI:PIU=AU-x; As above.
SLOCI:SNB=snb; As above.
AU SLOCI:DEV=dev; Test subscriber line.
SLOMI:DEV=dev,MP=11; As above.
SLOMI:SNB=snb,MP=11; To finish SLOMI command.
:END; Test System access to Debugger.
TEPUI:PIU=AU-x; Var SYSTMANSTATE contains V5.1
PRINT VAR CTRLAU 0-:57; Interface state.
HF = Null means not started
H0 = Starting Up.
H4 = Working. See Plex for other states

Robert Walker, EGS Australia, Phone ECN 880 4606. 31/08/17 Page 3
 AUS LED FUNCTION

AUS PIU

MIA Red Manual Intervention Allowed OAM

PWR Green Power OK. On = Stable power source.

On = Active control signalling link

COM Green Communication protocol OK.
protocol towards APZ.

SYN Yellow Clock Synchronisation On = Proper synchronisation

Flash = 1 synch ring missing.

CSR Yellow Call Set up Rate Flash One flash = A call is set up in
the time switch.

TL1 Yellow Traffic Level 1 indication TL1 off + TL2 off = no traffic.
TL1 on + TL2 off = 0<X<100

TL2 Yellow Traffic Level 2 indication TL1 off + TL2 on = 100<X<200

TL1 on + TL2 on = 200< calls

Robert Walker, EGS Australia, Phone ECN 880 4606. 31/08/17 Page 4