Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt

Formatted: Font: 8 pt
Formatted: Font: 8 pt

SECTION 017300 - EXECUTION Formatted: Font: 8 pt

Formatted: Tab stops: 6.25", Right + Not at 6.5"
TIPS:

To view non-printing Editor's Notes that provide guidance for editing, click on MasterWorks/Single-
File Formatting/Toggle/Editor's Notes.

To read detailed research, technical information about products and materials, and coordination
checklists, click on MasterWorks/Supporting Information.

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Special Conditions and other Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section includes general administrative and procedural requirements governing execution of

the Work including, but not limited to, the following:

1. Construction layout.
2. Field engineering and surveying.
3. Installation of the Work.
4. Cutting and patching.
5. Coordination of OwnerRoyal Commission-installed products.
6. Progress cleaning.
7. Starting and adjusting.
8. Protection of installed construction.

B. Related Requirements:

1. Section 011000 "Summary" for limits on use of Project site.

2. Section 013300 "Submittal Procedures" for submitting surveys.
3. Section 017700 "Closeout Procedures" for submitting final property survey with
Project Record Documents, recording of OwnerRoyal Commission-accepted
deviations from indicated lines and levels, replacing defective work, and final
cleaning.
4. Section 024119 "Selective Demolition" for demolition and removal of selected
portions of the building.
5. Section 078413 "Penetration Firestopping" for patching penetrations in fire-rated
construction.

1.3 DEFINITIONS

A. Cutting: Removal of in-place construction necessary to permit installation or performance of Formatted: Font: 8 pt
subsequent work. Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 1 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
B. Patching: Fitting and repair work required to restore construction to original conditions after
installation of subsequent work. Formatted: Font: 8 pt
Formatted: Tab stops: 6.25", Right + Not at 6.5"

1.4 PREINSTALLATION MEETINGS

A. Cutting and Patching Conference: Conduct conference at [Project site] <Insert location>.

1. Prior to [submitting cutting and patching plan] [commencing work requiring

cutting and patching], review extent of cutting and patching anticipated and
examine procedures for ensuring satisfactory result from cutting and patching work.
Require representatives of each entity directly concerned with cutting and patching to
attend, including the following:

a. Contractor's superintendent.
b. Trade supervisor responsible for cutting operations.
c. Trade supervisor(s) responsible for patching of each type of substrate.
d. Mechanical, electrical, and utilities subcontractors' supervisors, to the extent
each trade is affecting by cutting and patching operations.

2. Review areas of potential interference and conflict. Coordinate procedures and

resolve potential conflicts before proceeding.

1.5 INFORMATIONAL SUBMITTALS

A. Qualification Data: For [land surveyor] [professional engineer].

B. Certificates: Submit certificate signed by [land surveyor] [professional engineer]

certifying that location and elevation of improvements comply with requirements.

C. Cutting and Patching Plan: Submit plan describing procedures at least [10] <Insert
number> days prior to the time cutting and patching will be performed. Include the
following information:

1. Extent: Describe reason for and extent of each occurrence of cutting and patching.
2. Changes to In-Place Construction: Describe anticipated results. Include changes to
structural elements and operating components as well as changes in building
appearance and other significant visual elements.
3. Products: List products to be used for patching and firms or entities that will perform
patching work.
4. Dates: Indicate when cutting and patching will be performed.
5. Utilities and Mechanical and Electrical Systems: List services and systems that
cutting and patching procedures will disturb or affect. List services and systems that
will be relocated and those that will be temporarily out of service. Indicate length of
time permanent services and systems will be disrupted.

a. Include description of provisions for temporary services and systems during

interruption of permanent services and systems.

D. Landfill Receipts: Submit copy of receipts issued by a landfill facility, licensed to accept
hazardous materials, for hazardous waste disposal. Formatted: Font: 8 pt
Formatted: Font: 8 pt
E. Certified Surveys: Submit [two] <Insert number> copies signed by [land surveyor]
[professional engineer]. Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 2 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
F. Final Property Survey: Submit [10] <Insert number> copies showing the Work performed
and record survey data. Formatted: Font: 8 pt
Formatted: Tab stops: 6.25", Right + Not at 6.5"

1.6 QUALITY ASSURANCE

A. Land Surveyor Qualifications: A professional land surveyor who is legally qualified to

practice in jurisdiction where Project is located and who is experienced in providing land-
surveying services of the kind indicated.

B. Cutting and Patching: Comply with requirements for and limitations on cutting and patching
of construction elements.

1. Structural Elements: When cutting and patching structural elements, notify

ArchitectRoyal Commission of locations and details of cutting and await directions
from ArchitectRoyal Commission before proceeding. Shore, brace, and support
structural elements during cutting and patching. Do not cut and patch structural
elements in a manner that could change their load-carrying capacity or increase
deflection.
2. Operational Elements: Do not cut and patch operating elements and related
components in a manner that results in reducing their capacity to perform as intended
or that results in increased maintenance or decreased operational life or
safety.[ Operational elements include the following:]

a. Primary operational systems and equipment.

b. Fire separation assemblies.
c. Air or smoke barriers.
d. Fire-suppression systems.
e. Plumbing piping systems.
f. Mechanical systems piping and ducts.
g. Control systems.
h. Communication systems.
i. Fire-detection and -alarm systems.
j. Conveying systems.
k. Electrical wiring systems.
l. Operating systems of special construction.
m. <Insert operating system>.

3. Other Construction Elements: Do not cut and patch other construction elements or
components in a manner that could change their load-carrying capacity, that results in
reducing their capacity to perform as intended, or that results in increased
maintenance or decreased operational life or safety.[ Other construction elements
include but are not limited to the following:]

a. Water, moisture, or vapor barriers.

b. Membranes and flashings.
c. Exterior curtain-wall construction.
d. Sprayed fire-resistive material.
e. Equipment supports.
f. Piping, ductwork, vessels, and equipment.
g. Noise- and vibration-control elements and systems.
h. <Insert miscellaneous element>. Formatted: Font: 8 pt
Formatted: Font: 8 pt
4. Visual Elements: Do not cut and patch construction in a manner that results in visual
Formatted: Font: 8 pt
evidence of cutting and patching. Do not cut and patch exposed construction in a
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 3 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
manner that would, in ArchitectRoyal Commission's opinion, reduce the building's
aesthetic qualities. Remove and replace construction that has been cut and patched in Formatted: Font: 8 pt
a visually unsatisfactory manner. Formatted: Tab stops: 6.25", Right + Not at 6.5"

C. Manufacturer's Installation Instructions: Obtain and maintain on-site manufacturer's written

recommendations and instructions for installation of products and equipment.

PART 2 - PRODUCTS

2.1 MATERIALS

A. General: Comply with requirements specified in other Sections.

1. For projects requiring compliance with sustainable design and construction practices
and procedures, use products for patching that comply with sustainable design
requirements.

B. In-Place Materials: Use materials for patching identical to in-place materials. For exposed
surfaces, use materials that visually match in-place adjacent surfaces to the fullest extent
possible.

1. If identical materials are unavailable or cannot be used, use materials that, when
installed, will provide a match acceptable to ArchitectRoyal Commission for the
visual and functional performance of in-place materials.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Existing Conditions: The existence and location of underground and other utilities and
construction indicated as existing are not guaranteed. Before beginning sitework, investigate
and verify the existence and location of underground utilities,[ mechanical and electrical
systems,] and other construction affecting the Work.

1. Before construction, verify the location and invert elevation at points of connection of
sanitary sewer, storm sewer, and water-service piping; underground electrical
services; and other utilities.
2. Furnish location data for work related to Project that must be performed by public
utilities serving Project site.

B. Examination and Acceptance of Conditions: Before proceeding with each component of the
Work, examine substrates, areas, and conditions, with Installer or Applicator present where
indicated, for compliance with requirements for installation tolerances and other conditions
affecting performance. Record observations.

1. Examine roughing-in for mechanical and electrical systems to verify actual locations
of connections before equipment and fixture installation.
2. Examine walls, floors, and roofs for suitable conditions where products and systems
Formatted: Font: 8 pt
are to be installed.
3. Verify compatibility with and suitability of substrates, including compatibility with Formatted: Font: 8 pt
existing finishes or primers. Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 4 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
C. Written Report: Where a written report listing conditions detrimental to performance of the
Work is required by other Sections, include the following: Formatted: Tab stops: 6.25", Right + Not at 6.5"
Formatted: Font: 8 pt
1. Description of the Work.
2. List of detrimental conditions, including substrates.
3. List of unacceptable installation tolerances.
4. Recommended corrections.

D. Proceed with installation only after unsatisfactory conditions have been corrected.
Proceeding with the Work indicates acceptance of surfaces and conditions.

3.2 PREPARATION

A. Existing Utility Information: Furnish information to [local utility] [OwnerRoyal

Commission] that is necessary to adjust, move, or relocate existing utility structures, utility
poles, lines, services, or other utility appurtenances located in or affected by construction.
Coordinate with authorities having jurisdiction.

B. Field Measurements: Take field measurements as required to fit the Work properly.
Recheck measurements before installing each product. Where portions of the Work are
indicated to fit to other construction, verify dimensions of other construction by field
measurements before fabrication. Coordinate fabrication schedule with construction
progress to avoid delaying the Work.

C. Space Requirements: Verify space requirements and dimensions of items shown

diagrammatically on Drawings.

D. Review of Contract Documents and Field Conditions: Immediately on discovery of the need
for clarification of the Contract Documents caused by differing field conditions outside the
control of Contractor, submit a request for information to ArchitectRoyal Commission
according to requirements in Section 013100 "Project Management and Coordination."

3.3 CONSTRUCTION LAYOUT

A. Verification: Before proceeding to lay out the Work, verify layout information shown on
Drawings, in relation to the property survey and existing benchmarks. If discrepancies are
discovered, notify ArchitectRoyal Commissions [ and Construction Manager] promptly. Formatted: Font: Not Bold

B. General: Engage a [land surveyor] [professional engineer] to lay out the Work using
accepted surveying practices.

1. Establish benchmarks and control points to set lines and levels at each story of
construction and elsewhere as needed to locate each element of Project.
2. Establish limits on use of Project site.
3. Establish dimensions within tolerances indicated. Do not scale Drawings to obtain
required dimensions.
4. Inform installers of lines and levels to which they must comply.
5. Check the location, level and plumb, of every major element as the Work progresses.
6. Notify ArchitectRoyal Commissions [ and Construction Manager] when deviations Formatted: Font: Not Bold
from required lines and levels exceed allowable tolerances. Formatted: Font: 8 pt
7. Close site surveys with an error of closure equal to or less than the standard
Formatted: Font: 8 pt
established by authorities having jurisdiction.
Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 5 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Tab stops: 6.25", Right + Not at 6.5"
C. Site Improvements: Locate and lay out site improvements, including pavements, grading,
fill and topsoil placement, utility slopes, and rim and invert elevations. Formatted: Font: 8 pt
Formatted: Font: 8 pt
D. Building Lines and Levels: Locate and lay out control lines and levels for structures,
building foundations, column grids, and floor levels, including those required for
mechanical and electrical work. Transfer survey markings and elevations for use with
control lines and levels. Level foundations and piers from two or more locations.

E. Record Log: Maintain a log of layout control work. Record deviations from required lines
and levels. Include beginning and ending dates and times of surveys, weather conditions,
name and duty of each survey party member, and types of instruments and tapes used. Make
the log available for reference by ArchitectRoyal Commissions [ and Construction Formatted: Font: Not Bold
Manager].

3.4 FIELD ENGINEERING

A. Identification: OwnerRoyal Commission will identify existing benchmarks, control points,

and property corners.

B. Reference Points: Locate existing permanent benchmarks, control points, and similar
reference points before beginning the Work. Preserve and protect permanent benchmarks
and control points during construction operations.

1. Do not change or relocate existing benchmarks or control points without prior written
approval of ArchitectRoyal Commission[ or Construction Manager]. Report lost or
destroyed permanent benchmarks or control points promptly. Report the need to
relocate permanent benchmarks or control points to ArchitectRoyal Commission[ and
Construction Manager] before proceeding.
2. Replace lost or destroyed permanent benchmarks and control points promptly. Base
replacements on the original survey control points.

C. Benchmarks: Establish and maintain a minimum of [two] <Insert number> permanent

benchmarks on Project site, referenced to data established by survey control points. Comply
with authorities having jurisdiction for type and size of benchmark.

1. Record benchmark locations, with horizontal and vertical data, on Project Record
Documents.
2. Where the actual location or elevation of layout points cannot be marked, provide
temporary reference points sufficient to locate the Work.
3. Remove temporary reference points when no longer needed. Restore marked
construction to its original condition.

D. Certified Survey: On completion of foundation walls, major site improvements, and other
work requiring field-engineering services, prepare a certified survey showing dimensions,
locations, angles, and elevations of construction and sitework.

E. Final Property Survey: Engage a [land surveyor] [professional engineer] to prepare a final
property survey showing significant features (real property) for Project. Include on the
survey a certification, signed by [land surveyor] [professional engineer], that principal
metes, bounds, lines, and levels of Project are accurately positioned as shown on the survey.
Formatted: Font: 8 pt
1. Show boundary lines, monuments, streets, site improvements and utilities, existing
Formatted: Font: 8 pt
improvements and significant vegetation, adjoining properties, acreage, grade
contours, and the distance and bearing from a site corner to a legal point. Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 6 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
2. Recording: At Substantial Completion, have the final property survey recorded by or
with authorities having jurisdiction as the official "property survey." Formatted: Font: 8 pt
Formatted: Tab stops: 6.25", Right + Not at 6.5"

3.5 INSTALLATION

A. General: Locate the Work and components of the Work accurately, in correct alignment and
elevation, as indicated.

1. Make vertical work plumb and make horizontal work level.

2. Where space is limited, install components to maximize space available for
maintenance and ease of removal for replacement.
3. Conceal pipes, ducts, and wiring in finished areas unless otherwise indicated.
4. Maintain minimum headroom clearance of [96 inches (2440 mm)] <Insert
dimension> in occupied spaces and [90 inches (2300 mm)] <Insert dimension> in
unoccupied spaces.

B. Comply with manufacturer's written instructions and recommendations for installing

products in applications indicated.

C. Install products at the time and under conditions that will ensure the best possible results.
Maintain conditions required for product performance until Substantial Completion.

D. Conduct construction operations so no part of the Work is subjected to damaging operations

or loading in excess of that expected during normal conditions of occupancy.

E. Sequence the Work and allow adequate clearances to accommodate movement of

construction items on site and placement in permanent locations.

F. Tools and Equipment: Where possible, select tools or equipment that minimize production
of excessive noise levels.

G. Templates: Obtain and distribute to the parties involved templates for work specified to be
factory prepared and field installed. Check Shop Drawings of other portions of the Work to
confirm that adequate provisions are made for locating and installing products to comply
with indicated requirements.

H. Attachment: Provide blocking and attachment plates and anchors and fasteners of adequate
size and number to securely anchor each component in place, accurately located and aligned
with other portions of the Work. Where size and type of attachments are not indicated,
verify size and type required for load conditions.

1. Mounting Heights: Where mounting heights are not indicated, mount components at
heights directed by ArchitectRoyal Commission.
2. Allow for building movement, including thermal expansion and contraction.
3. Coordinate installation of anchorages. Furnish setting drawings, templates, and
directions for installing anchorages, including sleeves, concrete inserts, anchor bolts,
and items with integral anchors, that are to be embedded in concrete or masonry.
Deliver such items to Project site in time for installation.

I. Joints: Make joints of uniform width. Where joint locations in exposed work are not
indicated, arrange joints for the best visual effect. Fit exposed connections together to form Formatted: Font: 8 pt
hairline joints.
Formatted: Font: 8 pt

J. Repair or remove and replace damaged, defective, or nonconforming Work. Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 7 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
1. Comply with Section 017700 "Closeout Procedures" for repairing or removing and
replacing defective Work. Formatted: Font: 8 pt
Formatted: Tab stops: 6.25", Right + Not at 6.5"

3.6 CUTTING AND PATCHING

A. Cutting and Patching, General: Employ skilled workers to perform cutting and patching.
Proceed with cutting and patching at the earliest feasible time, and complete without delay.

1. Cut in-place construction to provide for installation of other components or

performance of other construction, and subsequently patch as required to restore
surfaces to their original condition.

B. Existing Warranties: Remove, replace, patch, and repair materials and surfaces cut or
damaged during installation or cutting and patching operations, by methods and with
materials so as not to void existing warranties.

C. Temporary Support: Provide temporary support of work to be cut.

D. Protection: Protect in-place construction during cutting and patching to prevent damage.
Provide protection from adverse weather conditions for portions of Project that might be
exposed during cutting and patching operations.

E. Adjacent Occupied Areas: Where interference with use of adjoining areas or interruption of
free passage to adjoining areas is unavoidable, coordinate cutting and patching according to
requirements in Section 011000 "Summary."

F. Existing Utility Services and Mechanical/Electrical Systems: Where existing

services/systems are required to be removed, relocated, or abandoned, bypass such
services/systems before cutting to [minimize] [prevent] interruption to occupied areas.

G. Cutting: Cut in-place construction by sawing, drilling, breaking, chipping, grinding, and
similar operations, including excavation, using methods least likely to damage elements
retained or adjoining construction. If possible, review proposed procedures with original
Installer; comply with original Installer's written recommendations.

1. In general, use hand or small power tools designed for sawing and grinding, not
hammering and chopping. Cut holes and slots neatly to minimum size required, and
with minimum disturbance of adjacent surfaces. Temporarily cover openings when
not in use.
2. Finished Surfaces: Cut or drill from the exposed or finished side into concealed
surfaces.
3. [Concrete] [and] [Masonry]: Cut using a cutting machine, such as an abrasive saw
or a diamond-core drill.
4. Excavating and Backfilling: Comply with requirements in applicable Sections where
required by cutting and patching operations.
5. Mechanical and Electrical Services: Cut off pipe or conduit in walls or partitions to
be removed. Cap, valve, or plug and seal remaining portion of pipe or conduit to
prevent entrance of moisture or other foreign matter after cutting.
6. Proceed with patching after construction operations requiring cutting are complete.

H. Patching: Patch construction by filling, repairing, refinishing, closing up, and similar Formatted: Font: 8 pt
operations following performance of other work. Patch with durable seams that are as
Formatted: Font: 8 pt
invisible as practicable. Provide materials and comply with installation requirements
specified in other Sections, where applicable. Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 8 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
1. Inspection: Where feasible, test and inspect patched areas after completion to
demonstrate physical integrity of installation. Formatted: Font: 8 pt
2. Exposed Finishes: Restore exposed finishes of patched areas and extend finish Formatted: Tab stops: 6.25", Right + Not at 6.5"
restoration into retained adjoining construction in a manner that will minimize
evidence of patching and refinishing.

a. Clean piping, conduit, and similar features before applying paint or other
finishing materials.
b. Restore damaged pipe covering to its original condition.

3. Floors and Walls: Where walls or partitions that are removed extend one finished area
into another, patch and repair floor and wall surfaces in the new space. Provide an
even surface of uniform finish, color, texture, and appearance. Remove in-place floor
and wall coverings and replace with new materials, if necessary, to achieve uniform
color and appearance.

a. Where patching occurs in a painted surface, prepare substrate and apply primer
and intermediate paint coats appropriate for substrate over the patch, and apply
final paint coat over entire unbroken surface containing the patch. Provide
additional coats until patch blends with adjacent surfaces.

4. Ceilings: Patch, repair, or rehang in-place ceilings as necessary to provide an even-

plane surface of uniform appearance.
5. Exterior Building Enclosure: Patch components in a manner that restores enclosure to
a weathertight condition and ensures thermal and moisture integrity of building
enclosure.

I. Cleaning: Clean areas and spaces where cutting and patching are performed. Remove paint,
mortar, oils, putty, and similar materials from adjacent finished surfaces.

3.7 OWNERROYAL COMMISSION-INSTALLED PRODUCTS

A. Site Access: Provide access to Project site for OwnerRoyal Commission's construction
personnel.

B. Coordination: Coordinate construction and operations of the Work with work performed by
OwnerRoyal Commission's construction personnel.

1. Construction Schedule: Inform OwnerRoyal Commission of Contractor's preferred

construction schedule for OwnerRoyal Commission's portion of the Work. Adjust
construction schedule based on a mutually agreeable timetable. Notify OwnerRoyal
Commission if changes to schedule are required due to differences in actual
construction progress.
2. Preinstallation Conferences: Include OwnerRoyal Commission's construction
personnel at preinstallation conferences covering portions of the Work that are to
receive OwnerRoyal Commission's work. Attend preinstallation conferences
conducted by OwnerRoyal Commission's construction personnel if portions of the
Work depend on OwnerRoyal Commission's construction.

3.8 PROGRESS CLEANING Formatted: Font: 8 pt

Formatted: Font: 8 pt
A. General: Clean Project site and work areas daily, including common areas. Enforce
requirements strictly. Dispose of materials lawfully. Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 9 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
1. Comply with requirements in NFPA 241 for removal of combustible waste materials
and debris. Formatted: Font: 8 pt
2. Do not hold waste materials more than seven days during normal weather or three Formatted: Tab stops: 6.25", Right + Not at 6.5"
days if the temperature is expected to rise above 80 deg F (27 deg C).
3. Containerize hazardous and unsanitary waste materials separately from other waste.
Mark containers appropriately and dispose of legally, according to regulations.

a. Use containers intended for holding waste materials of type to be stored.

4. Coordinate progress cleaning for joint-use areas where Contractor and other
contractors are working concurrently.

B. Site: Maintain Project site free of waste materials and debris.

C. Work Areas: Clean areas where work is in progress to the level of cleanliness necessary for
proper execution of the Work.

1. Remove liquid spills promptly.

2. Where dust would impair proper execution of the Work, broom-clean or vacuum the
entire work area, as appropriate.

D. Installed Work: Keep installed work clean. Clean installed surfaces according to written
instructions of manufacturer or fabricator of product installed, using only cleaning materials
specifically recommended. If specific cleaning materials are not recommended, use cleaning
materials that are not hazardous to health or property and that will not damage exposed
surfaces.

E. Concealed Spaces: Remove debris from concealed spaces before enclosing the space.

F. Exposed Surfaces in Finished Areas: Clean exposed surfaces and protect as necessary to
ensure freedom from damage and deterioration at time of Substantial Completion.

G. Waste Disposal: Do not bury or burn waste materials on-site. Do not wash waste materials
down sewers or into waterways. Comply with waste disposal requirements in
[Section 015000 "Temporary Facilities and Controls."] [Section 017419 "Construction
Waste Management and Disposal."]

H. During handling and installation, clean and protect construction in progress and adjoining
materials already in place. Apply protective covering where required to ensure protection
from damage or deterioration at Substantial Completion.

I. Clean and provide maintenance on completed construction as frequently as necessary

through the remainder of the construction period. Adjust and lubricate operable components
to ensure operability without damaging effects.

J. Limiting Exposures: Supervise construction operations to ensure that no part of the

construction, completed or in progress, is subject to harmful, dangerous, damaging, or
otherwise deleterious exposure during the construction period.

3.9 STARTING AND ADJUSTING

Formatted: Font: 8 pt
A. Coordinate startup and adjusting of equipment and operating components with requirements
Formatted: Font: 8 pt
in Section 019113 "General Commissioning Requirements."
Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 10 of 11 017300 - 1Contract

No.
Copyright 2015 AIARoyal Commission - Yanbu MasterSpec PremiumExecution 09/15August 2016 Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
B. Start equipment and operating components to confirm proper operation. Remove
malfunctioning units, replace with new units, and retest. Formatted: Font: 8 pt
Formatted: Tab stops: 6.25", Right + Not at 6.5"
C. Adjust equipment for proper operation. Adjust operating components for proper operation
without binding.

D. Test each piece of equipment to verify proper operation. Test and adjust controls and
safeties. Replace damaged and malfunctioning controls and equipment.

E. Manufacturer's Field Service: Comply with qualification requirements in Section 014000

"Quality Requirements."

3.10 PROTECTION OF INSTALLED CONSTRUCTION

A. Provide final protection and maintain conditions that ensure installed Work is without
damage or deterioration at time of Substantial Completion.

B. Protection of Existing Items: Provide protection and ensure that existing items to remain
undisturbed by construction are maintained in condition that existed at commencement of
the Work.

C. Comply with manufacturer's written instructions for temperature and relative humidity.

END OF SECTION 017300

Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt
Formatted: Font: 8 pt

EXECUTION01 73 00 Page 11 of 11 017300 - 1Contract

No.