Downloaded from http://www.everyspec.

com

. . .

--

MIL-STD-1759
10JULY 1979

MILITARY STANDARD

RIVETS AND RIVET TYPE FASTENERS’

PREFERRED FOR DESIGN ,

LISTING OF

FSC 5320
/.+ # “f’
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

DEPARTMENT OF DEFENSE
Washington, DC 20301

Rivets and Rivet Type Fasteners Preferred For Design, Listing of:

MIL-STD-1759

1. This Military Standard is approved for use by all Departments and

Agencies of the Department of Defense.

2. Beneficial comments (recommendations, additions, deletions) and

any pertinent data which may be of use in improving this document
should be addressed to: Commander, Aeronautical Systems Division
(AFSC), ATTN: ASD/ENESS, Wright-Patterson Air Force Base, Ohio 45433 by
using the self-addressed Standardization Document Improvement Proposal
(DD Form 1426) appearing at the end of this document or by letter.

ii

....
)
 Downloaded from http://www.everyspec.com

,.

-L
MIL-STII-1759
10JULY 1979

FOREWORD

1. The purpose of th~s bookform standard is to provide a commodity

type parts document on rwets and rivet type fasteners to aid military
equipment designers and engineers in the selection of preferred rivets
and rivet type fasteners.

2* This document consists of an jndex of preferred standardization

documents and a listing of preferred parts within these documents that
have been selected with respect to configuration, sizes, lengths,
materials, and finishes for rivets and rivet type fasteners.

3. The selection of preferred documents listed in this standard and

the selection of part numbers within the preferred documents were made
as follows:

a. Selection of Documents

(1) Documents listed or scheduled for listing in the

Department of Defense Index of Specifications and Standards (DODISS).

(2) Documents which are active for design.

L
(3) Documents specifying part numbers (dash numbers) which
designate specific sizes, materials and finishes.

b. Selection of Part Numbers

(1) By conducting a thorough search and evaluation of

existing DoD procurement information.

(2) By evaluation of preferred parts listed in recent weapon

system contracts.

(3) By evaluation of preferred parts 1ists obtained from

industry. ●

4. To increase the scope and versatility of this rivets and rivet

type fasteners standard, periodic revisions will be developed, Results
from Standardization studies, MILITARY PARTS CONTROL ADVISORY GROUP
(MPCAG) evaluations, evaluation of @ new family of rivets and rivet
type fasteners and recommendations from interested activities will form
the basis for these revisions.

iii
/--/)
 Downloaded from http://www.everyspec.com

--., . .

MIL-STD-1759
10 JULY 1979

CONTENTS

Page

Paragraph 1. SCOPE ---------------------------------- 1

2. REFERENCED DOCUMENTS------------------- 2-13

3. DEFINITIONS---------------------------- 13-14

4. GENERAL STATEMENTS ---------------------14-15

5. DETAILED REQUIREMENTS------------------15

6. NOTES ---------------------------------- 15

SECTIONS

Section 100 CAP, RIVET

101 Caps, Rivet ----------------------------------101.1

200 COLLAR, GROOVED, PIN-RIVET

201 Collar Hi-Shear Rivet, 1200°F----------------201.1

202 Collar (High Strength) High-Shear Rivet------2O2.l

203 Collar, Swage Locking for Pull-Type

and Stump-Type Lockbolts---------------------2O3,1

204 Collar, Swage-Locking; Regular Height,

Flanged and Low Profile, Aluminum Alloy,
Corrosion Resistant Steel, Carbon Steel and
Alloy Steel----------------------------------204.1

300 COLLAR, PIN-RIVET, THREADED

301 Nut, Crimp, For Crimplock Fastener System----3ll.l

302 Nut, Extended Washer, Hexagon-Self-Locking,

Low Height, C’ Bore --.-.---------------------302.1

303 Nut, Hex and Washer, Self-Aligning, Self-

Locking-Shear Pin----------------------------303.1

304 Pin-Rivet Collar, Threaded, Torque-Off, Self-

Locking .--------------------.---------------- 304.1

.. .
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTIONS - Continued

Paqe

Section 305 Pin-Rivet Collar, Threaded, Torque-Off, Self-

Locking (Double Hex) --------------------------- 305.1.

400 PIN-RIVET, GROOVED

401 Bolt-Lock, Shear, 100° Head, Pull-Type, Titanium

Alloy ------------------------------------------ 401.1

402 Bolt-Lock, Shear, 100° Head, Stump-Type,

Titanium Alloy -------------- ------------------- 402.1

403 Bolt-Lock, Shear, Protruding Head, Pull-Type,

Titanium Alloy ------- -------------------------- 403.1

404 Bolt-lock, Shear, Protruding Head, Stump-Type,

Titanium Alloy -------------- ------------------- 404 1 ●

405 Bolt-Lock, Tension, 100° Crown Head, Pull-Type

Titanium Alloy ----------“---------------------- 405.1
-
406 Bolt-Lock, Tension, 100° Crown Head, Stump-Type,
Titanium Alloy --------------.------------------ 406.1

407 Bolt-Lock, Tension, 100° Head (MS20426), Pull-

Type, Titanium Alloy --------------------.------ 407.1

408 Bolt-Lock, Tension, 100° Head (MS20426), Stump-

Type, Titanium Alloy --------------------------- 408.1

409 Bolt-Lock, Tension, 100° Head (MS24694), Pull-

Type, Titanium Alloy --------------------------- 409 1
●

410 Bolt-Lock, Tension, 100° Head (MS24694), Stump-

Type, Titanium Alloy ---------------- ----------- 410.1

411 Bolt-Lock, Tension, Protruding Mead, Pull-Type,

Titanium Alloy -------------- ------------------- 411.1

412 Bolt-Lock, Tension, Protruding Head, Stump-Type,

Titanium Allov --------------------.-----.------ 412.1
“

v
 Downloaded from http://www.everyspec.com

MIL-STD”1759
10 JULY 1979
SECTIONS - Continued

Paqe

Section 413 Pin, Swage Locking, A-286 CRES, 100° Head

(MS20426), Tension, pU1l-TYPe------------------ 41301

414 Pin, Swage Locking, A-286 CRES, 100° Head

(MS24694), Tension, Pull-Type------------------ 4:4,1 ~

415 Pin, Swage Locking, A-286 CRES, 100° Shear Head,

Stump-Type --------------0---------------------- 415.1

416 Pin, Swage Locking, A-286 CRES, 100° Shear/

Tension Head, Pull-Type ------------------------ 416.1

417 Pin, Swage Locking, A-286 CRES, Protruding Head,

Shear/Tension, Pull-Type----------------------- 417.1

418 Pin, Swage Locking, A-286 CRES, Protruding Head,

Shear, Stump-Type ----------------------------.- 418.1

419 Pin, Swage Locking, A-286 CRES, Protruding Head,

Tension, Pull-Type ------- .--------------------- 419.1

420 Pin, Swage Locking, 108 KSI Steel, 100° Shear/

Tension Head, Pull-Type ------------------------ 420.1

421 Pin, Swage Locking, 108 KSI Steel, Protruding

Head, Shear/Tension, Pull-Type----------------- 421el

422 Pin, Swage Locking, Aluminum Alloy, 100° Head

(MS20426), Tension, Pull-Type------------------ 422.1

423 Pin, Swage Locking, Aluminum Alloy, 100° Head

(MS24694), Tension, Pull-Type------------------ 423.1

424 Pin, Swage Locking, Aluminum Alloy, 100° Head

(MS20426), Tension, Stump-Type----------------- 4240~

425 Pin. Swaqe Locking, Aluminum Alloy, Protruding ___ _

Head, Te;sion, Pull-Type----------------------- 425,1

426 Pin, Swage Locking, Aluminum Alloy, Protruding

Head, Tension, Stump-Type ---------------------- 426,1

-
 Downloaded from http://www.everyspec.com

.
,

-..

>.- P’lIL-sT’D-1759
10JULY 1979

SECTIONS - Continued

Paqe

Section 427 Pin, Swage-locking, Brazier Head, Straight

Shank, Six Locking Grooves. Aluminum Alloy,
Corrosion Resistant Steel and Carbon Steel----- 427.1

428 Pin, Swage-locking, Button Head, Straight

Shank, Six Locking Grooves and Mult~ple Locking
Grooves. Aluminum Alloy, Corrosion Resistant
Steel and Carbon Steel ------------------------- 428.1

429 Pin, Swage-locking, Flat 90° Countersunk Head,

Straight Shank, Six Locking Grooves and Multiple
Locking grooves. Aluminum Alloy, Corrosion
Resistant Steel and Carbon Steel--------------- 429.1

430 Pin, Swage-locking, Oval 60° Countersunk Head,

Tapered-Section Shank, Multiple Locking Grooves.
Aluminum Alloy, Corrosion Resistant Steel and
Carbon Steel ----.------------------------------ 430.1

431 Pin, Swage Locking, Steel, 100° Crown Head,

Tension, Pull-Type ----------------------------- 431.1

432 Pin, Swage Locking, Steel, 100° Head (MS20426)

Tension, Stump-Type -.-------------------------- 432.1

433 Pin, Swage Locking, Steel, 100° Shear Head,

Stump-Type ------------------------------------- 433,1

434 Pin, Swage Locking, Steel, Protruding Head,

Shear, Stump-Type ------------------------------ 434.1

435 Pin, Swage Locking, Steel, protrudin9 Heads

Tension, Stump-Type -----0- --------------------- 435.1

436 Pin, Swage Locking, Steel, 100° Head (MS20426),

Tension, Pull-Type ------- ---------------------- 436.1

437 Pin, Swage Locking, Steel, 100° Head (MS24694),

Tension, Pull-Type ----------------------------- 437.1

vii
 Downloaded from http://www.everyspec.com
.

&

MIL-STD-1759
10JULY 1979

SECTIONS - Continued

Page

Section 438 Pin, Swage Locking, Steel, 100° Shear Head,

Pull-Type -------------------------------------- 438.1

439 Pin, Swage Locking, Steel, Protruding Head, Shear,

Pull-Type -------------------------------------- 439.1

44o Pin, Swage Locking, Steel, Protruding Head, Shear,

Pull-Type -------------------------------------- 440.1

441 Pin, Swage-Locking, Truss Head, Straight Shank,

Six Locking Grooves and Multiple Locking Grooves.
Aluminum Alloy, Corrosion Resistant Steel and
Carbon Steel ----------------------------------- 441.1

442 Pin, Swage Locking, Washer Face, Brazier

Head, Straight Shank, Six Locking Grooves.
Corrosion Resistant Steel---------------------- 442.1

500 PIN-RIVET, THREADED

501 Pin, Crimp, 100° Crown Shear/Tension Head------ 501.1

502 Pin, Crimp, 100° FIush Shear Head-------------- 502”1

503 Pin, Crimp, Protruding Shear Head-------------- 503.1

504 Pin, Crimp, Protruding Tension Head------------ 504.1

505 Pin-Rivet, Threaded, Button Head! Strai9ht

Shank-------------- ------.--------------------- 505.1

506 Pin-Rivet, Threaded, Button Head, Tapered

Shank------------------------------------------ 506.1

507 Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Shank --------------------.--------------------- 507.1 .

508 Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Tapered Shank ---------------------------------- 508.1

viii

*
r,
 Downloaded from http://www.everyspec.com

.
.

-. .-
.:,

--
MIL-STD-1759
10JULY 1979

SECTIONS - Continued

Paue

Section 509 Pin-Rivet, Threade”d, 90° Countersunk Flat Head,

Straight Shank --------------------------------- 509 1
●

510 Pin-Rivet, Threaded, Nail Head, Straight Shank,

Corrosion Resistant Steel---------------------- 510.1

511 Pin-Threaded Shear 100° CSK Head--------------- 511.1

512 Pin-Threaded Shear Protruding Head------------- 512.1

600 RIVET, BLIND

601 Fastener, Blind, High Strengt$ pull Type,

Positive Mechanical Lock, 100 Flush Head,
Corrosion Resisting Steel 95 KSI FLU----------- 601.1

602 Fastener, Blind, High Strength, pull Type,

Positive Mechanical Lock~ protrudin9 Heads
Corrosion Resisting Steel 95 KSI Fsu----------- 602.1

603 Fastener-Blind, Internally Threaded, External

Sleeve, Flush Head, Self-Locking --------------- 603,1

604 Fastener-Blind, Internally Threaded, External

sleeve, Protruding Head> Self-Locking---------- 604*1

605 Fastener-Blind, Internally Threaded, External

Sleeve, Lightweight, Millable Head, Self-
Locking ------- --------------------------------- 605.1

606 Rivet, Blind-Countersunk Head, Drive Type------ 606.1

607 Rivet-Blind, 100° Flush Head, Locked Spindle--- 607.1

608 Rivet-Blind, 100° Flush Head,”Mechanically

------------------------- 608 1
Locked Spindle, IMbed ●

;Y
 Downloaded from http://www.everyspec.com
.

.:

MIL-sTll”1759
10 JULY 1979

SECTIONS - Continued

Page

%ctiom 609 Rivet, Blind-General Purpose, Bulbed, 100°

Flush Head, Mechanically-Locked-Spindle-------- 609.1

610 Rivet, Blind-General Purpose, Bulbed, Protrud-

ing Head, Mechanically-Locked-Spindle---------- 610.1

611 Rivet$ Blind, High Strength, gull Type,

Positive Mechanical Lock, 100 Flush Head,
Alloy Steel 112 KS1 Flu------------------------ 611.1

612 Rivet, Blind, High Strength, Pull Type,

Positive Mechanical Lock, Protruding Head,
Alloy Steel 112 KSI Flu------------------------ 612.1

613 Rivet, Blind, Nonstructural, 100° Flush Head,

Class 2-----------------------.---------------- 613.1

614 Rivets, Blind, ljonstructural, Retained Mandrel;

Closed-End, 120 Countersunk Head; Aluminum
Al 1Oy------------------------------------------ 614.1

615 Rivets, Blind, Nonstructural, Retained Mandrel;

Closed-End, Domed Head; Aluminum Alloy--------- 6.1~.l

816 Rivets, Blindd Nonstructural, Retained Mandrel;

Open-End, 100 Countersunk Head; Aluminum
Alloy ----“------------------------------------- 616.1

617 Rivets, Blindb Nonstructural, Retained Mandrel;

Open-End, 120 Countersunk Head; Aluminum
Alloy -----d------------------------------------ 617.1

618 Rivets, Blindd Nonstructural, Retained Mandrel;

Open-End, 120 Countersunk Head; Aluminum
Alloy, Carbon Steel, Nickel-Copper Alloy ------- 618.1
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

SECTIONS - Continued

Page

Section 619 Rivets, Blind, Nonstructural, Retained Mandrel;

Open-End, Domed Head; AIuminum Alloy----------- 619*1

620 Rivets, Blind, Nonstructural, Retained Mandrel;

Open-End, 3D Domed Head; Aluminum Alloy, Carbon
Steel ------..------------------0--------------- 620.1

621 Rivets, Blind, Nonstructural, Retained Mandrel;

open-End, Domed Head; Aluminum Alloy, Carbon
Steel, Corrosion Resistant Steel --------------- 621.1

622 Rivets, Blind, Nonstructural, Retained Mandrel;

Open-End, Domed I-1ead;
Nickel-Copper Alloy------ 622.1

623 Rivets, Blind, Nonstructural, Retained Mandrel;

Open-End, Snap Head; Aluminum Alloy------------ 623.1

624 Rivet, Blind, Nonstructural, Universal Head,

..
Class I-.-------------------------------------- 624.1

625 Rivet-Blind, Protruding I-1ead,Locked Spindle--- 625.1

626 Rivet-Blind, Protruding Head, Mechanically

Locked Spindle, Bulbed ------------------------- 626.1

627 Rivet, Blind,oStructural, Pull Stem, Self-

Plugging, 100 Flush Head, TypeII, Class 2---- 627.1

628 Rivet, Blind, Structural, Pull Stem, Self-

plugging, Protruding Head, Type I-------------- 628,1,

629.1
629 Rivet, Bli~d-Universal Head, Drive Type --------

700 RIVET, SOLID

701 Pin, 100° &SK Head Hi-shear Rivet, Close Toler-

ance, 1200 F--------- ------------------ ------- 701.1

702 Pin,oFlat Head Hi-Shear Rivet, Close Tolerance,

1200 F-------” ----.---------------------------- 702.1

\-
 Downloaded from http://www.everyspec.com
.

=...

--
MIL-STD-1759
10 JULY 1979

SECTIONS - Continued

Paqe

Section 703 Rivet-lOOO Countersunk Head Corrosion Resistant

Steel.------.--”------------------------------- 703.1

704 Rivet-lOOO Countersunk Head Hi-Shear Close

Tolerance Head and Shank----------------------- 704.1

705 Rivet-lOOO Countersunk Head, Mild Steel-------- 705.1

706 Rivet-Flat Head, Hi-Shear, Close Tolerance

Shank------------------------------------------ 706.1

707 Rivet, Solid-Belt ------------------------------ 707.1

708 Rivet, Solid, Button Head, Steel--------------- 708.1

709 Rivet, Solid-lOOO Countersunk Head, Carbon Steel,

Corrosion-Resistant Steel, Model--------------- 709.1

710 Rivet, Solid, Countersunk 100°, Precision Head,

Aluminum and Aluminum Alloy-------------------- 710.1 -

711 Rivet, Solid-Countersunk Head, Brass or Copper- 711.1

712 Rivet-Solid-lOOO Flush Head A286 Corrosion

Resistant Steel-.-----------------.------------ 712.1

- 713 Rivet, Solid, 100° Flush Head, AMS 7229-------- 713.1

714 Rivet, Solid, 100° Flush Head, AMS 7232-------- 714.1

715 Rivet, Solid-lOOO Flush Head, AMS 7233--------- 715.1

716 Rivet, Solid-lOOO Flush Head, AMS 7235--------- 716.1

717 Rivet,.Solid, 100° Flush Shear Head A286

Corrosion Resistant Steel and Model------------ 717.1

718 Rivet, Solid-lOOO Flush Shear Head, Aluminum

Al10y- -- -- ---- - - -- -- - - -- -- -- -- -- -- - --- - - -- - - - - - 718.1

719 Rivet, Solid-Small, Countersunk Head, Steel,

Annealed --------------------------------------- 719.1

720 Rivet, Solid-Small, Pan Head, Steel, Annealed-- 720.1

-

xii
.. n ‘“
 Downloaded from http://www.everyspec.com

. .

---
MIL-STD-1759
10JULY 1979

SECTIONS - Continued

Page

Section 721 Rivet, Solid-Tinner’s --.---------.------------- 721.1

722 Rivet, Solid-Universal Head, Aluminum and

Aluminum Alloy --------------------------------- 722.1

723 Rivet-Solid Universal Head, A286 Corrosion

Resistant Steel -------------------------------- 723.1

724 Rivet, Sol id-Universal Head, AMS 5737---------- 724.1

..
725 Rivet, Solid, Universal Head, AMS 7229--------- 725.1

726 Rivet, Solid, Universal Head, AMS 7232--------- 726.1

727 Rivet, Titanium, Bimetal, 95 KSI Fsu, 100° Full

Flush, Crown Head, Type II--------------------- 727.1

728 Rivet, Titanium, Bimetal, 95 KSI Fsu,

Protruding Head, Type I------------------------ 728.1

729 Rivet, Titanium, Bimetal, 95 KSI Fsu, 100°

Reduced Flush Crown Head, Type III------------- 729.1

800 RIVET, SPLIT

801 Rivet, Split-Oval Head------------------------- ~olel

900 RIVET, TUBULAR

901 Rivet-Tubular, 150° Flat Countersunk Head------ 901.1

902 Rivet, Tubular-Flat Head----------------------- 902.1

903 Rivet-Tubular, Oval Head----------------------- 903.1

xiii
Downloaded from http://www.everyspec.com

--
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

1, SCOPE

1.1 Scope. This standard provides a listing of preferred rivets and

rivet type fasteners encompassing the following characteristics:

a. Configuration .

b. Size ~

c. Materials

d. Protective Coatings and Finishes

1.2 Purpose. The purpose of this standard is as follows:

a. provide the designer with a listing of preferred rivets and

rivet type fasteners to promote their use in design of weapon systems
and equipments. .

b. control and minimize the variety of rivets and rivet type

fasteners used in military equipment thereby facilitating logistic
support of the equipment during its life cycle.

1.3 Application. To minimize the proliferation of rivets and rivet

type fasteners only the preferred part numbers. listed herein are author-
ized for use in new design. All other part numbers, even though shown
on current Military Specification Sheets, Military Standards (MS),
National Aerospace Standards (NAS), Aeronautical Standards (AS), and
Air Force/Navy Aeronautical Standards (AN), are not approved for use in
new design unless approved by the cognizant Government procuring
activity.

1.4 Intended use. Implement this standard by including one of the

following options in the contract:

Require this s~andard as a supplement to an end use type

standar~”such as MIL-STD-1471 or MIL-STD-1515. When thus required, only
the rivets and rivet type fasteners listed in both the end use type and
this standard are acceptable. Use of other rivets and rivet type fas-
teners requires approval of the Government procuring activity.

b. Require this standard as a guide to be used with an end

use type standard such as MIL-STD-1471 or MIL-STD-1515. When thus
required, the rivets and rivet type fasteners listed in the end use
type standard and this standard are acceptable. The designer must
assure himself the rivets and rivet type fasteners listed in both the
 .
Downloaded from http://www.everyspec.com

.- -.
-:..

MIL-STD-1759 --
10JULY 1979

end use type standard and this standard are not adequate for his
requirement before using rivets and rivet type fasteners not listed
. herein. Use of rivets and rivet type fasteners not listed in the end
use type standard requires approval of the Government procuring activity.

Require this standard and indicate exceptions to it. When

.
thus re~;ired, only the rivets and rivet type fasteners listed in this
standard and not excluded by the exceptions are acceptable. Use of
other rivets and rivet type fasteners requires approval of the Govern- ‘
ment procuring activity.

d. Require this standard as a guide. When thus required, the

designer must assure himself the rivets and rivet type fasteners listed
in this standard are not adequate for the requirement before using
other rivets and rivet type fasteners.

2. REFERENCED DOCUMENTS

2.1 Issues of documents. The following documents of the issue in

effect on date of invitation for bids or request for proposal form a
part of this standard.to the extent specified herein.

SPECIFICATIONS

MILITARY

MIL-P-23469/l - Collar, Swage-Locking; Regular Height, Flanged and

Low Profilei Aluminum Alloy, Corrosion Resistant
Steel, Carbon Steel and Alloy Steel.

MIL-P-23469/2 - Pin, Swage-Locking, Brazier Head, Straight Shank,

Six Locking Groove. Aluminum Alloy, Corrosion
Resistant Steel and Carbon Steel.

MIL-P-23469/3 - Pin, Swage-Locking, Washer Face, Brazier Head,

Straight Shank, Six Locking Grooves. Corrosion
Resistant Steel.

MIL-P-23469/4 - Pin, Swage-Locking, Button Head, Straight Shank, Six

Locking Groove and Multiple Locking Groove.
Aluminum Alloy, Corrosion Resistant Steel and Carbon
Steel.

MIL-P-23469/5 - Pin, Swage-Locking, Truss Head, Straight Shank,

Six Locking Groove and Multiple Locking Groove.
Aluminum Alloy, Corrosion Resistant Steel and Carbon
Steel .

-
.
Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SPECIFICATIONS

MILITARY - Continued

MIL-P-23469/6 - Pin, Swage-Locking, Flat 90° Countersunk Head,

Straight Shank, Six Locking Groove and Multiple -
Locking Groove. Aluminum Alloy, Corrosion Resistant
Steel and Carbon Steel.

MIL-P-23469/7 - Pin, Swage-Locking, Oval 60° Countersunk Head,

Tapered-Section Shank, Multiple Locking Grooves.
Aluminum Alloy, Corrosion Resistant Steel and Carbon
Steel.

MIL-P-23470/l - Pin-Rivet, Threaded, Button Head, Straight Shank,

Corrosion Resistant Steel.

MIL-P-23470/2 - Pin-Rivet, Threaded, Button Head, Tapered Shank,

Corrosion Resistant Steel.

MIL-P-23470/3 - Pin-Rivet, Threaded, Nail Head, Straight Shank,

Corrosion Resistant Steel.

MIL-P-23470/4 - Pin-Rivet, Threaded> 90° Countersunk, Flat Head,

Straight Shank, Carbon Steel.

MIL-P-23470/5 - Pin-Rivet, Threaded, Button Head, Straight Shank,

Carbon Steel.

MIL-P-23470/6 - Pin-Rivet, Threaded, Button Head, Tapered Shank,

Carbon Steel.

MIL-P-23470/7 - Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Straight Shank, Carbon Steel.

MIL-P-23470/8 - Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Tapered Shank, Carbon Steel.

MIL-P-23470/9 - Pin-Rivet, Threaded, 90° Countersunk, Flat Head,

Straight Shank, Corrosion Resistant Steel.

MIL-P-23470/10 - Pin-Rivet, Threaded, Button Head, Straight Shank,

Corrosion Resistant Steel.

MIL-P-23470/11 - Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Straight Shank, Corrosion Resistant Steel.
 Downloaded from http://www.everyspec.com

. .

-
MIL-STD-1759
10JULY 1979

SPECIFICATION

MILITARY - Continued

MIL-P-23470/12 - Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Tapered Shank, Corrosion Resistant Steel. ~

MIL-P-23470/13 - Pin-Rivet, Threaded, 90° Countersunk Flat Head, “

Straight Shank, Aluminum Alloy.

MIL-P-23470/14 - Pin-Rivet, Threaded, Button Head, Straight Shank,

Aluminum Alloy.

MIL-P-23470/15 - Pin-Rivet, Threaded, Button Head, Tapered Shank,

Aluminum Alloy.

MIL-P-23470/16 - Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Straight Shank, Aluminum Alloy.

MIL-P-23470/17 - Pin-Rivet, Threaded, 60° Countersunk Oval Head,

Tapered Shank, Aluminum Alloy.

MIL-P-23470/18 - Pin-Rivet Collar, Threaded, Torque-off, Self-Locking,

Carbon Steel.

MIL-P-23470/19 - Pin-Rivet Collar, Threaded, Torque-off, Self-Locking,

Carbon Steel (Double Hex).

MIL-P-23470/20 - Pin-Rivet Collar, Threaded, Torque-off, Self-Locking,

Corrosion Resistant Steel.

MIL-P-23470/21 - Pin-Rivet Collar, Threaded, Torque-off, Self-Locking,

Corrosion Resistant Steel (Double Hex).

MIL-P-23470/22 - Pin-Rivet Collar, Threaded, Torque-off, Self-Locking,

Aluminum Alloy.

MIL-P-23470/23 - Pin-Rivet Collar, Threaded, Torque-off, Self-Locking,

Aluminum Alloy (Double Hex).

MIL-R-24243/l - Rivets, Blind, Nonstructural, Retained Mandrel; Open-

End, Domed Head; Aluminum Alloy, Carbon Steel,
Corrosion Resistant Steel.

MIL-R-24243/2 - Rivets, Blind, Nonstructural, Retained Mandrel; Open-

End, Domed Head; Nickel-Copper Alloy.

, 4
 Downloaded from http://www.everyspec.com

141L-STD-1759
10 JULY 1979

SPECIFICATIONS

MILITARY - Continued

MIL-R-24243/3 - Rivets, Blind, Nonstructural, Retained Mandrel; Open-

End, 3 D Domed Head; Aluminum Alloy, Carbon Steel.

MIL-R-24243/4 - Rivets, Blind, Nonstructural, Retained Mandrel; Open-

End, 100 Countersunk Head; Aluminum Alloy.

FIIL-R-24243/5 - Rivets, Blind, Nonstructural, Retained Mandrel; Open-

End, 120 Countersunk Head; Aluminum Alloy, Carbon
Steel, Nickel-Copper Alloy.

MIL-R-24243/6 - Rivets, Blind, Nonstructural, Retained Mandrel;

Closed-End, Domed Head; Aluminum Alloy.

MIL-R-24243/7 - Rivets, Blind, ~onstructural, Retained Mandrel;

Closed-End, 120 Countersunk Head; Aluminum Alloy.

MIL-R-24243/8 - Rivets, Blind, Nonstructural, Retained Mandrel;

Open-End, Snap Head; Aluminum Alloy.

MIL-R-24243/9 - Rivets, Blindd Nonstructural, Retained Mandrel;

Open-End, 120 Countersunk Head; Aluminum Alloy.

MIL-R-24243/10 - Rivets, Blind, Nonstructural, Retained Mandrel;

Open-End, Domed Head; Aluminum Alloy.

MIL-R-83459/l - Rivet, Titanium, Bimetal, 95 I(SIFsu, Protruding

Head, Type I.

MIL-R-83459/2 - Rivet, Titanium, Bimetal ,95 KSI Fsu, 100° Full

Flush, Crown Head, Type 11,

MIL-R-83459/3 - Ri~et, Titanium; Bimetal, 95 KSI Fsu, 100”

Reduced Flush Crown Head, Type 111

STANDARDS

MILITARY .

MS9318 - Rivet, Solid-lOOO Flush Head, AMS7233.

MS9403 - Rivet, SolId-Universal Head, AMS5737.

 Downloaded from http://www.everyspec.com

.:

--
MIL-STD-1759
10 JULY 1979

STANDARDS

MILITARY - Continued

MS9460 - Rivet, Solid-lOOO Flush Head, AMS7235.

MS16535 - Rivet-Tubular, Oval Head.

MS16536 - Rivet-Tubular, 150° Flat Countersunk Head.

MS20426 - Rivet, Solid, Countersunk 100°, Precision Head,

Aluminum and Aluminum Alloy.

MS20427 Rivet, Solid-lOOO Countersunk Head, Carbon Steel,

Corrosion-Resistant Steel, Monel and Copper.

MS20470 - Rivet, Solid-Universal Head, Aluminum and Aluminum

Alloy.

MS20600 Rivet, Blind, Structural, Pull Stem, Self-Plugging,

Protruding Head, Type 11, Class 1.

MS20601 Riv t, Blind, Structural, Pull Stem, Self-Plug9in99

t
100 Flush Head, Type I.

MS20604 Rivet, Blind, Nonstructural, Universal Head,

Class I. ~

MS20605 Rivet, Blind, Nonstructural, 100° Flush Head,

Class 2.

MS20613 Rivet, Solid-Universal Head, Steel, Carbon, and Steel,

Corrosion-Resistant.

MS20615 - Rivet, Solid-Universal Head, Brass, Copper and Nickel-

Copper Alloy. .

MS21140 - Fastener, Blind, Hig~ Strength, Pull Type, Positive

Mechanical Lock, 100 Flush Head, Corrosion
Resisting Steel 95 KSI Fsu.

MS21141 Fastener, Blind, High Strength, Pull Type,

Positive Mechanical Lock, Protruding Head,
Co~rosion Resisting Steel 95 KSI Fsu.

MS24661 - Rivet, Blind-Countersunk Head, Drive Type.

6
 Downloaded from http://www.everyspec.com

.:

----
MI L-STD-1759
i3 ,IIIL’{
1979

STANDARDS

MILITARY - Continued

MS24662 - Rivet, Blind-Universal Head, Drive Type.

MS35684 - Rivet, Split-Oval Head, Steel.

MS35685 - Rivet, Split-Oval Head, Brass.

MS35743 Rivet, Solid-Small, Pan Head, Steel, Annealed.

MS35744 Rivet, Solid-Small, Countersunk Head, Steel,

Annealed.

MS35745 - Rivet, Solid-Belt.

MS51829 .- Rivet$ Solid, Button Head, Steel.

MS51924 - Caps, Rivet.

MS51931 - Rivet, Solid-Tinner’s.

MS51942 - Rivet, Tubular-Flat l-lead.

MS51945 Rivet, Solid-Countersunk Head, Brass or Copper.

MS90353 Rivet, Blind, High S&rength, pull Type, Positive

Mechanical Lock, 100 Flush Head, Alloy Steel 112
KSI FSU.

MS90354 Rivet, Blind, High Strength, Pull Type, Positive

Mechanical Lock, Protruding Head, Alloy Steel 112
KSI FSU.
.
AIR FORCE - NAVY AERONAUTICAL

AN123151 thru AN123300 - Rivet, Solid, Universal Head, AMS7229.

AN123301 thru AN123450 - Rivet, Solid, Universal Head, AMS7232.

AN123451 thru AN123600 - Rivet, Solid, 100° Flush I-1ead,

AMS7229.

AN123601 thru AN123750 - Rivet, Solid, 100° Flush Head, AMS7232.

AN124951 thru AN1251OO - Rivet-lOO” Countersunk Head Corrosion

Resistant Steel.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

(Copies of specifications, standards, drawings, and publications re-

quired by contractors in connection with specific procurement functions
should be obtained from the procuring activity or as directed by the
contracting officer.)

2.2 Other publications, The following documents form a part of this

standard to the extent specified herein. Unless otherwise indicated,
the issue in effect on date of invitation for bids or request for pro=
posal apply.

AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC.(AIA)

NATIONAL AEROSPACE STANDARDS

NAS525 Rivet-lOOO Countersunk Head Hi-Shear Close

Tolerance Head and Shank.

NAS528 Collar (High Strength) High-Shear Rivet.

NAS529 Rivet-Flat Head, Hi-Shear, Close Tolerance

Shank.

NAS108O Collar, Swage Locking for Pull-Type and Stump

Type Lockbolts. -

NAS1097 Rivet, Solid-lOOO Flush Shear Head-,Aluminum

Alloy.

NAS1198 Rivet-Solid Universal Head, A286 Corrosion

Resistant Steel.

NAS1199 Rivet, Solid-lOO” Flush Head A286 Corrosion

Resistant Steel.

NAS1200 Rivet, Solid, 100° Flush Shear Head A286

Corrosion Resistant Steel and Monel.

NAS1287 Nut, Extended Washer, Hexagon-Locking,

LOW Height, C’ Bore.

NAS1288 Nut, Hex and Washer, Self-Aligning, Self-

Locking-Shear Pin.

NAS1292 thru NAS1296 Pin-Threaded Shear 100° CSK Head.

NAS1322 thru NAS1326 Pin-Threaded Shear Protruding Head.

-
 Downloaded from http://www.everyspec.com

.:.

...-

MIL-STD-1759
10 JULY 1979

AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. (AIA)

NATIONAL AEROSPACE STANDARDS - Continued

NAS1398 Rivet-Blind, Protruding Head, Locked Spindle.

NAS1399 Rivet-Blind, 100° Flush Head, Locked Spindle.

NAS1414 thru NAS1422 Pin, Swage Locking, Steel, 100° Shear Head,
Stump-Type.

NAS1424 thru NAS1432 Pin, Swage Locking, Steel, protrudin9 Heads

Shear, Stump-Type.

NAS1436 thru NAS1442 Pin, Swage Lo~king, Steel, Standard and

Oversize, 100 Shear HeadA,Pull-Type.

NAS1446 thru NAS1452 Pin, Swage Locking, Steel, Standard and

Oversize, Protruding Head, Shear, Pull-Type.

NAS1456 thru NAS1462 Pin, Swage Lo~king, Steel, Standard and

Oversize, 100 Head (MS24694), Tension, Pull-
Type.

NAS1465 thru NAS1472 Pin, Swage Locking, Steel, Standard and

Oversize, Protruding Head, Tension, Pull-
Iype.

NAS1475 thru NAS1482 Pin, Swage Lo king, Steel, Standard and

8
Oversize, 100 Head (MS20426), Tension, Pull-
Type.

NAS1486 thru NAS1492 Pin, Swage Locking, Steel, 100° Head (MS24694),
●
Tension, -Stump-Type.

NAS1496 thru NAS1502 Pin, Swage Locking, Steel, Protruding Head,

Tension, -Stump-Type.

NAS1516 thru NAS1522 Pin, Swage Locking, Aluminum Alloy, 100° Head
(FlS24694),Tension, Pull-Tupe.

NAS1525 thru NAS1532 Pin, Swage Locking, Aluminum Al oy, Protruding

Head, Tension, Pull-Type.

NAS1535 thru NAS1542 Pin, Swage Locking, Aluminum Al oy, 100° Head
(MS20426), Tension, Pull-Type.
 Downloaded from http://www.everyspec.com
.

MI L-STD-1759
10JULY 1979

AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. (AIA)

NATIONAL AEROSPACE STANDARDS - Continued

NAS1555 thru NAS1562 - Pin, Swage Locking, Aluminum Alloy, Protruding

Head, Tension, Stump-Type.

NAS1583 . pjn, 100° CSK H~ad Hi-Shear Rivet, ClOSe

Tolerance, 1200 F.

NAS1584 .- Pin, Flat Head Hi-Shear Rivet, Close Tolerance

1200°F.

NAS1585 “ - Collar Hi-Shear Rivet, 1200°F.

NAS1669 - Fastener-Blind, Internally Threaded, External

Sleeve, General Purpose, Protruding Head, Self-
Locking. ~

NAS1670 Fastener-Blind, Internally Threaded, External

Sleeve, General Purpose, Flush Head, Self-
Locking.

NAS1671 Fastener-Blind; Internally Threaded, External -

Sleeve, High Temperature, Protruding Head
Self-Locking.

NAS1672 - Fastener-Blind, Internally Threaded, External

Sleeve, High Temperature, Flush Head, Self-
Locking.

NAS1673 Fastener-Blind, Internally Threaded, External

Sleeve, Lightweight, Protruding Head, Self-
Locking.

NAS1674 Fastener-Blind, Internally Threaded, External

Sleeve, Lightweight, Millable Head, Self-Locking.

NAS1738 - Rivet-Blind, Protruding Head, Mechanically

Locked Spindle, Bulbed.

NAS1739 Rivet-Blind, 100° Flush Head, Mechanically

Locked Spindle, Bulbed.

NAS1919 Rivet, Blind-General Purpose, Bulbed, protrud-

ing Head, Mechanically-Locked-Spindle.

10
 Downloaded from http://www.everyspec.com

..-.-
MIL-STD-1759
10 JULY 1979

AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. (AIA)

NATIONAL AEROSPACE STANDARDS - Continued

NAS1921 - Rivet, Blind-General Purpose, Bulbed, 100°

Flush Head, Mechanically-Locked-Spindle.

NAS2005 thru NAS2012 - Bolt-Lock, Tension, Protruding Head, Standard

and Oversize, Pull-Type, Titanium A11oY.

NAS2105 thru NAS2112 - Bolt-Lock, Tension, 100° Head (MS24694), Pull-

Type, Titanium Alloy.

NAS2115 thru NAS2122 - Bolt-Lock, Tension, 100° Head (MS20426),

Standard and Oversize, Pull-Type, Titanium
Alloy.

NAS2125 thru NAS2132 - Bolt-Lock, Tension, 100° Crown Head, Standard

and Oversjze, Pull-Type, Titanium Alloy.

NAS2205 thru NAS2212 - Bolt-Lock, Tension, Protruding Head, Stump-

Type, Titanium Alloy.

NAS2306 thru NAS2312 - Bolt-Lock, Tension, 100° Head (MS24694),

Stump-Type, Titanium Alloy.

NAS2315 thru NAS2322 - Bolt-Lock, Tension, 100° Head (MS20426),

Stump-Type, Titanium Alloy.

NAS2325 thru NAS2332 - Bolt-Lock, Tension, 100° Crown Head, Stump-

Type, Titanium Alloy.

NAS2406 thru NAS2412 - Bolt-Lock, Shear, Protruding Head, Standard

and Oversize, Pull-Type, Titanium Alloy.

NAS2506 thru NAS2512 - Bolt-Lock, Shear 100° Head, Standard and

Oversize, Pull-Type, Titanium Alloy..

NAS2605 thru NAS2612 - Bolt-Lock, Shear, .Protruding Head, Stump-Type,

Titanium Alloy.

NAS2705 thru NAS2712 - Bolt-Lock, Shear, 100° Head, Stump-Type,

Titanium Alloy.

NAS4445 - Nut, Crimp, for Crimplock Fastener System.

NAS4450 - Pin, Crimp, Protruding Shear Head.

11
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. (AIA)

NATIONAL AEROSPACE STANDARDS - Continued

NAS4452 Pin, Crimp, 100° Flush Shear Head.

NAS4458 Pin, Crimp, Protruding Tension Head.

NAS4466 - Pin, Crimp, 100° Crown Shear/Tension Head.

NAS6915 thru NAS6922 - Pin, Swage Locking, Aluminum Alloy, 100° Head
(MS20426), Tension, Stump-Type.

NAS6925 thru NAS6932 - Pin, Swage Locking, Steel, 100° tiead (MS20426),
Tension, Stump-Type.

NAS6935 thru NAS6942 - Pin, Swage Locking, Steel, 100° Crown Head,
Tension, Pull-Type.

NAS6946 thru NAS6952 - Pin, Swage Locking, A-286 CRES, 100° Head
(MS24694), Tension, Pull-Type.

NAS6955 thru NAS6962 - Pin, Swage Locking, A-286 CRES, 100° Head
(MS20426), Tension, Pull-Type.

NAS6965 thru NAS6972 - Pin, Swage Locking, A-286 CRES, Protruding

l-lead,
Tension, Pull-Type. .

NAS6974 thru NA56982 - Pin, Swage Locking, A-286 CRES, 100° Shear
Head, Stump-Type.

NAS6984 thru NAS6992 - Pin, Swage Locking, A-286 CRES, Protruding

Head, Shear, Stump-Type.

NAS7004 thru NAS7012 - Pin, Swage Locking, A-286 CRES, 100° Shear/
Tension Head, Pull-Type.

NAS7014 thru NAS7022 - Pin, Swage Locking, A-286 CRES, Protruding

Head, Shear/Tension, Pull-Type.

NAS7024 thru NAS7032 - Pin, Swage Locking, 108 KSI Steel, 100°
Shear/Tension Head, Pull-Type.

NAS7034 thru NAS7042 - Pin, Swage Locking, 108 KSI Steel, Protruding
Head, Shear/Tension, Pull-Type.

(Applications for copies should be addressed to the Aerospace Inds.

Assoc. ofherica, Inc., 1725 DeSales St., NJJ~9 Washington, DC 20036.)

-
 Downloaded from http://www.everyspec.com

-. MIL-STD-1759
10 JULY 1979

SOCIETY OF AUTOMOTIVE ENGINEERS (SAE)

AERONAUTICAL STANDARD

AS125101 thru AS125250 - Rivet-lOOO Countersunk Head, Mild Steel.

(Application for copies should be addressed to the Soc ety of Auto-

motive Engineers, Inc., 400 Commonwealth Drive, Warrenda e, PA 15096.)

3. DEFINITIONS

3.1 Adopted Industry Standards. Any Industry Specification or

Standard which is listed in the Department of Defense Index of Specifi-
t
cations and Standards (DODISS). ‘

3.2 Commodity Type Document. A document which lists preferred parts

within a Federal Supply Classification class or Item Name. This do~ment
is to be used for selecting preferred parts for a new design when-the
document is invoked as a contractual requirement in conjunction with a
parts control requirement.

3.3 End Use Type Document. A document that lists preferred documents
and establishes parts requirements which are contractually binding for
the design and construction/manufacture of a weapon system or an
established equipment category such as MIL-STD=1515.

3.4 Military Parts Control Advisory Group (MPCAG). A Department of

Defense organization wh~ch provides advice to the Military Departments
and military contractors on the selection of parts in assigned commodity
classes, and collects data on nonstandard parts for developing or
updating military specifications and standards.

3.5 Definitions of approved item names used in this standard are as

follows:

a. Cap , Rivet. “A closure designed to fit over the end of a

split or tubular rivet shank and into which the shank end is crimped in
assembly, It provides greater strength and gives the appearance of a
solid rivet at the clinched end. The closure may have a knurled shank
and a head with its bottom recessed to fit over a hollow rivet head. It
is designed to be pressed or driven .through the head of a hollow rivet
when a closed assembly is required.

b. Collar, Grooved, Pin-Rivet. A sleeve of soft metal for

swaging into the locking groove(s) of a PIN-RIVET, GROOVED or a PIN-RIVET,
DOWEL thus forming a head.

13
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

Collar, Pin-Rivet, Threaded, An internally threaded sleeve,

designedc~o mate with a PIN-RIVET, THREADED. It may include an external
wrenching facility which breaks off at a predetermined torque.

d. Pin-Rivet, Grooved. A metallic item, headed at one end with

a cylindrically shaped shank having a circumferential groove near the
opposite end, or a series of grooves along its length, The grooves are
used to engage a collar or sleeve which is installed by means of a rivet
gun or riveting machine. The grooved shank may extend beyond the collar
or sleeve, performing the same holding action as the clinched portion of
a conventional rivet.

Pin-Rivet, Threaded. A metallic item, cylindrically shaped,

headed a~”one end and threaded at the other end. The threads are used
to engage a threaded collar or sleeve. The bottom of the shank may have
a hexagon socket which accommodates an installation tool. The shank may
extend beyond the collar or sleeve performing the same holding action
as the clinched portion of a conventional rivet.

f. Rivet, Blind. A headed fastening device with the shank

designed to be expanded by means of a separate or integral stem or
mandrel, or by means of an explosive charge in the shank detonated by
heat applied to the head. It is designed to be installed and expanded
from one side only.
.-
99 Rivet, Solid. A headed fastening device having a smooth
solid shank designed to have the shank end clinched after insertion.

h. Rivet, Split. A headed fastening device having a smooth

shank which is split, slotted or forked and designed to be spread or
crimped back after insertion.

i. Rivet, Tubular. A headed fastening device having smooth

shank which is hollow or having a cavity at its end and designed to have
the shank end clinched after insertion.

4. GENERAL STATEMENTS

4.1 Selection procedure.

4.1.1 Document selection. The applicable section sha77 be selected

after reviewing the table of contents.

4.1.2 Part number selection (Preliminary). A preliminary selection

of the applicable part number shall be made after reviewing the nOminal
parameters (sizes, materials, shear and tensile strength) listed in the
sections.

14
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

4.1.3 ~art number selection (final). A final selection of the

applicable part number shall be made after reviewing the detailed
requirements specified in the referenced rtvet and rivet type fastener
documents for suitability in the particular military equipment being
designed (considering the application and environmental conditions).

,5. DETAILED REQUIREMENTS

5.1 The detailed requirements for preferred rivets and rivet type
fasteners are contained in the applicable rivet and rivet type fastener
document and associated procurement specification. If there is disagree-
ment between the nominal parameters listed in this standard and the
parameters specified in the applicable rivet and rivet type fastener
document or associated procurement specification, the parameters speci-
fied in the applicable rivet and rivet type fastener document or associ-
ated procurement specification shall prevail.

6. NOTES

6.1 Dimensions. Dimensions shown in the sections contained herein

are in inches.

\.

15
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979
Preparing activity:
Custodians:
Air Force - 11
Army - AR
Navy -
Agent:
Air Force - 11 DLA- IS
Review activities:
(Project 5320-0314)
Army - EA, ER, MI -
Navy - St-1
Air Force - 99
DLA - IS
NS

User”activities:
Amy - GL, ME
Navy - OS, YD

16
 Downloaded from http://www.everyspec.com
.
.
.

MIL-STD-1759
10JULY 1979

SECTION101

CAPS,RIVET
APPLICABLEDOCUMENT: MS51924

TYPE I TYPE 11
(FOR USE WITH SPLIT RIVETS) (FOR USE WITH TUBULAR RIVETS)

Shear strength
---- Material Protective finish
(psi) min

Carbon steel
C1OO6 - Cadmiurn 32,000
thru plate
C1023
Brass
composition None or
oxide or 35,000
260 or 270
quarter hard black finish

TABLE 1. Cap configuration dash numbers.

MS51924 Dash no.

Rivet A c
Type size Rivet shank Outside diameters Steel Brass Brass
diameter (coated)

I ●094 .092 .297 S1-6 B1-6 K1-6

I .125 .125 .328 S1-8 B1-8 K1-8
I ,141 .152 .375 S1-9 B1-9 K1-9
I .188 .190 .375 SI-12 B1-12 K1-12
II .125 .123 .266 S2-8 02-8 K2-8
II ,141 .146 .344 S2-9 B2-9 K2”9
11 .188 .188 .438 S2-12 B2-12 K2-12
—
101.1

A
Downloaded from http://www.everyspec.com

,rh
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION
202

COLLAR [HIGHSTRENGTH]
HIGH-SHEARRIVET
APPLICABLEDOCUMENT: NAS528

I’-’l
----
r

Material Protective finish

ID

1
H -

----

Shear strength
3

(psi) min

Aluminum Anodize Not specified

alloy ~
2024-T4
b

TABLE I. NAS 528 Dash numbers.

Isizel ‘D T .190 I .167

Dash
no.

I ● 125 I .128

%t!E
●124
.156 .160
,156
.188 01930 .284 .210
.1895 .274 .200
.250 .2530 .250
.2495 * .240
.312 .3160 .461 ,291
.3120 .451 ,281
●375 .3785 550
● .333 -A12
i--
.500
.500 m
‘ ,625 .630 .912 I .498

I .625 .902 I .488

l(’) 20?. 1
Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

-. MIL-STD-1759
10 JULY 1979

SECTION201

COLLAR
HI-SHEARRIVET,1200°F
APPLICABLEDOCUMENT: NAS1585

.
L

rl----
T
Y-----
f3
Shear strength
Material Protective finish
(psi) min

Inconel per
AMS 5665
Not specified
I Not specified

TABLE 1. NAS1585”Dash numbers.

lsizellD1°DILID::~l
I .125 I .1280 I .181 I ,167 I -4 I
.1245 .171 ,157
.156 .1600 .225 .188 -5
.1565 .215 .178
.188 .1930 .270 .225 -6
.1895 .260 .215
●250 .2530 355
● .270 -8
.2495 .345 .260
.312 .3160 .437 .316 -lo
. .3120 .427 .306
.375 .3790 .523 .365 -12
.3745 .513 ●355

201.1
Downloaded from http://www.everyspec.com

-
 Downloaded from http://www.everyspec.com

.
.

----

MIL-STD-1759
10 JULY 1979

SECTION203

COLLAR,SWAGE LOCKING
FOR PULL-TYPEAND STUMP-TYPELOCKBOLTS
APPLICABLEDOCUMENTS: NAS108O

Material Protective finish Code

IIII tl~,,
,
2024
ll&: ,!~tl,Ipl!
Aluminum T4 Anodize
alloy 2219 IIAGII,lA~,l HAT!,
T6
6061 11~11
None
T7
Cl006
CIO08 lt~ll,
11~11
Carbon C1213 Cadmium plate
steel C1215
61113
CRES A-286 Passivate “UG”, “UK”
Nickel copper ll~&l, ,,~~tl

alloy None
(Monel)

203.1
 Downloaded from http://www.everyspec.com

. .

--

MIL-STD-1759
10 JULY 1979

.
FIGURE 1. Shear type collars - symmetrically double ended.

TABLE I. Collar configuration dash numbers.

F

Dimensions - shear type - figure 1

~ Lenqths NAS108O
A D F H Dish number
Al Mone 1
4

Mi- MaY Mi n. I ..
Max
... I M;
.ax Min Aluminum Steel
Max Min n ,,“n I .... 1 1

f MG04
9 I ~f)A I
,ILL
199 9nl I ?07 nl~ I 1f?~ .171 AG04 UG04
.126 .Ic% .Lvl .12/ ● WIW .,””

>
,168 .157 C04 E04 -
.202 .016 .210 I 1a7 1 knd (- l-l
.134 129 .127 .206 l#f
● ,,”- ! L

.130 :126 .121 .204 .200 I

I I
I ----
I IIK04
-----
, .,-A-
I MK04 1
....-
1 ,.-nr 1
.168 ,165 .260 .256 .016 .208 .19- AG05 Ubua I mbu3
.173
.173 .168 .165 .260 .256 .016 .234 .21; K05 I
I - MKnF
I ufivd I IVV.WW
Iivnk I
161 ,157 .152 .252 .248 I
.016 .240 .225 AG06 I - I - I
:192 ,187 .183 ,303 .299
Cn& 1-
I 1- 41
I I 1
.208 .203 .200 .310 .306 .016 .253 .238 w “ -
.302 .298 UK06 MK06
194 190
:253, :248 :2:: .396 .392 .016 .298 ,283 AG08 - -
-
m-% “36 .016 K08
I .VL
ner -C9 Aln
.</1 .;00 I .LOJ 1 .+IU
9nn UK08 MK08
.254 .250 .244 I .aYY 1 .234
.315 .310 .307 ,497 *;;2 .031 .317 .302 AGln I - I - I
Gld I I
216 ~ln
mlw I . 1 . I
.336 330 .327 .511 .506 .031 .334 .a17

3
●

.313 I .306 .500 .494 I

1 I
1 . 1 UK1O 1 MK1O I
:3;: .373 .370 .601 ,596 .031 .396 .381 1 AG12 I - ! - 1
G12 I - I -
*399 .393 .390 .612 .607 .031 .370 .355 K12 ! - -
.380 .375 .368 .600 .594 UK12 MK12

203s2
e.-
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TOP VIEW OF FIGURES 2, 3 &?4

FIGURE 2. Shear type collars

NAS108OCO6 and NASI080C08.

FIGURE 3. Shear type collars FIGURE 4. Shear type collars

NAS108OCIO and NASI080C12. NAS108OEO6 thru NAS108OE12.

.
TABLE 11. Collar configuration dash numbers.

Y 1 I
Dimensions - shear type - figures 2, 3 ii4
Diameters Lengths NAS108O
t) Dash
F H J
A Al B c D\ < number
Max Min Min Max Min Max Min Min Max Max Mln Max Min
\
r 1 1 I 1

I I I l-l I f-Q~
.191 ---’ ---’ – ‘ – ‘ – ‘– ‘
-C)n duo..~ I .Ulo I .6U2 I
I
. ID.J I
1
- I1 I --l
---
F(76
.1935 .1885 .185 I - - I‘ “n” 1 .LOO L _
.(CY* I
(XIX
1
I
J
!
1 .
99
C.bv I
---
.252 ,248 .243 : : ;9 ~ :8*’ ‘; .016 )-;;:, --‘ii
72A I ~ :
i II -. 1
H. t
,
.356 .349 ,497 .492 506 L.H .
.309 ● 305 .301 “- - ,495 ,489 :499 ‘n” : ‘;; I 1 1

.416 .408 , ,604 .298 I .092 I .084 I iii

n91 **-
.377 .373 .367 .596 .589 “!UJI r.323 I .3031 - I - tld
I I l-l–l I I .cnn
Wuu I I I

203.3
 Downloaded from http://www.everyspec.com
.

.:. .

MIL-STD-1759
10JULY 1979

.
FLH7

FIGURE 5. Tension type collars

for 4-lockinq -groove type lockbolts.
.

TABLE 111. Collar configuration dash numbers.

Dimensions - tension type - figure 5

Diameters Lengths
NAS108O
A c D1 F H Dash
numbers.
Max Min Min Mi n Min Max Max Min

-05
~ AT05
.169 .164 .163 .266 .256 .264 .016 .200 .170

-+-i
.193 -06 I
.310 304 .311 .016 .263 .233 AT06

4
●

.199 w D06

a
.193 .180 .031 .257 .227 R06
.254 .-246 -08
.409 .402 .412 .016 .335 .305 AT08 “
.265 w D08
.265 .259 .241 .046 R08
-10
.312 ● 304 .301 .507 .499 .512 .031 .380 .350 AT1O

+-i
.378 .371 .367 .609 .600 .612 .031 ● 509 .479
X m -+-i

203.4
 Downloaded from http://www.everyspec.com

&

---

MIL-STD-1759
10JULY 1979

FIGURE 6. Tension type collars

for 5-lockinq-q roove type lockbolts.

TABLE IV. Collar configuration dash numbers.

Dimensions - Tension type - Figure 6

Diameters Lengths
I NAS1080

A Al D1 F H Dash
number
Max Min Min Min Max Max Min

Plo
.316 .310 .301 .510 .031 .420 .390 AP1O
R1O
P12
.380 .372 .367 .618 ,031 ● 540 .510 API 2
RI 2
 Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

-
MIL-STD-1759
10JULY 1979

SECTION204

COLLAR,SWAGE-LOCKING;
REGULARHEIGHT,FLANGED
AND LOW PROFILE,
ALUMINUM ALLOY,CORROSIONRESISTANT
STEEL,CARBONSTEELAND ALLOYSTEEL
APPLICABLEDOCUMENT: MIL-P=23469/l

Tensile strength Class

Material Protective finish (psi) min

Aluminum alloy Not specified 19,200 1

6061

CRES #10
AISI 305 or Cadmium plate 52,600 2
AISI 430F

Carbon steel
C1OO6 thru Zinc coat 59,700 3
CIO08

Alloy steel Zinc coat Not specified 4

A242
●

----
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 IJULY1979

TYPE I - REGULAR HEIGHT COLLARS FOR USE

WITH PINS HAVING SIX LOCKING GROOVES
.

--- , --- -(
I I
I I

I I
I

CLASS 1 AND 3 MATERIAL CLASS 2 MATERIAL

TABLE I. Collar configuration dash numbers.

M23469/1 Dash no.

A B c Class 1 Class 2 Class 3
1
Size Dia Dia Carbon
Al
I Cres
Isteel I
w

309 .195 .237

-10106 -
●

.306 .197 .247

.305 ,1875. .240
.188 -20106 -
●301 .1895 .250 -
,309 .1895 .222
.306 .1925 .232 I -30106

.406 .261 .306 -10108

.403 .263 .318
.393 .250 .295
.250 -20108 -
.389 .252 .305
.406 .261 .294
-30108 .
.403 .263 ,304
.505 .306 .354 -10110
.501 ,-
.308 .364

.312
.486
.482
.492
.308
.310
.306
.360
●370
354
-20110
I -

.487 .310
●

.364 I
1
1
I
i
-30110

.608 3735 .431

I
●

.600 .3765 .441 -10112 I

●375 .588 .377 .390

.584 .382 .400
I -20112
I
.598 .377 .433
-30112
.591 .382 .443

204.2 .
 Downloaded from http://www.everyspec.com

.
.

.:.

-----
MIL-STD-1759
10JULY 1979

TYPE I - REGULAR HEIGHT COLLARS FOR USE

WITH PINS HAVING MULTIPLE LOCKING GROOVES

CLASS 1, 2 & 3 MATERIAL

TABLE I. Collar configuration dash numbers.

M23469/1 Dash no.
A B c Class 1 Class 2 Class 3
Size Dia - Dia C;;::;
Al Cres

w
----
,795
.785
.520
.527
.61;
l-l
t
,785 .527 . -20116
.500 ,775 }
.534 .635
.520 .615
,795
.785 .527 I
I
67G
.“”- I
1
I
!
I1 -30116 I
1 i

.979
.974
.651
“p-
.031
1 .798
970 I ,110
-10120 - I I
.979 .651 .798 -20120
.625 n7A
[
I .7/+ I ,657 .778
.-. ,. -A
.651 ●/u
.979
.974 II K:7
.“-r II .Rm
---- I
I
I1 I
1

i
-30120
I
1
.781 .935
1.176
,1.170 .707
,iol
I OKR
.Zdd
I -10124 I - I I
r

1.176 ,781 .935 . -20124 -

●750 7Q7
.955
,1.170 1 .10!
~ 1.176 .780 .935 - -W1174
-w.-.
i~i70 .787 I (I6G I I I I

1.356
1 349
●
.923
.930
1.088
10IOP
J
I -10128 I - I
I
I
- I
J

n7c 1.371 .923 3

I 1.08f -20128 -
.Utd
I 1 lf)~
11.364 I .930 i I*1W3 1 I
I I -30128
I
I .

1.240
&uu
r -10132 I I I
1 000
● . A,- -20132 .-
,1.556 1.042 ‘)
I.(XX
? -----
1.564 1.039 1.245 I I
 Downloaded from http://www.everyspec.com

. .

MIL-STD-1759
10 JULY 1979

TYPE 11 - FLANGED COLLARS FOR USE WITH PINS

HAVING SIX LOCKING GROOVES

CLASS 1 AND 3 MATERIAL CLASS 2 MATERIAL

.
TABLE 1. Collar configuration dash numbers.

M23469/1 Dash no.

A B c class 1 Class 2 Class 3
Size Dia Dia Carbon
Al Cres steel

.309 .1895 .260

-10206 -
.306 .1925 .270
.188 .305 .1875 .287 . -20206 -
.301 .1895 .297
.311 .1895 .260 - -30206
.306 .1925 .270
.406 .261 .359 -10208 -
.403 .263 .369
.250 .393 .250 .357 I - I -20208 I
.389 .252 .367
.406 .261 .359 - -30208
.403 .263 .369 .
.505 .308 ●404 -10210 -
.501 .310 .414
.312 .485 .308 .438 - -20210 - .
,483 .310 .448
.505 .308 ,404 - -30210
.501 .310 .414
.608 .3735 .512 -10212 -
.600 .3765 .522
.375 e588 .377 .484 -20212 -
.S84 .382 .494 -
.608
.600
.3735
.3765
.512
.522 I -
I -30212
-

204.4

- f\
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759
10JULY 1979

TYPE II - FLANGED COLLARS FOR -—-

USE WITH PINS
—..--
HAVING MULTIPLE LOCKING GROOVES

CLASS 1, 2, 3 & 4 MATERIAL

FOR .875 & 1.000 SIZE

TABLE I. Collar configuration dash numbers.

M23469/1 Dash no.
A B c Class 1 class 2 Cldss 3 class 4
Size Old Oia Carbon Alloy
Al Cres steel stee1

.805 .520 .720 -?0216 -

.795 .527 .740
.805 .s20 I .720 j - -20216 ~ - -
.795 .527 .740 I i
.500
,805 .520 .720 - -30216 -
.795 .527 .740
.805 .520 .720 -40216
.795 .527 .740 -
.993 .651 .863 -10220 -
.983 .657 .883
.993 .651 .863 - -20220 -
.983 .6S7 .883
.625
.993 .651 .935 - -. -30220 -
.983 .657 .955
.993 .65i .935 - -40220
.983 .657 .955
1.190 .781 1.122 - ~0224 - - -
1.180 ,787 1,142
1,190 .781- 1.122 - -20224 -
.750 1.180 .787 1.142
1.190 ,781 1.122 - -30224 -
1.180 .787 1.142
1.190 .781 1.122 - -40224
1,180 .707 1.142
1.356 .923 1.305 -10228 -
1.349 .930 1.325
1.371 .923 1.305 -- -20228
. - -
1.364 .930 1.325
.875
1.371 .923 1.305 - -30228 -
1.364 .930 1.325
1.371 .923 1.305 - -40228
1.364 .930 1.325
1.551 1.032 1.490 -10232 - -
1.543 1.040 1,510
1.564 1.034 1.490 - -20232 -
1.000 1.556 1.042 1.510
1.564 I.034 1,490 -
1.556 1,042 1.510 -30232 -
1,564 1.034 1.490 - -40232
1.556 1.042 1.510 4
*

204.5
—
Downloaded from http://www.everyspec.com
. .

MIL-STD-1759
10JULY 1979

TYPE III - LOW PROFILE COLLARS FOR USE WITH

PINS HAVING SIX LOCKING GROOVES
.

r ‘I
I

1-
I
-. --
“- T
B
f

A
I
I
----.-
‘“ :1

‘1 l-c-l
CLASS 1 & 3 MATERIAL CLASS 2 MATERIAL
.
TABLE I. Collar configuration dash numbers.

M23469/1 Dash no.

A B c Class 1 Class 2 Class 3
Size Dia Dia Carbon
Al Cres steel

309 .1895 .142

●

.306 ..1925 .152

-10306
I I
.188 309 -.1895 ~ .142
●
-20306 -
.306 .1925 .152
,309 .1895 .142
.306 .1925 .152 I -30306

.406
.403
.261
,263
,182
.192
-10308
I
.250 .182
.250 .393
.389 .252 .192 I -20308
I -

.406 .261 .182

.403 .263 I .192 I -30308

.505 .306 I .235

-%-w-
-10310 I
.501
.312 .489
.483 1 -20310
I - .

“3031O
.492
.487
+-t+%-
.310 I .245 1 I
,608 .3735 I .283 -10312 -.
.600 .3765 I .293 I
●375 .588 .377 I .283
I -20312
I
.584
.598
.591
+%-k%+.382 I .293
-30312
-

204.6

Al\ .. -
 Downloaded from http://www.everyspec.com

....

MIL-STD-1759
10 JULY 1979

TYPE 111 - LOW PROFILE COLLARS FOR USE WITH

PINS HAVING MULTIPLE LOCKING GROOVES

I-CA
CLASS 1, 2 3 MATERIAL

TABLE 1. Collar configuration dash numbers.

M23 59/1 Dash I

A B c Class 1 Class 2
Dia Carbon
Size Max Al Cres steel
I t

I
I .795 I .520 .475
-10316
.495
M-H-
‘L.

.475 -20316
.500
.495

H!-i-%- .475
.495
.603
-30316

.974 .657 ,623 -10320

.979 .651 .603 -20320
.625
.974 .657 .623
.979 .651 ,675 -30320
.974 .657 .695
1.176 .781 .720 -10324
.787

m
I 1.170 I .740
--%- -20324

“750 1.170 .787

.740
.720
.740
-30324

1.356 .923 .838 -10328

1.349 .930 .858

--l
1.371 .923 .838 -20328
.875
1.364 .930 .858
1.371 I .923 .838 -30328
1.364 .930 .858
‘1*551 1.032 .955 -10332 T-i
‘*’oo
I 1.543

ITETE
1 1.040 .975
.955
.975
-20332 =--l
1.564 1.034 .955 -30332
1.556 1.042 .975
.
Downloaded from http://www.everyspec.com

-:..

MIL-STD-1759
10JULY 1979
TYPE IV - REGULAR HEIGHT DOUBLE END COLLARS FOR USE
WITH PINS HAVING MULTIPLE LOCKING GROOVES

I
&-c 4
CLASS 1, 2 & 4 MATERIAL .
TABLE I. Collar configuration dash numbers.

M23 69/1 Dash ).

.
c Class 1 Class 2 class 3
Size A B Carbon
Dia Dia Al Cres steel

.775 .520 .615

-10416
.765 .527 .635
500 .785 .520 .615
●
-20416
.635
.615 .
+-t+- -40476
.775 I .527 .635
.956 .652 .778
-10420
.950 .657 .798
.625 .966 .652 .778
-20420
.961 .657 .798
.966 .652 .850 -40420
.961 .657 .870
.935
-10424
.955
.750 1.159 .780 .935
-20424
1.153 .786 .955
1.159 .780 .935
-40424
1.153 .786 .955
1.341 .923 1.093
-10428
1.338 .927 1.103
.875 1.351 ,923 10093
-20428
1.348 .927 1.103
1.351 .923 1.093 -40428
1.348 .927 1.103
1.533 1.034 1.245 -10432
1.530 1.037 1.255
1.000 1.543 1.034 1.245
-20432
1.540 1.037 1.255
1.245 -40432
1.255
e
7fM Q
 Downloaded from http://www.everyspec.com

---

MIL-STD-1759
IOJULY 1979

TYPE V - LOW PROFILE DOUB LE END COLLARS FOR USE

WITH P.INSHAVING MULTI PLE LOCKING GROOVES

I
*C-4

CLASS 1, 2 & 4 MATERIAL

TABLE I. Collar configuration dash numbers.

M2: 69/1 Dash 2

I I Class 2 -
I I Class 1
Size A IB I Cres
Alloy
Dia Dia Al steel
I

,775 ‘w520 .480 -10516

.765 .527 .490
I .785 .520 .480 -20516
,500
.775 .527 .490
.785 .520 .480 -40516
.775 .527 .490
.608

.625 +!%-++%
.961 .657
.618
.608
.618
.680
-10520

-20520

.966 .652 -40520

.961 .657 .690
1.146 “ .780 .725 -10524
1.140 .786 .735
10159 .780 .725 -20524
.750
10153 .786 .735
1.159 .780 .725 -40524
1.153 .786 “.735
1.341 .923 .843 -10528
1.338 .927 .853
1.351 .923 .843 -20528
,875
1.348 .927 .853
1 351
● .923 .843 -40528
1.348 .927 .853
1.533 ‘ 1.034 .960
-10532
1 530
● 1.037 .970
1.000 10543 “1.034 ,960 -20532
1..540 1.037 .970
10543 1 .034— .960 -40532
.970
1 540
●
A 1.037
 Downloaded from http://www.everyspec.com

-.
 ●
Downloaded from http://www.everyspec.com

L-

MIL-STD-1759
10 JULY 1979

SECTION301

FASTENERSYSTEM
NUT,CRIMP,FORCIIIMPLOCK
APPLICABLE
DOCUMENT:NAS4445

I >4 GROOVES
/ ~GAI EQUALLY

(EXCESS SEALANT
SPACED

ESCAPE GROOVES)

Tensile strength
Material Protective finish (psi) min
I
1

Alloy steel Cadmium plate 93,700

AISI 4130
or 8740 1

Cres Passivate or 93,700

A-286 cadmium plate

Aluminum alloy Anodize 70,500

2024-H13 I

TABLE I. NAS4445 Dash numbers.

1
c
Dia
Cres and D G H Dash
A
Al Dia no.
Thread alloy steel

.1640-32
UNJC-3B
.1900-32
d;;

.193
.167
.171
.208
.274
.268
.320 .160
.135
.145
.247
.262
.273
7 -05
I
-06
UNJF-3B .197 .213 .312 .170 .288
.2500-28 .254 .269 .417 .210 .335 -08
UNJF-3B .258 .274 ,409 .220 .350 +

.3125-24 .318 .333 .523 .261 .398

UNJF-3B .322 .338 .516 .271 .413
.458
Q-J
.3750-24 .381 .396 .627 .313 -12
UNJF-3B ;385 .401 .620 .323 .473

NOTE: This part intended for use with NAS4450,

NAS44$2, NAS4458 and NAS4466 pins.
301.1
 Downloaded from http://www.everyspec.com
.

-1

.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION302

NUT,EXTENDEDWASHER, HEXAGON-
SELF-LOCKING,
LOW HEIGHT,
C’BORE
APPLICABLEDOCUMENT: NAS1287

I T THREAD

ORE
A

---

Shear strength
Material Protective finish
(psi) min

Alloy steel Nickel-zinc alloy Not specified

AMS 6304 plating and hydro-
gen embrittlement

Heat resist- Silver plate Not specified

ant nickel ●

base alloy
perAMS 5756;
M252

TABLE I. NAS1287 Dash numbers.

E
c D Dash no.
T Chore H
Min Dia dia Max
Thread 14000F 8000F
max min
, h
f
.1640-32 UNJC-3B .284 ! .168 ● 220 I C08 I 08

.1900-32 UNJF-3B .322 I .194 .240 I C3 I 3

.2500-28 UNJF-3B .090 .416 I .254 ● 280 I C4 14

.3125-24 UNJF-3B .512 .1 0317 .320 C5 I 5

I I
.3750-24 UNJF-3B I ,605 I .379 .360 I C6 16
 .
Downloaded from http://www.everyspec.com

--

n
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION303
NUT,HEXAND WASHER,SELFALIGNING,
SELF-LOCKING
-SHEARPIN
APPLICABLEIIOCUMENT:NAS1288
.

l-H%- r’1

-+’R SPHER
RAD WASHER
-NUT
Shear strength
Material Protective finish
(psi) min
“--

Alloy steel Nickel-zinc alloy Not specified

AMS 6304 plate and hydrogen
embrittlement

Heat resistant Silver plate Not specified

nickel base
alloy per
~MS 5756
M252
TABLE I. NAS1288 Dash numbers.

T H 1/ Cl/
D
Dja
R s u x
Ref
y
Dia
===1”
Thread Ma~ Miii ma x
I
Dia
max 14000F 1
8000F
I C08 08
.1640-32 UNJC-3B ● 220 ,090 I .327 ● 200 .0501 :215 j.020 ● 300 C08W 08N
I
f

.1900-32-UNJF-3B .240 .090

I .365 .250 .060
II
.240 .025 ● 330 C3
C3W +
3
3W
C4 4
I
--l
.2500-28 UNJF-3B .280 .090 .457 ,300 .080 .310 .040 .420
C4W 4W
I

.3125-24 UNJF-3B .320 ,090 ,549 .350 .100

.375
II .055 .520
C5
C5W
5
5W

.3750-24 UNJF-3B .360 ● 090 .640 ● 400 .120 ,445 I .070 .620
C6
C6W -1 6
6W

—1/ Dimension “C” total counterbore and dimension

“H” exist at assembly of nut and washer.
. .
Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

->.
MIL-STD-1759
IOJULY 1979

SECTION304

PIN-RIVET
COLLAR,THREADED,
TORI)
UE-OFF,
SELF-LOCKING
.APPLICABLEDOCUMENT: MIL=P-23470/18,/20./22

ELLIPTICAL LOCKING ACTION

L~~’
L:ZI

TABLE I Part numbers.

Nomina1
size
A
Dia z
Thickness
I L
Thickness
Width
across
flats
Max Min b= Mln (hex)

.188 0370 .350 .240 .460 .420 .375 -1

.250 ,500 .480 ,315 .560 .520 ●500 -2
.312 .560 .540 .360 .640 .600 .562 -3
.375 .670 .650 .405 .720 .680 .688 -4
.438 .750 .730 .470 .815 775
● ●750 -5
.500 .870 .850 .520 .890 .850 .875 -6
.625 1.000 .980 ●570 .960 ,920 1.000 -7
.750 1.110 1.090 *700 1.230 1.190 1.125
.875 1.445 1.414 .990 1.500 1.470 1.250 ::
1.000 1.732 1.700 1.125 1.702 1.672 1.500 -lo

Footnotes
I
Part numbers
I Materials Protective finish
-

M23470/22
+ dash no.
Aluminum
alloy
6061 -T6
Anodic coat 3B(UNF-3B)
I
M23470/18 Carbon steel
HDBK
+ dash no. ASTM A675
H28
or A576
Zinc plate 2B(UNF-2B)
M23470/20 CRES 303
+ dash no. or 303SE
of ASTM
A 582
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

-----
MIL-STD-1753
10JULY 1979

SECTION305

PIN-RIVET
COLLAR,THREADED,TORQUE-OFF,
SELF-LOCKING,
[DOUBLEHEX]
APPLICABLEDOCUMENT: MIL-P-23470/190/21,/23

ELLIPTICAL LOCKING ACTIO

I

I
.P -w -!

TABLE I. Part numbers.

w
A L
Width
Nominal Dia z Thickness J/s 2/
across or ~-
size Thickness
flats
Max Min Max Min (hex)

.188 .370 .350 .240 .460 .420 .375 -1

.250 .500 .480 .315 .540 .520 ● 500 -2
.312 .560 .540 .360 .640 .600 ,562 -3
.375 ,670 .650 .405 .720 .680 ● 688 -4
.438 .750 .730 .470 .815 .775 .750
,500 .870 ,850 .520 .890 .850 ,875 ::
.625 1,000 .980 .570 .960 .920 1.000 -7
.750 1.110 1.090 .700 1.230 16190 1,125 -8
.875 1.445 1.414 .990 1.500 1.470 1,250 -9
1 000
● 1.732 1.700 I 1.125 1.702 1.672 1.500 -lo I

r I i I

Thre, is
Footnotes Part Numbers Materials Protective finish Class Ref
~/ M23470/23 Aluminum Anodic coat SB(UNF-3B)
+ dash no. alloy
6061-T6

g/ M23470/19 Carbon steel

+ dash no. ASTM A675 HDBK
or A576 H28
Zinc plate 2B(UNC-2B)
~/ M23470/21 CRES 303
+ dash no. or 303SE
of ASTM
A582

r / ~ns 1
Downloaded from http://www.everyspec.com

. h
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION401

BOLT-LOCK,
SHEAR,100°HEAD,
PULL-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS 2506THRU 2512

-.. —..-
-------

70 =::
= ..-.x

Shear strength
Material Protective finish
(psi) min

Titanium None 95,000

alloy
6AL-4V
●

TABLE 1. Pin-rivet, qroove, configuration part numbers.

Al Basic
D B
Nom size Min dia Max part
number

.190 .263 .049 NAS2506

.250 .346 ,064 NAS2508
.312 .417 m070 NAS251O
.375 .496 .081 NAS2512

.,, 401.1
 . Downloaded from http://www.everyspec.com

MIL-STD-1759 .-
10 JULY 1979

al
QJ
U’1

c“
o

aJ
Ln

L
m
1-

..
w
t-
0
z

401.2
● ✎
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION402

SHEAR,100°HEAD,
BOLT-LOCK,
STUMP-TYPE,TITANIUMALLOY
.
APPLICABLEDOCUMENT: NAS2705THRU 2712

10

Shear strength
Material Protective finish
(psi) min

Titanium None 95,000

alloy
6AL-4V ~

TABLE I. Pin-rivet, qroove, configuration part numbers.

D Al ● Basic
Nom Mln B part
size dia Max number

,164 .220 ●040 NAS 2705

,190 .263 .049 NAS 2706
.250 .346 .063 NAS 2708
.312 ,417 .070 NAS271O
.375 .496 .081 NAS 2712
 Downloaded from http://www.everyspec.com

-,

MIL-STD-1759
10JULY 1979

TABLE II. NAS2705, 2706, 2708, 2710 and.2712 Dash numbers.

Grip range G L Grip

G dash
Min “ Max .156 Dia .19G Dia .250 Dia .312 Dla .375 Dia number
v
.062 ~1 .062 .062 .236 - - - “ “01
.125 .063 .125 .125 .298 .323 -02
.188 .126 ,188 ,188 .361 .386 .439 .458 .501 -03
.250 .189 .250 .250 .423 .448 .501 .520 .563 -04
.312 .251 .312 .312 .486 .511 .564 .583 .626 -05

.375 ,313 .375 .375 .548 .574 .626 .645 .688 -06
.438 .376 .438 .438 .611 .637 .689 .708 .751 -07
.500 .439 .500 .500 .673 .699 .751 .770 .813 -08
.562 .501 .562 .562 .736 .762 .814 .833 .876 -09
.625 .563 .625 .625 .798 .824 .876 .895 .938 -lo

● 688 .626 .688 .688 .861 .887 .939 .958 1.001 -11
● 750 .689 .750 .750 .923 ● 949 1.001 1.020 1.063 -12
.812 .751 ,812 .812 .986 1.012 1.064 1.083 1.126 -13
.875 .813 .875 .875 1.048 1.074 1.126 ::145 1.198 -14
.938 .876 .938 .938 1.111 1*137 1.189 1,208 1.251 -15

1.000 .939 1.000 1.000 1.173 1.199 1.251 1.270 1.313 -16
1.062 1.001 1.062 1.062 - 1.261 1.314 1.333 1.376 -17
1.125 1.063 1.125 1.125 - 1.323 1.376 1.395 1.438 -18
1.188 1.126 1,188 1.188 - 1.386 1.439 1.458 1.501 -19
1.250 1.189 1.250 1.250 - 1.448 1.501 1.520 1.563 ‘ -20

1.312 1.251 1.312 1.312 - 1.511 1.564 1.583 1.626 -21

1.375 1.313 1.375 1.375 - 1.574 1.626 1.645 1.688 -22
1.438 1.376 1.438 1.438 - 1.637 1.689 1.708 1.751 -23
1.500 1.439 1.500 1.500 - 1.699 1.751 1.770 1.813 -24
1.562 1.501 1.562 1.562 - 1.762 1.814 1.833 1.876 -25

1.625 1.563 1.625 1.625 - 1.824 1.876 1.895 1.938 -26

1 688
● 1.626 1.688 1.688 - 1.887 1.939 1.958 2.001 -27
1.750 1.689 1.750 1.750 - 1.949 2.001 2 020
● 2.063 -28
1.812 1.751 1,812 1.812 - 2.012 2.064 2.083 2.126 -29
1.875 1.813 1.875 1.875 -~ 2.074 2.126 2.145 2.188 -30

1.938 1.876 1.938 1.938 - 2.137 2.189 2.208 2.251 -31

?.000 1.939 2.000 2 000
● - 2.199 2.251 2.270 2.313 -32 .

lJ Minimum grip for -01 varies with material to be fastened together.

NOTE : For collar selection, see NAS108O. -

 Downloaded from http://www.everyspec.com

..
=,

-.

MIL-STD-1759
10 JULY 1979

SECTIOtIJ
403

BOLT-LOCK,
SHEAR,PROTRUDINGHEAD,
PULL-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2406THRU 2412

I--’l
=-----
----..-

-. .-. ..
I
I

l-- L+
1

Shear strength
Material Protective finish
(psi) min
I J

I
Titanium None “ 95,000
alloy
6AL-4V

TABLE I. Pin-rivet, groove, configuration part numbers.

Basic
D A. B
part
Nom Size Dia number

.302 .063
.190 NAS2406
,288 .056
.377 .081 NAS2408
.250 ,074
.363
.471 .100 NAS2410
.312 .455 .094
,565 ,120
.375 NAS2412
.549 ,113
 Downloaded from http://www.everyspec.com

-
MI L-STI)-1759
10’JULY 1979

w A
 Downloaded from http://www.everyspec.com

..

-.
MIL-STD-1759
10 JULY 1979

SECTION404

SHEAR,PROTRUDINGHEAD,
BOLT-LOCK,
STUMP-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2605THRU 2612

Shear strength
Material Protective finish (psi) min
I

Titanium None 95,000

alloy
6AL-4V

TABLE 1. Pin-rivet, qroove, confiquratiOn part numbers.

D A Basic
B
Nom Dia part
size number

.249 ,048
.164 NAS2605
.235 .036
-m?!- T
NAS2606
.190
.288 .044
7 -mr
.250 NAS2608
.363 ,058
.471 .079 NAS261O
.312 ,455 .067
T r
.375 NAS2612
,549 .077
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

TABLE 11. NAS2605, 2606, 2608, 2610 and 2612 Dash numbers.

Grip ‘ange G L Grip

G dash

——
Min Max 156 Oia .190
I I
Dia .250 Dia .312 Dia .375 Dia number

.062 ~/ .062 .062 .236 .261 -01

.125 .063 .125 .125 .298 .323 .;76 .395 .~38 -02
.188 .126 ●188 .188 ,361 ,386 .439 .458 .501 -03
.250 .189 ,250 .250 .423 .448 .501 .520 .563 -04
.312 .251 .312 .312 .486 .511 .564 .583 .626 -05

.375 .313 .375 .375 .548 .574 .626 ,645 .688 -06
.438 .376 .438 .438 .611 .637 .689 .708 .751 -07
.500 .439 ●500 ●500 .673 .699 .751 .770 .813 -08
.562 .501 .562 .562 .736 .762 .814 .833 .876 -09
.625 .563 .625 .625 .798 .824 .876 .895 .938 -lo

.688 .626 .688 ,688 .861 .887 .939 .958 1.001 -11
.750 .689 .750 .750 .923 .949 1.001 1.020 1.063 -12 ‘
.812 ,751 .812 .812 .986 1.012 1.064 1.083 1.126 -13
.875 .813 .875 .875 1.048 1.074 1.126 1.145 1.188 -14
.938 .876 .938 .938 1.111 1.137 1.189 1.208 1.251 -15

1.000 .939 1.000 1 000

● 1.173 1.199 1.251 1.270 1.313 -16
1.062 1.001 1.062 1.062 1.261 1.314 1.333 1.376 -17
1.125 1.063 1.125 1.125 1.323 1.376 1.395 1.438 -18
1.188 1.126 1.188 1.188 1.386 1.439 1.458 1.501 -19
1.250 1.189 1.250 1.250 1.448 1.501 1.520 1.563 -20

1.312 1.251 1.312 1.312 1.511 1.564 1.583 1.626 -21

1.375 1.313 1.375 1.375 1.574 1.626 1.645 1 688
● -22
1.438 1.376 1.438 1.438 “1.637 1.689 1.708 1.751 -23
1.500 1.439 1 500
● 1.500 1.699 1.751 1.770 1.813 -24
1.562 1.501 1.562 1.562 1.762 1.814 1.833 1.876 -25

1.625 1.563 1.625 1.625 1.824 1.876 1.895 1.938 -26

1.688 1,626 1.688 1 688
● 1.887 1.939 1.958 2.001 -27
1.750 1.689 1.750 1.750 1.949 2.001 2.020 2.063 -28
1.812 1.751 1.812 1.812 2.012 2.064 2.083 2.126 -29
1.875 1.813 1.875 1.875 2.074 2.126 2.145 2.188 -30

1.938 1.876 1.938 1.938 2.137 2.189 2.208 2.251 -31

2,000 1.939 2.000 2 000
● 2.199 2.251 2.270 2.313 -32

~/ Minimum grip for -01 varies with materials to be fastened together.

-
NOTE : For collar selection, see NAS108O.

404,2
e- 1A t-
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION405

BOLT-LOCK,
TENSION,
100°CROWN
HEAD,PULL-TYPE,
TITANIUMALLOY
APPLICABLEDOCUME~T: ?iAS2125
THRU 2132

o-~—,

r
r- D

t I I

Tensile strength
Material Protective finish (psi) min
I I
I
Titanium alloy None 106,000
6AL-4V
k

TABLE I. Pin-rivet, qroove, configuration part numbers.

D B Basic
‘1
Nom Min Ref U. part
size dia u number

.164 .229 .036 4 NAS2125

.190 .269 .045 4 NAS2126
.250 .361 .061 4 NAS2128
.312 ●440 .073 5 NAS2130
.375 .537 .086 5 NAS2132

1/ Number of locking grooves.

 Downloaded from http://www.everyspec.com

MIL-STD-1759
IOJULY 1979

-
‘Cu
WI

L
fu

0
w
L

1!?

~ 405.2
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

SECTIOH06

BOLT-LOCK,
TENSION,
100°CROWN HEAD,
STUMP-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2325THRU 2332

I AI
t

@
/
+
\/.-
‘,

.
*
Tensile strength
Ftaterial Protective finish} (psi) min
,
I !

1 1
Titanium alloy
6AL-4V I None 106,000

TABLE I. Pin-rivet, qroove, configuration part numbers.

D Al Basic
Nom Min B part
size dia Max number

.164 .229 .036 NAS2325

.190 .269 .045 NAS2326
.250 .361 .061 NAS2328
.312 .440 ●073 NAS2330
.375 ,537 .086 NAS2332

r% 406.1
 .
Downloaded from http://www.everyspec.com
.
.
.

MIL-STD-1759 --
10 JULY 1979

“TABLE II. NAS2325, 2326, 2328, 2330 and 2332 Dash n’umbers.

Grip range L
Grip
G dash
Min Max .164 Dia .190 Dia .250 Dia .312 Dia .375 Dia number

.125 .095 .156 .324 .373 .456 -02

.188 ,157 .219 .387 .435 .519 .;02 .;97 -03
.250 .220 .281 .449 .498 .581 .664 .760 -04
.312 .282 ●344 .512 .560 .644 .727 .822 -05
.375 .345 .406 ,574 .623 .706 .789 .885 -06

.438 .407 .469 .637 .685 .769 .852 .947 -07

,500 .470 .531 .699 .748 - .831 .914 1.010 -08
.562 .532 ,594 .762 .810 ,894 ,976 1.072 “09
.625 .595 .656 ,824 .873 .956 1.039 1.135 -10
.688 .657 .719 .887 .935 1.019 1.101 1.197 -11

●750 .720 .781 .949 .998 1.081 1.164 1.260 -12

.812 .782 .844 1.012 1.060 1.144 1.226 1.322 -13 -
.875 .845 .906 1,074 1.123 1.206 1.289 1.385 -14
.938 .907 .969 1.137 1.185 1.269 1.351 1.447 -15
1.000 .970 1.031 1.199 1.248 1.331 1.414 1.510- -16

1.062 1.032 1.094 1.262 1.310 1.394 1.476 1.572 -17

1.125 1.095 1.156 1.324 1.373 1.456 1.539 1.635 -18
1.188 1.157 1.219 1.387 1.435 1.519 1.602 1.697 -19
1.250 1.220 1.281 1.449 1.498 1.581 1.664 1.760 -20
1.312 1.282 1.344 1.512 1.560 1.644 1.727 1.822 -21

1.375 1.345 1.406 1.574 1.623 1.706 1.789 1.885 -22

1.438 1.407 1.469 1.637 1.685 1.769 1.852 1.947 -23
1.500 1.470 1.531 1.699 1.748 1.831 1.914 2.010 -24
1.562 1.532 1.594 1.762 1.810 ‘- 1.894 1.976 2.072 -25
1.625 1.595 1.656 1.824 1.873 1.956 2.039 2.135 -26

1.688 1.657 1.719 1.887 1.935 2.019 2.101 2;197 -27

1.750 1.720 1.781 1.949 1.998 2.081 2.164 2.260 -28
1.812 1.782 1.844 2.012 2.060 2.144 2.226 2;322 -29
1.875 1.845 1.906 2.074 2.123 2.206 2.289 2.385 -30
1.938 1.907 1.969 2.137 2.185 2.269 2.351 2.447 -31

2.000 1.970 2.031 2* 199 2.248 2.331 2.414 2.510 -32

NOTE: For collar selection, see NAS108O.

406.2
1-
 Downloaded from http://www.everyspec.com
.

.:. ..

MIL-STD-1759
10 JULY 1979

SECTION407

BOLT-LOCK,
TENSION,
100°HEAD[MS20426),
PULL-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS211STHIIU2122

lBt-
I

l===—
Tensile strength
Material Protective finish
(psi) min

Titanium alloy None “ 106,000

6AL-4V

TABLE 1. Pin-rivet, groove, configuration part numbers.

D ‘1 B Basic
Nom Min Max part
‘~
Size dia number

.164 .263 .055 4 NAS2115

.190 .316 .071 4 NAS2116
.250 ,428 .098 “4 NAS2118
.312 .508 .108 5 NAS2120
.375 .629 .137 5 NAS2122

~/ Number of locking grooves.

 Downloaded from http://www.everyspec.com

MIL-STD-1759 —
10JULY 1979

n
m
.-
0
m

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W4H-R- ------ - --.-fu~ NNNNN N

.
n

“N

n
n

t
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
d dd d.- -.---- -I--. (%J

A-
407.2
——
Downloaded from http://www.everyspec.com

----
MIL-STD-1759
10JULY 1979

SECTION408

BOLT-LOCK,
TENSION,
100°HEAD[MS20426],
STUMP-TYPE,
TITANIUMALLOY
APPLICABLE00CUMENT: NAS2315THRU 2322

100

#
Tensile strength
Material Protective finish (psi) min

1
Titanium alloy None 106,000
6AL-4V

part numbers,
TABLE I. Pin-rivet$ qroove$ configuration
I 1 I
D Basic
‘1 B
Nom Min part
Max number
size dia

I
.164 .263 055
●
NAS2315
.190 .316 .071 NAS2316
.250 .428 .098 NAS2318
.312 .508 .109 NAS2320
:375 I .629 I .137 I NAS2322
I 1 1

408.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE 11. NAS2315, 2316, 2318, 2320 and 2322 Dash numbers.

Grip range L
Grip
G G dash
Min Max .164 Dia .190 Dia .250 Ola .312 Old .375 Dla “Umber

.125 .095 .156 .125 .324 .373 .456 -02

.188 *157 .219 .188 .387 .435 .519 ;02
● ,;97 -03 .
.250 .220 .281 .250 .449 .498 .581 .664 .760 “04
.312 .282 .344 .312 .512 .560 .644 .727 .822 -05
.375 .345 .406 .375 .574 .623 .706 .789 .885 -06 .

.438 .407 .469 .438 .637 .685 .769 .852 .947 “07
.500 .470 .531 .500 .699 .748 .831 .914 1.010 -08
.562 .532 .594 .562 .762 .810 .894 .976 1.072 -09
.625 .595 .656 .625 .824 .873 .956 1.039 1.135 -lo
.688 .657 .719 ●688 .887 .935 1.019 1.101 1* 197 -11

.750 .720 .781 .750 .949 .998 1.081 1.164 1.260 -12
.812 .782 .844 .812 1.012 1.060 1.144 1.226 1.322 -13 -
,875 .845 .906 .875 1.074 1.123 1.206 ‘1.289 1.385 -14
.938 ,907 .969 .938 1.137 1.185 1.269 1.351 1.447 -15
,000 ●970 1.031 1.000 1.199 1.248 1.331 1.414 “ 1.510 -16

●
.062 1.032 1.094 1.062 1.262 1.310 1.394 1.476 1.572 -17
,125 1.095 1.156 1.125 1.324 1.373 1.456 1.539 1.635 -18
● 188 1.157 1.219 1.188 1.387 1.435 1.519 1.602 1.697 -19
,250 1.220 1.281 1.250 1.449 1.498 1.581 1.664 1.760 -20
,312 1.282 1.344 1.312 1.512 1.560 1.644 1.727 1.822 -21

,375 1.345 1.406 1.375 1.574 1.623 1.706 1.789 1.885 -22
,438 1.407 1.469 1.438 1.637 1.685 1.769 1.852 1.947 -23
,500 1.470 1.531 1.500 1.699 1.748 1.821 14914 2.CJ1O -24
,562 -25 .
1.532 1.594 1.562 1.762 1.810 1.894 1.976 2.072
.625 1.595 1.656 1.625 1.824 1.873 1.956 2.039 2.135 -26

,688 1.657 1.719 1.688 1.887 1.935 2.019 2.101 2.197 -27
-28 .
,750 1.720 1.781 1.750 1.949 1.998 2.081 2.164 2.260
,812 1.782 1.844 1.812 2.012 2.060 2.144 2.226 2,322 -29
.875 1,845 1.906 1.875 2 074
● 2.123 2.206 2.289 2.385 -30
.938 1.907 1.969 1.938 2.137 2.185 2.269 2.351 2.447 -31

t000 1.970 2.031 2.000 2.199 2.248 2.331 2.414 2.510 -32

NOTE : For collar selection, see NAS108O.

.-.- 408.2
11\
 Downloaded from http://www.everyspec.com

.:.

MIL-STD-1759
10 JULY 1979

SECTION409

BOLT-LOCK,
TENSION,
100°HEAD[MS24694),
PULL-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2105THRU2112

-1--
BP

I AH I

Tensile strength
Material Protective finish
(psi) min

Titanium alloy None 106,000

6AL-4V

TABLE I. Pin-rivet, groove, configuration part numbers.

D ‘1 B Baste
Nom Mln Max part
dia ‘1/
size number

.190 ,344 .083 4 NAS2106

..250 ,455 .109 4 NAS2108

~/ Number of locking grooves.

4(I9 .1
 Downloaded from http://www.everyspec.com

‘.

..

MIL-STD-1759
10JULY 1979

TABLE II. NAS2106 and 2108 Dash numbers.

.
Grip range .190 Dia .250 Dia Grip
G dash
Min Max L P L P number

.125 .095 .156 .358 1.25 -02

●188 .157 .219 .421 1.32 :499 1:45 -03
.250 ,220 .281 .483 1.38 .562 1.51 -04
.312 .282 .344 .546 1.44 .624 1.57 -05
●375 .345 .406 ●608 1.50 .687 1.64 -06

.438 .407 .469 .671 1*57 .749 1.70 -07

●500 ●470 .531 .733 1.63 .812 1.76 -08
.562 .532 .594 .796 1.69 .874 1.82 -09
.625 ●595 .656. .858 1.75 .937 1.89 -lo
.688 .657 .719 .921 1.82 .999 1.95 -11

750
● .720 .781 .983 1.88 1.062 2.01 -12
.812 .782 .844 1.046 1.94 1.124 2.07 -13
.875 .845 .906 1.108 2.00 1.187 2.14 -14
.938 .907 .969 1.171 2.07 1.249 2.20 -15
1.000 .970 1.031 1.233 2.13 1.312 2.26 -16

NOTE : For collar selection, see NAS108O. .

409.2
.-
 Downloaded from http://www.everyspec.com

.-

MIL-STD-1759
10JULY 1979

SECTION410

BOLT-LOCK,
TENSION,
100°HEAD[MS24694],
STUMP-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2306THRU 2312

l--G+

Tensile strength
Material Protective finish (psi) min
1 I

t
Titanium alloy None 106,000
6AL-4V

TABLE I. Pin-rivet, groove, configuration part numbers.

D A, B Basic
Nom Min Max part
size ciia number

.190 ,344 .083 NAS2306

.250 .455 .109 NAS2308
.312 ●574 .136 NAS231O
.375 .693 .164 NAS2312
 . Downloaded from http://www.everyspec.com
.
“.

MIL-STD-1759
10JULY 1979

TABLE II. NAS2306, 2308, 2310 and 2312 Dash numbers.

Grip range L Grip

G dash
Mi n Max .190 Dia .250 Dia .312 Dia .375 Dia number

.125 .095 .156 .373 .456 - - -02

●188 .157 .219 .435 .519 .602 .697 -03
.250 .220 .281 .498 .581 .664 .760 -04
.312 .282 ●344 .560 .644 ,727 .822 -05
.375 .345 .406 .623 .706 .789 .885 -06

.438 .407 .469 .685 .769 .852 .947 -07

.500 ,470 .531 .748 .831 .914 1.010 -08
.562 .532 ●594 .810 .894 .976 1.072 -09
.625 .595 .656 .873 .956 1.039 1.135 -lo
●688 .657 .719 .935 1.019 1.101 1.197 -11

.750 .720 .781 .998 1.081 1.164 1.260 -12

.812 .782 .844 1.060 1.144 1.226 1.322 -13
.875 .845 .906 1.123 1.206 1.289 1.385 -14
.938 ,907 .969 1.185 1.269 1.351 1.447 -15
1 000
● .970 1.031 1.248 1.331 1.414 1.510 -16

1.062 1.032 1 094

● 1.310 1.394 1.476 1.572 -17
1.125 1.095 1.156 1.373 1.456 1.539 1.635 -18
1.188 1.157 1.219 1.435 1.519 1.602 1.697 -19
1.250 1 220
● 1.281 1.498 1.581 1.664 1.760 -20
1.312 1.282 1.344 1.560 1.644 1.727 1.822 -21
I

1.375 1.345 1.406 1.623 1.706 1.789 1.885 -22

1.438 1.407 1.469 1.685 1.769 1.852 1.947 -23 I
1.500 1.470 1.531 1.748 1.831 1.914 2.010 -24
1.562 1.532 1.594 1.810 1.894 1.976 2.072 -25
1.625 1.595 1.656 1.873 1.956 2.039 2.135 -26

1 688
●
1.657 1.719 1.935 2.019 2.101 2.197 -27
1.750 1.720 1.781 1.998 2.081 2.164 2.260 -28
1.812 1.782 1.844 2.060 2.144 2.226 2.322 -29
1.875 1.845 1.906 2.123 2.206 2.289 2.385 -30
1.938 1 907
● 1.969 2.185 2.269 2.351 2.447 -31

2.000 1.970 2.031 2.248 2.331 2.414 2.510 -32

NOTE : For collar selection, see NAS108O.

410.2 J
 Downloaded from http://www.everyspec.com

-.

-----
MIL-STD-1759
10JULY 1979

SECTION411

BOLT-LOCK,
TENSION,
PROTRUDINGHEAD,
PULL-TYPE,
TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2005THRU 2012

lF1 B

..
..-- ..,.--

1: a------

I I
Tensile strength
hlaterial Protective finish (psi) min
1

Titanium alloy None 106,000

6AL-4V
I I

TABLE 1. Pin-rivet$ groove, configuration Part numberso

●

f) A B Basic
Nom Dia part
size number

,282 ,095
.164 .258 4 NAS2005
.085
.327 ,111
.190 4 NAS2006
.297 .099
.430 .147
.250 4 NAS2008
●390 .128

1/ Number of locking-. grooves.

-’

/’\,
All 1
—
Downloaded from http://www.everyspec.com

--,

MIL-STD-1759
10 JULY 1979

11.2
JA .-..
. —
Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION412

BOLT-LOCK,
TENSION,
PROTRUDINGHEAD,
STUMP-TYPE,TITANIUMALLOY
APPLICABLEDOCUMENT: NAS2205THRU2212

Tensile strength
Material “ Protective finish
(psi) min

Titanium alloy None 106,000

6AL-4V

TABLE 1. Pin-rivet, groove, configuration part numbers.

D A Basic
B
Nom Dia part
size number

.270 .072
.164 NAS2205
.255 .057
.317 .088
,190 NAS2206
.302 .073
.411 .113
.250 NAS2208
.396 .098
.575 140
.312 :125 NAS221O
,500
●628 .167
.375 NAS2212
.613 .152

Al Al? 1
 Downloaded from http://www.everyspec.com

MIL-STD”1759
10JULY 1979

TABLE 11. NAS2205, 2206, 2208, 2210 and 2212 Dash numbers.

Grip range L
Grip
G G dash
Min Max .164 Dia .190 Jia .250 Dia .312 Di~ .375 Dia number

.062 .031 ,094 .062 .262 .310 . -01

.125 .095 .156 .125 .324 373 .456 .539 .635 -02
.188 ,157 .219 .188 .387 .435 .519 .602 ,697 -03
.250 .220 .281 .250 .449 .498 .581 .664 .760 -04
.312 .282 .344 .312 .512 .560 .644 .727 .822 -05

,375 .345 .406 .375 .574 .623 ,706 .789 .885 -06
,438 .407 .469 ,438 .637 .685 .769 .852 *947 -07
.500 ,470 .531 .500 .699 .748 .831 .914 1.010 -08
.562 .532 .594 .562 .762 .810 .894 .976 1.072 -09
.625 .595 .656 .625 .824 .873 .956 1.039 1.135 -lo

●688 .657 ,719 .688 .887 .935 1.019 1.101 1.197 -11 ,
.750 .720 .781 .750 .949 .998 1.081 1.164 1.260 -12
.812 .782 .844 ,812 1.012 1.060 1.144 1.226 1.322 -13 ‘
,875 ,845 .906 .875 1.074 1.123 1.206 1.289 1.385 -14
.938 ,907 .969 .938 1,137 1.185 1.269 1.351. 1.447 -15

*000 .970 1.031 1 000

● 1.199 1.248 1.331 1.414 1.510 -16
.062 1.032 1,094 1.062 1,262 1.310 1.394 1.476 1.572 -17
.125 1.095 1.156 1.125 1.324 1.373 1.456 1.539 1.635 -18
,188 1.157 1,219 1.188 1,387 1.435 1.519 1.602 1.697 -19
.250 1 *220 1.281 1.250 1.449 1.498 1.581 1.664 1.760 -20

.312 1.282 1.344 1.312 1.512 1.560 1.644 1.727 1.822 -21
.375 1.345 1.406 1.375 1.574 1.623 1,706 1.789 1.885 -22
.438 1.407 1.469 1.438 1.637 1.685 1.769 1.852 1.947 -23
● 500 1.470 1.531 1.500 1.699 1.748 1.831 1.914 2.010 -24
.562 1.532 1.594 1.562 1.762 1.810 1.894 1.976 2.072 -25

.625 1.595 1.656 1.625 1.824 1.873 1.956 2.039 2.135 -26
.688 1.657 1.719 1.688 1.887 1.935 2.019 2.101 2.197 -27
.750 1.720 1.781 1.750 1.949 1.998 2.081 2.164 2.260 -28
.812 1.782 1.844 1.812 2.012 2.060 2.144 2.226 2.322 -29
.875 1.845 1.906 1.875 2.074 2.123 2.206 2.289 2.385 -30

.938 1.907 1.969 1.938 2.137 2.185 2.269 2.351 2,447 -31
,000 1.970 2.031 2.000 2,199 2.248 2.331 2.414 2.510 -32

NOTE : For collar selection, see NAS108O.

A..?.?
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION413

PIN,SWAGE LOCKING,
A-286CRES,
100°HEAD[MS20426],
TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS6955THRU 6962

-rt’tl
AH I

Tensile strength
Material Protective finish
(psi) min

Cres A-286 Passivate or 77,900

(AISI 660) per cadmium plate or
AMS 5735 or nickel-cadmium
5737 plating

TABLE 1. Pin-rivet, groove, configuration part numbers.

D Basic
‘1
Nom Mln .B part
“1/
size dia Max - number

.164 .263 .055 4 NAS6955

.190 .315 .072 4 NAS6956
.250 ,428 .099 4 NAS6958
.312 .508 .109 5 NAS6960
.375 .629 .138 5 NAS6962

~/ Number of loc!<inggrooves.

413.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

QJ
W4AQ
WILL
mm
-n=

Ou=
w= =
Luu
o-cm
u-<<

413.2
 Downloaded from http://www.everyspec.com

.:,

-. .
MIL-STD-1759
10 JULY 1979

SECTION414

PIN,SWAGE LOCKING,
A-286CRES,
100”HEAD[MS24694],
TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS6948THRU~52

m-

Tensile strength
Material Protective finish
(psi) min

Cres A-286 Passivate or 77,900

(AISI 660) per cadmium plate or
AMS 5735 or nickel cadmium
5737 plating

TABLE I. Pin-rivet, ctroove, configuration part numbers.

D Al Basic
Nom Min B part
size ul/
dia Max _ number

.190 .344 .084 4 NAS6946

.250 .455 .110 4 NAS6948
.312 ●574 .138 5 NAS6950
*375 .693 .166 5 NAS6952

1/ Number of locking grooves.

414.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

L
m

● ✎

m
IA
1-
0
z

414.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION415

Pli’i,
SWAGE LOCKING,A-286CflES,
100°SHEARHEAD,STUMP-TYPE
APPLICABLEDOCUMENT: NAS6974THRU 6982

LD
vi I

Shear strength
Material protective finish
(psi) min

Cres A-286 Passivate or 92,400

(AISI 660) per cadmium plate or
AMS 5735 or nickel-cadmium “
5737 plating

TABLE I. Pin-rivet, qroove, configuration part numbers.

D Al Basic
Nom Min B part
size dia Max number

.125 ,180 .037 NAS6974

.156 .220 ,043 NAS6975
.190 .262 .049 NAS6976
.250 ,346 .064 NAS6978
.312 ●417 .071 NAS6980
.375 .496 .082 NAS6982
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE II. NAS6974, 6975, 6976, 6978, 6980, and 6982 Dash numbers.

Grip range L

1
Grip
G dash
,156 Dia ,190Dia .25001 .312 Dia .375 Dia number
Min
I Max .125 Dia

062 ~/ .062 .201 .236 . -101

125 .063 .125 .263 .298 .323 .376 02
188 .126 .188 .326 .361 - .386 .439 . i58 .;01 03
250 .189 .250 .388 .423 .448 ,501 .520 .563 04
312 .251 .312 .451 .486 .511 .564 .583 .626 05

375 .313 .375 .513 .548 .574 .626 .645 .688

438 .376 .438 .576 .611 ,637 .689 .708 .751 &
500 .439 ● 500 ,638 .673 .699 .751 .770 .813 08
562 .501 .562 .701 .736 .762 .814 .833 .876 09
625 .563 .625 .763 .798 .824 .876 .895 .938 10

688 .626 ●688 .826 .861 .887 .939 .958 1.001 11

750 .689 .750 .888 .923 .949 1.001 1.020 1.063 12
812 .751 .812 .951 .986 1.012 1.064 1.083 1.126 13
875 .813 .875 1.013 1.048 1.074 1.126 1.145 1.188 14
938 .876 .938 1.076 1.111 1.137 1.189 1.208 1.251 15

000 ●939 1.000 1.138 1.173 1.199 1.251 1.270 1.313 16

062 1.001 1.062 1.261 1.314 1.333 1.376 17
125 1.063 1.125 1.323 1.376 1.395 1.438 18
188 1.126 1.188 1.386 1.439 1.458 1.501 19
250 1.189 1.250 1.448 1.501 1.520 1.563 20

312 1.251 1.312 1.511 1.564 1.583 1.626 21

375 1.313 1.375 1.574 1.626 1.645 1.688 22
438 1.376 1.438 1.637 1.689 1.708 1.751
500 1.439 1.500 1.699 1.751 1.770 1.813 ::
562 1.501 1.562 1.762 1.814 1.833 1.876 25

625 1.563 1.625 1.824 1.876 1.895 1.938

688 1.626 1.688 1.887 1.939 1.958 2.001 ;;
750 1.689 1.750 1.949 2.001 2.020 2.063 28
812 1.751 1.812 2.012 2.064 2.083 2.126 29
875 .1.813 1.875 2.074 2.126 2.145 2.188 30

938 1.876 1.938 2.137 2.189 2.208 2.251 31

000 1.939 2.000 2.199 2.251 2.270 2.313 32

~/ Minimum grip for -01 varies with material to be fastened together.

NOTES: 1. For collar selection, see NAS108O.

2. Add “C” after basic part number for Cadmium plate.
30 Add “N” after basic part number for Nickel-Cadmium plate,
 Downloaded from http://www.everyspec.com

-. MIL-STD-1759
10 JULY 1979

SECTION416

PIN,SWAGE LOCKING,
A-286CRES,
100°SHEAR/TENSIONHEAD,PULL-TYPE
APPLICABLEDOCUMENT: NAS7004THRU 7012

-r I B-
G——

4) ‘“’t’ll
vI LD

l-- L- I

Shear/
Protective tension
Material finish strength
(psi) min

Cres A-286 Passivate or 70,500

(AISI 660) cadmium plate or
per AMS 5735 nickel cadmium
or 5737 plating

TABLE I. Pin-rivet, groove, configuration part numbers.

D
Nom
‘1
Min B
Basic
part
size dia Max number

.125 .190 .041 NAS7004

.156 .240 .051 NAS7005
.l$I’ .288 .060 NAS 7006
,250 .379 .078 NAS7008
.312 .470 .095 NAS701O
● 375 .561 .111 NAS7012

416.1
‘A
 Downloaded from http://www.everyspec.com

MIL-S7-D-1759
10JULY 1979

w
6
m
“n

.-
E
-u
“n

L
aJ

f
c

L
m
mn

%’
n
L
a

. . .
-Wm
..
(A
w

416.2
.- ,s+
n
 Downloaded from http://www.everyspec.com

L MIL-STD-1759
10 JULY 197’9

SECTION417

PIN,
“SWAGELOCKING,A-286CRES,
PROTRUDINGHEAD,SHEAR/TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS7014THRU 7022
G

1 B
F7 ----
------- ..-

=:: Illmii
D
z ------

Shear/
Protective tension
Material finish strength
(psi) min

Cres A-286 Passivate or 70,500

(AISI 660) cadmium plate or
perAMS 5735 nickel cadmium
or 5737 plating ~

TABLE I. Pin-rivet, qroove, configuration part numbers.

D Basic
Nom A B part
size Dia number

.193. .065
.125 NAS7014
.177 .059
.238 .077 NAS7015
.156
.219 .070
x .086 NAS7016
.190
.268 .079
.380 .771
.250 NAS7018
●354 .104
.475 r
.312 NAS7020
.443 ,130
.569 .164
.375 NAS7022
.533 .157

417.1
 Downloaded from http://www.everyspec.com

.:.

MIL-STD-1759
10JULY 1979

m
k
m
.

------ --.-4- -- -o-N(wNN N

*
.-

----- ----- ---- --NNNN N

n
o
Ln
N

.,. . . . . . . . . . . . . . . . . .
d--- dti&N” N’ “ “
tummmm “ ‘ “
mm-mm mmmmm mmmmm mm

-1
. . . . . . . . . . . . . . . .
---

a
aJ U& .
m LL
a
n
w Uv

.
.

w
m
c
m
L
----- ----- ----- .6A

n
F

----- ----- ----- - . . .

-$Nm

..
La
a w

417.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION418

PIN,SWAGE LOCKING,
A-286CRES,
PROTRUDINGHEAD,SHEAR,STUMP-TYPE
APPLICABLEDOCUMENT: liAS6984
THRU 6992

f -,
+
\/ \/

@-

Shear strength
Material Protective finish (psi) min

Cres A286 Passivate or cad- 92,400

(AISI 660) mium plate or
per AMS 5735 nickel cadmium
or 5737 plating

TABLE 1. Pin-rivet, qroove, configuration part numbers.

Basic
D
A B part
Nom
number
size Dia

.195 .040 “ NAS6984

.125
.181 ,028
.249 .048
.156 NAS6985
.235 .036
.302 .056
.190 NAS6986
.288 .044
.377 .070
.250 .058 NAS6988
.363
.471 .079
.312 NAS6990
.455 .067
.565 .089
.375 NAS6992
.549 .077
----
 Downloaded from http://www.everyspec.com

=.

-
P!IL-STD.1759
1(3JULY 1979

TABLE II. NAS6984, 6985, 6986, 6988, 6990 and 6992 Dash numbers.

Grip range L
—. Grip
G dash
Mln Max .250 Of .312 Dli .375 Di( numoer

,062 . .062 .201 .236 .261

.125 .063 .125 .263 .298 ,323 .;76 .;95 .~38
.188 ,126 ,188 .326 .361 .386 ,439 .458 .501
.250 .189 .250 ,388 ,423 ,448 .501 .520 ,563
.312 .251 .312 ,451 ,486 .511 ,564 .583 .626

.375 .313 .375 .513 .548 .574 .626 .645 .688

.438 .376 .438 .576 .611 ,637 .689 .708 .751
.500 .439 .500 .638 .673 .699 .751 .770 .813
.562 ,501 .562 .701 .736 ,762 ,814 .833 .876
.625 .563 ,625 .763 .798 .824 .876 .895 .938

.688 .626 ,688 .826 .861 .887 .939 .958 1.001

● 750 .689 .750 ,888 .923 ,949 1.001 1.020 1.063
.812 .751 .812 .951 .986 1.012 1.064 1.083 10126
.875 .813 .875 1.013 1.048 1.074 1.126 1.145 1.188 -
.938 .876 .938 1.076 1.111 1.137 1.189 1.208 1.251

1.000
1.062
1.125
.939
1.001
1.063
1 000
●

1,062
1.125
-1-1
1,138

.
1.173 1.199
1.261
1.323
1.251
1*314
1.376
1,270
1.333
1.395
-1.313
1.376
1.438
1.188 1.126 -1.188 1.386 1.439 1.458 1.501
1.250 1.189 1.250 1.448 1.501 1.520 1.563

1.312 1.251 1.312 . 1.511 1.564 1.583 1.626

1.375 1.313 1.375 - 1.574 1.626 1.645 1.688
1.438 1.376 1.438 1.637 1.689 1.708 1.751
1.500 1.439 1.500 1.699 .1.751 1.770 1.813
1.562 1.501 1.562 1.762 1.814 1.833 1.876

1.625 1.563 1.625 I 1.824 1.876 1.895 1.938

1.688 1.626 1.688 1.887 1.939 1.958 2.001
1 750
● 1.689 1.750 1.949 2.001 2.020 2.063
1.812 1.751 1.812 . 2.012 2.064 2.083 2.126
1.875 1.813 1.875 - 2.074 2.126 2.145 2.188

1.938 1.876 1.938 2.137 2.189 2.208 2.251

2.000 1.939 2.000 2.199 2.251 2.270 2.313

NOTES: 1. For collar selection, see NAS 1080.

2. Add “C” after basic part number for Cadmium plate.
3. Add “N” after basic part number for Nickel-Cadmium plate.

418.21
 Downloaded from http://www.everyspec.com

.
.
.-
.:.

MIL-STD-1759
10 JULY 1979

SECTION419

PIN,
SWAGE LOCKING,
A-286CRES,
PROTRUDING
HEAD,TENSION,PULL-TYPE
APPUCABLE OOCUMENT: NAS6965THRU 6972
~—G +

-.%U.:-S

1%a “-----

Tensile strength
Material Protective finish (psi) min
I
I
1
Passivate or cad- 77,900
Cres A-286
(AISI 660) per mium plate or
AMS 5735 or nickel-cadmium
I 5737 I plating
1 I
1-
TABLE Pin-rivet, groove, configuration part numbers.

D Basic
Nom “ A part
size Oia B “l_/ number

.282 .095 4 NAS6965

.164
.258 ‘.085
.327 ●111 4
NAS6966
.190
●297 .099
.430 .147 4 NAS6968
.250
6390 .128
.535 ,184 ~ NM 6970
.312 .158
.485
.655 .224 5 W 6972
● 375
.595 .194

~ Number of locking grooves.

m. K Ala 1
 Downloaded from http://www.everyspec.com

.-<.

MIL-STD-1759
10 JULY 1979

s
m
a

u
-

419.2 ●✎ ✍
 Downloaded from http://www.everyspec.com
.

. .

-----

MIL-STD-1759
10 JULY 1979

SECTION420

PIN,SWAGE LOCKING,
108KSISTEEL,
100°SHEAR/TENSIONHEAD,PULL-TYPE
APPLICABLEDOCUMENT: HAS7024THRU 7032

LD
VI

Shear/
Protective tens 1on
Material finish strength
(psi) min

Alloy steel Cadmium plate or 42,300

(AISI-8740) nickel cadmium
plating

TABLE I. Pin-rivet, qroove, cOnfiwratiOn part numbers.

——.

D Basic
‘1
Nom Mln B part
size dia Max number

.125 .190 .041 NAS7024

.156 .240 .051 NAS7025
.190 .289 .060 NAS7026
.250 ● 379 .078 NAS7028
.312 .471 .095 NAS7030

.375 .562 .111 NAS7032

-i A
 .
Downloaded from http://www.everyspec.com
.
. .

-.

MIL-STD-1759
10 JULY 1979

n --

.. -
z

420.? ..
 Downloaded from http://www.everyspec.com

..
-“.

.-.

MIL-STD-1759
10 JULY 1979

SECTION421

PIN,SWAGE LOCKING,
108KSISTEEL
PROTRUDINGHEAD,SHEAR/TENSION,
PULL-TYPE
APPLICABLEDOCUMEH~ NAS7034THFIU7042

7
B
1 F

Shear/
Protective tension
finish strength

II
Material
(psi) min

Alloy steel Cadmium plate or 42,300

(AISI 8740) nickel cadmium
plating .

TABLE I. Pin-rivet, qroove, configuration part numbers.

Basic
D
A B part
Nom
Dia number
size

.193 .065 NAS7034

.125
.177- .059

.156
I .238
.219
.077
.070
NAS7035

.190
I .288
.268
.086
.079
NAS7036

I .380
1

.111
.250 NAS7038
.354 .104
.475 .137
.312 NAS7040
,443 .130
.569 .164
.375 NAS70d2
.533 .157
+-
 Downloaded from http://www.everyspec.com

-.

MIL-STD-1759
10 JULY 1979

n
-

.
z
o
2
z
w
aJ
vl

Um
aJn

. .
-w

..
u-i
UJ
+
0
z

421.2
 Downloaded from http://www.everyspec.com

.-.

‘--- -

MIL-STD-1759
10 JULY 1979

SECTION422

PIN,SWAGE LOCKING,
ALUMINUM ALLOY,
100°HEAD[MS20426],
TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS1535THRU 1542

-/5;1
// +
+
t ‘/

@
I

Tensile strength
Material Protective finish (psi) min
I

Anodize or chemical 42,100

Aluminum
alloy 7075 surface treatment

TABLE 1. Pin-rivet, qroove~ confiwrationg

Basic
‘1
Nom Min B part
size dia Max number

.164 .263 .055 NAS1535

.190 .316 .071 NAS1536

.250 .428 .098 NAS1538

 . —
Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

t- 422.2
 Downloaded from http://www.everyspec.com

-..
MIL-STD-1759
10JULY 1979

SECTION423

PIN,
SWAGE LOCKING,
ALUMINUMALLOY,
100°HEMI[MS24694],
TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS1516THRU 1522

&G-
B

I t .

/’
100°

[
q.--+ .

,
Tensile strength
Material Protective finish (psi) rnin
k

Aluminum alloy Anodize or chemical 42,100

7075 surface treatment
●
4

TABLE I. Pin-rivet, qroove, configuration.

D Al Basic
Nom Min ~ B part
size dia Max number

.190 .344 ,084 NAS1516

L .250 .455 ,110 NAS1518

.312 .574 .137 NAS1520

 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE II. NAS1516, 1518 and 1520 Dash numbers.

Grip range .190 Dia .250 Dia .312 Dia

Grip
G dash
Min Max L P P L P number

.125 .095 .156 .358 1.44 .437 1.88 - - -02

● 188 .157 ,219 .421 1.56 .499 2.00 .568 1.88 -03
.250 .220 .281 .483 1.69 .562 2.12 .631 2.00 -04
.312 .282 .344 .546 1.81 .624 2.25 .693 2.12 -05
.375 .345 .406 .608 1.94 .687 2.38 .756 2.25 -06

.438 .407 .469 .671 2.06 ●749 2.50 .818 2.38 -07
.500 .470 .531 .733 2.19 .812 2.62 .881 2.50 -08
.562 .532 ,594 .796 2.31 .874 2.75 ,943 2.62 -09
.625 .595 .656 .858 2.44 ,937 2.88 - 1.006 2.75 -lo
●688 .657 .719 .921 2.56 ,999 3.00 1.068 2.88 -11

,750 .720 ,781 .983 2.69 1.062 3.12 ;.131 3.00 -12
,812 .782 .844 1.046 2.81 1.124 3.25 1.193 2.31 -13
,875 .845 .906 1.108 2.34 1.187 2.50 1.256 2.38 -14
,938 .907 .969 1.171 3.06 1.249 2.56 1.318 2.44 -15
v000 .970 1.031 1.233 3.19 1.312 2.62 1.381 2.50 -16

.062 1.032 1.094 - - 1.374 2.69 - - -17

.125 1,095 1.156 - - 1.437 2.75 - - -18
.188 . 1.157 1.219 - - 1*499 2.81 - - -19
.250 1.220 1.281 - 1.562 2.88 - -20
.312 1.282 1.344 - 1.624 2.94 - -21

.375 1.345 1.406 - . 1.687 3.00 - -22

.458 1.407 1.469 - - 1.749 3.06 - : -23
.500 1.470 1.531 - - 1.812 3.12 - - -24
.562 1.532 1.594 - - 1.874 3.19 -1 - -25
.625 1.595 1.656 - - 1.937 3.25 - - -26

● 688 1.627 1.719 - - 1.999 3.31 - -. -27

.750 1.720 1.781 - 2.062 3.38 - -28
.812 1.782 1.844 - : 2.124 3.44 - -29
.875 1.845 1.906 - - 2.187 3.50 - -30
.938 1.907 1.969 - - 2.249 3.56 - - -31

.000 1 970
● 2.031 - - 2.312 3.62 - - -32

NOTE : For collar selection, see NAS108O.

423.2

(“>1 I
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION424

PIN,SWAGE LOCKING,
ALUMINUM ALLOY,
100°HEAD[MS20426],TENSION,
STUMP-TYPE
APPLICABLEDOCUMENT: NAS6915THRU 6922

Tensile strength
Material Protective finish (psi) min

Aluminum alloy Anodize or chemical 42,100

7075 surface treatment

TABLE 1. Pin-rivet, groove, confj9uratiOn part numbers.

D Al Basic
Nom Min B part
size dia Max number

.164 .263 .055 NAS6915

.190 m320 .071 NAS6916

.250 .433 .098 NAS6918

.312 .513 .109 NAS6920

.635 ,137 NAS6922

.375
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

TABLE 11. NAS6915, 6916, 6918, 6920, and 6922 Dash numbers.

Grip range L
# Grip
dash
G Dia ●375 Dja
Min Max .164 Dia .190 Dia .2S0 Dia .312 number
,
.125 .095 .156 .324 .386 ,456 - -02
.188 .157 .219 .387 .448 .519 .602 ● ;97 -03
.250 ● 220 .281 .449 .511 .581 .664 .760 -04
.312 .282 .344 .512 .573 .644 .727 .822 -05
.375 .345 .406 ,574 .636 .706 .789 .885 -06

.438 .407 .469 .637 .698 .769 ,852 ●947 “07

.500 .470 .531 .699 .761 .831 .914 1.010 -08
.562 .532 .594 .762 .823 .894 ,976 1.072 -09
.625 .595 .656 .824 .886 .956 1.039 1.135 -10
.688 .657 .719 .887 .948 1.019 1.101 1.197 -11

.750 .720 .781 .949 1.011 1.081 1.164 1.260 -12

.812 ,782 .844 1.012 1.073 1.144 1.226 1.322 -13
.875 .845 .906 1.074 1.136 1.206 1.289 1.385 -14
-
.938 .907 .969 1.137 1.198 1.269 1.351 1.447 -15
1.000 .970 1.031 1.199 1.261 1.331 1.414 1.510 -16

1.062 1.032 1.094 1.262 1.323 1.394 1.476 1.572 -17

1.125 1.095 1.156 1.324 1.386 1.456 1.539 1.635 -18
1.18E 1.157 1.219 1.387 1.448 1.519 1.602 1.697 -19
1.250 1.220 1.281 1.449 1.511 1.581 1.664 1.760 -20
1.312 1.282 1.344 1.512 1.573 1.644 1.727 1.822 -21

1.375 1.345 1,406 1.574 1.636 1.706 1.789 1.885 -22

1.438 1.407 1.469 1.637 1.698 1.769 1.852 1.947 -23
1.500 1.470 1.531 1.699 1.761 1.831 1.914 2.010 -24
1.562 1.532 1.594 1.762 1.823 1.894 1.976 2.072 .25
1.625 1.595 1.656 1.824 1.886 1.956 2.039 2.135 -26

1.688 1.657 1.719 1.887 1,948 2.019 2.101 2.197 -27

1.750 1.720 1.781 1.949 2.011 2.081 2.164 2.260 -28
1.812 1.782 1.844 2.012 2.073 2.144 2.226 2.322 -29
1.875 1.845 1.906 2.074 2.136 2.206 2.289 2.385 -30
1.938 1.907 1.969 2.137 2.198 2,269 2.351 2.447 -31

2.000 1.970 2.031 2.199 2.261 2.331 2.414 2.510 -32

NOTE : For collar selection, see NAS108O.

424.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION425

PIN,SWAGE LOCKING,
ALUMINUM ALLOY,
PROTRUDINGHEAD,TENSION,PULL-TYPE
APPLICABLEDOCUMENT: NAS1525THRU 1532

G~

-I F,

Tensile strength
Material Protective finish (psi) min

Aluminum alloy Anodize or chemical 42,100

7075 surface treatment

TABLE I. Pin-rivet, groove, confiquratjono

.

D Basic
Nom A B part I
Dia number I
size

I
.282 .095 NAS1525
.164
.258 .085

.327 .111
.190 NAS1526
.297 .099

,250 .430 .147

NAS1528
.390 .128

.535 ,184
.312 NAS1530
.485 ,158

.655 .224 NAS1532

.375
.595 .194
 Downloaded from http://www.everyspec.com

..

MI L-STD-1759
10 JULY 1979

N
m
Ln
u

u
 Downloaded from http://www.everyspec.com

----
MIL-STD-1759
10JULY 1979

SECTION426

PIN,SWAGE LOCKING,
ALUMINUM ALLOY,
PROTRUDINGHEAD,TENSION,STUMP-TYPE
APPLICABLEDOCUMENT: NAS1555THflU1562

k----l+

Tensile strength
Material Protective finish
(psi) min
I 1

t I I
Aluminum alloy Anodize or chemical 42,100
7075 surface treatment

TABLE I. Pin-rivet, groove, configuration part numbers.

D Basic
Nom A B part
size Dia number

.317 .088 NAS1556

.190
.302 ,078

●XO .411 .113 NAS1558

.396 .103
.~i5 .152
.312 NAS1560
.500 ,142

426.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

TABLE II. NAS1556, 1558 and 1560 Dash numbers.

Grip range L
* Grip
G dash
Min Max .190 Dia .250 Dia .312 Dia number

.062 .031 .094 .323 -01

.125 .095 .156 .386 .4;6 .539
- -02
Q188 .157 .219 .448 .519 .602 -03
.250 .220 ,281 .511 .581 .664 -04
.312 .282 ●344 .573 .644 .727 -05

.375 .345 .406 .636 .706 .789 -06

.438 .407 ,469 .698 .769 .852 -07
●500 .470 .531 .761 .831 .914 -08
.562 .532 .594 .823 .894 .976 -09
.625 ●595 .656 .886 .956 1 039● -lo

●688 .657 .719 .948 1.019 1.1O1 -11-

.750 .720 .781 1.011 1.081 1.164 -12
.812 .782 .844 1.073 1.144 1.226 -13
.875 .845 .906 1.136 1.206 1.289 -14
.938 .907 .969 1,198 1.269 1.351 -15

1 000
● .970 1.031 1.261 1.331 1.414 -16

NOTE : For collar selection, see NAS108O.

426.2
t-
 Downloaded from http://www.everyspec.com

->.
MIL-STD-1759
10 JULY 1979

SECTION427

PIN,SWAGE-LOC%ING,BRAZIERHEAD,STRAIGHTSHANK,
SIXLOCKINGGROOVES.ALUMINUM ALLOY,
CORROSIONRESISTANTSTEELAND CARBONSTEEL
APPLICABLEDOCUMENT: MIL-P~23469/2

TYPE I - SIX LOCKING GROOVE PINS

Shear strength Class

Material Protective finish
(psi) min

Aluminum alloy Not specified 26,900 1

6061

Cres #10 Not specified 68,400 2

AISI 304
AISI 305

Carbon steel Not specified 61,600 3

CI035, C1038,
C1041, C1OB18,
C1OB23 ●

TABLE I. Pin-rivet, groove, configuration.

II
D
Nom A c
dia ‘Dia

I .188
●394
.356
.173
.125

1°250
I:M .181
.201

,375 .787
.713
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

.
v

--i--=

u
Ill 81* Ilttlll II I

--- --

J
N~u ma- male l-mm em@ A -@a) U)a:
ON-
000 000 ---

--- Zz;
Oco 00- *-- ---~ ~
Waa
000
WWw Waw was
0C% -----
000 000

~NN
18111
000
NNN
000
NNW
1111111
000
NNA NNN
11
z 1
NNCW (wNN NN
Ill Illlt

N~e ma- amo -Wm gm~ 1- Oml-r

000 000 0=- --- --- - ---
boaw
000
WWU2
000
Wtoa
000
Wwa
000
tows
000
w
0
000
..-
---
Ill

L
k~N ef%U! NV
~ON mem r-m

N N
,...
F-NN NNN
. .
NN
. .

I I

mom Omo UIO

ONU)

. . . z~
NWI-
x ...
-NI- u-l@-
..

;1=
.- r ‘“ “ “ “ “ ‘:
I 1

427.2
 Downloaded from http://www.everyspec.com

.. MIL-STD-1759
10JULY 1979

SECTION428

PIN,SWAGE-LOCKING,
BUTTON HEAD,STRAIGHTSHANK,
SIXLOCKINGGROOVES AND MULTIPLELOCKINGGROOVES,
ALUMINUM ALLOY,CORROSIONRESISTANTSTEELAND C8RB0NSTEEL
APPLICABLEDOCUMENT: MH-P=23469/4

TYPE I- SIX LOCKING GROOVE PINS

~z~
-q c [+-Y--
I I
I

-----

TABLE 1. Pin-rivet, qroove, configuration.

D
Nom A c
dia Dia

.135
.188
I .342
.312 .145

.458 .181
.250
I .418 .195

.312
I .571
.521
.244
.224
.686 .269
.375 I .626 .293

428.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

Shear strength
Material Protective finish Class
(psi) min

1
Aluminum alloy
6061
Not specified
I 26,900
I
Cres #10 Not specified 68,400 2
AISI 304
AISI 305
Carbon steel Not specified 61,600 3
CI035, C10389
C1041, C1OB18,
C10B23

TABLE II. M23469/4 Dash numbers.

-
.188
dfdmeter I bsn mmmer .2S0
dlmetrr !bSn numoe”
I I I
~ Caroon
Grip range
I
x v
iz Al . Cr?S‘ICdroon
steel
Grlpranae ; x / v ; Z- A1 ~ Cres , *te@l

21Cl~SS
J
IOn

.062
i .%x ‘
I .326 1.50 .;CsG~
I I c;~ss
Ili cldSS 2! c;&SS 3 Min : Ml I class ! :cldSS

.12s
.187
I
.187
.250
.312 ~
.C6i ;
.125
.187
\
I
.389
.451
\ -206CZ
1.56
1.63 -10604
! .062 .396‘;.631-I080Z
!-10602.062~ .187
-1C603 I -206C3 1 :j;g~
-20604
.?(IS2Z
-30802
.125
.107
I
,
.2SC
.312
,
i
.l~~
.187
459
.521
I 169
I 1.75
-10803
\ -108I34
-20e03 I -30803
-20804 i .30804
i
.250 i .375 f .250 / .514 ‘ 1.69 -10605 -20605 , -30605 .25@ ! ,375 ‘ .25’2 , .584 ‘ : e) -10805 -20805 -30805
,312 I .437 f .312 i .576 1.75 -10606 I -20606 I -30606 .312 .437 .3]2 ,646 1.58 I -10806 -20806 . -30806
.375 i .500 .375 .639 -10607 -20607 I -30607 .3?5 , .5C0 .375 .709 , 1 94 : -10807 -20807 -30807
! ; ‘“81
.437 : .562 i .437 .701 , 1.88 ! -10603 -20608 -30608 .437 .5&2 437 77’ 2.CO -10/?08 -20808 I -30808
.500 ~ .625 1.94 -10609
-20609 I -30609 .500 .625 .5C9 .834 2.06 -10809 .20809 I -30809
.562 : .687 I :% I .826
“764 2.03 -1061O -20610 ‘ -30610 .562 .687 .S62 .896 2.13 i -108)0 I -20810 -30810
I
I
.625 .750 .625 .889 2.06 -1061} -20611 ‘ -30611 625 .750 f .625 : .959 2.19 -10811 -20811 -30811
.687 .812 .687 I .951 2.)3 [ -10612 I -?061? ! -30612 .687 ! .812 .687 I 1.021 , 2.2S -10812 ! -20812 ! -30812
.750 .875 .750 , 1.014 , 2.19 -10613 ! -20613 : -30613 .750 .875 .750 1.084 ; 2.31 -10813 I -20813 ~ -30813
I
[ I I
.812 .812
t
1 1.076
: 225
-10614 -296)4 , .30614 .812 I .937 ( .812 ‘ 1.146 I2.38 -108I4 : -20814 : -30814
.875 i l:i;i ‘ .875 ~ 1.139 ; 2:31 -10615 I -29615 -30615 .875 I 1,000 i .875 ; 1.209 2.44 -10815 -20815 I -30815
.937 j 1.062 .937 1.201 ; 2.38 -10616 I -20616 -30616 .937 1.062 1 .937 1 1.271 2.50 -10816 ‘ -20816 I -30816
I I i
1.I-SOO1 1.125 , 1.000 ~ 1.264 ! 2.44 [ -10617 ‘ -20617 ~ -30617 1.WO 1.12: I.000 ! 1.336 “ 2.56 I -10817 -20817 ‘ -30817

.312 diameter I
04sn number .3?5 dfmeter I Oa$h mmmr

1 I 1 I
I ~ :;w:n Carbon
Grip rmae xl Grlo ranqe \ x ‘ Y z ~ Al ‘ Cres
s tee I
~
Mln 1 nsl
ly~z~A’!cres
I class : 1 class 21 class 3 Hin ‘ WI ,C)dss 1! class 2! C)4S$ 3

.125 1 ,125 \ .570 1 1.97 -I1OO4 ‘ -21004 i -31004 m: ~ .375 ~ 125 ‘ .658 ‘ 2.2s -11204 ! -21204 i -31204
.250 I :% .250 ‘ .695 I 2.09 I -11006 I .21006 i -31006 .500 I .250 .783 2.38 / .11206 -21206 ‘ -31206
.375 .625 .375 82C ?.:2 ‘ -llrm -21008 -3100a .375 .625 375 .908 2.50 -1;208 -21208 I -31208
1! I
.500 75Q I g~ 945 2.34 -l IOIC -21010” -3131C ~.C33 2.63 -11?10 -21210 -31210
500 .753 .500
.025 ,$,: / :.370 - :7 -1101: 1,15!3 2.?5
.625 -?lclz -IIC12 .52: .275 .625 -112:2 .21212 -31212
.750 :.200 .:59 :.!95 ::59 , -::C;: -;::14 -31014 .750 I mc ?50 :.283 2,W -1;214 -21214 -31214
I
.875 ‘.125 1 .875 ].32’3 ?-;2 , -;;o16 .~[316 .]!o]~ .875 1,!:5 875 1.408 I.CO -11216 -21216 .31216
1 .’.)00 1.:50 I 1.000 I.<45 ~,~~ -“\z!2 ‘ -;),3;
? -j1016 ;.CCC 1.:59 !300 :.s33 j.~~ -; 1:18 -2121e -3t2te
-

428.2
 Downloaded from http://www.everyspec.com

.-

->.- MIL-STD-1759
10 JULY 1979

TYPE II - MULTIPLE LOCKING GROOVE PINS.

-- .-.. — ...
-. .-

- .-.. %.---
..

‘u

TABLE I. Pin-rivet, qroove, configuration.

D
Nom A c
dia Dia

.938 .302
.500
.875 .330

1.187 .378
.625
1.094 .415

1.438 .455
.750
1.328 .500

1.656 .531
● .875
1.547 ,578

1.906 .591
1.000
1,781 . .640

428.3
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

I-lu

IN
t--

z’ i
I

. .
-- --
000 000 Oci ‘1 00 Oco Ca
Omo mom WI $.00 :n~ c L?
m-o rwmP- 8;I =; 0 .%
. . . . . . -0
. . . . .
--- NW
1 ?’ --- NtN

,-—; I

.+
--- -N

i
v~N
oo -
*OW
-NN N-
CON
.;

Loww aou a-
-----
mmtm
118$11
mm-
- --
mrw
81 LI
I

I
l--
-Ifl
m ----- - --
819111 II
<
u

I
N

--- . .
fWNN Nfi

. . . . . . . .
-- --

--- N$W

--- -N
=!””’ ---“_:
I
-

428.4
 Downloaded from http://www.everyspec.com

--

MIL-STD-1759
10JULY 1979

SECTION429

PIN,S’iA/AGE-LOCXING,
FLAT90°COUNTERSUNKHEAD,ST3AUNIT
SHANK,SIXLOCXINGGROOVESANO MULTIPLELOCXINGGROOVES,
ALUMINUM ALLOY,CORROSIONRESISTANTSTEELAND CARBON STEEL~
APPLICABLEDOCUMENT: MIL-P-23469/6

Shear strength
Material Protective finish Class
(psi) min

Aluminum alloy Not specified 26,900 1

6061
Cres #10 Not specified 68,400 2
AISI 304
AISI 305
Carbon steel Not specified 61,600 3
C1035, C1038,
clo41, C70B18,
CIOB23

429.1
A
 Downloaded from http://www.everyspec.com
.

.:

MIL-STD-1759
10JULY 1979

TYPE I - SIX LOCKING GROOVE PINS

—A c pm9-

TABLE I. Pin-rivet, groove, configuration.

D
Nom A c
dia Dla

.354 .078
.188
.328 ,085
.473 .104
.250
.437 .113

.589 .131
.312
.547 .140
,709 .155
●375
.656 .168

e
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

111181 1811111 II Iltll II

—
~1*
1- N
01
J--- N

c:
‘a)L
s:
ul
w
Q =1
VJ

t.
w
m
m
ml v *1 v .
“u
a_ — :- U

1-

—
I i
N k

t-

--
L-

I
I

IN

,1,11! 1111, , !,,

,- vto= ONU o=
It/’l Ooc --- --
C=3
----- —
cc=

----- ---
0=

--- I
1198111 108148, a 01,4111

l’-
I
N

1
1
I

1> ----

mom 0U70 Lnc

N@!+ oNn A.=
x -mm Ins- =0
,.. . . . . .

--

I i

42!?.3
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

TYPE II - MULTIPLE GROOVE PINS.

.
x--l
.n I
r
90°
- . .- . .-
-------

\ w-

TABLE I. Pin-rivet, qroove, configuratlono

D
Nom A ‘c
dia Dia

945
● .225
.500
.875 .239
1.183 .284
.625
1.093 300
●

1.417 .340
.750
1.312 .360
1.655 .396
.875
● .420
1.895 .453
1.000
1.750 ,481

429.4
 Downloaded from http://www.everyspec.com

.-

MIL-STD-1759
10 JULY 1979

.1 I(WI
m
*OU mm
-SJN
NNNJ
mmm
Rz
mm
-----
111 II

al .. . . . . .

CJ’
ml -1-! ---

=! II
x Oco
000 oca
Lnotn
“~ l% 000
Cac
Occ
d-icu-i
g ,e ONA
. . .
%S.v
. ,,
g,; Owtn
,,..
-c%
. . . . . —..
c, --- -mm
;=
/-J,
--- .mJm --- NW
“b —.
I
---- -
Oao bng
Cewm
. . . . .

Oex N
NINAI m
aaa a
---
mm- m
111 1 I,#,,, ,

1
----
I .-H
I I a I
x ---
.-. =Cc
T mca C1.nc z
-J;: f=o
. .
-. U7ho
. . .
(w
.
al
1 -- --AIN
$U
L

a t
-fc
Ll -
,. . . . .
Oz
--- N

-L

429,5
Downloaded from http://www.everyspec.com

c-
——
Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION430
PIN,SWAGE-LOCKING,
OVAL60°COUNTERSUNKHEAD,
TAPEREII-SECTION
SHANK,MULTIPLELOCKINGGROOVES,
ALUMINUM ALLOY,CORROSIONRESISTANTSTEELAND CARBON STEEL
APPLICABLEDOCUMENT: MIL-P-23469/7
II - MULTIPLE LOCKING GROOVE PINS

.-—..-
..-..-

6 ..-..-
..- ---

.
Shear strength
Material Protective finish (psi) min Class

Aluminum alloy Not specified 26,900 1

6061
Cres #10 Not specified 68,400 2
AISI 304
AISI 305
Carbon steel Not specified 61,600 3
c1035, Clo38,
C1041, C1OB18,
c1OB23
Cadmium plate 68,400 4
Cres
e. ,.
TABLE I. Pin-rivet, qroove, contlquratlon.

D
Nom c
dia

P .218
:808

L ,500

I .625
.768
1,005
.965
.238
.274
,294

r ● 750
1.203
10163
.337
.357

F 1.400 .393

r
1.360 .413
1.597 .454
1.000
,474

430.1
 .
Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10JULY 1979

ItIt-l

L-E-5
----

---

m=
IN(U

---
u au-lo
Onlkn
SE
-0. -
. . . .
--- -N

I
I
(
I
I

------
61,,,,

m
Ill I ----1

. .
--- . .
-NtV

- --
Uncu-1
-- -
Omn
how
. .
.n.o
. ,,
-- --(w

430.2
I
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759
10 JULY 1979

SECTION431

PIN,SWAGE LOCKING,STEEL,
100°CROWN HEAD,TENSION,PULL-TYPE
APPLICABLEDOCUMENT: NAS6935THfW 6942

‘/
100°
W

Tensile strength
Material Protective finish (psi) min

Cadmium plate or 77,900

Alloy steel
AISI-4140 or nickel-cadmium
4340 or 8740 plating
.

TABLE I. Pin-rivet, qroove, configuration part numbers.

i

D Al Basic
Nom Min B part
‘1/
size dia Ref number
I 1

I I
,164 .229 .036 4 NAS6935
.190 ,269 ,045 4 NAS6936
.25U .36i .061 4 NAS6938
.312 .440 ,073 5 NAS6940
,375 .537 .0E?6 5 NAS6942

~/ Number of locking grooves.

 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

-J

mmmmm mcnmmm m
- -- - . ---- - -
. . . . . . . . . . .
mmmmm mmmmrnm

“a L
mcJ

Lb
mm

Lu

m?
A ... ., . . . . . . . . . . . . . . . .
------ ---- I ● O

4 ------ ----- ----.,~ J

1
—

t- 431.2
 Downloaded from http://www.everyspec.com

-----
MIL-STD-1759
10 JULY 1979

SECTION432

PIN,SWAGE LOCKING,
STEEL,
. 100°HEAD,TENSION,STUMP-TYPE
APPLICABLE
DOCUMENT: NAS1486THRU 1492,NAS6925THRU 6932

I
-...

t
Tensile strength
Material Protective finish (psi) min
I
r 1
Alloy steel . Cadmium plate or 77,900
AISI-4140 or nickel-cadmium
4340 or 8740 plating I I
*

L
 Downloaded from http://www.everyspec.com

.-

MIL-STD-1759 .-
10 JULY 1979

TABLE I. Part numbers.

D Nom size.... .164 .190 .250 .312 .375

Al Min dia ....! .263 .316 .344.428.455.508.574,
.629.69:

B Max . . . . . . . . . .055 .071.0s4.048 .110 .109.137.137.16!

m a a N N
N z s w m z ~ m m
NAS Document No w m - m e o v
% % - G - w M a ~ .—

%2
~lu:
●

LQ=
Grip Range L
G “Z5
m~q
n
%-
~mw
iiin Max Lengths ~%z
=U3a

.125 .095 .156 .324 .373 .456 -02 02

.188 .157 .219 .387 .435 .519 .602 .697 -03 03
.250 .220 .281 .449 .498 .581 .664 .760 -04 04
.312 .282 .344 .512 .560 .644 ,727 .822 -05 05
.375 .345 .406 .574 .623 .706 .789 ,885 -06 06

.438 .407 .469 .637 .685 .769 .852 .947 -07 07

.500 .470 .531 .699 .748 .831 .914 1.010 -08 08
.562 .532 .594 .762 .810 ,894 .976 1.072 -09 09
.625 .595 .656 .824 .873 .956 1.039 1.135 -10 10
.688 .657 .719 :887 ●935 1.019 1.101 1.197 -11 11

.750 .720 .781 .949 .998 1.081 1.164 i.260 -12 12

.812 .782 .844 1.012 1.060 1.144 1.226 1.322 -13 13
.875 .845 .906 1.074 1.123 1.206 1.289 1.385 -14 14
.93/3 .907 .969 1.137 1.185 1.269 1.351 1.447 -15 15
1,000 .970 1.031 1.199 1.248 1.331 1.414 1.510 -16 16

1.062 1.032 1.094 1.262 1.310 1.394 1.476 1.572 I -17 17

1.125 1.095 1.156 1.324 1.373 1.456 1.539 1.635 { -18 18
1.188 1.157 1.219 1.387 1.435 1.519 1.602 1.697 -19 19
1.250 1.220 1.281 1.449 1.498 1.581 1.664 1.760 -20 20
1.312 1.282 1.344 1.512 1.560 1.644 1.727 1.822 -21 21

1.375 1..345 1.406 1.574 1.623 1.706 1.789 1.885 -22

IN438 1.407 1.469 1.637 1.685 1.769 1.852 1.947 -23 :;
1.500 1.470 1.531 1.699 1.748 1.831 1.914 2.010 -24 2@
1.562 1.532 1.594 1.762 1.810 1.894 1.976 2.072 -25 ---
1.625 1.595 1.656 1.824 1.873 1.956 2.039 2.135 -26 ---

1.688 1.657 1.719 1.887 1.935 2,019 2.101 2.197 -27 ---
1.750 1.720 1.781 1.949 1.998 2.081 2.164 2.260 -28 ---
1.812 1.782 1.844 2.012 2.060 I 2.]44 2.226 2.322 -29 ---
1,875 1,845 1.906 , 2.074 2.123 ~ 2.206 2.289 2.385 -30 ---
1.938 1.907 1.969 2.137 2.185 2.26!? 2.351 2.447 -31 I ---

2.000 1.970 2.031 2.199 2.248 2.331 2.414 2.510 ~ -32 I

NOTES: 1. For collar selection, see NAS108O.
2. Add “N” dfter basic part null~berfor Nickel-Cadmium plate.
 —
Downloaded from http://www.everyspec.com

. .

..

-----
MIL-STD-1759
10 JULY 1979

SECTION433

PIN,SWAGE LOCKING,
STEEL,
100”SHEARHEAD,STUMP-TYPE
APPLICABLEDOCUMENT: NAS1414THRU 1422

$iil
/
;
+
t
‘+- \\ ‘/

Shear strength
Material Protective finish (psi) min

Alloy steel Cadmium plate or

AISI 4140 or nickel-cadmium 92,400
4340 or 8740 plating

TABLE 1. Pin-rivet, groove, configuration part numbers.

D Al Basic
B
Nom Min part
Max
size dia number

.125 ,180 #037 NAS1414

,156 ,220 .042 NAS1415
,~q) ,263 ,049 NAs1416
,250 .346 .063 NAS1418
.312 .417 .071 NAS1420
,375 ,496 .081 NAS1422
 Downloaded from http://www.everyspec.com
.

MIL”STD”1759
10JULY 1979

TABLE II. NAS1414, 1415, 1416, 1418, 1420 and 1422 Dash numbers.

Grip range L
Grip
G dash
Mln Max .125Dla .156Dia .190Dia .250Dla .312Dia .375Dia “umber

.062 ~/ .062 .201 .236 .261 - 01

.125 .063 .125 .263 .298 .323 .376 *;95 .~38 02
.188 .126 .188 .326 .361 .386 ,439 .458 .501 03
.250 .189 ,250 .388 .423 .448 .501 .520 .563 04
.312 .251 .312 .451 .486 .511 .564 .583 .626 05
,375 ,313 .375 .513 .548 .574 .626 .645 ●688 06
,438 .376 .438 .576 .611 ,637 .689 .708 .751 07
#500 .439 ,500 .638 .673 .699 .751 .770 .813 08
m562 .501 .562 .701 .736 ,762 .814 .833 .876 09
,625 .563 .625 .763 .798 .824 .876 .895 .938 10
t688 .626 ,688 .826 .861 .887 .939 .958 1.001
B750 .689 .750 .888 .923 .949 1.001 1.020 1.063 ;:
,812 .751 .812 .951 .986 1.012 1.064 1.083 1.126 13
,875 .813 .875 1.013 1.048 1.074 1.126 1.145 1.188 14
,938 .876 .938 1.076 1.111 10137 1.189 1.208 1.251 15

t000 .939 1 000

● 1.138 1.173 1.199 1.251 1.270 1.313 16
,062 1.001 1.062 - - 1.261 1.314 1.333 1.376 17
,125 1.063 1.125 - - 1.323 1,376 1.395 1.438
188 1.126 1.188 - - 1.386 1.439 1.458 1.501 ::
250 1.189 1.250 - - 1.448 1.501 1.520 -1.563 20

312 1.251 1.312 - - 1.511 1.564 1.583 1.626

375 1.313 1.375 - - 1.574 1.626 1.645 1.688 :;
438 1.376 1.438 - - 1.637 1.689 1.708 1.751
500 1.439 1.500 - - 1.699 1.751 1.770 1.813 ;:
562 1.501 1.562 - - 1.762 1.814 1.833 1.876 25

625 1.563 1.625 - - 1.824 1.876 1.895 1.938 26

688 1.626 1.688 - - 1.887 1 939
● 1.958 2.001 27
750 1.689 1.750 - - 1.949 2.001 2.020 2.063 28
812 1.751 1.812 - - 2.012 2.064 2.083 2.126 29
875 1.813 1.875 - - 2.074 2.126 2.145 2.188 30

938 1.876 1.938 - - 2.137 2.189 2,208 2.251 31

000 1.939 2.000 - - 2.199 2.251 2,270 2.313 32

I_/ Minimum grip for -01 varies with material to be fastened

together.
NOTES:

1. For collar selection, see NAS108O.

2. Use NAS1080 AG (2219 Al alloy) collars in application up to
450° F. For increase temperature requirementuse NASI080 UK
(A286 Cres) collars.
3. Do not use these parts in Titanium structure.
4. Add “N” after basic part number for Nickel-Cadmium plate.

433.2
 Downloaded from http://www.everyspec.com

.
,

---
MIL-STD-1759
10JULY 1979

SECTION434

PIN,SWAGE LOCKING,STEEL,
PROTRUDINGHEAD,SHEAR,STUMP-TYPE
APPLICABLEDOCUMENT: NAS1424THRU 1432

Shear strength
t$laterial ?rotective finish (psi) min

Alloy steel Cadmium plate or

AISI 4140 or nickel-cadmium 92,400
4340 or 8740 p?ating

TABLE I. Pin-rivet, qroove, configuration part numbers.

D Basic
A B part
Nom
Dia number
size
.

.195 040
NAS1424
●

.125 .181 .028

.249 “~~~ I NAS1425 I
.156 .235 I
.302
.190 .288
●377 :;~j I NAS1428 I
.250 .363
.471 ‘ ‘=
.312 .455
●o8g I NAS1432 I
,375 “&
.Ula I .077 1
I I -1=-’ - J
—
Downloaded from http://www.everyspec.com

MLL-STD-1759
IOJULY 1979

TABLE 11. NAS1424, 1425, 1426, 1428, 1430 and 1432 Dash numbers.
.
G Gri range L
Grip

.062
Min

.020
M&x .125

.201
Dii .156

.236
I
Dia .190 Di

.261
,250 Diz .312 Dia
dash
number

.062
.125 .063 .125 .263 .298 .323 . ;76 .395 :;
.188 .126 .188 .326 .361 .386 .439 .458 03
.250 .189 .250 .388 .423 .448 .501 .520 . 04
.312 .251 .312 .451 .486 .511 .564 .583 05

.375 .313 .375 .513 .548 ,574 .626 .645 06

.438 .376 .438 .576 .611 .637 .689 .708 07
.500 .439 .500 .638 .673 .699 .751 .770 08
.562 .501 .562 .701 .736 .762 .814 .833 09
.625 .563 .625 .763 .798 .824 .876 .895 10

.688 .626 ● 688 .826 .861 .887 .939 .958

.750 .689 .750 .888 .923 .949 1.001 1.020
.812 .751 .812 .951 .986 1.012 1.064 1.083
.875 .813 .875 1.013 1.048 1.074 1.126 1.145
.938 .876 .938 1.076 1.111 1.137 1.189 1.208

1.000 .939 1.000 1.138 1.173 1.199 1.251 1.270

1.062 1.001 1.062 1.261 1.314 1.333
10125 1.063 1.125 1.323 1.376 1.395
1.188 1.126 1.188 1.386 1.439 1.458
1.250 1.189 1.250 .- 1.448 1.501 1.520

1.312 1.251 1.312 - 1.511 1.564 1.583

1.375
1.438
1.313
1.376
1.375
.
1.574
1.637
1.626
1.689
1.645
1.708
$;
23
1.438
1.500 1.439 1.500 1.699 1.751 1.770 24
1.562 1.501 1.562 1.762 1.814 1.833 25

1.625 1.563 1.625 1.824 1.876 1.895 26

1.688 1.626 1.688 1.887 1.939 1.958 27
1.750 1.689 1.750 28
1.812 1.751 1.812 29

J.
1.875 1.813 1.875 . 30

1:938 1.876 1.938 - 31

2.000 1.939 2.000 6 32

NOTES:

1. For collar selection, see NAS 1080.

2. Use NAS108O AG (2219 Al alloy) collars in application Up

to 450° F. For increase temperature requirementsuse

NAS108O UK (A286 Cres) collars.

3. Do not use these parts in Titanium structure.

4. Add “N” after basic part number for Nickel-cadmiumplate.

..434.2
●-
 Downloaded from http://www.everyspec.com

..
MIL-STD-1759
10 JULY 1979

SECTION435

PIN,SWAGE LOCKING,
STEEL,
PROTRUDINGHEAD,TENSION,
STUMP-TYPE
APPLICABLEDOCUMENT: NAS1496THRU 1502

Tensile strength
Material Protective finish (psi) min

Alloy steel
AISI 4140 or
4340 or 8740
Cadmium plate or
nickel-cadmium
plating
I
I
77,900

TABLE I. Pin-rivet, groove, configuration.

Basic
D
Nom A B“ part
Dia number
size I

.164
.270
.255
.317
&kw-
.088 NAS1496
,190 .302 .078
.411 .113 NAS1498
.250 .396 .103
.515 .140 NAS1500
.312 *500 .130
,628 .167 NAS1502
.375 .613 .157
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE II. NAS1496, 1497, 1498, 1500 and 1502 Dash numbers.

Grip range L
Grip
G dash
Mi n Max .164 Dii .190 Dii .2$0 Dli .312 Di .375 Dia number

.062 .031 ● 094 .262 .310 01

.125 .095 .156 .324 .373 .456 .539 .635 02
,188 .157 .219 .387 .435 .519 .602 .697 03
.250 .220 .281 .449 .498 .581 .664 .760 04
.312 .282 ●344 .512 .560 .644 .727 .822 05

.375 .345 .406 ,574 .623 .706 .789 .885

.438 ,407 .469 .637 .685 .769 .852 ●947 ;;
.500 ,470 ,531 .699 .748 .831 .914 1.010 08
.562 .532 .594 .762 .810 .894 .976 1.072 09
.6Z5 ●595 .656 .824 .873 .956 1.039 1.135 10

.688 .657 .719 .887 .935 1.019 1.101 1.197 11

.750 .720 .781 .949 ●998 1.081 1.164 1.260 12
.812 .782 .844 1.012 1.060 1.144 1.226 1.322 13
.875 .845 .906 1.074 1.123 1.206 1.289 1.385 14
.938 .907 .969 1.137 1.185 1.269 1.351 i.447 15

1.000 .970 1.031 1.199 1.248 1.331 1.414 1.510 16

1.062 1.032 1 094
● 1.262 1.310 1.394 1.476 1.572 17
1.125 1.095 1.156 1.324 1.373 1.456 1.539 1.635 18
1.188 1.157 1.219 1.387 1.435 1.519 1.602 1.697
1.250 1.220 1.281 1.449 1.498 1.581 1.664 1.760

1.312 1.282 1.344 1.512 1.560 1.644 1.727 1.822 21

1.375 1.345 1.406 1.574 1.623 1.706 1.789 1.885 22
1.438 1.407 1.469 1.637 1.685 1.769 1.852 1.947 23
1.500 1.470 1.531 1.699 1.748 1.831 1.914 2.010 24
1.562 1.532 1.594 1.762 1.810 1.894 1.976 2.072 25

1.625 1.595 1.656 1.824 1.873 1.956 2.039 2.135 26

1 688
● 1.657 1.719 1.887 1.935 2.019 2.101 2.197 27
1.750 1.720 1.781 1.949 1.998 2.081 2.164 2.260 28

NOTES: 1. For collar selection, see NAS108O.

2. Add “N” after basic part number for Nickel-Cadmium plate.

.435.?
 Downloaded from http://www.everyspec.com

.:.

-. -
MIL-STD-1759
10 JULY 1979

SECTION
436

PIN,SWAGE LOCKING,
STEEL,
100°HEAD [MS20426],
TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS1475THRUl~2

I
%..
w. L-s

I A,
100° Bill
::-- ..”---

L
uJ
b I
l—---- L I

Tensile strength
Material Protective finish (psi) min

Alloy steel Cadmium plate or 77,900

AISI-4140 or nickel-cadmium
4340 or S740 plating

TABLE I. Pin-rivet, qroove, confi9uration9

Al “ B Basic
D
Nom Min Max u part
size dia u number

.164 ,263 .055 4 NAS1475

.190 .316 ,071 4 NAS1476
.250 .428 .098 4 NAS1478

l_/ Number of locking grooves.

 Downloaded from http://www.everyspec.com
“.

-—
MIL-STD-1759
10 JULY 1979

TABLE II. NAS1475, 1476 and 1478 Dash numbers.

Grip range .164 Dia .190 & .203 Dia .250 & .266 Dia
Grip
G dash
Min Max L P L P L P number

.125 .095 .156 .313 1.50 .358 1.44 .437 1.88

.188 .157 .219 .376 1.62 .421 1.56 .499 2.00 :;
.250 .220 ,281 .438 1.75 .483 1.69 .562 2.12 04
,312 .282 ● 344 .501 1*88 .546 1.81 .624 2.25 05
.375 .345 .406 .563 2.00 .608 1.94 ,687 2.38 06

.438 .407 .469 .626 2.12 .671 2.06 .749 2.50 07

● 500 .470 .531 .688 2.25 .733 2.19 .812 2.62
.562 .532 .594 .751 2.38 ,796 2.31 .874 2.75 ::
.625 .595 .656 .813 1.88 .858 2.44 .937 2.88 10
.688 .657 .719 .876 1.94 .921 2.56 .999 3.00 11

.750 .720 .781 .938 2.00 .983 2.69 1.062 3.12 12

.812 .782 .844 1.001 2.06 1.046 2.81 1.124 3.25 13
.875 .845 .906 1.063 2.12 1.108 2.94 1.187 3.25 14
.938 .907 ,969 1.126 2.19 1.171 3.06 1.249 3.25 15
1.000 .970 1.031 1.188 2.25 1.233 3.19 1.312 3.25 16

1.062 1.032 1.094 1.251 2:31 1.296 3.19 1.374 3,25 17

1.125 1.095 1.156 1.313 2.38 1.358 3.19 1.437 3.25 18
1.188 1.157 1.219 1.376 2.44 1.421 3.19 1.499 3,25 19
1.250 1.220 1.281 1,438 2.50 1.483 3.19 1.562 3.25
1.312 . 1.282 1.344 1.501 2.56 1.546 3.19 1.624 3.25 :!

1*375 1*345 1.406 1.563 2.62 1.608 3.19 1.687 3,25

1.438 1.407 1.469 - - 1.671 3.19 1.749 3.25 E
1.500 1.470 1.531 - - 1.733 3.19 1.812 3.25
1.562 1.532 1.594 - - 1.796 3.19 1.874 3.25 ::
1.625 1.595 1.656 - - 1.858 3.19 1.937 3.25 26

1.688 1.657 1.719 - - 1.921 3.19 1.999 3.31 27

1.750 1.720 1.781 - - 1.983 3.19 2.062 3.38
1.8.12 1.782 1.844 - - 2.046 3.19 2.124 3.44 ;:
1.875 1.845 1.906 - - 2.108 3.19 2.187 3.50 30
1.938 1.907 1.969 - - 2.171 3.19 2.249 3.56 31

2.000 1.970 2.031 - - 2.233 3.19 2.312 3.62 32

NOTES: 1. For collar selection, see NAS108O.

2. Add “N” after basic part number for Nickel-Cadmium plate.

436.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION437

PIN,SWAGE LOCKING,
STEEL,
100°HEAD[MS24694],
TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS14S6THRU 1462

(’Al
loo”~
\
r Al I = %..~.x--

= Illllnl
1 % --------

VI
+—-L+

6 r

Tensile strength
Material Protective finish (psi) min
I
Alloy steel Cadmium plate or 77,900
AISI-4140 or nickel-cadmium
4340 or 8740 plating

TABLE 1. Pin-rivet, groove, confi~uration.

D ‘1 B Basic
Nom min max u part
size dia Y number

.190 ,344 .084 4 NAS1456

.250 ,455 .110 4 NAS1458
.312 ,574 *137 5 NAS1460
.375 .693 .165 5 NAS1462

~/ Number of locking grooves.

 Downloaded from http://www.everyspec.com
.
.

-.

MIL-STD-1759
10 JULY 1979

.
L
0

4
L

L>
Ou
k<

.*

43 .2
3
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION438

PIN,
SWAGELOCKING,
STEEL,
100°SHEAR HEAD,PULL-TYPE
APPLICABLEDOCUMENT: NAS1436THRU1U1

Shear strength
I Material
I
I
Protective finish
I
(psi) min

Alloy steel Cadmium plate or

AISI 4140ar nickel-cadmium 92,400
4340 or 8740 plating

TABLE 1. Pin-rivet, groove, configuration.

‘1 B Basic
D Min Max part
Nom dia number
size

.190 .263 ,049 NAS1436

.250 .346 .063 NAS1438
.312 ,417 ,071 NAS1440
.375 ,496 .081 NAS1442
—
Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

n.

- ------ ---- -.--- wLwwcwml Cu

n
.-
0
N
m
m.

.-
—

. . . . . . . . . . . . .
~Nfw(v wNNNmJ fmfnmlmm” mmrm
“ ‘ - mm”””””
“ rnl-lmtmm ““””””
mmmmm m“

.=
n
o
m

.
“w
ul
- d----- ---- ----- N
L
m

----- ----- --- -., l%

(n
u
+
c
=

t- 438.2-
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION439

PIN,SWAGE LOCKING,
STEEL,
PROTRUDINGHEAD,SHEAR,PULL-TYPE
APPLICABLEDOCUMENT: NAS1448THRU 1452

Shear strength
Material Protective finish
(psi) min

Alloy steel Cadmium plate or

AISI 4140 or nickel-cadmium 92,400
4340 or 8740 plating

TABLE 1. Pin-rivet, qroove, configuration.

o A B Basic
Nom dia Max - part
size number
.

.302 .063
.190 NAS1446
.288 m
,377 .081
I 0250 NAS1448
,363 ,074.
.471 .100
,094 NAS1450
J!&
.565 .120
NAS1452
I ,375
,549 .113

439.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979 -

1
!

. . . . . . . . . . . . -----
. . . . . . . . . . . . . . . . . . . w.
-.
d---- --- ---m-m
I
i

c
.-
S

I
. . . . . . . . . . . . . . . . . . . . . . . . . ,, .,. . .
------ ----- ---- -w
I

439.2
t-
 Downloaded from http://www.everyspec.com

-.

MIL-STD-1759
10JULY 1979

SECTION440

PIN,SWAGE LOCKING,
STEEL,
PROTRUDINGHEAD,TENSION,
PULL-TYPE
APPLICABLEDOCUMENT: NAS1465THRU 1472
y G-1
B

‘1 F.

Tensile strength
--- - Material Protective finish (psi) min

Alloy steel Cadmium plate or 77,900

I
AISI-4140 or nickel-cadmium
4340 or 8740 Dlatinq

TABLE 1. Pin-rivet, qroove, configuration.

D A Basic
Nom dia part
size number

.282 .095 4
NAS1465
.164
.258 .085
.327 .111 ~
,190 ,297 NAS1466
.099
.430 147 4
.250 NAS1468
.390 :128
.535 ,184 s
.312 NAS1470
.485 .158

m
I

NAS1472
L. w

~/ Number of locking grooves.

440.1
I b“)
/).
 Downloaded from http://www.everyspec.com

MIL-STD-1759
IOJULY 1979

.
2
m
n
N
h
u

r-l

. .
-N
 Downloaded from http://www.everyspec.com

----- MIL-STD-1759
10 JULY 1979

SECTION441

PIN,SWAGE-LOCXING,
TRUSS HEAD,STRAIGHTSHANK,
SIXLOCKINGGROOVESAND MULTIPLELOCKINGGROOVES.
ALUMINUM ALLOY,CORROSIONRESISTANTSTEELAND CARBON STEEL
APPLICABLEDOCUMENT: MIL-P-234B9/5

Shear strength
Material Protective finish Class
(psi) min

Aluminum
alloy Not specified 26,900 1
6067
Cres #10
AIS1 304 Not specified 68,400 2
AISI 305
Carbon steel
C1035, C1038,
C1041, C1OBI8, Not specified 61,600 3
C1OB23

441.1
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10JULY 1979

TYPE I - SIX LOCKING GROOVE PINS

TABLE 1. Pin-rivet, groove, configuration.

Jd=l=l-
D
Nom
dia 1
I 1 1
.188
.469 I .078 I .078 I
.406 ●088 ,088
594
●
.108 .103
.250 .121 .115
.531
.797 .143 .127
,312

.375
%?t%-HH

441.2
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759
10 JULY 1979

l“’’’’”

..

m
I

--
/

1------ --

... ...
----..
I

I
1
--
-r

I
 —
Downloaded from http://www.everyspec.com

-.

MIL-STD-1759
10 JULY 1979

TYPE 11 - MULTIPLE LOCKING GROOVE PINS.

*)(

i 1

=..-..-
-----

TABLE I. Pin-rivet, groove, configuration.

4

D
Nom A c
dia Dia
,

1.138 .225
500 .250
1.075
●

1.343 .288
.625 1.280 .313
1.608 .340
.750 1.545 .375
1.915 .395
.875 .438
1.790
2.180 .452
1.000 .500
2.055

441.4
WA
 Downloaded from http://www.everyspec.com

.-

MIL-STD-1759
10 JULY 1979

111 1811

1111111 1 Ill Ill

-N- N-nJ A
N tncoo mmco o

r . ..0 . . .

x ,... . . .
----

000 000 gcJ

Obno $nObn
m-c ON
. . .
NtiI%
. . . . . —.,. . . . . . . . . .
--- mm -- --NO -- S--*6J

---- ---- -- - - -- ----- -

Lnc.n Oulc
Ofvul
mo
ho
Obno
Otio mom
mm-
z
c
Omo
m-o
glg z
.,..
cNun-
. . . . . . . . . . .,,. . . o.
--- -ru --- n --- w

111111 11

1- 148 14811

. . . . ,..,

mmm mmm mmm mm

a-a -a-
-m@m-
Z2 mm?-)
ma- mma mm
f-l@Q
. . . . . . . .
Wwm -w@m-
..,, . . . ,
--- N(WN Nm --- CUNN mlm

dl
u
=1

.— .- t . . . . ..,. ml x
.,.. . . . .
---- ---- ----
01
I 01
I nt
W,

I .- 1
--- ---- - --- --- --
i+ Lncu, Cmo Lncm otna Ino
1 I NLnl= cNm K!= (NLn- oNbn -0
,.. ,.. . .
--- -w

441.!5
Downloaded from http://www.everyspec.com
,

●✎✎
✎
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

442
SECTION

WASHER FACE,BRAZIERHEAD,STRAIGHT
PIN,SWAGE-LOCXING,
SHANK,SIXLOCXINGGROOVES,CORROSIONRESISTANTSTEEL
APPLICABLEDOCUMENT: MIL-P-23469/3
TYPE I - SIX LOCKING GROOVE PTNS

I m
x

r
A

I
L “

Shear strength
Material Protective finish Class
(psi) min
1

Cres #10 Not specified 68,400 2

AISI 304
AISI 305
TABLE I. Pin-rivet, aroove, c0nfi9uratiOno

D
Nom A c
dia Dia

.656 .181
.312
.594 .201
.787 .223
.375 .248
,713

TABLE II. M23fU /3 Dash numbers.

.312 Diameter Dash no. .375 Diameter ! Oash no.
Grip range T= GrlD ranoe XIY z ~c,:gs2
MIn Max
lx y z
Class 2 Min I Max i

.125 I ,375 I .125 .570 -21004 .125 .375 I .125 ~ .658 2.25 ! -21204
.695 -21006 ,250 .5(20: .250 .783 2.:8 I -21206
,250 i ,500 [ .250
,625 ~ .375 -2100s .375 .625 ,:75 I ,909 2.50 / -21208
.375 ~
I
coo Ii .750 : .500 ,gq~ ~ 2.34 -21010 .500
,625 .875 ~ .625 ! 1.070 : 2.47 -Z1012 .6?5
.750 1.000 ‘ .750 1.]95 ; 2,59 -21014 .759
I , t I I

.875 ].~25 .875 ! 1.:20 i 2.72 -21016 .875

~.000 I 1.250 1!000 ~ 1,445 : 2,(34 -210?s 1.!300

442.1
 Downloaded from http://www.everyspec.com
.

-.

--

-+

b
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION501

P!N,CRIMP,100°CROWN SliEAR/TENSION
HEAD
APPLICABLEDOCUMENT: NAS4466

—G---T

‘r I

fi
100° ‘1 —

G
—1. -1
shear strength Tensile strength
Material Protective finish
(psi) min (psi) min

Alloy steel Cadmium plate or 108,000 93,700

AISI 4340 nickel-cadmium
or 8740 plating

TABLE 1. Pin-rivet, threaded, configuration part numbers.

D Al Basic
Nom Mln B J part
size dia Ref Thread number

.1640-32
.164 .229 .036 NAS4466( )05
UNJC-3A
.1900-32
.190 .269 .045 NAS4466( )06
UNJF-3A
.2500-28
.250 .361 .061 NAS4466( )08
+ UNJF-3A
7]25-7~
.312 .440 1.073 NASG466( )10
UNJF-3A

I .086 UNLIF-3A
.3750-24
.375 .527 NAS4466( )12
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

. TABLE II. NAS4466 Dash numbers.

Grip range L
Grip
G dash
.164 Dia .190 Dia .250 Dia .312 Dia .375 Dia number

.125 .063 .125 .382 .410 .473 -02

●188 .126 .188 .445 .473 .536 .599 .659 -03
.250 .189 .250 ,507 .535 .598 .661 .721 -04
.312 .251 .312 ,570 .598 .661 .724 .784 -05
.375 .313 ,375 ,632 ,660 .723 .786 .846 -06

.438 .376 .438 .695 .723 .786 .849 *909 -07

.500 .439 .500 ,757 .785 .848 .911 .971 -08
.562 .501 .562 .820 .848 .911 *974 1.034 -09
.625 .563 .625 .882 .910 ,973 1.036 1.096 -10
●688 .626 .688 .973 1.036 1.099 1.159 -11

.750 .689 ,750 1.035 1.098 1.161 1.221 -12

.812 .751 .812 1.161 1.224 1.284 -13
.875 .813 .875 1.223 1.286 1.346 -14
.938 .876 .938 1.286 1.349 1 409
● -15
1.000 .939 1.000 1.348 1.411 1.471 -16

1.062 1.001 1.062 1.474 1.534 -17

1.125 1.063 1.125 1.536 1.596 -18
1.188 1.126 1.188 1.599 1.659 -19
1.250 1.189 1.250 1.661 1.721 -20
1.312 1.251 1.312 1.784 -21

1.375 1.313 1.375 1.846 -22

1.438 1.376 1.438 1.909 -23
1.500 1.439 1 500
● 1.971 -24

NOTE : For crimp nut selection, see NAS4455.

 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION502

100°FLUSH SHEAR HEAD

PIN,CN!’IP,
APPLICABLEDOCUMENT: NAS44’52

B+D

‘A
/#-, (’
@-’ /-’
\ L:J ,
\. /
100° Al —

Shear strength
Ilaterial Protective finish
(psi) min
w

Alloy AIS14340
steel or 8740
Cadmium plate
I 108,000

Nickel-cadmium
H-n 156,000
plating
Titanium
alloy None 95,000
6AL-4V

TABLE I. Pin-rivet, threaded, configuration part numbers.

D Al Basic
Nom Mln B J part
size dia Max Thread number

.1640-32
.164 .220 .040 NAS4452( )05
UNJC-3A
.1900-32
,190 .263 ,049 NAS4452( )06
UNJF-3A
.2500-28
,250 .346 .063 NAS4452( )08
UNJF-3A
.3125-24
.312 .456 .077 NAS4452( )~o
UNJF-3A
.3750-24
.375 .517 .091 UNJF-3A
NAS4452( )12

.Iz-”’
 Downloaded from http://www.everyspec.com

.-

MIL-STD-1759
10 JULY 1979

TABLE II. NAS4452 Dash numbers.

L
G Grip
dash
Min Max .164 Di( .190 Di .250 Di( .312 Dit .375 Di( number
.
.125 .063 .125 .382 .410 .473 -02
.188 .126 *188 .445 .473 .536 .599 .659 -03
.250 .189 .250 .507 ●535 .598 .661 ,721 -04 .
.312 .251 .312 .570 .598 .661 .724 .784 -05
.375 .313 .375 .632 .660 .723 .786 .846 -06

.438 .376 ,438 .695 .723 .786 .849 .909 -07

.500 .439 ,500 .757 .785 .848 .911 ●971 -08
.562 .501 .562 .820 .848 ●911 .974 1.034 -09
.625 .563 .625 .882 .910 .973 1.036 1.096 -lo
.688 .626 .688 Ieogg -
.973 1.036 1.159 -11

.750 .689 .750 1.035 1.098 1.161 1.221 -12

.812 .751 .812 1.161 1.224 1.284 -13
.875 .813 .875 1.223 1.286 1.346 -la
.938 .876 ,938 1.286 1.349 1.409 -15
.939 1*000 1*348 laql 1.471 -16

1.062 1.001 1.062 1.474 1.534 -17

1.125 1.063 1.125 1.536 1,596 -18
1 188
● 1.126 1.188 1.599 1.659 -19
1.250 1.189 1.250 1.661 1.721 -20
1.312 1.251 1.312 1.784 -21

1.375 1.313 1*375 1.846 -22

1:438 1.376 1.438 1.909 -23
1.500 I 1.439 1 500
●
I 1.971 -24

NOTE : For crimp nut selection, see NAS4445.

 Downloaded from http://www.everyspec.com

----- MIL-STD-1759
10 JULY 1979

SECTION
503

PIN,CRIMP,PROTRUDINGSHEAR HENI
APPLICABLEDOCUMENT: NAS4450

2 1 1
Shear strength
Material Protective finish (psi) min
f I
I
1 I 1
Cadmium plate or
AISI 4340 nickel-cadmium 108,000
or 874C
AHOY plating
steel ‘
Nickel-cadmium 156,000
H-II plating

Titanium alloyl None 95,000

6AL-4V

TABLE I. Pin-rivet, threaded, cOnfi9uratjOn Part numberso

D Basic
J.

part

I
Nom A.B
dia Dia Thread number
1

.164
.257 I ,047
,039
.1640-32
UNJC-3A
NAS4450( )05

5=
.245
.312 .050 ,1900-32
I .190 NAS4450( )06
.298 .042 UNJF-3A
.413 .069 .2500-28
I ,250
.398 .061 UNJF-3A
NAs4450( )08

“t-
I
.312
.503
.483
.0/8
.070 ‘UNJF-3A
NAS4450( )10

*.583 .088 .3750-24

NASJ450( )12
I .375
.563 1.080 UNJF-3A

503.1
 Downloaded from http://www.everyspec.com

.:

MIL-STD-1759
10JULY 1979

TABLE 11. NAS4450 Dash numbers.

I
Grip range L
Grip
G dash
Min Max .164 Dia .190 Dia .250 Dia .312 Dia .375 Dia . number

.062 - .062 .320 .348 .411 01

.125 .063 .125 .382 .410 .473 .;36 .;96 02
.188 .126 .188 .445 .473 .536 .599 .659 03
.250 .189 .250 ●507 .535 .598 .661 ,721 04
.312 .251 .312 .570 .598 .661 .724 .784 05

.375 .313 .375 .632 .660 .723 .786 .846 06

.438 .376 .438 .695 .723 .786 .849 .909 07
.500 ,439 .500 .757 .785 .848 .911 .971 08
.562 .501 .562 .820 .848 .911 .974 1.034 09
.625 .563 .625 .882 .910 .973 1.036 1.096 10

.688 .626 .688 - .973 1.036 1.099 1.159 11 ‘

.750 .689 .750 - 1.035 1.098 1.161 1.221 12
.812 .751 .812 - - 1.161 1.224 1.284 13
.875 .813 .875 - - 1.223 1.286 1.346 14
.938 .876 .938 - - 1.286 1.349 1.409 15

1.000 .939 1.000 - - 1.348 1.411 1.471 16

1.062 1.001 1.062 - - - 1.474 1.554 17
1.125 1.063 1.125 - - 1.536 1.596 18
1 188
● 1.126 1.188 - - 1.599 1.659 19
1.250 1.189 1.250 - - “- 1.661 1.721 20

1.312 1.251 1.312 - - - - 1.784 21

1.375 1.313 1.375 - - - - 1.846 22
1.438 1.376 1.438 - - - - 1.909 23
1.500 1.439 1.500 - - - - 1.971 24

NOTE : For crimp nut selection, see NAS4445.

503.2
d
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION504

PIN,CRIMP,PFIOTRUDING
TENSIONHEMI
APPLICABLEDOCUMENT: NAS4458

—-G——

fJ

Tension strength
Material Protective finish (psi) min

Alloy steel Cadmium plate or

AISI 4340 or nickel-cadmium 93,700
8740 plating

TABLE I. pin-rivet, threadedt COnfiWation part numbers.

D
Nom
dia
T A
Dia

.257 !
B

.077-
J
Thread

.1640-32
Basic
part
number

NAS4458( )05
.164 ,070 UNJC-3A
.245
.312 0086. .1900-32
.190 NAS4458( )06
.298 .079 UNJF-3A
,413 .111 .2500-28
.250 NAS4458( )o~
.398 ,104 UNJF-3A
,503 ,137 .3125-24
.312 NAS4458( )lo
.(183 .130 UNJF-3A
.5ii3I .164 .3750-24
.375 NAS4458( )12
.563 I .157 UNJF-3A

504.1
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

TABLE II. NAS4458 Dash numbers.

1
Grip range L Grip
G dash
.164 Dia ● 190 Dia .250 Dia .312 Dia .375 Di{ number
E
.062
.125
●188
.250
.312
.063
.126
.189
.251
.062
.125
.188
.250
.312
.320
.382
.445
.507
.570
.348
.410
.473
.535
.598
.411
.473
.536
.598
.661
.536
.599
.661
.724
.596
.659
.721
.784
101
02
03
04
05

,375 .313 .375 .632 .660 .723 .786 .846 06

.438 .376 .438 .695 .723 .786 .849 .909 07
.500 .439 .500 .757 .785 .848 .911 .971 08 I
.562 .501 .562 .820 .848 .911 .974 1.034 09
.625 ,563 ,625 .882 .910 .973 1.036 1.096 10

●688 .626 ●688 .973 1.036 1.099 1.159 11

.750 .689 .750 1.035 1.098 1.161 1.221 12
.812 .751 .812 1.161 1.224 1.284 13
,875 .813 .875 1.223 1.286 1.346 14
.938 .876 .938 1.286 1.349 1.409 15

1 000
● .939 1.000 1.348 1.411 1.471 16
1.062 1.001 1.062 1.474 1.534 17
1.125 1.063 1.125 1.536 1.596 18
1.188 1.126 1.188 1.599 1.659 19
1.250 1.189 1.250 1.661 1.721 20

1.312 1.215 1.312 1.784 21

1.375 1.313 1.375 1.846 22
1.438 1.376 1.438 1.909 23
1.500 1.439 1,500 1.971 24 “

NOTE : For crimp nut selection, see NAS4445.

504.2
 Downloaded from http://www.everyspec.com

.-

----
MIL-STD-1759
10 JULY 1979

SECTION505

Plhl-RIVET,
--- THREADEILBUTTONHEAD,STRAIGHT
SHAM(
/lO,/l4
APPLICABLEDOCUMENT:MIL-P-23470/l./5,

~D

ALH L THREAD

Material Protective finish Shear strength

Footnotes Part Numbers
(psi) min

M2~470/14 Aluminum alloy Anodic coat 24,950

~/
+ dash nos. 6061-T6

Carbon steel Zinc plate 68,400

~1 M23470/5
+ dash nos. ASTM A546

M23470/10 Cres 304 or Passivate 68,400

~/
+ dash nos. 304L or 305
or 316 or 316L

M23470/1 Cres, class 304 Passivate 68,400

&/
or 304L or
305 or 316 or
316L

1/ Threads shall be class 3A (UNF-3.A)of Handbook H-28, per MIL-S-8879.

2_/,~/, 4_/Threads shall be class 2A (UNF-2A) of Handbook H-28, per lfIL-S-887Q.

--
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

TABLE I. Part numbers (M23470/14,/5,/10).

D Nom .... .188 .250 .312 .375

A Min .... .343 .469 .531 .656

Max .... ,374 “,500 .563 ,687

H Min .... .094 .125 .156 .188

Max .... .114 .145 .176 .208

Grip range l_/, ~/, ‘ y, L/, L l/s y, ‘ y y

L
Min Max or ~/ or ~/ or ~/ or ~1

,062 .188 .531 -1 .594 -33 .656 -65 .719 -97

.188 .312 .656 -2 .719 -34 .781 -66 .844 -98
.312 .438 .781 -3 .844 -35 .906 -67 .969 -99
,438 .562 .906 -4 .969 -36 1.031 -68 1.094 -100
.562 ●688 1.031 -5 1.094 -37 1.156 -69 1,219 -101

.688 .812 1.156 -6 1.219 -38 1.281 -70 1.344 -102

.812 .938 1.281 -7 1.344 -39 1.406 -71 1.469 -103
.938 1.062 1.406 -8 1.469 -40 1.531 -72 1.594 -104
1.062 1.188 1.531 -9 1.594 -41 1.656 -73 1.719 -105
1.188 1.312 1.656 -lo 1.719 -42 1.781 -74 1.844 -106

1.312 1.438 1.781 -11 1.844 -43 1.906 -75 1.969 - i07
1.438 1.562 1.906 -12 1.969 -44 2.031 -76 2 094
● -108
1.562 1 688
● 2.031 -13 2.094 -45 2.156 -77 ‘2.219 -109
1 688
● 1.812 2.156 -14 2.219 -46 2.281 -78 2.344 -110
1.812 1.938 2.281 -15 2.344 -47 2.406 -79 2.469 -111

1.938 2,062 2.406 -16 2.469 -48 2.531 -80 2,594 -112
2.062 2.188 2.531 -17 2 594
● -49 2.656 -81 2.719 -113
2.188 2.312 2.656 -18 2.719 -50 2.781 -82 2.844 -114
2.312 2.438 2.781 -19 2,844 -51 2.906 -83 2.969 -115
2.438 2,562 2,906 -20 2.969 -52 3.031 -84 3.094 -116

2.562 2 688
● 3.031 -21 3.094 -53 3.156 -85 3.219 -117
2.688 2.812 3.156 -22 3.219 -54 3.281 -86 3.344 -118
2.812 2.938 3.281 -23 3.344 -55 3.406 -87 3,469 -119
2.938 3.062 3.406 -24 3,469 -56 3.531 -88 3.594 -120
3.062 3.188 3.531 -25 3.594 -57 3.656 -89 3.719 -121

3.188 3.312 3.656 -26 3.719 -58 3.781 -90 3.844 -122
3,312 3.438 3.781 -27 3.844 -59 3.906 -91 3,969 -123
3.438 3.562 3.906 -28 3.969 -60 4.031 -92 4.094 -124
3.562 3.688 4.031 -29 4.094 -61 4.156 -93 4.219 -125
3.688 3.812 4.156 -30 4.219 -62 4.281 -94 4,344 -126

3.812 3.938 4.281 -31 4.344 -63 4.406 -95 4,469 -127
3.938 4.062 4.406 -32 4.465 -64 4.531 -96 4,594 -128

~/, ~/, ~/ (see page 505.1)

505.2
 Downloaded from http://www.everyspec.com

.-

MIL-STD-1759
10JULY 1979

TABLE 1. Part Numbers (M23470/14,/5,/10), - Continued

D Nom,,.. .438 .500 ! .625 .750

Mint... .719 .828 1,063 1.125

A
Max .... .750 .859 1.094 1.156

H Min .... .219 .250 .312 .375

Max,... .239 .270 .332 .395

Grip range y, gL ~ y, 21, ~ y9 gL ~ l_L g/

–
L
Min Max or ~/ or ~/ or ~1 or ~1

.062 .188 .781 -129 .844 -161 .906 -193 1.031 -225
.188 .312 .906 -130 .969 -162 1.031 -194 1.156 -226
.312 .438 1.031 -131 1 094
● -163 1.156 -195 1.281 -227
.438 .562 1.156 -132 1.219 -164 1.281 -196 1.406 -228
.562 .688 1.281 “133 1.344 -165 1.406 -197 1.531 -229

.688 .812 1.406 -134 1.469 -166 1.531 -198 1.656 -230
.812 .938 1.531 -135 1.594 -167 1.656 -199 1.781 -231
.938 1.062 1.656 -136 1.719 -168 1.781 -200 1.906 .232
1.062 1.188 1.781 -137 1.844 -169 1.906 -201 2.031 -233
1.188 1.312 1.906 -138 1.969 -170 2.031 -202 2.156 -234

1.312 1.438 2.031 -139 2.094 -171 2,156 -203 2.281 -235
1.438 1,562 2.156 -140 2.219 -172 2.281 -204 2.406 -236
1.562 1.688 2.281 -141 2.344 -173 2.406 -205 2.531 -237
1.688 1.812 2.406 -]42 2.469 .174 2.531 -206 2.656 -238
1.812 1.938 2.531 -143 2.594 -175 2.656 -207 2.781 -239

1.938 2.062 2.656 -144 2.719 -176 2.781 -208 2.906 -240
2.062 2.188 2.781 -145 2.844 -177 2,906 -209 3.031 -241
2.188 2.312 2.906 -146 2.969 -178 3.031 -210 3.156 -242
2.312 2.438 3,031 -147 3,094 -179 3.156 -211 3.281 -243
2.438 2.562 3.156. -148 3.219 -180 3.281 -212 3,406 -244

2.562 2.688 3,281 -149 3*344 -181 3.406 -213 3.531 -245
2.688 2.812 3.406 -150 3.469 -182 3.531 -214 3.656 -246
2.812 2.938 3.531 -151 3.594 -183 3,656 -215 3.781 -247
2.938 3.062 3.656 -152 3.719 -184 3.781 -216 3.906 -248
3.062 3.188 3.781 “153 3.844 -185 3.906 -217 4.031 -249

3.188 3.312 3.906 -154 3.969 -186 4.031 -218 4,156 -250
3.312 3.438 4.031 -155 4.094 -187 4.156 -219 4.281 -251
3.438 3.562 4.156 -156 4.219 -188 4.281 -220 4.406 -252
3,562 3.688 4.281 -157 4.344 -189 4.406 -221 4.531 -253
3.688 3.812 4.406 -158 4.469 -190 4.531 -222 4.656 -254

3.812 3,938 4,531 -159 4.594 .VJ1 4.656 -223 4.781 -255
3.938 4.062 4,656 -160 4.719 .192 4.781 .Zzfl 4,906 -256
 Downloaded from http://www.everyspec.com

MIL-STD-1759
.+
10 JULY 1979

TABLE II. Part numbers (M23470/1).

D Nom.., .250 ,312 ,375 .438 .500

A Min... .565 .688 .813 .938 1.063 “

Max... .594 .719 .844 .969 1.094

H Min.., .125 .156 .188 .219 .250

Max.., .145 .176 ,208 .239 .270

Grip range
L L L L L ~/
Min Max

.062 ,188 .594 -33 .656 -65 .719 -97 ,781 -129 .844 -161
.188 .312 .719 -34 .781 -66 .844 -98 .906 -130 .969 -162
.312 .438 .844 -35 .906 -67 .969 -99 1.031 -131 1.094 -163
.438 .562 .969 -36 1.031 -68 1.094 -100 1.156 -132 1.219 -164
.562 ●688 1 094
● -37 1.156 -69 1.219 -101 1.281 -133 1.344 -165

.688 .812 1.219 -38 1.281 -70 1.344 -102 1.406 -134 1.469 -166
.812 .938 1.344 -39 1.406 -71 1.469 -103 1.5:1 -135 1.594 -167
.938 1.062 1.469 -40 1.531 -72 1.594 -104 1.656 -136 1.719 -168
1.062 1.188 1.594 -41 -73 1.781 -137 1,844 -169
1.656 1.719 -105
10188 1.312 1.719 -42 1.781 -74 1.844 -106 1.906 -138 1.969 -170

1.312 1.438 1.844 -43 1.906 -75 2.!)31 -139 2.094 -171
1.969 -107
1.438 1.562 1.969 -44 2.031 -76 2.094 -108 2.156 -140 2.219 -172
1.562 1.688 2.094 -45 2.156 -77 2.219 -109 2.281 -141 2.344 -173
1.688 1.812 2.219 -46 2.281 -78 2.344 -110 2.406 -142 2.469 -~7L?
1.812 1.938 2.344 -47 2.406 -79 2.469 -111 2.531 -143 2.594 -175

1.938 2.062 2.469 -48 2.531 -80 2.594 -112 2.656 -144 2.719 -176
2.062 -49 2.781 -14~ 2.844 -177
2.188 2.594 2.656 -81 2.719 -113
2.188 2.312 2.719 -50 2.781 -82 2.844 -114 2.906 -146 2.969 -178
2.312 2.438 2.844 -51 2.906 -83 2.969 -115 3,031 -147 3.094 -179
2.438 2.562 2.969 -52 3.031 -84 3.094 -116 3.156 -148 3.219 -180

2.562 2,688 3.094 -53 3.156 -85 3.219 -117 3.281 -149 3.344 -181
2.688 2.812 3.219 -54 3,281 -86 3.344 -118 3.406 -150 3.469 -182
2.812 2.938 3.344 -55 3.406 -87 3.469 -119 3.531 -151” 3.594 -183
2.938 3.062 3.469 -56 3.531 -88 3.594 -120 3.656 -152 3.719 -184
3.062 3.188 3.594 -57 3.656 -89 3.719 -121 3.781 -153 3.844 -185

3.188 3.312 3.719 -58 3.781 -90 3.844 -122 3.906 -154 3.969 -186
3.312 3.438 3.844 -59 3.906 “91 3.969 -123 4.031 -~55 4,094 -187
3.438 3.562 3.969 -60 4.031 -92 4.094 -124 4.156 -156 4.219 -188
3,562 3.688 4.094 -61 4,156 -93 4.219 -125 4.281 -157 4.344 -189
3.688 3.812 4.219 -62 4.281 -94 4.344 -126 4.406 -158 4.469 -190
I
3.812 3.938 4,344 -63 4.406 -95 4,469 -127 4,531 -159 4.594 -191
3.938 4.062 4.469 -64 4.531 -96 4.594 -128 4,656 -160 4.71? .192

~/ (see page 505.1)

505*4
...
/ \
 —
Downloaded from http://www.everyspec.com

...
MIL-STD-1759
10 JULY 1979

SECTION506

PIN-RIVET,
THREADED,BUTTON HEAD,
TAPEFIEil
SHANK
APPLICABLE DOCUMENT: MIL-P-23470/2,/6,
/15

THREAD D
\ 1

GRIP I
L
1- ~ RAA
—

Material Protective finish Shear strength

Footnotes Part Numbers
(psi) min

Aluminum alloy Anodic coating 24,950

M23470/~5
+ dash no. 6061-16

Zinc p ate 70,500

M23470/6 Carbon steel
+ dash no. ASTM A546

Cres 304 or Passivate 68,400

M23470/2
+ dash no. 304L or 305
or 316 or
316L

1/ Threads shall be class 3A (UNF-3A) of liandbookH-28, per MIL-S-8879.

~/, ~/ Threads shall be class 2P, (UNC-2A) of Handbook H-28, per MIL-S-7749.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979
TABLE I. Part numbers.

DNom .... .188 .250 .312 .375 .500

*Min. .o, .325 .430 .545 .660 .885
Max..., .355 .460 .575 .690 .915
~Min .. .. .075 .100 .136 .164 .222
Max ..,. .095 .120 .155 .184 .242

“Min .... .208 .268 “ .332 .395 .520

Max .... .218 .278 .342 ,405 .530

~Min ....
Max . ...
.060
.110
,090
.145
.125
.187
.156
.219
,219
.281 I .
Gri range y, q 1/, g/ l_/,2/ .
L or ~/ L & ~/ L or 3_T L L
Min Max

.125 .250 *594 -1 .688 -32 .

.250 .375 .719 -2 .812 -33 .875 -64
.375 .500 ,844 .938 -34 1.000 -65 1.094 -96
.500 .625 .969 :: 1.062 -35 1,125 -66 7.2?9 -97 1.375
.625 .750 1.094 -5 1.188 -36 1.250 -67 1.344 -98 1.500 -129

.750 .875 1.219 -6 1.312 -37 1.375 -68 1.469 -99 1.625 -130
,875 1,000 1 344
● -7 1.438 -38 1.500 -69 1.594 -100 1.750 -131
1.000 1.125 1.469 1.562 -39 1.625 -70 1.719 -101 1.875 -132
1.125 1.250 1 594
● :; 1 688
● -40 1.750 -71 1.844 -102 2.000 -133
1.250 1.375 1.719 -lo 1.812 -41 1.875 -72 1.969 -103 2.125 -134

1*375 1.500 1.844 -11 1.938 -42 2.000 -73 2.094 -104 2.250 -135
1.500 1.625 1.969 -12 2.062 -43 2.125 -74 2.219 -105 2.375 -136
1.625 1.750 2.094 -13 2.188 -44 2.250 -75 2.344 -106 2.500 -137
1.750 1.875 2.219 -14 2.312 -45 2.375 -76 2.469 -107 2.625 -138
1.875 2.000 2.344 -15 2.438 -46 2.590 -77 2.594 -108 2,750 -139

2.000 2.125 2.469 -16 2.562 -47 2.625 -78 2.719 -109 2.875 -140
2.125 2.250 2.594 -17 2.688 -48 2.750 -79 2.844 -110 3.000 -141
2.250 2.375 2.719 -18 2.812 -49 2.875 -80 2.969 -111 3.125 -142
2.375 2.500 2.844 -19 2.938 -50 3.000 -81 3.094 -112 3.250 -143
2.500 2.625 2.969 -20 3.062 -51 3.125 -82 3.219 -113 3.375 -144

2.625 2.750 3.094 -21 3.188 -52 3.250 -83 3.344 -114 3.500 -145
2.750 2.875 3.219 -22 3.312 -53 3.375 -84 3.469 -115 3.625 -146
2.875 3.000 3.344 -23 3.438 -54 3.500 -85 3.594 -116 3.750 -147
3.000 3.125 3.469 -24 3.562 -55 3.625 -86 3.719 -117 3.875 -148
3.125 3.250 3*594 -25 3.688 -56 3.750 -87 3.844 -118 4.000 -149

3.250 3.375 3,719 -26 3.812 -57 3.875 -88 3.969 -119 4.125 -150
3.375 3.500 3.844 -27 3.938 -58 4.000 .89 4.094 -120 4.250 -151
3.500 3.625 3.969 -28 4.062 -59 4.125 -90 4.219 -121 4.375 -152
3.625 3.750 4.094 -29 4.188 -60 4.250 -91 4.344 -122 4.500 -153
3.750 3.875 4.219 -30 4.312 -61 4.375 -92 4.469 -123 4.625 -154

3.875 4.000 4,344 -31 4.438 -62 4.500 -93 4.594 -124 4.750 -155 ‘t-

1/, 1/, l/ (See page 506.1)

506.2
 Downloaded from http://www.everyspec.com

..

MIL”STD-1759
10JULY 1979

TABLE I. Part numbers. - Continued

.750 .875 1.000

DNom ..... “.625

1.110 1.335 1.560 1.785

4
AMin *~@**
Max ..... I 1.140
——
1.365 1.590 1.815

.280 .340 .396 ,455

“Min .....
300 .360 .416 i .475
Max,.... ●

MMin*. ..o .645 .770 I .895 ~ 1 020

●

.655 .780 .905 1.030

- Max .....

.344 .406 .469

.281
JMin* @”**, .469 .531
Max. . . . . .344 .406

Grip range y, y 1/, ~/ L

L L L
or ~/ & .~/
Min Max

- .
500 ,625 1.531 -159
●
- -
,625 ,750 1.656 -160 1.;12 -1;1
.875 1.781 -161 1.938 -192 2.094 -223
,750 -255
-162 2.062 -193 2.219 -224 2.;75
.875 1,000 1.906
2.188 -194 2.344 -225 2 500 -256
1.000 1,125 2.031 -163 ●

-164 2,312 -195 2.469 -226 2,625 -257

1,125 1.250 2.156
-165 2.438 -196 2.594 -227 2.750 -258
!.250 1.375 2.281
-166 2.562 -197 2.719 -228 2.875 -259
1.375 1.500 2.406
2.688 -198 2.844 -229 3.000 -260
1 500 1.625 2,531 -167
●

2.812 -199 2.969 -230 3.125 -261

1.625 1*750 2.656 -168

-169 2.938 -200 3.094 -231 3.250 -262

1.750 1.875 2.781
3.062 -201 3.219 -232 3*375 -263
1,875 2.000 2.906 -170
-171 3.188 -202 3.344 -233 3.500 -264
2.000 2.125 3.031
3.312 -203 3.469 -234 3.625 -265
2.125 2.250 3.156 -172
3,438 -204 3.594 -235 3.750 -266
2,250 2.375 3.281 -173

-174 3,562 -205 3.719 -236 3.875 -267

2,375 2.500 3.4;6
-175 3*688 -206 3.844 -237 4,000 -268
2,500 2.625 3.531
-176 3.812 -207 3.969 -238 4,125 -269
2,625 2.750 3.656
3.938 -208 4,094 -239 4,250 -270
2,750 2.875 3.781 -177
-178 4.062 -209 4,219 -240 4.375 -271
2,875 3 000
● 3.906

4,188 -210” 4 *344 -241 4.500 -272

3.000 3.125 4.031 -179
-180 4,312 -211 4,469 -242 4.625 -273
3.125 3.250 4.156
-181 4.438 -212 4.594 -243 4.750 -274
3.250 3.375 4,281
-182 4,562 -213 4.719 -244 4.875 -275
3.375 3.500 4.406
-183 4,688 -214 4.844 -245 5 000 -276
4.531
●

3.500 3.625

4.812 -215 4.969 -246 5.125 -277

3.625 3?750 4,656 -184
-216 5.094 -247 5.250 -278
3.750 3.875 4.781 -185 4,938
-217 5.219 -248 5.375 -279
3.875 4.000 4.906 -186 5.062
L
~/, z_/,Y (See page 506.1)

506.3
--
Downloaded from http://www.everyspec.com
.
.

--

.
 Downloaded from http://www.everyspec.com

..

-----
MIL-STII-1759
10JULY 1979

SECTION507

PIN-RIVET,
THREADED,
60°COUNTERSUNKOVAL
HEAD,STRAIGHTSHANK
APPLICABLE DOCUMENT: MIL-P-23470/7,/l
1,/16

-. .

Part numbers Material Protective finish Shear strength

Footnotes
(psi) min

M23470/16 Aluminum alloy Anodic 24,950

~/
+ dash no. 6061-T6 coat

M23470/7 Carbon steel Zinc plate 68,400

g/
+ dash no. ASTM A546

1423470/11 Cres 304 or - Passivate 68,400

q
+ dash no. 3041 or 305
or 316 or 316L

1/ Threads shall be class 3A (UNF-3A) of Handbook H-28 per ‘411-S-8879.

~/
— Threads shall be class 2A (UNF-2/~)of Handbook H-28per MIL-S-8879.

.
 Downloaded from http://www.everyspec.com

MIL-sTD-1759
10JULY 1979

TABLE I. Part numbers.

D Nom dia.., .500 .625 .750 I

.780 .981 1.176
A Dia Mira..
Max. .
● .812 1.011 1.212 I
Min ““ .313 .375
H
Max .. .332 .395 I
“

Grip
range L L L

dash dash dash

Min Max Length Length Length
numbers 7 umbers lumbers ,

.062 .188 .844 -1 .906 -33 1.031 -65

.188 .312 .969 -2 1.031 -34 1.156 -66
.312 .438 1.094 -3 1.156 -35 1.281 -67
.438 ,562 1.219 -4 1.281 -36 1,406 -68
.562 .688 1.344 -5 1.406 -37 1.531 -69

.688 .812 1.469 -6 1.531 -38 1.656 -70

.812 .938 1.594 -7 1.656 -39 1.781 -71
.938 1.062 1.719 -8 1.781 -40 1.906 -72
1.062 1.188 1.844 -9 1.906 -41 2.031 -73 I
1.188 1.312 1.969 -lo 2.031 -42 2.156 -74

1.312 1,438 2.094 -11 2.156 -43 2,281 -75

1.438 1.562 2.219 -12 2.281 -44 2.406 -76
1.562 1,688 2.344 -13 2.406 -45 2.531 -77
1.688 1.812 2.469 -14 2.531 -46 2.656 -78
1.812 1.938 2.594 -15 2.656 -47 2.781 -79

1.938 2.062 2.719 -16 2.781 -48 2.906 -80

2.062 2.188 2.844 -17 2.906 -49 3.031 -81
.
2.188 2.312 2.969 -18 3.031 -50 3,156 -82
2.312 2.438 3.094 -19 3.156 -51 3.281 -83
2.438 2.562 3.219 -20 3.281 -52 3.406 -84

2.562 2.688 3.344 -21 3.406 -53 3.531 -85

2.688 2.812 3.469 -22 3.531 -54 3.656 -86
2.812 2.938 3.594 -z? 3.656 -55 3.781 -87
2.938 3.062 3.719 -24 3.781 -56 3.906 -88
3.062 3.188 3.844 -25 3.906 -57 4,031 -89

3.188 3.312 3,969 -26 4.031 -58 4.156 -90

3.312 3.438 ~.~g~ -.
:7 il.1~~ -59 4,281 -91
3.438 3.562 4,2~9 -28 ~.281 -60 4,406 -92
3.56? 3.6E8 4.244 .70 4.406 -61 4.531 -93
3.588 3.812 4.469 -ii 4.531 -62 4.656 -94

3.812 3,938 4.594 -31 4.656 -62 4.781 -95

3v~38 4.062 4.719 -32 4.781 -64 4,906 -96
 Downloaded from http://www.everyspec.com

-%.-
MIL-STD-1759
10JULY 1979

SECTION508

PIN-RIVET,
THREADED,60°COUNTERSUNKOVAL
HEAD,TAPEREDSHANK
APPLICABLEDOCUMENTS:MlLoP=23470/8.
12.17

READ

Footnotes Part Numbers Material Protective finish Shear strength

(psi) min

~/ M23470/17 Aluminum Anodic coat 24,950

+ dash no. alloy
● 6016-T6

g[ tv123470~8 Carbon steel Zinc plate 70,500

+ dash no. ASTM A546

~/ ‘ M23470/12 Cres steel Passivate 68,400

+ dash no. class 304 or
304L or 305
or 316 or
316L

1/ Threads shall be class 3A (UNF-3A) of Handbook H-28, per MIL-S-8879.

~/ Threads shall be class 2A (UNC-2A) of Handbook H-28, per MIL-S-7742.

* 508.1
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759 -
10 JULY 1979

TABLE I. Part numbers.

4

D Dia nom.. .312 .375 .500

=lK
.458
.478
.556
.576
.758
.778 I
H
I Min.,
Max”9
.117
.137
.147
.167
.211
.231

IIDia Min.. .332 .395 .520

]f tapeJ Max.. .342 .405 .530
4
●219
) Length
]f tape J Min..
Maxoo
.125
.187
.156
.219 .281 I
Grip L L
L
range

dash dash
Min Max Length
dash
lumbers
Length
numbers
Length
numDers I
.375 .500 1.000
.500 .625 1.125 :; 1.219 -31
.625 .750 1.250 -3 1.344 -32 1,;00 -61
.750 .875 1.375 -4 1.469 -33 1.625 -62 -;2
.875 1 000
● 1.500 -5 1.594 -34 1.750 -6: -63

1.000 1.125 1.625 -6 1.719 -35 1.875 -64 -64

1.125 1.250 1.750 -7 1.844 -36 2.000 -65 -65
1.375 1.875 -8 1.969 -37 2.125 -66 -66
1.250
1.375 1.500 2.000 -9 2.094 -38 2.250 -67 -67
1.625 2.125 -lo 2.219 .>9 2.375 -68 -68
1.500

1.625 1.750 2.250 -11 2.344 -40 2.500 -69 -69

1.750 1.875 2.375 -12 2.469 -41 2.625 -70 -7C
1.875 2.000 2.500 -13 2.594 -42 2.75G -71 -71
2.125 2.625 -14 2.7”I9 -43 2.875 -72 -72
2.000
2.250 2.750 -15 2.844 -44 3.000 -73 -73
2.125

2.375 2.875 -16 2.969 -45 3.125 -74 -74

2.250
2.375 2.500 3.000 -17 3.094 -46 3.250 -75 -75
2.625 3.125 -18 3.219 -47 3.375 -76 -76
2.500
3.250 -19 3.344 -48 3.5-jo -77 -77
2.625 2.750
-20 3.469 -49 3.625 -78 -78
2.750 2.875 3.375

3.000 3.500 -21 3.594 -50 3.750 -79 -79

2.875
3.625 3.719 -51 3.875 -80 -80
3.000 3.125 -22
3.750 -23 3.844 -52 4.000 -81 -81
3.125 3.250 -82
3,250 3.375 3.875 -24 3.969 “52 4, 125 -82
-~~
3,375 3, ~oo 4.000 .25 4.094 -54 4.250 -82

3.500 3.625 4,125 -26 4,219 -~~ 4,275 -84 -84

4.344 4,500 -as -85
3.625 3.750 4.250 -27 -56
4.275 4.469 -57 4.625 -86 -86
3.750 3.875 -28 -. v
3,875 4,000 4.500 .~o
. 4.594 -58 40.,,: -87 -87
A

508.2
,\ ~},
 Downloaded from http://www.everyspec.com

.
.

.:.

MIL-STD-1759
10 JULY 1979

TABLE 1. part numbers. - Continued

D Dia nom,. .625 .750 ,875 1.000

1
1,122 ~ 1.304 1.485
1.163 1.355 -i 1.542
Min , .333 393 .454
H Max , *
●

.353 .413 ,474

M Dia Mint .645 ●770 .895 1.020
+of tape Maxa .655 .780 ●905 +
— 1.030
I

.344 ,406 .469 I

.406 .469 .531 I

Grip L L L L
range

dash dash
Min Max Length Length Length Length
numbers number

.625 .75( 1.656 -90 1.188 -119 . . . .

.750 .871 1.781 -91 1.312 -120 - .
.875 1.00( 1.906 -92 -9; 2.062 -121 . - .
1.000 1.12! 2.031 -93 -93 2.188 -122 -i 2,344 -1;1
1.125 1.25[ 2.156 -94 -94 2.312 -123 -12: 2.469 -152 -15; .

1.250 1.37! 2.281 -95 -95 2.438 -124 -124 2.594 -153 -15: 2.750 -182
1.375 1.50C 2.406 -96 -96 2.562 -125 -12! 2.719 -154 -15f 2,875 -183
1.500 1.625 2.531 -97 -97 2.688 -126 2.844 -155 -15! 3.000 -184
-12(
1.625 1.75C 2.656 -98 -98 2.812 -127 -12; 2.969 -156 -15[ 3.125 -185
1.750 1.875 2.781 -99 -99 2.938 -128 -12[ 3.094 -157 -157 3.250 -186

1.875 2.000 2.906 -1oo -100 3.062 -129 .lzf 3.219 -158 -15E 3.375 -187
2.000 2.125 3.031 -101 -101 3.188 -130 -13( 3.344 -159 -15s 3.500 -188
2.125 2,250 3.156 -102 -102 3.312 -131 -131 3.469 -160 -16C 3.625 -189
2.250 2.375 3.281 -103 -103 3,438 -132 “132 3.594 -161 -161 3.750 -190
2.375 2.500 3.406 -104 -104 3.562 -133 -13: 3.719 -162 -162 3.875 -191

2.500 2.625 3.531 -105 -105 3.688 -134 .134 3.844 -163 -163 4.000 -192
2.625 2.750 3.656 -106 -106 3.812 -135 9133 3.969 -164 -164 4.125 -193
2.750 2.875 3.781 -107 -107 3.938 -136 ●136 4.094 -165 -165 4,250 -194
2.875 3.000 3.906 -108 =108 4.062 -137 ,137 4.219 -166 “166 4.375 -195
3.000 3.125 4.031 -109 -109 4.188 -138 .138 4,344 -167 -167 4.500 -196

3.125 3.250 4,156 -110 -110 4.312 -139 139 4.469 -168 .168 4.625 -197
3.250 3.375 4.281 -111 .111 4.438 -140 140 4*594 -169 ●169 4.750 -198
3.375 3.500 4.406 -112 .112 4.562 -141 141 4.719 .170 .170 4.875 -199
3*500 3,625 4.531 -113 .113’4.688 -142 142 4,844 -171 -171 5.000 -200
3,625 3*750 4.656 -114 ,114 4.812 -143 143 !,969 .172 .172 5.125 -201
3*750 3.875 4.781 -115 ,115 4.938 -144 144 5.094 -173 .173 5.250 -202
3.875 4.000 4.906 -116 116 j.062 -145 145 5.219 .174 ,174 5.375 =203
—
Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

.:.

MI L-STD-1759
10 JULY 1979

SECTION509

PIN-RIVET,
THREADED,
90°COUNTERSUNK
FLATHEAD,STRAIGHTSHANK
APPLICABLEDOCUMENT: MlL=P423470/4,
9.13

THREAD

..-

Footnotes Part Numbers Materials Protective finish Shear strength

(psi) min

y M23470/13 Aluminum alloy Anodic coat 24,950

+ dash no. 6061-T6

~1 M23470/4 Carbon steel Cadmium plate 68,400

+ dash no. ASTM A546

~1 M23470/9 ● Cres 304 or Passivate 68,400

+ dash no. 304L or 305
or 316 or
316t.

1/: Threads shall be class 3A (UNF-3A) of Handbook H-28 per ;~IL-S-~g~SO

2/, ?/:
-— Threads shall be cJass 2A (UNF-2A)of Handbook H-28per W-S-S879.

509.1
 Downloaded from http://www.everyspec.com

=. .
.

MIL-STD-1759
IOJULY 1979

TABLE I. Part numbers.

DNom . . . . . .188 I .250 .312 .375

*Min . . . . . ●340 .455 .569 .682

Max. . . . . .351 .469 .588 .704

~Min. ..o. .075 .101 .127 .152

Max. . . . . .085 .113 .141 .166

Grip range y, 2/ ~ :;, 32 ~ y, 2/ ~ ;;, 3#

L
Min Max or 27 / or 27

.062 ,188 .531 -1 .594 -33 .656 -65 .719 -97

.188 .312 .656 -2 .719 -34 .781 -66 .844 -98
.312 .438 .781 -3 .844 -35 .906 -67 .969 -99
.438 .562 .906 -4 .969 -36 1.031 -68 1.094 -100
.562 ●688 1.031 -5 1.094 -37 1.156 -69 1.219 -101

,688 .812 1.156 -6 1.219 -38 1.281 -70 1.344 -102

.812 .938 1.281 -7 1 344
● -39 1.406 -71 1.469 -103
.938 1.062 1.406 -8 1.469 -40 1.531 -72 1.594 -104
.062 1.188 1.531 -9 1.594 -41 1.656 -73 1.719 -105
.188 1.312 1.656 -lo 1.656 -42 1.781 -74 1.844 -106
-
.312 1.438 1.781 -11 1.844 -43 1.906 -75 1.969 -107
14.438 1.562 1.906 -12 1.969 -44 2.031 -76 2.094 -108
1(.562 1.688 2.031 -13 2.094 -45 2.156 -77 2.219 -109
14 688
● 1.81-2 2.156 -14 2.219 -46 2.281 -78 2.344 -110
1(.812 1.938 2.281 -15 2.344 -47 2.406 -79 2.469 -111

14.938 2.062 2.406 -16 2.469 -48 2.531 -80 2.594 -112
24.062 2.188 2.531 -17 2.594 -49 2.656 -81 2.719 -113
2,t188 2.312 2.656 -18 2.656 -50 2.781 -82 2.844 -114
2,,312 2.438 2.781 -19 2.844 -51 2.906 -83 2.969 -115
2 ,438 2.562 2.906 -20 2.969 -52 3.031 -84 3.094 -116

24,562 2,688 3.031 -21 3.094 -53 3.156 -85 3.219 -117
2<,688 2.812 3.156 -22 3.219 -54 3.281 -86 3.344 -118
2<,812 .2.938 3.281 -23 3.344 -55 3.406 -87 3.469 -119
2 ,938 3.062 3.406 -24 3.469 -56 3.531 -88 3.594 -120
3,)062 3.188 3.531 -25 3.594 -57 3.656 -89 3.719 “121

3,,188 3.312 3.656 -26 3.656 -58 3.781 -90 3.844 -122
34,312 3.438 3.781 -27 3.844 -59 3.906 -91 3.969 -123
3!,438 3.562 3.906 -28 3.969 -60 4.031 -92 4.094 -124
3$,562 3.688 4.031 -29 4.094 -61 4.156 -93 4.219 -125
3.,688 3.812 4.156 -30 4.219 -62 4.281 -94 4.344 -126

3,,812 3.938 4.281 -31 4.344 -63 4.406 -95 4.469 -127
3 ,938 4.062 4.406 -32 4.469 -64 4.531 -96 4.594 -128
—

~/, Z_/,~/ (see page 509.1)0

509 2●

t.
 Downloaded from http://www.everyspec.com

. .

MIL-STD-1759
L

10JULY 1979

TABLE 1, Part numbers. - Continued

11Nom.,.. .438 .500 .625 .750

AMin=Hu .797 .916 1.139 1.388

Max. . . . . ,823 .946 1.175 1*41O
I
“Min . . . . . .179 .208 .258 .311
Ma~.... .193 ● 222 .274 .327

Grip range lf, ZJ

L ~/, g/ L y, 2/ ‘ IJ, q L
Min Max or ~/ or ~T or ~/ or 3J

.062 ● 188 .781 -129 .844 -161 .906 -193 1.031 -225
.188 .312 .906 -130 .969 -162 1.031 -194 1.156 -226
.312 .438 1.031 -131 1 094
● -163 1.156 -195 1.281 -227
.438 .562 1.156 -132 1.219 -164 1.281 -196 1.406 -228
.562 ,688 .1.281 -133 1.344 -165 1.406 -197 1.531 -229

● 688 ,812 1.406 -134 1.469 -166 1.531 -198 1.656 -230
.012 .938 1.531 -135 1.594 -167 1.656 -199 1.781 -231
.938 1.062 1,656 I -136 1.719 -168 1.781 -200 1.906 -232
1.062 1 *188 1.781 -137 1.844 -169 1.906 -201 2.031 -233
1.188 1.312 1.906 -138 1.969 -170 2.031 -202 2.156 -234

1.312 1.438 2.031 -139 2.094 -171 2.156 -203 2.281 -235
1.438 1.562 2.156 -140 2.219 -172 2.281 -204 2.406 -236
1.562 1,688 2.281 -141 2.344 -173 2.406 -205 2.531 -237
1.688 1.812 2.406 -142 2.469 -174 2.531 -206 2.656 -238
1.812 1.938 2.531 -143 2.594 -175 2.656 -207 2.781 -239

1.938 2.062 2.656 -144 2.719 -176 2.781 -208 2.906 -240
2.062 2,188 2.781 -145 2.844 -177 2.906 -209 3.031 -241
2.188 2.312 2.906 -146 2.969 -178 3.031 -210 3.156 -242
2.312 2.438 3.031 -147 3.094 -179 3.156 -211 3.281 -243
2.438 2.562 3.156 -148 3.219 -180 3.281 -212 3.406 -244

2.562 2.688 3.281 -149 3 344

● -181 3.406 -213 3.531 -245
2,688 2.812 3.406 -150 3.469 -182 3.531 -214 3.656 -246
2.812 2.938 3.531 -151 3 ,594 -183 3.656 -215 3.781 -247
2.938 3.062 3.656 -152 3.719 -184 3.781 -216 3.906 -248
3.062 3.188 3.781 -153 3.844 -185 3.906 -217 4.031 -249

3.188 3.312 3.906 -154 3.969 -186 4.031 -218 4 .156 -250
3.312 3.438 4 .031 -155 4 094
● -187 4 .156 -219 4.281 -251
3.438 3.562 4.156 -156 4.219 -188 4.281 -220 4 .406 -252
3.562 3.688 4.281 -157 4.344 -189 4.406 -221 4 .531 -253
3.688 3.812 4 .406 -158 4 .469 -190 4.531 -222 4 .656 -254

3.812 3.938 4.531 -159 4.594 -191 4 .656 -223 4 .781 -255
3.938 4.062 4 .656 -160 4 ,719 -192 4.781 -224 4.906 -256

l/. ~/, 3f (See page 509.1)

509.3
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

-.
MIL-STD-1759
10 JULY 1979

SECTION510

PIN-RIVET,
THREADED,
NAILHEAD,
STRAIGHTSHANK,CORROSIONRESISTANTSTEEL
APPLICABLEDOCUMENT: MIL-P-23470/3

H
THREAD q 1

Shear strength
Material Protective finish
(psi) min

Cres 304 or
304L or 305
Passivate 68,400
or 316 or
316L .

TABLE I. Pin-rivet, threaded, configuration,

A H
Dia

Nominal Min Max Min Max

.250 ,740 ,750 .084 0094

NOTE : Threads shall be class 2A (UNF-2A) of Handbook ti-2!3per MIL-S-8879.

. . 510.1
 Downloaded from http://www.everyspec.com
.

..

MIL-STD-1759
10 JULY 1979

TABLE 11. M23470/3 Dash numbers.

Dminal diameter

.: 0
Grip range
L Dash
Max .ength ~umber
Min
.062 .188 .594 -1
.188 .312 .719 -2
.312 .438 .844 -3 b

.438 .562 .969 -4

.562 .688 1.094 -5
.
.688 .812 1.219 -6
.812 .938 1.344 -7
.938 1.062 1.469 -8
1.062 1.188 1.594 -9
1.188 1.312 1.719 -lo

1.312 1.438 1.844 -11

1.438 1.562 1.969 -12
1.562 1 688
● 2.094 -13
1.688 1.812 2.219 -14
1.812 ~ 1.938 2.344 -15

1.938 2.062 2.469 -16

2.062 2.188 2.594 -17
2,188 2.312 2.719 -18
2.312 2.438 2.844 -19
2.438 2.562 2.969 -20

2.562 2.688 3.094 -21

2.688 2.812 3.219 -22
2.812 2.938 3.344 -23
2.938 3.062 3.469 -24
3.062 3.188 3.594 -25

3.188 3.312 3.719 -26

3.312 3.438 3.844 -27
3.438 3.562 3.969 -28
3.562 3,688 4.094 -29
3.688 3.812 4.219 -30

3.812 3.93f 4 344

● -31
3.938 4.062 4.469 -32
 .
Downloaded from http://www.everyspec.com

.:.

MIL-STD-1759
10 JULY 1979

SECTION511

PIN-THREADED
SHEAR100°CSK HEAD
APPLICABLEDOCUMENT: NAS1292THRU 1296

1 I I

.-2 DIA lfifl”

--- -1 REF
I Uv
I

D
T
11( DCC GRIP -1 ~
AL I
RANGE

Shear strength
Material Protective finish
Code
(psi) min

Nickel-zinc alloy
plate and hydrogen
Alloy steel embrittlement
H-n 151,400 J

Diffus;~ nickel-
cadmium plate
Nickel base
alloy None 97,000 R
RENE’ 41

TABLE I. NAS1 92 thru 1296 part numbers

D ‘1 B T Basic
Thread Dia Min Head Ref part
ma x height number

.1640-32 UNJC .1635 ,220 .042 .308 NAS1292

.1900-32 UNJF .1895 .258 .048 .328 NAS1293
.2500-28 UNJF .2495 ●350 .063 .377 NAS1294
.3125-24 UNJF .3120 .429 .070 .429 NAS1295
,3750-24 UNJF :3745 .515 .081 .469 NAS1296

NOTES :

1. The dash number following the material code “J” or “R”

indicates grip range in ~0625 increments up to and
including “-18” (1-1/8).
2. Temperature limitation: H-11: 800° F max
RENE’ 41: 1400° F max
511.1
I
Downloaded from http://www.everyspec.com

(’l
f).
 Downloaded from http://www.everyspec.com

---

MIL-STD-1759
10 JULY 1979

SECTION512

PIN-THREADED
SHEARPROTRUDINGHEAD
APPLICABLEDOCUMENT: NAS1322THW 1326

o+
@

Shear strength
Material Protective finish
(psi) min Code

Nickel-zinc alloy
plate and hydrogen
Alloy steel
embrittlement
H-II 151,400 J

Diffus~! nickel-
cadmium plate
N~ckel base
a?loy None 97,000 R
RENE’ 41
TABLE I. NAS1322 thru 1326 oart numbers.

D A B T Basic
Thread Dia Min Head Ref part
max number

.262 .047
,1640-32 UNJC .1635 .308 NAS1322
I
.242 .037
.315 .055
I .1900-32 UNJF .1895
.295 ●045
.328 NAS1323
t .412 ,069
I .2500-28 UNJF .2495 ● 377 NAS1324
,387 .059
1 .078
●505
I .3125-24 UNJF .3120 .429 NAS1325
.475 .068
t
,600 .088
I
L
.3750-24 UNJF ● 3745
.565 .078
.469 NAS1326

NOTES :
1. The dash number following the material code “J” or “R”
indicates grin range in ;0625 increments up to and
including “+3” (1-1/8),
2. Temperature limitation: H-II: 800° F max
RENE’ 41: 14000 F max

512.1
Downloaded from http://www.everyspec.com

-
 Downloaded from http://www.everyspec.com

-
“.

.— MIL-STD-1759
10 JULY 1979

SECTION601

FASTENER,
BLIND,
HIGHSTRENGTH,PULLTYPE,POSITIVE
MECHANICALLOCK,
100°FLUSHHEAD,CORROSIONRESISTING
STEEL95 KSIFsu
APPLICABLEDOCUMENT: MS21140

1000

Shear strength
Material Protective finish
(psi) min

Cres Passivate or 95,000

15Cr-26#i cadnium pla~

TABLE 1. Rivet configuration.

D
Nom B A
size Max 01a

.156 .074 .334

.188 .082 ,387
.250 ●108 .508
.312 .140 .635
0375 .168 .763

601.1
/
 Downloaded from http://www.everyspec.com

MIL-STD”1759
10 JULY 1979

Orlm I%or-lmh
I mtn. bwobow
-corn ao--(w
,... . . . .
o
----
m
r-
m
.

—
.
Uma bamo- Nmwlna
I Oco 000-- -----
Oco 00000 00000
--- -- - - . - -- --
Ill 1111111 811

.
u
n

.,,. . . . . . . . . .
F----

--- -----

x
2
—
c
.-
S

.601.2
c-
.1
 Downloaded from http://www.everyspec.com
.

.. .

MIL-STD-1759
10 JULY 1979

SECTION602

FASTENER,
BLIND,
HIGHSTRENGTH,PULLTYPE,POSITIVEMECHANICALLOCK,
PROTRUDINGHEAD,CORROSIONRESISTING
STEEL95 KSIFsu,
APPLICABLEDOCUMENT: MS21141

AJ

Shear strength
Material Protective finish
(psi) min

Cres Passivate or 95,000

15Cr-26Ni cadmium plate

TABLE I. Rivet configuration.

Nom A
B
size Ilia
.
.272 .070
.156
.250 .062

.332 .135
I .188
●305 .125

r .250
.432 .140

r
,400 .130

.522 .141
.312 .480 .131
.627 .205
I .375
.580 .195

602.1
 Downloaded from http://www.everyspec.com

-.

MIL-STD-1759 ---
10JULY 1979

. . . . . . . .-. . . . . . .
------

n L I
---

, ,
I

.
n.c
.;:O

amcl I ----- -----

Nmqbn

I gggg
gogm~
00000

l“’’’’’’’’’’’”
.Iwf’-ehnw
-----
-----
00000 z

---- ----
-Nm=m
00000
Ulmmlnul
Whamo
0000-
-Nnwmw
----- - I
Lnlnmmul Lnmulu-lul m
yyyoy 00000
11888
yoooo 11 t,,
o

---

602.2
/4(7/
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION603

FASTENER-BLIND,
INTERNALLYTHREADED,
EXTERNALSLEEVE,
FLUSHHEAD,SELF-LOCKING
APPLICABLE
DOCUMENTS: NAS1670,NAS1672

+
“@ VI i
7-+H+

Footnotes Part numbers Material Protective finish Shear strength

(psi)

Corrosion 63,900
l_/ NAS1672 to
+ dash no. and heat Passivate
resisting 72,100
steel
A286
78,225
to
~/ NAS1670 Alloy steel Cadmium plate 88,275
+ dash no.

I_/ Temperature limitation; 1200”F max~

~/ Temperature limitation; 450”F max.

.603.1
 .
Downloaded from http://www.everyspec.com

-.

MIL-STD-1759
10 JULY 1979

603.2
A-A
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION604

FASTENER-BLIND,
INTERNALLY
THREADED,EXTERNALSLEEVE,
PROTRUDINGHEAD,SELF-LOCKING
Applicable
DOCUMENT:NAS 1669,
NAS 1671,
NAS 1673

IA
r--
I
L --

?
Material protective finish Shear strength
Footnotes Part numbers
(psi)

Alloy steel Cadmium plate 78,225

~/ NAS 1669
to
88,275
,

Corrosion and Passivate 63,900 “

~1 NAS 1671
. heat resisting to
steel A286 72,100

Aluminum Anodize (clear) 45,400

J/ NAS 1673
alloy to
7075 50,000
. b

~/ Temperature limitation; 450°F max.

~/ Temperature limitation; 1200°F max.
~/ Temperature limitation; 250°F max.

, 604,1
 Downloaded from http://www.everyspec.com
. .

.:.

MIL-STD-1759
JULY 1979

— —

0- 0
E
m
g:
. . m.

— —
-
mJl

L
0
●
z
u \
. -1

e
m
f=)
.

.
.
F
#
.

------ -----
*
—

aJ
@
ul
u

. . . . . . . . . . . . . . . . —.—.... . . .
----- ---
<
WI

c1

604.2 c-
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION605

FASTENER-BLIND,
INTERNALLY
THREADED,EXTERNALSLEEVE,
LIGHTWEIGHT,
MILLABLEHEAD,SELF-LOCKING
APPLICABLEDOCUMENT: NAS1674

I----L--I

v 4Ti-

Shear strength
Material Protective finish (psi)

Aluminum Anodize (clear) 45,400 to 50,000

7075

TABLE I. Rivet configuration.

D T Basic
A
c H s
Nom Ref part number
Max
dia

.283 .074 .054 .049 NAS1674-08L( )

.164 .268 ,044
.277 .067

.346 .079 ● 059 .061 NAS1674-3L( )

.200 .303 .049
.332 .072

.472 .079 .059 .088 NAS1674-4L( )

.260 .354 .049
.458 .072

1
 Downloaded from http://www.everyspec.com
.

..

MIL-STD-1759 ---
10 JULY 1979

TABLE II. NAS1674 Dash numbers.

Grip range L Second

G dash
Min Max -08L( ) -3L( ) -41( ) number

.156 .094 .156 .795 .936 .960 -2

.219 .157 .219 .858 .999 1.023 -3
.281 .220 .281 .920 1.061 1.085 -4
●344 .282 344● .983 1.124 1.148 -5
.406 .345 .406 1..045 1.186 1.210 -6

.469 .407 .469 1.108 1.249 1.273 -7

.531 .470 .531 1.170 1.311 1.335 -8
.594 .532 ●594 1.233 1.374 1.398 -9
.656 .595 .656 1 a295 1.436 1.460 -lo -
.719 .657 .719 1.358 1.499 1.523 -11

.781 .720 .781 1.420 1.561 1.585 -12

,844 .782 .844 1.483 1.624 1,648 -13
,906 .845 .906 1,545 1.636 1.710 -14
.969 ●907 .969 1.608 1.749 1.773 -15
,031 0970 10031 1.670 1.811 1.835 -16

.094 1.032 1 094

● 1.874 1.898 -17
.156 1.095 1.156 1.936 1.960 -18
.219 ~0157 1.219 1.999 2.023 -19
.281 1.220 1.281 2.061 2.085 -20

605.~

b
 Downloaded from http://www.everyspec.com

.:.

----
MIL-STD-1759
10JULY 1979

SECTION
606

RIVET,
BLIND-COUNTERSUNK
HEAD,DRIVETYPE
APPLICABLEDOCUMENT: MS24861

p4
,----- ---- 100°
I ,91 ~7
81, b---
\...--%-. D

AJ y ‘“ ‘-‘‘
>
GRIP
L.

G RANGE J

Shear strength
Material Protective finish (psi) min
[

Aluminum ~lloy

Carbon steel

‘—
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers.

7

B
Head D IM524661Dash no.
A L
Dia height Head Grip ranqe Aluminum Carbon
ref Min Max Length -*,]7 \ 5056 steel
dia

.078 .109 .188 -5 -168 -6

.110 .140 .219 -7 -169
.141 .171 .250 -9 -170 -i:
.172 .203 .281 -11 -171 -12
.204 .234 .312 -13 -172 -14
.125 .042 .225 .235 .265 .344 -15 -173 -16
.266 .296 .375 -17 -174 -18
.
.297 .328 .406 -19 -175 -20
.329 .359 .438 -21 -176 -22
.360 .390 .469 -23 -177 -24
.391 .421 .500 -25 -178 -26

.109 .140 .250 -31 -179 -32

.141 .171 .281 -33 -180 -34
172 .203 .312 -35 -181 -36
:204 .234 .344 -37 -182 -38
.235 .265 .375 -39 -183 -40
.266 .296 .406 -41 -184 -42
.297 .328 .438 -43 -185 -44
.329 .359 .469 -45 -186 -46
.156 .055 .286 .360 .390 .500 -47 -187 -48
.391 .421 .531 -49 -188 -50
.422 45j .562 -51 -189 -52
.454 :484 .594 -53 -190 -54
.485 .5i5 .525 -55 -191 -56
.516 .546 .656 -57 -192 -58
.547 .S?e .688 -59 -193 -6(J
.579 .609 ,719 -61 -194 -62
.610 .640 .750 .~~ -195 -64

.109 171 .281 -150 -196 -214

172 :224 .344 -151 -197 -215
:235 .296 .406 -152 -198 -216
.297 .359 .469 -153 -199 -217
,188 .070 .353 .360 .421 .531 -154 -200 -218
.422 .484 .594 -155 -201 -219
.485 .546 .656 -156 -202 -220
.547 .609 .719 -157 -203 -221
.610 .671 .781 -159 -204 -222

.109 .171 .281 -159 -205 -223

172 .224 .344 -160 -206 -224
:235 ,296 .406 -161 -207 -225
.297 .359 .469 -162 -208 -226
.250 .095 ,476 .360 .421 ,531 -163 -209 -227
.422 ,484 .594 -164 ,-210 -228
.485 .546 ,656 -165 I-211 -~~~
.547 ,609 719 -166 ‘-z?~ -2S0
.610 .671 .7s1 -167 -~]~ -231
I
 Downloaded from http://www.everyspec.com

---

-----
MIL-STD-1759
10 JULY 1979

SECTION607

RIVET-BLIND,
100°FLUSHHEAD,LOCKEDSPINDLE
APPLICABLEDOCUMENT: NAS1399

TB

L I-A
O.-C
REF
-.-

,
Shear strength
Material Protective finish ~ (psi) 1
i

Aluminum alloy
“5056F Anodize or chemical .19,750 to 31,265
surface treatment 25,02~
2017-T4
Nickel,copper
.. Cadmium plate or 36,325 to 57,875
~el)
silver plate 49,350 to 79,250
.K~2 H-L09 ●

TABLE 1. Rivet configuration.

T

Rivet
A B c diameter
Dia Dia Ref number

,125 ,225 .042 4

L

,156 .286 .055 5

,190 .353 .070 6
,250 ,476 .095 8

607.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

. . . . . . . . . . , “1

. . . . . . .
I
In-m-t-t
wm~mml I I I I I I I
. . . . .

. . . . .

mwmem
W(wmm-1 I I I I I I I

.,..
0$--twr’l
.

Ommmo
@mm=P-1 I I I I , , ,
wmmwm
..,. .

607.2
..
nfi)
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

sECTION608

RIVET-BLIND,
100°FLUSHHEAD,
MECHANICALLYLOCKEDSPINDLEBULBEO
APPLICABLEDOCUMENT: NAS1739

100°

Shear strength
Ilaterial Protective finish (psi)

Aluminum 5056 Anodize or chemical 36,300 to 50,500

surface treatment

Nickel, cower None Or cadmium 43,800 to 73,000

alloy (Monql) PIate

TABLE 1. Rivet configuration.

A E c
Dia Ref

.140 ,225 ,035

.173 .286 .047

.201 ,353 .063

6G3 .1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

u
 Downloaded from http://www.everyspec.com

.:

MIL-STD-1759
10 JULY 1979

SECTION609

RIVET,
BLIND-GENERAL
PURPOSE,BULBE!l,
100°FLUSHHEMI,MECHANICALLY-LOCKED-SPINDLE
APPLICABLEDOCUMENT: NAS1921

I .
,1 p
.-—--
—.-— -Q—
.

%IIE-
.. J,,
—-.-—
—..—-
1000
B

\ t 7 LA
-
\—/
v

Shear strength
Material Protective finish (psi)

Aluminum 5056 None 38,400 to 40,400

Cres A-286 Passivate or cad- 84,600 to 88,900

mium plate or
aluminum coating

Nickel, copper None or cadmium 79,700 to 83,200

alloy (Monel) plate or aluminum
coating

TABLE I. Rivet configuration.

f
Dia
A B c dash
Dia Dia Ref number

.125 .225 .042 -04

.156 .286 .055 “-05

.187
I .353 .070 -06 I
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

609.2
 Downloaded from http://www.everyspec.com

-%.
MIL-STD-1759
10 JULY 1979

SECTION61O

RIVET,
BLIND-GENERAL
PURPOSE,BULBED,PROTRUDINGHENI,
MEIXiAiilCALLY-LOCKED-SPINDLE
APPLICABLEDOCUMENT: NAS1919

c
7

-----

Shear strength
Material Protective finish
(psi)

Aluminum 5056 None 38,400 to 40,000

Cres A-286 Passivate or cad- 84,600 to 88,900

mium plate or “
aluminum coating

Nickel, coppe None or cadmium 79,700 to 83,200

alloy (Monel) plate or aluminum
coating

TABLE I. Rivet configuration.

B c Dia
A
dash
Dia Dia number

.125 ●250 .054 -04

.156 .312 .067 -05

.187 .375 .080 -06

610.1
—
Downloaded from http://www.everyspec.com

-:..

MIL-STD-1759
10 JULY 1979

Al

d
<
1-

610.2 .. .
 Downloaded from http://www.everyspec.com

>..
MIL-STD-1759
10 JULY 1979

SECTION611

RIVET,BLIND,HIGHSTRENGTH,PULL TYPE,POSITIVEMECHANICALLOCK,
100”FLUSHHEAD,A
LLOYSTEEL112KSI Fsu .
APPLICABLEDOCUMENT: MS90353

Shear strength
Material Protective finish (psi) min
,

Alloy steel Cadmium plate 112,000

TABLE I. Rivet configuration.

l:ml~d’1
.272 .070
.156
.250 .062 .
.332 .135
.188
.305 .125 ,
.432 .140
.250
,400 ,130.
.522 .141
.312
,480 .131
.627 ,205
● 375 K~, •la~
1 I 1 I

6il.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759 w
10 JULY 1979

a-c
.- .
L!40
Clue

Iu
.-
U

s
w
.

x
urn
= . . . —.—... . . . . . . . . . . . . . . . . f---w
. . .N .
- F?----- ------ --

Ixrne u)@ hatno- Nmeulw

a.c
.- 00000 000 --- -----
Lnmolnm LnlriulmLn mmmulln
L:o Oooyo 00000 Oaooo
avc Ill t 11118111 31

. . . . . . . . . . . . . . .
--..-

w
m
cm . . . . . . . . . . . . . . .
L
I
n
.-
&
I

611.2
.. .
-!
 Downloaded from http://www.everyspec.com

MI L-STD-1759
10 JULY 1979

TABLE II. MS90353 Dash numbers. - Continued

.312 Dia I .375 Ofa

Grip range
Gri~
c L dash
Ref no.
Min I Max Max

I
.219‘ .2e2 ,713 .506 -1004 .219 .262 .790 .548 -1204
.281 .345 .775 I .568 -1005 ,281 .345 .853 ,610 -1205
,344 ,407 .838 I .631 ! -1006 .344 .407 .915 ,673 -1206
I
.4061 .470
I
.900 , .693 ! -1007 .406 .470 .977 ,725 -1207
.756 I -1008 .469 .532 1.040 ,798 -1208
.4691 .532 .963
,531 .595 1.025 .818 I -1009 .531 .595 1.103 .869 -1209
,594 .657 1.088 ‘ .881 ! +);: .594 .657 1.165 .923 -1210
.656 .720 1.150 .943 .656 .720 1.227 .985 -1211
I !
,719 .782 1,213 . 1.006 ‘ -1012 .719 [ .782 1.29-J 1.048 -1212
1.275 1.068 ; -1013 .7E1 \ .845 ].353 1.:10 -1213
.781 .845
,8441 .907 1,339 1,131 I -1014 .844 I .9C7 1.415 1.173 -1214
.9061 .970 1.400 1.193 -1G13 :906 ~ .970 1.477 1.235 -1215
1.463 ; 1.256 \ -1016 .969 ~ 1.032 !.540 ;629e -;216
.963 1.032
I
,

1.0311 1.095 1,525 j 1.318 ‘ -10i7 1.031 1,095 i.603 1.36G -1217
1.0941 1.157 1.588 :o~~l -1019 1.094 1.157 1.665 1,423 -1218
1.65: I 1,443 : -1019 1.156 ; 1.220 1.727 1.485 -~2~9
1.156.[1.220 1,548
1.219{ 1.2S2 7.712 !1 ,595 -102!I 1,219 1.2/22 1.790 -122cl
1.281/ 1.345 1.775 i 1.56E ~ -1021 1.281 1.345 1.853 1.610 -1221

1.344 1.407 ;.!338 ! 1.531 -:022 1.344 ; 1.437 1.915 1.672 -1222
1.40611.470 1,900 ‘ 1,633 ! -:023 1.406 ; 1.470 1.977 1,735 -1223
1.4651 1.532 1.963 1,756 ~ -1024 1.469 I 1.532 2.940 1.798 -;224

1.5311 1.595 -1025 1.531 1.595 2.103 1.860 -1225

I
1.5941 1.657 2.080 1.!381 ‘ -1026 1.594 ‘ 1.657 2.165 1.923 -1226
1.656 1.720 2.150 1.943 -1027 1.656 1.720 2.227 1,985 -1227
1.719 1,782 2.213 2,006 -1028 1.719 1.782 2.290 2.048 -1228
1,781 1.945 2.275 2.068 -1029 1.781 1.845 2.353 2.110 -1229
-1030 1,844 1.907 2.415 2.173 -1230
1.844!1.907 2.338 2.131
,
1.906 1.?70 2.400 2.103 -1031 1,906 1.970 2.477 2.235 -1231
1.96912.032 2.463 3.256 -1032 1.969 2.0:2 2.540 2.298 -1222
2,031 2.095 2.603 ?.360 -12:3
I 2,094 2.157 2.665 2.423 -1234
2.156 2.220 2.727 2.485 -1235

2.219 \2.282 2.790 2.548 -1236

611.3
 Downloaded from http://www.everyspec.com
.

t-
 Downloaded from http://www.everyspec.com

...

MIL-STD-1759
10 JULY 1979

SECTION
612

RIVET,BLIND,HIGHSTRENGTH,PULL TYPE,POSITIVEMECHANICALLOCK,
PROTRUDINGHEAD,ALLOY STEEL 112KSIFsu
APPLICABLEDOCUMENT MS90354

—..
— ..—
—-. — --—

.
—--—
—--—
81111
—.. --—
A J LD

Shear strength
Material Protective finish
(psi) min

Alloy steel Cadmium plate 112,000

TABLE 1. Rivet configuration.

INLILLI
.272 a070
.156
.250 .062
.332 .135
.188
#305 .125
.432 .140
.250
,400 .130
.522 .141
.312
.480 ,131 *

612.1
.
Downloaded from http://www.everyspec.com
.

MI L-STD-1759 .-
10 JULY 1979

I
1“’’”””””””””” ‘“”””””””*
--w--- .-F

VNfn=rui w-amo FNt-)W~W

00000 0000. p---- .
Inu)mmbn ulln LnLnlm Lmnngg g
?y~y~ 00000
11111 11111 I

x
Utu
E . ...* ● ✎ ✎ ✎ ✎ ✎ ✎ ✎ ✎ ✎ ✎
-F---F

x
m
z .. . . . . . . . . . . . . . . .
- I

612.2
 Downloaded from http://www.everyspec.com

.:

--
MIL-STD-1759
10JULY 1979

SECTION
613

RIVET,BLIND,
NONSTRUCTURAL,
100°FLUSHHEAD,CLASS2
APPLICABLEDOCUMENT: MS20605

1==1—
.-—
3-
I

—-
1
I
-.

LA

● 1 I
Shear strength
Material Protective finish (psi) min
1 I

} I I I

TABLE I. Rivet configuration. .

A B
c
Dia Ref

●094 .179 .036

.125 .225 .042
.156 .286 .055
.187 *353 .070
,250 .476 .095

613.1
 Downloaded from http://www.everyspec.com

.:,

MIL-STD-1759
10 JULY 1979
TABLE II. Aluminum alloy 2117.
.094 Diameter. nominal
Mandrel Plaln Serrated

-T-l L
Grip range loaded stern stem
Length F
max Max Dash Dash Dash
Min Max no. no. no.

w_ A03CI A03TI A03U1

A03C2 A03T2 AD3N2
AD3C3 A03T3 A03W3
A03C4 A03T4 A03W4
.125 Diameter,nominal
Mandrel Plain Serrated

1--1-1Grip ranqe L loaded stern stern

Length F
max Max Dash Dash Dash
Min Max no. no. no.
I

,047 .062 .256 AD4C 1 AD4T; I AD4X 1 i

.063 .125 :;;: .316 A04C2 AD4T2 AD4id2

L
.126 .295 .381 A04C3 A04T3 A04W3
.188 :R .357 .443 AD4C4 A04T4 A04h’4
,251 .312 .420 .506 A04C5 A04T5 AE4ti5
.313 .375 .482 .568 A04C6 A04T6 A04;6
.376 .437 .544 .630 AC14C7 A0477 A04W7
.438 .500 .607 .693 AD4C3 A06T8 AD4W8
.156 Diameter,nominal
I I I Mandrel Plain Serrated
L loaded stern stem

h-l
Grip range
Length F
ma x Max Dash Dash Dash
Min Max no. no. nO.
J
.062 125 .274 ‘ .44 ‘ AD5C2 A0572 A05’ri2
126 :250 .399“ .56 AD5C4 A05T4 AD5K4
125i .375 .S24 .59 AD5C6 AI)576 AD5A6
.376 .500 .679 .81 A05CE AE578 AD5A%
.187 E)iameter. nominal

Grip range L
Length F ~
ma x Max Dash Dash } Dash
Min Max

.128 .301 .48

no.
A06C2 %-+m%i-
T
.378
126 .250 .426 .60 AD6C4 A0674 AD6W4
:251 ,375 .551 .72 A06C6 AD6T6 AD6U6
.376 ,500 .706 .84 A06C9 AD6T8 A06W8
.501 .625 .801 .97 AO6C1O A06T 10 AO6U1O
.626 .750 .926 1.10 A06C12 A516T12 A06W12
.751 .875 1.051 1.22 AD6C14 AD6T14 AD6U14

Mandrel Plaln Serrated

Grip range L loaded stern stem
Length F
ma x
t=l= I 1
Max
I
Dash
no.
Dash
no.
Dash
no.

.126 .250 I .447 .65 I A08C4 ADET4 AD8W4

.251 .375 I .572 .?7 AD8C6 AD8:6 AD8U6
.376 .697 .99 AD8C9 ADST3 A08W2
.501
.626
.500
.625
750
I .822
.947
!.02
1.15
AD3C!S
A08C;2
A03T1C! AO8W1O
A08T12 AD8W12
.751 :875 1.072 1.27 AD8C14 A08Ti4 A03U]4
.E76 1.000 1.195 1,40 AD8C16 Ac8T16 A08W16

613.2
 Downloaded from http://www.everyspec.com

--

MIL-STD-1759
10JULY 1979

TABLE III. Aluminum alloy 5056.

.094 Dlameterlnominal

l-l
t41n

:040
Grip
range

.063
M8X

,062
.125
Le\gth
max

,14d
.203
F
Max

.281
,281
-
●
B3T1
B3T2
B3W1
B3W2
.126 ,187 .265 .343 B3T3 B3W3
.188 .250 .32a .405 B3T4 B3W4
.125 Diameter, nominal
Platn
I
T-1
Handrel Serrated
Grlp loaded stern stem
range Lekgth F

Mln Max
max Max Dash
+ no, 1
Dash
no.
Dash
no. I
,047 .062 .17o i .256 B4T1 - B4WI

T
.063 .125 .232 .338 . B4T2 B4U2
.126 .187 .295 .381 i4Tj B4W3
●188 .250 .357 .443 84T4 B4W4
.251 .312 ,420 .506 B4T5 B4W5
.313 .375 .482 .568 B4T6 B4U6
.376 ,437 *544 .630 B4T7 B4M7
.438 i .500 ,607 I .693 B4T8 B4W8
------
.156 Diameter, nomina 1

1 1 [ ,
4
.062 .125 .274 ●44 - B5T2 85142
.126 .250 .399 .56 “ B5T4 B5W4
.251 0375 .524 .69 - B5T6 B5M6
.376 .500 .679 .81 - B5T8 B5U8
,187 Diameter,nominal

h-l
Grip L
range Length
max
Mln Max
Zi7r .128 .301 .4a r -im-
.126 .250 .426 ,60 B6T4 B6M4
.251 .375 .551 .72 .- B6T6 B6U6
.376 .500 .706 .84 . B6T8 B6ki8
.501 .625 .801 .97 B6TIO B6U1O
.626 .750 .926 1*1O B6T12 B6H12
*751 .875 1.051 1.22 B6T14 B6W14
.250Diameter,nominal
Mandrel Plain Serrated
Grlp L loaded stern stern
range Length F
. Max
Mln
.126
Max
.250 .447
Max

.65
Dash
no. I Dash
no.
B8T4
Oash
no.
88U4
.251 .375 .572 .77 - B8T6 B8kJ6
.376 .500 .697 .89 . B8T8 B8W8
.501 .625 .822 1.02 . 88TIO B8H1O
.626 ,750 .947 1.15 88T12 B8H12
.751 .875 1.072 1.27 88T14 B8W14
,876 1.000, 1.]95 1.40 B8T:6 B8U16
 Downloaded from http://www.everyspec.com

MIL”STD-1759
10JULY 1979
TABLE IV. Nickel copper alloy (Monel).

.094OIameter,nominal
I I Mandrel Plain Serrated
Grip L loaded stern stem
range F I
Length
max Max Dash Dash Dash
Mln I Max no. no. no.
.040 .062 .140 .281 M3C1 F13T1 M3U1
.063 .125 .203 .281 M3C2 M3T2 M3W2
.126 .187 .265 .348 M3C3 M3T3 M3M3
*188 .250 .328 .405 M3C4 M3T4 M3W4
.
.125Oiameter,nominal

k EHaE
Grip L
range Length

Mln MiIx
max
‘x
.047

m M4T 1 M4W 1

Ii!!!
Iii
T
.063 M4T2 M4W2
.126 M4T3 M4W3
.186 M4T4 M4W4
.251 .312 .420 .506 M4C5 M4T5 M4U5
.313 .375 .482 .568 M4C6 M4T6 M4W6
.376 ●437 .544 .630 M4C7 M4T7 M4W7
.q)() .607 .693 M4C8 M4T8 M4W8
[ .438
.156Diameter,nominal
Mandrel Plaln Serrated
Grip loaded stern stern
range Lekgth F
max Max Dash Dash Oash “
Mln Max no. no, no.
.062 .125 .274 .44 M5C2 M5T2 M5ki2
.126 .250 .399 .56 M5C4 M5T4 M5W4
.251 .375 .524 .69 M5C6 M5T6 M5W6
,376 .500 .679 .81 M5C8 M5T8 M5W8

.187 Diameter.nominal

l-l
Grip L
range Length
ma x
Mln Max

.078 .128 .301 .48 M6C2 M6T2 M6W2

.126 .250 .426 .60 M6C4 M6T4 M6W4
.251 .375 .551 .72 M6C6 M6T6 M6W6
.376 .500 .706 .84 M6C8 M6T8 M6W8
.501 .625 .801 ,97 M6C1O M6T 10 M6U1O
.626 .750 .926 1.10 M6C12 M6T12 M6W12
.751 .875 1.051 1.22 M6C14 M6T14 M6W14

.250 Diameter.nominal
Mandrel Plain Serrated
Grip L loaded stern stern
range Length F
max Max Dash Dash Dash
Min I Max no. no. no.
.126 .447 .65 M8C4 P18T4 M8K4
.251 .375 .572 .77 M8C6 M8T6 M8W6
.376 .500 .697 .99 M8ca F18T8 M8W8
.501 .625 .822 1.02 M8clo M8TIO M8W10
.626 ●7fo ,947 1.!5 M8C12 M8T12 M8W12
.751 .875 1.072 1.27 M8C14 M8T;4 M8W14
,876 1.000 1.!95 1.40 M8C16 M8T16 M8W15

613.4
 —
Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION
614

RIVETS,BLIND,NONSTRUCTURAL,RETAINEDMANDREL:CLOSED-END,
120°COUNTERSUNK HEAD;ALUMINUM ALLOY
APPLICABLEDOCUMENT: MIL-fl-24243/7

+
-@-
LH v
HOLLOW CORE

+
-9-
I

*
v’
FILLED CORE

Shear strength
blaterial protective finish
(psi) min

Anodize or Hollow Filled

Aluminum
alloy 5056 chemical surface
treatment 16,000 28,000
*

TABLE 1. “Rivet configuration.

D
Nom H
dia

.243
.125 .229
.322
.156 .302
.387
.188 .363

-...
 .
Downloaded from http://www.everyspec.com

.:

MIL-STD-1759
10 JULY 1979

TABLE II. M24243/7 Dash numbers.

Grip Dash nu~be~

L
ran ge Aluminum alloy 5056
Mln Max Mim Max Hollow Core Filled Core

.252 .282 .040 .062 A401H A401F

.317 .347 .063 .125 A402H A402F
,379 .409 .126 .187 A403H A403F
.442 .472 .188 .250 A404H
.504 .534 .251 .312 A405H

.347 .377 .040 .125 A502H A502F

.409 .439 .126 .187 A503H A503F
.534 .564 .251 .312 A505H A505F
.371 .401 .063 .125 A602H A602F
.496 .526 .126 .250 A604H A604F

.621 .651 .251 .375 A606H A606F

614.2
 Downloaded from http://www.everyspec.com

----- MIL-STD-1759
10JULY 1979

SECTION
615

BLIND, NONSTRUCTURAL, RETAINEII MANDREL;

RIVETS,
CLOSED-END, DOMED HEAD;ALUMINUM ALLOY
APPLICABLEDOCUMENT: MIL-fl-24243/6

L++e E

o+
j L-i *
+
,T+7,
HOLLOW CORE
4

+
L

-o- 0

FILLED CORE

f
Shear strength
Material Protective finish
(psi) min
,
Hollow Filled
Aluminum , 5056 Anodize or
16,000 28,000
alloy 1100 chemical surface
treatment 6,000 Not
Specified
i

TABLE 1. Rivet configuration.

I D
Nom H I E I

.248 .046
.125
,224 .026
.328 .06i
.156 .pa~ .041
----
} 1 --- 1

615.1
—
Downloaded from http://www.everyspec.com

.-

MIL-STD-1759
10JULY 1979

TABLE II. M24243/6 Dash numbers.

Dash number
L Grip range Aluminum alloy
5056 1100 5056
Min Max Min Max Hollow core Filled core

●222 .252 .040 .062 A401H - A401F

.285 .315 .063 .125 A402H C402H A402F
.347 .377 .126 .187 A403H - A403F
.410 .440 .188 .250 A404H C404H
.472 .502 .251 .312 A405H -

●300 .330 .050 .125 A502H - A502F

.362 .392 .126 .187 A503H - A503F
- .188 .250 - C504H
.487 .517 .251 .312 A505H - A505F
.315 .345 .063 .125 A602H C602H A602F

,440 .470 .126 .250 A604H C604H A604F

.565 .595 .251 .375 A606H C606H A606F
.690 .720 .376 ●500 A608H -
4

615.2
-)
 .
Downloaded from http://www.everyspec.com

.:,

MIL-STD-1759
10 JULY 1979

SECTION
616

RIVETS,BLIND,NONSTRUCTURAL, RETAINEDMANDREL;
OPEN END, 100°COUNTERSUNK HEAD;
APPLICABLEO(XUMENT: MIL-R-24243/4

DIA7
t
!
H

Shear strength
Material Protective finish (psi) min
-
I
1
I

Aluminum Anodize or chemical 16,000

alloy 5052 surface treatment
or 5056
●

TABLE I. Rivet configuration.

.
w-lJ-.227
.125
I .213

TABLE II. M24243/4 Dash numbers”

I 1
Grip range
L ~ )

Min Max Plin Max 5056 5052

.222 .252 .063 .125 A402 B402

,284 ,314 ,126 .187 A403 -

L

616.1
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

. .

MIL-STD-1759
-.
10JULY 1979

SECTION617

RIVETS,BLIND,
NONSTRUCTURALRETAINEiJ
MANDREL:
OPEN-HID,120°COUNTERSUNKHEAD:ALUMINUM ALLOY
APPLICABLEDOCUMENT: MlL=R=24243/9

DIA J \ J20”

.Shear strength
Material Protective finish (psi) min

Aluminum Anodize or chemical 16,000

alloy 5052 surface treatment
h

TABLE 1. Rivet configuration,

Nom
H
dia

.125 .205
.156 .245
.188 ● 339

TABLE II. M24243/9 Dash numbers.

Dash number
Grip range .
Aluminum
L b
alloy
Min Max 5052

● 375 ● 000 .280 A412

.438 ● 000 .312 A514

.469 .000 .375 A615

.656 ● 000 .625 A621

617.1
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION
618

BLIND,
RIVETS, NONSTRUCTURAL,RETAINEDMANDREL;OPENEND,
120”COUNTERSUNK HEAD;ALLUMINUM ALLOY,CARBON STEEL,NICKEL-COPPER
ALLOY
APPLICABLEDOCUMENT: MIL-R024243/5

-@b-
t
t
.4
*’ H
#

-L

Shear strength
Ilaterial Protective finish (psi) min

Aluminum Anodize or chemical 16,000

alloy 5052 surface treatment
or 5056

Steel Zinc plate or cad- 23,000

C-1006 thru mium plate or
C-lolo phosphate coat

Nickel Zinc coat 29,000

copper
alloy
(Monel)
.

TABLE I. Rivet configuration.

k I i

I .125
.243
.229 I
I .270 I
I .156
- t
-@k--l
I .188
.385
.310 I
618.1
 Downloaded from http://www.everyspec.com

..,

MIL-STD-1759
IOJULY 1979

TABLE 11, M24243/5Dash numbers.

L Grip range Dash number

Aluminum alloy Steel Nickel

Min Max Mfn Max , C-1OO6 copper alloy
5056 5052 C-lolo (Monel)

.231 .253 c040 .062 A401 E401

.253 .295 .063 .125 A402 B4;2 04;2 E402
.313 ●343 .126 .187 A403 B403 0403 E403
.373 ●403 .188 .250 A404 B404 0404 E404
.423 .453 .251 .312 A405 - E405

.216 .286 .040 .125 A502 - E502

.316 .356 .126 .187 A503 - E503
.396 .426 .188 .250 A504 - E504
.536 .566 .251 .375 A506 -

.269 ●330 .063 .125 A602 - E602

.4J9 .480 .126 .250 ~ A604 - E604
.529 .650 .251 ●375 A606 “ . E606
.679 .730 .376 ●500 - - E608
.779 .809 .501 .625 - - E610

-
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION
619

RIVETS, BLIND, NONSTRUCTURAL,

RETAINEDMANDREL;
OPEN END,DOMED HEAD:ALUMINUM ALLOY
APPLICABLEDOCUMENT: MIL=R-24243/10

t--L I

-o-
I H
L

0,:;
s:
)) DIA
r
Q++
-
I
-IL,

Shear strength
Material Protective finish (psi) min

Aluminum Anodize or chemical 16,000

alloy 5052 surface treatment
I J
I 1

Rivet configuration. TABLE II. M24243/10 Dash numbers.

TABLE I.
Dash number
Nom Grip range
H E
dia
L Aluminum
.238 ,030 alloy
.125 Min Max 5052
.262 .040

.037 .375 ,000 .280 A412

.156 “ ::;: A514
.047 .438 ●000 .312
.469 .000 ●375 A615
.656 ●000 .625 A621 ‘
9’88 u
Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

..

>.
MIL-STD-1759
‘1OJULY 1979

SECTION
620

RIVETS,BLIND,NONSTRUCTURAL,RETAINEDMANDREL;
OPEN-END,3D ROMEO HEAD;ALUMINUM ALLOY,CARBON STEEL
APPLICABLEDOCUMENT: MlL=R=242~/3
DIA1 rH

I
Shear strength
Material Protective finish (psi) min
1

Aluminum alloy Anodize or chemical 169000

5052 or 5056 surface treatment
Steel Zinc plate or
c-1OO6 thru cadmium plate or 23,000
C-lolo DhosPhate coat

TABLE 1. Rivet configuration.

1 1
Nom
dia H E

.390 .043
.125 .360 .035
r
.650 .082
.188 .600 .062
“~

TABLE 11. M24243/3 Dash numbers.

r L Grip range

Aluminum alloy
Dash number

Steel
Max Min Max c-1OO6
Min
5056 5052 C-lolo
I

I
I

,252 .040 .125 A402 0402 I D402

,222
.126 .250 A404 B404 D404
.347 .377
.250 ,375 A606 B606 D606
.517 .547
,376 .500 A608 B608 D608
.642 .676
,~ol .625 A61O - D61O
.767 .797
,750 A612 - D612
.892 .922 .626
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

.:

MIL-sTD-175i
10 JULY 1979

SECTION
621

RIVETS,
BLIND,NONSTRUCTURAL,RETAINEDMANDREL;OPEN-END,DOMED HEAD:
ALUMINUM ALLOY,CARBON STEEL,CORROSIONRESISTANTSTEEL
APPLICABLEDOCUMENT: MIL-iV24243/l

DIA1 rH

Shear strength
Material Protective finish (psi) min
L-

Aluminum 16,000
Anodize or chemical ,
alloy 5056
1umlnum surface treatment 11,000
alloy 5052

Steel Zinc plate or 23,000

C-1OO6 thru cadmium plate or
C-lolo phosphate coat

Cres 305 Passivate 38,000

TABLE 1. Rivet configuration.

t I I 1
Nom
H E
dia

.198 .032
● 094 .022
.178
.262 ,040
.125 030
.238 ●

I .156 I :;;; I .047

.037
---
●394 ●LM5
P
,188 045 I
4 .356 .- t

621,1
m
 Downloaded from http://www.everyspec.com
.

-:.

MIL-STD-1759
10 JULY 1979
d

TABLE II. M24243/1 Dash numbers.

L Grip range Dash number ~

Aluminum alloy Steel

Min Max Min Max ! C-1OO6 Cres
5056 5052 C-lolo 305

.202 .232 ●040 .125 A302 B302 D302 - -

.327 .357 .126 .250 A304 B304 D304 - -

.160 ●190 ●040 .062 A401 B401 D401 - -

.222 .252 .063 .125 A402 B402 D402 F40Z G402
.284 .314 .126 .187 A403 B403 D403 F403 G403
.347 ●377 .188 .250 A404 B404 D404 F404 G404
.409 ,439 .251 .312 A405 B405 D405 - -
.471 .501 .313 .375 A406 B406 D406 - -
.596 .626 .376 .500 A408 0408 D408 - -

.244 .274 .040 .125 A502 B502 D502 “ -

.306 .336 .126 .187 A503 B503 D503 . - -
.369 .399 ,188 .250 A504 B504 D504 - -
.494 .524 ,251 .375 A506 B506 D506 - -
.619 .649 ,376 .500 A508 B508 D508 - -

.267 .297 .063 .125 A602 B602 D602 F602 G602

.392 .422 .126 .250 A604 B604 D604 F604 G604
.517 ●547 .251 .375 A606 B606 D606 - -
.642 .672 .376 ●500 A608 B608 D608 - -
.767 .797 .501 .625 A61O B61O D61O - -
.892 .922 .626 .750 A612 - 0612 - -
 —
Downloaded from http://www.everyspec.com

..,

MI L-STD-1759
10 JULY 1979

SECTION622
RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL:
OPEN-END, DOMED HEAD;NICKEL-COPPER ALLOY
APPLICABLEDOCUMENT: MIL-R-24243/2
DIA1 rli

Shear strength
Material Protective finish psi) min

Nickel copper Zinc plate I 29,000

alloy (Monel)
I
TABLE I. Rivet configuration.

Nom
H E
dia
.248 .030
.125 .020
.224
.279 .033
.156 .247 .023
:i39 .050
188 .030
.301
●

.462 .063
.250 ,043
.392

TABLE II. M24243/2 dash numbers.

L Grip range Dash number

Nom Nickel copper
dia Min. Max Min Max alloy (Monel )

.210 .040 .062 E401

.180
●230 .260 .063 .125 E402
.125 .126 .187 E403
● 340 .370
.420 ,188 .250 E404
.390

.290 .320 - ;:;; .125 E502

.360 390 .187 E503
.156 ●

.390 .420 .188 .250 E504

.290 .320 .063 .125 E602

,490 .520 .126 .250 E604
,188 .375 E606
.640 .670 ,251
,740 .770 .376 .500 E608

.520 .125 .250 E804

.490
.250 .376 500 E808
.690 .720 ●

622.1
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

MI L-STD-;759
10 JULY 1979

SECTION
623

RIVETS,BLIND,NONSTRUCTURAL,RETAINEDMANDREL;
OPEN-END, SNAP HEAD;ALUMINUM ALLOY
APPLICABLEDOCUMENT: MlL41-24243/8

I rL7 rH

DIAJ

Shear strength
Material Protective finish (psi) min
1 I
I 1
---
Aluminum Anodize or chemical 16,000
alloy 5052 surface treatment
b

TABLE I. Rivet configuration.

Nom
Dia H E
1 ,

.212 ,043
.125 .046
.218 -
.252 .056
,156 .059
.258
.346 .069
.188 .072
.352

TABLE II. M24243/8 dash numbers.

● 125 .000 .250 .312 A41O

.156 ,000 .280 .375 A512
.000 .312 .406 A613
,188 A619
,000 .500 .593
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

.:.

...
MIL-STD-1759
10JULY 1979

SECTION
624

RIVET, BLIND,NONSTRUCTURAL,UNIVERSALHEAD,CLASS I
APPLICABLEDOCUMENT: MS20604

Shear strength
Material Protective finish (psi) min
I 1
I
Aluminum 2117 26,000
Anodize 24,000
alloy 5056
Nickel copper WWM Carbo-wax or 49,000
alloy (Monel) dry film lube

TABLE I. Rivet configuration.

* 4

Universal head
A D
Dia Di a E

.094 .187 .040

.125 .250 .054
.156 .312 .067
.187 ,375 .080
,250 ,500 ,107
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

TABLE II. Aluminum alloy 2117.

.094 Diameter, nominal
Mandrel Plaln Serratea

F
Grip range L loaded stern stem
Length F
max Max Dash Dash Dash
no. no. no.

.015 .062 .140 .281 A03C1 AD3T1 A03u1

.063 .125 .203 .281 A03C2 AD3T2 A03U2
.126 .187 .265 .343 A03C3 A!13T3 A03u3
.188 .250 .328 .405 AD3C4 AD3T4 AD3M4
.125 Diameter, nominal
Mandrel Plain Serrated
Grip range L loaded stern stern
Length F
max Max Dash Dash Dash .
Min Max no. no, no.

.015 .062 .170 .2S6 A04C1 A04T1 AD4K1

.063 .125 .262 .318 AD4C2 A04T2 AD4ki2 .
.126 .187 .295 .382 AD4C3 AD4T3 AD4U3
.188 .250 .357 ,443 AD4C4 AD4T4 AD4K4
.251 .312 .420 .506 AD4C5 AD4T5 AD41f5
.313 .375 .482 .568 AD4C6 AD4T6 AD4W6
.376 .437 .544 .630 AD4C7 AD4T7 AD4k7
.438 .500 .607 .693 AD4C8 AD4T8 AD4u8
,156 Diameter, nominal
Mandre1 Plain SerrateO
Grip ranqe 1. Ioaaed stern stern
Length F
max flax Dash Dash Dash
Yin Max no. no. no.

.015 .125 .274 .44 AD5C2 AD5T2 AD5kJ2

.126 .250 .399 .56 AD5C4 A05TA AD5id4
.251 .375 .524 .65 A05C6 A05T6 AD5k6
.376 .500 .679 .81 A05C8 AD5?8 A05u8

.187 !)iameter.nominal
Serrated
stem

Dash
nO,

.015 .125 .301 ,48 AD6C2 A06T2 AD6i{?

126 .250 .426 .60 A06C4 AD6T4 A06bi4
:251 .375 .551 .72 AD6C6 AD6T6 AD6U6
AD6C8
.
.376 .500 .706 .84 A06T8 AD6U8
.501 .625 .801 .97 AO6C1O AD6TIO AD6H1O
.626 .750 .926 1.10 A06C12 AD6T12 Ao6k’12
.751 .875 1.051 1.22 AD6C14 AD6T14 AD6U14

.250 Diameter. nominal .

Mandrel Plain Serrated

I Grip ranqe L

-H stern stern
loaded
Length F
ma x Max Dasn Oash Dash
j Min J Max no. no. no,

.015 .343 .52 AD8C2 AD8T2 A08ri2

.126 :;;; .447 .65 AD8C4 A08T4 AD6ii4
.251 .375 .572 .77 A08C6 A08TG ALW’6
,376 .500 .697 “9 hc)sce AOETS AD8w
.501 .625 .822 1:;2 AD8C1O AD8T10 aD8k Io
.626 .750 .947 1.15 AD8C;2 h08T?2 A08ii12
.751 .875 1.072 1.27 A03C 14 Ao&T14 AO% 14
.!?76 1.000 ‘1.195 1.$0 AD8C ?6 AD6T!6 AD8U16

624.2
.. I
Downloaded from http://www.everyspec.com

MI L-sTD”1759
10JULY 1979

TABLE 111. Aluminum alloy 5056,

.094 Dtmeter, nominal
-
Plain Serrated
stern stem
Grip range L
Length F
max Max Dash Dash
Min I H&x no. no.

.01s .062 .140 .281 B3T1 03ul

.063 .125 .203 .281 8372 B3U2
.126 .187 .265 .343 B3T3 B3M3
.188 .250 ,328 .405 B3T4 B3U4
.125 Diameter, nominal
Plaln Serrated
Grip range L stern stam
Length F
max Max Dash Dash
Mifl Max no. no.

.01s .062 .170 .256 8411 B4141

.063 .125 .232 .318 B4T2 B4U2
.126 .187 .295 .381 B4T3 B4N3
.188 .250 .357 .443 B4T4 B4U4
.251 .312 ,420 ,506 B4T5 B4U5
.313 .375 .482 .56B B4T6 B4U6
,376 .437 .544 .630 B4T7 B4U7
.438 .500 .607 .693 B4T8 B4U8
b
.156 Diameter, nominal
Plain Serrated
Grip range L stern stern
Length F
max Max Dash Dash
Hln Max no. no.

.015 .125 .274 ,44 B5T2 B5U2

;;;: .250 .399 .56 9ST4 B5W4
.375 .524 .69 EIST6 B5W6
.376 .500 ,679 .81 B$T8 B5U8

.187 Oiafwter, nominal

Plain Serrated
GriD range L stem stem
Length F
max Max Dash Dash
Hin M8X no. no.

.015 ,125 .301 ,48 B6T2 B6W2

.126 .250 .426 .60 B6T4 B6U4
.251 .375 .551 ,72 B6T6 B6W6
.376 .500 .706 .84 .B6T8 86H8
●501 .625 .801 .97 B6TIO B6U1O
.626 .750 ,926 1.10 B6T12 B6U12
.751 .875 1.0s1 1.22 B6T14 B6U14

.250 Diameter, nomnal

Plain Serrated
GriD range L stem stem
Length F
max Max Dash Dash
Mfn Max no. no.

.Ql~ .125 .342 .52 B8T2 B8W2

.126 .250 .447 .65 BBT4 B6W4
.251 ,375 .572 .77 B8T6 88W6
.376 .500 ,687 .89 B8T8 9BW8
.501 .625 ,822 :.02 B8TIO B8W1O
.626 .750 ,947 1.15 B8T12 B8W12
.875 1.372 1.27 B8T14 88W14
:/% 1.Ooc’ 1.!95 1.40 B8T16 B8U16
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE IV, Nickel copper alloy (monel).

.094 Diameter, nominal
I I I Mandrel Plain Serrated
L loaded stem stem

hi
Grip range
Length F
max Max Dash” Dash Dash
Min Max no. no. no,

.01s .062 .140 .281 M3C1 M3T1 M3U1

.063 .125 .203 .281 U3C2 M3T2 M3U2
.126 .187 .265 .343 M3C3 M3T3 M3U3
.188 .250 .328 .405 M3C4 M3T4 M3U4
,
. 175
--- Diameter.
- . - - -- , nofrnnal
- -
Mandrel
I Plain Serrated

$i-
Grip range L loaded stern stem
Length F
max Flax Dash Dash Dash
M{n Max no. I no. no.

.015 .062 .256 M4C1 144T 1 M4U1

.063
.126
.125
.187
::;!!
.295
,318
.381
M4C2
!44C3
M4T2
M4T3
M4U2
M4U3
.188 .250 .357 ,443 M4C4 n4T4 H4W4
.251 .312 .420 .506 M4C5 M4T5 M4U5
.313 .375 .482 .568 M4C6 M4T6 M4W6
.376 .437 .544 .630 M4C7 M4T7 M4U7
.438 .500 .607 .693 I’ibce M4T8 M4U8

.156 Diameter, nominal

Plain ‘ Serrated
stern stern

Dash Dash -
+no. no.

J
.015 .125 ,274 .44 M5C2 M5T2 M5U2
.126 .250 .399 .56 M5C4 Y5Tt M5W4
,251 .375 .524 .69 M5C6 M5T6 M5ii6
.376 .500 ,679 .81 M5C8 M5T8 M5u8

,187 Diameter, nominal

Mandrel Plain Serrated
Grip range L loaded stem stern
Length F
max Max Dash Dash Dash
Min Max no. no. no.

T
.015 .125 .301 .48 M6C2 M6T2 M6H2
,126 .250 ;:;: .60 M6C4 M6T4 M6U4
.251 .375 .72 M6C6 M6T6 M6U6
.376 .500 .706 I .84 M6C8 M6T8 M6U8
.501 .625 .801 .97 M6CI0 M6T 10 M6U1O
.626 .750 ,926 1.10 M6C12 M6T12 M6U12
.751 .87!i 1.051 1.22 M6C14 M6T14 M6U14

.250 Diameter, nominal

Mandrel Plain Serrated

Grip range L loaded stern stem
Length F
max Max Dash Dash Dash
Min I Max no. no, no.

,015 .12s .342 .52 M8C2 M8T2 M8u2

1
.250 ,447 .65 M8C4 M8T4 M8W4
:;:! .375 .572 .71 M8C6 M8T6 M8W6
.376 .500 .697 .89 M8C8 M8T8 M8U8
.501 .625 ,822 1.02 M8c 10 M8T 1(J M8WI0
.626 .750 .947 1.15 M8C12 M8T12 M8u12
,751 .875 1.072 1.27 M8C14 M8T14 M8U14
.876 1.000 14195 1,40 M8C16 M8T16 M8U 16

.-..
 w
Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION 625

RIVET-BLIND,
PROTRUDINGHEAD,LOCKED SPINDLE
APPLICABLEDOCUMENT: NAS1398

rFl

Shear strength
Material Protective finish
(psi)

Aluminum
,5056F Anociize or chemical 16,900 to SI,G50
alloy
017TA surface treatment 21,350 to 40,275-
Nickel copper None or cadmium 31,000 to 41,625
alloy (Monel) plate or silver
Cres A286 . plate 42,200 to 79,250

TABLE 1. Rivet configuration.

A
Rivet
Rivet
6. E dia
size
Dia number
nom
di~

.125 .250 .054 4

.156 .312 .067 5
.190 .375 .080 6
.250 ,500 .107 8

# f’ A --- .
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

TABLE II. NAS1398 Dash numbers.

.

NAST398 ( )4 .125 Dia NAS1398( )5’.156 Dia

~ Grip
Grip range L- Grjp range
Length F Length F ::sh
Min Max max Max Min Max max Max ‘

.025 .062 .198 ●39 .031 .062 .201 ,38 1

.063 .125 ●260 .51 .063 .125 ,263 ●49 2
.126 .187 .323 .63 .126 .187 .326 .61 3
.188 .250 .385 ●75 .188 .250 .388 ●73 4
.251 .312 .448 .87 .251 .312 ●451 .85 5

,313 ,375 .510 .98 .313 ●375 .513 .97 6

.376 .437 .576 1.09 7
.438 ●500 .638 1.20 8
9
- 10

- 11
12 .
13
. 14 ,

NAS1398( )6 .190 Dia NAS1398( )8 .250 Dia

Grip range L Grip range L Grip

4 F Length F clash
Length
Min Max max Max Min Max max Max no.

.037 .062 .225 ●44 - - - 1

.063 .125 .287 ●55 .063 .125 .323 .57 2
.126 .187 .350 .67 .126 ,187 .385 .69 3
.188 .250 .412 ●79 .188 .250 .448 .81 4
.251 .312 ●475 .91 .251 .312 .510 .93 5

.313 ,375 .537 1.03 .313 .375 .573 1.04 6

.376 ,437 .600 1.15 .376 .437 .635 1.16 7
.438 ,500 .662 1.27 .438 ●500 .698 1.28 8
.501 .562 .725 1.44 .501 .562 .760 1.46 9
.563 .625 ,787 1.56 .563 .625 .823 7.58 70

.626 .687 .850 1.68 .626 .687 .885 1.70 11

●688 .750 .912 1.81 .688 ,750 .948 1.83 12
- .751 .812 1.010 1.95 13
- .813 .875 1.073 2.07 14

6?5.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION
626

RIVET-BLIND,
PROTRUDINGHEAD,
MECHANICALLYLOCKED SPINDLE,
BULBEO
APPLICABLEDOCUMENT: NAS1738

Shear strength
Material protective finish
(psi) ‘

Aluminum 5056 Anodize or chemical 28,900 to 50,500

surface treatment

I Nickel copper
allov (Monel)
None or cadmium
t)late I 38,300 to 73,000
I
TABLE 1. Rivet configuration.
I
A B
Dia Dia E

●140 .250 .054

.173 .312 .067
.201 .375 .080

TABLE II. NAS1738 Dash numbers.

NAS1738 ( ) 4 (.125 O]A) NAS1738 ( ) 5 (.156 DIA) NAS1738 ( ) 6 (.1980[A)

Grip range L Grip range L Grip range L Grip

Length F Length Lenqtn F dash
HIn Max mdx k!d X Mln Md a max I ix Mir Ma.I max Max no.
I
.020 .062 .219 .38 .025 ,062 .250 .42 .03C
I
, .062 .281 .45
.063 .125 .281 ,(4 .063 .125 .312 .48 .063!.125 .344 .51 :;
.126 .187 ,344 .50 .126 !187 .375 .54 .126 .406 .58 -3
.188 .250 .406 .57 .250 ,437 .60 188 i :;;: .469 .64
:;:;
.251 .312 .469 .63 .312 .500 ! .67 I :25; ; .312 .531 .70 ::
. . . .313 .375 1
4 - .562 ~ .73 .313 I .375 .594 .76
. . .
.376 ‘ .437 .656 .83 :!
. . .
.436 .500 .719 .89 -8
-i: : ~ ‘“ ~: t

626.1
 Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759
10JULY 1979

SECTION
627

RIVET,BLIND,
“STRUCTURAL,PULL STEM,SELF-PLUGGING,
100°FLUSH HEAD,TYPE IICLASS2
APPLICABLEDOCUMENT MS20601

r ‘axl=GF— GRIP
RANGE
c
@ ~ jr
-. -- —--~
I I I
.~

1
1- .- -- --

100°
%- /~-1- A
v
Shear strength
Material Protective finish
(psi) min

Aluminum 2117
k%-
F
Anodize
allo 5056 1
Nicke copper P1aln or 49,000
alloy (Monel) cadmium plate
I

TABLE I. Rivet configuration.

A -
Rivet
size B c
nom Dia Ref
Dia

.125 .225 .042

.156 .286 0055
,188 ●353 .070
.250 .476 .095

627.1
 Downloaded from http://www.everyspec.com
.

...

MIL-STD-1759
10JULY 1979

TABLE II. With serrated stem.

,125 Rivet diameter,
nomlndl
,
2117 Al 5056 Al !bne I

Grip ranae L

I I
Length F Dash 13ash Dash Chsh
Hfn Max mm Max no. no. no. no.

up to’ .062 .1?0 .500 A04dl B4U1 M4U1 MP4UI

.063 .125 .232 .562 AD4U2 B4U2 J4U2 MP4U2
.126 .187 .295 .750 AD4k; B4W3 M4U3 MP4U3
.188 .250 .357 .812 A04u4 04u4 H4U4 UP4U4
.251 .312 .420 1.010 AD4u5 B4uS H4U5 UP4U5
.313 .3?5 .482 1.072 ADbd6 B4U6 M4U6 MP4U6
.376 .437 .54s 1.197 Ao4d7 B4U7 )44U7 nP4u7
.438 .500 .607 1.322 Ao4ii8 B4u8 M4U8 HP4U8
.501 .562 .670 1.509 A04U9 B4U9 M4W9 MP4U9

.156 Rivet dfemeter, nomnal

2117 Al 5056 Al
L
Length F
I Max
Oastl Dash
Mn max Max no. no.

. 06S .125 .254 .620 Ao5k2 e5u2 H5U2 HP51i2

.126 .187 .317 .808 A05G3 B5U3 m% 3 MP5M3
.188 .250 .379 .070 A05U4 B5U4 M5U4 uP5d4
.251 .312 .441 1.058 A05N5 B5U5 HSU5 MP5K5
.313 .375 .s03 1.120 AC5U6 B5u6 I15U6 MP5a6
.376 .437 .567 1.339 A05k 7 85U7 M5U 7 HP5W
.438 .509 .629 1.401 A05U8 B5U8 M5U8 !!P5!i8
.501 .562 .692 1,567 A05R9 B 5U9 N5U9 nP5h9
.625 .754 1,630 Ao5ulo B5u1O M5!X’1O Mp$u]c
.563
.626 .687 .817 1.817 A05iil ; B5W11 M5h 11 MP5hl 1
.688 .750 .B79 1.880 A05u 12 B5ii12 I!stil 2 MP5h12
.751 .812 .942 2.067 A051i13 B5w: 3 M5U13 HP5M13
.813 .875 1.004 2.130 AD5U14 B5w14 !45G14 MP5d14

.188 Rfvet dixmeter, nannnal

12117A1 I S056A1 l~nel lA40nel, caanlumpltted

Gr!p risnqe “1 I I
F Dash hsh Oash Dash

m
%s x no. no. no, no.
m’ ‘~:th

.700 A061i2 B61i2 146h2 MP6H2

.888 A06M3 B6U3 t461i3 HP6ti3
.950 AD6M4 B6h’4 m6ii4 MP6d4
1.138 AD6k5 B6d5 M6xi5 MP6k5
.313 .375 .527 1.200 A06U6 B6ii6 M6U6 HP6n6
.376 .437 I .590 1,419 A06k? B6N7 M.6n ? MP6ti ?
.438 .Socl .652 1.481 Ao6d8 B6ti8 H6U8 MP6ii8
.501 .562 .715 1.637 A06w9 B6U9 M6w9 MP6U9
.563 .625 .777 1.699 AO6U1O B6U1O M6KIC MP6id10
.626 .687 . B40 1.887 AD6n 1 ; B6U11 H6h11 MP6kJlI
,688 .750 .902 1.949 A06H12 B6U12 M6hi 12 MP6#12
.751 .812 .965 2.074 Ao6!i I 3 B6U13 M6U13 MP6k 13
.813 .875 1.027 2.199 AD6w 14 B6U14 !!6U14 MP6u14

.250 Rtvet dfemeter, nominal

I 2117 Al 5056 Al

Grip ranae I L
F Oash Oash
M n ma x no. no.
=
.125 ,187 .385 .968 AD8ii3 BW3 IW3 MP8N3
.188 .250 .447 1.030 A08U4 B8w4 MIJUA MPW4
.251 .312 .510 1.218 A08W5 B8U5 M9U5 HP8U5
.313 .375 .572 1.280 A08U6 88U6 t4Bu6 MPBW6
.376 .437 .635 1.468 Aoak 7 9BU7 Wii 7 MPIJW7
.438 ,500 .697 1.530 Ao8ii8 88U8 M8k8 MP8aJ3
.501 .562 .760 1.718 AW9 B8U9 M8h9 MPeu9
.563 ,625 .822 1.780 A08Mlil BWIO Mfjk10 MPW1O
.626 .687 .885 1. 96B AD8U11 8BU11 M8U 1 I Mv@#ll 1
.688 .750 .947 2.030 A08W 12 B8U12 58W 12 MPBIN12
.751 .812 1.010 2.218 A08U I 3 98U13 n@si13 MP@li13
.813 .875 1.072 2.290 A08U 14 B8U14 /48u 14 MPRk14
.876 .937 1.134 2.405 A08U I 5 a8U15 Y8M 15 14P8U 15
.938 1.000 1.198 2,530 A08U16 B8U16 Wk 16 MP81i16

627.2
f .--
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION628

RIVET,
BLIND,STRUCTURAL,PULL STEM,SELF-PLUGGING,
PROTRUDINGHEAD,TYPE I
Applicable
DOCUMEltT:
NS20BO0

E o-G~lp-

1 RANGE

Shear strength
Material Protective finish
(psi) min

Al uml num 2117 26,000

Anodize 24,000
alloy 5056
Nickel copper P1aln or Cadmium 49,000
alloy (Monel) plate

TABLE 1. Rfvet configuration.

A
Rivet Universal head
size
nom
dia
D
Dia I E

.125 .250 ●054

.156 .312 . .067
.188 ●375 .080
,250 ●500 .107

●
H’
-b -’, 628.1
 Downloaded from http://www.everyspec.com
.

.:.

MIL-STD-1759
10 JULY 1979

TABLE II. With serrated stem.

,125 Rfvet dluneter, nomlntl

2117 Al 5056 Al Mmel Monel, ct@nlum pitted

Grip range L
Length f Oash Dash Dash Dash
Min Mm m4x ma no. no. no. no.

up to .062 .170 .500 AD4U\ B4U1 H4U 1 MP4U1

.063 .125 .232 .600 AD4V2 B4U2 H4U2 PIP4u2
.126 .187 .295 .750 A041113 B4U3 H4U3 MP4143
.188 .250 .357 .050 A04W4 B4u4 n4k4 HP4i/4
.251 .312 .420 1.010 A04U5 B4W5 M4U5 MP4MS
.313 .375 .482 1.100 A04U6 b4W6 M4U6 MP4U6
.376 .437 .545 1.197 A04u7 04u7 n4u7 W4U7
.438 .500 .607 1.322 A04U8 B4u8 M4U8 MP4U8
.501 .562 .670 1.509 AD4W9 B4U9 f441i9 MP4U9

.156 Rtvet dfameter, nominal

2117 Al 5056 Al bne 1 HOnel, catilum plated

Grfo range L
length F tush Oash 03sh Oash
Mtn Ha x I max Ha X no. no. no. no.

up to .062 .192 .558 A05UI B5u1 M5W HP5H1

.063 .125 .254 .620 AD5ti2 85W2 H5U2 MP5U2
.?26 .187 .317 .808 A05U3 B5U3 !15U3 HP5U3
.188 .2s0 .379 .870 AD5M4 B5W4 H5U4 MP5U4
.251 .312 ,441 1.058 A05u5 B 5U5 M5U5 HP5U5
.313 .375 .503 1,120 A05W6 B5U6 M5U6 MP5k6
.376 ,437 .567 1,339 A05U7 B5W7 H5U7 14P5U7
.438 .503 .629 1,401 AD5U8 B5U8 U5U8 MP5u8
.501 .562 .692 1.567 A05w9 B5U9 M5M9 MP5W9
.563 .625 .754 1.630 AD5U 10 B5w1O M5W1O MP5W1O
.626 .6B7 .817 1.817 AD5H11 E5U11 )15U11 ?4P5H11
.688 .750 .079 1.880 A05d12 B5U12 H5W12 fqp~wlz
.751 .812 .942 2.087 A05U13 B5H13 n5bfl 3 MP5!dl 3
.813 .875 1.004 2.130 A05w14 BSU14 M5M14 W5U14
.
, nominal

2117 Al 5056 Al I bne I

Grip range L
Length F Oash Oash Oash OMh
Wn Ith. max Max no. no. I no. no.
,
up to .062 .215 .638 A06U1 86U1 M6bl 1 rnp~~l
.063 .125 .277 .700 A06u2 B6k2 H6W2 MP6h2
.126 .187 .340 .808 A06U3 B6W3 M6U3 MP61i3
.188 .250 .402 .950 A06b14 B6i44 H6M4 MP6u4
.251 .312 .465 1.138 A06U5 B6W5 y6u5 MP6W5
.313 .375 .527 1.200 AD6M6 B6n6 M6U6 HP6ti6
.376 .437 . S90 1.419 AOW7 B6H7 M6U7 HP6U7
.438 .500 .652 1.481 A06U8 B6U8 H6U8 HP61i8
.501 .562 ,715 1.637 A06W9 B6U9 H6U9 MP6ti9
.563 .625 .777 1.699 Ao6H1O 86WI0 M6U 10 MP6k10
.626 .687 .840 1.887 A06W11 B6U11 W/l 1 HP6dll
.6B8 .750 .902 1.949 A06U12 B6U12 M6U12 FIP6U12
.751 .812 .965 2.074 A06U13 B6U13 MU13 llP6bl13
.813 .875 1,027 2.199 A06U14 B6U14 M6W14 MP6h14

m=
.250 Rivet d{amter, nom+nal

2117 Al 5056 Al Mone I

Grip range L
Length F Oash Oash Dash hsh
mbx Max no. no. no. no.

125 .187 .385 .970 A08U3 B8u3 MW3 MP8U3

.250 .447 1,090 A08U4 88u4 li8u4 HP8U4
;: .312 .510 1.220 AD8M5 B8U5 H8H5 MP8U5
313 . 3?5 .572 1.340 A08U6 B8U6 M8146 MP8U6
376 .437 .635 1.470 A08U7 B8U7 H8h 7 MP8k’7
438 .500 .697 1. S90 A08U8 B8U8 IW8 MP8U8
501 .562 .760 1.720 A08u9 B8U9 MBU9 MP8bf9
.563 .625 .822 1.840 AO8U1O B8W1O WJulo MP8W1O
.626 .687 .885 1.970 A08U11 98U11 Mull MP8W11
.688 .750 .947 2.090 A08U12 B8M12 new 12 HP8u12
,751 .812 1.010 2.220 A08U13 B8W13 MM413 MP8u I 3
.813 .875 1.072 2.340 A08U14 B8U14 M8M14 HP8u14
,876 .937 1.134 2.405 A08w15 88U15 M8W15 ~9~J5
.938 1.000 1.196 2.530 A081416 B8U16 MW16 NP8u16

628.2
 Downloaded from http://www.everyspec.com

..
MIL-STD-1759
10JULY 1979

RIVET,
BLIND-UNIVERSAL
HEAD,DRIVETYPE
APPLICABLEDOCUMENT: MS24662

-L-tBt
.

AJ
.
GRIP
—

Material Protective finish

Shear strength
(psi) min

A7uminum ,2117-T4 Anodized 26,000

alloy 5056-H32 Plain 24,000
Carbon steel
I Cadmium plate 32,000
●

67Q .1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

TABLE I. Rivet configurationdash numbers.

MS24662 Dash no.

B D Grip range Alumlnum

Head Head L Carbon
O:a height diameter e Mln Max Length 2117 50S6 stool

.046 .078 .1S6 170

.079 .109 .188 ; 171 :
.110 .140 .219 172
.141 .171 .250 ; 173 1!
.172 .203 .201 11 174 12

.125 .054 .2s0 .204 .234 .312 13 175 14

.235 .265 ,344 15 176 16
.266 .296 .375 17 177 18
.297 .328 .406 178 20
.329 .359 .438 ;: 179 22

.360 .390 .469 23 180 24

.391 .421 .500 25 181 26

.046 .078 .188 182 28

.079 .109 .219 :; 183 30
.110 .140 .250 31 184 32
.141 .171 ,281 33 185
.172 .203 .312 35 186 ::

.204 .234 .344 37 187 38

.235 .265 .375 39 188 40
.266 .296 .406 41 189 42
.297 .328 .438 43 190 44
.156 .067 .312 ..329 .359 .469 45 191 46

.360 .390 .500 47 192 48

.:91 ,421 .531 49 193 50
.422 ,453 .562 51 194 52
.454 .484 .593 53 195 54
.485 .515 .625 55 196 56

.516 .546 .656 57 197

.547 .578 .688 59 198 X
.579 .609 .718 61 199 62
.610 .640 .750 63 200 64

.046 .109 .250 150 201 221

.110 .171 .281 151 202 222
.172 .234 .344 152 203 223
.235 .296 .406 153 204 224
.297 .359 .469 154 205 225
.188 .080 .375
.360 .421 .531 155 206 226 .
,422 .484 .594 156 207 227
.455 ,546 .656 157 208 228
.547 .609 .719 158 209 229
,610 .671 .781 159 210 230

.046 .109 .250 160 211 231

.110 .171 .281 161 212 232
.172 .234 .344 162 213 233
.235 .296 .406 163 214 234
.297 .359 .469 164 215 235
.250 .107 .~of)
.~6(3 .531 165 216 226
.:21
.422 .484 ●gd 166 217 237
.485 .546 .656 167 218 238
.547 .609 ,719 168 219 239
0610 .671 .781 169 220 240

629.2 )
<-.
4:.
 Downloaded from http://www.everyspec.com

..

MI L-STD-1759
10 JULY 1979

SECTION701

PIN,100°CSK,HEAD
HI-SHEARRIVET,CLOSE TOLERANCE,1200”F
APPLICABLE
DOCUMENT:NAS1583

(Max Grip+B) J
h

(’
B
r-

100°

\/lVA ~ ~—.
“
Shear strength
Material Protective finish
(psi)

Passivate 83,000 to 96,000

Inconel - X

Table I. Rivet configuration dash numbers.

Al First
Nom
Min
B. H dash
dia Ref no.
ref 1

I
.125
●188
.1787
.2578
.083
.125
.0354
.0485
I -4
-6
.250 ●3504 .165 .0631 -8
.312 .4289 .206 .0704 -10
.375 .5149 .248 .0810 -12

NOTE : Second dash number (See NAS1583) designates

maximum grip in 1/16 Of an inch increments
up to ani including one inch.

d-l 701.1
Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

-...
MI L-STD-1759
10 JULY 1979

sECTION 702

PIN,FLAT HEAD
H 4HEARRIVET,CLOSE TOLERANCE, 200°F
APPLICABLEDOCUMENT: ?IAS15M

H B
I it- rl

f
Shear strenqth
Material Protective finish
(psi)
. .
I
I
1 I
passivate 83,000 to 90,000
Inconel-x

TABLE I. Rivet configuration dash numbers.

A First
Nom B dash
Min H
dia Ref no.
●
ref

.208 .039 -.
.125 .083
,188 .029
.315 “ J*5 .055 +
.188 .045
.295
.412 .069 -8
.250 .165 .059
.387 ~
505 .078
,312
●

.206 -lo
.475 *068
.600 088
,2Q8 -12
●

.375 ,078
.565

NOTE : Second dash number (see NAS1584) designates

maximum grip in 1/16 of an inch increments
up to and including one inch.
. . 7n9 1
Downloaded from http://www.everyspec.com

4
 Downloaded from http://www.everyspec.com

.
MIL-STD-1759
10 JULY 1979

SECTION 703

STEEL
RlVET400°COUNTERSUNKHEMICORROSIONRESISTANT
APPLICABLEDOCUMENT:AN 124951THRU AH125100

v
Shear strength
Material Protective finish (psi) min

Cre5 Not specified

Not specified 1
18Cr-8Ni

TABLE 1. Rivet confiqurat on part numbers.

L
Dia A B c Length

.188 AN124952
.250 AN124953
.312 AN124954
.105 .022 .116 .375 AN124955
,062 AN124956
.438
.500 AN124957
.562 AN124958

.250 AN124971
,312 AN124972
.375 AN124973
,094 .170 ,036 .169 .438 AN124974
.~oo AN124975
.562 AN124976

.312 AN124990
.375 AN124991
.216 .042 .225 ,438 AN124992
.125
a500 AN124993
.562 AN124994
AN1250W
AN125019I
.!56 .273 i ,C55 AN125011I
I AN125012I
i !
1
.438 AN125023I
t .188
i
.344 I .373
i 13g .:90 AN1ZS029
C52 AN12Y3:CI
I

7n~ 1
Downloaded from http://www.everyspec.com

ad
 Downloaded from http://www.everyspec.com

-...
MIL-STD-1759
10JULY 1979

SECTION 704

COUNTERSUNK HEAD HI-SHEAR

RIVET-lOOO
CLOSETOLERANCEHEADAND SHANK
APPLICABLEDOCUMENT: NAS525
(MAX GRIP + B)

~—

..

Shear strength
Material Protective finish (psi) min

t &
Cadmium plate 95,000
Alloy steel I J
lumbers.
TARI F ~.
1r8ub- -- Rivet configuration dash r
I
.Vu.
Gr40 ranae

.126
~A’l~lH}Ninl~x” m%’%.
IQ
1 )

1 I I I nc9 I .125 -4-2

.188 .4-3

II ; ;:;

.313

.376
.439
.250
.312
.375

.438
.500
-4-4
.4-5
-4-6

-4-1
-4-8
,501 .562 -4-9
.563 .625 -4-1o
.626 .688 -4-11

.689 . 7s0 .4-12

.151 .812 .4.13
.813 .875 -4-14
.93d -4-15
I 1- 1
.816
.939 I.m -4-16

1.W1 1.062 -4-17

1.063 1.1:5 -4-18
125 035 1.126 1.188 -4-19
I ,189 1.250 .4-20
I 1.251 1.312 .4-21

I 1.311 1.375
1.438
-4-22
-4-23
1.176
1.439 1.50Q .4-;4
, .4-:5
11.501 1.562
I
I
I
II >61 1.625 -4-26
I
-4-27
I 11.688

I
I ii i 1.626
‘ I 689
I :5)
~l.:so
1.s1:
A-28
-4.29
I 1 I.dll 1.d75 .4-jO
..I.JI
! 1.376 1 .33s
I I
2. coo -J- 32

,I
2,062 .4-1]
1 :.1:5 .4.14
Z. :81Y .4-]5
I

I L
.● . ●
. 5O .4-j6
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

0
v

●✍

u
-!
2
t-

72
!&)
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

.
o-w
mubnyr- a3m---

&o&oo
.F-e-
r3&AA&
v.?----
11111 11111 I till

w
E.

-u

0 m
.

,
ino
NC
n
as
<al
Zu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ;
----- -H ..- m- $-.W-(N tw(NmJmJ

. . . . . . . . . . . . . . . . . . . . . ..... 0.,, .,

# dmwddH- d. H--- dw - ArJnl(w

0
m
Cu
 Downloaded from http://www.everyspec.com

MI L-STD-1759
10 JULY 1979

TABLE I. Rivet canfiauration dash numbers. - continued

A1 B Ii NAS525
Dash no.

.189 .250 -12-4

.251 .312 -12-5
.313 .375 -12-6
.376 .438 -12-7
.439 .500 -12-8

.501 .562 -12-9

.563 .625 -12-10
.626 ●688 -12-11
.689 .750 -12-12
.751 .812 -12-13

.813 .875 -12-14

.876 .938 -12-15
939
● 1.000 -12-16
1.001 1.062 -12-17
1.063 1.125 -12-18

1.126 1.188 -12-19

1.189 1.250 -12-20
.375 .515 .081 1.251 1.312 -12-21
1.313 1.375 “-12-22
1.376 1.438 -12-23

1.439 1 500
● “12-24
1.501 1.562 -12-25
1.563 1.625 -12-26
1.626 1.688 -12-27
1.689 1.750 -12-28

1.751 1.812 -12-29

1.813 1.875 -12-30
1.876 1.938 -12-31
1.939 2.000 -12-32
2.001 2.062 -12-33

2.063 2.125 -12-34

2.126 2.188 -12-35
2.189 2.250 -12-36
4

Note: NAS525-4 thru -12 rivets to be installed

with NAS528 collars of the same dash
number (see section 202).

704.4
c,- A
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION 705

RIVET-lOO”
COUNTERSUNK HEAD,MILD STEEL
APPLICABLEdocument: AS125101THRUASI2525O

.
v
Shear strength
Material Protective finish (psi) min

Carbon steel Cadmium plate Not specified

AMS7225

TABLE 1. Rivet configuration part numbers.

I I
! Part no.
old A B c Le;gth

. 18s AS125102 :
.250 AS!25i03
.312 AS12510:[
.105 .022 .375 ASl?Slo5
‘.062 .438 X125106
.500 AS125107
.562 , AS1251C8
I
.250 AS125i21

d-
.312 AS125122
.375 ASi25123
.094 .170 .036 .14i .438 .AS125124
.500 4S125125
.562 AS125126

.250 AS125139
.312 AS125140
.375 AS125141
.125 .216 .042 .188 .438 AS125142
.500 AS125i43
.562 A$i25i44 I

lc-
0
.,. .272 .355 .:34

.21?l

.
 Downloaded from http://www.everyspec.com

.:.

‘#
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION 706
s

RIVET-FLAT
HEAD,HI-SHEAR,
CLOSETOLERANCESHANK
APPLICABLEDOCUMENT: NAS529
(MAX GRI? +2)

H-
I 1

/“ -\
~> ,-/ \
+ A
I

k
\
\ - /
>
JA

Snezr strength
Material Protective finish (psi) min
I

95,900
Alloy steel Cadmium plate <

TABLE 1. Rivet configuration dash numbers.

.:-;
-i-~ ! I .5-:
.4.4 .5.:
-A-i -5-6
.:-~ I

I .5-;
.4.: -5-a
-4.6 I I .5.2
1
.4-9 -5-;0
-4-12 -5-ii
-4-11

t
I .689 ; .750 .5-12
~ 4;: .756 -4- iz .75! ~ .812 .5.13
.8:2 .d.ij .815 .875 -5-i4
.a7~ .4.i4
i ~ ::;; .936 -4.i~
.876 ~ .93a -5-15
I .939 1,000 .4.16
,939 ‘ 1.000 -5- i6
I
1.:01 ‘ 1.062 -5-17
1.CO1 1.062 A-i? -5-16
1.C63 : 1.125
1.063 1,!25 .4.l@ -5-19
.156 .242-.2621
!,4
,.” ,037-,34;1.:26 1.188
188-.20 1 .083 .029-.03 1.:26 1. :8B -4-19 1. i89 ).2s0 -5-20
.125
1.189 1.2s0 -4-23 1.25i :.3!2 -5-21
1.251 1.312 -4-21
1.313 1.375 -5-22
1.313 1.37s -4-22 1.276 1.438 -5-23
1.376 1,438 -4-23 ;.439 1.509 -5-24
].439 1.500 -4-24 1.!51 1.562 -5-25
] ],S62
1.50: -4-25 ;aezs -5-26
I
1.S63 1.625 .4.26 I I 1.563

I I :,$~~ I. ue -5-27
.J.~7 .:-a
I 1.626 I
4.-C. !.;53 -5-28
.J.:? ,-., -5-29
. -m
.“.’-- I ,..:. ,.s12
:.575 -5-30
: 51:
-4-j~
I 1.93’2 -5-31

I
.4.jl
I i

2.900
I
0
:. ?39 ?.Coo .4.;2
.J.::
-4-:4
I
..-t=
.
- -c,>
-.5-:5
. . ..:?.-
I -1
4. ..+
,2
9 . ------ --
6’

-n-<
 Downloaded from http://www.everyspec.com

.:

i’lIL-sTD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

A
I?Ia

.062 L .!25 -6-Z I l———

.126 .X8 .b.~ ,:2$ -8-3
.189 .250 .6.4 .X9 :M ! -8-4
.251 .312
I
1
.jl~ I .375
-6-5
-6-6 I
I
.251
.311
~ .312
, .375
\
I
-8-5
-8-6
/
.3:6 .438 -6-7
.439 ! .500 -6-a
,501 .562 -6-9 -6-3
.563 .625 -6- iC -6- iO
.626 .688 -6-11 .&il

.689 . 7s0 -6-12 -8- i2

.751 .812 -6-13 -~.::
.8!3 .875 .6.14 -a-; i
.876 .938 -6-i5 -a-:5
.939 I. Coo -6-16 -8-16

1.001 1.062 -6-!7 -8-]7

1,063 1.125 -6-18 -8-18
.188 ,295 - .125 .045- 1.1?6 1.188 -6-19 25i3 -3-19
.315 .055 1.189 1.250 -6-23 -8-G3
i. 251 1.312 -6-21 -8-2;
I

1 1.313

/ w
I 1.375
‘ 1.438
1.500
-6-22
-6-23
-6-26
I 1.?12
; ! 376
, 1.:39
-8-22
-8-23
-8-24
I 1.501 1.562 -6-25 ‘1.50! -8-2S
1.563 1.625 -6-26 -8-:6

I
I

I
I
1.626
1.639
: 1.668
1.750
-6-27
-6-28
II I 1.626
~ YCr
-8-27
.3.;?
!.b89 . ----
1.812 -0-29 I i :7:! ~,.
. .. .. -6-:?
:,575 .~.:~ ... :,..
. .. .;. jJ
!.::?
-6-;; ~!; !!.376 : 93s i .3-; ,
t
I
,
-6-32
-6-:3
.0 .;:
I
-6.55
.6-:6
I
(
.126 ; .188 ‘ -10-3
.189 .250 . 1(3-4
,25] I .312 .10.5
.313 .375 I - iO-6
I
-10-7
.10-a
-1o-9
-10-;0
-1o-::

689 .] f-J-;: ,<,.

,..
.75! .10-i3 ,312 .]z.:j
e13 .]0.]4 875 , .12-:4
876 -10-;5 338 ~ -12. !$
.339 Ooc
-10-16
I ‘iZ-’&
I
I 1.001 .10-17 .062 -12-I?
] 1.063 -10-18 .125 -12-16
.312 ~ .475 - 206 .06a -I 1.1?6 -10-19 375 .198 -12-19
-iZ-20
.505 .378 1. ;99
1.2$1
-10-20
-10-21
.$: ., i -1?-21
,I ! I
1.313 : 1.3?5 :10-22 1,11
I , -1. :.375 I -i2-22
1,376 1.:38 -1o-23 ;.3;6 :.43( i -12-23
1 439 , 1.500 -]0.24 i 1.439 1 5’36
I
-12-24 .
1.s01 I 1.56Z . 10-2s I 1.501 :.562 -12-25
1.563 1.625 -10-26 i 561 !.625 I -12-26
t I
1.626 I 1.66a -10-27 1.626 1.668 -12-27
1.689 I 1.750 -1o-28 1.689 1.750 -12.28
1.751 I 1.812 -10-29 1.751 1.912 .12-29
1.813 I ].875 -10-30 1 813 1.875 -12-30
1.876 t 1.938 -10-31 1.876 ‘ 1.938 -12-31
(

1.939 I 2.000 -10-12 1 939 : 290 -12-;2

2 ~ol : 062 I
,~,:~: ::::1 .l~.j~
2.901 2.562 .10-33 -12-i3
- IO-34 ! ? C6Y

I - IO-35
.,,.;: :<3 -,,.,<
..-< .-.
-10-36
I ~
-12-3;

I
NOTE: NAS529-4 thru -12 Rivets to be installed with NAS5Z8
collars of the same dash number. (see section 20?j.

706.2
..
 Downloaded from http://www.everyspec.com

...-
MIL-STD-1759
10 JULY 1979

SECTION 707

RIVET,
SOLID-BELT
APPLICABLEDOCUMENT: MS35745

ArLl

r
Shear strength
Material Protective finish (psi) min
I
t i
Copper None 24,000

TABLE I. Rivet configuration dash numbers.

MS35745
L
D A E F H Dash
Length
number

.375 -6
.500 “7
.625 -8
.165 ●455-.4E .135 .094 072-.05
●750 -9
.875 -lo
1.000 -11

.375 -12
●500 -13
.625 -14
.134 ,395-.41 .109 094 047-.06
-15
●

,750
.875 -16
1.000 -17

-18
-15
-20
.109 ,333-.35 .083 .078 040-.05 -21
,975 -v.
-z?
1.000
----
Downloaded from http://www.everyspec.com

_
 Downloaded from http://www.everyspec.com

...
i“lIL-sTD-1759
10 JULY 1979

SECTION 708

RIVET,SOLID,BUTTON HEAD.STEEL
APPLICABLEDOCUMENT: MS51829

__i H rL~l

Shear strength
I Material Protective finish (psi) min I

Carbon steel
grade M None Not specified

TABLE I. Rivet configuration dash numbers.

I i .;50 ~ -5 ..:7: -:.9

1 .gl~ I -39
1 .500 .875 ,375. .4ofi .37C : I
~ .g~~ I ::
I ~ i::
.40
-41
! -9 I ;:875 -42
I 1.000
-lo a 1.312 562-y ‘ 2.CIOC -43
1.125
1.250 -11 I I ~ 2.:25 -a
“6
?.250 -45
I .625 -12 ‘ -.16
:.375
I .686 -13 2.NO -47
.750 -14 I 2.525 .48
.812 -15 I I 2.750 -*
.875 -16
-17
I 2.975 - ;:
.938 I 3.000 -51
1,000 -18
1.125 -19 t I 1?5(3 -60
].~5(3 -20 ‘ 1; 1.375 -61
1.375 -21 t 1.500 -62
1.500 .2? -o-3
I ; 1.625
.~~ -64
I ‘,.750
4 .625 , 1.094 .469-.
500!;.;;; -24 ! i.375
I
-65
! ;.27: -~
-5 \ :.200
I
-66
I !* ..: C71
.65C-.56?1 - .-
,L.occ -26 ‘ .s/. .--,
-..&.
1*:
-0/
!. s-
I 2.125 -c, I - -c
-6s
1 ---- 2
.;5 -6!!
t [ 2.275 -x ]
I
I :.5aoI -/
:.:75

..- “o
! I 2.:G2
‘~ L-:
,*.”L-
-N
.:.,
~
I .-:.
----
L
-.2L.. -71
.“ -.&
i -73
I I -..
;::;! i :;; : I ..
t ---- -.+
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION 709

RIVET,SOLID-lOOO
COUNTERSUNK HEAD CARBON STEEL,
CORROSION-RESISTANT
STEEL,MONEL
APPLICABLEDOCUMENT: MS20427

I----LI

Shear strength
Material Protective finish
(psi) min
[ ,
i Carbon steel I Cadmium plate/black I 32,000 1
, oxide
Cres Not sDecified 65,000
Monel None/cadmium plate 49,000

TABLE I. Rivet configuration dash numbers.

I
L
Dash numb(
D hi B c Length
Carbon
nom Cres Monel
,125 -2C2 F2-2 M2-2
●188 -2C3 F2-3 M2-3
● .250 -2C4 F2-4 M2-4
.312 -2C5 F2-5 M2-5
.062 .0898 .0317 ● 094
.375 -2C6 F2-6 M2-6
.438 -2C7 F2-7 M2-7
●500 -2C8 F2-8 M2-8
.562 -2C9 F2-9 M2-9
I
.625 -2C1O F2-10 M2-10
‘m -3C3 m m
.250 -3C4 F3-4 /43-4
.312 -3C5 F3-5 M3-5
.375 -3C6 F3-6 M3-6
.438 -3C7 F3-7 M3-7
.1548
.0418 ,140 500
● -3ca F3-8 M3-8
.562 -3C9 F3-9 M3-9
.625 -3C1O F3-10 M3-10
.75’ -3C12 F2-12 M3-12
.875 F3-14 M3-14
1.000 F:-16 p13-~6

7ncl 1.
 Downloaded from http://www.everyspec.com
.
.

.:.

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

MS20427
L Dash number
D HI
‘ B c Length ,
CarDon Monel
Cres
steel
i .

.250 -4C4 F4-4 M4-4

.312 -4C5 F4-5 M4-5
.375 -4C6 F4-6 M4-6
.438 -4C7 F4-7 M4-7
.500 -4C8 F4-8 M4-8
.562 -4C9 F4-9 M4-9
.625 -4C1O F4-10 M4-10
.750 -4C12 F4-12 M4-12
.125 .2006 .0483 .187 .875 -4C14 F4-14 M4- 14
1.000 -4C16 F4-16 M4-16
1.125 -4C18 F4-18 M4-18
1.250 -4C20 F4-20 M4-20
1.375 -4C22 F4-22 M4-22
1.500 -4C24 F4-24 M4-24
1.750 -4C28 F4-28 M4-28

.312 -5C5 F5-5 M5-5

.375 -5C6 F5-6 M5-6
.438 -5C7 F5-7 M5-7
500
● -5C8 F5-8 M5-8
.562 -5C9 F5-9 M5-9
.625 -5Ci0 F5-10 M5-10
.688 — — M5-11
.750 -5C12 F5-12 M5-12
.156 .2566 .0614 .234
.875 -5C14 F5-14 M5- 14
1.000 -5C16 F5-16 M5-16
1.125 -5C18 F5-18 M5-18
1*250 -5C20 F5-20 M5-20
1.375 -5C22 F5-22 M5-22
1.500 -5C24 F5-24 M5-24
1.750 -5C28 F5-28 M5-28
2 000
● -5C32 F5-32 M5-32

709.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

. MS20427
L
Dash number
D A1 B c Length
Carbon
Cres Monel
steel

.375 -6C6 F6-6 M6-6

.438 -6C7 F6-7 M6-7
500
● -6C8 F6-8 M6-8
.562 -6C9 F6-9 M6-9
.625 -6C1O F6-10 M6-10
.750 -6C12 F6-12 M6-12
.188 .3234 .0769 .281
.875 -6C14 F6-14 M6- 14
1 000
● -6C16 F6-16 M6-16
1.125 -6C18 F6-18 M6-18
1.250 -6C20 F6-20 M6-20
1.375 -6C22 F6-22 M6-~2
1.500 -6C24 F6-24 M6-24

1.750 -6C28 F6-28 fq6-~8

2 000
● -6C32 F6-32 M6-32
2,500 -6C40 F6-40 M5-40
3 000
● -6C48 F6-J8 M6.48

●500 -8C8 F8-8 M8-8

.562 -8C9 F8-9 MB-9
.625 -8C1O F8-10 M8- 10
.750 -8C12 F8-12 M8-i2
.875 -8C14 F8-14 M8-~4
1.000 -8C16 F8-16 M8-16
1.125 -8C18 F8-18 M8- 18
.250 .4412 ● 1034 .375 F8-~o
1.250 -8C20 M8- 20
1.375 -8C22 F8-~2 M8-22
1 500”
● -8C24 F8-24 M8-24
1.750 -8C28 F8-28 M8-28
2,000 -8C32 F8-32 M8-32
2.500 -8C40 F8-40 M8-40
3.000 -8C48 F8-48 M8-48
Downloaded from http://www.everyspec.com

.-

.
 Downloaded from http://www.everyspec.com

—.
MIL-STD-1759
10 JULY 1979

SECTION 710

RIVET,SOLID,COUNTERSUNK 100°,PRECISIONHEAD,
ALUMINUM AND ALUMINUM ALLOY
APPLICABLEDOCUMENT: MS2t1426

o------L-

‘r
N
A
100°

I
t-c-i

Shear strength
Material Protective finish
(psi) min
.

Aluminum 11OO-F None Not specified

5056-H32 Anodize 24,000

Aluminum 2117-T4 Anodize 26,000

alloy
2024-T4 Anodize 37,000

2017-T4 Anodize 33,000

——.
Downloaded from http://www.everyspec.com
.

..

.
MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers.

L MS20426Oas h number
D A B c Length ,Aluminum Aluminum allov (
11OO-F 5056H32 2117-T4 - 20Z4-T4 2017-T4’
u
.125 A2-2 B2-2 AD2-2 DD2-2 D2-2
.188 A2-3 B2-3 AD2-3 DD2-3 02-3
.250 A2-4 B2-4 AD2-4 DD2-4 D2-4
.312 A2-5 62-5 AD2-5 DD2-5 D2-5
,062 .114 .022 ● 094 .375 A2-6 62-6 AD2-6 DD2-6 D2-6
.438 A2-7 B2-7 AD2-7 DD2-7 02-7
.500 A2-8 B2-8 AD2-8 DD2-8 D2-8
.562 A2-9 B2-9 AD2-9 DD2-9 D2-9
.625 A2-10 B2-10 AD2-10 DD2-10 D2-10

.188 A3-3 B3-3 AD3-3 DD3-3 D3-3

.250 A3-4 B3-4 AD3-4 DD3-4 D3-4
.312 A3-5 B3-5 AD3-5 DD3-5 D3-5
.375 A3-6 B3-6 AD3-6 DD3-6 D3-6
,428 A3-7 B3-7 AD3”7 DD3-7 D3-7
.500 A3-8 63-8 AD2-8 DD3-8 D3-a
A3-9 ~3-g AD3-9 DD3-9 D3-9
*094 .179 .036 .141 .562
.625 A3-10 B3-10 AD3-10 DD3-10 D3-10
.750 A3-12 B3-12 AD3-12 DD3-12 D3-12
.875 “ - B3-14 AD3-14 - 03-14
- B3-16 AD3-16 - D3-~6
1*000
1.250 - B3-20 AD3-20 -
2.000 - AD3-32 -

A4-4 AD4-4 D4-J

.250
A4-5 AD4-5 : D4-5
,312
.344 AD4-5-5 -
.375 A4~6 B4-6 AD4-6 - D4-6
.438 A4-7 B4-7 AD4”7 D4-7
●500 A4-8 B4-8 AD4-8 ~D4~8 D4-8
.562 A4-9 B4-9 AD4-9 DD4-9 D4-9
.125 ,225 .042 .188 D4-10
.625 A4-10 B4-10 AD4-10 DD4-10
.750 A4-12 B4-12 AD4-12 DD4-12 04-12
.812 AD4-13 -
.875 A4114 B4~14 AD4-14 DD4-14 -
D4-14
1.000 A4-16 B4-16 AD4.16 DD4-16 D4-16
1.125 A4-18 B4-18 AD4-18 - D4-18
1.250 A4-20 64-20 AD4-20 - D4-20

710.2
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

MS20426 Dash number

L
D A B c Aluminum Aluminum allov
Length 2024-T4 2017-T4
I1OO-F 5056H32 2117-T4

1.375 A4-22 84-22 AD4-22 - 04-22

.125 .225 .042 .188 1.500 A4-24 B4-24 AD4-24 - @4-24
1.750 A4-28 B4-28 AD4-28 - D4-28

.312 A5-5 AD5-5 - 05-5

.375 A5-6 B5-6 AD5-6 DD5-6 05-6
.438 A5-7 B5-7 AD5-7 DD5-7 D5-7
.500 A5-8 65-8 AD5-8 DD5-8 05-8
.562 A5-9 B5-9 AD5-9 DD5-9 D5-9
.625 A5- 10 B5-10 AD5-10 DD5-10 D5-10
.688 - AD5-11 -
.750 A5-12 B5-12 AD5-12 DC5-12 05-12
.156 .286 .055 .234 AD5-14 DD5-14 D5-14
.875 A5- 14 B5-14
1 000
● A5-16 B5-16 AD5-16 DD~-16 D5-16
1.125 A5-18 05-18 AD5-18 DD5-18 D5-18
1.250 A5-20 B5-20 AD5-2CI - D5-20
1.375 A5-22 B5-22 AD5-22 - D5-22
1.500 A5-~& %5-24 AD5-24 - 05-24
1.750 A5-28 B5-28 AD5-28 - D5-28
2.000 A5-32 %5-32 AD5-32 - D5-32

.312 - AD6-5
.375 A6-5 B15-6 AD6-6 DD6-5 D6-6
,438 A6-7 B6-7 AD6-7 D!36-7 D6-7
.500 A6-8 B6-8 AD6-8 DD6-8 D6-8
.562 A(j-g B(j-$) AD6-9 DD6-9 D6-9
.625 A6-10 B6-10 AD6-10 DD6-10 D6-10
.688 AD6-11 -
.750 A6~12 B6-12 AD6-12 DD6-12 D6-12
.875 A6-14 B6-14 AD6-14 DD6-14 D6-14
,187 .353 ● 070 .281 .938 - AD6-15 -
1.000 A6-16 B6-16 AD6-16 DD6-16 D6-16
1.125 A6-18 B6-18 AD6-18 DD6-18 06-18
1.250 A6-20 B6-20 AD6-20 DD6-20 D6-20
1.375 A6-22 B6-22 AD6-22 DD6-?2 D6-22
1.500 A6-24 B6-24 AD6-24 DD6-24 06-24
1.750 A6-28 B6-28 AD6-28 DD6-28 06-28
2 000
● A6-32 B6-32 AD6-32 DD6-32 06-32
2.500 A6-40 %6-40 AD6-40 DD6-40 D6-40
3.000 Afj-a/3 B6-48 AD6-48 DD6-4S D6-48

710.3
 Downloaded from http://www.everyspec.com
.

-
MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

L MS20426 Dash number

D A B c Length Aluminum Aluminum alloy
11OO-F 5056H32 2117-T4 I 2024-T4 I 2017-T~

.438 B8-7 AD8-7 08-7

.500 %8-8 AD8-8 08-8
.562 B8-9 AD8-9 D8-9
.625 B8-10 AD8-10 D8-10
.750 B8-12 AD8-12 08-12
,875 A8-14 B8-14 AD8-14 D8-14
1.000 A8-16 B8-16 AD8-16
1.125 A8-18 B8-18 AD8-18
.250 .476 .095 .375 A8-20 B8-20 AD8-20
1.250
-
1*375 A8-22 B8-22 AD8-22
1.500 A8-24 68-24 AD8-24
1.750 A8-28 B8-28 AD8-28 .
2.000 A8-32 B8-32 AD8-32
2.125 AD8-34
2.500 A8-40 B8~40 AD8:40
3.000 A8-48 B8-48 AD8-48

710.#
 Downloaded from http://www.everyspec.com

..

)IIL-STD-1759
10 JULY 1979
SECTION 711

SOLID-COUNTERSUNK
RIVET, HEADBRASSOR COPPER
APPLICABLEDOCUMENT: MS51945

-L=L—

v
I

?
Shear strength
Material Protective finish
(psi) min
!

I I I 1
Brass None 35,000 “

Copper None 24,000

b 4

TABLE 1. Rivet configuration dash numbers.

MS51945 Dash number

D A H L
Length Brass Copper

.250 -1 -
.438 -4
.094 .171-.176 .040 .625 -7
.750 -8 -

●188 -115
.250 -15 -116
.312 -16 -
.375 -17 -117
.438 -Is
.125 .227-.235 .053 .500 -Is -116
,625 -z: -~~g
,750 -l~g
.875 -23 -
1.375 -25 -
-p7
2.500
J

711.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759 v

10JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

MS51945 Dash number

D A H L
Length Brass Copper

.438 -32 -
.156 .284-.293 .066 .562 -34 -

.250 -142
.312 -44 -
.375 -143
●500 -47 -144
.625 -49 -145
.750 -50 -146
● 188 .340-.351 .079 .875 -147
1.000 -148
1.250 -149
1.375 -53 -
1.750 -151
2 000
● -54 -
2.250 -55 -
3.000 -56

500
● -157
.625 -158
.750 -63 -159
.875 -160
.250 .455-.469 .106 1.000 -65 -16i
1.250 -162
1.500 -i63
1.750 -164
2.000 -165
.
.750 -172
.875 -173
1 000
● -174
.312 .569-.588 .133 1.250 -175
1.500 -176
1.750 -177
2.000 -178

1.000 -187
1*250 -188
.375 .682-.704 •1~~
1.500 -189
1,750 -lQO
 Downloaded from http://www.everyspec.com

M:L-STD-1759
10JULY 1979

SECTION 712

FLUSHHEAD
RIVET-SOLID-lOOO
A2!16
CORROSIONRESISTANTSTEEL
APPLICABLEDOCUMENT: NAS1199

Shear strength
Material Protective finish
(psi) min

Cres A286 Passivate 90,000

TABLE I. Rivet configuration dash numbers.

L
Dia Al B NAS1199
Length
Dash No.

.
.125 -2-2
●188 -2-3
.250 -2-4
.312 -2-5
.062 ,090 .032 .375 -2-6

.438 -2-7
●500 -2-a
.563 -2-9

712.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

A1 L
Dia B NAS1199
Length
Dash No.

.188 -3-3
.250 -3-4
.312 -3-5
.375 -3-6
.438 -3-7
.094 .155 .042
.500 -3-8
.563 -3-9
.625 -3-1o
.688 -3-11
●750 -3-12

.250 -4-4
.312 -4-5
.375 -4-6
.438 -4-7
,500 -4-8

.563 -4-9
.625 -4-10
.125 ● 200 .049 .688 -4-11
.750 -4-12 .
.813 -4-13

.875 -4-14
.938 -4-15
1.000 -4-16
1,125 -4-18
1,250 -4-20
.250 -5-4
.312 -5-5
.375 -5-6
.438 -5-7
.500 -5-8

.563 -5-9
.625 -5-1o
.156 .257 .061 .688 -5-11
.750 -5-12
.813 -5-13

,875 -5-14
.938 -5-15
1.000 -5-16
1.125 -5-18
lo~~) ‘5-20
 Downloaded from http://www.everyspec.com

...
P?IL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

1 L
Dia A B NAS1199
Length
Dash no.

.375 -6-6
.438 -6-7
●500 -6-8
.563 -6-9
.625 -6-10

.688 -6-11
.187 .441 ● 103 .750 -6-12
.813 -6-13
.875 -6-14
.938 -6-15

1 000
● -6-16
1.125 -6-18
le250 -6-20

.375 -8-6
.438 -8-7
.500 -8-8
.563 -8-9
,625 -8-10

,688 -8-11
● 250 .441 ,103 .750 -8-12
.813 -8-13
●
.875 -8-14
.938 -8-15

1.000 -8-16
1.125 -8-18
1.250 -8-20

NOTE : Suggested shank length protrusion

1-1/4 to 1-1/3 times rivet diameter.
Downloaded from http://www.everyspec.com
 Downloaded from http://www.everyspec.com

-----
MIL-STD-1759
10 JULY 1979

SECTION713

RIVET,
SOLID,
100°FLUSH HEAD,AMS7229
APPLICABLEDOCUMENT: AN123451THRU AN123600

100°
/

- t i i
Shear strength
Material Protective finish (psi) min

Cres 18Cr-llNi Not Specified Not Specified

I I

TABLE 1. Rivet configuration Dart numoers.

D A B c L Part no.

.219 AN123461
.250 AN1Z3453
.281 AIJ123462
.312 AN123454
.344 AN123463

.375 AN123455
.406 AN123464
.062 ● 105 .022 .112 .438 AN123456
.469 AN122465
.500 AN123457

● “1
dti AI1122466
.;;2 AN123458
.~~d Ar4123467
fln~
.OL. AN12:459
 Downloaded from http://www.everyspec.com

-.

MIL-STD-1759
10JULY 1979

TABLE I. Rivet configuration part numbers. - Continued

D A B c L Part no.

.281 AN123480
.312 AN123470
.344 AN123481
.375 AN123471
.406 AN123482

.438 AN123472
.469 AN12:4/33
● 094 4170 .036 .169 ,500 AN123473
.531 AN123484
.562 AN123474

.594 AN1234j35
.625 /Vl123475
.656 A/{123499
,688 AN123500
.719 AN123501
.344 AN12:533
.375 AN122487
.406 AN122534
.438 AN1234~8
,469 AN123535

●500 Aii12248Q
.125 .216 .042 .225 .531 AN1235:6
.552 AN12245Q
.~gd AN1235~7
,625 AN123dSi

,656 AN122548
.688 AN123549
.
.719 AN123560

.406 AN12:585
.438 AN123504
.469 AM123586
,500 AN123505
.5:1 AN123587
.156 .278 .055 .281
.562 AN123506
,554 AN122588
.625 A!1122507
n m---
,1
.638 *11L&::?o
●

,719 ~1
‘[]~:~:1

●500 AFl12252~
.188 ,:43 .070 .2:3 .562
19,*-----

Mli&-””&;
. .

--
c
; ;;{]::~::
.Oc”

715.2
Ao
 Downloaded from http://www.everyspec.com

..-
MIL-STD-1759
10 JULY 1979

SECTION 714

RIVET,
SOLID,100°FLUSH HEAD,AiYlS7232
APPLICABLEDOCUMENT: AN123601THRUAN123750

100°
.
\
ry , Tr I-C<
I
I

.I
1
1-

/ b -nu

V
Shear strength
Material Frc:ec:ive finish (psi) min

Cres
ls.SCr-llNi Not Specified Not SDecified .

TABLE I. Rivet configuration aar: numbers.

n“ A B c L Part no.
Lengtn
I
I

AN123602
AN123611
AN123603
AN123612
I AN123604

AN123613
AN123605
,062 .105 I .022 I .112 AN123614
I
A::1236C6
I 4N122615
I
!
I
I ::;122507
,4!;12:6~5
I 4!/12:608
:2J
.-.
.--#.-
,“--

71,1 1 .-.
—
Downloaded from http://www.everyspec.com

.:

MIL-STD-1759
10JULY 1979

TABLE I. Rivet configuration part numbers. - Continued

A B L
D c Part no,
Length

.250
AN1236i9
.281 AN123630
“.312 AN213620
.344 AN123631
.375 AN123621

.406 AN123632
.438 AN123622
.469 AN123633
.094 .170 .036 .169 .500 AN123623
.531 AN123634

.562 AN123624
.554 AN123635
.625 AN123625
.656 AN123649
.688 AN123650

.3:2
.344
.375
.4C6
,438

.469
,500
125 .042
.. .216 .225 ,531
.562
.594
.525 A!J1236GI
.656 AN122698
.68$ A:i12369?
.719 AN123700

.406 AN123735
,438 AN123654
.463 At4123736
.500 AN123655
.531 AN123737

.156 .278 .055 .281 .562 AN123656

.594 AN123738
.625 AN123657
,656 AN123739
.688 AN123740

I Aii123741

,344 ,070 .338

714>2,\
 .
Downloaded from http://www.everyspec.com

.:

MIL-STD-1759
10JULY 1979

SECTION 715

RIVET,
SOLID-lOOO
FLUSHHEAD,AMS7233
APPLICABLEDOCUMENT: MS9318

1000 I

u’ “L 1 #’
D

Shear strength
Material Protective finish (psi) min
I

Nickel copper Not Specified Not Specified

alloy

67Ni-30Cr
I

TABLE I. Rivet configuration dash numbers.

L
D A c Length
MS9318
Dash no.
I
,156 -003
.188 -004
.219 -005
.259 -006
.099 - .022 .094 .281 -007
.062
.107
.312 -008 “
●344 -009

.250 -052
.281 -053
.312 -054
.344 -055
.375 -056

.406 -057
.438 -058
.469 -059
.164 - .036 .141 ,500 -060
.094
.172 .531 -061

,562 -062
L.
.594 -063
,625 -064

-1
.65a -065
.688 -066

.719 -067
 —
Downloaded from http://www.everyspec.com

rfIL-sTD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

D A L
8 c MS9318
Length
Dash no.

.281 -099
.312 -1oo
.344 -101
.375 -102
.406 -103
.125 .210 - .042 .188 .438 -104
.218 .469 -105
.500 -106
.531 -107
.562 -108

.594 -109
.344 -147
.375 -148
.406 -149
.438 -150
.469 -151
.156 .272 - .055 .234
.280 .500 -152
.531 -153
.562 -154
.594 -155

.406 -195
,438 -196
.469 -197
.188 .337 - .500 -198
.347 .070 .281 I .531 -199

.562 -200
.594 -201
 Downloaded from http://www.everyspec.com

..-
MIL-ST’D-1759
10JULY 1979

SECTION 716

FIIVET,
SOLID-1
OO” FLUSH HEAD,AMS7235 -
APPLICABLEDOCUMENT: MS9460

100°

v
!
Shear strength
Material Protective finish (psi) min

Cres 15 Cr-26fii Pione 90,000

TABLE I: Rivet configuration dash numbers.

L
A B c MS9460
Length
Dash no.

.250 -052
.281 -053
.312 -054
.344 -055
.375 -056
.094 .164 - .036 .141
.172
.406 -057
.438 -058
.469 -()~g
 Downloaded from http://www.everyspec.com
.

..

MIL-STD-1759 --
10 JULY 1979

TABLE 1, Rivet configuration dash numbers. - Continued

L
D A B c MS9460
Length
Dash no,

.312 -1oo
.344 -101
.375 -102
.406 -103
.438 -104

.469 -105
.500 -106
.531 -107
.125 .210 . .042 ● 188 .562 -108
.218 .594 -109

.625 -110
.656 -111
.688 -112
.719 -113

.375
.406
,438 -150
.469 -151
●~oo -152

.531 -152
.156 .272 . .055 .234 .562 -154
.280 ●594 -155
.625 -156
.656 -157

-158
-159

.375 -194
,406 -195 .
.438 -196
,469 -197
,500 -198

.188 .337 ● 070 .281 .531 -199

.347 .562 -200
KGd
.“- -201
.625 -202
.655 -203

-204
-205
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION717

RIVET,SOLID,100°FLUSH SHEAR HEAD

A286 CORROSIONRESISTANTSTEELAND MONEL
APPLICABLEDOCUMENT: NAS1200 -

f I

Shear strength
I Material
I
Protective finish (psi) min

I
I Passivate 90,000
Cre~ A286
Nickel copper’ None or 49,000
alloy (Monel)I cadmium plate
I I

TABLE I. Rivet confi -Iuration art numbers.

Basic
A1
Absolute B part
Dia inindia (Ref) number

.094 .021 NAS1200-3

.~25 .029 NAS1200-4
●037 iwslzoo-5
.156
.046 NASi200-6
.187
,250 .060 f{ASi20G-3
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE II. Rivet configuration dash numbers.

Length and dash number

Dia
—
.188 .250 .312 375 I .438 ,500 .563 .625 .688 .750
-,
●

.094 -3 -4 -5 -8 T -lo I -11 -12

.125 -- -4 -5 -8 -9 -lo -11 -12
.156 -- -4 -5 -6 -7 -8 -9 -lo -11 -12
.187 -- -- -5 -6 -7 -8 -9 -lo -11 -12
●25O -- -- -- -- -7 -8 -9 -lo -11 -12
I

Dia Length and dash number

ZEl 1,000
.094 -15 I -16
.125 -13 -14 -15 -16
.156 -13 -14 -15 -16
.187 -13 -14 -15 -16
,250 -13 -14 -15 -16

Suggested shank length protrusion 1-1/4 to 1-1/3 times

rivet dia.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

sECTION 718

WET, SOLID-lOOO
FLUSHSHEARHEAD,ALUMINUM ALLOY
APPLICABLEDOCUMENT: NAS1097

I Shear strength
Material Protective finish (psi) min
I

Anodize 26,000
2117-T4
Anodize 24,000
Aluminum 505J5-H32
Anodize 33,000
alloy 2017-T4
Anodize 37,000
2024-T4
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers.

L NAS1097 Dash number

D A1 B G
Length 5056H32 2117-T4 2024-T4 2017-T4

.250 B-3-4 AD-3-4 DD-3-4 D-3-4

.312 B-3-5 AD-3-5 DD-3-5 D-3-5
.375 B-3-6 AD-3-6 DD-3-6 D-3-6
.438 B-3-7 Ail-3-7 DD-3-7 D-3-7
●500 B-3-8 AD-3-8 DD-3-8 D-3-8 .
● 094 .126 .021 .141
.562 B-3-9 AD-3-9 DD-3-9 D-3-9
.625 B-3-1O AD-3-lo DD-3-1O D-3-1O
.750 B-3-12 AD-3-12 DD-3-12 D-3-12
.875 B-3-14 AD-3-14 DD-3-14 D-3-14 4

1.000 B-3-16 AD-3-16 DD-3-16 D-3-16

.250 B-4-4 AD-4-4 DD-4-4 D-4-4

.312 B-4-5 AD-4-5 DD-4-5 D-4-5
.375 B-4-6 AD-4-6 DD-4-6 D-4-6
.438 B-4-7 AD-4-7 DD-4-7 D-4-7
.500 B-4-8 AD-4-8 DD-4-8 D-4-8
.562 B-4-9 AD-4-9 DD-4-9 D-4-9
.625 B-4-1O AD-4-lo DD-4-1O D-4-1O
.125 .174 .029 .188 .750 B-4-12 AD-4-12 DD-4-12 D-4-12
..875 B-4-14 AD-4-14 DD-4-14 D-4-14
1.000 8-4-16 AD-4-16 DD-4-16 D-4-16
1.125 B-4-18 AD-4-18 DD-4-18 D-4-18
1.250 6-4-20 AD-4-20 DD-4-20 D-4-20
1.375 B-4-22 AD-4-22 DD-4-22 D-4-22
1.500 B-4-24 AD-4-24 DD-4-24 D-4-24
1.750 B-4-28 AD-4-28 DD-4-28 D-4-28

.312 B-5-5 AD-5-5 DD-5-5 D-5-5

.375 B-5-6 AD-5-6 DD-5-6 D-5-6
.
.438 B-5-7 AD-5-7 DD-5-7 D-5-7
.500 B-5-8 AD-5-8 DD-5-8 D-5-8
.562 B-5-9 AD-5-9 DO-5-9 D-5-9
.625 B-5-1O AD-5-lo DD-5-1O D-5-1O
.750 B-5-12 AD-5-12 DD-5-12 D-5-12
.156 .225 .037 .234
.875 B-5-14 AD-5-14 DD-5-14 D-5-14
1.000 B-5-16 AD-5-16 DD-5-16 D-5-16
1.125 B-5-18 AD-5-18 DD-5-18 D-5-18
1.375 6-5-20 AD-5-20 DD-5-20 D-5-20
1.500 B-5-24 AD-5-24 DO-5-24 D-5-24
~0750 B-5-28 AD-5-28 DD-5-28 D-5-28
2.000 B-5-32 AD-5-32 DD-5-32 D-5-32

718.2 \6-
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

L NAS1097 Dash number

D B G 2117-T4 - 2017-T4
Length -

.375 B-6-6 AD-6-6 DD-6-6 D-6-6

.438 B-6-7 AD-6-7 DD-6-7 D-6-7
●500 B-6-8 AD-6-8 DD”6-8 D-6-8
.562 B-6-9 AD-6-9 DD-6-9 D-6-9
.625 B-6-lo AD-6-lo DD-6-1O D-6- 10
.750 B-6-12 AD-6-12 DD-6-12 D-6-12
.875 B-6-14 AD-6-14 DD-6-14 D-6-14
.046 .281 1.000 B-6-16 AD-6-16 DD-6-16 D-6-16
,188 ,275
1.125 B-6-18 AD-6-18 DD-6-18 D-6-18
1.375 0-6-20 AD-6-20 DD-6-20 D-6-20
1 500
●
B-6-24 AD-6-24 DD-6-24 D-6-24
1.750 B-6-28 AD-6-28 DD-6-28 D-6-28
2.000 B-6-32 AD-6-32 DD-6-32 D-6-32
2.500 B-6-40 AD-6-40 DD-6-40 D-6-40
3.000 B-6-48 AD-6-48 DD-6-48 D-6-48

,500 B-8-8 AD-8-8 DD-8-8 D-8-8

,562 B-8-9 AD-8-9 DD-8-9 D-8-9
.625 B-8-lo AD-8- 10 DD-8-1O D-8- 10
.750 0-8-12 AD-8-12 DD-8-12 D-8- 12
.875 B-8-14 AD-8-14 DD-8-14 D-8-14
1 000● B-8-16 AD-8-16 DD-8-16 D-8-16
1,125 B-8-18 AD-8-18 DD-8-18 D-8-18
.250 .371 .060 .375 B-8-20 AD-8-20 DD-8-20 D-8-20
1,250
1.375 B-8-22 AD-8-22 DD-8-22 D-8-22
1.500 B-8-24 AD-8-24 DD-8-24 D-8-24
1.750 B-8-28 AD-8-28 DD-8-28 D-8-28
2.000 B-8-32 AD-8-32 DD-8-32 D-8-32
2.500 B-8-40 AD-8-40 DD-8-40 D-8-40
3.000 B-8-48 AD-8-48 DD-8-48 D-8-48

L-

718.:
 Downloaded from http://www.everyspec.com

.-

.. .

,.
 Downloaded from http://www.everyspec.com

.:.

---
MIL”STD-1759
10 JULY 1979

SECTION719

RIVET,
SOLID-SMALL,
COUNTERSUNKHEAD,STEELANNEALEII
APPLICABLEDOCUMENT: MS35744

rL---l

p.r
1
90°
H

b“
-.

I
Shear strength
I Material Protective finish
(psi) min

E None 32,000

TABLE I. Rivet configuration dash numbers.

MS35744
D. A H L Dash
Length number

.375 -1
.438 -2
500
● -3
.562 -4
.625 -5
688
● -6
,750 -7
.125 .217.-235 .053 .875 -8
1.000 -9
1.125 -lo
1.250 -11
1.375 -12
1 500
● -13
1.750 -14
2 000
● -15

----
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet conffquration dash numbers. - Continued

MS35744
D A H L Dash
Length number

.375 -16
..438 -17
500
● -18
.562 -19
.625 -20
.688 -21
750
● -22
.188 .326-.351 .079 .875 -23
1 000
● -24
1.125 -25
.-
1.250 -26
1.375 -27
1.500 -28
1.750 -29
2.000 -30

500
● -31
.562 -32
.625 -33
●688 -34
.750 -35
.875 -36
.250 .437-.469 .106 1.000 -37
1.125 -38 ‘
1.250 -39
1.375 -40
1 500
● -41
1.750 -42
2 000
● -43

719.2
● ✎✎
 Downloaded from http://www.everyspec.com

.
MIL-STD-1759
10 JULY 1979
SECTION720

SOLID-SMALL,
RIVET, PAN HEAD,STEEL,
ANNEALED
APPLICABLEDOCUMENT: MS35743

?
Shear strength
Material Protective finish (psi) min

Carbon steel
None 32,000
cloo\hru ~1022
●

TABLE I. Rivet configuration dash numbers.

MS35743
L Dash
D A H l_ength
number
.250 -1
.312 -2
.375 -3
.438 -4
.500 -5
.562 :;
.125 205-.225 ,066-.078 .625
.750 -8
.875
1.000 -i:
L
1.125 -11
1.250 -12

.. i! ----
 Downloaded from http://www.everyspec.com

,.

MIL-STD-1759
10 JULY 1979

TABLE 1. Rivet configuration dash numbers.= Continued

MS35743
D A H L Dash
Lengthnumber
.250 -13
.312 -14
.375 -15
.438 -16
.500 -i7
.562 -18
.625 -19
.750 -20
.875 -21

.188 308-.334 1 100-.11’

1.000
1.125
1.250
-22
-23
-24
1.375 -25
1.500 -26
1.625 -27
1.750 -28
2.000 -29
2.250 -30
2.500 -31
2.750 -32
3.000 -33

.375 -34
.438 -35
.500 -36
.562 -37
.625 -38
.750 -39
,875 -40
1.000 -41
1.125 -42
.250 414-.4441135-.15 1.250 -43
1.375 -44
1.500 -45
1.625 -46
1.750 -47
2.000 -48
2.250 -49
2.500 -50
2.750 -51
3.000 -52
3.500 -53
4.000 -54

.625 -55
.750 -56
.875 -57
1.000 -58
1.125 -59
1.250 -60
1.375 -61
1.500 -62
.312 518-.552 .169-. 18; 1.625 -53
1.750 -64
2.900 -65
2.250 -66
2.500 -67
2.Z50 -68
3.COO -69
3.500 -70
I 4.000 -71
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION721

RIVET,SOLID-TINNER’S
APPLICABLEDOCUMENT: MS51931

‘lJ-”L-l
u t. i-A

Shear strength
Material Protective finish (psi) min

Carbon steel
C1006t$ru ~1012 None or tinned 32,000
& I

TABLE I. Rivet configuration dash numbers.

MS51931
L Dash number
A B H Length
● Uncoated Tinned

.085-.091 .205-.225 .024-.036 .156 -1 -15

.101-.107 .245-.265 .025-.037 .188 -2 -16
.107-.113 .265-.285 .028-.040 .203 -3 -17
.126-.132 .294-.316 .034-.046 .234 -4 -18
.140-.146 .319-.341 .036-.050 .266 -5 -19
.144-.150 .289-.311 .055-.069 .281 -6 -20
.154-.163 .303-.329 .059-.073 .313 -7 -21
.170-.179 .342-.368 .062-.076 ●344 -8 -22
.197-.206 .393-.419 .076-.090 .391 -9 -23
.218-.227 .445-.475 .085-.101 .438 -10 -24
.232-.241 .475-.505 .088-.104 .469 -11 -25
.251-.263 .498-.532 .090- .108 .500 -12 -26
,276-.288 .543-.577 .095-.113 .515 -13 -27
.292-.304 .563-.597 .110- .128 .531 -14 -28
d

- */--\
 Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
IOJULY 1979

SECTION722

RIVET,SIILID-UNIVERSAL
HEMI
APPLICABLEDOCUMENTS:MS2047a MS20613,MS20615
.

I
\ I

b-
L
I

L“
DIA
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE 1. Part numbers.

Al uml num Aluminum Aluminum Alun\num

Hatertal .a . . . .. e.... Cmper Mone 1 Mone 1
1100 alloy 2117 ! ~]lOj’ 5056 alloy 2017

Protective finish . . , . . . . . . None Anoa4 ze None Iionc Cad. plate

!iOt 24,000 33,0D0 49,000

Shewstnngth (psi rein )....... Specified 26 ,ODO 17.000
I

Dia A 0 c Lekgth RS20470 dash nwrtters ?620615 dash nubers

.125 -- .. -- -- 2 CU2 2H2 2MP2

.187 -- -. . . -. 2 CU3 2N3 2nP3
.188 M2- 3 -. -- .-
.250 ::: AD2-4 .. .- 2;;4 2ii
.312 AZ-5 A02-5 -. .- 2 CU5 2!!5 E!

.375 A2-6 AD2-6 -- .- ;C# 2?IP6

.438 U-7 AD2-7 -. .- :: 2MP7
.062 .125 .094 .027 .500 A2-8 A02- 8 .- -. 2 CU8 2n8 &PB
. S62 AZ-9 AD2-9 -. .- -. 2M9 2W9
.625 AZ-lo AD2-10 .- .. -. .. ..

.750 AZ-12 AD2-12 -- -. .- .- ..

.875 A2-14 AD2-14 -- .. -. .. ..
1.000 A2-16 A02-16 .- -- .- -. .-
1.125 A2-18 A02- 18 .. . . -- .. . .
1.250 A2-20 AD2-2il -. .- -- .- .-

.187 -- .- -. -. 3CU3 3tu 3RP3

.188 A3-3 AD3-3 .- D3-3 --
.250 A3-4 A03-4 -. D3-4 3CU4 ‘-
3M4 3;4
.312 A3-5 AD3- 5 -. 03-5 3CU5 3H5 3MP5
.375 A3-6 AD3-6 -- 03-6 3CU6 3M6 3MP6
.

.438 A3-7 AD3 -7 -. 03-7 3CU7 3P17 3MP7

.500 A3-8 AD3-8 .. 03-8 3CU8 3W8
.562 A3-9 AD3-9 -. D3-9 -. % 3nP9
.187 .141 ,040 .625 A3-10 AD3-10 .- D3-10 3culo 3H1O 3MP1O
.094
.688 -- .- -- -. .. 3tll 1 3W11

.750 A3-12 AD3-12 -. D3-12 3W12 3?112 3nP12

.8?5 A3-14 A03-14 -- 03-14 3CU14 -- ..
1.000 A3-16 AD3-16 -- 03-16 3CU16 -- ..
1.125 A3-18 A03-18 -. 03-18 -. .. ..
1.250 A3-20 A03-2C -- 03-20 -. -- ..

1.375 A3-22 AD3-22 .- 03-22 . . -. ..

)

722.2
 Downloaded from http://www.everyspec.com

MrL-sTD-1759
TABLE 1. Part numbers.-Continued 10 JULY 1979

?,
I E c

~
L
en,:’
.. ADA-3-5 04-3-5 .. .. ..
Mme 1
&o. ~lal
..
A4-4 A04-4 04.4 !)4.4 4CU4 4U4 4W’4
.Ze: .- AM- J-5 84.4.5 .. .- ..
.312 A4-s A04- s 64-5 DL5 4CU5 4n5 4MP5
.3?5 A4-6 404-6 94.6 04-6 4CU6 AM AMP6

.43S A4.7 A04- ? 84-7 04-7 4CU7 4!47 4MP7

.500 A4-8 A04-8 B4-8 04-8 4CU8 ARB 4NP8
.562 A4-9 A04-9 84-9 04-9 .. An9 4nP9
.625 A4- 10 ADA-10 84-10 M-lo 4CU1O 4U1O 4NP10
.687 .- AD4- I 1 04-11 -. .. -. .-
.125 .250 .186 .054
.688 -- .- .. .. .- Amll 4mPlJ
.750 A4-12 M)4- 12 04-12 04-12 4CU12 4W2 4nP12
.812 .. .. .. -. .. 4P113 4MP13
,875 A4- 14 AM- 14 B4-14 D4-14 4CU14 4M]4 4MP] 4
.938 .. .. .. .- .. 4?!15 Awls

1.000 M-16 M4-16 04.16 04-16 40J16 41416 A14P16

1.125 A4-18 A04-18 84.18 M-18 -- 4H18 414P18
1.259 M-20 AOA-20 B4-20 M-20 .. Awo 4KP20
1.37S M-22 AD4-22 S4-22 04-22 .. .. .-
1.5Q0 A4-24 AM-24 B4-24 04-24 .. .. ..
T -. .- .. .. ..
.312 AG A05- 5 B5-5 D;Z5 .- 5R5 gtP5
.375 AS-6 ADS-6 85-6 05-6 5CU6 944 5!(P6
.42e A5- 7 A05-7 85-7 C5-7 SCU7 947 5MP7
.500 A5-8 A05-8 B5-8 05-8 5CU8 5!48 5NP8

.562 A5-9 A05-9 05-9 D5-9 5H9 5nP9

.625 A5- LO A05- 10 B5-10 05-10 9!10 5mPlo
.687 .- AD5-11 .. -. .. ..
.686 -. .. .. 5?U1 5nPll
.750 AS- 12 I&- 12 B5-12 05-12 9412 w 12

.234 .812 .. -. -- .. -. 5H13 5W 13

.156 .312 .067 A5-14 914 5MP14
.875 A05-14 B5-i4 05- i4 5CIJ14
.938 .- .. -. -- -- 5M15 5mP15
I 1.000 A5-16 A05-16 05-16 05-16 5W16 5H16 5MP]6
:.062 .. ADS- 17 .. -. .. .. e.

1.125 A5-iB AD5-i8 B5-18 05- i8 .- 5M1R 514Pls

1. :e7 .. AD5- i9 -. .. -- -.
1.250 A5-20 AD5-20 8;120 Os. -20 .. 5M20 ..
1.375 A5-22 A05-22 B5-22 05-22 .. 5H22 -.
1.500 A5-i4 A05-24 ES-24 05-24 9424 -.

;.750 A5-Z8 AJ35-2B B5-28 05-28 5M28 .-

2.000 -- .- -. .. 5M32 ..

.312 A6-S ma-f! 86-5 06-5 .. 6H5 -.

.375 A6-6 A06-6 06-6 06-6 6CU6 w -.
,438 A6. 7 AM-7 B6. ? 06-7 6CU7 6Pt7 --
.500 A6-e AD6-8 B6-a 06-e 6CU8 6M8 -.
.562 AA-9 A06-9 B6-3 36-3 -- 6U9 ..

.625 A6- 10 AD6-10 86-10 06-iO 6CU1O 6M1O --

.667 .. AM-ii B6-1: .. -. .. ..
.688 .- -. .- .- 6!41! -.
.750 A6-;2 A06- 12 Fli:12 X-12 6CJ12 6M1: ..
.812 .- .. -- -- -- 6H]3 --

.875 A6-14 AD6- 14 B6-14 D6- 14 6C3J14 6H!4 ..

1B7 .375 .281 .060 .. -. .- .. ..
. !N8 6n15
1.000 A6-16 AD6- 16 86-16 06-16 6a216 6M16 .-
1.125 A6-18 AM-18 B6-18 06-18 6CU18 6Mle .-
i.250 A6-20 AD6-20 %6-20 06-20 6CU20 6M20 ..

1.375 M-22 A06-22 B6-22 06-?2 6CU22 6n22 ..

1.500 A6-24 AM-24 86-24 06-24 6CU24 6n24 -.
1.750 A6-28 A06-2B 86-28 M-28 .. 6K28 .-
2.000 M-32 A06-32 B6-32 06-32 6U32 -.
2.250 . AM- 36 .. .. .- .. ..

2.500 A6.$o h6.40 06-40 iM-40 .- -. -.

3.000 A6-48 A06-4B B6-46 “ X-48 .. -- ..

.-
I I .438
.500
A8-7
A8- B
A08-7
bo8-8
88.7
B8-6
8CU7
8CUB
%7
ma .-
.-
.562 A8- 9 AD9-9 B8-9 8CU9 Bu9
I
I .625 A8- 10 AO8-10 88-:0 S~J 10 Bf410 ..
.688 -. .. .. 3CUI I Wll ..
I
I
, 75.J A&l? 408-1? 38-:: Scui : 9:: --
.312 .. .. .- Ecu 13 E/413 -.
I i
.375 AB. 14 AC8- 14 88.14 BCU14 &l]4 .-
.333 .- -- -. 8CU15 e/415 -.
:, IJy) A8.;6 AD8- :6 98-16 8CU16 W16 --
250 .500 .:75 .107
1.:25 AO-; e A38- 16 88-;8 9CU18 E2416 -.
:.:50 A6-2Z A08-ZG 98-:0 8CU:0 , W2: --
-.
I
I 8CU22 M22
I 1.375 A8.:Z A06-2? B8-22
Ah- ;4 A06-:4 88-;4 ecu24 : @t24 --
M-28 Ao8-:e 88-:8 acu29 W9 .-
A8- 12 32 B8- 12 8CU32 M32 -.
I
2.!300 Af)e.

1 I
(
2.500
3.300
i. 500
A8-40
M-w
AR- 56
ACIB-40
AOfL4fl
AOfI-56
B8-JO
B8-M
128-%
-.
-.
--
-.
..
-.
..
..
-.
 Downloaded from http://www.everyspec.com

.:

F!IL-STD-1759
10JULY 1979

TABLE II. Part numbers.

M4carlol . . . . . . . . . . . .

%tmclwffilch ..........
Shotrftmwm (9sl) tin . . . . . . . .

01a Al, c L&n

T
.12s .2P2 -20Z
.lM -2?1 -203
.2s0 .294 .204
.w .119- .094 .027 - .112 .2P\ -205
,111 .037 .115 .2?6 +4

.08 .2?1
I .502 .2?8 I
-207
-206
1
.IM
I .250
.11?
475
.Qla
.054 .04C .
MO .500 .JPB -208
.625 .VIO .2010

.
.79 .2912 :)0/:
.m .)?14
l.mo -2?16 .M14

T
2s0 .494 -404
.112 .49s

1T
.375 .W6 :26
.4)8 -4P7 .al
.500 .4P0 -408
T
12s .236 - . lM .0s4 - .625 .4?10 .4010
.261 M4 .750 -4P12 .4012
.81s .4V14 -4014
I.oco .4916 -4016
1.250 .4P20 -4020

I 1.s00 .49Z4 I -40?4

.5?$

T
.312 -s05
.175 .S?c .506
.410 .5$7 .507
.m .59s .608
.s25 .5910 .5010

.)54 .296 - ,234 .067 - .750 .5912 .50)2

328 .077 . S73 .5?14 -5014
l.mo .$9)i .5016
1.25G .5P20 .5023
1.500 . !?24 .M2*

-4?21 .5028

~. I 1.750
2.mo - SV32
I
-5032

.112 I .49s / .405

I 17s .696 -406
.438 .6P? -601
.5CQ .4P8 .400
.625 I -6?10 .bolc

.750 .69[2 .4012

.164 .154 . .281 .Om - .815 .$914 .WI*
. ]94 .092 I.000 -wit -4016
1.125 -6?18 -4011
I. 250 .6?20 -4020

1.315 .4?Z2 -6022

1.500 .6?24 -b024
1.750 -bP2B -4028
2.OW 4912 4022

.438 .Wr -m?

.500 -m -ma
. bzs -Wlo -Ulo
,750 -Ul? -m12
. 8?5 .@\4 -a14
.250 .107 .
.117 1.000 -@16 -s)16
1.250 -6920 .mo
1.5W .Wzt .mzd
1.7s0 - 89?8 -ws
I Z.000 -3932 -M32

722.4 ,
-.
 ●
Downloaded from http://www.everyspec.com

..

:41L-STD-1759
10 JULY 1979

SECTION723

RIVET-SOLIDUNIVERSAL
HEAD,
A286CORROSIONRESISTANT
STEEL
APPLICABLE
DOCUMENT:NAS1198

\
\

1IIIA
--

Shear strength
Material Protective finish
(psi) min

Cres A286 I Passivate 90,000

TABLE I. Rivet configuration Dash numbers.

Dia A L
c NAS1198
Length Dash no.
. .

.125 -2-2
,188 -2-3
.250 . -2-4
.312 -2-5
.062 .125 .027 .375 -2-6

.438 -2-7
,500 -2-8
,563 -2-9

. 773.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

—.
I

Dia A c L NAS1198
Length Dash no.

.188 -3-3
.250 -3-4
.312 -3-5
.375 -3-6
.438 -3-7
.094 .187 .040
.500 -3-8
.563 -3-9
.625 -3-1o
.688 -3-11
.750 -3-12

.250 -4-4
.312 -4-5
.375 -4-6
,438 -4-7
.500 -4-8

.563 -4-9
.625 -4-1o
.125 .250 .054 .688 -4-11
.750 -4-12
.813 -4-13

,875 -4-14
,938 -4-15
1,000 -4-16
1.125 -4-18
1.250 -4-20
0

.250 -5-4
.312 -5-5
.375 -5-6
.438 -5-7
*
,500 -5-8

.563 -5-9
.625 -5-1o
.156 .312 .067 ,688 -5-11
.750 -5-12
.813 -5-13

.875 -5-14
.938 -5-15
1,000 -5-16
1.125 -5-18
1.250 -5-20

723.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

Dia “A c L NAS 1198

Length Dash no.

.375 -6-6
.438 -6-7
s500 -6-8
.563 -6-9
.625 -6-10

,688 -6-11
.187 ,375 .080 .750 -6-12
,813 -6-13
.875 -6-14
.938 -6-15

1,000 -6-16
1.125 -6-18
1.250 -6-20

,375 -8-6
.438 -8-7
,500 -8-8
.563 -8-9
.625 -8-10

,688 -8-11
.250 “ .500 ,107 ,750 -8-12
.813 -8-13
.875 -8-14
.938 -8-15

1,000 -8-16
1.125 -8-18
1.250 -8-20 ‘
(

NOTE : Suggested shank length protrusion

1-1/4 to 1-1/3 times rivet diameter.

723.3
di
 Downloaded from http://www.everyspec.com

.~d
 Downloaded from http://www.everyspec.com

..

-.
MIL-STD-1759
10 JULY 1979

SECTION724

RIVET,
SOLID-UNIVERSAL
HEAD,AMS5737
APPLICABLEDOCUMENT: MS9403

r-lI\
\
\
J I
I t
/
1 /
\
\
I \
!
/ I

u
b’

Shear strength
Material Protective finish
(psi) min

lCres 15Cr-26Nil Not Specified I 90,000 I

TABLE I. Rivet configuration dash numbers.

D L
A B c MS9403
Di a length
Dash no.

,219
-066
.250 -067
.281 -068
.312 -069
, ()$1~ .179 - ,040 .141 .344 -070
.197
.375 -071
.406 -072
.438 -073
.469 -074
 Downloaded from http://www.everyspec.com

.-
MIL-STD-1759
10JULY 1979

TABLE I. Rivet configuration dash numbers. - Continued

D L
A B c MS9403
Dia Length
Dash no.

.250 -128
.281 -129
.. .312 -130
.344 -131
..375 -132

.406 -133
.438 -134
.469 -135
.500 -136
.531 -137
.125 .238 - .054 .188
.262 .562 -138
.594 -139
.625 -140
.636 -141
.688 -142

.719 -143
.750 -144
.781 -145
I
.812 -146 -
.844 -147
.312 -191
.344 -192
.375 -193
.406 -194
.438 -195

.469 -196
.500 -197
.156 .296 - .067 .234 .531 -198
.328 .562 -199
.594 -200

.625 -201
.656 -202
.688 -203 ●

.719 -204
,
.344 -253
.375 -254
.406 -255
.438 -256
. 188 .356 - .080 .261 .469 -257
.394
.500 -258
,531 -259
.562 -260
.594 -261

724.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION725

RIVET,SOLID,
UNIVERSALHEAD,AMS7229
APPLICABLEDOCUMENT: AN123151THRU AN123300

Shear strength
Material Protective finish
(psi) min

Cres 18Cr-llNi [ Not Specified I Not Specified

TABLE I. Rivet configuration Dart numbers.

L
A B c Part no.
Length

.188 AN123152
.219 AN123159
.250 AN123153
.281 AN123160
.312 AN123154

.062 .125 .027 .112 .344 AN123161

.375 AN123155
.406 AN123162
,438 AN123156
.469 AN123163

.500 AN123157

725.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration part numbers. - Continued

L
A B c Part no.
D!a Length

.250 AN123169
.281 AN123165
.312 AN123170
.344 AN123166
.375 AN123171

.406 Ati123167
.438 AN123172
.469 AN123179
.094 .188 .040 .169 .500 AN123173
.531 AN123180

.562 AN]23174

.594 AN123181
.625 AN123175
.656 AN123182
.688 AN123183

.719 I AN123199
-
.312 AN123186
.344 AH123249
.375 AN123187
,406 AN123250
.438 AN123188

.469 AN123251
.125 .259 .054 .225 .500 AN123189
.531 AN123252
.562 AN123190
.594 AN123253

,625 AN123191
.656 AN123254
.688 AN123263
,719 AN123264

.344 AN123291
,375 AN123203
,406 AN123292
.438 AN123204
.469 AN123293

.500 AN123205
.156 .312 .067 .281 .531 AN123294
.562 AN123206
.594 AN123295
.625 AN123207

.656 AN123296
.688 AN123297
.719 AN123298

.438 AN123220
.188 .375 .080 .338 .500 AN123221
.562 A)i123222
,625 AN123223

725,2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION726

RIVET,
SOLID,
UNIVERSALHEAD,AMS7232
APPLICABLEDOCUMENT: AN123301THRU AN123450

t
I
1

?
/
-D
L“

Material Protective finish Shear strength

(psi) min

Cres15.5Cr-EIFe I Not specified I Not specified

TABLE I. Rivet configuration part numbers.

D A B c L Part no.
Dia

.188 AN123302
.219 AN123309
.250 AN123303
.281 AN12331O
,062 .125 .027 .112 .312 AN123304
●344 AN123311
.375 AN123305
.406 AN1233?2
.438 AN123306
.469 AN123313
.500 AN123307 ~

726.1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE 1. Rivet configuration part numbers.- Continued

D
A B c L Part no.
Dia

.250 AN123319
.281 AN123315
.312 AN123320
.344 AN123316
.375 AN123321
.406 AN123317
● 094 .188 ● 040 .169 ,438 PN123322
.469 AN123329
●500 AN123323
.531 AN123330
.562 AN123324
●594 AN123331
.625 AN123325
.656 AN123332
,688 AN123333
.719 /W123349
.312 AN123336
344● AN123399
.375 AN123337 ...
.406 AN123400
.438 ,4N123338
.469 AN123401
.125 .250 ● 054 .225 *500 AN123339
.531 AN123402
.562 AN123340
,594 AN123403
.625 AN123341
.656 AN123404
.688 AN123413
.719 AN123414

344● AN123441
.375 AN123353
.406 AN123442
.438 AN123354
.469 AN123443
.156 .312 .067 .281 ●500 AN123355
.531 AN123444
.562 AN123356
●594 AN123445
.625 AN123357
,656 AN123446
.688 AN123447
.719 AN123448

.438 AN123370
.188 .375 .080 .338 ●500 AN?23371
.562 AN123372
,625 AN123373

726.2
 Downloaded from http://www.everyspec.com

..

~!IL.sTD-1759
10JULY 1979

SECTION727

RIVET,
TITANIUM,
BIMETAL,95KSIFW
100°FULLFLUSH,CROWN HEAD,TYPEII
APPLICABLEDOCUMENT:

lib-
-

Shear strength
Material Protective finish (psi) min

Body : None . 95,000

Titanium
alloy 6AL-4V
Tail: None 50,000
Titanium
alloy 45-Cb

727.1
 Downloaded from http://www.everyspec.com

.:

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration Dash numbers.

.

Grip range L M83459/2

D Al H G
Min Flax Length Dash number

.125 .126 .156 .330 -5-3

.156 .157 .187 .361 -5-3R

.187 ●188 .218 .392 -5-4

.218 .219 .250 .423 -5-4R

.250 .251 .281 .455 -5-5

.281 .282 .312 .486 -5-5R

.312 .313 .343 .517 -5-6

.343 .344 .375 .548 -5-6R

.375 .376 .406 .580 -5-7

.406 .407 .437 .611 -5-7R

.437 .438 .468 .642 -5-8 -

.468 .469 .500 .673 -5-8R
.164 .271 .051
.500 .501 .531 .705 -5-9
.531 .532 .562 .736 -5-9R

.562 .563 .593 .767 -5-1o

.593 .594 .625 .798 -5-1OR

.625 .626 .656 .830 -5-1]

.656 .657 .687 .861 -5-~~R

.687 .688 .718 .892 -5-12

.718 .719 .750 .923 -5-12R

.750 .751 .781 .955 -5-13

.781 .782 .812 .986 -5-13R

.812 .813 .843 1.017 -5-14

.843 ●844 .875 1.048 -5-14R

.875 .876 .906 1.080 -5-15

.906 .907 .937 1.111 -5-i5R

.937 .938 .968 1.142 -5-16

●968 .969 1.000 1.173 -5-16R
-

727.2
 Downloaded from http://www.everyspec.com

.:

IIIL-STD-1759
10 JULY 1979

---- -

x
.
1,

I -’
u
o
z
{

. . . . . . . . . . .

t 1

I
L

72?.3
 Downloaded from http://www.everyspec.com

.:

.
 Downloaded from http://www.everyspec.com

---
MIL-STD-1759
10 JULY 1979

SECTION728

RIVET,
TITANIUM,
ElMETAL,95KSIFsuq
PROTRUDINGHEAD,TYPEI ~
APPLICABLEDOCUMENT: MIL-R-B3459/l

H
1

Shear strength
Material Protective finish (psi) min

None 95,000
Body: Titdnium
alloy 6AL-4V

None 50,000
Tail: Titanium
alloy 45-c~

728.1
 Downloaded from http://www.everyspec.com

..

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers.

Grip range L
D A H G
-?Ti7 -im7 Length

.093 ,094 .125 .298 -5-2R

.125 .126 .156 ● 330 -5-3

.156 .157 .187 .361 -5-3R

.187 .188 .218 .392 -5-4

.218 .219 .250 .423 -5-4R

e250 .251 .281 ●455 -5-5

.281 .282 .312 .486 -5-5R

.312 .313 .343 .517 -5-6

.235 ●049 .343 ●344 ●375 .548 -5-6R

.164 .249 .055 375 .376 .406 -5-7
● .580

.406 ●407 .437 .611 -5-7R

.437 .438 .468 .642 -5-8

.468 .469 ●500 .673 -5-8R

●500 .501 .531 ●705 -5-9

.531 .532 .562 .736 -5-9R

.562 .563 .593 .767 -5-1o

●593 ●594 .625 ,798 -5-IOR

.625 .626 .656 .830 -5-11

.656 .657 .687 .861 -5-n R

.687 .688 .718 .892 -5-12
.

.718 .719 .750 .923 -5-12R

.750 .751 .781 .955 -5-13

.781 .782 .812 .986 -5-13R

.812 .813 .843 1.017 -5-14

.843 .844 .875 1.048 -5-14R

.875 .876 .906 1.080 -5-15

.906 .907 .937 1.111 -5-15R

.937 .!?28 ,968 1.142 -5-16

.968 .969 1.000 1.173 -5-16R

I

728.2
 Downloaded from http://www.everyspec.com

- “.

MIL-S?-D-1759
10 JULY 1979

-.

-- -- - -

u
. .

-’---

728.3

Q.\I
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

u
. .

m
0 m
.

. .

<

Cu
r-l
.

728.4

.
.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10JULY 1979

SECTION729

RIVET,
TITANIUM,
BIMETAL,
9SKSIFsu.
100°REDUCEDFLUSHCROWN HEAD TYPE Ill
APPLICABLEDOCUMENT: M[L-R-83459/3

(y’1. ,,
d‘L
b
100°

‘7 D

J Ii

Shear strength
Material Protective finish (psi) min
I I
I I
I alloy
Body: Titanium I
6AL-4V
None I 95,000
I

Tail: Titanium None 50,000

alloy 45-Cb 3

77Q. 1
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers.

D Al H Grip range L M83459/3

G
Min Max Length Dash no.

.125 .126 .156 .330 -5-3

.156 ●157 .187 .361 -5-3R

.187 .188 .218 .392 -5-4

.218 .219 .250 .423 -5-4R .

.250 .251 .281 .455 -5-5

.281 .282 .312 .486 -5-5R

.312 .313 .343 .517 -5-6

.343 .344 .375 .548 -5-6R

.375 .376 .406 .580 -5-7

.164 .230 .034 .406 .407 .437 .611 -5-7R

.437 .438 .468 .642 -5-8

.468 .469 .500 .673 -5-8R

.500 .501 .531 .705 -5-9

.531 .532 .562 .736 -5-9R

.562 .563 .593 .767 -5-1o

.593 .594 .625 .798 -5-1OR

.625 .626 .656 .830 -5-11

.656 .657 .687 .861 -5-llR

.687 ●688 .718 .89? -5_~2
●

.718 .719 .750 .923 -5-12R

.750 .751 .781 .955 -5-13

.781 .782 .812 .986 -5-13R

.812 .813 .843 1.017 -5-14

.843 .844 .875 1.048 -5-14R

.875 .876 .906 1.080 -5-15

.906 .907 .937 1.111 -5-]5R

,937 i ,~j: ,968 1,142 -5-16
, (
.966 I .969 1.000 1.175 -5-~6R
 Downloaded from http://www.everyspec.com

...-
HIL-STD-1759
10 JULY 1979

TABLE 1. Rivet configuration dash numbers. - Continued

——
M83459/3
0
D4sII no.

.125 .126 ! .156 .):7 -6-3 ,156 .1s? .l&17 .423 1 -E -3R
.187 .188 .216 .455 ‘ -b-4
. )56 .157 \ .]87 [ ,378 -6-3R
.187 .188 j .218 .410 .6A .210 .215 ‘ .252 .486 -E.-4U
.250 .2s1 .2s1 .51: ! -b-5
A
.219 ~ .250
I .441 -6-d8 !
.218
.250 .251 , .281 .412 -6-5 .201 .282 .312 .548 .lj-5R
1 .312 .J13 ; .343 .550 : -c- 6
-b-5R t
.281 .282 i .312 . S03
-6-6 .343 .344 375 .61i -~-6R
.312 .313 , .343 .s35
i .375 .376 , .406 .642 -lj-7
.343 .344 ; .375 . S66 -6-6R
.375 .3?6 .406 .557 -6-7 .406 .407 ,437 .673 ‘
I .437 .438 i .466 .7C5 ,
I
,406 .407 ‘ .437 .62& -6-7Q .250 ‘ .373 ! .06c
.437 ,438 ; .466 : 66s -64 .466 .469 .5X ‘ .736 -e+R
I I .500 .50; ‘ 531 .761 -%9
.468 469 \ .500 : .69: -6-6R I I
.:89 .046 .500 .501 .53: ~ .122 -6-9 1 I .53! .s32 .362 .798 -~-9R
I I .56.2 .563 .s93 .632 , -k.-io
.531 .532 ~ .562 ; .753 .6.;2 I
.785 , .593 .594 .625 .k61 !
.562 .563 : .S93 -6-i C
I 1 .625 .626 .656 .892
.593 .594 ‘ ,625 ‘ .816 -6_i~R
I 656 ~ .657 ; .687 .923
.625 .626 .656 .047 -6-1:
I ,6e7 ; .688 .116 .955
! .(-I:P I
.656 .657 .667 .976 : I .5-12R
.687 .668 .;:6‘ .913 -6*:2 .9E6
I
I ! 1.0i7 , -C-13
,7!9 ?59 .94; .6-;2a 1
.78; .S72 .6_i3 .,
.,:.,
!
.7U .C; ; 1.(x%
I
I .612 .813 .843 !.0!50
.7e: 1 .7t32 .8!2 ‘ 1.003 \ .6_:3& ,
, .Oii , .8i3 8; 3 1.G35 ‘ -6-1: I .5;3 :
.-. :
1
.844 ,:75 1.;1.
a{. .61t 326 i i.l?
I ;;;; ~ .844 ,875 1.066 -f-:da
.:-:5k
I .876 .906 :.09? -6-15
‘t
.+-.
I .C-isa
i .906 J .907 .?37 1.128 ,
.- .7.
.0-)6

1. Joc 1.i91 .6_i6R I I ( ( I

i
#

.610 I .~?-$ “
.187 .188 .250 . S02 -1>: .253 .251 .312
.312 .315 .375 .672 I -12-6
I
I
.250 .251 .312 .S65 - I*: .375 .534 .!J77
.i~-;
.312 .313 .375 .627 .104 .37s .376 .437 .735
.437 .43C SW .797 -12+ I
.375 .376 .437 .690 -]0-7
.437 .152 -10-8 .500 .50) .562 .860 -12-9
.438 .500
.312 .441 .067 .562 .563 .62S .922 .12-10
.500 .501 .562 .815 -I(L9
.562 .563 .625 .877 -1o-1o

.625 .626 .687 .940 - 1(.-1 !

.687 .68B .759 1 ~n2 .1(-12
I
.750 .751 .812 :.065 -lG-13
.812 .813 .875 1.127 -]0-14

.8?5 .876 .937 1.190 -10-1:

.937 .938 1.000 L.252 . 10-i6
——

729*3 A
Downloaded from http://www.everyspec.com

.
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION801

RIVET,SPLIT-OVAL
HEAD
APPLICABLEDOCIJMEifT:
MS35684.MS35685

G-

T-j--(
—- t
; i-if ‘-r

l-- F

Footnotes Part numbers Material Shear strength

(psi) min

~/ MS35685 Brass 35,000

+ dash no, composition
260 or 270

q !4S35684 Carbon stee’ 32,000

+ dash no. C1OO5 thru
cl022

TABLE 1. Part numbers.

D“
Nominal .125 .140 .187
.
size
A
Head .224 .318 .350

Ii
Head .037 .052
thickness
S1OK idth slot width

7
.Slot width slot ~/ SiOt
slot
nl-
T
L At At At At At
depth depth or depth
Length base point base point ~ base point
F El F
G J G J G J

.C65 .120 .219

.250 .040 .052 .219 -1 .050 .073 .219 -9
.312 .040 .057 .281 -2 .050 ,078 .281 -10 .065 .125 .281
.375 .040 .057 .312 -3 .050 .081 .328 -11 .065 .127 .312
.438 .040 .057 .312 .050 .083 ,344 -12 .065 .130 .375
.500 .040 . 0s7 .312 :: .052 .077 .391 -13 .068 .133 .437
.562 .040 .057 .312 -6 .052 .077 .391 -14 .068 .133 .437
.625 ●040 .057 .312 -7 .052 .077 .391 -15 .068 .133 .437
.7s0 .040 .057 .312 -8 .052 .077 .391 -16 .068 .133 .437

801A1
.
Downloaded from http://www.everyspec.com

!n )
 Downloaded from http://www.everyspec.com

.
.

MIL-STD-1759
10JULY 1979

SECTION901

RIVET-TUBULAR,
150°FLAT COUNTERSUNK HEAD
APPLICABLEDOCUMENT: MS16536

1o--BI
W--’-l A

4$ ‘+’
\#

OPTIONAL i ‘1

Material Protective finish Shear strength

(psi) min

32,000
Carbon steel
C1OO5 thru C1022
Cadmium plate
I
Brass composition Oxide or black 35,000
260 or 270 finish or
quarter hard nickel plate

2117-T4 Anodize or chemical 26,000

Aluminum 4
surface treatment
alloy None 24,000
5056-H32

TABLE 1. Rivet configuration.

I Nominal size .123

.
.146
1

Max Mln Max Min Max

Head diameter T -- .303 -- ;367
Head thickness H -- .038 -- .045 -- .051
Straight hole D .090 -- .105 -- .139
Taper at bottom of hole El ‘-
.079 .085 .110
Taper at end of rivet E2 .0;; .li; -- .Jii
Hole depth (taPer) “G .0;2 .- .1;; -- .135 --
— i
Hole depth (straight) nom C ,094
Clinch allowance ,074
b —

Qnl 1
 Downloaded from http://www.everyspec.com
.

.:..

MLL-STD-1759
10 JULY 1979

TABLE II. MS16536 l)ashnumbers.

.

Carbon Aluminum Carbon

L Brass L Brass ,
steel alloy steel J
Length ‘ Dash number Length Dash number
4

Nominal size .123 Nominal size .188 .

.250 -1 -16 -31 .250 -151 -168

.281 -2 -17 -32 “ .281 -152 -169
.312 -3 -18 -33 .312 -153 -170
.344 -4 -19 -34 .344 -154 -171
.375 -5 -20 -35 .375 -155 -172

.406 -6 -21 -36 .406 -156 -173

.438 -7 -22 -37 .438 -157 -174
.469 -8 -23 -38 .469 -158 -175
.500 -9 -24 -39 ●500 -159 -176
.531 -lo -25 -40 .531 -160 -177

.562 -11 -26 -41 .562 -161 -178

●594 -12 -27 -42 .594 -162 -179
.625 -13 -28 -43 .625 -163 -180
.688 -14 -29 -44 .656 -164 -181
.750 -15 -30 -45 .688 -165 -182
.
.719 -166 -183
.750 -167 -184

Nominal size .146

e250 -76 -91 -106

.281 -77 -92 -107
.312 -78 -93 -108
●344 -79 -94 -109
.375 -80 -95 -110

.406 -81 -96 -111

.438 -82 -97 -112
.469 -83 -98 -113
●500 -84 -99 -114
.531 -85 -1oo -115

.562 -86 -101 -116

.594 -87 -102 -117
.625 -88 -103 -118
.688 -89 -104 -119
.750 -90 -105 -120

901.2
 Downloaded from http://www.everyspec.com

MIL-STD-1759
10 JULY 1979

SECTION902

RIVET,
TUBULAR-FLAT
HEAD
APPLICABLEDOCUMENT: MS51942

l:l-L

Shear strength
Material Protective finish
(psi) min

Carbon steel None 32,000

C1OO5 thru
C1022

Brass None 35,000

composition
260 or 270
quarter hard

902.1
 Downloaded from http://www.everyspec.com
.

MIL-STD-1759
10 JULY 1979

TABLE I. Rivet configuration dash numbers.

Nominal size A .123 .146 .188

.- .223 -- .317 -- .381

Head diameter R
.041 -- .052 -- .067
Head thickness H ‘- .141
-- 090 -- ●107 --
Straight hole D ●

.079 ‘- .091 -- .120 --

Taper at bottom of hole ‘1 -- .095 -- .112 -- .145
Taper at end of rivet ‘2
.082 ‘- 104 ‘- .135 --
Hole depth (taper) G
.104 -- 135 -- .166
‘-
●

Hole depth (straight) C

Clinch allowance .074 .088 ● 120

L

L Steel Brass
Length MS51942 Dash number MS51942 Dash number
.123 .146 ,188 .123 .146 .188

.094 -1 - - -50 - -
.125 -2 - - -51 - -
.156 -3 - - -52 - -
. -4 -17 - -53 -66 -
.187
.219 -5 -18 - -54 -67 -

.250 -6 -19 -32 -55 -68 -

.281 -33 -69 -
-i -;1 -34 -57 -70 -84
.312
.375 -9 “22 -35 -58 -71 -
●500 -24 -37 -73 -86

.562 -25 -38 -74 -

.625 -26 -39 -75 -

902.2

P no
—.
Downloaded from http://www.everyspec.com

- MIL-STD-1759
10 JULY 1979

SECTION903

RIVET-TUBULAR,
OVAL HEAD
APPLICABLEDOCUMENT: MS16535

+BI

lG t-l

OPTIONAL k,

Shear strength
Material Protective finish
(psi) min

Carbon steel Cadmium plate 32,000

C1OO5 thru CI022

Brass composition Oxide or black 35,000

260 or 270 finish or
quarter hard nickel plate

Anodize or chemical
Aluminum 2117-T4 26,000
surface treatment 4
alloy
L5056-H32 None ?4.000

Nickel copper None 49,000

alloy (Monel)

;opper type S None 24,000

TABLE 1. Rivet configuration.

“Nominal size A I .061 .089 .123 .146 .188

Head diameter B
H
Min I Max Min I Max Mi n Max Min Max Min Max
Head thickness
Straight hole D -. .114 -- .152 -- .223 -- .239 -- .318
Tdl)(?r at bottom of hole El -- .019 -. .026 -. .038 -- .045 -- .065
Taper at end of rivet E2 -. .044 -. .068 -- .090 -- .107 -- .141
Hole deDth (taDer) G .032 -- .!350 -- .079 -- .085 -- 110 --
.046 .- .068 .- ,095 -- .l]~ -- ,145
Hole depth (straignt) nom C .gi; -- ,057 -- . !)82 -- .104 -- 125 --

Clinch allowance ,094 .12E ‘ .155

.074 .088 .125

903.1
 Downloaded from http://www.everyspec.com

=.

MIL-STD-1759
10 JULY 1979

TABLE 11. MS16535 Dash numbers.

Nickel Nickel
Aluminum Aluminum
L ::gy Brass copper CoOper :;::yf’ Brass Copper Copper
alloy alloy
kngth . alloy lekgth , allov
Dash number 0 sh u e
Nominal size .061 Nominal ;izen.!!6r

.094 -1 -11 -21 -31 -41 .125 -211 -228 -245 -262 -279
.125 -2 -12 -22 -32 -42 .156 -212 -229 -246 -263 -280
.156 -13 -23 -33 -43 .188 -213 -230 -247 -264 -281
.188 :: -]4 -24 - ~~ -44 .219 -214 -231 -248 -265 -282
.219 -5 -15 -25 -35 -45 .250 -215 -232 -249 -266 -283

.250 -6 -16 .26 -36 -46 .281 -216 -233 -250 -267 -284
.281 -7 -17 -27 -37 -47 .312 -217 -234 -2s1 -268 -285
.312 -18 -28 -38 -48 .344 -218 -235 -252 -269 -286
.344 :: -19 -29 -39 -49 .375 -219 -236 -253 -270 -287
.375 -10 -20 -30 -40 -50 .406 -220 -237 -254 -271 -288

Nominal size .089 .438 -221 -238 -255 -272 -289

.469 -222 -239 -256 -273 -290
.094 -51 -63 -75 -87 -99 .500 -223 -240 -257 -274 -291
.125 -52 -64 -76 -88 -100 .531 -224 -241 -258 -275 -292
.156 -53 -65 -77 -89 -101 .562 -225 -242 -259 -276 -293
.188 -54 -66 -78 -90 -102
.219 -55 -67 -79 -91 -103 .594 -226 -243 -260 -277 -294
.625 -227 -244 -261 -278 -295
.250 -56 -68 -80 -92 -104
,281 -57 -69 -81 -93 -105 ----
.312 -58 -70 -82 -94 -106
.344 -59 -71 -83 -95 -107 Nominal size .188
.375 -60 -72 -84 -96 -108
.188 -296 -317 -338 -359 -380
.438 -61 -73 -85 -97 -109 .219 -297 -318 -339 -360 -381
.500 -62 -74 -86 -98 -110 .250 -298 -319 -340 -361 -382
.531 - - - -401 - .281 -299 -320 -341 -362 -383
.312 -300 -321 -342 -362 -384
Nominal size .123
.344 -301 -322 -343 -364 -385
.094 -111 -131 -151 -171 -191 .375 -302 -323 -344 -365 -386
.125 -112 -132 -152 -172 -192 .406 -303 -324 -345 -36I5 -387
.156 -113 -133 -153 -173 -193 .438 -304 -325 -346 -367 -388
.188 -114 -134 -154 -174 -194 .469 -305 -326 -347 -368 -389
.219 -115 -135 -155 -175 -195
.500 -306 -327 -348 -369 -390
.250 -116 -136 -156 -176 -196 .531 -307 -328 -349 -370 -391
.281 -117 -137 -157 -177 -197 .562 -308 -329 -350 -371 -392
.312 -118 -138 -158 -178 -198 .594 -309 -330 -351 -372 -393
.344 -119 -139 -159 -179 -199 .625 -310 -331 -352 -373 -394
.375 -120 -140 -160 -180 -200
.656 -311 -332 -353 -374 -395
.406 -121 -141 -161 -181 -201 .688 -312 -333 -354 -375 -396
.438 -122 -142 -162 -182 -202 .719 -313 -334 -355 -376 -397
.469 -123 -143 -163 -183 -203 .750 -314 ’335 -356 -377 -398
.500 -124 -144 -164 -184 -204 .875 -315 -336 -357 -378 -399
.531 -125 -145 -165 -185 -205
1.000 -316 -33? -358 -379 -400
.562 -126 -146 -166 -186 -206
.594 -127 -147 -167 -187 -207
.625 -128 -148 -168 -189 -208
.688 -129 -149 -169 -189 -209
.750 -130 -150 -170 -190 -210
-

903.2
-n Xi
 Downloaded from http://www.everyspec.com

>..
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL
INSTRUCTIONS This form is provided to solicit beneficial comments which may improve this document and
enhance its use. DoD contractors, government activities, manufacturers, vendors, or other pros; .ctive u=~rs of
the document are invited to submit comments to the government. Fold on lines on reverse side, staple in coI ner,
and send to preparing activity. Attach any pertinent data which may be of use in improving th]s document, If
there are additional papers, attach to form and place both in an envelope addressed to prepming activity. A
response will be provided to the submitter, when name and address is provided, within 30 days indicating that
the 1426 was received and when any appropriate action on it will be completed.
NOTE: This form shall not be used to submit requests for waivers, deviations or ckrification of specification
requirements on current contracts. Comments submitted on this form do not constitute or imply authorization
to waive any portion of the referenced document(s) or to amend contractual requirements.
)OCUMEhJT IDENTIFIER (,’Vumber) AND TITLE

MI1.-STD-l759 RIVETS AND RIVET TYPE FASTENFRS. PRFFF~F~ FOR f)FW~ OF

JAME OF ORGANIZATION ANO ADDRESS OF SUSMITTER

3 VENDOR O USER n MANUFACTURER

@ HAS ANY PART OF THE DOCUMENT CREATED PROBLEMS OR REQUIRED INTERPRETATION IN PROCUREMENT

SE? @ IS ANY PART OF IT TOO RIGID. RESTRICTIVE. LOOSF OR AMBIGUOUS> PLEASE EXPLAIN BELOW.

A, GIVE PA RAG RAPF4 NUMBER AND WORDING

B. RECOMMENDED WORDING CHANGE

C. REASON FOR RECOMMENDED CHANGE(S)

. REh4ARKs

JBMIT 7%D BY (Prtnted or typed name ana addmbt - 0p fW2nal) TELEPHONE NC

DATE
I

a- -- —.. . .a -

m 1 ‘m” 1426 OCT 76

EDITION OF 1 JAN 72 WILL BE USED UNTIL EXHAUSTED.
 Downloaded from http://www.everyspec.com

-:.

Fo Lo

●O~AGE AND FEES PAID

Uaw
m
OFFICIAL 8USINE=
PENALTY FOR PRIVATE USE $3G0

Commander
Aeronautical Systems Division (AFSC)
ATTN : ASD/ENESS
Wright-Patterson AFB, OH 45433

FOLD