ConneXium

TCSESM Managed Switch

Installation Manual

Fault Fault
+24V(P1) 0V 0V +24V(P2) +24V(P1) 0V 0V +24V(P2)

P Fault P Fault
LNK ACT Stand by RM Stand by RM
RM RM
Stand by ON ON
Stand by

USB USB

MAC-Address
MAC-Address

1
IP-ADDRESS

IP-ADDRESS
V.24 V.24

LNK

3 4 1
ACT
LNK
LNK ACT
cable positions if DHCP Option 82 is enabled.

5 6 11 12
UNINTENDED OPERATION Do not change

2
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

ACT
Check user manual before servicing.
WARNING

Check user manual before servicing.

LNK
WARNING

2 7 8 13 14 3
ACT
LNK

9 10 15 16 4
ACT

ConneXium Switch ConneXium Switch

TCSESM163F2CU0/CS0 TCSESM043F23F0

Fault Fault
+24V(P1) 0V 0V +24V(P2) +24V(P1) 0V 0V +24V(P2)

3 4

P Fault P Fault
LNK ACT Stand by RM LNK ACTStand by RM
RM RM
5 6 Stand by ON ON
Stand by

USB USB
MAC-Address

MAC-Address

1 1
7 8
IP-ADDRESS

IP-ADDRESS

9 10 V.24 V.24

11 12

LNK ACT LNK ACT

cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

13 14 19 20 3 4
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change
Check user manual before servicing.
WARNING

Check user manual before servicing.

WARNING

2 15 16 21 22 2 5 6

17 18 23 24 7 8

ConneXium Switch ConneXium Switch

TCSESM243F2CU0 TCSESM083F2CU0/CS0/CX0
31007118.08

www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical
characteristics of the performance of the products contained herein. This documentation is not
intended as a substitute for and is not to be used for determining suitability or reliability of these
products for specific user applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products with respect to the
relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or
subsidiaries shall be responsible or liable for misuse of the information contained herein. If you
have any suggestions for improvements or amendments or have found errors in this publication,
please notify us.

You agree not to reproduce, other than for your own personal, noncommercial use, all or part of
this document on any medium whatsoever without permission of Schneider Electric, given in
writing. You also agree not to establish any hypertext links to this document or its content.
Schneider Electric does not grant any right or license for the personal and noncommercial use
of the document or its content, except for a non-exclusive license to consult it on an "as is" basis,
at your own risk. All other rights are reserved.

All pertinent state, regional, and local safety regulations must be observed when installing and
using this product. For reasons of safety and to help ensure compliance with documented
system data, only the manufacturer must perform repairs to components.

When devices are used for applications with technical safety requirements, the relevant
instructions must be followed.

Failure to use Schneider Electric software or approved software with our hardware products may
result in injury, harm, or improper operating results.

Failure to observe this information can result in injury or equipment damage.

© 2018 Schneider Electric. All Rights Reserved.

31007118- 02/2018
Contents

About this Manual 4

Key 6

Safety instructions 7

1 Description 18
1.1 General device description 18
1.2 Device versions 19
1.2.1 Device versions 19
1.2.2 Examples of switch versions 20

2 Assembly and start-up 24

2.1 Installing the device 24
2.1.1 Overview of installation 24
2.1.2 Unpacking and checking 25
2.1.3 Insert data in label area 25
2.1.4 Installing the SFP transceivers (optional) 25
2.1.5 Adjust DIP switch settings 26
2.1.6 Connecting the terminal blocks for supply voltage and
signal contact 26
2.1.7 Installing the device on the DIN rail, grounding 28
2.1.8 Dimension drawings 29
2.1.9 Installing the terminal block, start-up procedure 30
2.1.10 Connecting the data lines 30
2.2 Display elements 32
2.3 Basic set-up 34
2.4 Disassembly 36

3 Technical data 37

31007118 - 02/2018 3
About this Manual
Validity Note
The technical characteristics of the devices described in this document also
appear online. To access this information online:

Step Action
1 Go to the Schneider Electric home page www.schneider-electric.com .
2 In the Search box type the reference of a product or the name of a product range.
 Do not include blank spaces in the reference or product range.
 To get information on grouping similar modules, use asterisks (* ).
3 If you entered a reference, go to the Product Datasheets search results and click on the
reference that interests you. If you entered the name of a product range, go to the
Product Ranges search results and click on the product range that interests you.
4 If more than one reference appears in the Products search results, click on the
reference that interests you.
5 Depending on the size of your screen, you may need to scroll down to see the data
sheet.
6 To save or print a data sheet as a .pdf file, click Download XXX product datasheet.

The characteristics that are presented in this manual should be the same as
those characteristics that appear online. In line with our policy of constant
improvement, we may revise content over time to improve clarity and
accuracy. If you see a difference between the manual and online information,
use the online information as your reference.

Related Documents

Title Reference Number

ConneXium TCSESM, TCSESM-E Managed Switch 31007126
Redundancy Configuration User Manual
ConneXium TCSESM, TCSESM-E Managed Switch 31007122
Basic Configuration User Manual
ConneXium TCSESM, TCSESM-E Managed Switch 31007130
Command Line Interface Reference Manual
ConneXium TCSESM, TCSESM-E Managed Switch EIO0000000482
Web-based Interface Reference Manual
ConneXium TCSESM Managed Switch 31007118
Installation Manual
ConneXium TCSESM-E Extended Managed Switch EIO0000000529
Installation Manual

You can download these technical publications and other technical

information from our website at
http://www.schneider-electric.com/ww/en/download.

4 31007118 - 02/2018
Note: The Glossary is located in the Reference Manual “Command Line
Interface”.

The “Web-based Interface” reference manual contains detailed information

on using the Web interface to operate the individual functions of the device.

The “Command Line Interface” reference manual contains detailed

information on using the Command Line Interface to operate the individual
functions of the device.

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you
need to install the device.

The “Basic Configuration” user manual contains the information you need to
start operating the device. It takes you step by step from the first startup
operation through to the basic settings for operation in your environment.

The “Redundancy Configuration” user manual contains the information you

need to select a suitable redundancy procedure and configure that
procedure.

31007118 - 02/2018 5
Key
The symbols used in this manual have the following meanings:

 Listing
 Work step
 Subheading

6 31007118 - 02/2018
Safety instructions
 Important Information

Notice: Read these instructions carefully, and look at the equipment to

become familiar with the device before trying to install, operate, or
maintain it. The following special messages may appear throughout this
documentation or on the equipment to warn of potential hazards or to call
attention to information that clarifies or simplifies a procedure.

The additional of this symbol to a "Danger" or "Warning" safety

label indicates that an electrical hazard exists, which will result
in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.

DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
can result in death or serious injury.

CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury.

NOTICE
NOTICE is used to address practices not related to physical injury.

31007118 - 02/2018 7
 PLEASE NOTE: Electrical equipment must be installed, operated,
serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences
arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the
construction and operation of electrical equipment and its installation, and
has received safety training to recognize and avoid the hazards involved.

 Before you begin

Do not use this product on machinery lacking effective point-of-operation
guarding. Lack of effective point-of-operation guarding on a machine can
result in serious injury to the operator of that machine.

WARNING
UNGUARDED EQUIPMENT
 Do not use this software and related automation equipment on
equipment which does not have point-of-operation protection.
 Do not reach into machinery during operation.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

This automation equipment and related software is used to control a

variety of industrial processes. The type or model of automation
equipment suitable for each application will vary depending on factors
such as the control function required, degree of protection required,
production methods, unusual conditions, government regulations, etc. In
some applications, more than one processor may be required, as when
backup redundancy is needed.
Only you, the user, machine builder or system integrator can be aware of
all the conditions and factors present during setup, operation, and
maintenance of the machine and, therefore, can determine the
automation equipment and the related safeties and interlocks which can
be properly used. When selecting automation and control equipment and
related software for a particular application, you should refer to the
applicable local and national standards and regulations. The National
Safety Council's Accident Prevention Manual (nationally recognized in the
United States of America) also provides much useful information.

8 31007118 - 02/2018
 In some applications, such as packaging machinery, additional operator
protection such as point-of-operation guarding must be provided. This is
necessary if the operator's hands and other parts of the body are free to
enter the pinch points or other hazardous areas and serious injury can
occur. Software products alone cannot protect an operator from injury.
For this reason the software cannot be substituted for or take the place of
point-of-operation protection.
Ensure that appropriate safeties and mechanical/electrical interlocks
related to point-of-operation protection have been installed and are
operational before placing the equipment into service. All interlocks and
safeties related to point-of-operation protection must be coordinated with
the related automation equipment and software programming.

Note: Coordination of safeties and mechanical/electrical interlocks for

point-of-operation protection is outside the scope of the Function Block
Library, System User Guide, or other implementation referenced in this
documentation.

 Start-up and test

Before using electrical control and automation equipment for regular
operation after installation, the system should be given a start-up test by
qualified personnel to verify correct operation of the equipment. It is
important that arrangements for such a check be made and that enough
time is allowed to perform complete and satisfactory testing.

CAUTION
EQUIPMENT OPERATION HAZARD
 Verify that all installation and set up procedures have been completed.
 Before operational tests are performed, remove all blocks or other
temporary holding means used for shipment from all component
devices.
 Remove tools, meters, and debris from equipment.

Failure to follow these instructions can result in injury or equipment

damage.

Follow all start-up tests recommended in the equipment documentation.

Store all equipment documentation for future references.
Software testing must be done in both simulated and real
environments.

31007118 - 02/2018 9
 Verify that the completed system is free from all short circuits and
temporary grounds that are not installed according to local regulations
(according to the National Electrical Code in the U.S.A, for instance). If
high-potential voltage testing is necessary, follow recommendations in
equipment documentation to help prevent accidental equipment damage.

Before energizing equipment:

 Remove tools, meters, and debris from equipment.
 Close the equipment enclosure door.
 Remove all temporary grounds from incoming power lines.
 Perform all start-up tests recommended by the manufacturer.

 Operation and adjustments

The following precautions are from the NEMA Standards Publication
ICS 7.1-1995 (English version prevails):
 Regardless of the care exercised in the design and manufacture of
equipment or in the selection and ratings of components, there are
hazards that can be encountered if such equipment is improperly
operated.
 It is sometimes possible to misadjust the equipment and thus produce
unsatisfactory or unsafe operation. Always use the manufacturer’s
instructions as a guide for functional adjustments. Personnel who have
access to these adjustments should be familiar with the equipment
manufacturer’s instructions and the machinery used with the electrical
equipment.
 Only those operational adjustments actually required by the operator
should be accessible to the operator. Access to other controls should
be restricted to help prevent unauthorized changes in operating
characteristics.

 General safety instructions

Electricity is used to operate this equipment. Comply with every detail of
the safety requirements specified in the operating instructions regarding
the voltages to apply.
“Supply voltage” on page 11
 Only qualified personnel should work on this device or in its vicinity.
These personnel must be thoroughly familiar with all the hazard
messages and maintenance procedures in accordance with this
operating manual.
 The proper and safe operation of this device depends on proper
handling during transport, proper storage and assembly, and
conscientious operation and maintenance procedures.
 Never start operation with damaged components.
 Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.

10 31007118 - 02/2018
 Staff qualification requirements
Only appropriately qualified staff should work on or near this equipment.
Such staff must be thoroughly acquainted with all the hazard messages
and maintenance measures contained in these operating instructions.
The proper and safe operation of this equipment assumes proper
transport, appropriate storage and assembly, and careful operation and
maintenance.
Qualified staff are persons familiar with setting up, assembling,
installation, starting up, and operating this product, and who have
appropriate qualifications to cover their activities, such as:
 knowledge of how to switch circuits and equipment/systems on and
off, ground them, and identify them in accordance with current safety
standards
 training or instruction in accordance with current safety standards of
using and maintaining appropriate safety equipment
 first aid training

 Usage
The device may only be employed for the purposes described in the
catalog, technical description, and manuals.

 Supply voltage
For safety reasons the devices have been designed to operate at low
voltages. Thus, they may only be connected to the supply voltage
connections and to the signal contact with SELV circuits with the voltage
restrictions in accordance with IEC/EN 60950-1.
 Relevant for North America:
The device may only be connected to a Class 2 supply voltage that
fulfills the requirements of the National Electrical Code, Table 11(b). If
the voltage is being supplied redundantly (two different voltage
sources), the combined supply voltages must fulfill the requirements of
the National Electrical Code, Table 11(b).
 Relevant for North America: For use in class 2 circuits.
Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.
 Relevant for North America
for devices certified for hazardous locations:
Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods [Article 501-4(b) of the National
Electrical Code, NFPA 70] and in accordance with the authority having
jurisdiction.
 The device does not contain any service components. If the device is
not functioning correctly, or if it is damaged, switch off the voltage
supply and return the device to the plant for inspection.
 Apply supply voltage to the device if terminal blocks are wired and
installed correctly as described in chapter “Connecting the terminal
blocks for supply voltage and signal contact” on page 26.

31007118 - 02/2018 11
 Shielding ground
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
 Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.

 Housing

DANGER
HAZARD OF ELECTRIC SHOCK
Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of
the product.
Failure to follow these instructions will result in death, serious injury,
or equipment damage.

CAUTION
EQUIPMENT OVERHEATING
When installing the device, make sure any ventilation slots remain free.
Maintain a clearance of at least 3.94 in (10 cm).
Failure to follow these instructions can result in injury or equipment
damage.

CAUTION
OVERHEATING OF THE DEVICE

When installing the device, ensure that the ventilation slots are not covered.
Make sure there is at least 10 cm (3.94 in) of space.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

Only technicians authorized by the manufacturer are permitted to open

the casing.

12 31007118 - 02/2018
 The housing is grounded via the separate ground screw on the bottom left
of the front panel.
 Keep the ventilation slits free to ensure good air circulation.
 Verify that the electrical installation meets locally or nationally
applicable safety regulations.
 Make sure there is at least 3.94 inches (10 cm) of space in front of the
ventilation slits of the housing.

 The device must be installed in the vertical position.

 If installed in a living area or office environment, the device must be
operated only in switch cabinets with fire protection characteristics
according to EN 60950-1.
 Mount the device per instructions on page 28.

 Environment
The device may only be operated at the specified surrounding air
temperature (temperature of the surrounding air at a distance of up to
5 cm (1.97 in) from the device) and relative air humidity specified in the
technical data.
 Install the device in a location where the climatic threshold values
specified in the technical data will be observed.
 Use the device only in an environment within the pollution degree
specified in the technical data.

 Instructions for Use in Hazardous Locations

SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D
HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS
ONLY.
Peripheral equipment must be suitable for the location it is used in.
Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.

WARNING
EXPLOSION HAZARD
Substitution of any components may impair suitability for CLASS I,
DIVISION 2.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

31007118 - 02/2018 13
 WARNING
EXPLOSION HAZARD
Do not disconnect equipment unless power has been switched off or the
area is known to be non-hazardous.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

WARNING
EXPLOSION HAZARD
Do not use USB connector, or connect or disconnect devices from it unless
the area is known to be non-hazardous.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

14 31007118 - 02/2018
 
CONTROL DRAWING: Hazardous Locations Class I Division 2 Groups A, B ,C ,D
HAZARDOUS LOCATION NON HAZARDOUS LOCATION

3
 86%3RUWIRU$XWR&RQILJXUDWLRQ  3
  

$GDSWHU 3  3RZHUVXSSO\
 )RUPDLQWHQDQFHRQO\±6HH  
 5HGXQGDQW33
  9GF±9GF
 3 
 


 )DXOWFRQWDFWV
 (TXLSPHQWZLWKQRQLQFHQGLYHILHOGZLULQJSDUDPHWHUV
 99,P$/L—+&LQ) 1






 86%3RUWIRU$XWR&RQILJXUDWLRQ$GDSWHU
 )RU PDLQWHQDQFH RQO\ ± 6HH ,QVWDOODWLRQ
 Detail of TCSESM043F or TCSESM083F or ,QVWUXFWLRQV
 TCSESM103F or TCSESM163F
 or TCSESM243F Device




Notes:
7KHQRQLQFHQGLYHILHOGZLULQJFLUFXLWFRQFHSWDOORZVLQWHUFRQQHFWLRQRIQRQLQFHQGLYHILHOGZLULQJDSSDUDWXV
DQGDVVRFLDWHGQRQLQFHQGLYHILHOGZLULQJDSSDUDWXVXVLQJDQ\RIWKHZLULQJPHWKRGVSHUPLWWHGIRU
1 XQFODVVLILHGORFDWLRQVZKHQFHUWDLQSDUDPHWULFFRQGLWLRQVDUHPHW
Ca • Ci + CCable ; La • Li + LCable
1RQLQFHQGLYHILHOGZLULQJFLUFXLWVPXVWEHZLUHGLQDFFRUGDQFHZLWKWKH1DWLRQDO(OHFWULFDO&RGH1(&
1)3$DUWLFOH

Nonincendive Field Wiring Parameters:
(QWLW\3DUDPHWHUV Vmax Imax Ci Li
IRU&ODVV,'LYLVLRQ*URXSV$%&' ! >9@ >P$@ >Q)@ >—+@
 Fault contacts    

WARNING - EXPLOSION HAZARD – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY

FOR HAZARDOUS LOCATIONS OR EXPLOSIVE ATMOSPHERES.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN
SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

DO NOT OPEN WHEN ENERGIZED.




CONTROL DRAWING for TCSESM043F, TCSESM083F, TCSESM103F,
TCSESM163F and TCSESM243F Devices

6L]H$ 'RFXPHQW1R'15 5HY
'DWH 6KHHWRI 

31007118 - 02/2018 15
 CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/30/EU (EMC)
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to
electromagnetic compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Schneider Electric Systems USA, Inc.
38 Neponset Avenue
Foxboro, Massachusetts 02035-2037
United States of America
The device can be used in the industrial sector.
 Interference immunity: EN 61000-6-2
 Emitted interference: EN 55032

 LED or laser components

LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

16 31007118 - 02/2018
 FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.

 Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

31007118 - 02/2018 17
1 Description

1.1 General device description

A TCSESM switch is a compact, heavy-duty device suitable for industrial
applications which can be installed on a standard DIN Rail. The switches are
available in 4, 8, 10, 16 and 24 ports combinations. Two of these ports,
uplinks, usually used to implement the ring architectures, could be available
in Copper or Fiber (multimode, singlemode) and in 10/100 Mbps or Gigabit
speeds.
The 10-60VDC/18-30VAC operating voltage is supplied via a plug-in terminal
block with two connections to wire primary and redundant voltage if
necessary. An alarm relay allows reporting diagnostic information (P/S, Link
signal, Redundancy health) to Control systems. Integrated LEDs allow fast
on-site installation and troubleshooting.
Depending on the device variant, you can choose various media to connect
terminal devices and other infrastructure components:
 twisted pair cable
 multimode F/O
 singlemode F/O
The twisted pair ports support:
 Autocrossing
 Autonegotiation
 Autopolarity
There are convenient options for managing the device. Administer your
devices via:
 a Web browser
 Telnet
 a V.24 interface (locally on the device)
Product configuration data can be provided by:
 diagnosis displays
 displaying the operating parameters
 a label area for the IP address
The devices provide you with a large range of functions:
 Redundancy functions
 Rapid Spanning Tree Protocol (RSTP)
 HIPER-Ring
 Redundant coupling
 Redundant power supply
 Media Redundancy Protocol (MRP)

18 31007118 - 02/2018
 Security
 Protection from unauthorized access
 Blocking of unauthorized messages (MAC or IP based)
 Synchronized system time in the network
 Network load control
 Operation diagnosis
 Diagnostics (hardware self-testing)
 Reset
 Priority
 VLAN
 Topology Discovery
 Web based Interface
 Command Line Interface CLI
 SNMP
 Real Time Clock

1.2 Device versions

1.2.1 Device versions

Part Number Part Number Description

4 Port Version TCSESM043F23F0 4 10/100 TX Managed
TCSESM043F1CU0 3 10/100 TX 1 100 FX-MM Managed
TCSESM043F2CU0 2 10/100 TX 2 100 FX-MM Managed
TCSESM043F1CS0 3 10/100 TX 1 100 FX-SM Managed
TCSESM043F2CS0 2 10/100 TX 2 100 FX-SM Managed
8 Port Version TCSESM083F23F0 8 10/100 TX Managed
TCSESM083F1CU0 7 10/100 TX 1 100 FX-MM Managed
TCSESM083F2CU0 6 10/100 TX 2 100 FX-MM Managed
TCSESM083F1CS0 7 10/100 TX 1 100 FX-SM Managed
TCSESM083F2CS0 6 10/100 TX 2 100 FX-SM Managed
16 Port Version TCSESM163F23F0 16 10/100 TX Managed
TCSESM163F2CU0 14 10/100 TX 2 100 FX-MM Managed
TCSESM163F2CS0 14 10/100 TX 2 100 FX-SM Managed
24 Port Version TCSESM243F2CU0 22 10/100 TX 2 100 FX-MM Managed
Gigabit - 10 Port TCSESM103F23G0 8 10/100 TX 2 10/100/1000 TX Managed
Version TCSESM103F2LG0 8 10/100 TX, 2 1000 SFP (fiber) Managed
Note: This product ships with open sockets
(SFP) on the fiber ports. In order to use these
ports, order 1 or 2 fiber modules in any
combination (see below).
Fiber Media Modules TCSEAAF1LFU00 fiber module SFP-SX/LC
for Gigabit TCSEAAF1LFS00 fiber module SFP-LX/LC
TCSEAAF1LFH00 fiber module SFP-LH/LC

31007118 - 02/2018 19
Part Number Part Number Description
Accessories TCSEAM0100 Adapter Memory Back-up Adapter
490NTRJ11 Cable Terminal 490NTRJ11 cable

1.2.2 Examples of switch versions

1
Fault
+24V(P1) 0V 0V +24V(P2)

2
P Fault
Stand by
RM
ON
RM
3
Stand by

USB
4

MAC-Address
5
10

IP-ADDRESS
V.24

LNK 6
1
ACT
+24V(P1)
Fault
0V 0V +24V(P2) +24V(P1)
Fault
0V 0V +24V(P2)
9 LNK
P Fault P Fault 2
cable positions if DHCP Option 82 is enabled.
Stand by RM Stand by RM
RM
Stand by ON RM
Stand by ON UNINTENDED OPERATION Do not change
USB USB ACT
V.24
Check user manual before servicing.
LNK
WARNING

10
IP-ADDRESS

IP-ADDRESS

V.24
3
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

1 1
WARNING
Check user manual before servicing.

LNK LNK

1 ACT
7
1
ACT ACT
LNK LNK LNK
2 2
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

MAC-Address

ACT ACT
4
Check user manual before servicing.
WARNING

LNK LNK
MAC-Address

3 3
ACT
LNK
ACT ACT
LNK

4 4 2
ACT ACT

ConneXium Switch ConneXium Switch

ConneXium Switch
8
TCSESM043F1CU0/CS0 TCSESM043F2CU0/CS0 TCSESM043F23F0

Figure 1: The figure shows the 4-port version of the TCSESM.

1 – plug-in terminal block, 6-pin
2 – LED display elements
3 – 2-pin DIP switch
4 – USB interface
5 – V.24 connection for external management
6 – MAC address field
7 – ports in compliance with 10/100BASE-T(X) (RJ45 connections)
8 – protective ground (PE)
9 – IP address field
10 – port 1 + port 2, free choice of connections:
Twisted-pair T(X), RJ45, 10/100 Mbit/s
Multimode FX, DSC, 100 Mbit/s
Singlemode FX, DSC, 100 Mbit/s

20 31007118 - 02/2018
 1
Fault
+24V(P1) 0V 0V +24V(P2)

2
P Fault
LNK ACTStand by
RM ON
RM 3
10 Stand by

USB
4

MAC-Address
1

IP-ADDRESS
V.24

9 6

Fault Fault
+24V(P1) 0V 0V +24V(P2) +24V(P1) 0V 0V +24V(P2)

LNK ACT
P Fault
LNK
P
ACT Stand by
Fault
3 4

cable positions if DHCP Option 82 is enabled.

Stand by RM RM

UNINTENDED OPERATION Do not change

RM RM
ON ON
Stand by Stand by

USB USB
MAC-Address

MAC-Address
1
10

Check user manual before servicing.

WARNING
IP-ADDRESS

IP-ADDRESS

2 5 6
V.24

1 2
V.24

7
3 4 3 4
cable positions if DHCP Option 82 is enabled.
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

UNINTENDED OPERATION Do not change

ACT 7 8
Check user manual before servicing.
Check user manual before servicing.
WARNING

WARNING

5 6 2 5 6
LNK

ConneXium Switch
7 8

ConneXium Switch
7 8
8 ConneXium Switch

TCSESM083F23F0 TCSESM083F1CU0/CS0 TCSESM083F2CU0/CS0/CX0

Figure 2: The figure shows the 8-port versions of the TCSESM.

1 to 9 – see figure 1
10 – port 1 + port 2:
Twisted Pair T(X), RJ45, 10/100 Mbit/s
Multimode FX, DSC, 100 Mbit/s
Singlemode FX, DSC, 100 Mbit/s

31007118 - 02/2018 21
 1
Fault
+24V(P1) 0V 0V +24V(P2)

2
P Fault
LNK ACT Stand by
RM
ON
RM 3
10 Stand by

USB
4

MAC-Address
1

IP-ADDRESS
V.24

9 6
3 4

Fault
+24V(P1) 0V 0V +24V(P2)

LNK ACT

cable positions if DHCP Option 82 is enabled.

5 6 11 12
UNINTENDED OPERATION Do not change
P Fault
Stand by RM
RM
Stand by ON

USB

Check user manual before servicing.

MAC-Address

10
WARNING

2 7 8 13 14
IP-ADDRESS

1 2
V.24

9 10
7
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

3 4 11 12

9 10 15 16
Check user manual before servicing.
WARNING

5 6 13 14

7 8

ConneXium Switch
15 16
8 ConneXium Switch

7 7
TCSESM163F23F0 TCSESM163F2CU0/CS0

Figure 3: The figure shows the 16-port versions of the TCSESM.

1 to 9 – see figure 1
10 – port 1 + port 2:
Twisted Pair T(X), RJ45, 10/100 Mbit/s
Multimode FX, DSC, 100 Mbit/s
Singlemode FX, DSC, 100 Mbit/s

22 31007118 - 02/2018
 1
Fault
+24V(P1) 0V 0V +24V(P2)

3 4 2
P Fault
LNK ACT Stand by
RM
RM 3
10 5 6 Stand by ON

USB

MAC-Address
1
4
7 8

IP-ADDRESS
5
9 10 V.24

9 6
11 12

LNK ACT
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

13 14 19 20
Check user manual before servicing.

10
WARNING

2 15 16 21 22
7

17 18 23 24

8 ConneXium Switch

7 7
TCSESM243F2CU0

Figure 4: The figure shows the 24-port versions of the TCSESM.

1 to 9 – see figure 1
10 – port 1 + port 2, free choice of connections:
Multimode FX, DSC, 100 Mbit/s

1
Fault
+24V(P1) 0V 0V +24V(P2)

2
ACT
10 P Fault
1 Stand by
RM
RM 3
ON
LNK Stand by

USB
4
MAC-Address

5
9
IP-ADDRESS

V.24

6
3 4

ACT

2
10 5 6
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change

LNK

7
Check user manual before servicing.
WARNING

7 8

9 10

8 ConneXium Switch

TCSESM103F23G0

Figure 5: The figure shows the 10-port (gigabit) versions of the TCSESM.
1 to 9 – see figure 1
10 – port 1 + port 2:
Twisted Pair T(X), RJ45, 10/100/1000 Mbit/s
SX/LX, SFP-shaft, 1000 Mbit/s

31007118 - 02/2018 23
2 Assembly and start-up

2.1 Installing the device

Two or more devices configured with the same IP address can cause
unpredictable operation of your network.

WARNING
UNINTENDED EQUIPMENT OPERATION
Establish and maintain a process for assigning unique IP addresses to all
devices on the network.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

WARNING
UNINTENDED OPERATION
Do not change cable positions if DHCP Option 82 is enabled. Check the
Basic Configuration user manual before servicing (refer to DHCP
OPTION 82 topic).
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

2.1.1 Overview of installation

On delivery, the device is ready for operation.

The following steps should be performed to install and configure a device:

 Unpacking and checking
 Insert data in label area
 Installing the SFP transceivers (optional)
 Adjust DIP switch settings
 Connecting the terminal blocks for supply voltage and signal contact
 Installing the device on the DIN rail, grounding
 Installing the terminal block, start-up procedure
 Connecting the data lines

24 31007118 - 02/2018
2.1.2 Unpacking and checking
 Check whether the contents of the package are complete “Scope of
delivery” on page 40.
 Check the individual parts for transport damage.

2.1.3 Insert data in label area

The information field for the IP address on the front of the device helps you
to structure your network installation clearly.

Fault
+24V(P1) 0V 0V +24V(P2)

P Fault
LNK ACTStand by RM
RM ON
Stand by

USB
MAC-Address

2
IP-ADDRESS

V.24

1
LNK ACT
3 4
cable positions if DHCP Option 82 is enabled.
UNINTENDED OPERATION Do not change
Check user manual before servicing.
WARNING

2 5 6

7 8

ConneXium Switch

Figure 6: Label area for IP address of device

1 – IP address of device (label area)
2 – MAC address of device (label)

2.1.4 Installing the SFP transceivers (optional)

 Before attaching an SFP or XFP transceiver, first remove the protective
cap of the SFP/XFP transceiver.
 Push the SFP/XFP transceiver with the lock closed into the socket until it
latches audibly in place.

Figure 7: F/O SFP transceiver

31007118 - 02/2018 25
2.1.5 Adjust DIP switch settings
The 2-pin DIP switch on the front panel of the device gives you the following
options:

RM
ON
Stand by

Figure 8: 2-pin DIP switch

Switch Switch Ring Coupli Ring Coupli Ring Contro Coupl Software
RM Stand-by redun ng manager ng port l port ing configuratio
Position Position dancy switch manag port n
er
OFF OFF on on off off 1+2
ON OFF on on on off 1+2
OFF ON on on off on 1+2 3 4
ON ON SW
configuration
has priority
over DIP
switch
configuration

Delivery state: both DIP switches “ON”.

 Before starting operation of the device, check whether the default settings
of the DIP switch correspond to your requirements.

2.1.6 Connecting the terminal blocks for supply voltage

and signal contact

 Supply voltage

DANGER
HAZARD OF ELECTRIC SHOCK OR BURN
When the module is operated with direct plug-in power units, use only:
– SELV supply units that comply with IEC 60950/EN 60950 and
– (in USA and Canada) Class 2 power units that comply with applicable
national or regional electrical codes
Connect the ground wire to the PE terminal (where applicable) before you
establish any further connections. When you remove connections,
disconnect the ground wire last.
Failure to follow these instructions will result in death, serious injury,
or equipment damage.

26 31007118 - 02/2018
 Redundant power supplies can be used. Both inputs are uncoupled.
There is no distributed load. With redundant supply, the power supply unit
supplies the device only with the higher output voltage. The supply
voltage is electrically isolated from the housing.
You can choose between DC or AC voltage when connecting the supply
voltage. You use the +24V and 0V pins to connect the AC voltage (see
figure 9).

FAULT FAULT

+24V(P1) 0V 0V +24V(P2) +24V(P1) 0V 0V +24V(P2)

+ - - + G G

1 1 2 2

Figure 9: Connecting the supply voltage at the 6-pin terminal block

1 – DC voltage, voltage range: 9.6 V DC to 60 V DC
2 – AC voltage, voltage range: 18 V AC to 30 V AC

 Signal contact
 The signal contact (“FAULT”, for pin assignment of terminal block, see
figure 9) monitors the functioning of the device, thus enabling remote
diagnostics. You can specify the type of function monitoring in the
Management.
 You can also use the switch Web page to switch the signal contact
manually and thus control external devices.
The potential-free signal contact (relay contact, closed circuit) reports
through a break in contact:
 The detected inoperability of at least one of the two voltage supplies
(voltage supply 1 or 2 is below the threshold value).
 Loss of connection to at least one port.
The link state can be masked for each port using the configuration. In
the state of delivery, link monitoring is inactive.
 Loss of the ring redundancy reserve.
 A detected error during the self-test.
The following condition is also reported in RM mode:
 Ring redundancy reserve is available. On delivery, there is no ring
redundancy monitoring.
 Pull the terminal block off the device and connect the power supply
and signal lines.

31007118 - 02/2018 27
2.1.7 Installing the device on the DIN rail, grounding

 Mounting on the DIN rail

Mount the device on a 35 mm DIN rail in accordance with DIN EN 60715.
Attach the upper snap-in guide of the device into the DIN rail and press
the device down against the DIN rail until it snaps into place.

Note: The shield ground wire of the twisted pair lines is connected to the
front panel as a conductor.

Figure 10: Mounting on the DIN rail

 Grounding
The device is grounded by the separate ground screw on the front panel.

28 31007118 - 02/2018
2.1.8 Dimension drawings

Figure 11: 4 Port Versions

Figure 12: 8 and 10 Port Versions

31007118 - 02/2018 29
Figure 13: 16 and 24 Port Versions

2.1.9 Installing the terminal block, start-up procedure

 Mount the terminal block for the voltage supply and signal contact on the
front of the device by snapping the lock into place.
By connecting the supply voltage via the terminal block, you start the
operation of the device.

2.1.10 Connecting the data lines

You can connect terminal devices and other segments on the ports of the
device via twisted pair cables or F/O cables.
 Install the data lines according to your requirements.

 10/100 Mbit/s twisted pair connection

These connections are RJ45 sockets.
10/100 Mbit/s TP ports enable the connection of terminal devices or
independent network segments according to the IEEE 802.3 10BASE-T/
100BASE-TX standard.
These ports support:
 Autonegotiation
(data rate and duplex mode)
 Autopolarity
 Autocrossing (if autonegotiation is activated)

30 31007118 - 02/2018
  100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
 10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
Delivery state: autonegotiation activated
The socket housing is electrically connected to the front panel.

Figure Pin Operation

1
1+2 One line pair: receiver path
2 3+6 One line pair: sender path
3
4
4,5,7,8 —
5
6
7
8

Table 1: Pin assignment of a TP/TX interface in MDI-X mode, RJ45 socket

 10/100/1000 Mbit/s twisted pair connection

These connections are RJ45 sockets.
10/100/1000 Mbit/s TP ports enable the connection of terminal devices or
independent network segments according to the IEEE 802.3 10BASE-T/
100BASE-TX/1000BASE-T standard.
These ports support:
 Autonegotiation
(data rate and duplex mode)
 Autopolarity
 Autocrossing (if autonegotiation is activated)
 1000 Mbit/s full duplex
 100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
 10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
Delivery state: autonegotiation activated
The socket housing is electrically connected to the front panel.
The pin assignment corresponds to MDI-X.

Pin Function
1
1 BI_DB +
2 2 BI_DB −
3
4
3 BI_DA +
5 4 BI_DD +
6
7
5 BI_DD −
8 6 BI_DA −
7 BI_DC +
8 BI_DC −
Table 2: Pin assignment of a 1000 MBit/s TP interface in MDI-X mode, RJ45
socket

31007118 - 02/2018 31
 100 Mbit/s F/O connection
These connections are DSC connectors.
100 MBit/s F/O ports enable the connection of terminal devices or
independent network segments in compliance with the IEEE 802.3
100BASE-FX standard.
These ports support:
 Full or half duplex mode
Default setting: Full duplex

Note: Make sure that the SM ports are only connected with SM ports, and
MM ports only with MM ports.

 1000 Mbit/s F/O connection

These ports are SFP slots.
1000 Mbit/s F/O ports enable the connection of terminal devices or
independent network segments according to the IEEE 802.3 1000BASE-
SX/1000BASE-LX standard.
These ports support:
 Autonegotiation
 Full duplex mode
Delivery state: autonegotiation activated

Note: Make sure that the LH ports are only connected with LH ports, SX
ports are only connected with SX ports, and LX ports only with LX ports.

2.2 Display elements

After the operating voltage is set up, the software starts and initializes itself.
Afterwards, the device performs a self-test. During this process, various
LEDs light up. The process takes around 60 seconds.

 Device state
These LEDs provide information about conditions which affect the
operation of the whole device.

P FAULT
Stand by RM

Figure 14: Device status LEDs

P - Power (green/yellow LED)

Glowing green Both supply voltages are on
Glowing yellow There is only one supply voltage (P1 or P2) on

32 31007118 - 02/2018
P - Power (green/yellow LED)
Not glowing Supply voltages P1 and P2 are too low

FAULT - detected error, signal contact (red LED)a

Glowing red The signal contact is open, i.e. it is reporting a detected error.
Not glowing The signal contact is closed, i.e. it is not reporting a detected
error.
a. If the manual adjustment is active on the "FAULT" signal contact, then the detected error
display is independent of the setting of the signal contact.

RM - Ring Manager (green/yellow LED)

Glowing green RM function active, redundant port disabled
Glowing yellow RM function active, redundant port enabled
Not glowing RM function not active
Flashing green Incorrect configuration of the HIPER-Ring (e.g. the ring is not
connected to the ring port).

Stand-by
Glowing green Stand-by mode enabled
Not glowing Stand-by mode not enabled

 Port status
The green and yellow LEDs at the individual port display port-related
information. During the boot phase, these LEDs are used to display the
status of the boot procedure.

ACT LNK

1 1 LNK ACT
LNK ACT

1 1 2 3

Figure 15: Port status LEDs

1 – Port status LEDs for isolated or single-row RJ45 sockets: one green
and one yellow LED per port.
2 – Port status LEDs for double-row RJ45 sockets: one LED per port,
glowing/flashing either green or yellow.
3 – Port status LEDs for DSC, SFP

LED Display Color Activity Meaning

LNK Link status Green Lights up The device detects a valid
connection.
None The device detects an invalid or
missing connection.
flashes (1 time/s) The port is switched to stand-by.
flashes (3 times/s) The port is disabled.
ACT data Yellow None No data reception at this port
Flashing Data reception at this port

31007118 - 02/2018 33
2.3 Basic set-up
When you install the device for the first time enter the IP parameters.
The device provides the following options for configuring IP addresses:
 Configuration via V.24 connection
 Configuration via the switch configurator software
 Configuration via BOOTP
 Configuration via DHCP
 Configuration via the Memory Back-up Adapter (TCSEAM 0100)

Further information on the basic settings of the device can be found in the
“Basic Configuration” user manual on the CD/DVD.

 Default settings
 IP address: The device looks for the IP address using DHCP
 Password for management:
Login: user; password: public (read only)
Login: admin; password: private (read and write)
 V.24 data rate: 9600 Baud
 Ring redundancy: disabled
 Ethernet ports: link status is not evaluated (signal contact)
 Optical 100 Mbit/s ports: 100 Mbit/s, full duplex
All other ports: autonegotiation
 Ring Manager disabled (DIP switch RM and stand-by: ON)
 Stand-by coupling disabled (DIP switch RM and stand-by: ON)
Port 4 = control port, port 3 = coupling port for red. Ring coupling
 Rapid Spanning Tree enabled

 USB interface
The USB socket has an interface for the local connection of a Memory
Back-up Adapter (EAM). The EAM is used for saving/loading the
configuration data and diagnostic information, and for loading the
software.

Figure Pin Operation

1 2 34
1 VCC (VBus)
2 − Data
3 + Data
4 Ground (GND)
Table 3: Pin assignment of the USB interface

34 31007118 - 02/2018
 V.24 interface (external management)
The V.24 interface is an RJ11 socket.
The V.24 interface is a serial interface which allows you to connect the
following devices locally:
 An external management station (VT100 terminal or PC with
appropriate terminal emulation). This enables you to set up a
connection to the Command Line Interface (CLI) and to the system
monitor.
 A Memory Back-up Adapter (TCSEAM0100)

VT100 terminal settings

Speed 9600 Baud
Data 8 bit
Stopbit 1 bit
Handshake off
Parity none

The socket housing is electrically connected to the front panel of the

device. The V.24 interface is not electrically isolated from the supply
voltage.

RJ11 DB9 RJ11 DB9

5 CTS 1
6 n.c. 2 2
8 TX 3 3
1 GND 4
1 RX 5 5
RTS 6

Figure 16: Pin assignment of the V.24 interface and the DB9 connector

Note: You can order the terminal cable separately (ref #: 490NTRJ11).

You will find a description of the V.24 interface in the “Basic Configuration
User Manual” on the CD-ROM.

31007118 - 02/2018 35
2.4 Disassembly
 Removing the device from the DIN rail
 To take the device off the DIN rail, insert a screwdriver horizontally
under the housing into the locking slide, pull it (without tipping the
screwdriver) downwards and lift the device upwards.

 Removing the SFP transceivers

 Pull the module out of the socket by means of the opened lock.
 Close the module with the protective cap.

36 31007118 - 02/2018
3 Technical data
 General technical data

Dimensions TCSESM04 47 mm x 131 mm x 111 mm

WxHxD 1.85 in x 5.16 in x 4.3 in
TCSESM08 and TCSESM10 74 mm x 131 mm x 111 mm
2.91 in x 5.16 in x 4.37 in
TCSESM16 and TCSESM24 111 mm x 131 mm x 111 mm
4.37 in x 5.16 in x 4.37 in
Weight TCSESM04 400 g
TCSESM08 410 g
TCSESM10 410 g
TCSESM16 600 g
TCSESM24 610 g
Power supply Operating voltage 9.6 to 60 V DC or 18 to 30 V AC
Safety extra-low voltage (SELV),
redundant inputs disconnected.
Relevant for North America: NEC
Class 2 power source max. 5A.
Overload current Non-replaceable fuse
protection at input
Insulation voltage between operating voltage connections 800 V DC
and housing Protective elements limit the
insulation voltage to 90 V DC (1 mA)
“FAULT” Switching current max. 1 A, SELV
signal contact Switching voltage max. 60 V DC or max. 30 V AC,
SELV
Environment Storage temperature -40 °C (-40 °F ) to +80 °C (+176 °F )
(ambient air)
Humidity 10 % ... 95 %
(non-condensing)
Air pressure Up to 2000 m (795 hPa), higher
altitudes on request
Operating 0 °C (+32 °F) to +60 °C (+140 °F)
temperature
Pollution degree 2
Protection classes Laser protection Class 1 in compliance with IEC
60825-1
Degree of protection IP20

 EMC and immunity

EMC compliance – IEC/EN 61000-6-2:2005 EMI TYPE tests, test acc. to:
IEC/EN 61000-4-2 Electrostatic discharge
Contact discharge 8 kV
IEC/EN 61000-4-3 Electromagnetic field
80 MHz ... 3000 MHz 20 V/m
IEC/EN 61000-4-4 Fast transients (burst)
Power line 4 kV
Data line 4 kV

31007118 - 02/2018 37
EMC compliance – IEC/EN 61000-6-2:2005 EMI TYPE tests, test acc. to:
IEC/EN 61000-4-5 Voltage surges
Power line, line / line 1 kV
Power Line, line / ground 2 kV
Data line 2 kV
IEC/EN 61000-4-6 Conducted disturbances
10 kHz ... 150 kHz 3V
150 kHz ... 80 MHz 10 V
EN 61000-4-9 Pulse magnetic fields 300 A/m

EMC interference emission

EN 55032 Class A Yes
FCC 47 CFR Part Class A Yes
15
German Lloyd Classification + Construction Guidelines VI-7-3 Part 1 Ed.2001 Yes

Stability
Vibration IEC 60068-2-6 Test FC test level according to IEC 61131-2 Yes
Shock IEC 60068-2-27 Test Ea test level according to IEC 61131-2 Yes

38 31007118 - 02/2018
 Network range

10/100/1000 Mbit/s twisted pair port

Length of a twisted pair segment max. 328 ft (100 m) (for Cat5e cable)
Table 4: Network range: 10/100/1000 Mbit/s twisted pair port

Description Wave Fiber System Example Fiber data

length attenuatio for F/O line
n length
Multimode FX, 1300 nm 50/125 µm 0-8 dB 0-5 km 1.0 dB/km, 800 MHz×km
DSC, 10/100
Mbit/s
Multimode FX, 1300 nm 62.5/125 µm 0-11 dB 0-4 km 1.0 dB/km, 500 MHz×km
DSC, 10/100
Mbit/s
Singlemode 1300 nm 9/125 µm 0-16 dB 0-30 km 0.4 dB/km; 3.5 ps/(nm×km)
FX, DSC, 10/
100 Mbit/s
Table 5: F/O port 100BASE-FX

Description Wave Fiber System Example Fiber data

SFP-... length attenuati for F/O
on line length
-SX/LC... MM 850 nm 50/125 µm 0-7.5 dB 0-550 m 3.0 dB/km 400 MHz×km
-MX/LC MM 1310 nm 50/125 µm 0-8 dB 2 kma 1.0 dB/km 500 MHz×km
-MX/LC MM 1310 nm 62.5/125 µm 0-8 dB 1 km 1.0 dB/km 500 MHz×km
-LX/LC... MM 1310 nmb 50/125 µm 0-10.5 dB 0-550 m 1.0 dB/km 800 MHz×km
-LH/LC... LH 1550 nm 9/125 µm 5-22 dB 23-80 km 0.25 dB/km 19 ps/(nm×km)
-LX+/LC... SM 1310 nm 9/125 µm 5-20 dB 14-42 km 0.4 dB/km 3.5 ps/(nm×km)
Table 6: Fiber port 1000BASE-FX (SFP fiber optic Gigabit Ethernet Transceiver)
a. Distances of up to 3 km reachable, 1000 MHz*km (1300 nm)
b. With F/O adapter compliant with IEEE 802.3-2002 clause 38 (single-mode fiber offset-
launch mode conditioning patch cord)

MM = Multimode, SM = Singlemode, LH = Singlemode Longhaul

 Power consumption/power output

Device name Device model Maximum Power output

power
consumption
TCSESM04 2xTX port 5.3 W 18.1 Btu (IT)/h
TCSESM04 1xFX port, 1xTX port 6.5 W 22.2 Btu (IT)/h
TCSESM04 2xFX port 7.7 W 26.3 Btu (IT)/h
TCSESM08 2xTX port 5.3 W 18.1 Btu (IT)/h
Table 7: Power input/output for the TCSESM devices

31007118 - 02/2018 39
Device name Device model Maximum Power output
power
consumption
TCSESM08 1xFX port, 1xTX port 6.5 W 22.2 Btu (IT)/h
TCSESM08 2xFX port 7.7 W 26.3 Btu (IT)/h
TCSESM10 (with gigabit ports) 2xTX port 8.9 W 30.4 Btu (IT)/h
TCSESM10 (with gigabit ports) 2xFX port 8.3 W 28.4 Btu (IT)/h
TCSESM16 2xTX port 9.4 W 32.1 Btu (IT)/h
TCSESM16 2xFX port 11.8 W 40.3 Btu (IT)/h
TCSESM24 2xFX port 14.5 W 52.9 Btu (IT)/h
Table 7: Power input/output for the TCSESM devices

 Recommended fuses

Device name Fuse

TCSESM04xx 1.5 A, slow/delay fuse
TCSESM08xx 1.5 A, slow/delay fuse
TCSESM10xx 2.0 A, slow/delay fuse
TCSESM16xx 2.0 A, slow/delay fuse
TCSESM24xx 3.0 A, slow/delay fuse

 Scope of delivery

Device Scope of delivery

TCSESMxx Device
Terminal block for supply voltage and signal contact
CD-ROM (includes user technical documentation)

 Order numbers/product description

Part Number Part Number Description

4 Port Version TCSESM043F23F0 4 10/100 TX Managed
TCSESM043F1CU0 3 10/100 TX 1 100 FX-MM Managed
TCSESM043F2CU0 2 10/100 TX 2 100 FX-MM Managed
TCSESM043F1CS0 3 10/100 TX 1 100 FX-SM Managed
TCSESM043F2CS0 2 10/100 TX 2 100 FX-SM Managed
8 Port Version TCSESM083F23F0 8 10/100 TX Managed
TCSESM083F1CU0 7 10/100 TX 1 100 FX-MM Managed
TCSESM083F2CU0 6 10/100 TX 2 100 FX-MM Managed
TCSESM083F1CS0 7 10/100 TX 1 100 FX-SM Managed
TCSESM083F2CS0 6 10/100 TX 2 100 FX-SM Managed
16 Port Version TCSESM163F23F0 16 10/100 TX Managed
TCSESM163F2CU0 14 10/100 TX 2 100 FX-MM Managed
TCSESM163F2CS0 14 10/100 TX 2 100 FX-SM Managed
24 Port Version TCSESM243F2CU0 22 10/100 TX 2 100 FX-MM Managed

40 31007118 - 02/2018
Part Number Part Number Description
Gigabit - 10 Port TCSESM103F23G0 8 10/100 TX 2 10/100/1000 TX Managed
Version TCSESM103F2LG0 8 10/100 TX, 2 1000 SFP (fiber) Managed
Note: This product ships with open sockets
(SFP) on the fiber ports. In order to use these
ports, order 1 or 2 fiber modules in any
combination (see below).
Fiber Media Modules TCSEAAF1LFU00 fiber module SFP-SX/LC
for Gigabit TCSEAAF1LFS00 fiber module SFP-LX/LC
TCSEAAF1LFH00 fiber module SFP-LH/LC

Accessories TCSEAM0100 Adapter Memory Back-up Adapter

490NTRJ11 Cable Terminal 490NTRJ11 cable

 Underlying norms and standards

Standard
EN 10155 Declaration (railroad)
EN 50121-4 Railway applications - EMC - emitted interference and interference
immunity for signal and telecommunication systems
EN 55032 Electromagnetic compatibility of multimedia equipment – Emission
Requirements
EN 61000-6-2 Generic norm – immunity in industrial environments
EN 61131-2 Programmable logic controllers
FCC 47 CFR Part 15 Code of Federal Regulations
EN 60950-1 Safety for the installation of IT equipment
IEC/EN 61850-3 Communications networks and systems in substations
IEEE 1613 Standard Environment and Testing Requirements for
Communication Networking Devices in Electric Power Substations

 Certifications

Standard
UL 508 / CSA C22.2 Safety for Industrial Control Equipment
No.142

ISA 12.12.01 / CSA C22.2 Electrical Equipment for Use in Class I and Class II, Div. 2 and
No.213 Class III Hazardous (Classified) Locations

Germanischer Lloyd Rules for Classification and Construction VI-7-2 – GL

The TCSESM switches have CE certifications.

31007118 - 02/2018 41