WARNING

This manual contains information on limitations regarding product use and function and information on the
limitations as to liability of the manufacturer. The entire manual should be carefully read.

This panel will not operate if installed outside of North America. See section 1.1 for details.

Installation
Manual

Software Version 2.3 / DLS-1 v6.7 and up

See Back Cover for New Features in Version 2.3

WARNING Please Read Carefully Limited Warranty
N o te t o I n s t al le r s Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the
This warning contains vital information. As the only individual in contact with system users, it is your date of purchase, the product shall be free of defects in materials and workmanship under normal use. Dur-
responsibility to bring each item in this warning to the attention of the users of this system. ing the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective
S ys te m Fa i lu r e s product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/
This system has been carefully designed to be as effective as possible. There are circumstances, however,
involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm sys- or repaired parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is
tem of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. longer. The original owner must promptly notify Digital Security Controls Ltd. in writing that there is defect
Some but not all of these reasons may be: in material or workmanship, such written notice to be received in all events prior to expiration of the war-
■ Inadequate Installation ranty period.
A security system must be installed properly in order to provide adequate protection. Every installation
should be evaluated by a security professional to ensure that all access points and areas are covered. Locks I n te r na t io na l War ra n ty
and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings The warranty for international customers is the same as for any customer within Canada and the United
and other building materials must be of sufficient strength and construction to provide the level of protection States, with the exception that Digital Security Controls Ltd. shall not be responsible for any customs fees,
expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire taxes, or VAT that may be due.
and/or police department is highly recommended if this service is available.
■ Criminal Knowledge Wa rr an t y P ro c e d u r e
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All
This system contains security features which were known to be effective at the time of manufacture. It is pos-
sible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. authorized distributors and dealers have a warranty program. Anyone returning goods to Digital Security
It is important that a security system be reviewed periodically to ensure that its features remain effective and Controls Ltd. must first obtain an authorization number. Digital Security Controls Ltd. will not accept any
that it be updated or replaced if it is found that it does not provide the protection expected. shipment whatsoever for which prior authorization has not been obtained.
■ Access by Intruders C o n di ti o n s t o Vo id Wa rr a n ty
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:
moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent
the proper operation of the system. • damage incurred in shipping or handling;
■ Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate • damage caused by disaster such as fire, flood, wind, earthquake or lightning;
power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. • damage due to causes beyond the control of Digital Security Controls Ltd. such as excessive voltage,
Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a mechanical shock or water damage;
device operates only by AC power, any interruption, however brief, will render that device inoperative while
it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations • damage caused by unauthorized attachment, alterations, modifications or foreign objects;
which may damage electronic equipment such as a security system. After a power interruption has occurred,
immediately conduct a complete system test to ensure that the system operates as intended. • damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.);
■ Failure of Replaceable Batteries • defects caused by failure to provide a suitable installation environment for the products;
This system’s wireless transmitters have been designed to provide several years of battery life under normal
conditions. The expected battery life is a function of the device environment, usage and type. Ambient con- • damage caused by use of the products for purposes other than those for which it was designed;
ditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the
expected battery life. While each transmitting device has a low battery monitor which identifies when the • damage from improper maintenance;
batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance • damage arising out of any other abuse, mishandling or improper application of the products.
will keep the system in good operating condition.
■ Compromise of Radio Frequency (Wireless) Devices Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reason-
Signals may not reach the receiver under all circumstances which could include metal objects placed on or able number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach
near the radio path or deliberate jamming or other inadvertent radio signal interference. of warranty. Under no circumstances shall Digital Security Controls Ltd. be liable for any special, incidental,
■ System Users or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or
A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any
physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services,
important that all system users be trained in the correct operation of the alarm system and that they know down time, purchaser’s time, the claims of third parties, including customers, and injury to property.
how to respond when the system indicates an alarm.
■ Smoke Detectors D i s c la i m e r o f Wa rr an t ie s
Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of rea- This warranty contains the entire warranty and shall be in lieu of any and all other warranties,
sons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke whether expressed or implied (including all implied warranties of merchantability or fitness for a par-
may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the ticular purpose) And of all other obligations or liabilities on the part of Digital Security Controls Ltd.
other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the resi- Digital Security Controls Ltd. neither assumes nor authorizes any other person purporting to act on
dence or building.
its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability
Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot
sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by concerning this product.
carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of This disclaimer of warranties and limited warranty are governed by the laws of the province of
flammable materials, overloaded electrical circuits, children playing with matches or arson. Ontario, Canada.
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warn-
ing to allow all occupants to escape in time to avoid injury or death. WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a
■ Motion Detectors regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electri-
Motion detectors can only detect motion within the designated areas as shown in their respective installation cal disruption, it is possible for this product to fail to perform as expected.
instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not
provide volumetric area protection. They have multiple beams of detection and motion can only be detected I n st a l le r ’ s L o c k o ut
in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceil- Any products returned to DSC which have the Installer’s Lockout option enabled and exhibit no other prob-
ings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional lems will be subject to a service charge.
or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or
any other part of the detection system will impair its proper operation. O u t o f Wa rr a n ty R e p ai r s
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness Digital Security Controls Ltd. will at its option repair or replace out-of-warranty products which are returned
can be reduced when the ambient temperature rises near or above body temperature or if there are intentional to its factory according to the following conditions. Anyone returning goods to Digital Security Controls
or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, Ltd. must first obtain an authorization number. Digital Security Controls Ltd. will not accept any shipment
radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on. whatsoever for which prior authorization has not been obtained.
■ Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if Products which Digital Security Controls Ltd. determines to be repairable will be repaired and returned. A
there is an intervening wall or door. If warning devices are located on a different level of the residence or set fee which Digital Security Controls Ltd. has predetermined and which may be revised from time to time,
premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be will be charged for each unit repaired.
interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appli-
ances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired Products which Digital Security Controls Ltd. determines not to be repairable will be replaced by the nearest
person. equivalent product available at that time. The current market price of the replacement product will be
■ Telephone Lines charged for each replacement unit.
If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time.
Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may
be difficult to detect.
■ Insufficient Time
There may be circumstances when the system will operate as intended, yet the occupants will not be pro-
tected from the emergency due to their inability to respond to the warnings in a timely manner. If the system
is monitored, the response may not occur in time to protect the occupants or their belongings.
■ Component Failure
Although every effort has been made to make this system as reliable as possible, the system may fail to func-
tion as intended due to the failure of a component.
■ Inadequate Testing
Most problems that would prevent an alarm system from operating as intended can be found by regular test-
ing and maintenance. The complete system should be tested weekly and immediately after a break-in, an
attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or
outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating
devices and any other operational devices that are part of the system.
■ Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm sys-
tem also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or
minimize the harmful effects of an emergency situation.
 Ta b le o f Co nte nts
Section 1: System Introduction 1 5.4 Assigning Keypad Zones ................................................. 17
1.1 Specifications ........................................................................1 5.5 Communicator – Dialing .................................................. 17
1.2 Additional Devices ..............................................................2 5.6 Communicator – Account Numbers .............................. 17
1.3 Out of the Box .......................................................................2 5.7 Communicator – Telephone Numbers ........................... 17
Section 2: Getting Started 3 5.8 Communicator – Reporting Codes ................................. 18
2.1 Installation Steps ..................................................................3 5.9 Communicator – Reporting Formats .............................. 19
2.2 Terminal Descriptions .........................................................3 5.10 Downloading ..................................................................... 20
2.3 Keybus Operation and Wiring ...........................................4 5.11 PGM Output Options ....................................................... 20
2.4 Current Ratings – Modules and Accessories ...................4 5.12 Telephone Line Monitor (TLM) ...................................... 22
2.5 Keypad Assignment ............................................................4 5.13 Bell ....................................................................................... 22
2.6 Supervision ...........................................................................5 5.14 Test Transmission .............................................................. 22
2.7 Removing Modules ..............................................................5 5.15 Transmission Delay .......................................................... 23
2.8 Zone Wiring ..........................................................................5 5.16 Fire, Auxiliary and Panic Keys ........................................ 23
2.9 Fire Zone Wiring ..................................................................6 5.17 Arming/Disarming Options ........................................... 23
2.10 LINKS Zone Wiring* ...........................................................6 5.18 Entry/Exit Delay Options ................................................ 24
2.11 Keypad Zones .......................................................................6 5.19 Swinger Shutdown ............................................................ 24
Section 3: Keypad Commands 8 5.20 Event Buffer ....................................................................... 24
3.1 Arming and Disarming .......................................................8 5.21 Keypad Lockout Options ................................................. 24
3.2 Auto Bypass – Stay Arming ...............................................8 5.22 Keypad Blanking ............................................................... 24
3.3 Automatic Arming ...............................................................8 5.23 Keypad Backlighting ........................................................ 25
3.4 [*] Commands .......................................................................8 5.24 Loop Response ................................................................... 25
3.5 Function Keys .....................................................................11 5.25 Keypad Tampers ............................................................... 25
3.6 Features Available for the LCD5500Z .............................12 5.26 LINKS1000 Cellular Communicator* ............................. 25
5.27 Additional System Modules ............................................ 26
Section 4: How to Program 13
4.1 Installer’s Programming ...................................................13 5.28 Resetting Factory Defaults ............................................... 26
4.2 Programming Decimal Data .............................................13 5.29 Installer’s Lockout ............................................................. 26
4.3 Programming HEX Data ...................................................13 5.30 Walk Test (Installer) .......................................................... 26
4.4 Programming Toggle Option Sections ............................14 Section 6: Programming Worksheets 27
4.5 Viewing Programming ......................................................14 Appendix A: Reporting Codes 42
Section 5: Program Descriptions 15 Appendix B: Programming LCD Keypads 44
5.1 Programming Security Codes ..........................................15
5.2 Zone Programming ............................................................15
5.3 Zone Attributes ..................................................................16

i
 P C 5 8 0 Wiri ng Di ag ram

ii
 S e c tion 1 : Sy s te m Intro d u cti o n
1.1 Specifications Digital Communicator Specifications*
• Supports major communication formats including SIA and
Downloading Software Support Contact ID
• PC580 v2.3 uses DLS-1 v6.7 and up.
• Digital Communicator compatible receivers and their formats:
Flexible Zone Configuration Silent Knight Model 9000: 3/1, 4/1, 4/2 non-extended, 3/1
• Four fully programmable zones extended, 20 bps, 1400 Hz handshake.
• System expandable to 8 zones using keypad zone inputs and Ademco Model 685: 3/1, 4/1, 4/2 non-extended, 3/1
to 32 zones using the PC5132 wireless expansion module extended, 20 bps, 1400 Hz handshake, Contact ID.
• 38 access codes: one master code, one maintenance Sescoa Model 3000: 3/1, 4/1, 4/2 non-extended, 3/1
code, two duress codes, two supervision codes and 32 extended, 20 bps, 1400 Hz handshake.
general access codes Radionics Model D6500: 3/1, 4/2 non-extended, 3/1
• 27 zone types; 8 programmable zone attributes extended, with or without parity, 1400 and 2300 Hz handshake.
• Normally closed, single EOL and double EOL zone wiring Sur-Gard Model MLR2-DG: 3/1, 4/1, 4/2, without parity, 20
• 32 wireless zones with the PC5132 Wireless Receiver bps, 1400 and 2300 Hz handshake, Contact ID, SIA.
• Event-initiated personal paging
Audible Alarm Output
• Three programmable telephone numbers
• 700mA Supervised Bell Output (current limited at 3 amps),
12VDC • Two account numbers
• Steady or Pulsed Output • Supports LINKS1000 cellular communication
• Supports LINKS2X50 long range radio transmitter
EEPROM Memory • Supports Skyroute transceiver
• Does not lose programming or system status on complete • DTMF and pulse dialing
AC and Battery failure • DPDT line seizure
Programmable Outputs • Anti-jam feature
• Two programmable outputs; 18 programmable options • Split reporting of selected transmissions to each telephone
• PGM1 = 50mA; PGM2 = 50mA number
Powerful 1.5 Amp Regulated Power Supply System Supervision Features
• 550 mA Auxiliary Supply, 12 VDC The PC580 continuously monitors a number of possible trou-
• Positive Temperature Coefficient (PTC) components ble conditions including:
replace fuses • AC power failure • AUX Power Supply Trouble
• Supervision for loss of AC power, low battery • Fault by zone • Loss of internal clock
• Internal clock locked to AC power frequency • Tamper by zone • Bell output trouble
Power Requirements • Fire trouble • Telephone line trouble
• Transformer = 16.5 VAC, 40VA • Failure to communicate • Low battery condition (panel)
• Battery = 12 volt 4 Ah minimum rechargeable sealed lead • Low battery by zone (wireless)
acid battery • Module fault (supervisory or tamper)
• For household fire and burglary installations, two 7Ah bat- False Alarm Prevention Features
teries in parallel must be used, providing 24 hours of • Audible Exit Delay • Quick Exit
standby power and 4 minutes of alarm output power. • Audible Exit Fault • Cross Zone Burglary Alarm
• For commercial burglary installations, a 4Ah (or larger) bat- • Communication Delay • Rotating Keypress Buffer
tery must be used, providing at least 4 hours of standby • Urgency on Entry Delay
power and 4 minutes of alarm output power.
Additional Features
WARNING: Do not install this panel outside of North America.
• Auto Arm at specified time
By design, this panel will not work if the AC line frequency
• Keypad-activated alarm output and communicator test
drops below 55.5Hz. • All modules connect to the system via a four wire Keybus
Remote Keypad Specifications up to 1000’/305m from main panel
• Keypads available: • An event buffer which records the past 128 events with
- PC1555RKZ eight zone LED keypad with zone input both the time and date at which they occurred; buffer can
- PC5508Z eight zone LED keypad with zone input be printed using PC5400 serial interface module, or
- PC5516Z sixteen zone LED keypad with zone input viewed with the LCD5500Z keypad and DLS-1 software
- PC5532Z thirty-two zone LED keypad with zone input • Supports the addition of the PC5132 wireless receiver for
- LCD5500Z Alphanumeric keypad with zone input integration of wireless devices
• All keypads have five programmable function keys • Uploading and downloading capability
• Connect up to eight keypads • Local downloading capability through the use of the
• 4-wire (Quad) connection to Keybus PC-LINK adaptor
• Built in piezoelectric buzzer • Added Keybus fault protection: clock and data outputs
have been programmed to withstand shorts to +12v to pre-
vent control panel damage

*LINKS1000, LINKS2X50, and Skyroute have not been investigated by UL. 1

1.2 Additional Devices Cabinets
In addition to the information below, see the back cover for a Several different cabinets are available for the PC580 mod-
DSC module compatibility table. ules. They are as follows:
PC5132 Wireless Receiver PC5003C Cabinet
The PC5132 Wireless Receiver can be used to connect up to Main control cabinet for the PC580 main panel. Dimensions
32 wireless devices to the system. All devices are spread 288mm x 298mm x 78mm / 11.3” x 11.7” x 3” approximately.
spectrum, 900 MHz, fully supervised devices which use stan- PC500 Cabinet
dard ‘AAA’ or ‘AA’ alkaline batteries. Main control cabinet for the PC580 main panel. Dimensions
Seven devices are available. They are as follows: 213mm x 235mm x 78mm / 8.4” x 9.25” x 3” approximately.
WLS904 Wireless Motion Detector: Adds wireless space pro- PC5004C Cabinet
tection to your system Cabinet to house the PC5400 Printer Module. Dimensions
WLS905 Wireless Universal Transmitter: Adds wireless door 229mm x 178mm x 65mm / 9” x 7” x 2.6” approximately.
or window contacts to your system.
1.3 Out of the Box
WLS906 Wireless Smoke Detector: Adds smoke detection to Please verify that the following components are included in
your system. your system:
WLS907 Wireless Slimline Universal Transmitter: A smaller • one PC5003C main control cabinet
wireless door or window contact. • one PC580 main control circuit board
WLS908 Wireless Panic Pendant: Adds personal protection to • one PC1555RKZ keypad with zone input
the system. When used, the unit will indicate a non-medical emer- • one Installation Manual with programming worksheets
gency to the central station. • one Instruction Manual for the end user
WLS909 Wireless Key : Adds a simple and mobile method of • one hardware pack consisting of:
arming and disarming to the system, as well as one-button access to - one mylar cabinet label
several programmable functions.
- four plastic circuit board standoffs
WLS910 Wireless Handheld Keypad*: A portable keypad - ten 5600Ω (5.6K) resistors
which allows arming and disarming from anywhere on the premises.
- one 2200Ω (2.2K) resistor
PC5400 Printer Module - one 1000Ω (1K) resistor
The PC5400 Printer Module allows the panel to print out all - ground connection assembly
events that occur on the system to any serial printer. The print- - one cabinet door plug
out will contain the time, date and the event that occurred.
LINKS1000 Cellular Communicator*
The LINKS1000 Cellular Communicator can be used three dif-
ferent ways: as the sole communicator for the panel, as a
backup for either or both telephone numbers or as a redun-
dant backup to the land line communicator where the panel
will call both the land line and via the LINKS.
LINKS2X50*
Either the LINKS2150 or LINKS2450 may be used to transmit
alarm information over a long range radio network.
Skyroute Transceiver*
The Skyroute transceiver offers a new wireless method of
communication for the transmission of events using cellemetry
service.

2 *WLS910, LINKS1000, LINKS2X50, and Skyroute have not been investigated by UL.
 S ec tion 2: Ge tti ng Starte d
The following sections provide a thorough description of how Step 10: Testing the System
to wire and configure devices and zones. Test the panel thoroughly to ensure that all features and func-
tions are operating as programmed.
2.1 Installation Steps
Read this section completely before you begin. Once you 2.2 Terminal Descriptions
have an overall understanding of the installation process, Battery Connection
carefully work through each step. A 12V 4Ah rechargeable battery is used as a backup source
Step 1: Create a Layout of power in the event of an AC power failure. The battery also
Draw a rough sketch of the building to get an idea of where all provides additional current when the panel’s demands exceed
alarm detection devices, keypads and other modules are to the power output of the transformer, such as when the panel is
be located. in alarm.
Step 2: Mounting the Panel NOTE:Do not connect the battery until all other wiring is com-
Mount the panel in a dry area close to an unswitched AC plete. Connect the battery before connecting the AC.
power source and the incoming telephone line. Before attach- Connect the RED battery lead to the positive battery terminal;
ing the cabinet to the wall, be sure to press the four circuit connect the BLACK lead to negative.
board mounting studs into the cabinet from the back. After
you have attached the cabinet to the wall, stick the provided AC Terminals – AC
DSC logo sticker on the front of the cabinet. The panel requires a 16.5VAC, 40VA transformer. Connect the
transformer to an unswitched AC source and connect the
NOTE:You must complete all wiring before connecting the bat- transformer to these terminals.
tery, or applying AC to the panel.
NOTE:Do not connect the transformer until all other wiring is
Step 3: Wiring the Keybus (Section 2.3) complete.
Wire the Keybus to each of the modules following the guide-
lines provided in Section 2.3 of this manual. Auxiliary Power Terminals – AUX+ and AUX-
These terminals provide up to 550 mA of additional current at
Step 4: Zone Wiring (Section 2.8) 12 VDC for devices requiring power. Connect the positive side
You must power down the control panel to complete all zone of any device requiring power to the AUX+ terminal, the nega-
wiring. Please refer to 2.8 “Zone Wiring” on page 5 when con- tive side to AUX- (ground). The AUX output is protected. This
necting zones using normally closed loops, single EOL resis- means that if too much current is drawn from these terminals
tors, double EOL resistors, Fire zones and Keyswitch Arming (such as a wiring short), the panel will temporarily shut off the
zones. output until the problem is corrected.
Step 5: Complete Wiring (Section 2.2) Bell Output Terminals – BELL+ and BELL-
Complete all other wiring including bells or sirens, telephone These terminals provide up to 700 mA of continuous current at
line connections, and ground connections following the guide- 12 VDC for powering bells, sirens, strobes or other warning-
lines provided in Section 2.2 (“Terminal Descriptions”). type equipment. Connect the positive side of any alarm warn-
Step 6: Power up the Control ing device to BELL+, the negative side to BELL–. Please note
Once all zone and Keybus wiring is complete, power up the that the Bell output is protected: if too much current is drawn
control panel. First, connect the red battery lead to the posi- from these terminals (such as a wiring short), the Bell PTC will
tive terminal and the black lead to negative. Then, connect the open. Three amps can be drawn for short periods only.
AC. The Bell output is supervised. If no alarm warning devices are
NOTE: Connect the battery before connecting the AC. You in use, connect a 1000Ω resistor across BELL+ and BELL– to
must apply AC power to the panel for at least 10 seconds, or prevent the panel from displaying a trouble condition. For
the panel will not function. The panel will not power up on the more information, please refer to “[*][2] Trouble Display” on
battery connection alone. page 9).
For UL installations, when a bell or
Step 7: Keypad Assignment (Section 2.5) siren is used for fire signaling with a
In order for keypads to be properly supervised, each must be pulsed cadence, it must be con-
assigned to a different slot. Please follow the guidelines pro- nected between the AUX+ and
vided in Section 2.5 when assigning keypads. BELL- terminals. To maintain bell cir-
Step 8: Supervision (Section 2.6) cuit supervision, do not connect
The supervision of each module by the panel is automatically more than one device to the BELL-
enabled upon power up. Please verify that all modules appear terminal. A fire bell or siren used for
on the system according to the instructions in Section 2.6. this application must be UL Listed and have a current con-
Step 9: Programming the System (Sections 4 & 5) sumption of 400mA or less (e.g. Wheelock MT-12/24-R).
Section 4 explains how to program the panel. Section 5 con- Keybus Terminals – AUX+, AUX-, YEL, GRN
tains a complete description of the various programmable fea- The Keybus is used by the panel to communicate with mod-
tures, which options are available and how they function. Fill ules and vice versa. Each module has four Keybus terminals
out the Programming Worksheets completely before attempt- that must be connected to the four Keybus terminals on the
ing to program the system. panel. For more information, see section 2.3 “Keybus Opera-
tion and Wiring” on page 4.

3
Programmable Output Terminals – PGM1 and PGM2 • No module can be more than 1,000'/305m (in wire length)
Each PGM output is designed so that when activated by the from the panel.
panel, the terminal will switch to ground • Shielded wire should not be used.
PGM1 can sink up to 50mA of Example of Keybus Wiring
current. Connect the positive NOTE:
side of the LED or buzzer to Module (A) is correctly
AUX+, the negative side to wired within 1,000'/
PGM1. PGM2 operates simi- 305m of wire from the
larly to PGM1. If more than 50 panel.
mA of current are required, a
Module (B) is correctly
relay must be used.
wired within 1,000'/
Please study PGM wiring in 305m of wire from the
the accompanying diagram. panel.
For a list of the programmable Module (C) is NOT wired correctly as it is further than 1,000'/
output options, please see 305m from the panel, in wire distance.
section 5.11 “PGM Output
Options” on page 20. 2.4 Current Ratings – Modules and Acces-
Zone Input Terminals – sories
Z1 to Z4 In order for the PC580 system to operate properly, the power
Each detection device must be connected to a zone on the output capabilities of the main control and the expansion
control panel. We suggest that one detection device be con- devices must not be exceeded. Use the data presented below
nected to each zone; wiring multiple detection devices to a to ensure that no part of the system is overloaded and cannot
single zone, however, is possible. For zone wiring specifics, function properly.
please see section 2.8 “Zone Wiring” on page 5. PC580 (12 VDC)
Telephone Connection Terminals – TIP, RING, T-1, R-1 AUX+: ........550mA: Subtract the listed rating for each key-
If a telephone line is required for central station communica- pad, expansion module and accessory con-
tion or downloading, connect an RJ-31X telephone jack in the nected to AUX+ or Keybus.
following manner: BELL: .........700mA continuous rating; 3.0A short term. Avail-
able only with standby battery connected.
PC580 Device Ratings (at 12 VDC)
• LCD5500Z Keypad: 85mA max.
• PC1555RKZ Keypad: 85mA max.
• PC5508Z, PC5516Z, PC5532Z Keypads: 85mA max.
• PC5400 Serial Module: 65mA
• PC5132 Wireless Receiver: 125mA

NOTE:Please ensure that all plugs and jacks meet the dimen- Other Devices
sion, tolerance and metallic plating requirements of 47 C.F.R. Please read the manufacturer’s literature carefully to deter-
mine the maximum current requirements for each device—
Part 68, SubPart F. For proper operation, no other telephone
during activation or alarm—and include the proper values for
equipment should be connected between the control panel and
loading calculations. Connected devices must not exceed
the telephone company facilities. Do not connect the alarm
system capabilities during any possible operational mode.
panel communicator to telephone lines intended for use with a
fax machine. These lines may incorporate a voice filter which 2.5 Keypad Assignment
disconnects the line if anything other than fax signals are There are eight available slots for keypads. LED keypads by
detected, resulting in incomplete transmissions. default are always assigned to slot 1. LCD5500Z keypads are
always assigned to slot 8. You will need to assign each key-
2.3 Keybus Operation and Wiring
pad to its own slot (1 to 8). Keypad assignment is required, as
The Keybus is used by the panel to communicate with all con-
it tells the panel which slots are occupied. The panel can then
nected modules and vice versa. The red (AUX+) and black
generate a fault when a keypad supervisory is not present.
(AUX-) terminals are used to provide power, while the yellow
(YEL) and green (GRN) terminals are clock and data respec- NOTE: One LCD keypad must be assigned to slot 8 in order to
tively. upload keypad programming using DLS-1 software.
NOTE: The four Keybus terminals of the panel must be con- How to Assign Keypads
nected to the four Keybus terminals or wires of all modules. Do the following at each keypad installed on the system:
1. Enter [*][8][installer’s code] to go to installer programming
The following restrictions apply to Keybus wiring:
2. Enter [000] for Keypad Programming
• Keybus should be run in minimum 22 gauge quad
3. Enter [0] for Slot Assignment
(0.5mm); two pair twist is preferred.
4. Enter a two digit number (11-18) to specify which supervi-
• The modules should be home-run to the panel but can be sory slot the keypad will occupy.
connected in series or T-tapped. 5. Press [#] twice to exit installer programming.
• Any module can be connected anywhere along the Key- After assigning all keypads, perform a supervisory reset by
bus. You do not need to run a separate Keybus wire for entering section [902] in installer’s programming. The panel
keypads, etc.

4
 G e t t i n g S t a r t e d : 2 . 6 S u p e r v i s i o n

will now supervise all assigned keypads and enrolled modules power it back up. If you do not, the zones may not work cor-
on the system. rectly.
How to Program Function Keys Normally Closed (NC) Loops
By default, the 5 function keys on each keypad are pro-
grammed as Stay Arm (03), Away Arm (04), Chime (06), Sen-
sor Reset (14) and Quick Exit (16). You can change the
function of each key on every keypad:
1. Go to the keypad where you want to change the function
key programming and enter Installer Programming.
2. Press [000] for Keypad Programming.
3. Enter [1] to [5] to select a function key to program. To enable normally closed loops, programming section [013],
4. Enter the 2 digit number, [00] to [17] to select the feature option [1] must be ON.
you want the function key to have. For a complete list of NOTE:This option should only be selected if Normally Closed
Function Key options see section 3.5 “Function Keys” on (NC) detection devices or contacts are being used.
page 11.
5. Continue from step 3 until all function keys are pro- Single End Of Line (EOL) Resistors (5600Ω)
grammed. To enable panel detection of single end of line resistors, pro-
6. To exit Installer Programming, press [#] twice. gramming section [013], options [1] and [2] must be OFF.

2.6 Supervision
By default, all modules are supervised upon installation.
Supervision is enabled at all times so that the panel can indi-
cate a trouble if a module is removed from the system.
To check which modules are currently connected and super-
vised, enter programming section [903] from installer’s pro-
gramming. The LCD keypad will allow you to scroll through the
display of connected modules. A connected module which
does not show as being present will appear as a trouble con-
dition and the Trouble light on the keypad will turn ON. This
condition may be due to one or more of the following reasons:
• the module is not connected to the Keybus
• there is a Keybus wiring problem
• the module is more than 1,000'/305m from the panel NOTE:This option should be selected if either Normally Closed
• the module does not have enough power (NC) or Normally Open (NO) detection devices or contacts are
For more information regarding module supervision troubles, being used.
please refer to “[*][2] Trouble Display” on page 9.
Double End of Line (DEOL) Resistors
2.7 Removing Modules Double End of Line resistors allow the panel to determine if the
The panel must be instructed to no longer supervise a module zone is in alarm, tampered or faulted.
being removed from the system. To remove the module, dis- To enable panel detection of double end of line resistors, pro-
connect it from the Keybus and reset the supervision field by gramming section [013], option [1] must be OFF and option
entering [902] in the installer’s programming. The panel will be [2] must be ON.
reset to recognize and supervise all existing modules on the NOTE: If the Double EOL supervision option is enabled, all
system. hardwire zones on the main panel must be wired for Double
EOL resistors, except for Fire and 24 Hour Supervisory zones.
2.8 Zone Wiring NOTE:Do not wire DEOL resistors on keypad zones.
For a complete description of the operation of all zone types,
please refer to 5.2 “Zone Programming” on page 15. NOTE: Do not use DEOL resistors for Fire zones or 24 Hour
There are several different ways in which zones may be wired, Supervisory zones. Do not wire Fire zones to keypad zone ter-
depending on which programming options have been minals if the DEOL supervision option is selected.
selected. The panel can be programmed to supervise nor-
mally closed, End of Line, or Double End of Line loops. Please
refer to the following diagrams to study each type of individu-
ally supervised zone wiring.
NOTE:Any zone programmed for Fire or 24 Hour Supervisory
must be wired with a single End of Line (EOL) resistor regard-
less of the type of zone wiring supervision selected for the
panel (section [013]: [1] -[2]). See 5.2 “Zone Programming” on
page 15. NOTE: This option can only be selected if Normally Closed
(NC) detection devices or contacts are being used.
NOTE:If you change the zone supervision options from DEOL
to EOL or from NC to DEOL (section [013], options [1] or [2]), NOTE:Only one NC contact can be connected to each zone.
you should power down the system completely, and then Wiring multiple detection devices or contacts on a single loop
is not allowed.

5
The following chart shows zone status under certain condi- LINKS Answer
tions: When using the LINKS1000
Loop Resistance Loop Status cellular communicator, any
0Ω (shorted wire, loop shorted) Fault main board zone may be
5600Ω (contact closed) Secure configured for LINKS
Infinite (broken wire, loop open) Tamper Answer.
11200Ω (contact open) Violated A zone configured for
LINKS Answer allows
End of Line Resistors. . . . . . . . . . . . . . . . . . Section [013]: [1] downloading to be per-
Double End of Line Resistors . . . . . . . . . . . Section [013]: [2] formed in the event of tele-
phone line failure. When
the LINKS receives a tele-
2.9 Fire Zone Wiring phone call, it will activate
NOTE:4-Wire Smoke Detectors the RING terminal on the
All fire zones must be wired according to the following dia- LINKS circuit board. The
gram: zone programmed as
LINKS Answer always
requires a single EOL resis-
tor (5600Ω).
Wire the LINKS Answer zone according to the above diagram.
NOTE: The LINKS Answer zone is only required for download-
ing to the panel via the LINKS.
NOTE: When using the LINKS, Busy Tone Detection must not
be used.
NOTE: Keypad zones cannot be used for 24 Hour Supervisory
or LINKS Answer.

2.11 Keypad Zones

Each “z” keypad on the system has a zone input to which a
2.10 LINKS Zone Wiring* device - such as a door contact - can be connected. This
LINKS Support eliminates the need to run wires back to the control panel for
When using the LINKS1000 every device.
cellular communicator, con- To install the keypad, open the keypad plastic by removing the
nect the LINKS to the main screw at the bottom of the unit. Locate the five terminals on
panel according to the fol- the keypad circuit board. Connect the four Keybus wires from
lowing diagram: the control panel: the red wire to R, the black to B, the yellow
to Y and the green to G.
To connect the zone, run one wire to the Z terminal and the
other to B. For powered devices, use red and black to supply
power to the device. Run the red wire to the R (positive) termi-
nal and the black wire to the B (negative) terminal.
When using end of line supervision, connect the zone accord-
ing to one of the configurations outlined in section 2.8 “Zone
LINKS Supervision (24 Hour Supervisory) Wiring”. End of line resistors must be placed on the device
When using the end of the loop, not at the keypad.
LINKS1000 cellular com- NOTE: Keypad zones do not support DEOL resistors.
municator, any main board
zone may be configured
for LINKS Supervision. Pro-
gram this zone as zone
type [09], 24 Hour Supervi-
sory in section [001].
With a LINKS Supervisory
zone, if the LINKS1000
experiences a trouble, the
zone will be violated, caus-
ing the panel to report the
event to the central station.
This type of zone always
requires a single EOL
resistor (5600Ω).
Wire this zone according to the above diagram.

6 *Not investigated by UL.

 G e t t i n g S t a r t e d : 2 . 1 1 K e y p a d Z o n e s

Assigning Keypad Zones

When using keypad zone inputs, each input used must be
assigned a zone number in Installer’s Programming.
First, ensure that you have enrolled all installed keypads into
the desired slots. (See 2.5 “Keypad Assignment” on page 4.)
Next, enter programming section [020] to assign the zones.
There are eight programming locations in this section, one for
each keypad slot. Enter a 2-digit zone number for each of the
keypad zones. This number must be entered in the location
corresponding to the keypad to which each zone is con-
nected.
Example: The zone on an LCD5500Z keypad in slot 8 is to be
assigned zone 3. In section [020], scroll to option [8] and
enter (03).
NOTE:Keypad zones 1-4 will replace zone terminals Z1-Z4 on
the control panel.
NOTE: Once the keypad zones are assigned, you must also
program zone definitions and zone attributes. (See also 5.4
“Assigning Keypad Zones” on page 17).
NOTE: Keypad zones can only be used for household bur-
glary-initiated devices. Do not place the device more than 3
feet from the keypad. The keypad zone must be tested weekly.

7
 S e c tion 3 : Ke y p ad Co mmand s
Use any system keypad to enter commands and/or program 3.3 Automatic Arming
the PC580 security system. The LED keypad uses function The system can be programmed to Auto-Arm at a specific
and zone indicator lights to represent alarm functions and sta- time every day if it is in the disarmed condition. In order for the
tus. If you have a PC1555RKZ keypad, the System light acts Auto-Arm function to work properly, you must program the cor-
as a Trouble, Memory, Program and Bypass indicator. Unlike rect Time of Day. For programming the clock and auto-arm
other LED keypads, these conditions will only be represented times, see “[*][6] User Functions” on page 10.
by the System light. When the system’s internal clock matches the Auto-Arm Time,
The LCD keypad provides a written description on the liquid the panel will check the system status. If the system is armed,
crystal display and uses function indicator lights to communi- the panel will do nothing until the next day at the auto-arm
cate alarm status to the user. time, when it will check the system again. If the system is dis-
The PC580 Instruction Manual provides basic directions for armed at the auto-arm time, the panel will sound the buzzer of
arming and disarming the system, bypassing zones and per- all keypads for one minute. If the Bell Squawk During Auto
forming user functions from the keypads. The following sec- Arm option is enabled (section [014], option [2]), the bell will
tions provide additional details on these functions. squawk once every 10 seconds while the system is auto-arm-
ing. If a valid access code is entered, auto-arming will be
3.1 Arming and Disarming aborted.
For a description of basic arming and disarming, please see NOTE: If auto-arm is cancelled, the number of the user who
the PC580 Instruction Manual. For other methods of arming, cancelled the auto-arm will be logged in the event buffer.
please refer to “[*][0] Quick Arm”, “[*][9] Arming Without Entry
Delay” and 3.5 “Function Keys” on page 11. If no code is entered, the panel will auto-arm. If a zone is vio-
lated, the panel will transmit a Partial Closing Reporting Code
NOTE: The event buffer will log “Armed in Stay Mode” or
– if programmed – to indicate to the central station that the
“Armed in Away Mode” whenever the system is armed.
system is not secure. If the zone is restored, the panel will add
In an attempt to prevent false alarms, the Audible Exit Fault the zone back into the system.
will notify the user of an improper exit when they arm their sys- NOTE: Auto arming can only be cancelled by entering a valid
tem. If a non force-arming Delay 1 or Delay 2 type zone is left access code at any keypad.
open at the end of the exit delay, the entry delay will begin
immediately and the bell or siren will sound a steady alarm for 3.4 [*] Commands
the entry delay period. At the end of the entry delay period, if The [*] key commands provide an easy way for the user to
the system has not been disarmed it will go into alarm. This access basic system programming – such as programming
feature can be turned OFF in programming section [013], access codes or bypassing zones. The user can also use the
option [6]. (See 5.17 “Arming/Disarming Options” on page [*] key commands to check on the system’s status, including
23.) viewing trouble conditions and displaying the event buffer on
the LCD keypad.
3.2 Auto Bypass – Stay Arming
The [*] key commands can be performed from both LCD and
Stay arming allows the user to arm the system without leaving
LED keypads. The LED keypad uses the zone indicator lights
the premises. All zones programmed as stay/away will be
to display command information. The LCD display provides
bypassed when the user stay arms the system, so that the
written information, guiding the user through each command.
user does not have to bypass interior zones manually. (See
The commands in this section are explained as viewed from
5.2 “Zone Programming” on page 15.)
an LED keypad. When using an LCD keypad, use the arrow
When the system is armed using a valid access code, if any keys (< >) to scroll through information provided. Otherwise,
zones on the system have been programmed as stay/away the functions remain the same for both keypad types.
zones, the Bypass light will turn ON. The panel will then moni-
tor all zones programmed as Delay 1 and Delay 2 zones, such [*][1] Bypassing and Activating Stay/Away Zones
as designated entry/exit doors. If a delay zone is not violated Use the [*][1] keypad command to bypass individual zones. A
by the end of the exit delay, the panel will bypass all stay/away bypassed zone will not cause an alarm.
zones. The Bypass light will remain on to inform the user that NOTE: Zones can only be bypassed when the system is not
the interior zones have been automatically bypassed by the armed.
panel. If a delay zone is violated during the exit delay, the sys- If the Code Required for Bypass option is enabled (section
tem will arm in Away mode and all stay/away zones will be [015], option [5]), only access codes with the bypass attribute
active after the exit delay expires. enabled will be able to bypass zones. (See 5.1 “Programming
The user can arm the stay/away zones at any time by entering Security Codes” on page 15.)
the [*][1] keypad command. (See “[*][1] Bypassing and Acti- If the Bypass Status Displayed While Armed option is cho-
vating Stay/Away Zones” on page 8.) sen, the Bypass (or System) light will be ON while the system
Stay arming can also be initiated by pressing and holding the is armed to indicate any bypassed zones. (See 5.17 “Arming/
Stay function key for two seconds on the PC5508Z and Disarming Options” on page 23.)
LCD5500Z keypads, if programmed by the installer. For more
NOTE: When you disarm the system, all manually-bypassed
information regarding Stay arming, please see 3.5 “Function
zones will be unbypassed.
Keys” on page 11.

8
 K e y p a d C o m m a n d s : 3. 4 [ *] C om m a n ds

Activate Stay/Away Zones To view trouble conditions from an LED keypad:

If the system is armed in stay mode, the [*][1] command can 1. Press [*][2].
be used to activate the stay/away zones. 2. The keypad will flash the Trouble (or System) light. The
[*][2] Trouble Display zone indicator lights corresponding to the present trouble
The panel constantly monitors itself for several different trou- conditions will be ON.
ble conditions. If a trouble condition is present, the Trouble (or When using an LCD keypad, the trouble conditions will be
System) light will be on and the keypad will beep twice every listed on the display. Use the arrow (< >) keys to scroll through
10 seconds. The trouble beep can be silenced by pressing the list of present trouble conditions.
any key on any keypad. If Bell Squawk on Trouble is enabled NOTE:Troubles can be viewed while armed using the LCD key-
(section [014], option [5]), the bell will squawk every 10 sec- pad, provided the keypad is version 2.0 or later. Older keypads
onds when a trouble condition is present. will incorrectly display “Fire Trouble”. If using older LCD key-
pads, programming section [013], option [3] as OFF will ensure
troubles are displayed correctly.
The various troubles are described below:

Light Trouble
1 Service Required: Press [1] to determine the specific trouble. Lights 1 - 5 will light up to indicate the trouble:
• Light [1] Low Battery: Main panel backup battery charge is low (below 11.5 volts under load).Trouble is restored
when the battery charges over 12.5 volts.
• Light [2] Bell Circuit Trouble: The bell circuit is open (see section 5.13 “Bell” on page 22).
• Light [3] General System Trouble: The printer connected to the PC5400 Printer module has a fault and is off-line.
• Light [4] General System Tamper: Tamper has been detected in a module.
• Light [5] General System Supervisory: The panel has lost communication with a module connected to the Keybus
(see section 2.6 “Supervision” on page 5). The event buffer will log the event.
NOTE: All tamper conditions must be physically restored before the trouble condition will clear.
NOTE:Lights [6-8] – Not used
2 AC Failure: AC power is no longer being supplied to the control panel. The Trouble (or System) light will flash if an AC
Failure is present, if the Trouble Light Flashes if AC Fails option is programmed (section [016], option [2]). This trouble
will not be displayed if the AC Trouble Displayed option is disabled (section [016], option [1]). See section 5.8 “Com-
municator – Reporting Codes” on page 18 for information on AC trouble reporting.
3 Telephone Line Monitoring Trouble (TLM): There is a problem with the telephone line (See section 5.12 “Tele-
phone Line Monitor (TLM)” on page 22.)
4 Failure to Communicate (FTC): The communicator failed to communicate with any of the programmed telephone
numbers (see section 5.5 “Communicator – Dialing” on page 17).
5 Zone Fault (including Fire Zone): A zone on the system is experiencing trouble, meaning that a zone could not
provide an alarm to the panel if required to do so (e.g. a fire zone is open, or there is a short on a DEOL zone, or a super-
visory fault on a wireless zone). When a zone fault trouble condition occurs, the keypad(s) on the system will start to
beep. Press [5] while in Trouble mode to view the affected zones.
NOTE: A Fire zone trouble will be generated and displayed in the armed state.
6 Zone Tamper: A zone configured for Double End Of Line resistor supervision has a tamper condition, or the tamper
switch is open on a wireless device. When a tamper condition occurs, the keypad(s) will start to beep. Press [6] while in the
Trouble mode to view the affected zones. If a zone is tampered or faulted, it must be fully restored to clear the trouble.
NOTE: By enabling Tampers/Faults Do Not Show as Open in section [013], option [4], Faults and Tampers will not show
as open on the keypad, and will be hidden from the end user. If the option is disabled, Faults and Tampers will be dis-
played on the keypad
NOTE:Once a zone is tampered or faulted, it must be completely restored before the trouble condition will clear.
7 Device Low Battery: A wireless device has a low battery condition. Press [7] one, two, or three times to view which
devices are experiencing battery failure. An LED keypad will indicate battery failure using zone lights 1 to 8. The follow-
ing will occur:
Keypad beeps: Keypad displays:
Press [7] 1 Zones with low batteries (LED keypad - zone lights 1 to 32)
Press [7] again 2 Handheld keypads with low batteries (LED keypad - zone lights 1 to 4)
Press [7] again 3 Wireless keys with low batteries (LED keypad - zone lights 1 to 8)
To view the battery conditions of wireless keys 9 through 16, you must use an LCD keypad.
8 Loss of System Time: When the panel is powered up, the internal clock needs to be set to the correct time. This
trouble is cleared when an attempt is made to reset the clock.

[*][3] Alarm Memory [*][4] Door Chime On/Off

The Memory (or System) light will be on if any alarm occurred The door chime feature is used to sound a tone from the key-
during the last armed period or – in the case of 24 hour zones pad whenever a zone programmed as a chime zone is acti-
– if an alarm occurred while the panel was disarmed. vated. (See 5.3 “Zone Attributes” on page 16.) If the door
To view alarm memory, press [*][3]. The keypad will flash the chime feature is enabled, the keypad will emit five short beeps
Memory (or System) light and the zone indicator lights corre- whenever a chime zone is activated. Designated entry/exit
sponding to the alarm or tamper conditions which occurred doors are often defined as chime zones. The feature can be
during or since the last armed period. To clear the Memory (or turned on or off while the system is armed or disarmed.
System) light, arm and disarm the system.

9
[*][5] Programming Access Codes [*][6] User Functions
There are 37 access codes available to the user. They are: This command can be used to program several different func-
Access code (40) ..................... One master code tions:
Access codes (01)-(32)............ 32 general access codes To program User Functions:
Access codes (33)-(34)............ Two duress codes 1. Press [*][6][Master Code]. The Program (or System) light
Access codes (41)-(42)............ Two supervisor codes will flash.
All access codes have the ability to arm or disarm the system 2. Press the number [1] to [6] for the item to be programmed.
and can activate the PGM Outputs using the [*][7] com- • [1] – Time and Date
mands. The time and date must be accurate for the auto-arm or
For a description of how to program access codes from LCD test transmission functions to work properly and for the
or LED keypads, see the PC580 Instruction Manual. event buffer to time and date stamp all events.
- Enter the time (hour and minute) using 24hr format [HH
Master Code – Access Code (40) MM] from 00:00 to 23:59.
This code can be used to program all access codes. The - Enter the date by month, day and year [MM DD YY].
Master code has all Access Code Attributes enabled by • [2] – Auto-Arm Enable/Disable
default, so that the Master code can be used to perform any To enable or disable auto-arming, press [2]. The keypad
keypad function. Master code attributes cannot be changed. will sound three short beeps when auto-arm is enabled
If the Master Code Not Changeable option is enabled, (sec- and one long beep when disabled. For more information,
tion [015], option [6]) the Master Code can only be changed see 3.3 “Automatic Arming” on page 8.
by the Installer.
• [3] – Auto-Arm Time
General Access Codes – Access Codes (01) to (32) The system can be programmed to arm automatically at a
General access codes can arm and disarm the system. When pre-set time. When programming the auto-arm time, enter
the Code Required for Bypassing option is enabled, users the time (hour and minute) using 24hr format [HH MM]. For
will need to enter a valid access code when bypassing zones. more information, see 3.3 “Automatic Arming” on page 8.
Individual access codes can have the Zone Bypassing • [4] – System Test
attribute disabled under Access Code Attribute programming. When [4] is pressed the panel will test the bell output, key-
For more information regarding access code options, please pad lights and the communicator for two seconds. The
see 5.1 “Programming Security Codes” on page 15. panel will also send a System Test Reporting code, if pro-
Duress Code – Access Code (33) and (34) grammed. (See 5.8 “Communicator – Reporting Codes” on
Duress codes will send a duress reporting code to the central page 18.)
station when entered. • [5] – Enable DLS (Downloading)
NOTE: If a duress code is programmed, when it is used, the When [5] is pressed, the panel will enable the downloading
panel will always send a reporting code to the central station, option for six hours. During this time, the panel will answer
even if the attributes of the duress code are turned off. incoming downloading calls. (See 5.10 “Downloading” on
page 20.)
Supervisor Codes – Access Code (41) and (42) • [6] – User Initiated Call-Up
These codes can be used to program general access and When [6] is pressed, the panel will initiate a call to the
duress codes. The two supervisor codes have all attributes on downloading computer.
by default. These settings can be changed.
Additional Features Available from the LCD Keypad
Access Code Attributes Additional features, including access to the event buffer, are
There are three access code attributes which can be pro-
available using the LCD keypad. Use the arrow keys (< >) to
grammed for each code. scroll through the [*][6] menu and press the [*] key to select
To program each attribute, enter [*][5][Master Code][9] to the following commands:
enter the attribute programming mode. Then enter the code
number [01-32,33,34,41,42]. Enter the attribute number: Viewing the Event Buffer from an LCD Keypad
Select “View Event Buffer” from the [*][6] menu. The keypad
Attribute [1].......... User enabled for arming, disarming, alarm
will display the event, event number, time and date along with
reset, [*][7][1-2] options, auto arm cancel-
the zone number and access code, if applicable. Press [*] to
lation
toggle between this information and the event itself. Use the
Attribute [2].......... Not used arrow keys (<>) to scroll through the events in the buffer.
Attribute [3].......... Zone bypassing enabled When you have finished viewing the event buffer, press [#] to
Attribute [4]-[6] .... Not used exit.
Attribute [7].......... Bell squawk on access code entry Brightness Control
Example: You can use the arm/disarm bell squawk attribute to You can select from 10 different backlighting levels. Use the
have wireless key access codes squawk the bell, while other arrow keys (< >) to scroll to the desired backlighting level.
codes are silent. To do this, enable attribute [7] on all access Press [#] to exit.
codes associated with wireless keys.
Contrast Control
NOTE: If you enable the Bell Squawk on Arming/Disarming You can select from 10 different display contrast levels. Use
(section [014], option [1]), the bell will sound arm/disarm bell the arrow keys (< >) to scroll to the desired contrast level.
squawks for all access codes, regardless of the programming Press [#] to exit.
for attribute [7]. See 5.17 “Arming/Disarming Options” on
page 23. Keypad Sounder Control
You can select from 21 different keypad tones. Use the arrow
NOTE: Master code attributes cannot be changed. keys (< >) to scroll to the desired keypad sound level and

10
 K e y p a d C o m m a n d s : 3 . 5 F u nc t io n K e y s

press [#] to exit. This feature can be accessed on LED key- If the Quick Arm option is disabled (section [015], option [4]),
pads by pressing and holding the [*] key. users will need to enter an access code after pressing a func-
[*][7] Command Output Functions tion key.
The user can activate programmable output functions using NOTE:On the PC1555RKZ keypad, use number keys 1 - 5 for
the [*][7][1-2] commands. The outputs may be activated when the function keys.
the system is either armed or disarmed. “Stay” – (03) Stay Arm
[*] [7] [1] – Command Output Option #1: The system will arm in the Stay mode (see 3.2 “Auto Bypass –
Press [*] [7] [1] [Access Code, if required] to activate outputs Stay Arming” on page 8). Enable the Quick Arm feature (pro-
programmed as PGM output option [19]. This output can be gramming section [015], option [4]) to have this key function
used for operating devices such a garage door opener, light- without the need to enter an access code. If Quick Arm is not
ing or door strikes. enabled, the user will have to enter an access code before the
[*][7][2] – Command Output Option #2: system will stay arm.
Press [*][7][2][Access Code, if required] to activate all outputs “Away” – (04) Away Arm
programmed as one of PGM output options [03] or [20]. The system will arm in the Away mode (see 3.2 “Auto Bypass
Special Note: Traditionally, [*][7][2] has been reserved for – Stay Arming” on page 8). Enable the Quick Arm feature (pro-
resetting smoke detectors. Smoke detectors should now be gramming section [015], option [4]) to have this key function
programmed as output [03] “Sensor Reset” . If using output without the need to enter an access code. If Quick Arm is not
option [03], do not program [20] Command Output Option #2. enabled, the user will have to enter an access code before the
Please see 5.11 “PGM Output Options” on page 20 for more system will away arm.
information. When the panel is being Away armed, users can restart the
[*][8] Installer’s Programming exit delay once, by pressing the Away button before the exit
Enter [*][8] followed by the Installer’s Code to access delay expires. This will not work if the panel is being Stay
Installer’s Programming. See sections 4 and 5 for more infor- armed.
mation. “Chime” – (06) Door Chime On / Off
[*][9] Arming Without Entry Delay The Door Chime feature will turn ON or OFF. (See “[*][4] Door
When the system is armed with the [*][9] command, the panel Chime On/Off” on page 9.)
will cancel the entry delay. Delay 1 and Delay 2 type zones will “Reset” – (14) Sensor Reset or [*][7][2]
be instant and Stay/Away zones will be bypassed as soon as The panel will activate all PGM outputs programmed as option
the exit delay has ended (see section 5.2 “Zone Program- [03] Sensor Reset or [20] Command Output Option #2. (See
ming” on page 15). The user must enter a valid access code “[*][7] Command Output Functions” .)
after pressing [*][9]. “Exit” – (16) Activate Quick Exit
[*][0] Quick Arm The panel will activate the Quick Exit feature (See “[*][0]
If the Quick Arm option is enabled (section [015], option [4]), Quick Exit” on page 11.)
enter [*][0] to arm the panel without an access code. (See Additional Function Key Options
5.17 “Arming/Disarming Options” on page 23.) If the Quick The programming of any function key on any keypad may be
Arm option is disabled, users will need to enter an access changed to one of the options listed below. (See 2.5 “Keypad
code after pressing a function key. Assignment” on page 4 for instructions on changing function
NOTE: Quick Arm cannot be used to cancel auto arm. key programming.) Each option is listed according to the pro-
[*][0] Quick Exit gramming code, followed by the corresponding [*] key com-
The Quick Exit function, if enabled, will allow someone to mand. For more information regarding each function, please
leave an armed premises through a Delay type zone without refer to the appropriate part of Section 3.4, “[*] Commands”.
having to disarm and re-arm the system. (See 5.17 “Arming/ [00] Null Key: The key is not used and will perform no
Disarming Options” on page 23.) function when pressed.
When [*][0] is entered, the panel will provide a two minute win- [01]-[02] For future use
dow for the user to exit the premises. During this time, the [03] Stay Arm: As described above.
panel will ignore only one activation of a Delay zone. When the [04] Away Arm: As described above.
Delay zone is secured, the panel will end the two minute quick [05] [*][9] No-Entry Delay Arm: A valid access code
exit delay. must also be entered.
If a second Delay zone is tripped, or if the zone is not restored [06] [*][4] Door Chime On / Off: As described above.
after two minutes, the panel will begin entry delay 1. [07] [*][6][----][4] System Test: A valid master code must
NOTE: If the Exit Delay is in progress, performing a Quick Exit also be entered.
will not extend the Exit Delay. [08] [*][1] Bypass Mode: A valid access code may need
to be entered.
3.5 Function Keys [09] [*][2] Trouble Display
There are five function keys on each keypad labelled Stay,
[10] [*][3] Alarm Memory
Away, Chime, Reset and Exit. Each of these keys is pro-
[11] [*][5] Programming Access Codes: A valid master
grammed by default to perform one of the functions described
code must also be entered.
below. Press and hold the appropriate key for two seconds to
activate a function. [12] [*][6] User Functions: A valid master code must also
be entered.

11
[13] [*][7][1] Command Output Option #1: A valid
access code may need to be entered.
[14] [*][7][2] Reset (Command Output Option #2): As
described above.
[15] For future use
[16] [*][0] Quick Exit: As described above.
[17] [*][1] Reactivate Stay/Away Zones
[18] - [20] For future use

3.6 Features Available for the LCD5500Z

These features are only available for LCD5500Z keypads with
zone inputs:
Automatic Scrolling of Alarms in Memory
The LCD5500Z keypad allows automatic scrolling through
alarms in memory while the keypad is idle. This feature, if
enabled, will override the clock display. This option can be
programmed in LCD programming section [66], option [4].
24 Hour Time Display Option
The LCD5500Z can be programmed to display time using a
24- hour clock, instead of a 12-hour, am/pm clock. This option
can be programmed in LCD programming section [66], option
[3].
Keypad Zones
See 2.11 “Keypad Zones” on page 6.
Viewing Troubles While Armed
See “[*][2] Trouble Display” on page 9 for information on how
to view troubles.
Backlighting Boost
The LCD5500Z, PC55XXZ and PC1555RKZ zone input key-
pads will provide extra number pad lighting when any key is
pressed. The backlighting boost will last for an additional 30
seconds after the last keypress.

12
 S e c tion 4: Ho w to P ro g ram
The following section of the manual describes the Installer’s 4.2 Programming Decimal Data
Programming function and how to program the various sec- A set number of programming boxes are allotted for each sec-
tions. tion requiring decimal data (e.g.: codes, telephone numbers).
NOTE: Read the following section of the manual very carefully If a digit is entered for each program box, the panel will auto-
before you begin programming. We also recommend filling out matically exit from the selected programming section. The
the Programming Worksheets section before you program the Ready light will turn OFF and the Armed light will turn ON.
panel. On the PC1555RKZ and PC5508Z keypads, you can also
press the [#] key to exit a programming section without enter-
For your reference, the corresponding programming sections ing data for every box. This is handy if you only need to
for the functions listed are highlighted in text boxes such as change digits in the first few programming boxes. All other
this one. digits in the programming section will remain unchanged.

4.3 Programming HEX Data

4.1 Installer’s Programming On occasion, hexadecimal (HEX) digits may be required. To
Installer’s Programming is used to program all communicator program a HEX digit press the [*] key. The panel will enter
and panel options. The Installer’s Code is [5555] by default HEX programming and Ready light will begin to flash.
but should be changed to prevent unauthorized access to
The following are the numbers which should be pressed to
programming.
enter the appropriate HEX digit:
Installer’s Code. . . . . . . . . . . . . . . . . . . . . . . . . Section [006] 1=A 2=B 3=C 4=D 5=E 6=F
Once the correct HEX digit has been entered, the Ready light
From an LED Keypad: will continue to flash. If another HEX digit is required, press the
1. Enter [*][8][Installer’s Code]. corresponding number. If a decimal digit is required, press the
The Program light (or System light on the PC1555RKZ) will [*] key again. The Ready light will turn on and the panel will
flash to indicate that you are in programming mode. return to regular decimal programming.
The Armed light will turn on to indicate that the panel is Example:
waiting for the three-digit programming section number. To enter ‘C1’ for a closing by user 1, you would enter:
2. Enter the three-digit section number corresponding to the
[*][3][*], [1]:
section you wish to program.
• [*] to enter Hexadecimal mode (Ready light flashes)
The Armed light will turn off.
• [3] to enter C
The Ready light will turn on to indicate that the panel is
waiting for the information required to complete program- • [*] to return to decimal mode (Ready light is solid)
ming the selected section. • [1] to enter digit 1
3. Enter the information required to complete section pro- NOTE: If Ready light is flashing, any number you enter will be
gramming (i.e.: numbers, HEX data, or ON/OFF options). programmed as the HEX equivalent.
NOTE: If the three-digit section number entered is invalid, or if If you are using a pulse communications format, a decimal
the module which pertains to the section is not present, the zero [0] does not transmit. Programming a zero [0] tells the
keypad will sound a two second error tone. panel not to send any pulses for that digit. Decimal zero [0] is
From an LCD Keypad: a filler digit. To transmit a zero [0], it must be programmed as
1. From any keypad, enter [*][8][Installer’s Code]. The Key- a Hexadecimal ‘A’.
pad will display ‘Enter Section’ followed by three dashes. Example:
2. Enter the three-digit number corresponding to the pro- For the three digit account number ‘403’, you would enter:
gramming section number you wish to program. The key- [4], [*][1][*][3], [0]:
pad will now display the information required to complete • [4] to enter the digit 4
programming the selected section. • [*] to enter Hexadecimal mode (Ready light flashes)
3. Enter the information required to complete section pro- • [1] to enter A
gramming (i.e.: numbers, HEX data, or ON/OFF options). • [*] to return to decimal mode (Ready light is solid)
If you enter information into a section and make a mistake, • [3] to enter the digit 3
press the [#] key to exit the section. Select that section again • [0] to enter the digit 0 as a filler digit.
and re-enter the information correctly.
NOTE: There must be one digit in each box in the program-
ming section in order for the change to be valid.

13
4.4 Programming Toggle Option Sections The keypad displays the information using a binary format,
Some programming sections contain several toggle options. according to the following chart: See Hex data
The panel will use zone lights 1 through 8 to indicate if the dif- entry instructions
ferent options are enabled or disabled. Press the number cor-
responding to the option to turn it ON or OFF. Once all the
toggle options have been selected correctly, press the [#] key
to exit the section and save the changes. The Ready light will
turn OFF and the Armed light will turn ON.
Refer to the Programming Worksheets in this manual to deter-
mine what each option represents and whether the light
Press any of the Emergency Keys (Fire, Auxiliary or Panic) to
should be ON or OFF for your application.
advance to the next digit. When all the digits in a section have
4.5 Viewing Programming been viewed, the panel will exit the section; the Ready Light
will turn OFF and the Armed light will turn ON, waiting for the
LED Keypads next three-digit programming section number to be entered.
Any programming section can be viewed from an LED key- Press the [#] key to exit the section
pad. When a programming section is entered, the keypad will
immediately display the first digit of information programmed LCD Keypad
in that section. When a programming section is entered, the keypad will
immediately display all the information programmed in that
section. Use the arrow keys (< >) to scroll through the data
being displayed. Scroll past the end of the data displayed or
press the [#] key to exit the section.

14
 S e c tion 5 : Pro gram De s cri p ti o ns
The following section explains the operation of all programma- should be disarmed. If the panel is disarmed before the entry
ble features and options and provides a summary of all corre- time expires, no alarm will be generated.
sponding programming locations. [02] Delay 2 Zone
The Delay 2 entry delay time can be set independently of
5.1 Programming Security Codes Delay 1 in programming section [005] (System Times).
There are three codes which can be programmed by the
installer in the Installer’s Programming function: the Master [03] Instant Zone
code, the Installer’s code, and a Maintenance code. All other This zone type will cause an instant alarm if it is violated when
access codes can be programmed through the [*][5] com- the panel is armed. Typically, this zone is used for windows,
mand. (See “[*][5] Programming Access Codes” on page 10.) patio doors or other perimeter zones, and glass break detec-
tors.
The master code can also be programmed by the user as
access code (40). If the Master Code Not Changeable option [04] Interior Zone
is enabled, the system master code can only be changed by This zone will not cause an alarm if violated during the entry
the installer. delay. If the zone is violated before the entry delay has begun,
The Maintenance code can only be used to arm and disarm it will cause an instant alarm. Typically, this zone is used for
the system. The Maintenance code cannot bypass zones, use interior protection devices, such as motion detectors.
[*][9] to arm the system, cancel autoarming, or perform [*][7] [05] Interior Stay/Away Zone
command functions. There will be no arm/disarm bell This zone type works similarly to the Interior zone type, except
squawks when the Maintenance code is used. that it will be automatically bypassed under the following con-
General access codes can arm and disarm the system. When ditions:
the Code Required for Bypassing option is enabled, users • When the panel is armed in the Stay Mode. (See 3.5 “Func-
will need to enter a valid access code when bypassing zones. tion Keys” on page 11.)
Individual access codes can have the Zone Bypassing • When the panel is armed without entry delay. (See “[*][9]
attribute disabled under Access Code Attribute programming. Arming Without Entry Delay” on page 11.)
(See “[*][5] Programming Access Codes” on page 10.) • When the panel is armed with an access code and a Delay
If the 6-Digit User Access Codes option is enabled, all the type zone is NOT tripped during the exit delay.
access codes may be programmed with six digits instead of The automatic bypass prevents the user from having to manu-
four, with the exception of the Panel ID code and the Down- ally bypass interior type zones when arming at home. This
loading Access Code. zone is typically used for interior protection devices, such as
motion detectors.
Installer’s Code. . . . . . . . . . . . . . . . . . . . . . . . . Section [006]
Master Code. . . . . . . . . . . . . . . . . . . . . . . . . . . Section [007] [06] Delay Stay/Away Zone
Maintenance Code . . . . . . . . . . . . . . . . . . . . . . Section [008] This zone type will operate similarly to Interior Stay/Away
Master Code Not Changeable . . . . . . . . . . Section [015]: [6] zones, except that it will always provide an entry delay. Typi-
Code Required for Bypassing . . . . . . . . . . Section [015]: [5] cally, this zone is used for interior protection devices, such as
6-digit User Access Codes . . . . . . . . . . . . Section [701]: [5] motion detectors. This zone option will help prevent false
alarms since it always provides an entry delay time for the
user to turn off the panel.
5.2 Zone Programming NOTE: Hardwire motion detectors covering entry/exit doors
Zones 1-8 are enabled by default. Disable unused zones, or that are using wireless transmitters must be programmed as
enable additional zones in programming sections [202] - Delay Stay/Away. If not, the panel may see the motion detector
[205]. violation before the entry/exit transmitter has time to transmit to
The zone definitions describe how each of the zones you use the receiver, causing a false alarm.
will operate. Program a two-digit code describing the zone
definition in sections [001] - [004]. Select a definition from the [07] Delayed 24 Hour Fire Zone
list below. NOTE:Do not wire Fire zones on keypad zone terminals if the
In addition, each zone has eight different attributes which may DEOL supervision option is enabled for the panel (section
be programmed in sections [101] to [108]. (See 5.3 “Zone [013], option [2]).
Attributes” on page 16.) When this zone is violated, the alarm output will be immedi-
Zone Definitions ately activated (pre-alert) but the communicator will be
delayed for 30 seconds. If the user presses any key on any
[00] Null Zone
keypad during this delay, the alarm output and the communi-
The zone is vacant. Unused zones should be programmed as
cator will be delayed an additional 90 seconds, giving the
Null zones.
user time to correct the problem. If the zone is still violated
[01] Delay 1 Zone after the 90 second delay, the panel will sound the alarm out-
This zone type, normally used for entry/exit doors, can be vio- put and delay the communicator for 30 seconds.
lated during the exit delay time without causing an alarm. If the user does not press a key during the 30 second pre-
Once the exit delay has expired, opening the zone will start alert, the alarm output will latch and the panel will communi-
the entry delay timer. During the entry delay time, the keypad cate the alarm to the central station. The alarm will sound until
buzzer will sound steadily to advise the user that the system

15
the Bell Cutoff time expires (Section [005] “System Times”), or [23] Maintained Keyswitch Arm Zone
until a code is entered. (See 5.13 “Bell” on page 22.) When this zone is violated, the system will arm. When this
NOTE:If a second Fire type zone is violated or if the Fire keys zone is secured, the system will disarm.
are pressed during the delay period, the panel will latch the [24] LINKS Answer Zone
alarm output and will immediately communicate the alarm. Downloading can be performed via the LINKS1000 Cellular
A violated Fire zone will be displayed on all keypads and can Communicator (if used) when the conventional telephone line
be delayed at any keypad. Typically this zone is used for is disconnected. If this operation is desired, connect the RING
latching smoke detectors. terminal of the LINKS1000 to a LINKS Answer zone. (See 2.10
“LINKS Zone Wiring*” on page 6.) Refer to the LINKS1000
[08] Standard 24 Hour Fire Zone Installation Manual for more information.
NOTE:Do not wire Fire zones on keypad zone terminals if the NOTE:Do not wire LINKS Answer zones on keypad zone ter-
DEOL supervision option is enabled for the panel (section minals.
[013], option [2]).
[25] Interior Delay Zone
When this zone is violated, the panel will immediately latch the This zone type is normally used with motion detectors and has
alarm output and communicate to the central station. The a standard exit delay time.
alarm will sound until the Bell Cutoff time expires (Section
If the panel is Away armed (a delay zone is violated during the
[005] “System Times”), or until a code is entered. (See 5.13
exit delay, or the Away function key is used), the Interior Delay
“Bell” on page 22.)
zone will work the same as the Interior zone [04].
A violated Fire zone will be displayed on all keypads. Typically
If the panel is Stay armed (a delay zone is NOT violated dur-
this zone is used for pull stations.
ing the exit delay, the Stay key is used, or [*][9] is used for
[09] 24 Hour Supervisory Zone arming), a violation of the zone will initiate Entry Delay 1.
If this zone is violated when the system is either armed or dis-
[87] Delayed 24 Hour Fire (Wireless)
armed, the panel will report to the central station, and will log
This zone type operates the same as [07] Delayed 24 Hour
the zone alarm to the event buffer. This zone gives a silent
Fire Zone and must be used if the smoke detector is wireless.
alarm by default.
[88] Standard 24 Hour Fire (Wireless)
NOTE:Do not wire 24-Hour Supervisory zones on keypad zone
This zone type operates the same as [08] Standard 24 Hour
terminals.
Fire Zone and must be used if the smoke detector is wireless.
[10] 24 Hour Supervisory Buzzer Zone
If this zone is violated when the system is either armed or dis- Zone Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [001]
armed, the panel will immediately latch the keypad buzzer Zone Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [202]
until a valid access code is entered and will immediately com-
municate to the central station. 5.3 Zone Attributes
[11] 24 Hour Burglary Zone NOTE: All zones, with the exception of 24 Hour and Fire, will
If this zone is violated when the system is either armed or dis- provide an exit delay.
armed, the panel will immediately latch the alarm output and
communicate to the central station. The alarm will sound until NOTE: Do not change the attributes for Fire Zones from the
the Bell Cutoff time expires (Section [005] “System Times”), or default settings.
until a code is entered. (See 5.13 “Bell” on page 22.) Additional zone attributes can be programmed to customize
[12] - [20] the operation of a zone for a specific application. The follow-
The following zone definitions operate similar to the 24 Hour ing attributes are programmable for each zone:
Burglary except for the System Event output type and the SIA • Audible / Silent – This attribute determines whether or not
identifier: the zone will activate the alarm output.
[12] 24 Hour Holdup Zone - This zone gives a silent alarm by • Pulsed / Steady – This attribute determines whether the
default. alarm output will be steady or will pulse on and off every
[13] 24 Hour Gas Zone second.
[14] 24 Hour Heating Zone (N/C zone) • Activate Chime – This attribute determines whether or not
[15] 24 Hour Medical Zone the zone will activate the chime feature. (See “[*][4] Door
Chime On/Off” on page 9.)
[16] 24 Hour Panic Zone
• Bypass Enable – This attribute determines whether or not
[17] 24 Hour Non-Medical Emergency Zone
the zone can be manually bypassed. (See “[*][1] Bypass-
[18] 24 Hour Sprinkler Zone ing and Activating Stay/Away Zones” on page 8.)
[19] 24 Hour Water Flow Zone • Force Arm Enable – This attribute determines whether or
[20] 24 Hour Freezer Zone not the system can be armed while a zone is violated. At
[21] 24 Hour Latching Tamper the end of the exit delay, if this type of zone is violated, it
If this zone is violated, the installer must enter Installer’s Pro- will be ignored by the panel. Once the zone is secured, it
gramming before the system can be armed. will be monitored by the system. This zone attribute, for
example, will allow the user to arm the system with the
NOTE: Wireless zones should not be programmed as zone
garage door open. Later, when the door is closed, it will be
types [22] - [24].
armed along with the rest of the system. Do not program
[22] Momentary Keyswitch Arm Zone this attribute for 24Hr zones.
Momentary violation of this zone will alternately arm/disarm The Force Arm attribute is not recommended for UL
the system. installations.

16
 P r o g r a m D e s c r i p t i o n s : 5. 4 A s s ig n in g K e y p a d Z o ne s

• Swinger Shutdown Enable – This attribute determines NOTE:Contact your local telephone company to confirm which
whether or not the panel will shut down the communicator settings should be used.
and bell for a zone once its swinger limit has been
reached. (See 5.19 “Swinger Shutdown” on page 24.) DTMF or Pulse Dialing . . . . . . . . . . . . . . . . .Section [380]: [3]
• Transmission Delay Enable – This attribute determines Switch to Pulse Dialing on Fifth Attempt . . .Section [380]: [4]
whether or not the panel will delay communicating the alarm Communicator Enable/Disable . . . . . . . . . .Section [380]: [1]
reporting code for the programmed Transmission Delay Communicator Call Direction Options . . . Section [361]-[368]
Period. (See 5.15 “Transmission Delay” on page 23.) Busy Tone Detection . . . . . . . . . . . . . . . . . .Section [701]: [6]
• Wireless Zone – This attribute determines which zones Maximum Dialing Attempts . . . . . . . . . . . . . . . . Section [160]
are to have wireless devices. This allows the panel to gen- Post Dial Wait for Handshake . . . . . . . . . . . . . . Section [161]
erate a low battery trouble and zone supervisories for the
wireless zones. 5.6 Communicator – Account Numbers
NOTE: Any zone with the wireless attribute enabled will not The account number is used by the central station to distin-
cause an alarm for a fault condition when armed (or any time guish between panels. There are two account numbers pro-
for 24-hour zones). grammable for the PC580.

Zone Attributes . . . . . . . . . . . . Sections [101] - [108]: [1] - [8] First Account Code (4 digits). . . . . . . . . . . . . . . Section [310]
Second Account Code (4 digits) . . . . . . . . . . . Section [311]
5.4 Assigning Keypad Zones
“Z” keypads have zone inputs to which devices—such as 5.7 Communicator – Telephone Numbers
door contacts—can be connected. (See 2.11 “Keypad Zones” The panel can use three different telephone numbers for com-
on page 6 for wiring information.) municating with the central station. The First Telephone
Once the keypad zones are installed, assign the zone in pro- Number is the primary number, the Second Telephone Num-
gramming section [020] Keypad Zone Assignments. ber is the secondary number and the Third Telephone Num-
Enter the 2 digit zone designated for each keypad (slot) from ber will back up the First telephone number if enabled.
01-08. NOTE:The Third Telephone Number will NOT back up the Sec-
ond Telephone Number.
Keypad Zone Assignments . . . . . . . . . . . . . . . . . . . . . . [020]
NOTE: If you enter a telephone number section (sections [301]
- [303]) at an LED keypad, pressing [#] will delete the pro-
5.5 Communicator – Dialing grammed telephone number and change all the digits to [F].
If the Communicator Disable option is selected, the panel
If the Alternate Dial option is enabled, the panel will alternate
will not attempt to call central station. If communication is
between the first and third telephone numbers when attempt-
enabled, the panel will attempt to call central station when an
ing to call the central station. If the option is disabled, the
event with a valid reporting code occurs. (See 5.8 “Communi-
panel will only attempt to call the Third telephone number after
cator – Reporting Codes” on page 18.)
failing to communicate with the first telephone number.
The Communicator Call Direction options are used to select
which telephone number the panel will dial when an event NOTE:To use the Third Telephone Number, you must enable it
occurs. in section [380], option [5], and program it in section [303].
If the DTMF Dialing option is enabled, the panel will dial using NOTE:Telephone numbers can be up to 32 digits. This allows
DTMF (touch tone). If the Switch to Pulse Dial option is you to add special digits if required. To program the telephone
enabled, the panel will switch to pulse dialing on the fifth number, enter the numbers 0 through 9 as required. The fol-
attempt to call the central station. When this option is dis- lowing is a list of programmable HEX digits and the functions
abled, the panel will always dial using DTMF. If DTMF Dialing they perform:
is disabled, the panel will always pulse dial. HEX (B) - simulates the [*] key on a touch tone telephone
If the Busy Tone Detection option is enabled, the panel will HEX (C) - simulates the [#] key on a touch tone telephone
hang up after detecting busy tone for 5 seconds and will
HEX (D) - forces the panel to search for dial tone
redial after the amount of time programmed in the Delay
Between Dialing Attempts section. HEX (E) - forces the panel to pause for 2 seconds
Maximum Dialing Attempts determines the maximum num- HEX (F) - marks the end of the telephone number
ber of attempts the panel will make to send a signal to the NOTE:The first digit of all telephone numbers must be the HEX
central station before indicating a Failure to Communicate digit ‘D’ for dial tone search, or HEX digit ‘E’ for a two-second
(FTC) trouble condition. The 3rd Telephone Number can be pause.
used to back up the 1st in this situation. (See 5.7 “Communi-
cator – Telephone Numbers” on page 17.) If a later communi- First Telephone Number. . . . . . . . . . . . . . . . . . . Section [301]
cation attempt is successful, the FTC reporting code(s) Second Telephone Number . . . . . . . . . . . . . . . . Section [302]
programmed in section [351] will be transmitted along with the Third Telephone Number . . . . . . . . . . . . . . . . . . Section [303]
unreported events from an earlier unsuccessful communica- Third Telephone Number Enable . . . . . . . . .Section [380]: [5]
tion. Alternate Dial . . . . . . . . . . . . . . . . . . . . . . . .Section [380]: [6]
Post Dial Wait for Handshake determines the amount of time
the panel will wait for a valid handshake from the receiver. If
the panel does not hear the handshake it will consider the call
a failed attempt, hang up and try again.

17
5.8 Communicator – Reporting Codes access code, if one is programmed for the Key, regardless of
The panel can be programmed to report events to the central this option.
station by sending the Reporting Code programmed for a AC Failure Trouble Alarm Code
particular event. To prevent the panel from transmitting an AC Failure Trouble
Reporting codes can be one or two digits and can use HEX Alarm reporting code during short power outages, the panel
digits (A through F). For a complete description of reporting will not send the signal unless AC power is lost for the amount
codes which can be programmed and lists of automatic Con- of minutes programmed for the AC Failure Communication
tact ID and SIA format codes, please see Appendix A: Delay. The AC Failure Trouble Restoral reporting code follows
“Reporting Codes” on page 42. the AC failure communication delay as well.
NOTE:Do not use the digit C in a reporting code when using NOTE:If AC Failure Communications Delay is programmed as
Pager Format. In most cases, the digit C will be interpreted as “000,” then the AC failure transmission will be immediate.
a [#], which will terminate the page before it has finished.
AC Failure Communication Delay . . . . . . . . . . . Section [370]
Reporting Codes . . . . . . . . . . . . . . . . . Section [320] to [353]
Wireless Maintenance
Cross Zone Police Reporting Code The panel will transmit a Wireless Device Low Battery Alarm
The Cross Zone Police Code Alarm will be sent when two reporting code if a low battery condition is indicated by a
different alarms occur during any armed-to-armed period. detector. The transmission of the trouble will be delayed by
When an alarm occurs while the panel is armed and a second the number of days programmed for Zone Low Battery
alarm occurs on a different zone during the same armed Transmission Delay. The Wireless Device Low Battery Resto-
period, or after the system is disarmed, this code will be sent. ral reporting code will be transmitted when the problem is cor-
All zone types contribute to this alarm. The cross zone police rected. The specific zone that caused the trouble will be
code will be transmitted immediately unless either or both recorded in the event buffer.
zones have the Transmission Delay attribute enabled. If so, NOTE: The restoral will not be transmitted until all detectors
the code will be delayed for the programmed transmission indicate good battery conditions.
delay time.

Cross Zone Police Code Alarm . . . . . . . . . . . . Section [328] Wireless Maintenance Reporting Codes . . . . . Section [353]
Wireless Device Battery Transmission Delay . . Section [370]
Zone Restorals
If the Restoral on Bell Time-out option is selected, the panel Arming and Activity Delinquency
will send the Zone Restoral Reporting Code for the zone if When Delinquency Follows Arming (Days) is selected, the
the bell cut-off time has expired and the zone is secured. If the Delinquency reporting code is sent whenever the panel is not
zone is not secured when the bell cut-off time expires, the armed within the number of days programmed for the Delin-
panel will send the restoral immediately once the zone is quency Transmission Cycle.
secured, or when the system is disarmed. If the Restoral on NOTE: If the Delinquency Transmission Cycle is set for one
Bell Time-out option is not selected, the panel will immediately day, there must be 24 hours of no arming or disarming before
send the Zone Restoral Reporting Code when the zone is the Delinquency Code will be sent. After a Delinquency Code
secured, regardless of whether or not the alarm output is has been transmitted, it will not be sent again until the system
active. has been armed and disarmed.
NOTE:24 Hour type zones will report the restoral immediately When Delinquency Follows Zone Activity (hours) is
when the zone is secured. enabled, if there is no activity on zones in the system, the
Delinquency Transmission Cycle Timer in Section [370] will
Restoral on Bell Time-out . . . . . . . . . . . . . . Section [380]: [2] begin counting in hours. When the counter reaches the pro-
grammed time, the panel will communicate the Delinquency
Closings (Arming Codes) reporting code to the central station, if programmed. If there
If the Closing Confirmation option is enabled, once the exit is a closing or zone activity present on the system at any time,
delay expires, the keypad will sound a series of eight beeps to the counter will be reset.
confirm to the user that the closing code was sent and NOTE:Activity Delinquency will not be reported while the panel
received by the central station. is armed in Away mode.
Closing Confirmation . . . . . . . . . . . . . . . . . . Section [381]: [4] NOTE:Activity on manually bypassed zones will not reset the
timer.
Openings/Closings by Wireless Key NOTE:This timer is reset when the panel is armed, or if
If you are using a PC5132 v3.0 or higher, wireless keys with Installer Programming is entered.
access codes may be identified when they are used to arm or
disarm the system: the panel will log and transmit opening or NOTE:When using the SIA FSK communication format with
closing by access code (the same as if an access code had Activity Delinquency, the Closing Delinquency identifier is
been used to arm/disarm the system). If wireless keys with no transmitted.
access code are used, the event will be logged and transmit-
ted as opening or closing by keyswitch. Miscellaneous Maintenance Reporting Codes. Section [351]
The Function Keys Require Code option must be selected Delinquency Follows Zone Activity . . . . . . . . . . . . . .[380]: [8]
(section [015], option 4 OFF) in order for wireless keys to be Delinquency Transmission Cycle . . . . . . . . . . . . . . . . . . [370]
identified for arming. Disarming will always be logged by

18
 P r o g r a m D e s c r i p t i o n s : 5. 9 C o m m un ic a t or – R e p o rt i ng F or m a t s

5.9 Communicator – Reporting Formats NOTE:If the Automatic Contact ID option is selected, the panel
Each communication telephone number can be programmed will automatically generate all zone and access code numbers,
to report using any one of eight formats available. Two 20 eliminating the need to program these items.
BPS pulse formats are supported, in addition to Contact ID, If the Contact ID uses Programmed Reporting Codes
SIA and Pager formats. option is enabled, the panel will operate as follows:
The Communicator Call Direction options can be used to 1. If an event’s reporting code is programmed as [00] or [FF],
disable the reporting of events such as Openings and Clos- the panel will not attempt to call central station.
ings. 2. If the reporting code for an event is programmed as any-
NOTE: Do not program the 2nd telephone number to use Con- thing from [01] to [FE], the panel will send the programmed
tact ID or SIA reporting code formats (section [360]) if Auto- reporting code.
matic reporting codes are selected for either Contact ID or SIA Additional Notes on Contact ID
(section [381]). 1. Account numbers must be four digits.
2. All reporting codes must be two digits.
Communicator Format Options . . . . . . . . . . . . Section [360] 3. Substitute the HEX digit ‘A’ for the ‘0’.
Communicator Call Directions . . . . . . . Section [361] to [368] 4. To prevent the panel from reporting an event, the reporting
code should be programmed as [00].
The following is a description of each reporting format:
Please refer to Appendix A: “Reporting Codes”for a list of
Pulse Formats Contact ID Identifiers.
Depending on which pulse format is selected, the panel will
communicate using the following specifications: Contact ID Uses Programmed/Automatic Codes . . [381]: [7]
• 3/1, 3/2, 4/1 or 4/2
• 1400 or 2300 Hz handshake SIA
• 20 bits per second SIA is a specialized format that will communicate information
quickly using Frequency Shift Keying (FSK) rather than
• non-extended
pulses. The SIA format will automatically generate the type of
Additional Notes on Pulse Formats
signal being transmitted, such as Burglary, Fire, Panic etc.
1. The digit ‘0’ will send no pulses and is used as a filler digit. The two digit reporting code is used to identify the zone or
2. When programming account numbers, enter four digits. access code number.
When programming a three digit account number, the
NOTE: If the Automatic SIA option is selected, the panel will
fourth digit must be programmed as ‘0’.
automatically generate all zone and access code numbers,
3 digit account number [123] - program [1230]
3. If an account number has a ‘0’ in it, substitute a HEX digit eliminating the need to program these items.
‘A’ for the ‘0’. For example: If the SIA Sends Automatic Reporting Codes option is
3 digit account number [502] - program [5A20] enabled, the panel will operate as follows:
4 digit account number [4079] - program [4A79] 1. If an event’s reporting code is programmed as [00], the
4. Reporting codes are two digits. When programming sin- panel will not attempt to call the central station.
gle-digit Reporting Codes, the second digit must be pro- 2. If the reporting code for an event is programmed as any-
grammed as a ‘0’. If a ‘0’ is to be transmitted, substitute thing from [01] to [FF], the panel will automatically gener-
HEX digit ‘A’. For example: ate the zone or access code number.
1 digit Reporting Code [3] - program [30] If the SIA Sends Programmed Reporting Codes option is
2 digit Reporting Code [30] - program [3A] enabled, the panel will operate as follows:
5. To prevent the panel from reporting an event, the reporting 1. If an event’s reporting code is programmed as [00] or [FF],
code should be programmed as [00] or [FF]. the panel will not attempt to call central station.
Contact ID 2. If the reporting code for an event is programmed as any-
Contact ID is a specialized format that will communicate infor- thing from [01] to [FE], the panel will send the programmed
mation using tones rather than pulses. This format allows more reporting code.
information to be sent faster than other formats. For example, Please refer to Appendix A: “Reporting Codes”for a list of SIA
in addition to reporting an alarm in zone one, the Contact ID identifiers.
format will also report the type of alarm, such as an Entry/Exit
SIA Sends Automatic Reporting Codes. . . .Section [381]: [3]
alarm.
If the Contact ID uses Programmed Reporting Codes Pager Format
option is enabled, a two digit number from Appendix A must The Communicator Format option for either telephone number
be entered in programming sections [320] to [353] for each can be programmed as Pager format. If an event occurs and
event to be transmitted. The two digit number determines the the Communicator Call Direction options direct the call to a
type of alarm. The panel will automatically generate all other telephone number with the Pager Format selected, the panel
information, including the zone number. will attempt to page.
If the Contact ID uses Automatic Reporting Codes option is When calling a pager, extra digits will be required in order for
enabled, the panel will operate as follows: the format to function properly. The following is a list of Hex
1. If an event’s reporting code is programmed as [00], the digits and the functions they perform:
panel will not attempt to call the central station. Hex [B] - simulates the [*] key on a touch tone telephone
2. If the reporting code for an event is programmed as any-
Hex [C] - simulates the [#] key on a touch tone telephone
thing from [01] to [FF], the panel will automatically gener-
ate the zone or access code number. See Appendix A for a Hex [D] - forces the panel to search for dial tone
list of the codes which will be transmitted. Hex [E] - two second pause
Hex [F] - marks the end of the telephone number

19
The panel will attempt to call the pager once. Once the appro- Local Downloading via the PC-LINK, enter [*][8][Installer’s
priate telephone number is dialed, the panel will send the Code][499][Installer’s Code][499]. All keypads will be busy for
account number and Reporting Code followed by the [#] key the duration of the PC-LINK connection. The status LEDs will
(Hex [C]). display the current system status on the keypad where the
The panel has no way of confirming if the pager was called PC-LINK was initiated. For more information on connecting the
successfully. A Failure To Communicate trouble will only be PC-LINK, refer to your “PC-LINK Download Kit Instruction
generated if the panel detects a busy tone on all dialing Sheet”.
attempts, or if no dial tone is detected on all dialing attempts. NOTE: When a zone status upload is performed through PC-
The pager format will not cause any form of ringback. LINK, the information uploaded may not be accurate. For more
NOTE:The Pager Format cannot be used with the LINKS1000 information, refer to your DLS-1 manual.
cellular communicator. Downloading can also be performed through the LINKS1000
NOTE:Do not use the digit C in a reporting code when using cellular communicator if the telephone line is disconnected. If
Pager Format. In most cases, the digit C will be interpreted as using the LINKS1000 with call back, you need to program the
a [#], which will terminate the page before it has finished. LINKS1000 Preamble with the downloading telephone num-
ber in order for the panel to call the computer correctly.
NOTE:If the panel detects a busy signal, it will attempt to page
again. It will make the maximum number of attempts pro- NOTE:When uploading labels from LCD keypads, only labels
from the LCD keypad assigned to slot 8 will be uploaded.
grammed in section [160].
NOTE:Force dialing should be disabled when using Pager for- Answering Machine/Double Call . . . . . . . . Section [401]: [1]
mat. User Enable DLS Window . . . . . . . . . . . . . Section [401]: [2]
NOTE:When using Pager format, you must program two hex Call-Back . . . . . . . . . . . . . . . . . . . . . . . . . . Section [401]: [3]
digit E’s at the end of the telephone number User-initiated Call-up enabled/disabled . . . Section [401]: [4]
Downloading Computer’s Telephone Number . Section [402]
5.10 Downloading Downloading Access Code . . . . . . . . . . . . . . . Section [403]
The required downloading software is DLS-1 v6.7 and up. Panel Identification Code . . . . . . . . . . . . . . . . . Section [404]
Downloading allows you to program the entire control panel Answering Machine Double Call Timer . . . . . . Section [405]
via a computer, a modem and a telephone line. All functions, Number of Rings to Answer On . . . . . . . . . . . . Section [406]
features, their changes and status – such as trouble condi- LINKS1000 Preamble (Downloading) . . . . . . . . Section [490]
tions and open zones – can be viewed or programmed Initiate Local Downloading (PC-LINK) . . . . . . . Section [499]
through downloading.
NOTE:Downloading is always enabled for six hours each time 5.11 PGM Output Options
the panel is powered up, unless the User Can Enable DLS Program the programmable outputs PGM1 and PGM2 on the
Window option is disabled main board by selecting one of the output options listed below
The panel will answer calls for downloading when the pro- (exceptions noted).
grammed Number of Rings is heard by the panel. Main Board PGM Outputs. . . . . . . . . . . . . . . . . Section [009]
If the Answering Machine/Double Call option is enabled (or
during the first six hours after power up), the panel will answer NOTE: PGM outputs cannot be completely disabled in
incoming calls for downloading in the following manner: installer’s programming. To disable a PGM output completely,
1. The panel hears one or two rings then misses a ring. you must remove all wiring from the output.
2. At this point the panel will start a the double-call timer.
[01] Burglary and Fire Bell Output
3. If the panel hears another ring before the Answering
The output will activate when the alarm output is active and
Machine Double-Call Timer expires, it will answer on the
will deactivate when the alarm output is silenced. If the alarm
first ring of the second call.
output is pulsing, the PGM output will pulse as well. This out-
The panel will immediately go on line and begin downloading.
put will follow the activation of the alarm output (pre-alert) for
If the Call-Back option is enabled, the panel and the com-
delayed fire zones.
puter will both hang up. The panel will then call the Down-
loading Computer’s Telephone Number and wait for the [02] For future use
computer to answer. Once the computer answers, download- [03] Sensor Reset ([*][7][2])
ing will begin. NOTE:This output will normally be active (switched to ground).
If the User Enabled DLS Window option is ON, the user can
This option is used to reset power for latching smoke detec-
activate the downloading feature by entering [*][6][Master
tors. The output will deactivate for five seconds when the
Code][5].
[*][7][2] command is entered. (See “[*][7] Command Output
If the User Initiated Call-Up option is enabled, the user can Functions” on page 11.) The keypad buzzer will not sound for
have the panel initiate a call to the downloading computer by the five second period.
pressing [*][6][Master Code][6].
Please refer to the Control Panel Wiring Diagram in this man-
The Download Access Code and Panel Identifier Code are ual for wiring instructions.
for security and proper identification. Both the panel and the
NOTE:Only ONE of options [03] Sensor Reset and [20] [*][7][2]
computer file should contain the same information pro-
grammed before attempting to download.
Command Output Option #2 may be programmed on the same
system.
The time to complete a successful download can be signifi-
cantly reduced with the use of the PC-LINK. This adaptor
makes it possible to perform on-site downloading. To Initiate

20
 P r o g r a m D e s c r i p t i o n s : 5 . 11 P G M O u t pu t O pt i o ns

[04] For future use Program which events will activate the output by selecting
[05] Armed Status some or all of the following attributes:
When the system is armed, the PGM output will activate at the Attribute
beginning of the exit delay. The output deactivates when the [1] .........Burglary (Delay, Instant, Interior, Stay/Away and
system is disarmed. 24 Hour Burglary Zones)
[06] Ready To Arm [2] .........Fire (Fire Keys, Fire Zones)
The PGM will be active as long as the system is ready to arm [3] .........Panic (Panic Keys and Panic Zones)
and all non-force armable zones on the system are restored. [4] .........Medical (Auxiliary Keys, Medical and Emergency
Once an access code is entered to arm the system and the Zones)
exit delay begins, the PGM output is deactivated. [5] .........Supervisory (Supervisory, Freezer and Water
[07] Keypad Buzzer Follower Mode Zones)
The PGM will activate when any of the following events occur [6] .........Priority (Gas, Heat, Sprinkler and 24 Hour Latch-
and will remain active for as long as the keypad buzzer is ing Zones)
active: [7] .........Holdup (Holdup zones)
• Door Chime • Entry Delay [8] .........Output Follows Timer (output will activate for the
• Auto-Arm Prealert • Audible Exit Delay number of seconds programmed in the PGM Out-
• 24 Hour Supervisory Buzzer Zone put Timer) / Output Latched
[08] Courtesy Pulse NOTE:If attribute [8] is turned ON, attributes [1-7] must also be
Upon arming, the PGM output will activate for the duration of turned ON.
the exit delay plus an additional two minutes. Upon disarming,
the PGM output will activate for the duration of the entry delay PGM Output Timer . . . . . . . . . . . . . . . . . . . . . . . Section [164]
plus an additional two minutes.
[11] System Tamper (All Sources)
[09] System Trouble Output The PGM output will activate when any tamper condition is
The PGM output will activate when any of the selected trouble present and will deactivate when all tampers are restored.
conditions are present. It will deactivate when all the selected
trouble conditions are cleared. [12] TLM and Alarm
The PGM output activates when the system experiences both
The PGM attributes for this option, programmed in Sections
a telephone line trouble and an alarm. When the system is
[141] to [142], differ from the standard selection of attributes.
armed, the output will deactivate only if an access code is
Program which trouble conditions will activate the output by
entered or if the telephone line is restored.
selecting some or all of the following attributes:
If an alarm activates this output in the disarmed state, the out-
Attribute put will deactivate if a user enters a valid access code while
[1] .......... Service Required (battery, bell, general trouble, the Bell Cut-off timer is counting down, or if the telephone line
general tamper, general supervisory) is restored. The output will also deactivate if someone arms
[2] .......... AC Failure the system after the Bell Cut-off has expired.
[3] .......... Telephone Line Trouble NOTE:This output will activate for all silent and audible alarms
[4] .......... Failure to Communicate except the Duress alarm.
[5] .......... Fire Trouble / Zone Fault
[13] Kissoff Output
[6] .......... Zone Tamper
The output will activate for two seconds after the control panel
[7] .......... Zone Low Battery
receives the kissoff transmission from the central station.
[8] .......... Loss of Clock
[14] Ground Start Pulse
[10] System Event (Strobe Output) The PGM Output will activate for two seconds to obtain a dial
The output activates when any of the selected system events tone on Ground Start telephone equipment before the panel
(alarms) occur on the system. attempts to dial. Insert two 2-second pauses at the beginning
NOTE:This output will activate for silent and audible alarms or of the telephone number when using this option.
medical conditions only. It will not activate during pre-alert or [15] Remote Operation (DLS-1 Support)
delays. This output can be activated and deactivated remotely using
If attribute [8] is turned ON, the output will activate for the the DLS software.
number of seconds programmed in the PGM output timer [16] LINKS1000 Support (PGM1 Only)
(section [164]). The PGM output will be used as a data wire to communicate
If attribute [8] is turned OFF, in the armed state, the output will telephone number information for the LINKS1000 cellular unit.
deactivate only once the system is disarmed. If an alarm acti-
[17] Away Armed Status
vates this output in the disarmed state, the output will deacti-
When the system is armed in the Away mode, the PGM output
vate if a user enters a valid access code while the Bell Cut-off
will activate at the beginning of the exit delay. The output
timer is counting down. The output will also deactivate if
deactivates when the panel is disarmed.
someone arms the system after the Bell Cut-off has expired.
This output can be used to indicate that an alarm has [18] Stay Armed Status
occurred before entering the premises. When the system is armed in the Stay mode, the PGM output
will activate at the beginning of the exit delay. The output
The PGM attributes for this option, programmed in Sections
deactivates when the panel is disarmed.
[141] to [142], differ from the standard selection of attributes.

21
[19] [*][7][1] Command Output Option #1 5.12 Telephone Line Monitor (TLM)
[20] [*][7][2] Command Output Option #2 When the TLM Enable option is selected, the panel will super-
These outputs are user-initiated by entering [*][7][1-2] at any vise the telephone line and will indicate a trouble condition if
keypad. When any output is activated, three acknowledgment the telephone line is disconnected.
beeps are sounded. If the TLM Enable option is ON, the panel will check the tele-
NOTES on Option [20] [*][7][2]: phone line every 10 seconds. If the telephone line voltage is
Press [*][7][2][Access Code, if required] to activate any out- below 3V for the number of checks programmed in the TLM
put programmed as one of PGM output option [03] or [20]. Trouble Delay section, the panel will report a TLM trouble.
Traditionally, [*][7][2] has been reserved for resetting smoke The default number of checks is 3. Enter a number from [003]
detectors. Smoke detectors should now be programmed as to [255] in the TLM Trouble Delay section to change the num-
output [03] “Sensor Reset”. ber of checks before the TLM trouble is reported. Program-
ming a delay means that a momentary interruption of the
NOTE:Only ONE of options [03] Sensor Reset and [20] [*][7][2] telephone line will not cause a trouble condition.
Command Output Option #2 may be programmed on the same
If the TLM Trouble Beeps When Armed option is enabled,
system.
the panel will indicate a TLM trouble at the keypad while the
[21]-[24] For future use system is armed. To activate the bell output in the case of a
PGM Output Attributes TLM trouble while the system is armed, the TLM Audible
In addition to programming the output type, you must also (Bell) When Armed option must be selected.
program the PGM output attributes for each output. When the trouble condition is restored, the panel can send a
PGM output options [09] “System Trouble” and [10] “System TLM Restoral reporting code. Any events which occur while
Event” have their own unique set of attributes listed below the the telephone line is down will also be communicated.
description of each output type. If the LINKS1000 Cellular Communicator, Skyroute transceiver,
PGM output options [01], [03], [05]-[08], [11]-[20] have the or LINKS2X50 is being used, the panel can be programmed to
following attributes: report a TLM Trouble Reporting Code.
Attribute.... ON OFF TLM Enable/Disable . . . . . . . . . . . . . . . . . . Section [015]: [7]
[1] ....... PGM Enable PGM Disable TLM Trouble Beeps When Armed or
[3] ....... True Output Inverted Output TLM Audible (Bell) When Armed . . . . . . . . Section [015]: [8]
Attribute ON: the output energizes when activated TLM Trouble Reporting Code . . . . . . . . . . . . . . Section [349]
Attribute OFF: the output de-energizes when acti- TLM Restoral Reporting Code . . . . . . . . . . . . . Section [350]
vated TLM Trouble Delay . . . . . . . . . . . . . . . . . . . . . . Section [370]
[4] ....... Output Pulsed Output ON/OFF
Attribute ON: the output will activate once for the
5.13 Bell
amount of time programmed in section [164]
The bell will silence after the number of minutes programmed
when initiated by the user
for the Bell Cut-off time have passed.
Attribute OFF: the output will toggle ON or OFF
when initiated by the user. The panel supervises the Bell output. If an open condition is
(Only applicable to options [19]-[20].) detected, the panel will immediately indicate a trouble condi-
tion by beeping the keypad twice every 10 seconds to alert
[5] ....... Access Code Req. No code Req.
the owner of the problem. The panel can send a Bell Circuit
Attribute ON: the output requires a code for acti-
Trouble and Trouble Restoral reporting codes to indicate the
vation.
situation (See 5.8 “Communicator – Reporting Codes” on
Attribute OFF: no code required.
page 18.)
(only applicable to keypad-activated outputs)
If the Temporal Three Fire Signal option is enabled, all Fire
PGM attributes return to their default settings when you
signals (on zone types [07], [08], [87], [88]) will follow the
change PGM output options. Please see the programming
Temporal Three Pattern as described in NFPA 72. If turned
worksheets for a list of the default settings for each PGM out-
OFF all Fire signals will sound a one second on, one second
put type.
off cadence.
Be careful when selecting the normal and active states of
If Fire Bell Continuous is enabled, the alarm output will
each PGM output to ensure that an undesirable output state
sound until a code is entered. If disabled, the alarm will sound
does not occur after a loss and restore of AC power.
until a code is entered or the bell cut-off time has expired.
NOTE: Attribute [3] must be ON (default) for PGM output
option [16]. Bell Cut-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [005]
NOTE: If you program more than one PGM output as the same Bell Circuit Trouble Reporting Code . . . . . . . . . Section [349]
output type (e.g. if PGM1 and PGM2 are both programmed as Bell Circuit Trouble Restoral Reporting Code . . Section [350]
[19] Command Output 1), the settings for output attributes [1], Temporal Three Fire Signal Enable/Disable Section [013]: [8]
[2] and [5] must be the same. This does not apply to outputs Fire Bell Continuous . . . . . . . . . . . . . . . . . . Section [014]: [8]
programmed as types [09] and [10].
5.14 Test Transmission
PGM Output Attributes . . . . . . . . . . . . . . Section [141]-[142] To ensure that the communication link with the central station
is functioning properly, program the panel to send a test trans-
mission signal on a regular basis.

22
 P r o g r a m D e s c r i p t i o n s : 5 . 1 5 T r a n sm i ss io n D e l a y

The panel can send a Periodic Test Transmission Reporting NOTE:The Fire, Auxiliary, Panic keys will operate even if Key-
Code at the programmed Test Transmission Time of Day. pad Blanking is active (See 5.22 “Keypad Blanking” on page
The Test Transmission Cycle determines the period of time 24.)
between tests.
NOTE:The LINKS Test Transmission can only be programmed [F] Key Enable . . . . . . . . . . . . . . . . . . . . . . .Section [015]: [1]
in days. [P] Key Audible Bell and Buzzer . . . . . . . . .Section [015]: [2]
If you program the test transmission cycle for a longer period
of time than it was programmed for previously, the system will 5.17 Arming/Disarming Options
wait the original time period before the next test transmission If the Quick Arm option is enabled, the panel can be armed
is sent, and then begin reporting with the new interval. without an access code by entering [*][0] or by pressing the
The panel can also send a test for the LINKS1000 Cellular Stay or Away function key. If the Quick Arm option is disabled,
Communicator, if used. If the LINKS1000 Test Transmission users will need to enter an access code after pressing a func-
Code is programmed, the panel will send a cellular test at the tion key.
interval programmed in the LINKS Test Transmission Cycle. The Quick Exit option, if enabled, will allow someone to leave
Users can also generate a communicator test. If the System an armed premises through a Delay type zone without having
Test Reporting Code is programmed, the panel will send the to disarm and re-arm the system. See “[*][0] Quick Exit” on
signal when the System Test keypad command is entered. page 11.
(See “[*][6] User Functions” on page 10.) Enable the Arm/Disarm Bell Squawk option to have the
panel squawk the alarm output once upon arming and twice
Test Transmission Reporting Codes. . . . . . . . . Section [352] upon disarming. If an alarm is in memory, when the panel is
Test Transmission Time of Day . . . . . . . . . . . . . Section [371] disarmed the bell will sound three pairs of disarm squawks.
Test Transmission Cycles . . . . . . . . . . . . . . . . . Section [370]
NOTE: If you enable the Bell Squawk on Arming/Disarming
(section [014], option [1]), the bell will sound arm/disarm bell
5.15 Transmission Delay squawks for all access codes, regardless of the programming
If the transmission delay zone attribute is selected for a given for attribute [7]. See “[*][5] Programming Access Codes” on
zone, the panel will delay reporting an alarm for that zone for page 10.
the number of seconds programmed for the Transmission Enable both the Squawk on Away Arming/Disarming Only
Delay Time. If the panel is disarmed before the delay time and the Arm/Disarm Bell Squawk options to have the panel
expires, the panel will not report the event. squawk the bell only when the system is away armed or dis-
Transmission Delay Time . . . . . . . . . . . . . . . . . Section [370] armed.
The Opening After Alarm Keypad Ringback option will
cause the keypad to beep 8 times rapidly after the Opening
5.16 Fire, Auxiliary and Panic Keys After Alarm reporting code has been successfully transmitted
The emergency keys are available on all keypads. These keys to the central station. The Opening After Alarm Bell Ring-
must be pressed and held for two seconds before they will back option will cause the panel to squawk the bell 8 times
activate. This two second delay is designed to help prevent rapidly after the Opening After Alarm reporting code has been
accidental activation. successfully transmitted to the central station.
If the [F] / Key option is enabled, when the Fire keys are NOTE:If the panel is armed using the Stay function key, or by
pressed and held for two seconds, the panel will activate the entering [*][9][access code], there will be no bell squawks dur-
alarm output following the option programmed in section ing entry and exit delays, except for the arm/disarm bell
[013]: [8] (see section 5.13 “Bell” on page 22). The alarm out- squawks.
put will sound until a code is entered or until the bell cut-off
Closing Confirmation, if enabled, will cause the keypad to
time expires. Communication of the signal to central station is
beep 8 times rapidly after the closing reporting code has
immediate.
been successfully transmitted to central station.
If the [A] / Key is pressed and held for two seconds, the If the Bypass Status Displayed While Armed option is cho-
panel will sound the keypad beeps three times to verify acti- sen, the Bypass light will be ON while the system is armed to
vation. The panel will beep the keypad ten times rapidly when indicate that there are bypassed zones.
a kissoff is received, to verify communication to the central
If you enable the WLS Key Does Not Use Access Codes
station.
option, the disarm button will work on wireless keys which
If the [P] / Key is pressed and held for two seconds, the have not been assigned access codes. Wireless keys can
panel will immediately communicate the signal to central sta- only be assigned access codes when used with PC5132 v3.0
tion. or higher.
If [P] Key Audible Bell and Buzzer option is enabled, when a To prevent disarming by wireless keys which don’t have
user presses the [P] / key, the keypad will beep three times access codes, disable this option. (Please see your PC5132
and the panel will activate the alarm output until an access manual for more information on programming wireless keys.)
code is entered or the bell cut-off expires. If the option is dis- NOTE: This option must be enabled when using a PC5132
abled, the Panic alarm will be completely silent. v2.1 or earlier.
Each LCD keypad may be programmed to have the [F], [A], &
[P] keys enabled or disabled. Please refer to Appendix B: Quick Arm Enable . . . . . . . . . . . . . . . . . . . .Section [015]: [4]
“Programming LCD Keypads” on page 44. Quick Exit Enable. . . . . . . . . . . . . . . . . . . . .Section [015]: [3]
Arm/Disarm Bell Squawk . . . . . . . . . . . . . . .Section [014]: [1]

23
Squawk on Away Arm/Disarm Only. . . . . . . Section [017]: [8] Bell Squawk Options. . . . . . . . . . . . . . Section [014]: [2] - [4]
Closing Confirmation . . . . . . . . . . . . . . . . . . Section [381]: [4] Exit Delay Termination. . . . . . . . . . . . . . . . . Section [014]: [7]
Opening After Alarm Keypad Ringback . . . Section [381]: [1]
Opening After Alarm Bell Ringback . . . . . . Section [381]: [2]
5.19 Swinger Shutdown
Bypass Status Displayed While Armed. . . . Section [016]: [7]
The swinger shutdown feature is designed to prevent a “run-
Unident. Wkey Disarm Enabled . . . . . . . . . Section [017]: [1]
away” communicator from tying up the central station. After
the panel has communicated the programmed number of
5.18 Entry/Exit Delay Options transmissions for an event, it will no longer report that event
Two different Entry Delays can be programmed: the first entry until the swinger shutdown is reset. Different swinger shut-
delay will be enabled for Delay 1 type zones and the second down levels can be set for zone alarms, zone tampers and
for Delay 2 type zones. Only one Exit Delay can be pro- maintenance signals.
grammed. By default, each Swinger Shutdown limit is set to [003]. The
NOTE:When the panel is armed, the entry delay will follow the panel will not send more than three signals for each zone until
entry delay time programmed for the delay zone which is vio- the swinger shutdown is reset.
lated first. The Bell output will not be activated for alarms on zones that
have exceeded the limit of alarms set in the Swinger Shut-
Users can restart the exit delay by pressing the Away key
down counter.
while it is counting down. The system will not log the user who
re-started the exit delay, unless the Quick Arming Disabled/ Swinger shutdown will be reset every day at midnight or when
Function Keys Require Code option is turned on (section the panel is armed. Once reset, the panel will again communi-
[015], option [4]). cate normally.
NOTE: If the system has been Stay armed or armed with no Swinger Shutdown . . . . . . . . . . . . . . . . . . . . . . Section [370]
entry delay ([*][9]) pressing the Away key will not start an exit
delay.
5.20 Event Buffer
Upon arming, the panel will begin the exit delay. If the Audible The panel will store the last 128 events which occurred on the
Exit Delay with Urgency option is enabled, the keypad will system. The Event Buffer will contain the name, time and
beep at one second intervals until the exit delay expires. The date of each event, along with the zone number, access code
keypad will beep rapidly for the last 10 seconds of exit delay number or any other information pertaining to the event.
to warn the user that the system is about to arm. If this option If the Event Buffer Follows Swinger Shutdown option is
is disabled, the keypad will not beep during the exit delay. enabled, the event buffer will not store events after the
The Audible Exit Fault, as explained in Section 3.1, will notify Swinger Shutdown level has been reached. This will prevent
the user if they failed to secure the premises upon arming. the panel from overwriting the entire buffer if a problem exists.
This option can be enabled or disabled according to the The event buffer can be viewed in three different ways: from
user’s needs. an LCD keypad (see “[*][6] User Functions” on page 10)
For commercial applications, the Bell Squawk on Exit Delay printed on-site using the PC5400 printer module, or it can be
option may be enabled. The panel will squawk the alarm out- uploaded using DLS software.
put once every second when the exit delay is initiated and
three times per second for the last 10 seconds until the exit Event Buffer Follows
delay expires. Swinger Shutdown . . . . . . . . . . . . . . . . . . . Section [013]: [7]
Upon entry, if a Delay type zone is violated, the panel will
begin the entry delay. The keypad will emit a steady tone. The 5.21 Keypad Lockout Options
keypad will pulse the keypad sounder during the last 10 sec-
The panel can be programmed to “lock out” keypads if a
onds to warn the user the system is about to go into alarm. If
series of incorrect access codes are entered. Once the Num-
there was an alarm during the armed period, the keypad will
ber of Invalid Codes Before Lockout limit has been reached,
pulse for the entire entry delay to warn the user of the previous
the panel will lock out all keypads for the Lockout Duration
alarm.
and log the event to the event buffer. For the duration of the
For commercial applications Bell Squawk on Entry Delay lockout, the panel will sound an error tone when any key is
may be enabled. The panel will squawk the alarm output once pressed.
every second until the entry delay expires or the system is dis-
NOTE: The Invalid Code Counter will be reset every hour.
armed.
If the Bell Squawk During Auto Arm option is enabled, the To disable the keypad lockout option, program the Number of
bell will squawk once every 10 seconds for one minute during Invalid Codes Before Lockout as [000].
the Auto-arm pre-alert. This will notify anyone on the premises NOTE: If Keypad Lockout is active, the panel CANNOT be
that the system is being armed. armed / disarmed with a keyswitch.
If the Exit Delay Termination option is enabled, the panel will
monitor the Delay 1 zones during exit delay. During the exit Keypad Lockout Options . . . . . . . . . . . . . . . . . Section [012]
delay, if a Delay 1 type zone is violated and then secured, the
exit delay will be terminated and the panel will be armed 5.22 Keypad Blanking
immediately.
If the Blank Keypad When Not in Use option is enabled, the
Entry Delay 1 and 2 (System Times) . . . . . . . . . Section [005] panel will turn off all lights and LCDs on the keypads when no
Exit Delay (System Times). . . . . . . . . . . . . . . . . Section [005] keys are pressed for 30 seconds. The keys, however, will
Audible Exit Delay with Urgency . . . . . . . . . Section [014]: [6] remain backlit.
Audible Exit Fault Enabled/ Disabled . . . . . Section [013]: [6]

24
 P r o g r a m D e s c r i p t i o n s : 5 . 2 3 K e y p a d B ac k li gh t in g

The panel will turn the lights and LCDs back on if entry delay NOTE: If a LINKS1000 is connected to the system, make sure
begins or an audible alarm occurs. The lights and LCDs will the Maximum Number of Dialing Attempts is programmed to
also come on if a key is pressed or, if a valid access code is be 008 or greater (section [160].
entered when the Code Required to Restore Blanking
Using LINKS1000 as the Sole Communicator
option is enabled.
The panel can be programmed to report an event only using
NOTE:If using a PC5132 v3.0 or greater, and wireless keys, do the LINKS1000 cellular communicator. To program this option,
not enable the Code Required to Restore Blanking option, as select only the LINKS1000 in the Communicator Call Direction
the keys will not function correctly. Options. The Call LINKS as well as Land Line option must also
If the Power Save Mode option is enabled the panel will blank be enabled.
all keypad lights including backlighting when AC power fails, When the selected event occurs the panel will only attempt to
in order to conserve the back up battery. call central station using the LINKS.
Using the LINKS1000 as a Backup Communicator
Blank Keypad when not in use. . . . . . . . . . Section [016]: [3]
The panel can be programmed to call using the LINKS1000
Code Required to Restore Blanking. . . . . . Section [016]: [4]
Cellular Communicator if the panel is having difficulty commu-
Power Save Mode . . . . . . . . . . . . . . . . . . . Section [016]: [6]
nicating an event using the land line. To program this option,
select both the telephone number and LINKS options in the
5.23 Keypad Backlighting Communicator Call Direction Options. The LINKS is Backup
The keys of all the keypads can be backlit to provide easy of Land Lines option must be selected.
viewing in dim lighting conditions. If the Keypad Backlighting When used as a backup communicator, the panel will attempt
option is enabled the keys will be illuminated. to call the central station in the following manner:
the panel will try to call using land lines – if unsuccessful, the
Keypad Backlighting Option . . . . . . . . . . . Section [016]: [5]
panel will try to call using the LINKS
if unsuccessful, the panel will try to call using the land lines on
5.24 Loop Response the next dialing attempt
The normal loop response time for all zones is 500 millisec- This process will continue until the panel has successfully
onds. The panel will not consider a zone violated unless it is communicated with the central station or until the panel’s pro-
violated for at least 500 milliseconds. grammed number of dialing attempts have been exhausted.
Zones 1-4 on the control board, however, can be programmed
Using the LINKS as a Redundant Communicator
for a fast loop response (under 40ms).
The panel can be programmed to call using first the
Zones 1-4 are Fast Loop Response . . . . . Section [030]: [1-4] LINKS1000 and then the land line when an event occurs. To
program this option, select both the telephone number and
the LINKS options for the Communicator Call Direction
5.25 Keypad Tampers Options for the event. The Call LINKS as well as Land Line
If the Keypad Tampers Enable option is selected, the panel option must be selected.
will display and transmit a General System Tamper reporting
LINKS Special Preamble
code if any keypad is removed from the wall. When the key-
In some areas of North America, dialing #DAT or *DATA
pad tamper is restored, the panel will transmit the General
reduces the cellular billing increment. The LINKS Special
System Tamper Restoral reporting code. All keypads should
Preamble (section [393]), allows the use of [*] and [#] charac-
be properly installed and secured before enabling this option.
ters for the programming of #DAT and *DATA.
NOTE:The auto arm cancellation code is not transmitted when
The LINKS Special Preamble is sent BEFORE the Preamble
a reset is required because a user has not cancelled the auto-
programmed in Sections [390] to [392].
arming sequence.
Example: [Special Preamble][Regular Preamble][Telephone
Number]
Keypad Tamper Enable . . . . . . . . . . . . . . . Section [016]: [8]
General System Tamper and Tamper NOTE: If this Special Preamble is programmed, it will be
Restoral Reporting Codes . . . . . . . . . . . . . . . . Section [338] inserted before the Regular Preamble of ALL telephone num-
bers. Hex digits D and E are not supported for Preamble pro-
NOTE: After enabling keypad tampers, it is recommended to gramming.
tamper and restore all keypads to ensure proper functioning. NOTE: If Busy Tone Detection is enabled, the LINKS1000
must be tested to ensure full operation.
5.26 LINKS1000 Cellular Communicator*
The LINKS1000 Cellular Communicator can be used three dif- Please refer to the LINKS1000 installation Manual for more
ferent ways: information and connection diagrams.
• as the sole communicator for the panel
LINKS Preamble (First Telephone Number). . . . Section [390]
• as a backup for either or both telephone numbers LINKS Preamble (Second Telephone Number) . Section [391]
• as a redundant backup to the land line communicator, LINKS Preamble (Third Telephone Number) . . . Section [392]
where the panel will call using the land line and the LINKS. LINKS Preamble
A LINKS Preamble is programmable for each telephone num- (Downloading Telephone Number) . . . . . . . . . . Section [490]
ber in the event that the land line number is local but the Communicator Call Direction Options . . . Section [361]-[368]
LINKS is required to dial an exchange. When programming a Call LINKS as well as Land Line . . . . . . . . .Section [380]: [7]
LINKS Preamble, all unused digits must be programmed with LINKS Special Preamble . . . . . . . . . . . . . . . . . . Section [393]
a hexadecimal “F”.
*Not investigated by UL

25
5.27 Additional System Modules* 5.29 Installer’s Lockout
The following modules are programmed through the module If Installer’s Lockout is selected, a hardware default cannot
programming sections [801]-[804]: the PC5400 Printer mod- be performed. If a software default is performed, all program-
ule, the Links2X50 Long-Range Radio module, the Skyroute ming will restore to factory default.
transceiver module, and the PC5132 Wireless Receiver and If Installer’s Lockout Disable is selected, the panel will
all of its devices. For instructions on the installation and pro- restore all programming to factory defaults when a hardware
gramming of these additional modules and devices, please or software default is performed on the main control panel.
see their respective installation and programming manuals. To enable or disable Installer’s Lockout, perform the following:
1. Enter the Installer’s Programming mode.
PC5400 Printer Module Programming. . . . . . . . Section [801]
2. Enter the appropriate programming section: [990] or [991].
Alternative Comm. (LINKS2X50, Skyroute)
3. Enter the Installer’s Code.
Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . Section [803]
4. Re-enter the appropriate programming section: [990] or
PC5132 Programming . . . . . . . . . . . . . . . . . . . . Section [804]
[991].

5.28 Resetting Factory Defaults* Installer Lockout Enable . . . . . . . . . . . . . . . . . . Section [990]

On occasion, it may be necessary to default the main control Installer Lockout Disable . . . . . . . . . . . . . . . . . Section [991]
panel or one of the connected modules: the LINKS2X50 Radio
interface, Skyroute module, the PC5132 wireless receiver, and 5.30 Walk Test (Installer)
the PC5400 Printer module. The Installer Walk Test can be used to test the alarm state of
To default the main control panel (hardware), perform the fol- each zone of the panel. The walk test cannot be used to test
lowing: zone type [24].
1. Remove AC and battery from the panel. Before beginning the walk test, ensure the following condi-
2. Remove all wires from the Zone 1 and PGM1 terminals. tions are met:
3. With a piece of wire short the Zone 1 terminal to the PGM1 1. The panel is disarmed
terminal. 2. The Keypad Blanking option is disabled (section [016]:
4. Apply AC power to the main panel. [3])
5. When Zone Light 1 is lit on the keypad the default is com- 3. The Fire Bell is Continuous option is disabled (section
plete. [014]: [8])
6. Remove AC power from the control 4. The Transmission Delay is disabled, if Transmission
7. Reconnect all original wiring and power up the control. Delay is not required (section [370])
NOTE: AC power must be used to power the panel. The panel NOTE: Fire Troubles are not supported in Walk Test.
will not default if only the battery is used.
To perform a walk test:
To default the main control panel software and other modules, Step 1 - Enter Installer Programming
perform the following: Step 2 - Enter Section [901]
1. Enter the Installer’s Programming mode. When any zone is violated the panel will activate the Bell Out-
2. Enter the appropriate programming section [XXX]. put for two seconds, log the event to the event buffer and
3. Enter the Installer’s Code. communicate the alarm to central station.
4. Re-enter the appropriate programming section [XXX]. Test each zone several times. Check the event buffer to
The panel will take a few seconds to perform the default. ensure that all zones and FAP keys are functioning properly.
When the keypad is again operational the default is complete.
NOTE: Zones with the Force Arm attribute enabled, will not
NOTE:If using Identified Wireless Keys (PC5132 v3.0 or later cause the Ready light to go out when they are violated.
only), when the main panel is defaulted, all wireless key
access codes must be re-programmed. Refer to your PC5132 To stop the test:
v3.0 Installation Manual for more information. Step 1 - Enter Installer Programming
Step 2 - Enter section [901]
Restore Alternative Communicator NOTE:The alarm memory is cleared upon entering Walk Test
(LINKS2X50, Skyroute) mode. When the walk test is complete, the Alarm Memory light
to Default Programming. . . . . . . . . . . . . . . . . . . Section [993] will remain lit, but there will be no alarms in memory. The light
Restore PC5132 to Default Programming . . . . . Section [996] will turn off the next time the panel is armed.
Restore PC5400 Printer to Default ProgrammingSection [997]
Restore Panel to Default Programming . . . . . . . Section [999] Installer Walk Test Enable/Disable . . . . . . . . . . Section [901]

26 *LINKS1000, LINKS2X50, and Skyroute have not been investigated by UL.

 S e ction 6 : Programmi ng Work s he et s
For the Record

Customer: _______________________________________________________________________________________________________

Address: ________________________________________________________________________________________________________

Telephone: ___________________________________________ Installation Date: ___________________________________________

Installer’s Code: __________________________________________________________________________________________________

Module Name Description Location

PC580 Main Panel I________________________________________________________________________________________________________________I

PC5132 Wireless Receiver I________________________________________________________________________________________________________________I

PC5400 Serial Printer Module I________________________________________________________________________________________________________________I

LINKS1000 Cellular Communicator I________________________________________________________________________________________________________________I

LINKS2X50 Long Range Radio I________________________________________________________________________________________________________________I

Skyroute Transceiver I________________________________________________________________________________________________________________I

Keypads Keypad Type Location

Keypad 1 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 2 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 3 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 4 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 5 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 6 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 7 I_____________________________________________I I________________________________________________________________________________________________________________I

Keypad 8 I_____________________________________________I I________________________________________________________________________________________________________________I

*LINKS1000, LINKS2X50, and Skyroute have not been investigated by UL. 27

Zone Programming Summary
Zone programming can be found in sections [001] - [004], [101] - [132], [020] and [202] - [205]. Use this area to record a sum-
mary of your zone programming. Refer to Appendix B: “Programming LCD Keypads” on page 44, for instructions on programming
zone labels.
System Zone Label Zone Zone Attributes* Serial Number
Zone Type 1 2 3 4 5 6 7 8 (Wireless)
Zone 1 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 2 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 3 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 4 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 5 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 6 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 7 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 8 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 9 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 10 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 11 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 12 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 13 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 14 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 15 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 16 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 17 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 18 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 19 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 20 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 21 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 22 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 23 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 24 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 25 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 26 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 27 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 28 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 29 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 30 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 31 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

Zone 32 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I_____I_____I_____I_____I_____I

*Zone Attributes:
Option 1: Audible/Silent Option 5: Force**
Option 2: Steady/Pulsed Option 6: Swinger Shutdown
Option 3: Chime Option 7: Transmission Delay
Option 4: Bypass Option 8: Wireless
**NOTE: Option 5, Force Arming is not recommended for UL installations.

28
 P r o g r a m m i n g W o r k s h e e t s

Keypad Programming
[000] Keypad Enrollment (Section 2.5 “Keypad Assignment” on page 4)
NOTE: This must be done at each keypad requiring programming.
[0] Slot [Valid entries are 11-18; i.e. enter [11] for slot 1, [12] for slot 2, etc.]
[1] Function Key 1 Assignment (Valid entries are 00-17)
[2] Function Key 2 Assignment (Valid entries are 00-17)
[3] Function Key 3 Assignment (Valid entries are 00-17)
[4] Function Key 4 Assignment (Valid entries are 00-17)
[5] Function Key 5 Assignment (Valid entries are 00-17)
Function Key Options:
00 Null Key 08 [*][1] Bypass Mode 16 [*][0] Quick Exit
01 For future use 09 [*][2] Trouble Display 17 [*][1] Reactivate Stay/Away’s
02 For future use 10 [*][3] Alarm Memory 18 For future use
03 Stay Arm 11 [*][5] User Programming 19 For future use
04 Away Arm 12 [*][6] User Functions 20 For future use
05 [*][9] No-Entry Arm 13 Command Output #1 [*][7][1] 21 For future use
06 [*][4] Chime On / Off 14 Command Output #2 [*][7][2]
07 [*][6][——][4] System Test 15 For future use
Slot Function Function Function Function Function
Key 1 Key 2 Key 3 Key 4 Key 5
LED Defaults 11 03 04 06 14 16
LCD Defaults 18 03 04 06 14 16
KEYPAD 1 I________I________I I________I I________I I________I I________I I________I

KEYPAD 2 I________I________I I________I I________I I________I I________I I________I

KEYPAD 3 I________I________I I________I I________I I________I I________I I________I

KEYPAD 4 I________I________I I________I I________I I________I I________I I________I

KEYPAD 5 I________I________I I________I I________I I________I I________I I________I

KEYPAD 6 I________I________I I________I I________I I________I I________I I________I

KEYPAD 7 I________I________I I________I I________I I________I I________I I________I

KEYPAD 8 I________I________I I________I I________I I________I I________I I________I

Basic Programming
Zone Definitions
00 Null Zone (Not Used) 10 24 Hour Supervisory Buzzer 20 24 Hour Freeze
01 Delay 1 11 24 Hour Burglary 21 24 Hour Latching Tamper
02 Delay 2 12 24 Hour Holdup 22 Momentary Keyswitch Arm
03 Instant 13 24 Hour Gas 23 Maintained Keyswitch Arm
04 Interior 14 24 Hour Heating (N/C zone) 24 LINKS Answer
05 Interior, Stay/Away 15 24 Hour Medical 25 Interior Delay
06 Delay, Stay/Away 16 24 Hour Panic 87 Delay 24 Hour Fire (Wireless)
07 Delayed 24 Hour Fire (Hardwired) 17 24 Hour Emergency 88 Standard 24 Hour Fire (Wireless)
08 Standard 24 Hour Fire (Hardwired) 18 24 Hour Sprinkler
09 24 Hour Supervisory 19 24 Hour Water
NOTE:Keypads must be installed to use 24-hour Buzzer zones.
NOTE:Keypad zones are assigned in section [020]. Zone Attributes are assigned in sections [101] - [132]. Zone assignment is in
sections [202] - [205].
[001] Zone 1-8 Definitions (Section 5.2 “Zone Programming” on page 15)
Default Default
01 I_______I_______I Zone 1 00 I_______I_______I Zone 5
03 I_______I_______I Zone 2 00 I_______I_______I Zone 6
04 I_______I_______I Zone 3 00 I_______I_______I Zone 7
04 I_______I_______I Zone 4 00 I_______I_______I Zone 8

29
NOTE:Zones 9-32 are only available for wireless zones.
[002] Zone 9-16 Definitions (Section 5.2 “Zone Programming” on page 15)
Default Default
00 I_______I_______I Zone 9 00 I_______I_______I Zone 13
00 I_______I_______I Zone 10 00 I_______I_______I Zone 14
00 I_______I_______I Zone 11 00 I_______I_______I Zone 15
00 I_______I_______I Zone 12 00 I_______I_______I Zone 16
[003] Zone 17-24 Definitions (Section 5.2 “Zone Programming” on page 15)
Default Default
00 I_______I_______I Zone 17 00 I_______I_______I Zone 21
00 I_______I_______I Zone 18 00 I_______I_______I Zone 22
00 I_______I_______I Zone 19 00 I_______I_______I Zone 23
00 I_______I_______I Zone 20 00 I_______I_______I Zone 24
[004] Zone 25-32 Definitions (Section 5.2 “Zone Programming” on page 15)
Default Default
00 I_______I_______I Zone 25 00 I_______I_______I Zone 29
00 I_______I_______I Zone 26 00 I_______I_______I Zone 30
00 I_______I_______I Zone 27 00 I_______I_______I Zone 31
00 I_______I_______I Zone28 00 I_______I_______I Zone 32
[005] System Times
Default Valid entries: [001-255]
030 I_______I_______I_______I Entry Delay 1 (in seconds)(Section 5.18 “Entry/Exit Delay Options” on page 24)
045 I_______I_______I_______I Entry Delay 2 (in seconds)(Section 5.18 “Entry/Exit Delay Options” on page 24)
120 I_______I_______I_______I Exit Delay (in seconds)(Section 5.18 “Entry/Exit Delay Options” on page 24)
004 I_______I_______I_______I Bell Cut-off (in minutes)(Section 5.13 “Bell” on page 22)
[006] Installer’s Code (Section 4.1 “Installer’s Programming” on page 13)
Default
5555 I_______I_______I_______I_______I

[007] Master Code (Section 5.1 “Programming Security Codes” on page 15)
Default
1234 I_______I_______I_______I_______I

[008] Maintenance Code (Section 5.1 “Programming Security Codes” on page 15)
Default
AAAA I_______I_______I_______I_______I

[009] PGM Output Programming (PGM 1 and 2) (Section 5.11 “PGM Output Options” on page 20)
Programmable Output Options
01 Burglary and Fire Bell Output 14 Ground Start Pulse
02 For future use 15 Remote Operation (DLS-1 Support)
03 Sensor Reset 16 LINKS1000 Support (PGM1 only)
04 For future use 17 Away Armed Status
05 System Armed Status 18 Stay Armed Status
06 Ready To Arm 19 Command Output #1 ([*][7][1])
07 Keypad Buzzer Follow Mode 20 Command Output #2 ([*][7][2])
08 Courtesy Pulse 21 For future use
09 System Trouble Output (with Trouble options) 22 For future use
10 System Event [Strobe (with Event options)] 23 For future use
11 System Tamper (all sources: zones, kpd, modules) 24 For future use
12 TLM and Alarm
13 Kissoff Output
NOTE:Output types [03] and [20] cannot be used together on the same system.
Default Default
19 I_______I_______I PGM 1 10 I_______I_______I PGM 2 Program PGM Option Attributes in sections [141] & [142].

30
 P r o g r a m m i n g W o r k s h e e t s

[012] Keypad Lockout Options (Section 5.21 “Keypad Lockout Options” on page 24)
NOTE:If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
Default
000 I_______I_______I_______I Number of Invalid Codes Before Lockout (001-255 codes)
000 I_______I_______I_______I Lockout Duration (001-255 minutes)
[013] First System Option Code
Default Option ON Off Section Page #
OFF I________I 1 Normally Closed Loops End-of-Line Resistors 2.8 5
OFF I________I 2 Double End-of-Line Resistors Single End-of-Line Resistors 2.8 5
ON* I________I 3 Panel shows all troubles when armed Panel shows only Fire troubles when armed 3.4 8
OFF I________I 4 Tampers/Faults do not show as open Tampers/Faults show as open 3.4 8
OFF I________I 5 For future use
ON I________I 6 Audible Exit Fault Enabled Audible Exit Fault Disabled 5.18 24
ON I________I 7 Event Buffer Follows Swinger Shutdown Event Buffer Logs Events Past shutdown 5.20 24
OFF I________I 8 Temporal Three Fire Signal Enabled** Standard Pulsed Fire Signal 5.13 22
* Option 3 must be OFF if LCD keypads older than v2.0 are used.
**The Temporal Three Fire Signal option must be used for UL Household Fire installations.
[014] Second System Option Code
Default Option ON Off Section Page #
OFF I________I 1 Arm / Disarm Bell Squawk enabled Arm / Disarm Bell Squawk disabled 5.17 23
OFF I________I 2 Bell Squawk During Auto Arm No Bell Squawk During Auto Arm 5.18 24
OFF I________I 3 Bell Squawk On Exit Delay No Bell Squawk On Exit Delay 5.18 24
OFF I________I 4 Bell Squawk On Entry Delay No Bell Squawk On Entry Delay 5.18 24
OFF I________I 5 Bell Squawk On Trouble No Bell Squawk On Trouble 3.4 8
ON I________I 6 Audible Exit with Urgency Silent Exit Delay 5.18 24
OFF I________I 7 Exit Delay Termination Enabled Exit Delay Termination Disabled 5.18 24
OFF I________I 8 Fire Bell is Continuous Fire Bell Follows Bell Cut-off 5.13 22
[015] Third System Option Code
Default Option ON Off Section Page #
ON I________I 1 Fire Keys Enabled Fire Keys Disabled 5.16 23
OFF I________I 2 Panic Keys Audible (Bell / Beeps) Panic Keys Silent 5.16 23
OFF I________I 3 Quick Exit Enabled Quick Exit Disabled 3.4 8
ON* I________I 4 Quick Arming Enabled Quick Arming Dis. / Function keys Req. Code 3.4 8
OFF I________I 5 Code Required For Bypassing No Code Required 3.4 8
OFF I________I 6 Master Code Not Changeable Master Code Changeable 5.1 15
ON I________I 7 TLM Enabled TLM Disabled 5.12 22
OFF I________I 8 TLM Audible (Bell) When Armed TLM Trouble Beeps When Armed 5.12 22
* When using a PC5132 version 2.1 or older with WLS909 Wireless Keys, option [4] must be ON for the Arm button to work.
[016] Fourth System Option Code
Default Option ON Off Section Page #
ON I________I 1 AC Trouble Displayed AC Trouble Not Displayed 3.4 8
OFF I________I 2 Trouble Light Flashes if AC Fails Trouble Light Does Not Follow AC Status 3.4 8
OFF I________I 3 Blank Keypad When Not Used Keypad Active Always 5.22 24
OFF I________I 4 Code Required to Remove Kypd BlankingNo Code Required 5.22 24
ON I________I 5 Keypad Backlighting is enabled Keypad Backlighting is disabled 5.23 25
OFF I________I 6 Power Save Mode enabled Power Save Mode disabled 5.22 24
OFF I________I 7 Bypass Status Displayed While Armed Bypass Status Not Displayed While Armed 5.17 23
OFF I________I 8 Keypad Tampers enabled Keypad Tampers disabled 5.25 25

31
[017] Fifth System Option Code
Default Option ON Off Section Page #
ON I________I 1 WLS Key Does Not Use Access Codes* WLS Key Uses Access Codes 5.17 23
OFF I________I 2-7 For future use
OFF I________I 8 Squawk on Away Arming/Disarming OnlyBell Squawk on all Arming/Disarming 5.17 23
*This option must be enabled when using a PC5132 v2.1 or earlier.

[020] Keypad Zone Assignments (Section 2.11 “Keypad Zones” on page 6)

NOTE:Only one keypad may be assigned to a zone.
Default
00 I________I_______I Keypad (slot 1) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 2) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 3) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 4) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 5) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 6) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 7) Zone Valid entries are zones 01-08
00 I________I_______I Keypad (slot 8) Zone Valid entries are zones 01-08

[030] Zone Loop Response Options

Default Option ON Off Section Page #
OFF I________I 1 Zone 1 is Fast Loop Response Zone 1 is Normal Loop Response 5.24 25
OFF I________I 2 Zone 2 is Fast Loop Response Zone 2 is Normal Loop Response 5.24 25
OFF I________I 3 Zone 3 is Fast Loop Response Zone 3 is Normal Loop Response 5.24 25
OFF I________I 4 Zone 4 is Fast Loop Response Zone 4 is Normal Loop Response 5.24 25
OFF I________I 5-8 For future use

32
 P r o g r a m m i n g W o r k s h e e t s

Advanced System Programming

Zone Attributes (Section 5.3 “Zone Attributes” on page 16)
Zone Attribute Defaults (Y = Option ON; N = Option OFF):
Attribute: 1 2 3 4 5 6 7 8
ON Audible Steady Chime Bypass Force* Swing Tx. Delay Wireless Zn.
OFF Silent Pulsed No No No No No No
Zone Type:
00 Null Zone N N N N N N N N
01 Delay 1 Y Y Y Y N Y N N
02 Delay 2 Y Y Y Y N Y N N
03 Instant Y Y Y Y N Y N N
04 Interior Y Y N Y N Y N N
05 Int. Stay/Away Y Y N Y Y Y N N
06 Dly. Stay/Away Y Y N Y Y Y N N
07 Dly. 24hr Fire (Hardw.) Y N N N N N N N
08 Stand. 24hr Fire (Hardw.) Y N N N N N N N
09 24hr Superv. N Y N N Y N N N
10 24hr Superv. Buzzer N Y N Y N N N N
11 24hr Burglary Y Y N Y N N N N
12 24hr Holdup N Y N N N N N N
13 24hr Gas Y N N N N N N N
14 24hr Heating (N/C zone) Y N N N N N N N
15 24hr Medical Y Y N N N N N N
16 24hr Panic Y Y N N N N N N
17 24hr Emergency Y Y N N N N N N
18 24hr Sprinkler Y Y N N N N N N
19 24hr Water Y Y N N N N N N
20 24hr Freeze Y Y N N N N N N
21 24hr Latching Tamper Y Y N N N N N N
22 Momentary Keyswitch N N N N Y N N N
23 Maintained Keyswitch N N N N Y N N N
24 LINKS Answer N N N N Y N N N
25 Interior Delay Y Y N Y N Y N N
87 Dly. 24hr Fire (Wireless) Y N N N N N N Y
88 Stand. 24hr Fire (Wireless) Y N N N N N N Y
*NOTE: For UL installations, do not change attribute 5 (Force Arming) from the default setting.
Section Zone # Zone 1 2 3 4 5 6 7 8
Type*
[101] 1 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[102] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[103] 3 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[104] 4 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[105] 5 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[106] 6 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[107] 7 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[108] 8 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[109] 9 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[110] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[111] 11 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[112] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[113] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[114] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

33
[115] 15 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[116] 16 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[118] 18 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[119] 19 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[120] 20 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[121] 21 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[122] 22 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[123] 23 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[124] 24 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[125] 25 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[126] 26 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[127] 27 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[128] 28 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[129] 29 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[130] 30 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[131] 31 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[132] 32 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

*Record here based on programming in sections [001] - [004]

PGM Output Attributes (Section 5.11 “PGM Output Options” on page 20)
Program only the following attributes for the PGM options listed. All others will be ignored. PGM options are programmed in [009].
PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF):
Attribute: 1 2 3 4 5
ON Output enabled — True Output Follows Timer Code Req.

OFF Output disabled — Inverted On / Off No Code Req.

PGM Option
[01] Burg. / Fire Bell Y Y
[03] Sensor Reset Y Y N
[05] Armed Status Y Y
[06] Ready To Arm Y Y
[07] Kypd Bzz Follow Y Y
[08] Courtesy Pulse Y Y
[11] System Tamper Y
[12] TLM and Alarm Y
[13] Kiss-off Y
[14] Gnd Strt Pulse Y
[15] Remote Op. Y
[16] LINKS1000 Sup. Y
[17] Away Armed Status Y Y
[18] Stay Armed Status Y Y
[19] Comm. Output #1 Y Y Y Y
[20] Comm. Output #2 Y Y Y N

Attribute: 1 2 3 4 5 6 7 8
PGM Option
ON Serv. req. AC Fail TLM Fault FTC Zone Fault Zone Tmp. Zn. Low Bat. Loss of Clock
OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled
[09] System Trouble Y Y Y Y Y Y Y Y
ON Burg. Evnt. Fire Evnt. Panic Evnt. Med. Evnt. Supv. Evnt. Priority Evnt. Holdup Evnt. Follows Timer*
OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Latched
[10] System Event Y Y Y Y Y Y Y N
*If attribute [8] is turned ON, attributes [1-7] must also be turned ON.

34
 P r o g r a m m i n g W o r k s h e e t s

Section PGM Output 1 2 3 4 5 6 7 8

# Type*
[141] 1 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[142] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

*Record here based on programming in [009].

[160] Maximum Dialing Attempts to Each Telephone Number (Section 5.5 “Communicator – Dialing” on page 17)
Default: 008 I_______I_______I_______I Valid entries are 001-015 attempts (do not enter 000).
[161] Post Dial Wait for Handshake (All Formats) (Section 5.5 “Communicator – Dialing” on page 17)
Default: 040 I_______I_______I_______I Valid entries are 001-255 seconds
[164] PGM Output Timer (Section 5.5 “Communicator – Dialing” on page 17)
Default: 005 I_______I_______I_______I Valid entries are 001-255 seconds

[202] Zone Assignments 01-08 (Section 5.2 “Zone Programming” on page 15)
Program zone definitions in sections [001] - [004] and zone attributes in sections [101] - [132]. Program keypad zone assignments
in section [020].
NOTE:Any zones not used on the system should be disabled in this section. Disabled wireless zones should have a blank serial
number (i.e. [000000]).
Zones 1-8: Default = ON; Zones 9-32: Default = OFF
Section Option: 1 2 3 4 5 6 7 8
[202] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I

[203] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I

[204] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I

[205] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I

Communicator Programming
NOTE: For sections [301] to [353], the content of every section by default is [F].
[301] First Telephone Number (32 Digits) (Section 5.7 “Communicator – Telephone Numbers” on page 17)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[302] Second Telephone Number (32 Digits) (Section 5.7 “Communicator – Telephone Numbers” on page 17)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[303] Third Telephone Number (32 Digits) (Section 5.7 “Communicator – Telephone Numbers” on page 17)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[310] First/Third Telephone Number Account Code (Section 5.6 “Communicator – Account Numbers” on page 17)
I_______I_______I_______I_______I

[311] Second Telephone Number Account Code (Section 5.6 “Communicator – Account Numbers” on page 17)
I_______I_______I_______I_______I

Alarm Reporting Codes, Zones 1-32 (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
Section
[320] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[321] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[322] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[323] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

35
Alarm Restoral Reporting Codes, Zones 1-32 (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
Section
[324] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[325] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[326] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[327] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[328] Miscellaneous Alarm Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Duress Alarm I_______I_______I 4. Zone Expander Supervisory Alarm
I_______I_______I 2. Opening After Alarm I_______I_______I 5. Zone Expander Supervisory Restoral
I_______I_______I 3. Recent Closing I_______I_______I 6. Cross Zone Police Code Alarm
[329] Priority Alarm and Restoral (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Keypad Fire Alarm I_______I_______I 5. Keypad Fire Restoral
I_______I_______I 2. Keypad Auxiliary Alarm I_______I_______I 6. Keypad Auxiliary Restoral
I_______I_______I 3. Keypad Panic Alarm I_______I_______I 7. Keypad Panic Restoral
I_______I_______I 4. For future use I_______I_______I 8. For future use
Tamper Reporting Codes, Zones 1-32 (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
Section
[330] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[331] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[332] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[333] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Tamper Restoral Reporting Codes, Zones 1-8 (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
Section
[334] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[335] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[336] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[337] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[338] Miscellaneous Tamper Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. General System Tamper

I_______I_______I 2. General System Tamper Rest.

I_______I_______I 3. Keypad Lockout

36
 P r o g r a m m i n g W o r k s h e e t s

Closing (Arming) Reporting Codes, Access Codes 1-32 (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
Section
[339] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[340] Code 9 Code 10 Code 11 Code 12 Code 13 Code 14 Code 15 Code 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[341] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[342] Code 25 Code 26 Code 27 Code 28 Code 29 Code 30 Code 31 Code 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[343] Miscellaneous Closing (Arming) Reporting Codes

(Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Closing by Duress Code 33 I_______I_______I 5. Closing by Supervisory Code 42
I_______I_______I 2. Closing by Duress Code 34 I_______I_______I 6. Partial Closing
I_______I_______I 3. Closing by Master Code 40 I_______I_______I 7. Special Closing
I_______I_______I 4. Closing by Supervisory Code 41
Opening (Disarming) Reporting Codes, Access Codes 1-8 (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
Section
[344] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[345] Code 9 Code 10 Code 11 Code 12 Code 13 Code 14 Code 15 Code 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[346] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[347] Code 25 Code 26 Code 27 Code 28 Code 29 Code 30 Code 31 Code 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[348] Miscellaneous Opening (Disarming) Reporting Codes

(Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Opening by Duress Code 33 I_______I_______I 5. Opening by Supervisory Code 42
I_______I_______I 2. Opening by Duress Code 34 I_______I_______I 6. Auto Arm Cancellation
I_______I_______I 3. Opening by Master Code 40 I_______I_______I 7. Special Opening
I_______I_______I 4. Opening by Supervisory Code 41
[349] Maintenance Alarm Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Battery Trouble Alarm I_______I_______I 5. Auxiliary Power Supply Trouble Alarm
I_______I_______I 2. AC Failure Trouble Alarm I_______I_______I 6. TLM Trouble Code (via LINKS)
I_______I_______I 3. Bell Circuit Trouble Alarm I_______I_______I 7. For future use
I_______I_______I 4. Fire Trouble Alarm I_______I_______I 8. General System Supervisory
[350] Maintenance Restoral Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Battery Trouble Restoral I_______I_______I 5. Auxiliary Power Supply Trouble Restoral
I_______I_______I 2. AC Failure Trouble Restoral I_______I_______I 6. TLM Restoral
I_______I_______I 3. Bell Circuit Trouble Restoral I_______I_______I 7. For future use
I_______I_______I 4. Fire Trouble Restoral I_______I_______I 8. General System Supervisory Restore
[351] Miscellaneous Maintenance Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Telephone Number 1 FTC Restore I_______I_______I 5. DLS Lead OUT
I_______I_______I 2. Telephone Number 2 FTC Restore I_______I_______I 6. Zone Fault Alarm
I_______I_______I 3. Event Buffer 75% Full Since Last Upload I_______I_______I 7. Zone Fault Restore
I_______I_______I 4. DLS Lead IN I_______I_______I 8. Delinquency Code
[352] Test Transmission Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Periodic Test Transmission I_______I_______I 3. LINKS1000 Test Transmission Code*
2. System Test
I_______I_______I

*The LINKS Test Transmission Code must be programmed as “00” for the LINKS Test Transmission to be disabled.

37
[353] Wireless Maintenance Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 18, & Appendix A)
I_______I_______I 1. Wireless Device Low Battery Alarm I_______I_______I 2. Wireless Device Low Battery Restore
[360] Communicator Format Options (Section 5.9 “Communicator – Reporting Formats” on page 19)
NOTE:The Third telephone number follows the format of the First telephone number.
Default
02 I_______I_______I 1st/3rd Telephone Number
02 I_______I_______I 2nd Telephone Number
01 20 BPS, 1400 HZ handshake 04 SIA FSK
02 20 BPS, 2300 HZ handshake 05 Pager
03 DTMF CONTACT ID
[361] Alarm/Restore Communicator Call Directions (Section 5.5 “Communicator – Dialing” on page 17)
Default Option ON OFF
ON I_______I 1 1st Telephone Number Disabled
OFF I_______I 2 2nd Telephone Number Disabled
OFF I_______I 3 1st Telephone Number (via LINKS) Disabled
OFF I_______I 4 2nd Telephone Number (via LINKS) Disabled
OFF I_______I 5-8 For future use
[363] Tamper/Restore Communicator Call Directions (Section 5.5 “Communicator – Dialing” on page 17)
Default Option ON OFF
ON I________I 1 1st Telephone Number Disabled
OFF I________I 2 2nd Telephone Number Disabled
OFF I________I 3 1st Telephone Number (via LINKS) Disabled
OFF I________I 4 2nd Telephone Number (via LINKS) Disabled
OFF I________I 5-8 For future use
[365] Opening/Closing Communicator Call Directions (Section 5.5 “Communicator – Dialing” on page 17)
Default Option ON OFF
ON I________I 1 1st Telephone Number Disabled
OFF I________I 2 2nd Telephone Number Disabled
OFF I________I 3 1st Telephone Number (via LINKS) Disabled
OFF I________I 4 2nd Telephone Number (via LINKS) Disabled
OFF I________I 5-8 For future use
[367] System Maintenance Alarm/Restore Communicator Call Directions (Section 5.5 “Communicator – Dialing” on page 17)
Default Option ON OFF
ON I________I 1 1st Telephone Number Disabled
OFF I________I 2 2nd Telephone Number Disabled
OFF I________I 3 1st Telephone Number (via LINKS) Disabled
OFF I________I 4 2nd Telephone Number (via LINKS) Disabled
OFF I________I 5-8 For future use
[368] System Test Transmissions Communicator Call Directions (Section 5.5 “Communicator – Dialing” on page 17)
Default Option ON OFF
ON I________I 1 1st Telephone Number Disabled
OFF I________I 2 2nd Telephone Number Disabled
OFF I________I 3 1st Telephone Number (via LINKS) Disabled
OFF I________I 4 2nd Telephone Number (via LINKS) Disabled
OFF I________I 5-8 For future use
NOTE:The LINKS1000 backup call directions will only back up their respective telephone numbers.

38
 P r o g r a m m i n g W o r k s h e e t s

[370] Communication Variables

Default Section Page #
003 I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 5.19 24
003 I_______I_______I_______I Swinger Shutdown (Tampers and Rest)(001-014 Transmissions, 000=disabled) 5.19 24
003 I_______I_______I_______I Swinger Shutdown (Maint and Rest) (001-014 Transmissions, 000=disabled) 5.19 24
000 I_______I_______I_______I Transmission Delay (001-255 seconds) 5.15 23
030 I_______I_______I_______I AC Failure Communication Delay (001-255 minutes) 5.8 18
003 I_______I_______I_______I TLM Trouble Delay (No. of checks required - valid entries 003 - 255) 5.12 22
030 I_______I_______I_______I Test Transmission Cycle (land line) (001-255 days) 5.14 22
030 I_______I_______I_______I Test Transmission Cycle (LINKS) (001-255 days) 5.14 22
007 I_______I_______I_______I Zone Low Battery Transmission Delay (000-255 days) 5.8 18
030 I_______I_______I_______I Delinquency Transmission Cycle (000-255 days/hours) 5.8 18
NOTE: To disable the AC failure communications delay, program [000].
[371] Test Transmission Time of Day (Section 5.14 “Test Transmission” on page 22)
Default
9999 I_______I_______I_______I_______I (Valid entries are 0000-2359, 9999 to disable)
[380] First Communicator Option Code
Default Option ON OFF Section Page #
ON I_______I 1 Communications Enabled Communications Disabled 5.5 17
OFF I_______I 2 Restorals on Bell Time-out Restorals Follow Zones 5.8 18
OFF I_______I 3 Pulse Dialing DTMF Dialing 5.5 17
ON I_______I 4 Switch to Pulse Dialing on 5th Attempt DTMF Dial For All Attempts 5.5 17
OFF I_______I 5 3rd Telephone Number enabled 3rd Telephone Number disabled 5.7 17
OFF I_______I 6 Alternate Dial (1st and 3rd) Call 1st Number, Backup to 3rd 5.7 17
OFF I_______I 7 Call LINKS as well as Land Line LINKS is Backup of Land Line(s) 5.26 25
OFF I_______I 8 Delinquency Follows Zone Activity (Hours) Delinquency Follows Arming (Days) 5.8 18
[381] Second Communicator Option Code
Default Option ON OFF Section Page #
OFF I_______I 1 Open After Alarm Kypd Ringback enabled Open After Alrm Kypd Ringback disabled 5.17 23
OFF I_______I 2 Open After Alarm Bell Ringback enabled Open After Alrm Bell Ringback disabled 5.17 23
OFF I_______I 3 SIA Sends Programmed Rep. Codes SIA Sends Automatic Rep. Codes 5.9 19
OFF I_______I 4 Closing Confirmation Enabled Closing Confirmation Disabled 5.17 23
OFF I_______I 5-6 For future use —
ON I_______I 7 Contact ID Uses Programmed Rep. Codes Contact ID Uses Automatic Rep. Codes 5.9 19
OFF I_______I 8 For future use —
[390] LINKS Preamble (First Telephone Number) (Section 5.26 “LINKS1000 Cellular Communicator*” on page 25)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[391] LINKS Preamble (Second Telephone Number) (Section 5.26 “LINKS1000 Cellular Communicator*” on page 25)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[392] LINKS Preamble (Third Telephone Number) (Section 5.26 “LINKS1000 Cellular Communicator*” on page 25)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[393] LINKS Special Function Preamble (All Telephone Numbers) (Section 5.26 “LINKS1000 Cellular Communicator*” on
page 25)
Default: FFFFFF I_______I_______I_______I_______I_______I_______I (Program all unused digits with Hex F)
•Enter [*][2][*] (HEX B) to dial [*] • Enter [*][3][*] (HEX C) to dial [#]

39
Downloading Options
[401] First Downloading Option Code (Section 5.10 “Downloading” on page 20)
Default Option ON Off
OFF I_______I 1 Answering machine/double call enabledAnswering machine/double call disabled
ON I_______I 2 User Can Enable DLS Window User Cannot Enable DLS Window
OFF I_______I 3 Call-Back Enabled Call-Back Disabled
OFF I_______I 4 User-initiated call-up enabled User-initiated call-up disabled
OFF I_______I 5-8 For future use
[402] Downloading Computer’s Telephone Number (32 Digits) (Section 5.10 “Downloading” on page 20)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[403] Downloading Access Code (Section 5.10 “Downloading” on page 20)

Default: 0580 I_______I_______I_______I_______I Enter 4 HEX digits
[404] Panel Identification Code (Section 5.10 “Downloading” on page 20)
Default: 0580 I_______I_______I_______I_______I Enter 4 HEX digits
[405] Answering Machine Double-call Timer (Section 5.10 “Downloading” on page 20)
Default: 060 I_______I_______I_______I (Valid entries are 001-255 seconds)
[406] Number of Rings to Answer On (Section 5.10 “Downloading” on page 20)
Default: 000 I_______I_______I_______I (Valid entries are 000-255 rings)
[490] LINKS Preamble (Downloading Telephone Number) (Section 5.10 “Downloading” on page 20)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[499] [Installer’s Code] [499] Initiate PC-Link (Local Downloading) (Section 5.10 “Downloading” on page 20)

International Programming
[701] First International Options Code
Default Option ON Off Section Page #
OFF I_______I 1-4 For Future Use
OFF I_______I 5 6-Digit User Access Codes 4-Digit User Access Codes 5.1 15
OFF I_______I 6 Busy tone detection enabled Busy tone detection disabled 5.5 17
OFF I_______I 7-8 For Future Use

Module Programming*
[801] PC5400 Printer Module Programming
Please refer to your PC5400 Installation Manual for installation and programming instructions.
[803] Alternative Communicator Programming
Please refer to your LINKS2X50, Skyroute Installation Manual for installation and programming instructions.
[804] PC5132 Wireless Expansion Programming
Please refer to your PC5132 Installation Manual for programming locations and instructions.
* LINKS2X50 and Skyroute modules have not been investigated by UL.

40
 P r o g r a m m i n g W o r k s h e e t s

Special Installer Functions

[901] Installer Walk Test Mode Enable / Disable (Section 5.30 “Walk Test (Installer)” on page 26)
[902] Module Supervision Reset (Section 2.7 “Removing Modules” on page 5)
[903] Module Supervision Field (Section 2.6 “Supervision” on page 5)
[904] Wireless Module Placement Test
For more information, please refer to your PC5132 Installation Manual
• Select the module / transmitter (Zones 01-32).
• Press [#] to Cancel.
Placement Led Keypad LCD Keypad Bell / Buzzer
Good Light 1 ON Steady “GOOD” 1 Beep / Squawk
Fair Light 2 ON Steady “FAIR” 2 Beeps / Squawks
Bad Light 3 ON Steady “BAD” 3 Beeps / Squawks
[990] Installer Lockout Enable (Section 5.29 “Installer’s Lockout” on page 26)
[991] Installer Lockout Disable (Section 5.29 “Installer’s Lockout” on page 26)
[993] Restore Alternative Communicator to Factory Default Programming
(Section 5.28 “Resetting Factory Defaults*” on page 26)

[996] Restore PC5132 to Factory Default Programming (Section 5.28 “Resetting Factory Defaults*” on page 26)
[997] Restore PC5400 to Factory Default Programming (Section 5.28 “Resetting Factory Defaults*” on page 26)
[999] Restore PC580 to Factory Default Programming (Section 5.28 “Resetting Factory Defaults*” on page 26)

41
 A p p e n d ix A: R e p o rti ng Co d e s
The following tables contain Contact ID and Automatic SIA for- SIA Format - Level 2 (Hardcoded)
mat reporting codes. For more information on reporting code The SIA communication format used in this product follows the
formats and notes about individual reporting codes, see sec- level 2 specifications of the SIA Digital Communication Stan-
tions 5.8 “Communicator – Reporting Codes” on page 18 and dard - January 1996. This format will send the Account Code
5.9 “Communicator – Reporting Formats” on page 19. along with its data transmission. The transmission would look
Contact ID similar to the following at the receiver:
The first digit (in parentheses) will automatically be sent by the N Ri01 BA 01
control. The second two digits are programmed to indicate spe- N = New Event
cific information about the signal. Ri01 = Partition /Area Identifier
For example, if zone 1 is an entry/exit point, you could program BA = Burglary Alarm
the event code as [34]. The central station would receive the 01 = Zone 1
following:
*BURG - ENTRY/EXIT - 1
where the “1” indicates which zone went into alarm.

Dialer Contact SIA Auto Rep

Section # Reporting Code Code Sent When...
Direction* ID Codes Codes**
[320] Zone Alarms zone goes into alarm A/R (1) 3A See Table 3
[324] Zone Restorals alarm condition has been restored A/R (1) 3A
[330] Zone Tamper/Restoral zone exhibits a tamper condition/tamper condition T/R (1) 44 TA-ZZ/TR-ZZ
[334] restored
[328] Duress Alarm duress code entered at keypad A/R (1) 21 HA-00
[328] Opening After Alarm system disarmed with alarm in memory A/R (4) A6 OR-00
[328] Recent Closing alarm occurs within two minutes of system arming A/R (4) 59 CR-00
[328] Zone Expander Supervisory panel loses/restores supervisory transmission over the A/R (1) 43 UA-00/UH-00
Alarm/Rest. Keybus from enrolled PC5132 module or keypads with
zone inputs
[328] Cross Zone (Police Code) two zones on the same partition go into alarm during A/R (1) 4A BV-00
Alarm any given armed-to-armed period (incl. 24Hr zones)
[329] [F] Key Alarm/Rest. Keypad fire alarm (alarm and restore rep. codes sent A/R (1) 15 FA-00/FH-00
together)
[329] [A] Key Alarm/Rest. Keypad auxiliary alarm (alarm and restore rep. codes A/R (1) AA MA-00/MH-00
sent together)
[329] [P] Key Alarm/Rest. Keypad panic alarm (alarm and restore rep. codes sent A/R (1) 2A PA-00/PH-00
together)
[338] General System Tamper/ enrolled module with tamper inputs has a tamper alarm/ T/R (1) 45 TA-00/TR-00
Rest. all module tampers restored
[338] Keypad Lockout max. number of incorrect access codes has been T/R (4) 21 JA-00
entered at a keypad
[339-343] Closings system armed (user 01-34, 40-42 indicated) O/C (4) A2 CL-UU
[343] Partial Closing one or more zones bypassed when system armed O/C (4) 7A CG-ZZ
[343] Special Closing Closing (arming) using one of the following methods: O/C (4) AA CL-00
quick arm, auto arm, keyswitch, function key, mainte-
nance code, DLS software
[344-348] Openings system disarmed (user 01-34, 40-42 indicated) O/C (4) A2 OP-UU
[348] Auto Arm Cancellation auto arm cancelled O/C (4) A5 CE-00
[348] Special Opening Opening (disarming) using one of the following meth- O/C (4) AA OP-00
ods: keyswitch, maintenance code, DLS software
[349-350] Battery Trouble/Rest. PC580 battery is low/battery restored MA/R (3) A2 YT-00/YR-00
* A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions
** UU = user number (user01-42); ZZ = zone number (01-08)

42
 R e p o r t i n g C o d e s

Dialer Contact SIA Auto Rep

Section # Reporting Code Code Sent When...
Direction* ID Codes Codes**
[349-350] AC Line Trouble/Rest. AC power to control panel is disconnected or inter- MA/R (3) A1 AT-00/AR-00
rupted/AC power restored (Both codes follow AC Fail-
ure Comm. Delay.)
[349-350] Main Bell Trouble/Rest. open circuit detected across bell terminals/bell circuit MA/R (3) 21 UT-99/UJ-99
closed
[349-350] Fire Trouble/Rest. a trouble occurs/restores on a fire zone MA/R (3) 73 FT-00/FJ-00
[349-350] Auxiliary Power Trouble/ aux voltage supply trouble/restoral MA/R (3) AA YP-00/YQ-00
Rest.
[349] TLM Failure telephone line monitoring trouble (sent via LINKS. Do MA/R (3) 51 LT-00
not program if LINKS not used)
[350] TLM Restore Telephone line trouble restore MA/R (3) 51 LR-00
[349-350] Gen System Supervisory control panel loses/restores communications with mod- MA/R (3) 33 ET-00/ER-00
Trouble/Rest. ule(s) connected to the Keybus
[351] Line 1 or 2 FTC Restoral control panel has restored communications to central MA/R (3) 54 YK-00
station on line 1 or 2 (after FTC)
[351] Event Buffer is 75% Full event buffer is almost full since last upload MA/R (6) 23 JL-00
[351] DLS Lead In downloading session start MA/R (4) 11 RB-00
[351] DLS Lead Out downloading session complete MA/R (4) 12 RS-00
[351] Zone Fault/Rest. one or more zones have faults/restored MA/R (3) 72 UT-00/UJ-00
[351] Delinquency programmed amount of time (days or hours) for delin- MA/R (4) 54*** CD-00
quency has expired without zone activity or without sys-
tem being armed
[352] Periodic Test periodic system test transmission T (6) A2 RP-00
[352] System Test [*][6] bell/communications test T (6) A1 RX-00
[352] LINKS Test LINKS test transmission T (6) A3 TX-00
[353] Wireless Device Low Battery wireless zones (WLS904, WLS905, WLS907); panic MA/R (3) 84 XT-00/XR-00
Trouble/Rest. pendants (WLS908); handheld keypads (WLS910);
wireless keys (WLS909) have low battery/all low batter-
ies restored
* A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions
** UU = user number (user01-42); ZZ = zone number (01-08)
***Program the “Fail to close” event code [(4)54] to report either closing or activity delinquency. Make sure your central station is aware of the application of this
reporting code.

Table2: Contact ID Zone Alarm/Restoral Event Table 3: SIA Format Automatic Zone
Codes (as per ADEMCO): Alarm/Restoral Codes
Program any of these codes for zone alarms/restorals when using
the standard (non-automatic) Contact ID reporting format. SIA Auto Rep
Zone Definition Codes*
Medical Alarms (1)34 Entry / Exit
(1)AA Medical (1)35 Day / Night Zone Alm/Rest.
(1)A1 Pendant Transmitter (1)36 Outdoor Delay, Instant, Interior, Delay BA-ZZ/BH-ZZ
(1)A2 Fail to Report In (1)37 Tamper Stay/Away, Interior Stay/Away,
Fire Alarms (1)38 Near Alarm 24Hr Burg.
(1)1A Fire Alarm General Alarms Standard 24Hr Fire, Delayed FA-ZZ/FH-ZZ
(1)11 Smoke (1)4A General Alarm 24Hr Fire
(1)12 Combustion (1)43 Exp. module failure 24Hr Supervisory US-ZZ/UR-ZZ
(1)13 Water Flow (1)44 Sensor tamper
(1)14 Heat (1)45 Module Tamper 24Hr Supervisory Buzzer UA-ZZ/UH-ZZ
(1)15 Pull Station (1)4A Cross Zone Police Code 24Hr Sprinkler SA-ZZ/SH-ZZ
(1)16 Duct 24 Hour Non-Burglary 24Hr Gas GA-ZZ/GH-ZZ
(1)17 Flame (1)5A 24 Hour non-Burg
24Hr Heat KA-ZZ/KH-ZZ
(1)18 Near Alarm (1)51 Gas detected
Panic Alarms (1)52 Refrigeration 24Hr Medical MA-ZZ/MH-ZZ
(1)2A Panic (1)53 Loss of Heat 24Hr Emergency (non-medical) QA-ZZ/QH-ZZ
(1)21 Duress (1)54 Water Leakage
24Hr Waterflow WA-ZZ/WH-ZZ
(1)22 Silent (1)55 Foil Break
(1)23 Audible (1)56 Day Trouble 24Hr Freeze ZA-ZZ/ZH-ZZ
Burglar Alarms (1)57 Low bottled Gas level 24Hr Holdup HA-ZZ/HH-ZZ
(1)3A Burglary (1)58 High Temp 24Hr Panic PA-ZZ/PH-ZZ
(1)31 Perimeter (1)59 Low Temp
(1)32 Interior (1)61 Loss of Air Flow Latching 24Hr BA-ZZ/BH-ZZ
(1)33 24 Hour * ZZ = zones 01-08

43
 Appendix B: Programming LCD Keypads
If you have an LCD5500Z Keypad, additional programming is required for proper operation. The following is a description of the
available programming options and their accompanying programming sections:
How to Enter LCD Programming
Follow the programming procedure as outlined in Section 4 by pressing [*][8][Installer’s Code]. Press the [*] key. Enter the two
digit Section number to be programmed.
Programmable Labels – Sections [01] - [08], [33], [34], [40], [44], [51], [52]
Zone labels and other LCD display identifiers can be customized to make operation of the system easier for the end user. The fol-
lowing procedure should be used for creating all LCD labels:
• Enter Installer’s Programming. Enter the Number corresponding to the label to be programmed.
• Use the arrow keys (<>) to move the underline bar underneath the letter to be changed.
• Press the number key [1] to [9] corresponding to the letter you require. The first time you press the number the first letter will
appear. Pressing the number key again will display the next letter. Refer to the following chart:
[1] - A, B, C, 1 [2] - D, E, F, 2 [3] - G, H, I, 3 [4] - J, K, L, 4 [5] - M, N, O, 5
[6] - P, Q, R, 6 [7] - S, T, U, 7 [8] - V, W, X, 8 [9] - Y, Z, 9,0 [0] - Space
• When the required letter or number is displayed use the arrow keys (<>) to scroll to the next letter.
• When you are finished programming the Zone Label, press the [*] key, scroll to “Save,” then press [*].
• Continue from Step 2 until all Labels are programmed.
[01] to [32] Zone Labels (14 Characters)
Default: “Zone 1” - “Zone 32”
Record zone labels on page 28
[33] Fire Alarm Label (14 Characters)
Default: “Fire Zone” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[34] System Label (14 Characters)

Default: “System” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[40] to [44] [*][7][1-2] Command Output Option Labels (14 Characters)

[40] Default: “Command O/P 1”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[44] Default: “Command O/P 2”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[51] Fail to Arm Event Message
Default: “System Has Failed to Arm” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[52] Alarm When Armed Event Message
Default: “Alarm Occurred While Armed < >”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[60] First User Display Mask
Default Option ON OFF
ON I_______I 1 Hold [P]anic Keys prompt ON Hold [P]anic Keys prompt OFF
ON I_______I 2 Zone Bypassing prompt ON Zone Bypass prompt OFF
ON I_______I 3 Troubles prompt ON Troubles prompt OFF
ON I_______I 4 Alarm Memory prompt ON Alarm Memory prompt OFF
ON I_______I 5 Door Chime Control prompt ON Door Chime Control prompt OFF
ON I_______I 6 Access Codes prompt ON Access Codes prompt OFF
ON I_______I 7 User Functions prompt ON User Functions prompt OFF
ON I_______I 8 Output Control prompt ON Output Control prompt OFF

44
 P r o g r a m m i n g L C D K e y p a d s

[61] Second User Display Mask

Default Option ON OFF
OFF I_______I 1 Installer Programming prompt ON Installer Programming prompt OFF
ON I_______I 2 Stay Arm prompt ON Stay Arm prompt OFF
ON I_______I 3 Quick Arm prompt ON Quick Arm prompt OFF
ON I_______I 4 Interior Arm prompt ON Interior Arm prompt OFF
OFF I_______I 5 Quick Exit prompt ON Quick Exit prompt OFF
ON I_______I 6 View Event Buffer prompt ON View Event Buffer prompt OFF
OFF I_______I 7-8 For future use
[62] Third User Display Mask
Default Option ON OFF
ON I_______I 1 System Test prompt ON System Test prompt OFF
ON I_______I 2 Time and Date prompt ON Time and Date prompt OFF
ON I_______I 3 Auto-Arm Control prompt ON Auto-Arm Days prompt OFF
ON I_______I 4 Auto-Arm Time prompt ON Auto-Arm Time prompt OFF
ON I_______I 5 Download Enable prompt ON Download Enable prompt OFF
ON I_______I 6 Bright Control prompt ON Bright Control prompt OFF
ON I_______I 7 Contrast Control prompt ON Contrast Control prompt OFF
ON I_______I 8 Buzzer Control prompt ON Buzzer Control prompt OFF
[63] Downloaded LCD Message Duration
Default: 003 I_______I_______I_______I (Valid entries are 000-255, 000=Unlimited Message Display. This number represents the number of times
the Downloaded message is cleared by pressing any key while the message is up after timeout)
[64] Key Options
Default Option ON OFF
ON I_______I 1 [F]ire Keys enabled [F]ire Keys disabled
ON I_______I 2 [A]uxiliary Keys enabled [A]uxiliary Keys disabled
ON I_______I 3 [P]anic Keys enabled [P]anic Keys disabled
OFF I_______I 4-8 For future use
[65] Fourth User Display Mask
Default Option ON OFF
ON I_______I 1 User Initiated Call-up Prompt ON User Initiated Call-up Prompt OFF
OFF I_______I 2 For future use
OFF I_______I 3 For future use
ON I_______I 4 Command Output #1 prompt ON Command Output #1 prompt OFF
ON I_______I 5 Command Output #2 prompt ON Command Output #2 prompt OFF
OFF I_______I 6-8 For future use
[66] Keypad Options
Default Option ON OFF
ON I_______I 1 Display Access Code when Programming Display ‘X’ when Programming
ON I_______I 2 Local Clock Display Enabled Local Clock Display Disabled
OFF I_______I 3 Local Clock Displays 24 Hour time Local Clock Displays AM/PM
ON I_______I 4 Auto Alarm Memory Scroll Enabled Auto Alarm Memory Scroll Disabled
OFF I_______I 5-8 For future use
[97] View Software Version
[98] Initiate Global Label Broadcast
All LCD programming is done per keypad. If more than one LCD keypad are present on the system, and the PC5400 receives labels, labels pro-
grammed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to broadcast labels:
Step 1 - Program one LCD keypad completely.
Step 2 - Make sure all LCD keypads are connected to the Keybus.
Step 3 - Enter Installer’s Programming, then enter Section [98] at the keypad that was programmed. The keypad will now broadcast all the informa-
tion programmed to all the other LCD keypads on the system.
Step 4 - When the keypad is finished press the [#] key to exit.
[99] Reset LCD EEPROM to Factory Defaults
ASCII Characters

45
UL Listed Commercial and Residential Installations
The installation requirements listed below must be met for the follow- Control of the Protected Premises
ing grades of service. In order to have a UL Certificated system the protected area is to be
Grade A Local under the responsibility of one ownership and management (i.e. one
The installation must have a bell UL Listed for mecantile local alarms business under one name). This may be a group of buildings
(AMSECO MBL10B with model AB-12 bell housing). attached or unattached with different addresses but under the
The digital communicator must be enabled. responsibility of someone having mutual interest. The person of
The control panel must be in the Attack Resistant Enclosure (DSC mutual interest is not the alarm installing company.
Model CMC-1). Bell Location
Swinger shutdown must be disabled. The alarm sounding device (bell) must be located where it can be
Grade B Central Station and Police Connect heard by the person or persons responsible for maintaining the secu-
The installation must have a bell UL Listed for mecantile local alarms rity system during the daily arming cycle.
(AMSECO MBL10B with model AB-12 bell housing). Protection of the Control Unit
The digital communicator must be enabled. The local control and the local power supply must be protected by
Ringback must be enabled. one of the following ways:
The control panel must be in the Attack Resistant Enclosure (DSC • The control unit and audible alarm device power supply must be
Model CMC-1). in a protected area which is armed 24 hours a day.
Swinger shutdown must be disabled. • Each partition shall arm the area protecting the control unit and
Grade C Central Station the audible alarm device power supply. This may require dupli-
The digital communicator must be enabled. cate protection armed by each partition. Access to this protected
Ringback must be enabled. area, without causing an alarm, will require that all partitions be
The control panel must be in the Attack Resistant Enclosure (DSC disarmed.
Model CMC-1). In all cases described above, the protected area for the control unit
Swinger shutdown must be disabled. must be programmed as not bypassable.
All Commercial Installations Casual Users
• The entry delay must not exceed 60 seconds The installer should caution the user(s) to not give system information
• The exit delay must not exceed 60 seconds. to casual users (e.g. codes, bypass methods, etc. to baby-sitters or
• The minimum bell cutoff time is 15 minutes. service people). Only the One-Time Use codes should be given to
casual users.
Residential Installations
• The entry delay must not exceed 45 seconds User Information
• The exit delay must not exceed 60 seconds. The installer should advise the users and note in the user instruction
• The minimum bell cutoff time is 4 minutes. manual:
• Service organization name and telephone number
Programming • The programmed exit time
The notes in the programming sections describing the system config- • The programmed entry time
urations for UL Listed installations must be implemented.

46
F CC C O M P L IA N C E S TAT E M E N T
CAUTION: Changes or modifications not expressly approved by Digital equivalent, in such a manner as to allow for easy, immediate disconnection of
Security Controls Ltd. could void your authority to use this equipment. the terminal equipment. Standard jacks shall be so arranged that, if the plug
This equipment has been tested and found to comply with the limits for a connected thereto is withdrawn, no interference to the operation of the equip-
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are ment at the customer’s premises which remains connected to the telephone
designed to provide reasonable protection against harmful interference in a network shall occur by reason of such withdrawal.
residential installation. This equipment generates, uses and can radiate radio INCIDENCE OF HARM Should terminal equipment or protective circuitry
frequency energy and, if not installed and used in accordance with the cause harm to the telephone network, the telephone company shall, where
instructions, may cause harmful interference to radio communications. How- practicable, notify the customer that temporary disconnection of service may
ever, there is no guarantee that interference will not occur in a particular be required; however, where prior notice is not practicable, the telephone
installation. If this equipment does cause harmful interference to radio or company may temporarily discontinue service if such action is deemed rea-
television reception, which can be determined by turning the equipment off sonable in the circumstances. In the case of such temporary discontinuance,
and on, the user is encouraged to try to correct the interference by one or the telephone company shall promptly notify the customer and will be given
more of the following measures: the opportunity to correct the situation.
• Re-orient the receiving antenna. ADDITIONAL TELEPHONE COMPANY INFORMATION The security control
• Increase the separation between the equipment and receiver. panel must be properly connected to the telephone line with a USOC RJ-31X
• Connect the equipment into an outlet on a circuit different from that telephone jack.
to which the receiver is connected. The FCC prohibits customer-provided terminal equipment be connected to
party lines or to be used in conjunction with coin telephone service. Intercon-
• Consult the dealer or an experienced radio/television technician for
nect rules may vary from state to state.
help.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The tele-
The user may find the following booklet prepared by the FCC useful: “How
phone company may make changes in its communications facilities, equip-
to Identify and Resolve Radio/Television Interference Problems”. This book-
ment, operations or procedures, where such actions are reasonably required
let is available from the U.S. Government Printing Office, Washington D.C.
and proper in its business. Should any such changes render the customer’s
20402, Stock # 004-000-00345-4.
terminal equipment incompatible with the telephone company facilities the
Im p o rta n t In for m a t i o n
This equipment complies with Part 68 of the FCC Rules. On the side of this customer shall be given adequate notice to the effect modifications to main-
equipment is a label that contains, among other information, the FCC regis- tain uninterrupted service.
tration number of this equipment. RINGER EQUIVALENCE NUMBER (REN) The REN is useful to determine the
NOTIFICATION TO TELEPHONE COMPANY The customer shall notify the tele- quantity of devices that you may connect to your telephone line and still have
phone company of the particular line to which the connection will be made, all of those devices ring when your telephone number is called. In most, but
and provide the FCC registration number and the ringer equivalence of the not all areas, the sum of the RENs of all devices connected to one line should
protective circuit. not exceed five (5.0). To be certain of the number of devices that you may con-
nect to your line, you may want to contact your local telephone company.
FCC Registration Number: F53CAN-32394-AL-E EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this
Ringer Equivalence Number: 0.0B telephone equipment, please contact the facility indicated below for informa-
tion on obtaining service or repairs. The telephone company may ask that
USOC Jack: RJ-31X
you disconnect this equipment from the network until the problem has been
TELEPHONE CONNECTION REQUIREMENTS Except for the telephone com- corrected or until you are sure that the equipment is not malfunctioning.
pany provided ringers, all connections to the telephone network shall be Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
made through standard plugs and telephone company provided jacks, or

AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué. NOTICE: The Industry Canada label identifies certified equipment. This
Cette étiquette certifie que le matériel est conforme à certaines normes certification means that the equipment meets certain telecommunica-
de protection, d’exploitation et de sécurité des réseaux de télécommuni- tions network protective, operational and safety requirements. Industry
cations. Industrie Canada n’assure toutefois pas que le matériel fonc- Canada does not guarantee the equipment will operate to the user’s sat-
tionnera à la satisfaction de l’utilisateur. isfaction.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de Before installing this equipment, users should ensure that it is permissi-
le raccorder aux installations de l’entreprise locale de télécommunica- ble to be connected to the facilities of the local telecommunications
tion. Le matériel doit également être installé en suivant une méthode company. The equipment must also be installed using an acceptable
acceptée de raccordement. L’abonné ne doit pas oublier qu’il est possi- method of connection. The customer should be aware that compliance
ble que la conformité aux conditions énoncées ci-dessus n’empêchent with the above conditions may not prevent degradation of service in
pas la dégradation du service dans certaines situations. some situations.
Les réparations de matériel homologué doivent être effectuées par un Repairs to certified equipment should be made by an authorized Cana-
centre d’entretien canadien autorisé désigné par le fournisseur. La dian maintenance facility designated by the supplier. Any repairs or
compagnie de télécommunications peut demander à l’utilisateur de alterations made by the user to this equipment, or equipment malfunc-
débrancher un appareil à la suite de réparations ou de modifications tions, may give the telecommunications company cause to request the
effectuées par l’utilisateur ou à cause de mauvais fonctionnement. user to disconnect the equipment.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de User should ensure for their own protection that the electrical ground
mise à la terre de la source d’énergie électrique, les lignes télépho- connections of the power utility, telephone lines and internal metallic
niques et les canalisations d’eau métalliques, s’il y en a, sont raccordés water pipe system, if present, are connected together. This precaution
ensemble. Cette précaution est particulièrement importante dans les may be particularly important in rural areas.
régions rurales. CAUTION: Users should not attempt to make such connections them-
AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccorde- selves, but should contact the appropriate electric inspection authority,
ments lui-même; il doit avoir recours à un service d’inspection des instal- or electrician, as appropriate.
lations électriques, ou à un électricien, selon le cas. The Load Number (LN) assigned to each terminal device denotes the
L’indice de charge (IC) assigné a chaque dispositif terminal indique, percentage of the total load to be connected to a telephone loop which
pour éviter toute surcharge, le pourcentage de la charge totale qui peut is used by the device, to prevent overloading. The termination on a loop
être raccordée à un circuit téléphonique bouclé utilisé par ce dispositif. may consist of any combination of devices subject only to the require-
La terminaison du circuit bouclé peut être constituée de n’importe quelle ment that the total of the Load Numbers of all the devices does not
combinaison de dispositifs, pourvu que la somme des indices de charge exceed 100.
de l’ensemble des dispositifs ne dépasse pas 100. The Load Number of this unit is 0.1B.
L’Indice de charge de ce produit est 0.1B.
 PC580 Module Compatibility
Module Compatible? Comments
Classic Escort (VPM-1) No
Escort5580 No
PC-16 Out No
PC5204 No
PC5208 No
PC5108 No
PC5108L No
PC5132 v1.X Yes No support for Wireless Keys, Pendants or Handheld Keypads
PC5132 v2.X Yes No identified Wireless Keys support
PC5132 v3.X Yes
PC5506 No
PC55XX Yes No Keypad zone support
PC55XXZ Yes
LCD5500 v1.X Yes No Keypad zone support; Some display messages not supported
LCD5500Z v2.X Yes
LCD600 No
LED615 No
SL-XX No
PC1500RK No
PC1555RKZ Yes
PC5908 No
PC5928 No
PC5400 Printer Yes Some printing messages not supported
Module v1.X to v2.1
PC5400 Printer Yes
Module v2.2
Links1000* Yes
Links2150* Yes
Links2450* Yes
Skyroute* Yes

*LINKS1000, LINKS2X50, and Skyroute have not been investigated by UL.

Changes for PC580 v2.3

The PC580 v2.3 software incorporates several new fea- New Downloading Software
tures and changes. The most important additions are Downloading software DLS-1 v6.7 must be used. Do not
listed below: attempt to perform downloading/uploading functions with
Number of Zones other software versions.
System expandable to 8 zones using keypad zone inputs Default Changes
and to 32 zones using the PC5132 wireless expansion • Section [006] Installer’s code: 5555
module. (See 1.2 “Additional Devices” on page 2.) • Section [160], Maximum Number of Dialing Attempts -
New Options & Features valid entries (000-015)
• New access code attribute option determines
whether the bell squawks on arming/disarming. (See
“[*][5] Programming Access Codes” on page 10.)
• New option allows bell squawk on Away arming only
(See 5.17 “Arming/Disarming Options” on page 23.)
• Users can restart the exit delay once by pressing the
Away key.

©1998 Digital Security Controls Ltd.

1645 Flint Road, Downsview, Ontario, Canada M3J 2J6
(416) 665-8460 • Fax (416) 665-7498 • 1-800-387-3630
www.dscgrp.com
Printed in Canada 29003297 R0