6-Speed Direct Shift Gearbox (DSG/02E) - Ross-Tech Wiki Page 1 of 5
Skip to content
ShopInfoF.A.Q.Download/UpdateManualUpgradesLiterature
Search: Go
6-Speed Direct Shift Gearbox (DSG/02E)
From Ross-Tech Wiki
General Information about this Transmission can be found in the Wikipedia entry
(http://en.wikipedia.org/wiki/Direct-Shift_Gearbox) . Additional information can be found in the
Official Factory Repair Information and sources such as Bentley Publisher's SSP (Self-Study
Program) (http://www.bentleypublishers.com//volkswagen/technical-training/vw-02e-direct-shift-
gearbox-ssp.html) .
Contents
◾ 1 Coding
◾ 2 Basic Setting
◾ 2.1 Transmission Tolerances (Engaged Calibration)
◾ 2.2 Transmission Tolerances (Synch. Point. Measurement)
◾ 2.3 Clutch Adaptation
◾ 2.4 Reset Values (Clutch Safety Function)
◾ 2.5 Reset Values (Pressure Adaptation)
◾ 2.6 Reset Values (Steering Wheel Paddle Installation)
◾ 2.7 Reset Values (ESP & Tip Cruise Control Installation)
◾ 3 Special Procedures
◾ 3.1 Defined Test Drive
◾ 3.1.1 Special Notes
◾ 4 Replacement
Coding
◾ When replacing this Mechatronic unit, simply copy the coding from the original Auto-Scan
and paste it into the New Coding section of the replacement followed by clicking [Do it!
(http://www.ross-tech.com/vcds/tour/recode_screen.html) ].
◾ If the original Coding is unknown, coding information can be found in the pop-up balloon
within the VCDS [Coding-07 (http://www.ross-tech.com/vcds/tour/recode_screen.html) ]
function.
http://wiki.ross-tech.com/wiki/index.php/6-Speed_Direct_Shift_Gearbox_(DSG/02E) 26.08.2016
6-Speed Direct Shift Gearbox (DSG/02E) - Ross-Tech Wiki Page 2 of 5
Basic Setting
Prerequisites:
◾ Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
◾ Selector Lever in P
◾ Ignition ON
◾ Engine ON (Idling) for one minute or more
◾ Brake Pedal operated (hold for the whole procedure)
◾ Throttle Pedal not operated
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test
drive.
[Select]
[02 - Transmission]
[Basic Settings - 04]
Transmission Tolerances (Engaged Calibration)
Group 061
[Go!]
◾ When you go to Basic Settings 061 and click GO the screen may look like this: Basic Settings
061 (http://wiki.ross-tech.com/wiki/images/3/35/02-04-061_start.png)
◾ Wait until the numbers quit moving and the trans will quit making noises. Basic Settings
switches to On when finished: Basic Settings 061 (http://wiki.ross-
tech.com/wiki/images/1/1e/02-04-061_end.png)
Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take
one minute.
Transmission Tolerances (Synch. Point. Measurement)
Group 060
[Go!]
◾ When you go to Basic Settings 060 and click GO the screen may look like this: Basic Settings
060 (http://wiki.ross-tech.com/wiki/images/a/a8/02-04-060_start.png)
◾ Wait until the numbers quit moving and the trans will quit making noises. Basic Settings
switches to On when finished: Basic Settings 060 (http://wiki.ross-
tech.com/wiki/images/3/3e/02-04-060_end.png)
Wait until Basic Settings has switched to ON and all numbers have stopped moving.
Clutch Adaptation
Control Module Software Version < 0800:
http://wiki.ross-tech.com/wiki/index.php/6-Speed_Direct_Shift_Gearbox_(DSG/02E) 26.08.2016
6-Speed Direct Shift Gearbox (DSG/02E) - Ross-Tech Wiki Page 3 of 5
Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Special notes.
◾ When found in the early software level (0627/0628) (8N) Audi TT:
◾ Basic Settings group 062 may take several minutes to complete. The final values may
report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished.
◾ If Basic Settings group 062 reports ERROR:| Group 062| Not | Available try test
driving the vehicle and repeating at normal operating temp.
Internal Ref: ST?ID=66725 and E?ID=309867
Control Module Software Version >= 0800 :
Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Clutch Safety Function)
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Pressure Adaptation)
Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Steering Wheel Paddle Installation)
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (ESP & Tip Cruise Control Installation)
Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
http://wiki.ross-tech.com/wiki/index.php/6-Speed_Direct_Shift_Gearbox_(DSG/02E) 26.08.2016
6-Speed Direct Shift Gearbox (DSG/02E) - Ross-Tech Wiki Page 4 of 5
[Done, Go Back]
Switch off Ignition, wait 10 Seconds and switch it back on.
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.
Special Procedures
Defined Test Drive
Suggested test drive after replacing the mechatronic or successful basic setting.
Prerequisites:
◾ Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
◾ Do Not use Cruise Control.
Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for
approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive,
Not Tiptronic Mode.
Evaluate creep and starting-off points.
Check for leaks.
NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any
remaining adaptations will be performed automatically during normal driving.
Special Notes
◾ Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed
after clicking the button, or the Basic Settings status does not switch to On, let the selected
group and procedure finish on its own.
◾ It is normal for the transmission to make noise while the tolerances are adapting. Do not exit
or abort the Basic Settings sequence prematurely if you hear clacking noises.
◾ Customers with TDI's have reported that an RPM range of 2000-2500 rpm is sufficient.
Replacement
http://wiki.ross-tech.com/wiki/index.php/6-Speed_Direct_Shift_Gearbox_(DSG/02E) 26.08.2016
6-Speed Direct Shift Gearbox (DSG/02E) - Ross-Tech Wiki Page 5 of 5
◾ Run and save a complete Auto-Scan and save it prior to Mechatronic unit removal. See the
Online Manual Auto-Scan (http://www.ross-tech.com/vcds/tour/autoscan.html) .
◾ Enter the original Coding into the New Coding section of the replacement controller.
◾ Complete Basic Settings
◾ Complete the Defined Test Drive
Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=6-Speed_Direct_Shift_Gearbox_
(DSG/02E)&oldid=8086"
Category: Transmissions
Unless otherwise noted, all content on this site is Copyright © 2000-2010 by Ross-Tech LLC. All
rights reserved.
"VCDS" is a Registered Trademark of Ross-Tech, LLC.
Ross-Tech is not affiliated with the Volkswagen Group in any way.
http://wiki.ross-tech.com/wiki/index.php/6-Speed_Direct_Shift_Gearbox_(DSG/02E) 26.08.2016
