<<Contents>> <<Index>>

General EJA130E
Specifications Differential Pressure Transmitter

GS 01C31B04-01EN [Style: S2]

The high performance differential pressure transmitter

EJA130E features single crystal silicon resonant
sensor and is suitable to measure liquid, gas, or
steam flow as well as liquid level, density and
pressure. EJA130E outputs a 4 to 20 mA DC signal
corresponding to the measured differential pressure.
Its accurate and stable sensor can also measure the
static pressure which can be shown on the integral
indicator or remotely monitored via BRAIN or HART
communications. Other key features include quick
response, remote set-up using communications and
self-diagnostics. FOUNDATION Fieldbus, PROFIBUS
PA and 1 to 5 V DC with HART (Low Power) protocol
types are also available. EJA-E series models in
their standard configuration, with the exception of
the Fieldbus, PROFIBUS and Low Power types,
are certified as complying with SIL 2 for safety
requirement.

 STANDARD SPECIFICATIONS Reference Accuracy of Calibrated Span

Refer to GS 01C31T02-01EN for Fieldbus (includes terminal-based linearity, hysteresis, and
communication type and GS 01C31T04-01EN for repeatability)
PROFIBUS PA communication type for the items
marked with “◊.” Measurement span H
Reference X ≤ span ±0.055% of Span
□ SPAN AND RANGE LIMITS accuracy X > span ±(0.005+0.01 URL/span)% of Span
X 100 kPa (400 inH2O)
Measurement inH2O mbar mmH2O
kPa URL
Span/Range (/D1) (/D3) (/D4) 500 kPa (2000 inH2O)
(upper range limit)
100 to
Span 1 to 100 4 to 400 10 to 1000
10000
M
-100 to -400 to -1000 to -10000 to Measurement span M
Range
100 400 1000 10000 Reference X ≤ span ±0.055% of Span
0.05 to 5 accuracy X > span ±(0.005+0.005 URL/span)% of Span
Span 5 to 500 20 to 2000 50 to 5000
kgf/cm2
H X 10 kPa (40 inH2O)
-500 to -2000 to -5000 to -5 to 5
Range URL
500 2000 5000 kgf/cm2 100 kPa (400 inH2O)
(upper range limit)

□ PERFORMANCE SPECIFICATIONS Square Root Output Accuracy

Zero-based calibrated span, linear output, wetted The square root accuracy is a percent of flow span.
parts material code S and silicone oil, unless Output Accuracy
otherwise mentioned.
50% or Greater Same as reference accuracy
For Fieldbus and PROFIBUS PA communication
types, use calibrated range instead of span in the Reference accuracy × 50
50% to Dropout point
following specifications. Square root output (%)

Specification Conformance Ambient Temperature Effects per 28°C (50°F)

EJA-E series ensures specification conformance to at Change
least ±3σ.
Capsule Effect
H ±(0.07% Span + 0.015% URL)
M ±(0.07% Span + 0.02% URL)

Yokogawa Electric Corporation GS 01C31B04-01EN

2-9-32, Nakacho, Musashino-shi, Tokyo, 180-8750 Japan ©Copyright June 2012
Tel.: 81-422-52-5690 Fax.: 81-422-52-2018 14th Edition April 2018
<<Contents>> <<Index>> 2
Static Pressure Effects per 6.9 MPa (1000 psi) □ FUNCTIONAL SPECIFICATIONS
Change
Output “◊”
Span Effects For 4 to 20 mA HART / BRAIN
M and H capsules (Output signal code D and J)
±0.1% of span Two wire 4 to 20 mA DC output with digital
Effect on Zero communications, linear or square root programmable.
Capsule Effect BRAIN or HART FSK protocol are superimposed on
H, M ±0.028% URL the 4 to 20 mA signal.
Output range: 3.6 mA to 21.6 mA
Overpressure Effects Output limits conforming to NAMUR NE43 can be
Overpressure condition: up to maximum working pre-set by option code C2 or C3.
pressure For 1 to 5 V HART (Output signal code Q)
M and H capsules, except for gold-plated diaphragm. Three or four wire low power 1 to 5 V DC output with
±0.03% of URL HART, linear or square root programmable. HART
Stability (All normal operating condition, including protocol are superimposed on the 1 to 5 V DC signal.
overpressure effects) Output range: 0.9 V to 5.4 V DC
M and H capsules Failure Alarm
±0.1% of URL per 10 years For 4 to 20 mA HART / BRAIN
Power Supply Effects(Output signal code D and J) (Output signal code D and J)
±0.005 % per Volt (from 21.6 to 32 V DC, 350Ω) Analog output status at CPU failure and hardware
Vibration Effects error;
Amplifier housing code 1 and 3: Up-scale: 110%, 21.6 mA DC or more (standard)
Less than 0.1% of URL when tested per the Down-scale: −5%, 3.2 mA DC or less
requirements of IEC60770-1 field or pipeline For 1 to 5 V HART (Output signal code Q)
with high vibration level (10-60 Hz, 0.21 mm Analog output status at CPU failure and hardware
displacement/60-2000 Hz 3 g) error;
Amplifier housing code 2: Up-scale: 110%, 5.4 V DC or more (standard)
Less than ±0.1% of URL when tested per the Down-scale: −5%, 0.8 V DC or less
requirements of IEC60770-1 field with general Damping Time Constant (1st order)
application or pipeline with low vibration level (10-60 Amplifier damping time constant is adjustable
Hz 0.15mm displacement /60-500 Hz 2g) from 0.00 to 100.00 sec by software and added to
Mounting Position Effects response time.
Rotation in diaphragm plane has no effect. Tilting Note: For BRAIN protocol type, when amplifier
up to 90 degree will cause zero shift up to 0.4 kPa software damping is set to less than 0.5 sec,
communication may occasionally be unavailble
(1.6 inH2O) which can be corrected by the zero
during the operation, especially while output
adjustment. changes dynamically. The default setting of
Response Time (Differential pressure) “◊” damping ensures stable communication.
M and H capsules: 150 ms Update Period “◊”
When amplifier damping is set to zero and including Differential pressure: 45 ms
dead time of 45 ms (nominal) Static pressure: 360 ms
Static Pressure Signal Range and Accuracy Zero Adjustment Limits
(For monitoring via communication or on Zero can be fully elevated or suppressed, within the
indicator. Includes terminal-based linearity, lower and upper range limits of the capsule.
hysteresis, and repeatability)
External Zero Adjustment
Range External zero is continuously adjustable with
Upper Range Value and Lower Range Value of the 0.01% incremental resolution of span. Re-range
static pressure can be set in the range between 0 can be done locally using the digital indicator with
and Maximum Working Pressure(MWP). The upper rangesetting switch.
range value must be greater than the lower range
value. Minimum setting span is 0.5 MPa(73 psi). Integral Indicator (LCD display, optional) “◊”
Measuring either the pressure of high pressure side 5-digit numerical display, 6-digit unit display and bar
or low pressure side is user-selectable. graph.
The indicator is configurable to display one or up to
Accuracy four of the following variables periodically.;
Absolute Pressure Measured differential pressure, differential pressure
1 MPa or higher: ±0.5% of span in %, scaled differential pressure, measured static
Less than 1 MPa: ±0.5%×(1 MPa/span) of span pressure. See also “Factory Setting.”
Gauge Pressure Reference
Gauge pressure reference is 1013 hPa (1 atm) Local Parameter Setting
Note: Gauge pressure variable is based on the above (Output signal code D, J and Q)
fixed reference and thus subject to be affected by Parameter configuration by the external zero
the change of atomospheric pressure. adjustment screw and push button (Integral indicator
code E) offers easy and quick setup for parameters of
Tag number, Unit, LRV, URV, Damping, Output mode
(linear/square root), Display out 1, and Re-range by
applying actual pressure (LRV/URV).

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN Feb. 10, 2017-00
<<Contents>> <<Index>> 3
Burst Pressure Limits Supply & Load Requirements
132 MPa (19100 psi) (Output signal code D and J. Optional features
Self Diagnostics or approval codes may affect electrical
CPU failure, hardware failure, configuration error, requirements.)
and over-range error for differential pressure, static With 24 V DC supply, up to a 550Ω load can be
pressure and capsule temperature. used. See graph below.
User-configurable process high/low alarm for
differential pressure and static pressure is also
available.
Signal Characterizer 600
(Output signal code D, J and Q) E-10.5
User-configurable 10-segment signal characterizer R=
External 0.0244 Digital
for 4 to 20 mA output. load Communication
SIL Certification resistance range
EJA-E series transmitters except Fieldbus, BRAIN and HART
PROFIBUS PA and 1-5V DC with HART (Low Power) 250
communication types are certified in compliance with
the following standards;
IEC 61508: 2010; Part1 to Part 7 R (Ω)
Functional Safety of Electrical/electronic/
programmable electronic related systems; SIL 2
capability for single transmitter use, SIL 3 capability 10.5 16.6 25.2 42
for dual transmitter use. Power supply voltage E (V DC)
F02E.ai

□ NORMAL OPERATING CONDITION Figure 2. Relationship Between Power Supply

(Optional features or approval codes may Voltage and External Load Resistance
affect limits.) (Output signal code D and J)

Ambient Temperature Limits

−40 to 85°C (−40 to 185°F) Supply Voltage “◊”
−30 to 80°C (−22 to 176°F) with LCD display For 4 to 20 mA HART / BRAIN
(Output signal code D and J)
Process Temperature Limits 10.5 to 42 V DC for general use and flameproof type.
−40 to 120°C (−40 to 248°F) 10.5 to 32 V DC for lightning protector
Ambient Humidity Limits (option code /A.)
0 to 100% RH 10.5 to 30 V DC for intrinsically safe, type n, or non-
Working Pressure Limits (Silicone oil) incendive.
Minimum voltage limited at 16.6 V DC for digital
Maximum Pressure Limits (MWP)
communications, BRAIN and HART
M and H capsule 32 MPa (4500 psi)
For 1 to 5 V HART (Output signal code Q)
Minimum Pressure Limit Power supply :
See graph below 9 to 28 V DC for general use and flame proof type.
Power Consumption :
0.96 mA to 3 mA, 27 mW
100(14.5) Atmospheric Load for 4 to 20 mA HART / BRAIN
pressure (Output signal code D and J)
Working 0 to 1290Ω for operation
pressure 250 to 600Ω for digital communication
kPa abs
(psi abs) Output Load for 1 to 5 V HART
(Output signal code Q)
Applicable range
1 MΩ or greater (meter input impedance)
10(1.4) Note that with three-wire connection, the cable length
may affect the measurement accuracy of the output
signal.
2.7(0.38) Communication Requirements “◊”
(Approval codes may affect electrical requirements.)
BRAIN
1(0.14)
-40 0 40 80 120 Communication Distance
(-40) (32) (104) (176) (248) Up to 2 km (1.25 miles) when using CEV
polyethylene-insulated PVC-sheathed cables.
Process temperature °C (°F) F01E.ai
Communication distance varies depending on type of
Figure 1. Working Pressure and Process Temperature cable used.
Load Capacitance
0.22 µF or less

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN Feb. 10, 2017-00
<<Contents>> <<Index>> 4
Load inductance Weight
3.3 mH or less [Installation code 7, 8 and 9]
Input impedance of communicating device 6.8 kg (14.3 lb) without integral indicator, mounting
10 kΩ or more at 2.4 kHz. bracket, and process connector.
Add 1.5 kg (3.3 lb) for amplifier housing code 2.
EMC Conformity Standards
EN 61326-1 Class A, Table2 Connections
EN 61326-2-3 Refer to “MODEL AND SUFFIX CODES.”
EN 61326-2-5 (for fieldbus) Process Connection of Cover Flange: IEC61518
European Pressure Equipment Directive
2014/68/EU < Related Instruments>
Sound Engineering Practice FieldMate Versatile Device Management Wizard:
Refer to GS 01R01A01-01E.
With option code /PE3 BRAIN TERMINAL: Refer to GS 01C00A11-00E
Power Distributor: Refer to GS 01B04T01-02E or
GS 01B04T02-02E
Category III, Module H, Type of Equipment: Pressure
Accessory-Vessel, Type of Fluid: Liquid and Gas,
Group of Fluid: 1 and 2 < Reference >
• ; Registered trademark of Yokogawa
EU RoHS Directive
Electric Corporation.
EN 50581
• FieldMate; Registered trademark of Yokogawa
Safety Requirement Standards Electric Corporation.
EN 61010-1, C22.2 No.61010-1 • Teflon; Trademark of E.I. DuPont de Nemours &
• Installation category: I Co.
(Anticipated transient overvoltage 330 V) • Hastelloy; Trademark of Haynes International Inc.
• Pollution degree: 2 • HART®: Registered trademark of FieldComm
• Indoor/Outdoor use Group.
• FOUNDATION Fieldbus; Trademark of FieldComm
□ PHYSICAL SPECIFICATIONS Group.
Wetted Parts Materials • PROFIBUS; Registered trademark of Profibus
Nutzerorganisation e.v., Karlsruhe, Germany.
Diaphragm, cover flange, process connector,
Other company names and product names used in
capsule gasket, and vent/drain plug
this material are registered trademarks or trademarks
Refer to “MODEL AND SUFFIX CODES.”
of their respective owners.
Process connector O-ring
Fluorinated rubber
Non-wetted Parts Materials
Bolting
B7 carbon steel, 316L SST or 660 SST
Housing
• Low copper cast aluminum alloy
• Low copper cast aluminum alloy with corrosion
resistance properties (copper content ≤ 0.03%,
iron content ≤ 0.15%) (optional)
• ASTM CF-8M Stainless steel (optional)
Coating of housing
[for aluminum housing]
Urethane curing type polyester resin powder coating
Mint-green paint (Munsell 5.6BG 3.3/2.9 or its
equivalent)
[for option code /P or /X2]
Epoxy and polyurethane resin solvent coating
Degrees of protection
IP66/IP67, Type 4X
Cover O-rings
Buna-N, fluoro-rubber (optional)
Name plate and tag
316 SST
Fill fluid
Silicone, fluorinated oil (optional)

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN April 10, 2018-00
<<Contents>> <<Index>> 5
 MODEL AND SUFFIX CODES
Model Suffix Codes Description
EJA130E ............................... Differential pressure transmitter
Output signal -D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (BRAIN protocol)
-J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (HART 5/HART 7 protocol)*1
-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (FOUNDATION Fieldbus protocol, refer to
GS 01C31T02-01EN)
-G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (PROFIBUS PA protocol, refer to
GS 01C31T04-01EN)
-Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low Power, 1 to 5 V DC with digital communication (HART 7 protocol)
Measurement M . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 100 kPa (4 to 400 inH2O)
span (capsule) H . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 to 500 kPa (20 to 2000 inH2O)
Wetted parts S . . . . . . . . . . . . . . . . . . . . . . . . . Refer to “Wetted Parts Material” Table below.
material *2
Process connections 3 . . . . . . . . . . . . . . . . . . . . . . with 1/4 NPT female process connector*3
4 . . . . . . . . . . . . . . . . . . . . . . with 1/2 NPT female process connector*3
► 5 . . . . . . . . . . . . . . . . . . . . . . without process connector (1/4 NPT female on the cover flanges)
Bolts and nuts materia J . . . . . . . . . . . . . . . . . . . B7 carbon steel
G . . . . . . . . . . . . . . . . . . . 316L SST
C . . . . . . . . . . . . . . . . . . . 660 SST
Installation -7 . . . . . . . . . . . . . . . . . Vertical piping, left side high pressure, and process connection downside
-8 . . . . . . . . . . . . . . . . . Horizontal piping and right side high pressure
► -9 . . . . . . . . . . . . . . . . . Horizontal piping and left side high pressure
-U . . . . . . . . . . . . . . . . . Universal flange
Amplifier housing 1 . . . . . . . . . . . . . . Cast aluminum alloy
3 . . . . . . . . . . . . . . Cast aluminum alloy with corrosion resistance properties*4
2 . . . . . . . . . . . . . . ASTM CF-8M stainless steel*5
Electrical connection 0 . . . . . . . . . . . G1/2 female, one electrical connection without blind plugs
► 2 . . . . . . . . . . . 1/2 NPT female, two electrical connections without blind plugs
4 . . . . . . . . . . . M20 female, two electrical connections without blind plugs
5 . . . . . . . . . . . G1/2 female, two electrical connections and a blind plug*6
7 . . . . . . . . . . . 1/2 NPT female, two electrical connections and a blind plug*6
9 . . . . . . . . . . . M20 female, two electrical connections and a blind plug*6
A . . . . . . . . . . . G1/2 female, two electrical connections and a SUS316 blind plug
C . . . . . . . . . . . 1/2 NPT female, two electrical connections and a SUS316 blind plug
D . . . . . . . . . . . M20 female, two electrical connections and a SUS316 blind plug
Integral indicator D . . . . . . . . Digital indicator*7
E . . . . . . . . Digital indicator with the range setting switch (push button)*8
► N . . . . . . . . None
Mounting bracket ► B . . . . . . 304 SST 2-inch pipe mounting, flat type (for horizontal piping)
D . . . . . . 304 SST or SCS13A 2-inch pipe mounting, L type (for vertical piping)
J . . . . . . 316 SST 2-inch pipe mounting, flat type (for horizontal piping)
K . . . . . . 316 SST or SCS14A 2-inch pipe mounting, L type (for vertical piping)
N . . . . . . None
Optional Codes / Optional specification

The “►” marks indicate the most typical selection for each specification.
*1: HART 5 or HART 7 is selectable. Specify upon ordering.
*2: Users must consider the characteristics of selected wetted parts material and influence of process fluids. Specifying
inappropriate materials has the potential to cause serious damage to human body and plant facilities resulted from an
unexpected leak of the corrosive process fluids.
*3: Lower limit of ambient and process temperature is -15°C.
*4: Not applicable for electrical connection code 0, 5, 7, 9 and A.
*5: Not applicable for electrical connection code 0, 5, 7 and 9.
*6: Material of a blind plug; aluminum alloy for code 5 and 9, and SUS304 for code 7.
*7: Not applicable for output signal code G.
*8: Not applicable for output signal code F.
Table. Wetted Parts Materials

Wetted parts
Cover flange Process connector Capsule Capsule gasket Vent/Drain plug
material code
Hastelloy C-276 (Diaphragm)
*2
S# F316 SST ASTM CF-8M *1 Teflon-coated 316L SST 316 SST
F316L SST, 316L SST (Others)
*1: Cast version of 316 SST. Equivalent to SCS14A.
*2: Hastelloy C-276 or ASTM N10276.
The ‘#’marks indicate the construction materials conform to NACE material recommendations per MR0175/ISO15156.
Please refer to the latest standards for details. Selected materials also conform to NACE MR0103.

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN June 1, 2017-00
<<Contents>> <<Index>> 6
 OPTIONAL SPECIFICATIONS (For Explosion Protected type) “◊”
For other agency approvals and marine approvals, please refer to GS 01C25A20-01EN.

Item Description Code

Factory Mutual FM Explosionproof Approval *1
(FM) Applicable Standard: FM3600, FM3615, FM3810, ANSI/NEMA 250
Explosionproof for Class I, Division 1, Groups B, C and D, Dust-ignitionproof for Class II/III, Division 1,
FF1
Groups E, F and G, in Hazardous locations, indoors and outdoors (Enclosure: Type 4X)
“FACTORY SEALED, CONDUIT SEAL NOT REQUIRED.”
Temperature class: T6, Amb. Temp.: –40 to 60°C (–40 to 140°F)
FM Intrinsically safe Approval *1*3
Applicable Standard: FM3600, FM3610, FM3611, FM3810
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1,
Groups E, F & G and Class III, Division 1, Class I, Zone 0, in Hazardous Locations, AEx ia IIC
Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division. 2,
FS1
Groups F & G, Class I, Zone 2, Group IIC, in Hazardous Locations
Enclosure: Type 4X, Temp. Class: T4, Amb. Temp.: –60 to 60°C (–75 to 140°F)
Intrinsically Safe Apparatus Parameters
[Groups A, B, C, D, E, F and G] Vmax=30 V, Imax=200 mA, Pmax=1 W, Ci=6 nF, Li=0 µH
[Groups C, D, E, F and G] Vmax=30 V, Imax=225 mA, Pmax=1 W, Ci=6 nF, Li=0 µH
Combined FF1 and FS1 *1*3 FU1
ATEX ATEX Flameproof Approval *1
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-1:2007 (“2014” from August 1, 2017),
EN 60079-31:2014
Certificate: KEMA 07ATEX0109 X
II 2G, 2D Ex d IIC T6...T4 Gb (“Ex db IIC T6...T4 Gb” from August 1, 2017), Ex tb IIIC T85°C Db
Degree of protection: IP66/IP67 KF22
Amb. Temp. (Tamb) for gas-proof :
T4; –50 to 75°C (–58 to 167°F), T5; –50 to 80°C (–58 to 176°F), T6; –50 to 75°C (–58 to 167°F)
Process Temp. for gas-proof (Tp):
T4; –50 to 120°C (–58 to 248°F), T5; –50 to 100°C (–58 to 212°F), T6; –50 to 85°C (–58 to 185°F)
Max. surface Temp. for dust-proof: T85°C (Tamb: –30 to 75°C, Tp: –30 to 85°C) *2
ATEX Intrinsically safe Approval *1*3
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012
Certificate: DEKRA 11ATEX0228 X
II 1G, 2D Ex ia IIC T4 Ga, Ex ia IIIC T85°C T100°C T120°C Db
Degree of protection: IP66/IP67
KS21
Amb. Temp. (Tamb) for EPL Ga: –50 to 60°C (–58 to 140°F)
Maximum Process Temp. (Tp) for EPL Ga:120°C
Electrical data: Ui=30 V, Ii=200 mA, Pi=0.9 W, Ci=27.6 nF, Li=0 µH
Amb. Temp. for EPL Db: –30 to 60°C *2
Max. surface Temp. for EPL Db: T85°C (Tp: 80°C), T100°C (Tp: 100°C), T120°C (Tp: 120°C)
Combined KF22, KS21 and ATEX Intrinsically safe Ex ic *1*3
[ATEX Intrinsically safe Ex ic]
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 KU22
II 3G Ex ic IIC T4 Gc, Amb. Temp.: –30 to 60°C (–22 to 140°F) *2
Ui=30 V, Ci=27.6 nF, Li=0 μH

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN June 1, 2017-00
<<Contents>> <<Index>> 7
Item Description Code
Canadian CSA Explosionproof Approval *1
Standards Certificate: 2014354
Association Applicable Standard: C22.2 No.0, C22.2 No.0.4, C22.2 No.0.5, C22.2 No.25, C22.2 No.30,
(CSA) C22.2 No.94, C22.2 No.60079-0, C22.2 No.60079-1, C22.2 No.61010-1, C22.2 No.61010-2-030
Explosion-proof for Class I, Groups B, C and D.
Dustignition-proof for Class II/III, Groups E, F and G.
When installed in Division 2, “SEAL NOT REQUIRED” Enclosure: Type 4X,
Temp. Code: T6...T4
CF1
Ex d IIC T6...T4 Enclosure: IP66/IP67
Max.Process Temp.: T4;120°C(248°F), T5;100°C(212°F), T6; 85°C(185°F)
Amb.Temp.: –50 to 75°C(–58 to 167°F) for T4, –50 to 80°C(–58 to 176°F) for T5,
–50 to 75°C(–58 to 167°F) for T6 *2
Process Sealing Certification
Dual Seal Certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required
Primary seal failure annunciation: at the zero adjustment screw
CSA Intrinsically safe Approval *1*3
Certificate: 1606623
[For CSA C22.2]
Applicable Standard: C22.2 No.0, C22.2 No.0.4, C22.2 No.25, C22.2 No.94, C22.2 No.157,
C22.2 No.213, C22.2 No.61010-1, C22.2 No.60079-0, C22.2 No.61010-2-030
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1, Groups E, F & G,
Class III, Division 1, Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division 2,
Groups F & G, Class III, Division 1
Enclosure: Type 4X, Temp. Code: T4 Amb. Temp.: –50 to 60°C(–58 to 140°F) *2
Electrical Parameters: [Intrinsically Safe] Vmax=30V, Imax=200mA, Pmax=0.9W, Ci=10nF, Li=0 µH
[Nonincendive] Vmax=30V, Ci=10nF, Li=0 µH CS1
[For CSA E60079]
Applicable Standard: CAN/CSA E60079-11, CAN/CSA E60079-15, IEC 60529:2001
Ex ia IIC T4, Ex nL IIC T4 Enclosure: IP66/IP67
Amb. Temp.: –50 to 60°C(–58 to 140°F) *2, Max. Process Temp.: 120°C(248°F)
Electrical Parameters: [Ex ia] Ui=30V, Ii=200mA, Pi=0.9W, Ci=10nF, Li=0 µH
[Ex nL] Ui=30V, Ci=10nF, Li=0 µH
Process Sealing Certification
Dual Seal Certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required
Primary seal failure annunciation: at the zero adjustment screw
Combined CF1 and CS1 *1*3 CU1
IECEx IECEx Flameproof Approval *1
Applicable Standard: IEC 60079-0:2011, IEC60079-1:2007-4
Certificate: IECEx CSA 07.0008
Flameproof for Zone 1, Ex d IIC T6...T4 Gb Enclosure: IP66/IP67 SF2
Max.Process Temp.: T4;120°C(248°F), T5;100°C(212°F), T6; 85°C(185°F)
Amb.Temp.: –50 to 75°C(–58 to 167°F) for T4, –50 to 80°C(–58 to 176°F) for T5,
–50 to 75°C(–58 to 167°F) for T6
IECEx Intrinsically safe and Flameproof Approval *1*3
Intrinsically safe Ex ia
Certificate: IECEx DEK 11.0081X
Applicable Standard: IEC 60079-0:2011, IEC 60079-11:2011
Ex ia IIC T4 Ga Enclosure: IP66/IP67
Amb. Temp.: –50 to 60 °C(–58 to 140 °F), Max. Process Temp.: 120 °C(248 °F)
Electrical Parameters: Ui=30 V, Ii=200 mA, Pi=0.9 W, Ci=27.6 nF, Li=0 μH
Intrinsically safe Ex ic
Certificate: IECEx DEK 13.0061X
Applicable Standard: IEC 60079-0:2011, IEC 60079-11:2011
SU21
Ex ic IIC T4 Gc IP code: IP66
Amb. Temp.: –30 to 60°C(–22 to 140°F) *2, Max. Process Temp.: 120°C(248°F)
Electrical Parameters: Ui=30V,Ci=27.6 nF, Li=0 μH
Flameproof
Certificate: IECEx CSA 07.0008
Applicable Standard: IEC 60079-0:2011, IEC60079-1:2007-4
Flameproof for Zone 1, Ex d IIC T6...T4 Gb Enclosure: IP66/IP67
Max.Process Temp.: T4;120°C(248°F), T5;100°C(212°F), T6; 85°C(185°F)
Amb.Temp.: –50 to 75°C(–58 to 167°F) for T4, –50 to 80°C(–58 to 176°F) for T5,
–50 to 75°C(–58 to 167°F) for T6
*1: Applicable for Electrical connection code 2, 4, 7, 9, C and D.
*2: Lower limit of ambient temperature is –15°C (5°F) when /HE is specified.
*3: Not applicable for output signal code Q.

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN June 1, 2017-00
<<Contents>> <<Index>> 8
 OPTIONAL SPECIFICATIONS
Item Description Code
Painting Color change Amplifier cover only*2 P
Amplifier cover and terminal cover, Munsell 7.5 R4/14 PR
Coating change Anti-corrosion coating*1 X2
316 SST exterior parts 316 SST zero-adjustment screw and setscrews*3 HC
Fluoro-rubber O-ring All O-rings of amplifier housing. Lower limit of ambient temperature: –15°C (5°F) HE
Lightning protector Transmitter power supply voltage: 10.5 to 32 V DC (10.5 to 30 V DC for intrinsically safe type.)
Allowable current: Max. 6000 A (1×40 µs), Repeating 1000 A (1×40 µs) 100 times A
Applicable Standards: IEC 61000-4-4, IEC 61000-4-5
Oil-prohibited use*4 Degrease cleansing treatment K1
Degrease cleansing treatment with fluorinated oilfilled capsule.
K2
Operating temperature −20 to 80°C (−4 to 176°F)
Oil-prohibited use with Degrease cleansing and dehydrating treatment K5
dehydrating treatment*4 Degrease cleansing and dehydrating treatment with fluorinated oilfilled capsule.
K6
Operating temperature −20 to 80°C ( −4 to 176°F)
Capsule fill fluid Fluorinated oil filled in capsule
K3
Operating temperature −20 to 80°C (−4 to 176°F)
Calibration units*5 P calibration (psi unit) D1
bar calibration (bar unit) (See Table for Span and Range Limits.) D3
M calibration (kgf/cm2 unit) D4
Long vent*6 Total length: 119 mm (standard: 34 mm); Total length when combining with option code K1,
U1
K2, K5, and K6: 130 mm. Material: 316 SST
Gold-plated capsule gasket *7 Gold-plated 316L SST capsule gasket. Without drain and vent plugs. GS
Gold-plated diaphragm *18 Surface of isolating diaphragms are gold plated, effective Gold plate thickness: 3 μm A1
for hydrogen permeation. Gold plate thickness: 10 μm A2
Output limits and failure Failure alarm down-scale : Output status at CPU failure and hardware error is −5%, 3.2mA DC
C1
operation*8 or less for 4 to 20 mA output type, and −5%, 0.8V DC or less for 1 to 5 V output type.
Failure alarm down-scale: Output status at CPU
NAMUR NE43 Compliant C2
failure and hardware error is −5%, 3.2 mA DC or less.
Output signal limits:
3.8 mA to 20.5 mA *17 Failure alarm up-scale: Output status at CPU
C3
failure and hardware error is 110%, 21.6 mA or more.
Body option*9 Right side high pressure, without drain and vent plugs N1
Terminal N1 and Process connection, based on IEC61518 with female thread on both sides of cover
Side N2
flange, with blind kidney flanges on back.
L H N2, and Material certificate for cover flange, diaphragm, capsule body, and blind kidney flange N3
F03E.ai

Wired tag plate 316 SST tag plate wired onto transmitter N4
Data configuration at factory*10 Software damping, Descriptor,
Data configuration for HART communication type CA
Message
Data configuration for BRAIN communication type Software damping CB
European Pressure PED 2014/68/EU
Equipment Directive*11 Category: III, Module: H, Type of Equipment: Pressure Accessory-Vessel, PE3
Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2
Material certificate*12 Cover flange *13 M01
Cover flange, Process connector *14 M11
Pressure test/ Nitrogen(N2) Gas or Water*16
Test Pressure: 32 MPa(4500 psi) T09
Leak test certificate*15 Retention time: one minute
*1: Not applicable with color change option. Not applicable for amplifier housing code 2.
*2: Not applicable for amplifier housing code 2 and 3.
*3: The specification is included in amplifier code 2.
*4: Applicable for Wetted parts material code S.
*5: The unit of MWP (Max. working pressure) on the name plate of a housing is the same unit as specified by option codes D1,
D3, and D4.
*6: Applicable for vertical impulse piping type (Installation code 7) and Wetted parts material code S.
*7: Applicable for wetted parts material code S; process connection code 5; and installation code 8 and 9. Not applicable for
option code U1, N2, N3 and M11. No PTFE is used for wetted parts.
*8: Applicable for output signal codes D and J. The hardware error indicates faulty amplifier or capsule.
*9: Applicable for wetted parts material code S; process connection codes 3, 4, and 5; installation code 9; and mounting
bracket code N. Process connection faces on the other side of zero adjustment screw.
*10: Also see ‘Ordering Information’.
*11: If compliance with category III is needed, specify this option code.
*12: Material traceability certification, per EN 10204 3.1B.
*13: Applicable for process connections codes 5.
*14: Applicable for process connections codes 3 and 4.
*15: The unit on the certificate is always Pa unit regardless of selection of option code D1, D3 or D4.
*16: Pure nitrogen gas or pure water is used for oil-prohibited use (option codes K1, K2, K5, and K6).
*17: The 1 to 5 V voltage output corresponding to 4 to 20 mA current output is applied to output signal code Q which is non-
compliant to NAMUR NE43.
*18: /A2 is not applicable with FM approval.

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN Feb. 10, 2017-00
<<Contents>> <<Index>> 9
 DIMENSIONS
Unit: mm (approx.inch)

● Vertical Impulse Piping Type (INSTALLATION CODE ‘7’)

Electrical connection
for code 5, 9, A, and D.

(0.24)
256(10.1) 132(5.2)

6
197(7.76) 110(4.33)

(2.13)
9 39 2-inch pipe

54
97 143(5.63)
(3.82) (0.35) (1.54) (O.D. 60.5 mm)
Mounting bracket Vent/Drain plugs
(L-type,optional) External indicator
Conduit connection
(2.05)
52

(optional)
Integral indicator
(optional)
(4.88)
124
277(10.9)

192(7.56)*2
ø70(2.76)
ø78(3.07)
(3.74)
95
(3.66)
93

Process
Conduit connector
connection (optional)
Process connection Zero adjustment High 54 Low
pressure (2.13) pressure
Ground terminal side*1 side*1 F04E.ai

● Horizontal Impulse Piping Type (INSTALLATION CODE ‘9’)

(For CODE ‘8’, refer to the notes below.)
Conduit connection
External indicator 116(4.57) 93(3.66) 110(4.33)
Zero
Conduit connection adjustment 9*4 39
95(3.74) Integral indicator
(optional) (0.35) (1.54)
(optional)
ø78(3.07)

54 (2.76)
(2.13)
ø70

6
197(7.76)
159(6.26)

143(5.63)
(0.24)
Vent plug, Ground
Drain plug*5 terminal Vent plug*5

Electrical connection Vent plug*5

for code 5, 9, A, and D. Process
connection
Drain plug*5
Drain plug*5
124(4.88)

68
54(2.13) Low
(2.68) High
pressure pressure
Process connector side*1 side*1
169(6.65)
(optional)
(1.63)
41.3

(1.85)
47

Mounting bracket
(Flat-type,optional) 2-inch pipe
(O.D. 60.5 mm)
154(6.06)*3
F05E.ai

*1: When installation code 8 is selected, high and low pressure side on above figure are reversed.
(i.e. High pressure side is on the right side.)
*2: When option code K1, K2, K5 or K6 is selected, add 15mm(0.59 inch) to the value in the figure.
*3: When option code K1, K2, K5 or K6 is selected, add 30mm(1.18 inch) to the value in the figure.
*4: 15mm (0.59 inch) for right side high pressure.
*5: Not available when option code GS is selected.
*6: When electrical connection code 7 or C is selected, a blind plug is protruded upto 8 mm from the conduit connection.

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN June 1, 2017-00
<<Contents>> <<Index>> 10
Unit: mm (approx.inch)

● Universal Flange (INSTALLATION CODE ‘U’)

External indicator 85(3.35) 93(3.66) Zero 110(4.33)

Conduit connection Conduit connection adjustment
(optional) 9 39
95(3.74) Integral indicator (0.35) (1.54)
54 (optional)

ø78(3.07)
(2.13)

(2.76)
6

ø70
159(6.26)

(0.24)

143(5.63)
197(7.76)
Ground terminal

Electrical connection
for code 5, 9, A, and D.
Vent plug
Drain plug
68 Drain plug
Process connection 54
Vent plug (2.68) High (2.13) Low
169(6.65) Process connector pressure 154(6.06)*1 pressure
Drain plug side side
(optional)
F06E.ai

*1: When Option code K1, K2, K5, or K6 is selected, add 30 mm (1.18 inch) to the value.
*2: When electrical connection code 7 or C is selected, a blind plug is protruded upto 8 mm from the conduit connection.

● Terminal Configuration ● Terminal Wiring for 4 to 20 mA output,

FOUNDATION Fieldbus and PROFIBUS PA
communication types
+ 1
Power supply and output terminals
SUPPLY – 2

CHECK + 3
– 2
External indicator (ammeter) terminals*1*2

Ground terminal

*1: When using an external indicator or check meter, the internal

resistance must be 10 Ω or less.
*2: Not available for FOUNDATION Fieldbus and PROFIBUS PA
Terminal 1 Terminal 3 communication types.
Terminal 2
● Terminal Wiring for 1 to 5 V output
+ 1
Power supply terminals
SUPPLY – 2

VOUT + 3 1 to 5 V DC with HART communication

– 2 terminals
Ground terminal

Three or four wire connection. For four wire connection, both supply
and signal lines use SUPPLY - terminal.
F07E.ai

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN June 1, 2017-00
<<Contents>> <<Index>> 11

< Ordering Information > “◊” < Factory Setting > “◊”
Specify the following when ordering
Tag number As specified in order
1. Model, suffix codes, and option codes
2. Calibration range and units Software
‘2.00 s’ or as specified in order
1) Calibration range can be specified with range damping *1
value specifications up to 5 digits (excluding Output mode ‘Linear’ unless otherwise specified in order
any decimal point) for low or high range limits Calibration range
As specified in order
within the range of -32000 to 32000. When lower range value
reverse range is designated, specify Lower Calibration range
Range Value(LRV) as greater than Upper Range upper range As specified in order
Value(URV). When square root output mode is value
specified, LRV must be “0 (zero) ”. Selected from mmH2O, mmH2O(68°F),
2) Specify only one unit from the table, ‘Factory mmAq*2, mmWG*2, mmHg, Pa, hPa*2,
setting.’ Calibration range kPa, MPa, mbar, bar, gf/cm2,
3. Select linear or square root for output mode and unit kgf/cm2, inH2O, inH2O(68°F), inHg, ftH2O,
ftH2O(68°F) or psi. (Only one unit can be
display mode. specified.)
Note: If not specified, the instrument is shipped set for
linear mode. Designated differential pressure value
4. Display scale and units (for transmitters equipped specified in order. (% or user scaled
Display setting
value.) Display mode ‘Linear’ or ‘Square
with the integral indicator only)
root’ is also as specified in order.
Specify either 0 to 100 % or ‘Range and Unit’ for
engineering units scale: ‘0 to 32 MPa’ for M and H capsule,
Static pressure
absolute value.
Scale range can be specified with range limit display range
Measuring high pressure side.
specifications up to 5 digits (excluding any decimal
point) for low or high range limits within the range *1: To specify these items at factory, option code CA
of -32000 to 32000. Unit display consists of 6-digit, or CB is required.
therefore, if the specified scaling unit excluding ‘/’ is *2: Not available for HART protocol type.
longer than 6-characters , the first 6 characters will
be displayed on the unit display. < Material Cross Reference >
5. HART PROTOCOL
When output signal code is “J”, specify the HART ASTM JIS
protocol revision “5” or “7”. 316 SUS316
6. TAG NO (if required) F316 SUSF316
Specified characters (up to 16 characters for 316L SUS316L
BRAIN, 22 characters for HART, or 16 characters
F316L SUSF316L
for /N4 tag) are engraved on the stainless steel tag
plate fixed on the housing. 304 SUS304
7. SOFTWARE TAG (for HART only. if required) F304 SUSF304
Specified characters (up to 32 characters) are set 660 SUH660
as “Tag” (the first 8 characters) and “Long tag”*1 B7 SNB7
(32 characters) in the amplifier memory. Use CF-8M SCS14A
alphanumeric capital letters.
When the “SOFTWARE TAG” is not specified,
specified “TAG NO” is set as “Tag” (the first 8 <Information on EU WEEE Directive>
characters) and “Long tag”*1 (22 characters) in the EU WEEE (Waste Electrical and Electronic Equipment)
amplifier memory. Directive is only valid in the EU.
*1: applicable only when HART 7 is selected. This instrument is intended to be sold and used only
8. Other factory configurations (if required) as a part of equipment which is excluded from WEEE
Specifying option code CA or CB will allow further Directive, such as large-scale stationary industrial
configuration at factory. Following are configurable tools, a large-scale fixed installation and so on, and,
items and setting range. therefore, subjected to the exclusion from the scope
[/CA : For HART communication type] of the WEEE Directive. The instrument should be
1) Descriptor (up to 16 characters) disposed of in accordance with local and national
2) Message (up to 30 characters) legislation/regulations.
3) Software damping in second (0.00 to 100.00)
[/CB : For BRAIN communication type]
1) Software damping in second (0.00 to 100.00)

All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 01C31B04-01EN April 10, 2018-00
Subject to change without notice.