Scribd
Upload
445 views1 page

Coin Mechanisms Inc.: Unit Specifications

Coin Mechanisms Inc. produces coin acceptor Model MC-40 OE. The unit has standard specifications including a 7-pin customer interface requiring a Molex or AMP mating connector. It operates from 11-15V DC and has open collector outputs for sense, credit, and tilt signals. The mechanical design includes a standard chassis and coil configuration that accepts coins from 1.196-1.470 inches in diameter and 0.081-0.115 inches thick, typically processing 8 coins per second with over 98% acceptance of valid coins.

Uploaded by

Elvis Linares
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
445 views1 page

Coin Mechanisms Inc.: Unit Specifications

Coin Mechanisms Inc. produces coin acceptor Model MC-40 OE. The unit has standard specifications including a 7-pin customer interface requiring a Molex or AMP mating connector. It operates from 11-15V DC and has open collector outputs for sense, credit, and tilt signals. The mechanical design includes a standard chassis and coil configuration that accepts coins from 1.196-1.470 inches in diameter and 0.081-0.115 inches thick, typically processing 8 coins per second with over 98% acceptance of valid coins.

Uploaded by

Elvis Linares
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

COIN MECHANISMS INC.

Where The Money Meets The Machine


PO Box 5128, 400 Regency Drive, Glendale Heights, IL 60139-5128 VOICE: 1-630-924-7070 FAX: 1-630-924-7088

UNIT SPECIFICATIONS Model : MC-40 OE Body Style : Standard

CMI # : 66460206 I/F Cable : None Personality : PR-14


Optic Emulation PCB : 0927-000530 Blank PCB : 0827-000120
Firmware : 0950-000007 FW Desc :
Minimum Maximum
POWER SUPPLY
Operating Voltage Range 11V DC 15V DC
Nominal Input
Typical Current Draw - IDLE 100 mA 128 mA
12V DC
Typical Current Draw - PEAK 285 mA 340 mA

CUSTOMER INTERFACE Requires mating connector MOLEX P/N 22-01-3077 (terminals 08-52-0123) or AMP P/N 770602-7
(terminals 770666-1)
7-Pin Molex ID: 7M1.1A

PIN OUT PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7

I/O Ground Output Output Output - Input Control IN

FUNCTION GROUND SENSE (OC) TILT CREDIT - POWER 12V INHIBIT

OUTPUTS TYPE V Max. I Max Pulse Width

SENSE Open Collector 30V DC 100 mA 15mS

CREDIT Open Collector 30V DC 100 mA A Optic 15mS then B

TILT Open Collector 30V DC 100 mA B Optic 15mS then A

INHIBIT CONTROL DISABLE Voltage ENABLE Voltage


Maximum 12V DC 2.0V DC
Active : INH HIGH Minimum 5V DC or Open 0V or Ground

MECHANICAL

Chassis : 06660058 CC/MC Std / 0 Studding : 6A Optic Sensor : None


COIL Config : CC-MC Standard Coil Gap : .125" Token Holder : N/A
Housing : 04660166.150 snap in Lever Weight : 12 Gram Exit Spacer : None

COIN RANGE DIAMETER THICKNESS WEIGHT


Minimum 1.196in / 30.38mm 0.081in / 02.06mm 10.5 Grams

Maximum 1.470in / 37.34mm 0.115in / 02.92mm 11.0 Grams

ENVIROMENTAL Operating TEMP : 0 to 60 Degrees C Storage TEMP : -40 to 80 Degrees C


EMI Note : Meets European ElectroMagnetic Conformity to display the CE Mark,
Standards EN55014, EN55104, TUV License No. V9771840.01

PERFORMANCE Feed Rate : 8 Coins/Sec > 98% Good Coin Acceptance


POT Range : 0 to 1.5 Volts Coin Profile :
Test Coin : U.S. 50 CENT Test Coin # 04091139
Reject Coin : Reject Coin #

All testing is based on a U.S. 50 Cent test coin, with adjustments set to accept all U.S. 50 Cent coins and reject all known slugs. Coins are
dropped from a maximum height of 2" above insert with coins vertically oriented and aligned with the coin entry. Nominal operating voltage. Use
document 09300311 for Comparitor Test Station Instructions.

CMI Mech Database FORM Spec 7Pin R2 Monday, September 08, 2003 11:50 AM

You might also like