NUMBER: 24-007-08 REV.
GROUP: Heating & Air
Conditioning
DATE: October 29, 2008
This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of Chrysler LLC.
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 24-007-08, DATED
AUGUST 9, 2008. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND
INCLUDE AN ADDITIONAL MODEL YEAR.
StarSCAN® SOFTWARE LEVEL MUST BE AT RELEASE 9.03OR HIGHER.
StarMOBILE® DESKTOP CLIENT MAY ALSO BE USED TO PERFORM THIS
PROCEDURE.
SUBJECT:
FLASH: ATC/MTC Poor Performance / Vehicle Not Cooling Enough and/or A/C System
Recovery and Recharge
OVERVIEW:
This bulletin involves reprogramming the Automatic Temperature Control Module (ATC) or
Manual Temperature Control Module (MTC) -AND/OR- performing an A/C system
recovery and recharge with a revised refrigerant level. **2007 Model Year vehicles require
a MTC module replacement.**
MODELS:
**2007** - 2008 (KA) Nitro
2008 (KK) Liberty
SYMPTOM/CONDITION:
Some customers may complain that A/C performance is poor and that the A/C is not
cooling enough or fails to keep the passenger compartment cool. This update will provide
customers with improved A/C performance.
24-007-08 REV. A -2-
DIAGNOSIS:
1. **Is the vehicle a 2007 model year vehicle?
a. Yes >> Replace the Temperature Control Module with PN 55111884AF. Follow the
procedures in TechCONNECT > 24 - Heating & Air Conditioning > Controls >
Control, A/C and Heater > Removal/Installation. Door calibration will be performed
automatically once the new control module detects key on.
b. No >> Proceed to Step #2.**
2. **Is the vehicle build date before May 30, 2008?
a. Yes >> Perform the Flash Repair Procedure and A/C system recovery and
recharge.
b. No >> For vehicles built between May 30, 2008 and before July 2, 2008, perform
Step 7 of the Repair Procedure.**
PARTS REQUIRED:
Qty. Part No. Description
**AR (1)** **55111980AA** **Control Head, MTC**
AR NPN Refrigerant
SPECIAL TOOLS / EQUIPMENT REQUIRED:
NPN Battery Charger
NPN C-4755 Trim Stick
CH9401 StarSCAN® Tool
CH9404D StarSCAN® Vehicle Cable
CH9409 StarSCAN® Documentation Kit
CH9410 StarSCAN® Ethernet Cable, 12 ft.
CH9412 StarSCAN® Software Update Device Kit
TechCONNECT PC or Equivalent
REPAIR PROCEDURE - USING THE INTERNET TO RETRIEVE THE FLASH FILE:
NOTE: When performing this Repair Procedure, the software release level in the
StarSCAN®; must be programmed with 9.03 level software or higher. The
software release level is visible in the blue header at the top of the
StarSCAN® screen.
NOTE: The StarSCAN® diagnostic scan tool fully supports Internet connectivity.
However, to take advantage of this feature you must first configure the
StarSCAN® for your dealership's network. Make sure the StarSCAN® is
configured to the dealership's network before proceeding. For instruction on
setting up your StarSCAN® for the dealer's network refer to either:
“DealerCONNECT > Service > StarSCAN® and StarMOBILE® tools > Online
Documentation”, or refer to the StarSCAN® Quick Start Networking Guide.
The StarSCAN® Quick Start Networking Guide is also available on the
www.dcctools.com website under the "Download Center".
-3- 24-007-08 REV. A
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
NOTE: The repair Procedure (HVAC Control Flash) can be performed using the
StarSCAN and StarMOBILE Standalone and Desktop.
1. Install a battery charger and verify that the charging rate provides approximately 13.5
volts. Set the battery charger to continuous charge. Do not allow the charger to time
out during the flash process. Remove the charger from the battery when the flash
process is complete.
2. Connect the CH9410 StarSCAN® ethernet cable to the StarSCAN® and the dealer's
network drop.
3. Connect the CH9404D StarSCAN® vehicle cable to the StarSCAN® and the vehicle.
4. Power ON the StarSCAN®.
5. Turn the ignition switch on.
6. Retrieve the old HVAC part number. Using the StarSCAN® at the “Home” screen:
a. Select “ECU View”
b. Touch the screen to highlight the HVAC in the list of modules.
c. Select “More Options”
d. Select “ECU Flash”
e. Record the part number at the top of the “Flash HVAC” screen for later reference.
f. Select “Browse for New File”. Follow the on screen instructions.
g. Select “Download to Scantool”.
h. Select “Close” after the download is complete, then select “Back”.
i. Highlight the listed calibration.
j. Select “Update Controller”. Follow on screen instructions.
k. When the update is complete, select “OK”.
l. Verify the part number at the top of the “Flash HVAC” screen has updated to the
new part number.
7. Perform an A/C system recovery and recharge following the procedures outlined in
DealerCONNECT >> Heating and Air Conditioning >> Standard Procedures >> Follow
all CAUTIONS and WARNINGS. **A/C systems on these vehicles were originally
charged with 20 ounces of refrigerant. By performing a system recovery and recharge
with 18 ounces of refrigerant, improved A/C performance can be achieved.**
NOTE: Due to the HVAC programming procedure, a DTC may be set in other
modules (TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so equipped.
Some DTC's may cause the MIL to illuminate. From the “Home” screen select
“System View”. Then select “All DTCs”. Press “Clear All Stored DTCs” if
there are any DTCs shown on the list.
24-007-08 REV. A -4-
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation No: Description Amount
**24-50-10-91** **Module, 2007 Manual Temperature **0.3 Hrs.**
Control (MTC) - Replace (B)**
24-50-09-90 Module, 2008 Automatic/Manual 0.6 Hrs.
Temperature Control (ATC/MTC) -
Reprogram (B)
24-01-10-90 Recovery and Recharge, A/C System - 0.4 Hrs.
2008 ONLY
FAILURE CODE:
ZZ Service Action
