853 new.

qxd 3/15/2004 12:44 PM Page 1

Full Featured Keyless Entry System

with Optional Starter Defeat and Passive Immobilize Feature
SYSTEM MANUAL
STANDARD FEATURES SYSTEM OPERATION
Some of the system’s standard features REMOTE LOCKING
include: To lock the doors press button 1:
• Two 4-button remote transmitters • The horn will beep once. *
• Remote keyless entry • The parking lights will flash once.*
• LED Status indicator • The doors will lock.
• Valet switch • The LED will turn solid for 10 seconds
then start flashing slowly.
OPTIONAL FEATURES • The optional starter defeat will
This system has many optional features that engage.*
may not be compatible with some vehicles, * Optional Feature.
and may require additional parts and/or
labor. Please contact your dealer for more The optional Starter Defeat feature disables
details. the vehicle’s starter until button 2 is pressed,
or until the Emergency Override is
• Flashing Parking Lights performed.
• Starter Defeat If the optional Ignition Trigger feature is
• Illuminated Entry programmed, turning on the ignition before
• Trunk/hatch Release pressing button 2 to unlock the doors will
• Passive Immobilze feature cause the horn to honk and the lights to
• Horn Honk output flash for 30 seconds. Press button 2 to
• Remote Panic feature disarm the ignition trigger and allow the
vehicle to start.
REMOTE TRANSMITTER LAYOUT
REMOTE UNLOCKING
To unlock the doors press button 2.
Button 1 Button 2 • The horn will beep twice.*
• The parking lights will flash twice.*
Button 3 Button 4 • The doors will unlock.
• The dome light will turn on.*
* Optional Feature.

NOTE: If the optional two-step unlock

NOTE:Transmitter cosmetics may differ, but feature is installed, pressing button 2 will
button functions remain the same. unlock only the driver’s door. Press button 2
again to unlock all remaining doors.

1
853 new.qxd 3/15/2004 12:44 PM Page 2

PASSIVE STARTER DEFEAT Turn on the ignition, then press the

If the optional starter defeat is installed, the override/valet switch for two seconds. The
system can be programmed to automatically starter defeat will disengage and the system
disable the starter 45 seconds after turning will enter valet mode.
off the ignition as an extra measure of
security in the event the vehicle is VALET MODE
accidentally left unlocked. During the 45 When the system is placed into valet mode,
second countdown, the LED will flash rapidly the optional starter defeat, ignition trigger,
to indicate the passive starter defeat and passive starter defeat will be disabled.To
sequence has begun. After 45 seconds, the put your system into valet mode, turn the
LED will flash slowly and the vehicle’s starter ignition on and hold the override/valet
will be disabled. switch for 3 seconds. The horn will chirp
once (if installed) and the LED will turn on
IGNITION TRIGGER solid to confirm valet mode. To exit valet
After the system is remotely locked, turning mode, repeat the same procedure. The horn
on the ignition before remotely unlocking will chirp twice and the LED will turn off to
the system activates the optional ignition confirm valet mode exit.
trigger feature (if selected during
installation). The horn will honk and the AUXILIARY OUTPUT
parking lights will flash for 30 seconds. To The auxiliary output may be used to activate
deactivate the feature once triggered, press an optional feature such as trunk release.
button 2 on the transmitter or use the Press and hold button 3 for three seconds to
override procedure (see below). activate.

HORN OUTPUT ILLUMINATED ENTRY

If the optional Horn Honk feature is The optional Illuminated Entry turns on the
connected, the horn will provide dome light when the doors are remotely
confirmation chirps when locking or unlocked. The dome light will remain on for
unlocking the doors, or when the Panic 30 seconds or until the ignition is turned on.
feature is activated.

REMOTE PANIC LED STATUS MODES

If the optional horn honk output is installed, Locked = Slow flash
pressing button 4 for three seconds will Disarmed = Off
trigger the Panic mode.The horn will honk Passive Starter Defeat Warn = Rapid flash
and parking lights will flash for 30 seconds, or Valet Mode = Solid
until button 4 is pressed again.

EMERGENCY OVERRIDE
If the optional starter defeat is installed and
your remote is lost or fails to operate, you
can manually override the starter defeat.

2
853 new.qxd 3/15/2004 12:44 PM Page 3

INSTALLATION INSTRUCTIONS
Before you begin the installation: required. For vehicle’s with independent left
• This product must be installed by qualified and right parking light circuits, the parking
personnel according to these instructions. light wires must be connected using diodes
• Verify with the customer the desired to keep the circuits separate.
location for the program switch and LED. • WIRE - Unlock #87 normally open input
• Always use a multimeter when verifying 10A fuse. (see Door Lock Wiring Diagrams)
vehicle wiring. • BLUE/BLACK WIRE - Unlock #30
common output. (see Door Lock Wiring
Installation Notes: Diagrams)
• Do not install the main unit in the engine • BROWN/BLACK WIRE - Unlock #87A
compartment. normally closed input. (see Door Lock Wiring
• Make all wiring connections to the vehicle Diagrams)
before connecting the main 15-pin • VIOLET/BLACK WIRE - Lock #87
connector harness to the main unit. normally open input 10A fuse. (see Door Lock
• Mount the main unit in a secure area, away Wiring Diagrams)
from vehicle computers and heating/air • GREEN/BLACK WIRE - Lock #30
conditioning ducts. Mount the unit as far common output. (see Door Lock Wiring
away from metal objects as possible to Diagrams)
increase the range of the remote • WHITE/BLACK WIRE - Lock #87A
transmitters. normally closed input. (see Door Lock Wiring
• When running the harness wires through Diagrams)
the vehicle, be careful to run them where • ORANGE WIRE - Armed Output (-)
they cannot be damaged or shorted. Keep 500Ma. The ORANGE wire provides ground
them away from any moving parts or areas of when the unit is armed to activate a starter
high heat. Use rubber or plastic grommets to disable relay. Connect to a relay for starter
protect the harness wires where they pass defeat.. (See Relay Wiring Diagrams)
through holes in metal panels.
• BLACK/YELLOW - Dome light output (-)
Main Harness: 500mA. Connect to a relay to activate the
dome light when the system is unlocked. (See
• BLACK WIRE - Ground input (-). Connect to Relay Wiring Diagrams)
a solid chassis ground that is clean and free
of paint or dirt. • GRAY WIRE - Auxiliary output (-) 500mA.
Connect to a relay for optional trunk release
• RED WIRE - +12V battery input. etc. (See Relay Wiring Diagrams)
• WHITE WIRE - Parking light output (+). • BROWN WIRE - Horn honk output (-)
Connect to the wire that shows +12V when 500mA. Connect to a relay to honk the
the parking lights are on. If the vehicle’s vehicle’s horn. (See Relay Wiring Diagrams)
parking light circuit exceeds 10A, a relay is

3
853 new.qxd 3/15/2004 12:44 PM Page 4

• BLUE/WHITE WIRE - Passenger unlock 3. Press the valet switch the number times
output (-) 500mA. The BLUE/WHITE wire equal to the desired feature.
provides a ground to unlock the passenger • The horn will chirp and lights/LED will
doors when the unlock button on the flash, each time the valet switch is
transmitter is pressed two times. To install pressed.
the two-step unlock feature, the 4. Within 5 seconds, press the transmitter
BLUE/BLACK and BROWN/BLACK wires button corresponding to the desired
must be run directly to the driver’s door operating mode for that feature.
actuator unlock wire and the BLUE/WHITE • The horn will chirp and lights will flash
wire must be connected to a relay to unlock to indicate the setting.
the passenger doors. (see Optional Two-Step
Unlock Diagrams) One chirp/flash = Button 1
• YELLOW WIRE - Ignition input (+). Two chirps/flashes = Button 2
Connect to the main ignition wire that 5. Turn off ignition to save changes.
switches +12V and does not drop out during
cranking. FEATURE DESCRIPTION
1. Ignition Lock/Unlock. Automatically
2-Pin Red Connector: Plug-in connector locks the doors when the ignition is turned
port for LED. Mount LED in an area where on and unlocks when the ignition is turned
it may be easily seen from either side of the off.
vehicle. 2. Door Unlock Pulse. Selects between a
2-Pin Blue Connector: Plug-in connector single or double unlock pulse.
port for program/service switch. Mount 3. Chirp Mode. Selects or bypasses the
program switch in an area that is easily system’s lock’unlock confirmation chirps.
accessible from the driver’s position. 4. Door Lock PulseLength. Selects
between a .75-second or 3-second
PROGRAMMABLE FEATURES
lock/unlock pulse.
To enter program mode: 5. Passive Starter Defeat. Enables the
1. Turn on ignition. starter defeat to automatically activate 45
2. Within 5 seconds, press valet switch 5 seconds after turning off the ignition.
times. 6. Ignition Trigger. Enables the ignition
• The horn will provide a long chirp, to trigger feature when the system is remotely
indicate entering program mode. locked.

Remote Programmable Features:

Step Function Button 1 (Default) Button 2
1. Ignition Controlled Door Locks On Off
2. Door Unlock Pulse Single Double
3. Chirp Mode Standard Silent
4. Door Lock Pulse Length .75 Seconds 3 Seconds
5. Passive Starter Defeat Enable Off On
6. Ignition Trigger Feature Off On

4
853 new.qxd 3/15/2004 12:44 PM Page 5

DEFAULT RESET To enter Code Learning Mode:

To reset all programmable features to their 1. Turn ignition key on, off, on, off, on and
factory default settings: leave on within 5 seconds.The horn will
chirp (if installed) and the LED / parking
1. Turn on ignition. lights will flash once.
2. Within 5 seconds, press valet switch 5 2. Press and hold valet switch for 3
times. seconds.The horn will chirp and the LED
• The horn will provide a long chirp, to / parking lights will flash 3 times.
indicate entering program mode. 3. Release the program switch.
3. Press transmitter button 3.The LED will 4. Program all desired remotes by pressing
flash 3 times, pause then continue button 1 on each of the transmitters.
flashing. All programmable features will The parking lights will flash after the
be reset to the default position. system has learned each remote control.
5. Turn ignition key off. Remotes are now
ADDING / DELETING REMOTE programmed to the system.
TRANSMITTERS
Adding new transmitters to the system will
automatically delete all other remotes that
were previously operating the system.
NOTE: You must code all desired remotes
at this time.The unit can learn a maximum of
three transmitters.

5
853 new.qxd 3/15/2004 12:44 PM Page 6

DOOR LOCK WIRING DIAGRAMS

NEGATIVE PULSE DOOR LOCK SYSTEM POSITIVE PULSE DOOR LOCK SYSTEM
(-) DOOR LOCK (+) DOOR LOCK
FACTORY FACTORY FACTORY FACTORY
DOOR LOCK (-) DOOR UNLOCK DOOR LOCK DOOR LOCK (+) DOOR UNLOCK DOOR LOCK
SWITCH RELAYS SWITCH RELAYS

VIOLET VIOLET
BLUE/BLACK BLUE/BLACK
HARNESS

HARNESS
BROWN/BLACK BROWN/BLACK
VIOLET/BLACK VIOLET/BLACK
GREEN/BLACK GREEN/BLACK
NOT USED NOT USED
WHITE/BLACK WHITE/BLACK
NOT USED NOT USED

CONNECT
TO +12V

ADDING ACTUATORS VACUUM DOOR LOCK SYSTEM

CONNECT VACUUM PUMP
TO +12V

VIOLET VIOLET
BLUE/BLACK BLUE/BLACK
HARNESS
HARNESS

BROWN/BLACK BROWN/BLACK
VIOLET/BLACK
GREEN/BLACK
VIOLET/BLACK
GREEN/BLACK XCUT

WHITE/BLACK WHITE/BLACK
L
CONNECT AFTER-MARKET
TO +12V ACTUATORS UL

LOCK/UNLOCK
SWITCH

REVERSE POLARITY DOOR LOCK SYSTEM

CONNECT
TO +12V L

UL

VIOLET
BLUE/BLACK
X CUT LOCK/UNLOCK
SWITCH
HARNESS

BROWN/BLACK
VIOLET/BLACK
GREEN/BLACK
WHITE/BLACK

CUT
X FACTORY DOOR
MOTOR

6
853 new.qxd 3/15/2004 12:44 PM Page 7

OPTIONAL TWO-STEP UNLOCK WIRING DIAGRAMS

TWO-STEP UNLOCK TWO-STEP UNLOCK
NEGATIVE PULSE POSITIVE PULSE

CONNECT
(-) DOOR LOCK
L TO +12V
(+) DOOR LOCK
(-) DOOR UNLOCK 87 L
UL (+) DOOR UNLOCK
BLUE/WHITE BLUE/WHITE 87a UL
86 85
LOCK/UNLOCK 30
CONNECT SWITCH
TO +12V LOCK/UNLOCK
CONNECT SWITCH
FACTORY DOOR TO +12V
VIOLET
BLUE/BLACK LOCK MODULE VIOLET FACTORY DOOR
LOCK MODULE
HARNESS

BROWN/BLACK BLUE/BLACK

HARNESS
VIOLET/BLACK BROWN/BLACK
GREEN/BLACK CUT
X VIOLET/BLACK
WHITE/BLACK GREEN/BLACK CUT
X
WHITE/BLACK

DRIVER'S DOOR PASSENGER DOOR

MOTOR MOTORS DRIVER'S DOOR PASSENGER DOOR
MOTOR MOTORS

TWO-STEP UNLOCK TWO-STEP UNLOCK

REVERSE POLARITY ADDING ACTUATORS

CONNECT L CONNECT PASSENGER DOOR

TO +12V TO +12V ACTUATORS
UL
87 86 87 85
87a
BLUE/WHITE
86
87a
85
XCUT LOCK/UNLOCK
SWITCH
BLUE/WHITE

30 30

X
CUT PASSENGER DOOR
MOTORS
VIOLET
BLUE/BLACK
HARNESS

BROWN/BLACK
CONNECT VIOLET/BLACK
TO +12V GREEN/BLACK
WHITE/BLACK
VIOLET
BLUE/BLACK DRIVER'S DOOR
HARNESS

BROWN/BLACK ACTUATOR
VIOLET/BLACK
X
CONNECT
CUT
GREEN/BLACK TO +12V
WHITE/BLACK DRIVER'S DOOR
MOTOR

7
853 new.qxd 3/15/2004 12:44 PM Page 8

KEYLESS ENTRY WIRING DIAGRAM

Valet Switch

LED

Black Ground (-)

Red +12V Battery input (+) [15A fuse]
White Parking Light output (+) [10A fuse]
Violet Unlock #87 Normally Open input [10A fuse]
Blue/Black Unlock #30 Common output
Brown/Black Unlock #87a Normally Closed output
Violet/Black Lock #87 Normally Open input [10A fuse]
Green/Black Lock #30 Common output
White/Black Lock #87a Normally Closed output
Orange Starter Defeat output (-) 500mA
Black/Yellow Dome Light output (-) 500mA
Gray Auxiliary output (-) 500mA
Brown/White Horn Honk output (-) 500mA
Blue/White Passenger Unlock Output (-) 500mA
Yellow Ignition input (+)

RELAY WIRING DIAGRAMS

STARTER DEFEAT TRUNK RELEASE DIAGRAM
TO TRUNK RELEASE WIRE
CONNECT
TO +12V
87 IGNITION 87
ORANGE
WIRE
86
87a
85
X CUT
SWITCH GRAY
WIRE 87a
86 85
30 30
TO
STARTER
CONNECT
TO +12V

HORN HONK / DOME LIGHT DIAGRAMS

TO POSITIVE HORN HONK TO POSITIVE HORN HONK
OR DOME LIGHT WIRE OR DOME LIGHT WIRE

87 87
HORN OR DOME CONNECT HORN OR DOME
LIGHT OUTPUT 87a LIGHT OUTPUT
TO +12V 87a
FROM ALARM 86 85 FROM ALARM 86 85
30 30

CONNECT
TO +12V

© 2004 64-853 Rev 1 2/04