FCC ID : O44J1WENR

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance could void the user s authority to
operate this device.

USER’S GUIDE

Downloaded from www.Manualslib.com manuals search engine

 User’s GUIDE
User’s GUIDE TABLE OF CONTENTS
Safety Information Page 4
Remote : Page 4
Remote Button Functions Page 5
Remote Learning Routine Page 5
Keyless Entry Page 6
Alarm Mode Page 6
Trunk Release Page 7
Panic Mode Page 7
Valet Mode Page 7
Optional Programmable Features Page 8
Ignition Lock Page 8
Passive Locking Page 8
Optional Installation Features Page 8
Door pulse Duration Page 8
Flashing Signal Light Page 8
Anti-jacking Page 8

Page 3

Downloaded from www.Manualslib.com manuals search engine

 Safety Information Remote Button Functions
Please take these safety precautions into consideration, under the following conditions : Button Press Function
1 0.5 sec Lock
When servicing your automobile (i.e. changing the oil, washing your car), the
Magicar system should be in Valet Mode. 2 0.5 sec Unlock
3 0.5 sec Siren Chirps for Lock /Unlock - on/off
Whenever you loan your vehicle to an individual who is not familiar with Magicar, 4 0.5 sec Valet Mode - on/off
please put the vehicle in Valet mode. This will prevent the vehicle barrower from
5 2 sec Panic, Press Lock to shut off Siren
accidentally activating the Magicar auto-security system.
6 0.5 sec Ignition Lock - on/off
Remote
7 0.5 sec Passive Arming - on/off
The model name, R500 stands for 8 0.5 sec Shock Sensor - on/off
9 2 sec Trunk Release
10 2 sec Programming Menu - Installer Only

Means pressing the button for 2 seconds.

Means simultaneously pressing the buttons.
Means simultaneously pressing the buttons for 2 seconds.

Remote Learning Routine

The Magicar will allow up to three remotes to be programmed to one vehicle.
Please perform the following procedure to add or reprogram additional remotes.

Activate Valet/ Programming mode by manually

turning the ignition on and off three times
with the key within a 7 second period.
The parking lights will flash once with successful completion of
this step.

Page 4 Page 5

Downloaded from www.Manualslib.com manuals search engine

 Within a 7 second period after cycling the ignition for the 3rd time, Trunk Release
Press the button for a 0.5 second. The parking lights will flash
Press the button for 2 seconds, in order to unlock and release your trunk door.
once to confirm that the transmitter has been programmed.
If pressing the trunk release button does not release the trunk, you will need to
You can continue programming additional remotes. The parking lights
will flash two times when the programming mode has expired.
release the button and try again, as the remote stops transmitting as soon as the
LED stops flashing.Note that the trunk release function will not only release the trunk
Keyless Entry but will unlock the all doors as well.

To lock the vehicle, pressing the button for a 0.5 second.

To unlock the vehicle, press the button for a 0.5 second. If the pressing of the Panic Mode
lock/unlock buttons does not lock/unlock the doors, you will need to release the
Press the button for 2 seconds to enter Panic Mode. In this mode, the car will be
button and try again, as the remote stops transmitting as soon as the LED stops
flashing. If the button is pressed for 2 seconds, it will panic the system. armed,if not armed already, and the siren will be activated and the parking lights will be
flashed. In order to disengage Panic Mode, press the button.
Then, press the button for a 0.5 second to unlock/ disarm your vehicle.
Alarm Mode
If Anti-Jacking option has been programmed (ask your dealer if you would
To arm the vehicle, press the button . like to have this option) and the Ignition-Kill has been installed , Panic
To disarm the vehicle, press the button. Mode works as Anti-Jacking if the car key in the ignition. In Anti-Jacking
If pressing the arm/disarm buttons does not arm/disarm the vehicle, you will need to mode is activated while key is in the ignition,
release the button and try again, as the remote stops transmitting as soon as the
a) the Siren will go off for 1.5 minutes, and b) Ignition-Kill will be activated
LED stops flashing.
after the first 30 seconds. This is to give a 30 second warning to the
Press the buttons for a 0.5 second to mute the vehicle siren when
hijacker, then to disconnect the ignition to stop the vehicle.
arming or disarming your vehicle. Keep in mind that your siren will still be activated
for all other modes(i.e.panic or alarm trigger) regardless of whether or not your siren
is in mute mode. The siren will be mute only when arming or disarming your vehicle. Valet Mode
When the alarm is armed, the starter kill function (an optional feature provided by While the vehicle is in valet mode, the only feature is the keyless entry and optional auxiliary
your installer) is activated. This feature disengages the starter mechanism on your functions.
vehicle and prevents it from starting, even with a key. In order to enter Valet mode, press the buttons simultaneously for a 0.5 sec-
ond. In order to manually enter Valet Mode, insert your car key into the ignition and turn the
ignition on and off three times within 7 seconds
If you lose your remote after you have armed the vehicle, use your key
to open the door. The siren will go off. Turn the ignition on and off,
You can exit Valet Mode only by pressing buttons
3 times with your key to shut down the alarm and put the system into
simultaneously.
valet mode. You can cancel valet mode with a remote later on.
See: Valet mode, on page 7.

Page 6 Page 7

Downloaded from www.Manualslib.com manuals search engine

 OPTIONAL PROGRAMMABLE FEATURES
These additional features may be programmed to the Magicar system by your
authorized Magicar dealer.

Ignition Lock
INSTALLATION GUIDE
This programmable option enables your vehicle to automatically lock the doors once
the key is in the ignition for 30 Seconds.(Also you can lock the doors, If you step on INSTALLATION GUIDE TABLE OF CONTENTS
the brake pedal within 30 Seconds) In addition, the vehicle will automatically unlock
Installation Tips & Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10
the doors when the key is pulled out of the ignition.
R500 Wiring Digram . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11
Passive Locking CON 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12
You can turn this function on or off by pressing the buttons for a 0.5 sec- CON 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 13
ond. When setting to passive locking, your system will lock automatically 30 seconds CON 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 14
after all the car doors are closed. CON 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16
CON 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16
OPTIONAL INSTALLATION FEATURES Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16
if you set this mode, Door Lock/Unlock
Option Mode . . . . . . . . . .. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . .. . . . . . . . Page 17
Pulse Duration will be changed 0.8 second to 4 seconds.
It can be programmed to send a signal to a relay to disconnect Programming Menu Option . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . Page 17
the ignition wire of the vehicle upon anytime the vehicle is armed so that the How to set Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18
vehicle cannot start or run by a remote or a key. Canceling(Going to Factory Default)Option Mode . . . . . . . . . . . . . . . Page 19
And the running of vehicle can be shut off by remote’s panic command.
Confirmation of Wrong Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19
It can be programmed to send a signal to a relay to disconnect the
starter wire of the vehicle upon arming.
When you leave your car without
closing the doors, the signal lights will flash.

Page 8 Page 9

Downloaded from www.Manualslib.com manuals search engine

 Installation Tips & Recommendations
1-1. Please be careful not to lock yourself out.
1-5. Vehicle check-up prior to and after the installation.
Please lower the glass windows before you start the installation in case the door locks
with the key inside. Also, learn the remote to the brain module after the installation
has been completed.
1-2. Use Digital Multimeter for testing
Use a Digital Multimeter for all testing of wires in the vehicle. This should be done
on all wires even if you feel that you know exactly what they are and how they M861A Wiring Digram
should test. Use of lamp tester may damage the electrical circuit of the vehicle.
1-3. Find Good Ground
One of the most important wire connections is the ground connection.
Please find a spot that does not have any resistance to the battery ground.
Improper ground will result in malfunction of the system.
1-4. Make sure your installation does not become a driving hazard later
to the driver.
During installation process, please try to foresee there are any potential problems
to the driver later.

Antenna

Page 10 Page 11

Downloaded from www.Manualslib.com manuals search engine

 C0N1 C0N2
No 1 (Red) : (+)12V Input
Solder this wire to the vehicle’s 12V constant. This wire must be supplied power all
of the time and must be able to withstand high current draw.
No 2 (Green/ White) : (+)Output for parking Light
Positive parking light output.

No 3 (Brown) : (+)12V Siren Output

The Black wire at the siren is to be chassis grounded. < Circuit diagram > Circuit diagram during unlock output >
The siren volume can be reduced by cutting the volume wire attached to the siren.
Installers are able to install as per
No 4 (Gray) : (+)12V Trunk Output the following methods when you install,
If the vehicle is equipped with electrical trunk release, the trunk out is please find a suitable method as per
connected to trigger the trunk solenoid. the door system of your vehicle

trunk Circuit diagram during lock output>

Solenoid
trunk Release Switch

CON1-4

Negative Trigger Door Lock System

No 5 (Black) : Chassis Ground
(W/O Actuator)
This will be the one of the most important connections. Connect this wire to bare
metal of the vehicle. We do not recommend using the steering column for a ground-
ing point. Make sure you strip back the paint or use a factory grounding point.
Bad grounding on this wire will be the beginning of future troubles.

Positive Trigger Door Lock System

(W/O Actuator)

Page 12 Page 13

Downloaded from www.Manualslib.com manuals search engine

 External Actuator
No 3 (Red/Black) : Negative Trigger Door Open Sense
No 4 (Red) : Positive Trigger Door Open Sense
Dome Light Dome Light

Door Door
Trigger SW Trigger SW
+12V +12V

CON3-3(-) Door Trigger CON3-4(+) Door Trigger

< External Actuator>
Please make sure you have found a correct door sensing wire that monitors all doors.

C0N3
No 5 (Violet / Black ) : (-)Trunk Trigger Input.
No 1 (Green) : (+12V)Ignition Input
connect this to wire to the trunk lamp wire as shown below
This wire will test (using your digital multi-meter) 0V with the key off, and 12V with
the key in the ON or RUN position

No 2 (Blue) : Negative Starter-Kill Output Trunk Lamp

+12V
Please use the pre-wired starter kill relay.
CON 3-5
(-)Trunk Trigger Input

C ON ON
C
AC Key Cylinder AC Key Cylinder No6 (Light Blue / White) : (+) Brake Trigger Input
START

START
OFF

OFF

Connect this wire to the foot Brake Wire as shown below.

Relay
Relay Stop Lamp
85 Starter Wire Ignition Wire
85
87 87a Cut 87 87a Cut Foot Brake S/W

86 30 +12V
86 30
Engine CON3-6(+)Brake Trigger
Starter

Page 14 Page 15

Downloaded from www.Manualslib.com manuals search engine

 No7 (Black /White) : (-) Input for optional Sensor Options Mode
When installing additional sensors, use this wire as the input wire for those sensors. Press buttons and Simultaneously for 2 seconds in order to enter
Always remember, when attaching more than one sensor to any input, you must diode iso-
Option Mode.
late them so that they don’t backfeed into each other.
Features (Factory Default)
C0N4
Door Lock/Unlock Pulse Duration 0.8 Sec 4 Sec

No 1 (Black) : GND Application of Pre-wired Kill Relay Starter Kill Anti-jacking (IG-kill)
LED Ass y
No 2 (Black/White) : (+)LED Flashing Parking Light During Door Open Disabled Activated

C0N 5
Programming Menu Option
No 1 (Black) : GND
No 2 (White) : (-)and stage shock Input
Note :
"1. Door Lock/Unlock Pulse Duration :
No 3 (Red) : (+12) Dual stage shock sensor
If you set this mode, Door Lock/Unlock Pulse Duration wil be changed 0.8 second
No 4 (Yellow) :(-)1st stage shock Input to 4 seconds.

2. Start Kill Mode

Antenna Anti-Jacking(Ignition-Kill) :
The #2 wire of CON3 can be programmed to send a signal to a relay to disconnect
When Magicar systems are installed, please pay attention to stretch out the wire of the ignition wire of the vehicle anytime the vehicle is armed so that the vehicle cannot
antenna. If the wire is bended or twisted seriously, it will be one of the reasons, start or run by remote or key. The vehicle can also be shut off with remote by use of
the panic command, even if it is running with a key in the ignition.
which will reduce the receiving range.
Srarter-Kill :
The #2 wire of CON3 can be programmed to send a signal to a relay to disconnect
Antenna Module the srarter wire of the vehicle upon arming.
FCC ID: O44J1WAMLEDANT
3. Parking Light Flashing :
With this option, the parking lights will flash if any door remains open while the vehi-
cle is disarmed.

Page 16 Page 17

Downloaded from www.Manualslib.com manuals search engine

 How to set Options Canceling (Going to factory default) Option Mode
You can only program one option at a time. You will have to repeat the procedure for Press buttons + for 2 seconds (The siren and signal lights will
every option you would like to change. chirp and flash one time each).
Press buttons + for 2 seconds. The siren and signal lights - If you fail to program, the siren and lights will chirp and flash three
will chirp and flash one time each. times each.
- If you fail to program, the siren and signal lights will chirp and flash Press button three times. (The siren and signal lights will chirp and
three times each. flash once time the button is pressed.)

Press button the number of times to go to the option number you All options will be reset to factory defaults after the confirming 3 chirps
want to change. and flashes.
- The siren and signal lights will chirp and flash one time whenever
you press button . Confirmation of Wrong Programming
Wait a few seconds. You will hear a number of chirps and see a number When you press the buttons incorrectly, Option Mode will not be programmed
of parking light flashes corresponding to the option number you want and the siren will activate for 1 second.
to change. If the number of chirps or flashes does not match the option
number you want, wait 10 seconds, then start over at step 1.
Press button or as you want to program the option.
- If you press button , the option will be set to the default setting.
The siren and signal lights will chirp and flash one time each.
- If you press button , the option will be set to the optional setting.
The siren and signal lights will chirp and flash two times each.

Press button + for 2 seconds (The siren and signal lights will chirp
one time each)
Press button three times (The siren and signal lights will chirp and flash
one time whenever press button ) and wait for 5 seconds.
The siren and signal lights will chirp and flash three times after 5 seconds
Press button after confirmation of the siren and signal lights as no. 3
(The siren and signal lights will chirp and flash two times each.)

Page 18 Page 19

Downloaded from www.Manualslib.com manuals search engine