HCD-CPZ1DAB

SERVICE MANUAL UK Model

Ver. 1.1 2006.10

• HCD-CPZ1DAB is the amplifier, CD player, tape

deck and tuner section in CMT-CPZ1DAB.

US and foreign patents licensed from Dolby

Model Name Using Similar Mechanism NEW
Laboratories.
CD CD Mechanism Type CDM80BH-K6BD83S-WD
Section Base Unit Name BU-K6BD83S-WD
Optical Pick-up Block Name KSM-213DCP
TAPE Model Name Using Similar Mechanism HCD-CPZ1
Section Tape Transport Mechanism Type CMAL1Z255A

SPECIFICATIONS

Main unit FM stereo, FM/AM superheterodyne tuner

FM tuner section: Frequency Label Frequency Label
Amplier section Tuning range: 87.5 – 108.0 MHz (50 kHz step) 190.640 MHz 7B 225.648 MHz 12B
DIN power ou tput (ra ted): 60 + 60 W (4 ohms at 1 kHz, DIN) Antenna: FM lead antenna
Continuous RMS power output (reference): 75 + 75 W (4 ohms at 1 kHz, 10% 192.352 MHz 7C 227.360 MHz 12C
Antenna terminals: 75 ohms unbalanced
THD) Intermediate frequency: 10.7 MHz 194.064 MHz 7D 229.072 MHz 12D
Outputs
CD DIGITAL OUT: Optical Wavelength: 660 nm AM tuner section: 195.936 MHz 8A 230.784 MHz 13A
PHONES (stereo mini jack): Accepts headphones with an impedance of 8 Tuning range: 531 − 1,602 kHz (with the tuning interval set at 9 kHz) 197.648 MHz 8B 232.496 MHz 13B
ohms or more Antenna: AM loop antenna
Antenna terminals: External antenna terminal 199.360 MHz 8C 234.208 MHz 13C
SPEAKER: Accepts impedance of 4 ohms
Intermediate frequency: 450 kHz 201.072 MHz 8D 235.776 MHz 13D
CD player section
System: Compact disc and digital audio system DAB frequency table (Band-III) 202.928 MHz 9A 237.488 MHz 13E
Laser Diode Properties 204.640 MHz 9B 239.200 MHz 13F
Emission Duration: Continuous Frequency Label Frequency Label
206.352 MHz 9C
Laser Output*: Less than 44.6µW 174.928 MHz 5A 209.936 MHz 10A
* This output is the value measurement at a distance of 200 mm from the 208.064 MHz 9D
objective lens surface on the Optical Pick-up Block with 7 mm aperture. 176.640 MHz 5B 211.648 MHz 10B
Frequency response: 20 Hz – 20 kHz (±1 dB) 178.352 MHz 5C 213.360 MHz 10C General
Wavelength: 770 – 810 nm Power requirements: 230 V AC, 50/60 Hz
180.064 MHz 5D 215.072 MHz 10D Power consumption: 60 watts
Tape deck section Dimensions (w/h/d) (excl. speakers): Approx. 175 × 240 × 300 mm
181.936 MHz 6A 216.928 MHz 11A
Recording system: 4-track 2-channel, stereo Mass (excl. speakers): Approx. 3.9 kg
Tuner section 183.648 MHz 6B 218.640 MHz 11B
DAB tuner section: 185.360 MHz 6C 220.352 MHz 11C Design and specications are subject to change without notice.
Frequency range
Band-III: 174.928 (5A) – 239.200 (13F) MHz 187.072 MHz 6D 222.064 MHz 11D
* For details, see “DAB frequency table” below. 188.928 MHz 7A 223.936 MHz 12A
Antenna: FM/DAB lead antenna
Antenna terminal: 75 ohms, F female

COMPACT DISC DECK RECEIVER

9-887-335-02 Sony Corporation
2006J05-1 Personal Audio Division
© 2006.10 Published by Sony Techno Create Corporation
HCD-CPZ1DAB

TABLE OF CONTENTS

1. SERVICING NOTES ............................................... 4 7-25. Schematic Diagram – JACK Section – ............................ 43

7-26. Printed Wiring Board – SW POWER Board – ................ 44
2. GENERAL ................................................................... 5 7-27. Schematic Diagram – SW POWER Board – ................... 45
7-28. Printed Wiring Board – SUB POWER Board – .............. 46
3. DISASSEMBLY 7-29. Schematic Diagram – SUB POWER Board – ................. 47
3-1. Disassembly Flow ........................................................... 6
3-2. Case ................................................................................. 7
3-3. Front Panel Section ......................................................... 7 8. EXPLODED VIEWS
3-4. TC Board, Mechanical Deck (CMAL1Z255A) .............. 8 8-1. Case Section .................................................................... 60
3-5. PANEL Board .................................................................. 8 8-2. Mechanical Deck (Tape) Section ..................................... 61
3-6. MAIN Board .................................................................... 9 8-3. Front Panel Section ......................................................... 62
3-7. CD Mechanism Deck (CDM80BH-K6BD83S-WD) ...... 9 8-4. Lid (TC) Section .............................................................. 63
3-8. DAB Module Assy .......................................................... 10 8-5. Chassis Section ................................................................ 64
3-9. Chassis (Top) ................................................................... 10 8-6. AMP/Power Section ........................................................ 65
3-10. Lever (Loading-L/R) ....................................................... 11 8-7. CD Mechanism Deck Section-1
3-11. Lever (Disc Sensor), Lever (Disc Stop) .......................... 12 (CDM80BH-K6BD83S-WD) .......................................... 66
3-12. DRIVER Board, 8-8. CD Mechanism Deck Section-2
Motor (Pulley) Assy (Loading) (M701) .......................... 12 (CDM80BH-K6BD83S-WD) .......................................... 67
3-13. CD Board ......................................................................... 13 8-9. CD Mechanism Deck Section-3
3-14. BU Section ...................................................................... 13 (CDM80BH-K6BD83S-WD) .......................................... 68
3-15. Optical Pick-up Block (KSM-213DCP) .......................... 14 8-10. Base Unit Section (BU-K6BD83S-WD) ......................... 69
3-16. Lever (BU Lock) ............................................................. 14
3-17. Close Lever ...................................................................... 15 9. ELECTRICAL PARTS LIST ................................ 70
3-18. Lever (DIR), Gear (IDL-B) ............................................. 15
3-19. Gear (IDL-C) ................................................................... 16

4. TEST MODE .............................................................. 17

5. MECHANICAL ADJUSTMENTS ....................... 19

6. ELECTRICAL ADJUSTMENTS ......................... 19

7. DIAGRAMS Notes on chip component replacement

7-1. Block Diagram • Never reuse a disconnected chip component.
– CD SERVO/TAPE DECK Section – ............................ 20 • Notice that the minus side of a tantalum capacitor may be
7-2. Block Diagram – MAIN Section – .................................. 21 damaged by heat.
7-3. Block Diagram
– PANEL/KEY/POWER SUPPLY Section – .................. 22 Flexible Circuit Board Repairing
7-4. Printed Wiring Board – CD Board – ............................... 24 • Keep the temperature of the soldering iron around 270 ˚C
7-5. Schematic Diagram – CD Board – .................................. 25 during repairing.
7-6. Printed Wiring Board – TC Board – ................................ 26 • Do not touch the soldering iron on the same conductor of the
7-7. Schematic Diagram – TC Board – .................................. 27 circuit board (within 3 times).
7-8. Printed Wiring Board – DAB Board – ............................. 28 • Be careful not to apply force on the conductor when soldering
7-9. Schematic Diagram – DAB Board – ............................... 29 or unsoldering.
7-10. Printed Wiring Board – DRIVER Board – ...................... 30
7-11. Schematic Diagram – DRIVER Board – ......................... 30
CAUTION
7-12. Printed Wiring Board – MAIN Board – .......................... 31
Use of controls or adjustments or performance of procedures
7-13. Schematic Diagram – MAIN Board (1/2) – .................... 32
other than those specified herein may result in hazardous radiation
7-14. Schematic Diagram – MAIN Board (2/2) – .................... 33
exposure.
7-15. Schematic Diagram – AMP Board (1/2) – ...................... 34
7-16. Schematic Diagram – AMP Board (2/2) – ...................... 35
7-17. Printed Wiring Board – AMP Board – ............................ 36 This appliance is classified as
7-18. Printed Wiring Board – SP Board – ................................ 37 a CLASS 1 LASER product.
7-19. Schematic Diagram – SP Board – ................................... 37 The CLASS 1 LASER
7-20. Printed Wiring Board – LCD Board – ............................. 38 PRODUCT MARKING is
7-21. Schematic Diagram – LCD Board – ................................ 39 located on the rear exterior.
7-22. Printed Wiring Boards – PANEL Section – ..................... 40
7-23. Schematic Diagram – PANEL Section – ......................... 41
7-24. Printed Wiring Boards – JACK Section – ....................... 42 SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

2
 HCD-CPZ1DAB
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

3
HCD-CPZ1DAB
SECTION 2 This section is extracted from
GENERAL instruction manual.

Basic Operations
Notes Notes on loading discs
To Press
• If your country or region does not support DAB broadcast, “No • When you turn on the system, the disc is not pulled into the disc slot
Service” appears. until “No Disc” appears in the display. Do not attempt to push in the Pause playback X (pause) e; on the remote (or
• Do not press any button on the unit or the remote during DAB disc until “No Disc” appears. TAPE X (pause) e; on the unit).
Automatic Scan. Scanning is interrupted and service list may not be • If you load a disc that is not playable by this system, it will be ejected To resume play, press the button
created properly. In this case, run the DAB Automatic Scan again. automatically.
• If you move to another area, repeat this procedure to store the • Do not load an 8 cm disc with an adaptor. Doing so may cause the again.
stations for your new area. system to malfunction. Stop playback x (stop) qk on the remote (or
• This procedure clears all previously stored presets. • When you remove a disc, handle the disc by its edge and pull it
TAPE x (stop) 9 on the unit).
• Before unplugging the DAB antenna, make sure the system is turned straight out of the disc slot. Do not touch the surface.
off to preserve your own DAB settings.
Note on the jog dial Rewind or fast m/M (rewind/fast forward) qa.
• This tuner does not support data services.
Only the first 9 characters are displayed when performing the group forward
search, track search, or file search.

Notes on Repeat Play Tip

If you select “j” the tape deck stops automatically aer repeating
Selecting a music source • All tracks or les on a disc are played repeatedly up to five times.
• “REP 1” indicates that a single track or file is repeated until you stop
the sequence ve times.
Press the following buttons (or press FUNCTION 8 it.
repeatedly). Notes on playing MP3 discs
To select Press • Do not save other types of les or unnecessary groups on a disc that
has MP3 fies.
Changing the display
CD CD qh on the remote. • Groups that have no MP3 les are skipped.
• MP3 les are played back in the order that they are recorded onto To change Press
Tuner TUNER/BAND q;. the disc. Information on DISPLAY 4, repeatedly when the
DAB DAB wj on the remote. • The system can only play MP3 les that have a le extension of
“.MP3.”
the display* system is on.
Tape TAPE 9 on the remote. • If there are les on the disc that have the “.MP3” file extension, Display mode DISPLAY 4, repeatedly when the
but that are not MP3 les, the unit may produce noise or may (See below.)
Component (connected FUNCTION 8 repeatedly malfunction.
system is off.
using an audio cord) until “MD” appears. • The maximum number of: *For example, you can view:
– groups is 256 (including the root folder). –CD/MP3 disc information such as the track or le number, group
– MP3 les is 511. name (during normal play), or the total play time (while the player
– MP3 les and groups that can be contained on a single disc is 512. is stopped)
– directory levels (the tree structure of les) is 8. –DAB station information such as the service name, channel label,
Adjusting the sound • Compatibility with all MP3 encoding/writing soware, recording preset number, frequency, DLS (Dynamic Label Segment), or
device, and recording media cannot be guaranteed. Incompatible ensemble label
MP3 discs may produce noise or interrupted audio or may not play
To adjust the volume at all. The system oers the following display modes.
Press V O LUME +/– on the remote (or turn the
Notes on playing multisession discs Display mode When the system is off,1)
VOLUME control on the unit) qj.
• If the disc begins with a CD-DA (or MP3) session, it is recognized as Clock The clock is displayed.
a CD-DA (or MP3) disc, and other sessions are not played back.
To add a sound effect • A disc with a mixed CD format is recognized as a CD-DA (audio) Power Saving The display is turned off to conserve
To Press disc. Mode2) power. e timer and clock continue
to operate.
Generate a more DSGX wf on the unit.
1)
dynamic sound The STANDBY indicator lights up when the system is off.
2)
(Dynamic Sound Listening to the radio When the system is in Power Saving Mode, the following functions
are unavailable:
Generator X-tra) –setting the clock.
Before you can receive DAB, you must complete the
Set the sound effect EQ wd on the remote –changing the CD power manage function.
DAB Automatic Scan procedure (see “Before using the
repeatedly to select “BASS” system”). Notes on the display information
or “TREBLE,” and then • The following are not displayed;
press +/– qa on the remote 1 Select “DAB,” “FM” or “AM.” – total playing time for a CD-DA disc depending on the play mode.
repeatedly(orturntheBASS Press TUNER/BAND q; repeatedly. You can also – total playing time for an MP3 disc.
or TREBLE control wd on the select DAB directly by pressing DAB wj on the – remaining playing time for an MP3 file.
• The following are not displayed correctly;
Before using the system unit) to adjust the level. remote.
– elapsed playing time of an MP3 le encoded using a VBR (variable
2 Select the tuning mode. bit rate).
– group and le names that do not follow either the ISO9660 Level
To use the remote Press TUNING MODE 5 repeatedly until “AUTO”
1, Level 2 or Joliet in the expansion format.
Slide and remove the battery compartment lid wk, and appears. • The following are displayed;
insert the two supplied R6 (size AA) batteries, E side Playing a CD/MP3 disc 3 Tune in the desired station. – ID3 tag information for MP3 les when ID3 version 1 and version
first, matching the polarities shown below. 2 tags are used.
1 Select the CD function. Press +/– on the remote (or TUNING +/– on the – up to 124 characters of ID3 tag information using uppercase
Press CD qh on the remote. unit) qa. Scanning stops automatically when a station letters (A to Z), lower-case letters (a to z), numbers (0 to 9), and
is tuned in, and then “TUNED” and “STEREO” (for symbols (! " # $ % & ’ ( ) * + , – . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~).
2 Load a disc. stereo programs) appear. – up to 16 characters of service name, up to 128 characters of DLS
Inserta disc inthe disc slot ws with the label sideup. (Dynamic Label Segment) and up to 16 characters of ensemble
label using uppercase letters (A to Z), lower-case letters (a to z),
numbers (0 to 9), and symbols (! " # $ % & ’ ( ) * + , – . / : ; < = > ?
@[ \ ] ^ _ ` { | } ~).

When you tune in a DAB station or an FM station that

Notes on using the remote
• With normal use, the batteries should last for about six months. provides RDS services, the service name or station Using optional audio components
• Do not mix an old battery with a new one or mix dierent types of name appears on the display.
batteries. To connect an optional headphones
• If you do not use the remote for a long period of time, remove the To stop automatic scanning (FM/AM bands Connect headphones to the PHONES jack ql on the
batteries to avoid damage from battery leakage and corrosion. only) unit.
Press x (stop) qk on the remote.
To set the clock 3 Start playback. To connect an optional analog component
1 Turn on the system. Press N (play) e; on the remote (or CD u (play/ To tune in a station with a weak signal (FM/AM Connect additional analog component to the ANALOG
Press I/1 (power) 1. pause) qh on the unit). bands only) IN jack w; on the unit using an audio analog cord (not
If “TUNED” does not appear and the scanning does not supplied). Turn down the volume on the system, and
2 Select the clock set mode
.
To Press stop, press TUNING MODE 5 repeatedly until “AUTO” then press FUNCTION 8 repeatedly to select “MD”.
Press CLOCK / T I MER SET wg on the remote. If the and “PRESET” disappear, and then press +/– on the
Pause playback X (pause) e; on the remote (or
current mode appears on the display, press ./> remote (or TUNING +/– on the unit) qa repeatedly to To connect an optional digital component
CD u (play/pause) qh on the
qa on the remote repeatedly to select “CLOCK SET?” tune in the desired station. Connect a component with a digital optical input jack
unit). To resume play, press the
and then press ENTER qd on the remote. to the CD DIGITAL OUT jack wa on the unit using
button again. To reduce static noise on a weak FM stereo
3 Set the time. a digital optical cord (square, not supplied). You can
Stop playback x (stop) qk. station digitally record from a CD-DA disc onto the connected
Press ./> qa on the remote repeatedly to set Press FM MODE wh on the remote repeatedly until
Remove a disc Press CD Z (eject) qg on the component.
the hour, and then press ENTER qd on the remote. “MONO” appears to turn off stereo reception.
Use the same procedure to set the minute. unit. Note
Select a group on an Notes on listening to DAB stations You cannot make a digital recording of copy guarded discs and MP3
The clock settings are lost when you disconnect the +/– qf. Or turn the jog dial
• When tuning in a DAB station, it may take a few seconds before you tracks using a digital component connected to this system.
power cord or if a power failure occurs. MP3 disc qs on the unit and press PUSH hear any sound.
ENTER qd on the unit (turn the • Primary service is automatically received when secondary service
To run the DAB Automatic Scan jog dial qs on the unit during ends.
When you turn on the system for the first time after playback until “GROUP” appears,
you purchase the system, DAB Automatic Scan starts and then press PUSH ENTER qd
automatically and creates a list of available services. on the unit to select the desired
If you want to run the DAB Automatic Scan again, group). Playing a tape
perform the procedure below.
Select a track or file ./> (go back/go forward) 1 Select the tape function.
1 Press DAB AUTO SCAN 6 on the unit. qa. Or turn the jog dial qs on
Press TAPE 9 on the remote.
“DAB Auto Scan? Push ENTER” appears. the unit and press PUSH ENTER
qd on the unit. To cancel, press 2 Insert a tape.
2 Press PUSH ENTER on the unit (or ENTER on the
remote) qd. CANCEL qk on the unit. Press TAPE Z (eject) 9 on the unit, and load a TYPE
Find a point in a Hold down m/M (rewind/ I (normal) tape into the cassette holder with the side
Scanning begins. “DAB Auto Scan” appears.
track or le fast forward) qa during playback, you want to play facing forward. Make sure there is
Depending on the DAB services available in your area,
and release the button at the no slack in the tape to avoid damaging the tape or the
scanning may take a few minutes.
desired point. tape deck.

Select Repeat Play REPEAT wh on the remote 3 Press DIRECTION 5 on the unit repeatedly to select
“g” to play one side. Select “h” or “j” to play
repeatedly until “REP” or
both sides.
“REP1” appears.
4 Start playback.
When scanning is complete, a list of available services
is created. To change the play mode Press N (play) e; on the remote (or TAPE nN
Press PLAY MODE 5 repeatedly while the player is (play) 9 on the unit). Press the button again to play
stopped. You can select normal play (“ ” for all MP3 the reverse side.
files in the group on the disc), shue play (“SHUF”or
“ SHUF*”), or program play (“PGM”).
*When playing a CD-DA disc, (SHUF) Play performs the same
operation as SHUF Play.

4
 HCD-CPZ1DAB

Other Operations
Play Timer:
Creating your own CD program Recording onto a tape You can wake up to CD, tape or tuner at a preset time.

(Program Play) You can record on a TYPE I (normal) tape in two ways: Rec Timer:
You can record a preset radio station at a specied time.
Use buttons on the remote to create your own program. CD Synchro Recording: Use buttons on the remote to control the Play Timer and
1 Press CD qh to select the CD function. You can record an entire CD onto a tape. the Rec Timer. Make sure you have set the clock.
2 Press PLAY MODE 5 repeatedly until “PGM” appears Manual Recording: 1 Prepare the sound source.
while the player is stopped. You can record just the portions you like from a sound
For Play Timer:
3 Press ./> qa repeatedly until the desired source, including connected audio components.
Prepare the sound source, and then press VOLUME
track number appears . Use buttons on the unit to control tape recording. +/– qj to adjust the volume.
When programming MP3 les, press +/– qf 1 Load a recordable tape with the side you want to To start from a specic CD track or MP3 le, create
repeatedly to select the desired group, and then select record facing forward. your own CD program.
the desired le.
2 Prepare the tape deck for recording. For Rec Timer:
Press FUNCTION 8 repeatedly to select the tape Tune in the preset radio station.
function. 2 Press CLOCK/TIMER SET wg.
Press DIRECTION 5 on the unit repeatedly and
select “g” to record on one side, or “h” or “j” 3 Press ./> qa repeatedly to select “PLAY SET?”
to record on both sides. or “REC SET?” then press ENTER qd.
Selected track Total playing time of program
To switch the recording sides of the tape, press “ON TIME” appears, and the hour indication ashes.
or le number (including selected track or le)
TAPE nN (play) 9 repeatedly (“B” appears for
recording on the front, and “b” for the reverse side),
4 Set the time to start playing or recording.
4 Press ENTER qd to add the track or le to the
program. and then press TAPE x (stop) 9. Press ./> qa repeatedly to set the hour, and
then press ENTER qd.
“– –.– –” appears when the total time exceeds 100 3 Prepare the recording source.
minutes for a disc, or when you select a CD track The minute indication flashes. Use the procedure
For CD Synchro Recording: above to set the minute.
whose number is 21 or over, or when you select an
Press FUNCTION 8 repeatedly to select the CD
MP3 file. 5 Use the same procedure as in step 4 to set the time
function. to stop playing or recording.
5 Repeat steps 3 through 4 to program additional Load the disc you want to record.
tracks or files, up to a total of 25 tracks or files.
When recording a group from an MP3 disc, press
6 Select the sound source or prepare the tape.
6 To play your program of tracks or files, press N PLAY MODE 5 repeatedly to select “ , ” and then For Play Timer:
(play) e;. press +/– qf repeatedly to select the desired Press ./> qa repeatedly until the desired
The program remains available until you eject the group. sound source appears, and then press ENTER qd. The
disc. To play the same program again, select the CD To record only your favorite CD tracks in your desired display shows the timer settings.
function, and press N (play) e;. order, perform steps 2 through 5 of “Creating your
For Rec Timer:
own CD program.”
To cancel Program Play Load a recordable tape and press TAPE 9 to select
For Manual Recording: the tape function.
Press PLAY MODE 5 repeatedly until “PGM”
Select the desired source to record. Press DIRECTION 5 on the unit repeatedly and
disappears while the player is stopped.
4 Set the tape deck to stand by for recording. select “g” to record on one side, or “h” or “j”
To delete the last track or le of the program to record on both sides.
For CD Synchro Recording:
Press CLEAR wl while the player is stopped. To switch the recording sides of the tape, press N
Press CD SYNCHRO 7. (play) e; repeatedly (“B” appears for recording on the
For Manual Recording: front, and “b” for the reverse side), and then press x
To view program information, such as total
Press TAPE z REC 9. (stop) qk.
track number of the program
Press DISPLAY 4 repeatedly. 5 Start recording. 7 Press I/1 (power) 1 to turn o the system.
Tip While recording, you cannot listen to other sources. The system turns on 15 seconds before the preset time.
You can also use the jog dial qs on the unit to select les in step 3. If the system is on at the preset time, the Play Timer
Turn the jog dial qs and press PUSH ENTER qd on the unit to select For CD Synchro Recording: and the Rec Timer will not play or record.
the desired group, and then select the desired file. Press TAPETAPE X (pause) 9. When the recording is
completed, the CD player and the tape deck stop To activate or check the timer again
automatically. If both sides of the tape are being Press CLOCK/TIMER SELECT wg, press ./> qa
recorded on, and the tape reaches the end of the front repeatedly until “PLAY SELECT?” or “REC SELECT?”SELECT?””
Presetting radio stations side part-way through a track, the entire track is appears, and then press ENTER qd.
You can preset your favorite radio stations and tune recorded again from the beginning of the reverse side.
them in instantly by selecting the corresponding preset For Manual Recording: To cancel the timer
number. Repeat the same procedure as above until “TIMER
Press TAPETAPE X (pause) 9, and then start playing the
Use buttons on the remote to preset stations. OFF?” appears, and then press ENTER qd.
desired recording source.
1 Tune in the desired station (see “Listening to the If there is noise while recording from the tuner, To change the setting
radio”). reposition the appropriate antenna to reduce the Start over from step 1.
noise.
2 Press TUNER MEMORY ea. Tips
• The Play Timer setting remains as long as the setting is not canceled
Preset number To stop recording manually.
Press TAPE x (stop) 9 or CD x (stop) qk (for CD • The Rec Timer is canceled automatically after the Rec Timer has
Synchro Recording only). been activated.
• The volume is reduced to minimum during the Rec Timer.
To pause recording (Manual Recording only)
Press TAPETAPE X (pause) 9.
Notes
3 Press +/– qa repeatedly to select your desired • Recording stops if you change to a dierent function.
preset number. • You cannot eject the disc during CD Synchro Recording.

If another station is already assigned to the selected Tips

preset number, the station is replaced by the new • If you stop the CD Synchro Recording by pressing CD x (stop) qk,
the tape stops aer making about a 4 seconds blank (unrecorded)
stations. space before stopping.
4 Press ENTER qd. • When you record on both sides, be sure to start from the front side.
If you start from the reverse side, recording stops at the end of the
5 Repeat steps 1 through 4 to store other stations reverse side.
You can preset up to 20 DAB, 20 FM and 10 AM
stations. e preset stations are retained for about half
a day even if you disconnect the power cord or if a
power failure occurs. Using the Timers
6 To call up a preset radio station, press TUNING The system offers three timer functions. You cannot
MODE 5 repeatedly until “PRESET” appears, and activate both the Play Timer and the Rec Timer at the
then press +/– qa repeatedly to select the desired same time. If you use either with the Sleep Timer, the
preset station. Sleep Timer has priority.
Note on presetting DAB stations Sleep Timer:
You can preset a DAB service only when it can be received.
You can fall asleep to music. is function works even if
the clock is not set.
Press SLEEP es on the remote repeatedly. If you select
“AUTO,” the system automatically turns off after the
current disc or tape stops or in 100 minutes.

5
HCD-CPZ1DAB
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SET

3-2. CASE
(Page 7)

3-3. FRONT PANEL SECTION

(Page 7)

3-4. TC BOARD, 3-6. MAIN BOARD

MECHANICAL DECK (Page 9)
(CMAL1Z255A)
(Page 8)

3-5. PANEL BOARD 3-7. CD MECHANISM DECK

(Page 8) (CDM80BH-K6BD83S-WD)
(Page 9)

3-9. CHASSIS (TOP) 3-12. DRIVER BOARD, 3-14. BU SECTION 3-8. DAB MODULE ASSY
(Page 10) MOTOR (PULLEY) ASSY (Page 13) (Page 10)
(LOADING) (M701)
(Page 12)

3-13. CD BOARD 3-15. OPTICAL PICK-UP BLOCK

(Page 13) (KSM-213DCP)
(Page 14)

3-10. LEVER (LOADING-L/R) 3-11. LEVER (DISC SENSOR), 3-16. LEVER (BU LOCK)
(Page 11) LEVER (DISC STOP) (Page 14)
(Page 12)

3-17. CLOSE LEVER

(Page 15)

3-18. LEVER (DIR),

GEAR (IDL-B)
(Page 15)

3-19. GEAR (IDL-C)

(Page 16)

6
 HCD-CPZ1DAB

Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE

4 case
2 three screws
(B3)

1 two screws
(case 3 TP2)

3
1 two screws
(case 3 TP2)

3-3. FRONT PANEL SECTION

8 two connectors
1 wire (flat type) (19 core) (CN303, CN307)
(CN603)

2 screw (BVTP3 × 6)
3 terminal

7 wire (flat type) (9 core)

(CN304)

9 front panel section

6 wire (flat type) (19 core)

(CN305)

4 four screws
(B3)

7
HCD-CPZ1DAB

3-4. TC BOARD, MECHANICAL DECK (CMAL1Z255A)

6 terminal

5 four screws
(BVTP3 × 8)

1 flexible flat cable

(8 core)

4 TC board

7 mechanical deck
(CMAL1Z255A) 3 connector

2 three screws
(PTPWH 2)

3-5. PANEL BOARD

q; lid (TC) section

8 two bosses

3 knob (TRE)

4 knob (BASS)

5 torsion spring
(lid TC2)

2 knob (VOL)

1 knob (UD)

torsion spring 7
(lid TC2)

qs PANEL board 6 three screws

qa six screws (B2.6)
(B2.6)
9 bracket (TC)

8
 HCD-CPZ1DAB

3-6. MAIN BOARD

2 back panel
1 six screws
(B3)

5 two connectors
(CN201, CN202)

1 three screws
(B3)

3 flexible flat cable (21 core)

(CN302)

qa MAIN board

4 flexible flat cable (9 core) 8 connector

(CN310) (CN306)

9 flexible flat cable (23 core) 9 connector

(CN308) (CN300)

0 flexible flat cable (15 core) (CN309) 6 two screws (BVTP3 × 6)

3-7. CD MECHANISM DECK (CDM80BH-K6BD83S-WD)

4 AMP/power section
3 two screws
(BVTP3 × 6)

7 cover (CDM)

5 screw
(BVTP3 × 6)

3 screw
(BVTP3 × 6)
1 connector
(CN990)

6 cover board

2 screw (BVTP3 × 6)

9 CD mechanism deck
(CDM80BH-K6BD83S-WD) 8 four screws
(B3)

9
HCD-CPZ1DAB

3-8. DAB MODULE ASSY

1 nut

4 harness

3 connector

5 Remove a solder.

8 DAB module assy

7 DAB board
6 connector

2 two screws
(BVTP3 × 6)

3-9. CHASSIS (TOP)

1 screw
(BVTP2.6)
3 three screws
(BVTP2.6) 2 lever (CL UP2)
4 two screws
(P2 × 10)

5 chassis (top)

10
 HCD-CPZ1DAB

3-10. LEVER (LOADING-L/R)

2 1

SPR-T (loading-R) SPR-T (loading-L)

6 lever (loading-R)

3 two hooks

5 two hooks

4 lever (loading-L)

PRECAUTION DURING LEVER (LOADING-R / L) INSTALLATION

Align the horizontal position.

lever (loading-L) lever (loading-R)

Install the both levers so that they move symmetrically.

11
HCD-CPZ1DAB

3-11. LEVER (DISC SENSOR), LEVER (DISC STOP)

1 gear (cap)

2 gear (IDL-L)

PRECAUTION DURING LEVER (DISC STOP) INSTALLATION

chassis (top)
hole

5 two hooks

3 two claws

6 lever (disc stop) lever (disc stop)

hole

Install the lever (disc stop) so that the both holes

are aligned.
4 lever (disc sensor)

3-12. DRIVER BOARD, MOTOR (PULLEY) ASSY (LOADING) (M701)

2 two screws
(BVTP2.6)

3 Remove soldering
from the two points.
4 DRIVER board

5 motor assy (loading)

(M701)

1 belt (MOT)

12
 HCD-CPZ1DAB

3-13. CD BOARD

5 CD board 1 Remove soldering

from the four points.

3 sheet

4 flexible flat cable (23 core)

(CN102)
2 wire (flat type) (16 core)
(CN301)

3-14. BU SECTION

6 BU section 4 floating screw

(PTPWH M2.6)

3 coil spring (holder down B)

5 screw
(PTPWH M2.6)

2 lever (CL UP2)

1 screw
(BVTP2.6 )

13
HCD-CPZ1DAB

3-15. OPTICAL PICK-UP BLOCK (KSM-213DCP)

1 two screws
(BTTP M2.6)
6 two insulators
7 optical pick-up block
4 two floating screws 2 two stoppers (BU)
(KSM-213DCP)
(PTPWH M2.6)

3 two coil springs (insulator)

5 two coil springs (insulator)

6 two insulators

3-16. LEVER (BU LOCK)

1 floating screw (PTPWH M2.6)

5 lever (BU lock) 4 three hooks

2 gear (cap)

3 gear (BU lock) 2

14
 HCD-CPZ1DAB

3-17. CLOSE LEVER

1 washer (3-1-0.4)
5 close lever

3 claw
2 SPR-E lever close

4 shaft disc stop

3-18. LEVER (DIR), GEAR (IDL-B)

2 capstan retaining ring 3 pulley (gear)

4 gear (cap)

5 gear (IDL-A)

8 stopper

9 lever (DIR)

q; gear (IDL-B)
1 tension coil spring (DIR)

6 Loosen the screw.

7 Hold the Release lever

and change the direction.

15
HCD-CPZ1DAB

3-19. GEAR (IDL-C)

3 gear (IDL-D)

2 two claws
4 three hooks

1 gear (IDL-F)

5 lever (gear loading)

7 gear (IDL-C)

6 claw

16
 HCD-CPZ1DAB
SECTION 4
TEST MODE
COMMON TEST MODE SHIP MODE (NO MEMORY CLEAR)
• This mode is used to check operations of Amplifier. • This mode moves the optical pick-up to the position durable
Procedure: to vibration. Use this mode when returning the set to the
1. Press the I/1 key to turn the power ON. customer after repair.
2. Press three keys of [DSGX] and x (CD) and [PUSH ENTER] Procedure:
JOG simultaneously. 1. Press the I/1 key to turn the power ON.
3. When the COMMON test mode is activated, “SLEEP PLAY” 2. Press the [FUNCTION] key to select “CD”.
blinks on the liquid crystal display. 3. Press three keys of [DSGX], x (CD) and + simulta-
4. Turn the [BASS] knob counterclockwise, “TONE MIN” is neously and the ship mode is set.
displayed on the liquid crystal display. Turn the [BASS] knob
clockwise, “TONE MAX” is displayed on the liquid crystal SHIP MODE (MEMORY CLEAR)
display. • This mode moves the optical pick-up to the position durable
Turn the [TREBLE] knob clockwise or counterclockwise, to vibration. Use this mode when returning the set to the
“TONEFLAT” is displayed on the liquid crystal display. customer after repair.
Turn the [VOLUME] knob counterclockwise, “VOL MIN” is Procedure:
displayed on the liquid crystal display. Turn the [VOLUME] 1. Press the I/1 key to turn the power ON.
knob clockwise, “VOL MAX” is displayed on the liquid crystal 2. Press the [FUNCTION] key to select “CD”.
display. 3. Press three keys of [DSGX], x (CD) and – simulta-
5. To release this mode, press the I/1 key. neously.
4. After the “STANDBY” display blinks, “LOCK” is displayed
PANEL TEST MODE on the liquid crystal display, and the ship mode is set.
• This mode is used to check the liquid crystal display, LED,
model, destination, software version and key. CD SLOT LOCK MODE
Procedure: • This mode is used to unable to take sample disc out of disc
1. Press the I/1 key to turn the power ON. slot in the shop.
2. Press three keys of [DSGX], [DISPLAY] and x (CD) Procedure:
simultaneously. 1. Press the I/1 key to turn the power ON.
3. Liquid crystal display and LEDs are all turned on. 2. Press the [FUNCTION] key to select “CD”.
4. When you want to enter the model, destination and version display 3. Insert a CD disc.
mode, press the [PLAY MODE/DIRECTION/TUNING MODE] key. 4. While pressing the Z (CD) key, press the x (CD) key for
The model and destination are displayed alternately on the 5 seconds.
liquid crystal display. 5. The message “LOCKED” is displayed on the liquid crystal
5. Each time [PLAY MODE/DIRECTION/TUNING MODE] key is display and the disc slot is locked. (Even if pressing
pressed, the display changes starting from MC version, GC the Z (CD) key, the message “LOCKED” is displayed on
version, CD version, CDD version, CDMA version, CDMB the liquid crystal display and the disc slot is locked)
version, BDA version, BDB version, ST version, TA version, 6. To release from this mode, pressing the Z (CD) key, press
TM version, and TC version this order, and returns to the MC the x (CD) key for 5 seconds.
version display on the liquid crystal display. 7. The message “UNLOCKED” is displayed on the liquid crystal
6. Press the [DAB AUTO SCAN] key, the key check mode is display and the disc slot is unlocked.
activated.
7. In the key check mode, the liquid crystal display displays “K0”. CD SERVICE MODE
Each time a key is pressed, “K” value increases. However, • This mode can run the CD sled motor freely. Use this mode,
once a key is pressed, it is no longer taken into account. for instance, when cleaning the optical pick-up.
8. When [FUNCTION] key is pressed while the version numbers Procedure:
are being displayed except model and destination, year, month 1. Press the I/1 key to turn the power ON.
and day of the software creation display. When [FUNCTION] 2. Press the [FUNCTION] key to select “CD”.
key is pressed again, the display returns to the software version 3. Press three keys of [PLAY MODE/DIRECTION/TUNING MODE],
display. When [PLAY MODE/DIRECTION/TUNING MODE] key M L and x (CD) simultaneously.
is pressed while year, month and day of the software creation 4. Press the M L key to move the optical pick-up to outside
are being displayed, the year, month and day of creation of track, or press the l m key to inside track.
the software versions are displayed on the liquid crystal display 5. Press the CD u key, “LD OFF” is displayed and laser diode
in the same order of version display. is turned off. Each time CD u key is pressed, laser diode
9. To release this mode, press three keys in the same manner as ON/OFF switch is performed.
step 2, or disconnect the power cord. 6. To release this mode, press the I/1 key.

COLD RESET CD ERROR CODE MODE

• The cold reset clears all data including preset data stored in • This mode can be used for error display of CD section.
the RAM to initial conditions. Execute this mode when Procedure:
returning the set to the customer. 1. Press the I/1 key to turn the power ON.
Procedure: 2. Press the [FUNCTION] key to select “CD”.
1. Press the I/1 key to turn the power ON. 3. Press three keys of [PLAY MODE/DIRECTION/TUNING MODE],
2. Press three keys of I/1 , [DISPLAY] and x (TAPE) + and x (CD) simultaneously.
simultaneously. Note: Error code is not displayed on the liquid crystal display.
3. The liquid crystal display becomes blank instantaneously, and
the set is reset.

17
HCD-CPZ1DAB

CD SERVO TEST MODE

• This mode used to ckeck operation of optical pick-up.
Procedure:
1. Press the I/1 key to turn the power ON.
2. Press the [FUNCTION] key to select “CD”.
3. Press three keys of [PLAY MODE/DIRECTION/TUNING MODE],
l m and x (CD) simultaneously.
4. When the CD servo test mode is activated, optical pick-up
moves.

CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the I/1 button again to turn the power off (standby).
4. While pressing the x (CD) button, press the I/1 button.
5. It turns power on and display “CD POWER”, then display
“ON” or “OFF”.

18
 HCD-CPZ1DAB
SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
PRECAUTION DECK SECTION 0 dB=0.775 V 3. Mode: Playback
CD SECTION
1. Clean the following parts with a denatured alcohol-moistened
swab: test tape
1. Demagnetize the record/playback head with a head P-4-A063 HP/MD board Note:
record/playback heads pinch rollers (6.3 kHz, –10 dB) PHONES jack oscilloscope
demagnetizer. 1. CD Block is basically constructed to operate without adjustment.
erase head rubber belts (J982) 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
2. Do not use a magnetized screwdriver for the adjustments.
capstan idlers 3. Use an oscilloscope with more than 10 MΩ impedance.
2. Demagnetize the record/playback head with a head de- 4. Clean the object lens by an applicator with neutral detergent when the
• Test Tape V H
magnetizer. set signal level is low than specified value with the following checks.
3. Do not use a magnetized screwdriver for the adjustments. Tape Signal Used for 5. Check the focus bias check when optical pick-up block is replaced.
4. After the adjustments, apply suitable locking compound to P-4-A063 6.3 kHz, -10 dB Azimuth Adjustment
the parts adjusted. FOCUS BIAS CHECK
5. The adjustments should be performed with the rated power RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT
supply voltage unless otherwise noted. oscilloscope
Note: Remove the cover (azimuth) before this adjustment. waveform of oscilloscope (DC range)
TORQUE MEASUREMENT CD board

Mode Torque meter Meter reading in phase 45° 90° 135° 180°
TP (RFACI) +
3.06 N • m to 6.96 N • m good wrong TP (VC) –

FWD CQ-102C 31 to 71 g • cm
(0.43 – 0.98 oz • inch) 4. After the adjustments, apply suitable locking compound to Procedure :
0.19 N • m to 0.58 N • m the pats adjusted. 1. Connect oscilloscope to TP (RFACI) and TP (VC) on the CD
FWD board.
CQ-102C 2 to 6 g • cm
back tension Adjustment Location: Record/Playback/Erase Head 2. Press the I/1 button to turn the power ON, press the
(0.02 – 0.08 oz • inch)
[FUNCTION] button to select “CD”.
3.06 N • m to 6.96 N • m
3. Insert the disc (YEDS-18) and press the CD u button to
REV CQ-102RC 31 to 71 g • cm playback.
(0.43 – 0.98 oz • inch) 4. Confirm that oscilloscope waveform is as shown in the figure
0.19 N • m to 0.58 N • m below. (eye pattern)
REV
CQ-102RC 2 to 6 g • cm A good eye pattern means that the diamond shape (◊) in the
back tension
(0.02 – 0.08 oz • inch) center of the waveform can be clearly distinguished.
6.96 N • m to 14.02 N • m
VOLT/DIV: 200 mV
FF/REW CQ-201B 71 to 143 g • cm TIME/DIV: 500 ns
(0.98 – 1.99 oz • inch)
9.80 N • m forward
Procedure:
FWD tension CQ-403A 100 g or more 1. Mode: Playback level:
0.9 ± 0.4 Vp-p
(3.53 oz or more)
9.80 N • m
REV tension CQ-403R 100 g or more
(3.53 oz or more) test tape HP/MD board
P-4-A063 PHONES jack Checking Location:
(6.3 kHz, –10 dB) (J982) – CD Board (Conductor Side) –
level meter

reverse
set +
–

2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.

within
L-CH 1dB
peak IC201
within TP
Output 1dB (VC)
level

R-CH TP
peak (RFACI)
Screw Screw
position L-CH R-CH position
peak peak

HCD-CPZ1DAB
19 19
HCD-CPZ1DAB
SECTION 7
DIAGRAMS
7-1. BLOCK DIAGRAM – CD SERVO/TAPE DECK Section –

DETECTOR +3.3V

A
57 A
B CD-L
58 B
AC_ EG_
AOUT1 112 A (Page 21)
C 64 65 RFACO 70 71 RFACI PCMD 3 4 PCMDI
SUM IN
59 C AOUT2 117 R-CH
I-V AMP

BCK 5 6 BCKI
D
60 D LRCK 1 2 LRCKI
E
50 E OPTICAL
CD DIGITAL
F DOUT 101 TRANSCEIVER
OUT
51 F IC981

FEO 55
LASER DIODE
CD DSP
AUTOMATIC IC201 TEO 53
POWER CONTROL 66 LD
Q321
PD LD

XTAO
67 PD XTAI
SSTP
39 109 108
SYSTEM CONTROLLER
S201 IC301 (1/3)
(LIMIT) TAPE MECHANISM
X202 DECK BLOCK
OPTICAL PICK-UP BLOCK 16.9344MHz
D +3.3V
(KSM-213DCP) CAPSTAN/REEL
M+10V
TC CAPM CNT1 28 MOTOR DRIVE M
Q692, 694
(CAPSTAN/REEL)
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE TRIGGER TRGM+
IC402 TC TRG 27 PLUNGER DRIVE
Q691, 693
(DECK-A)
16 CH4OUTF
M401 PACK
(SPINDLE) M CH4IN 24 27 OPOUT OPIN+ 2 38 MDP
F REC
15 CH4OUTR TC HALF/REC SW 92 R REC

TC PLAY 73 PLAY SW
17 CH3OUTF CH3FIN 23 41 SFDR
TC END SW 91 END SW
M402
(SLED) M TEI 52

18 CH3OUTR CH3RIN 22 42 SRDR

FEI 54
2-AXIS REC/PB EQ AMP, ALC
DEVICE IC601
14 CH1OUTF CH1FIN 4 43 TFDR
(TRACKING)

13 CH1OUTR CH1RIN 5 44 TRDR ALC 39 11 ALC ON/OFF

TC REC MUTE 38 15 RECMUTE ON/OFF
TC LINE MUTE 34 14 MUTE ON/OFF
(FOCUS)

13 A/B (REC RETURN ON/OFF)

12 CH2OUTF CH2FIN 6 45 FFDR
DATA 89 60 CD-DATA
11 CH2OUTR CH2RIN 7 46 FRDR CLOK 11 37 CD CLK TAPE PB-L
XLAT 16 88 CD XTAL
L-CH
37 BIN (R) PB OUT (R) 5 B (Page 21)
MUTE SENS 20 61 CD SENS 10 REC OUT (R) REC IN (R) 7
20 SCOR 26 19 CD SCOR
XTACN 7 82 CD XTACN R-CH R-CH TAPE REC-L
C (Page 21)
XRST 8 83 CD XRST

HRPE601 BIAS OSC

6 MP3 DATA IN (REC/PB/ERASE) T601
DATA2 12 5 MP3 DATA OUT
REC BIAS
CLK2 90 7 MP3 CLK
SWITCH +9V
• R-ch is omitted due to same as L-ch. XLAT-MP3 13 85 MP3 XLAT Q639, 640
REQ-MP3 14 84 MP3 IREQ
• SIGNAL PATH IREQ-MP3 10 86 MP3 REQ ERASE
: CD PLAY (ANALOG) ACK-MP3 15 87 MP3 ACK
REC/PB SWITCH
: CD PLAY (DIGITAL) Q601, 602 BIAS OSC
3 DR MUTE Q651, 652 Q642, 643
: TAPE PLAY
: TAPE REC LOADING REC/PB SWITCH
M701 79 CDM LOAD OUT Q680, 681, 688
(LOADING) M MOTOR DRIVE
80 CDM LOAD IN
IC701
TC PB/REC SW 33
S701 TC BIAS ON 75
(OUT) 77 CDM SW1 (OPEN)

S702
76 CDM SW2 (CLOSE)
(CHUCK)

HCD-CPZ1DAB
20 20
 HCD-CPZ1DAB

7-2. BLOCK DIAGRAM – MAIN Section –

TAPE REC-L
(Page 20) C HEADPHONE R-CH J982
AMP PHONES
IC502
MUTING
J981
Q414
ANALOG R-CH
INPUT SELECT,
IN
ELECTRICAL VOLUME R-CH
IC501
MUTING
A/D CONVERTER STREAM PROCESSOR POWER DRIVER CONTROL
SEL1 2 Q403, 404
CD-L IC701 IC705 IC707
(Page 20) A
11 D1
OUTL1 11 2 BP OUTA 25
7 B1
TAPE PB-L OUT1 22 1 LIN DOUT 12 31 DATA OUTL2 9 17 AP OUTA 26 +
(Page 20) B 5 A1
BCK 11 30 BCK OUTB 29 L
9 C1 R-CH 2 RIN
–

SOFTMUTE
LRCK 10 29 LRCK OUTR1 6 R-CH OUTB 30 J860

NSPMUTE
SCLATCH
MUTING

PGMUTE
SCSHIFT
SC
OUTR2 4 R-CH SPEAKER

SI

XFSIIN
Q413

SCDT
SCKI

/RST
+

INIT

/SD
18 17 R-CH
XFSOIN
R-CH R
15 36 21 22 23 27 18 19 20 48 4 13
R-CH –
MUTING R-CH DC
CONTROL

SOFTMUTE
DETECT

NSPMUTE
OSC BUFFER R-CH

SCLATCH

PGMUTE
SCSHIFT
Q401, 402 OSC BUFFER Q702, 703
IC703

SCDT
IC709

INIT
LINE MUTE
5 3 PROTECT
2 4
DETECT R-CH
7 1 Q701
SC
SI

6 2
X702
49.152MHz

X701
12.288MHz

TUNER SELECTOR
TUNER (FM/AM) IC421
FM 75Ω
FM ANT L OUT 12 X0
COAXIAL
15 X2 X 13
R OUT R-CH 11 X3
ANTENNA DI
DI A B
AM ANT DO
DO 10 9
AM CLK
CLK
ANT GND CE
CE
TUNED
TUNED
STEREO Q421 Q422
STEREO
ST MUTE
ST MUTE
RDS DATA
RDS DATA
RDS INT
RDS INT

DAB MODULE
LOW-PASS
AUDIO_LEFT_OUT FILTER
ANTENNA
DAB ANT IC803
DAB 75Ω
AUDIO_RIGHT_OUT R-CH

S1_DIN
S1_DOUT
SCDT
SCSHIFT
SCLATCH
INIT
NSPMUTE
SOFTMUTE
PGMUTE
DI
DO
CLK
CE
TUNED
STEREO
ST MUTE

RDS DATA
RDS INT

SI
SC

LINE MUTE

R-ch is omitted due to same as L-ch.

Signal Path
: TUNER (FM/AM) 32 31 23 22 21 24 25 55 2 26 18 59 58 44 43 42 40 41 47 48 46 45
51 50 52 53 54
S-MASTER DATA
S-MASTER SHIFT
S-MASTER LATCH
S-MASTER INIT
S-MASTER NSP MUTE
S-MASTER SOFT MUTE
S-MASTER PG MUTE

S-MASTER RST
S-MASTER SD
: TUNER (DAB)
DAB SELECTOR SW

DAB-MUTE
DAB-DI
DAB-DO

ST DATA OUT
ST DATA IN
ST CLK
ST CE
TUNED IN
STEREO IN
ST MUTE

RDS DATA
RDS INT

AMP SI
AMP SC

HP DET
HP MUTE
LINE MUTE

: CD PLAY
: TAPE PLAY
: TAPE REC SYSTEM CONTROLLER
IC301 (2/3)
: AUX IN

HCD-CPZ1DAB
21 21
HCD-CPZ1DAB

7-3. BLOCK DIAGRAM – PANEL/KEY/POWER SUPPLY Section –

LED DRIVE D901

LED STAND BY 72
Q901 STANDBY

35 LCD DATA
LIQUID D902
CRYSTAL 36 LCD-CLK LED DRIVE
DISPLAY 78 LCD CS LED TUNER 66 TUNER/
Q902
LCD951 63 LCD RESB BAND

D903
LED DRIVE
LED TAPE 65 TAPE
Q903
Y

D904
LED DRIVE
LED CD 67 CD
Q904
u

SYSTEM CONTROLLER
IC301 (3/3)
µ-COM +3.3V

RESET RESET SIGNAL

RESET 12 SWITCH GENERATOR
Q301 IC302
AC CUT 20
SUB POWER
POWER PROTECT2 1 TRANSFORMER
T991
D301 +4V
REMOTE CONTROL RECT
RECEIVER 4 SIRCS E+3.3V REGULATOR
D992 – 995
IC901 IC991
XCIN 10 D302
X301 +1.8V
32.768kHz S-MASTER +1.8V REGULATOR
XCOUT 11
74 WAKE UP KEY IC704
D303 XIN 15 D202
X302
S-MASTER +3.3V
16MHz
XOUT 13 MAIN POWER
D308
RDS +3.3V TRANSFORMER
T31
S901 – 906 97 KEY0 D410
LCD+3.3V
RECT
D405 +28V
A +3.3V D32
SWITCHING SWITCHING
+1.8V +7V +12V
S907 – 912 95 KEY1 Q11 Q12
CD+1.8V REGULATOR
D406 +4V +7V D203 – 205 +12V
IC203 RECT
D +3.3V REGULATOR REGULATOR REGULATOR
D31
IC202 IC201 IC200

S913 – 919 94 KEY2

LED BRIGHTNESS D33

D951, 952 8 9 12 15 16
CONTROL D34
(LCD BACK LIGHT)

VC1
OCP
VG (L)

VS
VG (H)
Q411, 412
PUSH ROTARY
ENTER ENCODER 70 FOLDER A LCD_ON 49 REGULATOR
RV904 71 FOLDER B HEADPHONE AMP B+ VSENSE 1
(JOG) Q551 ISOLATOR
2 F/B VD 18
+5V PH11
ROTARY 68 VOLUME A DAB +5V REGULATOR +9V
VOLUME ENCODER IC805 POWER CONTROL
RV903 69 VOLUME B
+5V +9V IC11
DAB-POWER+5 57 ADC +5V REGULATOR REGULATOR TH1
ROTARY IC204 IC203
TREBLE ENCODER 89 TREBLE +3.3V
RV902 DAB +3.3V REGULATOR RECT
IC801 D1
ROTARY DAB-POWER+3.3 56
BASS ENCODER 90 BASS
RV901
LINE FILTER
T1, 2

F1

RY990
RELAY DRIVE
POWER RELAY ON/OFF 100
Q991

RY991

(AC IN)

HCD-CPZ1DAB
22 22
 HCD-CPZ1DAB

• Note for Printed Wiring Boards and Schematic Diagrams • Circuit Boards Location

Note on Printed Wiring Board: Note on Schematic Diagram:

• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF)
• Y : parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics
• f : internal component. and tantalums.
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise
(The other layers' patterns are not indicated.) specified.
• f : internal component. AMP board
Caution: • 2 : nonflammable resistor. SW POWER board
Pattern face side: Parts on the pattern face side seen from • 5 : fusible resistor.
(Conductor Side) the pattern face are indicated. • C : panel designation.
Parts face side: Parts on the parts face side seen from TC board
(Component Side) the parts face are indicated. Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
• Indication of transistor. Replace only with part number specified.
C • A : B+ Line.
Q These are omitted. • Voltages and waveforms are dc with respect to ground SP board
under no-signal (detuned) conditions.
B E – BD Board –
no mark : CD PLAY
– TC Board – PANEL board DAB module
Q no mark : TAPE PLAY
( ) : TAPE REC
B C E – DAB Board –
no mark : DAB
These are omitted. – Other Section – TUNER (FM/AM)
no mark : TUNER HP/MD board
( ) : CD PLAY
〈〈 〉〉 : TAPE PLAY
{ } : TAPE REC DAB board
• Voltages are taken with a VOM (Input impedance 10 MΩ). OPT board
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope. SUB POWER board
Voltage variations may be noted due to normal produc- SUB PANEL board
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER (FM/AM)
f : TUNER (DAB)
E : TAPE PLAY
a : TAPE REC
J : CD PLAY (ANALOG)
c : CD PLAY (DIGITAL)
j : AUX IN

MAIN board

LCD board

DRIVER board

CD board

HCD-CPZ1DAB
23 23
HCD-CPZ1DAB

7-4. PRINTED WIRING BOARD – CD Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10

CD BOARD (COMPONENT SIDE)

M
CD BOARD M401
(SPINDLE)
(CONDUCTOR SIDE)
C401 S201
(LIMIT)

R280

C405

C406 28 22 21 15
R452 C451

R451
R104
IC402

R107
R421
C C104
R102 R109
R105
M
C272
R110
R423 C109 1 7 8 14
R101 R277
R108 M402
R275
C404 (SLED)

R103
C103
C271 C107
C270 R278
C269 R276

R292
C105
+

C292
30 1

C291
C424 +

C218
C219
31 120
R401 C224
TP R291
C220
D C101
C232
(VC)
IC201 C217
C215 C205

R270
C102 C268 C206 C207

C214
C251
C108 C275
C252 R252
R203
X202 C267 R253 FFC308
C110
C223 C213 R269 CN102
C201 R271 R255

C210
C253 60 91
C222
A
R202 C203 R254
C257 MAIN
C202 61 90 BOARD
R256 C254 TP
R201 CN308
C323 (RFACI) C221
R207 (Page 31)
E C274 C208
C204 R272
R260 C261
C256 C258 R268

R250
R258
R257
C260
C230 R267
C227 R265
C303

C264
R324

C273
C265
R266
R323 12 C112 R112
E 1-868-067- C301
Q321

R322
R321

C321 (12) C113 R113

C322 CN301 C304 R111
C111

F C226

4 3

5 1

IC203 OPTICAL PICK-UP BLOCK

(KSM-213DCP) 12
1-868-067- (12)

HCD-CPZ1DAB
24 24
 HCD-CPZ1DAB

7-5. SCHEMATIC DIAGRAM – CD Board – • See page 48 for Waveforms. • See page 48 for IC Block Diagrams. • See page 53 for IC Pin Function Description.

C210
0.1

TP C208

C264 1000p
(RFACI) 0.1

C273 470p

C260 0.47
C261 0.01
R260 0
C230 R256
100p 22k

C257
0.1

C274
0.1

R265 4.7k
CN301

R250 1M
C265 0.1
C301 16P
0.1
VC

VCC
R266 R321 C303 C304

C258 220p
R258 220k
E

R268 10k
1k 2.2 10 1
C323
R324 C322
100k 100 1 D
10V
R267 R257 C256 R322
A
4.7k 100k 0.1 2.2
C221 B
R323 Q321
0.1 0 2SA2119K
C
AUTOMATIC
F
POWER
C321 CONTROL GND
1000p
LD

VR

PD

F+
TP
(VC)
T+

T-

SVSS

FILO
VDD

SVDD
SSTB-MP3

PCO

AVSS3

VPCO

ASYO
VSS

PD
TEST1

VCTL
DATA

FILI

AVDD3

LD
CLTV

AC_SUM
RFC
AVSS4
RFACI
BIAS

RFACO
ASYI

AVDD4
RFDCO
EG_IN

PDSENS
CLK2 F-
M401
SVSS D (SPINDLE)
C222 0.1 SP+
SVDD C
SP-
JTAGTCK B
SL+
JTAGTDI A
C207 100 10V SL-
JTAGTDO VC
R255 1k C254 4700p
M402
JTAGTMS FEO
R254 10k C253 470p (SLED)
TRST FEI
R253 1k C252 4700p
VSS TEO
C213 0.1 R252 10k C251 470p
VDD TEI
R272 R269
IOVDD2 F
100
DOUT E

TEST AVSS0
C206 0.1
C214 C205 C232
TES1 AVDD0 0.1 0.1
0.1
C223
IOVSS2 CD DSP IOVDD1
0.1
IC201
PLLVDD FRDR
CXD3014A-201R
C267
PLLVSS FFDR
5p
R270
XVSS TRDR
470
C275 C268 C215 X202
R271 XTAO TFDR
3p 22p 0.1 16.9344MHz
1M
XTAI SRDR

R203 XVDD SFDR

R452 C451
AVDD1 IOVSS1 10k 0.047
R113 100
C218 C202 R451
AOUT1 SSTP
R112 100 0.1 0.1 C269 47 4V 22k
R291
C201 VREFL MDP
R111 100 100 100
C217
10V C291 AVSS1 LOCK
0.1
470p
AVSS2 VSS
C424
C270 47 4V
C292 VREFR VDD 0.1
470p
R292 100
AOUT2 VSS R423
C404
10k
0.1
AVDD2 FOK

XLAT-MP3
IREQ-MP3

REQ-MP3

ACK-MP3
IOVDD0 DFCT R421

XTACN
PCMDI

DATA2
LRCKI

PCMD

WFCK

SCOR

COUT
IOVSS0

SVDD
LRCK

CLOK
C219

XUGF

XPCK
0

SENS
XRST

C2PO
SVSS

SVSS
XLAT
MIRR

BCKI

VDD

VDD
BCK

GFS
VSS
0.1
VOUT
STBY

CN102
GND

SVDD
VIN

NC

23P

+1.8V REGULATOR
CD DATA
IC203
MP3 CLK BH18LB1WG-TR
C224
DR MUTE
0.1
D+3.3V
R207 C226 C227 C220
D OUT
0 1 1 0.1

CH2OUTF
CH1OUTR

CH2OUTR

CNF4

CH1FIN

OPIN+
POWVCC

CH2FIN

CH1RIN
GND

CH2RIN

GAIN-SW

OPIN-
CH1OUTF
FFC308 D GND
C203
L OUT R202 100 C204
0 0.1 FOCUS/TRUCKING
10V
A GND COIL DRIVE,
R278 100

R201 SPINDLE/SLED
R OUT 0 R276 C271 C272
MOTOR DRIVE
R275 47k 0.1 0.1

CH4OUTR

CH3OUTR
CH4OUTF

CH3OUTF

CH4CAPA
A+3.3V

POWVCC
100 IC402

PREVCC
CH3RIN
(2/2)

CH3FIN

OPOUT
BA5947FM

CH4IN
CD XATCN

MUTE

VREF
CN308 R277 100

GND
CD XRST

(Page 33) MP3 IREQ

R110 100

R103 100
CD CLK
R105 100
MP3 DATA
R104 100
MP3 XLAT
R109 100
MP3 REQ
R108 100
MP3 ACK R280
R107 100
0
CD XLAT
R102 100
CD SENS
R101 100
CD SCOR

M GND

M+7V
C405 C406
C111 220p

C110 220p

C108 220p

C104 220p

C109 220p

C107 220p
C113 22p

C112 22p

C102 22p

C101 22p

C103 22p

C105 22p

0.1 0.1

R401
0

C401

SL+
SP+
SP-

SL-
220 S201
10V
(LIMIT)

HCD-CPZ1DAB
25 25
HCD-CPZ1DAB

7-6. PRINTED WIRING BOARD – TC Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

• Semiconductor
Location 1 2 3 4 5 6 7
Ref. No. Location
D641 E-4
D681 F-5 HRPE601 TC BOARD
(REC/PLAY/ERASE)
IC601 C-3 A 1
L-CH
Q601 C-3
Q602 B-3
R-CH
Q638 E-5
Q640 E-4 C660 C642
Q642 B-6 R660

JW613
ERASE
Q643 C-6 8 NO601
R657
Q651 C-3
C664
Q652 B-3
Q680 C-4 T601
JW602 JW607
BIAS
Q681 C-4 B C653 C662 OSC
Q688 C-4 JW608 L651 R664

C645

C643
Q691 F-3 C613
C663 E E
Q692 F-4

Q652
Q602
R663 C641
Q693 F-5 R656

Q642
JW611
Q694 F-4 C651
E

C665

C661
C667 E

Q601

Q651
C644 E
R646
R655 E

Q681
R652 R651 R612 JW615
R662 L601 C612
R645
C658 JW614

R653

Q643
C R643

Q680
JW618 R614
IC601 C615

JW638

JW604
C601 E
E R644

JW601
1 40 R617 C611 C646
JW617
C610

Q688
10 31
C656 C635 E
11 30

R607
R610
R635
R658
C657 C614
R603
R659 20 21
C631
D R601 R606

R605
C608 C617
C603

JW612

JW626
R630 R631

K
C632 R613
R602 D641 R648
R661
JW610 A Q638
JW636 R647
E
JW625 E

R609
C607
C606
JW623 Q640
E R622

JW642
R623
JW624 JW633

R625
JW639 R624

R611

R608
R640
JW634

R616
JW600

JW628

R683

Q693
JW632
A K

R684

R685

R687

JW635
C633 D681
C681
E
F FFC301
Q694 E

JW640
R682
B CN603 8 CN602 1
JW631

R633 Q691 Q692 R681

C634
MAIN

JW637
BOARD E E
CN301
(Page 31)
R632
12
(12)

G
R691

R688
R695

R689

R694

R690
R693

R692

FFC601 1-870-852-

TAPE MECHANISM
DECK BLOCK
SUPPLIED WITH THE
ASSEMBLED BLOCK

HCD-CPZ1DAB
26 26
 HCD-CPZ1DAB
Ver. 1.1

7-7. SCHEMATIC DIAGRAM – TC Board – • See page 48 for Waveforms.

FFC601
8P
Q601,602,651,652 Q680,681,688
REC/PB SWITCH Q681 REC/PB SWITCH PLAY SW 1
R662 RT1P141C
10k R REC

Q692,694 Q691,693 F REC

FFC601
CAPSTAN/REEL TRIGGER
Q651 Q601 PACK TAPE MECHANISM
2SC3052F 2SC3052F R612 R617 MOTOR DRIVE PLUNGER DRIVE
10k 10k DECK BLOCK
M+10V
SUPPLIED WITH THE

R602 4.7k
Q680
TRGM+

R613 2.2k
RT1N141C Q694 ASSENBLED BLOCK
KTA1273Y
Q693 MGND
KTA1273Y
END SW 8
C617
C607 C608
Q688 0.1 470p R609 2.2
RT1N141C 2.2k
50V

C603 0.01

R601 4.7k
R603 1k
R687 C681 R683 R695 10k
0.0047
47k 1k
R694 22k
Q652 R608 R611
R693 47k
2SC3052F Q602 C606 4.7k 22k R681
2SC3052F 0.22 R685 R684 D681 R682 2.2k
R688 4.7k
2.2k 2.2k 1SS355W 2.2k
R689 4.7k
Q691
Q692 RT1N141C R690 4.7k
C615 22p RT1N141C
R691 10k
C611 100p
R610 C614 R607 R692 4.7k CN603
10k 0.01 10k R622 R623 R624 R625 19P
L601 27mH R606 2.2k
22 22 22 22 M+12V
R614 C610 R605
100k 470p 47k MGND

C601 TRIG SOL

C663 C612 C660 R655 47
25V CAP MOT
470p 22p 470p C664 R657 47k
0.01 10k
L651 27mH R656 2.2k +3.3V

C661 100p END-SW

R660
C613 10k R631 FFC301
C665 22p HALF.REC
470p 22k

B
PLAY SW
R640
C635 R630 C632
NO601 2.2k
HRPE601 8P 1 50V REC/PB 1M 10 50V BIAS-ON
C631
(REC/PB/ERASE) L-PB EQ AMP,ALC 0.22 REC/PB
IC601
LINE-MUTE
T601 HA12237F C633
R664 C662 10 50V
GND BIAS OSC REC-MUTE
100k 22p
L-CH
L-REC ALC (Page 32)
R-REC PB-R
R616 C634
GND 100 10 50V REC-R
R-CH
R-PB R633 R632 PB-L
C642 10k 1k
GND 0.01 REC-L
100V R635
E-HOT 100 A-GND
ERASE
A+9V
C651
47
25V

Q642

C644 0.0047

C645 0.0047
KTC3198GR
C643 0.01

C646 0.01
R645 22k

R646 22k
R647
22k Q640
Q643 RT1N141C
KTC3198GR
R658 R661
C641
4.7k 22k
47 C658
25V
2.2
50V C653 R651 C656 D641
0.01 4.7k 0.22 1SS355W
R648
10k
R643 R644 R663
4.7 4.7 Q642,643 Q638
2.2k C667 2SA1235EF
BIAS OSC 0.1 Q638,640

R653 R652 C657 R659 REC BIAS SWITCH

1k 4.7k 470p 2.2k

HCD-CPZ1DAB
27 27
HCD-CPZ1DAB
Ver. 1.1

7-8. PRINTED WIRING BOARD – DAB Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6

VIO ANTENNA
DAB MODULE DAB 75Ω
A DAB BOARD

JW810
JW811
R829

R830
C828 C829

CN800

B
JW809 FB801
C820
C821
C818 JW808

R823 JW804 C804

C817 C823
C803
JW805

R832
R802
C822 5
JW807
C R824

JW814
R800

JW802
R812 C805

C832
IC801 1
C816 R811

R826
R814 C815 R813

R827

R825
R810 JW813
R809
R838 R831
FFC310
VIO
C814
C813 R801
R806

R808 IC803
R805 5 CNS801 R
R807 D801 MAIN
IC805 BOARD
CN310
EP801 1 C801

R804
C812
(Page 31)

C811

R803
D C825
JW806
L803 L804 12, 13
1-870-846- (12), (13)

(CHASSIS)

HCD-CPZ1DAB
28 28
 HCD-CPZ1DAB

7-9. SCHEMATIC DIAGRAM – DAB Board – • See page 48 for IC Block Diagrams.

ANTENNA
DAB 75Ω
R803 C811
1k 470p
R805 R807
4.7k 10k
DAB MODULE

R809 R827 R825

4.7k 100k 4.7k
C813 CN800
100p R823 44P
C817
R813 100k
1
V C815 10k R811 50V 1 5V 5V 2
470p 4.7k
LOW-PASS FILTER 3 AUDIO_LEFT_OUT AUDIO_GND 4
IC803
NJM14558V 5 AUDIO_RIGHT_OUT GND 6
TE2 G
C816 R812 C818
7 GND USB_DM 8
470p R814 4.7k 1
10k R824 50V
9 USB_DP GND 10
100k C822
220 11 GND SPDIF_OUT 12
10V
13 GND GND 14
CNS801 R810
9P C825 C814 R806 R808 4.7k
C805 15 S1_DIN S1_DOUT 16
0.1 100p 4.7k 10k R826 C821
DAB-L 100
4.7k 16V R829 0.1 17 3.3V 3.3V 18
FFC310 0
A-GND
19 3.3V GND 20
DAB-R
21 AUD_SFR AUDIO_SDOUT0 22
DAB 7V
R804 C812 FB801
1k 470p 1.1UH 23 AUD_SCLK AUD_MCLK 24
DAB3.3V_ON
25 LCD_DAT_0 LCD_DAT_1 26
DAB5.0V_ON
27 LCD_DAT_2 LCD_DAT_3 28
DAB-DGND
29 LCD_DAT_4 LCD_DAT_5 30
L803
DAB-S1DI
31 LCD_DAT_6 LCD_DAT_7 32
(Page 32) DAB-S1DO
33 LCD_F LCD_LRS 34
CONT

CONT
L804 +3.3V REGULATOR +5V REGULATOR
GND

GND
OUT

OUT
IC801 IC805 35 LCD_M LCD_PE 36
IN

IN
BD33KA5WFP BA50BC0WFP
37 SPDIF_IN RDI_OUT 38

39 SCP_CLK SCP_DAT 40

41 PDM_OUT AUD_SDOUT1 42

43 AUD_SDOUT2 AUD_SDIN 44

D801
1N4002T

R800 C829
1k 0.1
C801 C823
C820 C828
1 4700 0.1 1
10V 6.3V
R801 R802 C803 C804
10k 4.7k 0.22 1

R832 C832 R831 R838 EP801

100 0 0 0
R830
100

(CHASSIS)

HCD-CPZ1DAB
29 29
 HCD-CPZ1DAB

7-10. PRINTED WIRING BOARD – DRIVER Board – • See page 23 for Circuit Boards Location. 7-11. SCHEMATIC DIAGRAM – DRIVER Board – • See page 48 for IC Block Diagrams.
:Uses unleaded solder.

1 2 3 4

A
IC701
BA6956AN
(CHUCK)
S701 S702

CN701
7P

+ R702
100
(OUT)
R701 C711
C
D701 680
MTZJ-4.7C 10 MAIN
50V
M701 BOARD
M (LOADING)
(2/2)

B CN306
(Page 33)
M701 C705
0.01
DRIVER BOARD -

9 IC701 1

1-688-337- 2

C
C MAIN
BOARD
CN306
(Page 31)

HCD-CPZ1DAB
30 30
 HCD-CPZ1DAB
7-12. PRINTED WIRING BOARD – MAIN Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 • Semiconductor
Location
(Page 26) (Page 36) (Page 28) Ref. No. Location
TC BOARD
B CN603 D AMPCN700
BOARD
R DABCNS801
BOARD

MAIN BOARD D202 C-6

A FFC301 FFC302 FFC310
D203 C-8
C562 CN301
D204 B-9
D205 B-9

C508

C507

C557
HT201
D301 F-7

JW289
C560
D302 F-7

JW202
JW201
JW295
JW294
R516 R566 E

R502
C505 Q413 R403 D303 H-9
C512
R501 R453 D305 I-9

JW296
D204
E JW290

R506 R556 C555 JW354 Q401 JW291

D306 I-11

C208
B R551
C510
JW288
C209
C216 JW286 D307 I-10

C558

C506

C556
R552 Q402 3 1
IC203 IC200 D308 I-8

JW203
JW214
E JW292 C207 EP201
E
Q463 D405 E-6

D205
JW350 3 1 C200
4 5

JW360
C509 IC501 C501 JW351 IC204 JW213 D406 E-5
JW356
JW293 (CHASSIS) D410 F-2

C206
1

JW298
3

JW299
JW357

JW297
C503
C527

R523
CN302

D203
JW363

JW392
JW300
IC200 B-9

JW287
JW383
JW381
C559
C554 C504 C214
IC202

JW323
C561 IC201 D-8

JW353
C511

JW355

JW285
C R522 R509
D202 3
FB200
IC202 C-8
C574
IC203 B-8

R550
C524 C565

C218
IC204 B-7

R559
JW393

JW283

C204
C552 1
IC301 G-10

R563
JW394

JW282
JW391
C550 JW307

JW279

HT200

JW396
JW388

JW397
R554 R553
IC302 I-10
JW401

JW204
R558

Q551
JW402

C567 IC201

JW216
R555 R455
C514 C564
C518 E
IC421 E-2
C202 JW395
3
IC501 B-3
C519

JW314
JW284
JW281
JW280
(Page 44)
JW389

JW362
CN201

JW328
JW373
JW371
C217
R436
2 IC502 D-3
C322
IC502 1
H

JW325

JW361
C432

JW221
JW410 1 JW205
D C517 C201 JW206

JW358
JW309
JW310

JW330
JW316
JW315
SW POWER

JW225
C515
Q301 I-10
R432

R505 R404 JR401 BOARD

CN202
JW412 JW411 E 1 JW207
L201 CN32
R503
R504 Q403 2 Q401 B-4
J
R434

E R438 JW370 R557 R406 E JW208

AMP BOARD
Q402 B-4
CN310
Q422 IC421 E R510 R456 Q404 JW209 CN705 Q403 D-5
R507

Q414
E
Q464 JW222 (Page 36) Q404 D-4

JW278
JW277
JW276
R560
R562
JW415
JW413
JW414

JW275
C431

E
Q421 R561 JW231 Q411 F-3

JW227
JW226

JW223

JW224
JW331
R512

1 CN303 7
R435 JW306
Q412 F-2
JW374
JW372

JW369
R421 JW263
JW317
R422
R511 JW303 Q413 B-3
R431 JW319
E R437 Q414 E-3
JW382

E JW416
JW320 JW210 C
R433
C321 D406 JW229 Q421 E-2

D405
JW313 JW321 JW211 DRIVER
HP/MD

JW365
BOARD
R477
Q422 D-2

JW318
BOARD JW312 JW230 JW217 JW220 JW322
JW326 R476 CN701
NO982 C421
JW417 C422 JW311 JW368
JW232 JW215 JW212 (Page 30) Q463 B-3
(Page 42)

JW274
JW273
JW272

JW271
JW270
Q464 E-4
JW385

7 CN306 1
CN305

JW304 JW343 JW305 JW233 JW346 JW341 JW327

Q551 C-4

L411

R380

R378
R376
JW386 JW234
JW344 R440 JW269 JW347 JW342 R439 JW338
JW379

R415
R411

JW418 R410 E JW268

JW380

R547 JW329 R490 JW235 JW219 JW218 JW345 JW339

R379

R374
JW308

R377
3 1

R349
R347

R343
R341
R339
R337
R335
E
F L491 R427

R356
JW267 JW236 R469
3 1 R470

R457

R454
JW377
JW375

R414 Q411 CN300 R428

R413 JW237 R471 R468 R334
Q412 C215 CN307 23 CN308 1

R362
L492 R345 R333

R373
JW238
CN304

22 2 R332
C211

R370
L493
JW340

R354
JW239

R368

R355
D410 A D301 A R360 R331

R366
C210

R348
R346
R344
R342
R340
R338
R336
JW349 D302 R328

R357
JW240
JW387

51

R372
JW332 K K K K R361 50 R327
JW324

R369
R371
JW334
JW333

JW265

JW264

R367
C212 JW241

JW398

R365
JW337
JW336
JW335

JW266
C362
EP301 R430
JW242
IC301 31
R330

JW244

JW243

(FOR CHECK)
R329 1
G

CN400
30
FFC951 FFC901 80
LCD BOARD PANEL BOARD 4
F G CN951 CN901
FFC308
81 R429
CD BOARD SUB POWER
(Page 38) (Page 40) A L R383 R382

R417
(CHASSIS) CN102 BOARD X302 JW245
OPT R385 R384
K

R320
R313
NO992
(Page 24)

R311
JW348

R323
BOARD R387 R386
NO981 (Page 46) R325

JW352
R389 R388
(Page 42) R390
100 1 C316

R322
X301 R326

R318
R391
R392 A D303 C407
C301 R425

R303
R305
R474 C405

JW251
R494 K K C311 R321
R324

R400
H R495
R394

JW252

R304
R306
R395

R309
C310
R302
JW248
R493 JW247
R397 JW249

R497
JW257
JW250
R405 R307

JW256

JW255
R402

D305
C312
Q301

JW253
JW259
JW258

R301 E R412

JW254
R319

R401

C403
R420
C404
JW260

JW359
C351
C309

JW378

C359 JW261
I CN309 C401
JW262
FFC309 3 1

D307
D306
C402
JW376
FM 75Ω TUNER 4 5
COAXIAL
(FM/AM)
SUPPLIED
D308 IC302
ANTENNA 12
WITH THE
ASSEMBLED 1-870-842- (12)
AM EP302
BLOCK

(CHASSIS)

HCD-CPZ1DAB
31 31
HCD-CPZ1DAB

7-13. SCHEMATIC DIAGRAM – MAIN Board (1/2) – • See page 48 for IC Block Diagrams.

CN301
19P
M+12V
(1/2) MGND
INPUT SELECT,ELECTRICAL VOLUME
27 TRIG SOL
IC501
C503
220 C527 BD3872FS 28 CAP MOT
10V 0.1
R523 1k 50 +3.3V
GND SC
+7V REGULATOR
R522 1k 51 91 END-SW
FILTER SI IC201
TA7807S 92 HALF.REC
E2 VCC FFC301
73 PLAY SW
C501
E1 CAP 0.1 O G I
C564 1 50V C555 10 50V 75 BIAS-ON
D203

-MD-
D2 OUT2
C514 1 50V C505 10 50V C217 C202 1N4002T 33 REC/PB
1 0.1
D1 OUT1
JW402 C556 0.1 R566 D204 34 LINE-MUTE
C2 BOUT2

-ST-
4.7k 1N4002T
JW401 R556 220k C557 0.1 38 REC-MUTE
C1 BNF2
C561 10 50V C506 0.1 39 ALC
B2 BOUT1 R516 D205
(Page 27)

-CD-
CN302 4.7k 1N4002T
C511 10 50V R506 220k C507 0.1 PB-R
21P B1 BNF1
+4V REGULATOR
A+5V C562 1 50V C558 0.0022 REC-R
A2 TNF2 IC202

-TC-
D202
AGND C512 1 50V C508 0.0022 TA7804LS PB-L
1N4002T
A1 TNF1
R IN C560 1 50V REC-L
SEL2 SOUT2 O G I
AGND C559 A-GND
1 VIN2 SQI2
L IN 50V C218 C204 A+9V
1 0.1
SEL1 SOUT1
P DOWN C510 C509 VIN1 SQI1
FFC302 1
1
DGND R509 50V 50V
10k
D+3.3V

INIT 40

NSP MUTE 41

DGND
A1
SC LATCH 42 TUNER SELECTOR
IC421 A2
(Page 34) SC SHIFT 43 MC14052 C524 2200p
A3
SC DT 44 B C574 2200p
A4
GND
/SD 45 A C432 R436
DGND
VEE 0.1 100 (Page 33)
X3
INH
/RST 46 R438 100k
X0 R453 R551 R501
Y1 10k 1k 1k
SOFT MUTE 47 R432 100k
X Q463 C209
Y3 2SC5938 470
PG MUTE 48
X1 Q402 10V
Y RT1P141C +5V REGULATOR
OVF R434 100k
X2 R403
IC204
/OTW Y2 10k Q401,402 MM1615ANLE
VCC Q413 C208
Y0
2SC5938 MUTING CONTROL 0.1
R435 Q413,463 IN
CN303 470 CONT
7P R511 R512 MUTING GND
1k 10k
MD L R421 100k
CN
Q401 OUT
MD GND R422 100k
R561 R562 RT1N141C C216
1k 10k 0.01
MD R
Q422 Q421
HP DET 54 R437 100k 52
C431 RT1N441C RT1N441C
0.1
HP L INVERTER INVERTER

HP GND R433 100k

HP R 59 +9V REGULATOR
R552
(Page 43) 10k R502
10k 58
IC203
TA7809S
CN310
9P
O I
G
DAB-L C421 1 50V R431 100k C554 C504
1 1 C207
FFC310 C206
A-GND 50V 50V 470
0.1
10V
DAB-R C422 1 50V 49

DAB 7V

DAB3.3V_ON

DAB5.0V_ON 57 CN202
L201 2P
0
DAB-DGND R553 12V
1k
(Page 29) DAB-S1DI 31 R414
100
R415
22
R455
100k
Q551
KTC3198GR
GND

DAB-S1DO 32
REGULATOR
R558 +12V REGULATOR

CN304
56
Q412
2SA1235EF
22k
R563
IC200
(Page 35)
BAJ2DD0T
7P R413 JR401 C565 100
22 0 10 HEADPHONE AMP CN201
LED 5V
FFC951 50V FB200 2P
IC502 O G I 1.1UH
LCD CS 78 NJM4580MD C552 C550 C201 C200 16V
R503 R404 R559 R550 C214
10 22 4700 1
LCD SCL 36 R410 R554 1k 100k 22k 50V 50V 22k 16V 0.1 50V GND
Q411,412 10k 4.7k
G
LCD DATA 35 LED
BRIGHTNESS R555
LCD RESB 63
CONTROL
R411
2.2k
D410
1N4002T
22k (Page 45)
LCD+3.3V
V R505 R504 C515
22k 4.7k 10
DGND
C567
(Page 39) Q411
220
10V
50V

CN305 RT1N141C
19P
R557
+7V
47 Q404
LED GND RT1P141C

LED TAPE 65
Q464 Q403
E+3.3V R560 2SC5938 RT1N141C 53
100k
SIRCS 4 R456 C519 C518
100
1k 0.1
DGND 16V

LED TUNER 66
FFC901 Q403,404
Q414
LED CD 67
R510 2SC5938 MUTING CONTROL
100k
NC
R406
VOLUME A 68 1k

VOLUME B 69
Q414,464 R507 C517
47 220
FOLDER A 70 MUTING 10V
A5
FOLDER B 71
(Page 41) KEY2 94
A6

A7
KEY1 95
A8
KEY0 97
A9
LED STANDBY 72
A10
TREBLE 89
A11
BASS 90
A12

A13
(Page 33)
A14

HCD-CPZ1DAB
32 32
 HCD-CPZ1DAB

7-14. SCHEMATIC DIAGRAM – MAIN Board (2/2) – • See page 48 for Waveforms. • See page 48 for IC Block Diagrams. • See page 53 for IC Pin Function Description.

(2/2)

R477 10k

R476 10k

R471 10k

R470 10k

R469 10k

R468 10k

R457 10k

R454 10k
R474 1M
A1
D302
A2 MC2836

A3

54

52
80

63

58
68

65

60

59

56
69

66

51
73

61
78

75

70

57
79

76

67
71
77

72

53
(Page 32) A4
CN309
15P
26 RDS DATA

C362 0.1
18 RDS INT

R380 100

R379 100

R378 100

R377 100

R376 100

R374 100

R373 100

R372 100

R371 100

R370 100

R369 100

R368 100

R367 100

R366 100

R365 100

R362 100

R361 100

R360 100

R357 100

R355 100

R354 100
R356 10k
CN306
FM SIGNAL OUT
7P D308
MGND 1N4002T RDS +3.3V

RIN(NEG) 80 2 ST MUTE FM 75Ω

COAXIAL
FIN(POS) 79 C322 1 50V R OUT

M+7V C359 0.01 AGND FFC309

TUNER (FM/AM) ANTENNA
SW3(TRIGGER SW) C321 1 50V L OUT
SUPPLIED WITH
SW1(OUT SW) 77 STEREO
THE ASSEMBLED
SW2(CHUCK SW) 76 25 C309 0.01 TUNED BLOCK
(Page 30) C351 0.1 +9V AM
CN307 D303 R439
24 CE
3P MC2836 10k

LOAD

WAKE UP KEY
CDM SW2 (CLOSE)

VOLUME A

VSS

HP DET

AMP
SI
LED TAPE

LCD RESB

DAB-P0WER3.3
VOLUME B

LED TUNER

DAB SELECTOR SW

DAB-POWER5.0
TC PLAY

LED STAND BY

FOLDER A

VDD

STEREO IN
CD DATA
CDM SW1 (OPEN)

TC BIAS ON
CDM LOAD OUT

FOLDER B

LED CD

CD SENS

DAB-MUTE

LINE MUTE
HP MUTE
IN

LCD CS
CDM
DGND 23 DI

D+3.3V L491 0 22 DO
50
CD POWER
D OUT ON/OFF AMP SC 21 CLK
82 R382 100 R349 1k 49
R547 CD XTACN LCD_ON
83 R383 100 R348 100 48
CN308 220
CD XRST S-MASTER PG MUTE EP201
23P 84 R384 100 R347 100 47
(Page 43) CD DATA 60
85 R385 100
MP3 IREQ S-MASTER SOFT MUTE
R346 100 46
MP3 CLK 7 MP3 XLAT S-MASTER RST
D306
86 R386 100 R345 100 45 1SS355W
DR MUTE 3 MP3 REQ KEY0 S-MASTER SD EP302
87 R387 100 R344 100 44
D+3.3V L493 0 MP3 ACK VREF S-MASTER DATA
88 R388 100 R343 100 43
D OUT CD XLAT AVDD S-MASTER SHIFT
D307
89 R389 100 SYSTEM CONTROLLER R342 100 42
POWER RELAY 1SS355W
DGND R440 D406 TREBLE ON/OFF IC301 S-MASTER LATCH
FFC308 90 R390 100 R341 100 41
1k 1N4002T M30624MGP
L OUT BASS S-MASTER NSP MUTE EP301

PROTECT2
A59FPU0 C215

DR MUTE
91 R391 100 R340 100 40

ST MUTE
0.1
AGND TC END SW S-MASTER INIT

POWER

SIRCS
92 R392 100 R339 100 39
R OUT R490 1k TC HALF/REC SW ALC
R493 4.7k R338 100 38 C210
0.1 (CHASSIS)
A+3.3V L492 0 SPEC IN TC REC MUTE
94 R494 10k R394 100 R337 100 37
CD XTACN 82 KEY2 CD CLK
C211
95 R495 10k R395 100 R336 100 36 0.1
CD XRST 83 KEY1 LCD-CLK
C405 0.1 R335 100 35
MP3 IREQ 84 AVSS LCD DATA
C212
97 R497 10k R397 100 R334 100 34 D301
CD CLK 37 TC LINE MUTE MC2836 0.1

(Page 25) R333 100 33

MP3 DATA OUT

MP3 DATA 5 TC PB/REC SW

ST DATA OUT
MP3 DATA IN
R332 100 32
C407

ST DATA IN
MP3 XLAT 85 DAB-DI

RDS DATA
0.1

TUNED IN
R331 100 31

CD SCOR

TC CAPM
MP3 CLK

RDS INT
MP3 REQ 86 DAB-DO

TC TRG
AC CUT

IIC CLK
CN VSS

ST CLK
XCOUT

RESET

ST CE
XOUT
R428 R427 CN300

CNT1

DATA
BYTE

XCIN
MP3 ACK 87

VDD

NMI
VSS
10k 10k 3P

XIN

IIC
CD XLAT 88 RELAY ON
R400
100
CD SENS 61 4V(EVER)

CD SCOR 19 GND

MGND

M+7V

L411 R330
CN400
4P
(Page 47)
D405 0 100
1N4002T
R311 100k
R405 22k

R302 100

R303 100

R304 100

R305 100

R306 100

R307 100

R319 100

R320 47k

R321 100

R322 100

R323 100

R324 100

R325 100

R327 100

R328 100
R301 10k

R309 10k

R417 10k

R429 10k
A5

R313 0
NC
A6 R329
100

6.3V
A7
R430
10k
C311 22p

C301 1000
A8 4
32.768KHz

R412 10k

R425 10k
C316 0.1
X301

A9

A10
C310

19
A11
22p RESET SIGNAL GENERATOR
3

(Page 32) A12

A13

A14
R420
10k IC302 C402
PST3629NR
R318 100

R326 100
C312 0.1
0.1
R401 C404 OUT
47k 0.1 CD
VDD
Q301
2SC3052F X302 GND
RESET 16MHz NC
D305 R402 C403 C401
27

28
SWITCH
18

1SS355W 47k 0.1 0.1

2

21

22

24
23

25

26

HCD-CPZ1DAB
33 33
 HCD-CPZ1DAB

7-15. SCHEMATIC DIAGRAM – AMP Board (1/2) – • See page 48 for Waveforms. • See page 48 for IC Block Diagrams.

(1/2)
A1

PDWN

INIT

OVF

SCLATCH

SCSHIFT

SCDT

PGMUTE

SOFTMUTE

NSPMUTE

C787 0.001
R789 100

R788 100

R787 100

R786 100

R785 100

R784 100

C788 0.1
R783
100

CN700 C731
OSC BUFFER
21P L701 47 D701
0 25V 1SS355W IC709
TC7SHU04FU
A+5V

AGND
C786
R IN C748 0.001 VCC
C729 C701 R701 10 R730
AGND D702 50V R790 100
0.001 2.2 50V 0 100
1SS355W L704
L IN 10µH GND
PDWN
P DOWN C751 R751 C749 C785
2.2 50V 0 0.1 10p
DGND

FFC302 R782
D+3.3V 1M C796 0.1
INIT D703 1SS355W
C740

D
INIT 220 R781
NSPMUTE D704 1SS355W
10V 100
NSP MUTE

DGND

C730 0.1
SCLATCH X702 C784

C733 0.1
0.001

R729 1k

C732 0.1
SC LATCH L705 1µH 49.152MHz C752 0.1
R741
SCSHIFT 100
SC SHIFT C783 10p
SCDT
(Page 32) SC DT
C806
R743
R742 TP723
/SD 100 A2
/SD 0.1 10k C704 0.001

DGND R745 R744 0

/RST A3
100
/RST
SOFTMUTE STREAM PROCESSOR
SOFT MUTE
PGMUTE IC705
PG MUTE R748 47k R747 100
CXD9788AR (Page 35)
OVF A4
OVF C745 0.01 C754 0.001
/OTW
/OTW
A5
R749 0

C746 0.01
A/D CONVERTER
IC701
PCM1802DBR
C747 100 16V

C750
0.01
+1.8V REGULATOR
IC704
NJM2871BF18
R746 C797
C792 100 0.01
VOUT
0.1
NOISE
C735 GND
10
VIN A6
50V
C741 C734 R750 CONT

C780 0.001
0.1 0.001 47k C798

C799 0.1

C779 0.1
EP703 C831 0.1 L702 100
10µH 16V
C832 0.01

C753 R779
(CHASSIS) C761 100 0
0.01
16V
C737 L703 A7
0.01 10µH

R737 C738
1k 15p

OSC BUFFER
IC703
TC7WU04FU
R736 X701
R731 1M 12.288MHz
220
VCC

R734
0 C739
12p

GND
R733
220

HCD-CPZ1DAB
34 34
 HCD-CPZ1DAB

7-16. SCHEMATIC DIAGRAM – AMP Board (2/2) – • See page 48 for IC Block Diagrams.

(2/2) EP705

A1

/SD
/OTW

/RST
(CHASSIS)
EP706

(CHASSIS)
EP702

POWER DRIVER (CHASSIS)

IC707 EP701
CXD9774M
C842 C843 C840 C841 C828 C839 C829
1000p 0.1 1000p 0.1 1 1 1
(CHASSIS)
R704 0 C813 C827 C830
1 1 1
C718
0.047

L709
R706 L710 R721 C722
100 10µH 10k 0.0022
R707
0 C723 C844 CN702
C781 0.1
C744 D705 C716 C717 R720 0.0022 0.1 2P
0.1 C708 0.1 P6SMB39AT3 0.22 0.22 3.3 L+
C720 R739 R724

R708 0
1 10k 4.7

L-
M
D706
P6SMB39AT3
C848
0
R718
10k
R725
4.7
C845
0.1
(Page 37)
R709 0
C724
C709 0.1 R726
C714 C715 R719 0.0022 220k
0.22 0.22 3.3
R711 100
L711 C728 R740 C725
10µH 1 10k 0.0022

R712 100
L708 R728
C706 220k
C713 1
R714 470 0.047 Q702
C726 R727
2SA1235PNP
2.2 100k

Q702,703
R713 C710 R800 C712 C719 Q701
A2 1 DC DETECT
22k 47p 1k R716 R723 R717 R738 2200 2SC3052NPN
TP748 1k 1k 1k 1k 35V PROTECT Q703
R765 2SA1235PNP
A3 0 DETECT

Q752
R792 2SA1235PNP
D713 C702 0
UDZSTE-172.4B 0.1
A4
(Page 34)
R801 POWER DRIVER C703 R793 C778 R777
1k 0.1 47k 2.2 100k
A5 IC708
CXD9774M
Q752,753
C794
R754 R752 C757 1 DC DETECT
470 22k 47p Q753 R776
2SA1235PNP 220k
C756
C791
1 C711 0.1
R756 100 220
C768 L760 R778
16V 10µH
0.047 L759 220k

R757 C782 R771 C772

0 0.1 10k 0.0022
C766 C767 R770
0.22 0.22 3.3 C773 C846
C758 0.1 0.0022 0.1 CN703
2P
D755 C849 C770 R772 R774 R+
P6SMB39AT3 0 1 10k 4.7

N
R758 0
A6
R759 0
R768 R775
C759 0.1 C769
10k 4.7 R- (Page 37)
D756 C764 C765 R769
P6SMB39AT3 0.22 0.22 3.3 2200 C774 C847
R761 100 35V
0.0022 0.1
C777 R773
L761 1 10k C775
A7 10µH
R762 100 0.0022
L758

C763
CN704
0.047
R764 0 5P

GND
C762
1
28V

GND

28V
P
(Page 45)
GND

CN705
2P

GND

12V

(Page 32)

HCD-CPZ1DAB
35 35
 HCD-CPZ1DAB

7-17. PRINTED WIRING BOARD – AMP Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

• Semiconductor 1 2 3 4 5 6 7 8 9 10 11
Location
Ref. No. Location
D701 B-8 AMP BOARD (COMPONENT SIDE) AMP BOARD (CONDUCTOR SIDE)
(CHASSIS)
D702 B-8 A
D703 A-8
C750 C735
D704 A-8 R734 C792

D703
D704
X701
D705 D-8 R737
IC703 C729

C741
C738

C733
D706 D-8 IC701
C748 C798
C737
D713 E-5

R736
C734 EP703
D755 D-10 R730 CN700
C739

D756 D-10 R731 R729 C730

L701 C761

C749

C732

C832
C831
L703
R733

L702
C746 C797 1 5
D701 C747
IC701 B-4 R750

IC703 B-3
B R746
R745 R701
C731
D702 3 4

R748
R747
IC704 B-10
R749
R741
IC704
R779 IC705 36 25 R751 C751 R742
IC705 C-3 37 24
R790 R743 C745
FFC302
IC707 D-4 C799
C701 C806
R789 R744
IC708 D-2 D
R781
C779
C784

C783
X702 R788
IC709 C-2 C780
48 13 MAIN
L704

L705
R784 R787 BOARD C740
R783

R785
R786
5 4 CN302 C786
Q701 F-1 1 12
C787
Q702 G-5 C788 (Page 31) C753

C 1 3 R782
C754 C704

C785
Q703 G-5 IC709
Q752 G-2
Q753 G-2 R758
C752
R757 R708 C796
R707
R756 R706
R712
R754 R714 R704 C759
C758
C744
R764
R762
R761

C708
R759 C709

R709
R711
R752 R713
C757 C781
IC708 C710
IC707 C782
C841
EP705
EP706
D C843 C840

C842

D705 D706 D755 D756

R720 C763
D713
R769 R770 R719 (CHASSIS) C762 (CHASSIS)

C768
C718

C713
C706
R716

R800
R801

C756
C712
R765
C765 C764 C766 C767 C715 C714 C716 C717 L709 L708 L759 L758
E R723

L710 L711 L760 L761

C848 C849
R717 C702 C791
C703 C720 C728 C770 C777
R738
F Q701

E R721 R718 R771 R768

R793
R739 R740 R772 R773
C794

R792 C711
C719 C769

C829

C830
C839

C827

C828

C813
CN705
E
Q703
Q753

C726 R727 C722

G C778 R777
R778 R726
E
C725
1 2
C772
C775

R775
EP701

C845
C844
C723 EP702

C847
E C724 C773
R728
Q752

R776
Q702

C846
R724 CN702 R725 R774 CN703 C774
E
1 2 5 CN704 1 1 2

12
1-865-283- (12)

1-865-283- 12

H (CHASSIS) M P J N (CHASSIS)
(12)

SP BOARD SW POWER MAIN SP BOARD

CN850 BOARD BOARD CN870
(Page 37) CN31 CN202 (Page 37)
(Page 44) (Page 31)

HCD-CPZ1DAB
36 36
 HCD-CPZ1DAB
Ver. 1.1

7-18. PRINTED WIRING BOARD – SP Board – • See page 23 for Circuit Boards Location. 7-19. SCHEMATIC DIAGRAM – SP Board –
:Uses unleaded solder.

1 2 3

SP BOARD M CN850
2P

A C851
470p J860

C852
(Page 35) 470p L

SPEAKER

CN870 C853 R
470p

2
C854
– N CN870
2P
C854

N 1
470p

B AMP
C853
R
BOARD
CN703
+ (Page 35)
(Page 36)

J860
SPEAKER

CN850
C852

C 2 –

M 1
AMP L
BOARD C851
CN702 +
(Page 36)

12, 13
1-870-843- (12), (13)

HCD-CPZ1DAB
37 37
HCD-CPZ1DAB

7-20. PRINTED WIRING BOARD – LCD Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8

LCD BOARD
(Page 31)
A F MAIN BOARD
CN304
FFC951

CN951

B
D951

R954

R955
R956

R957
R961

LCD951
D951, D952
LIQUID CRYSTAL DISPLAY
LCD BACK LIGHT

D952 C965
C
JW951 JW952
R959

C957 C955

C956 C954 C952

C953
C951

1 9
D 12
1-870-851- (12)

HCD-CPZ1DAB
38 38
 HCD-CPZ1DAB

7-21. SCHEMATIC DIAGRAM – LCD Board –

D952
SELU2WA10C
D951,952
(LCD BACK LIGHT) R959 47

D951
SELU2WA10C
R961 47
CN951
7P

SDA
RES

CSB

SCL
C965 0.1 LED 5V

CSB R954 100 LCD CS

SCL R955 100 LCD SCL FFC951

100p

100p

100p

C954 100p
SDA R956 100 LCD DATA

C957

C955
C956
RES R957 100 LCD RESB
C952 C951
1 1 LCD+3.3V

DGND

C953
1
(Page 32)

VAP1N
CAP1P
VOUT
VSS
CSB
RES

VDD
SCL

SDA

LCD951
LIQUID CRYSTAL DISPLAY

HCD-CPZ1DAB
39 39
HCD-CPZ1DAB
7-22. PRINTED WIRING BOARDS – PANEL Section – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

• Semiconductor 1 2 3 4 5 6 7 8 9 10
Location
Ref. No. Location
D901 E-9 D903

D902 E-2 A
D903 A-2
D904 B-4

C912
PANEL BOARD SUB PANEL BOARD
D903, S910
IC901 E-9 TAPE
Y D904
S913
Q901 F-10
S910
Q902 E-2
C914
Q903 E-2 Z (CD)
Q904 E-2
Q905 E-1 B R908
NO901
D904, S912
CD
1
u
x S909 S912
(TAPE)

R909 4
R907
R910

C X S908
x
(TAPE) S911
/CANCEL
(CD) 12
R906 (12)
1-870-848-

S907

z REC

CN902

E
Q904

R930

D902 D901
Q905

Q902 PLAY MODE/

E E
E
C913
DAB DIRECTION
R905 AUTO SCAN TUNING MODE DISPLAY
STANDBY
E
Q903

IC901
R926

R928
S906 S905 S904 S903 S914
D902, S915
R911 R922 S901
TUNER/ R904 R903 R902 R921
BAND R923 3 1
FUNCTION CD
R913 SYNCHRO C905 I/1
S915

R912 R920

JW912
JW917
F

JW907

JW904

JW914

JW905

JW906

JW916

JW913

JW915

JW922
Q901

JW925
E
JW923

+ S916 R924

JW909 C908
JW920

C909
TUNING JW910
JW919
JW924
G − S917
R914
DSGX

JW903

JW908

JW911
1 3

R939

C907
R937

R933

R935

C906
S902

JW921
R915 RV903
R916 ROTARY ENCODER
C910 C911 R901

R932

R934
R938
R936
3 1
1 3 1 3

RV902 RV901
RV904 + S918
ROTARY ENCODER ROTARY ENCODER ROTARY ENCODER

H
VOLUME

R917

5 4 CN901 TREBLE BASS

PUSH ENTER − S919

(JOG) 12
I 1-870-847- (12)
FFC901

MAIN BOARD
G CN305 (Page 31)

HCD-CPZ1DAB
40 40
 HCD-CPZ1DAB

7-23. SCHEMATIC DIAGRAM – PANEL Section –

RV901 RV902
ROTARY ROTARY RV903
ENCODER ENCODER ROTARY ENCODER
BASS TREBLE VOLUME

COM

COM

COM
RV904
1A

1B

1A

1B

B
PUSH ENTER
1 2 3 1 2 3 1 2 3 (JOG)
C911
0.1
FOLEDER B

R932 R934 R936 R938

2.2k 1k 2.2k 1k

C908 0.1

C909 0.1
FOLEDER A
C906 R935 R937 C907 R939
R933
0.1 10k 4.7k 0.1 10k C910
4.7k 0.1

VOLUME B
VOLUME A
TREBLE
BASS

D904
SELK5E20C
S913
R912 R911 R913 R914 R915 R916 R917 CD
1k 2.2k 2.2k 4.7k 10k 22k 47k
S918 S919
CN902 NO901 (CD)
S915 S916 S917
S914 4P 4P C914
DISPLAY TUNER/ TUNING TUNING 0.1

BAND + - + - LED CD LED CD

S911 S912
LED GND LED-GND
/CANSEL CD
KEY2 KEY2
(CD)
R901 R902 R903 R904 R905
KEY1 KEY1
1k 2.2k 2.2k 4.7k 10k
R909 R910
S903
4.7k 10k
S901 S902 S904 S905
PLAY MODE D903
DSGX D902
DAB CD S906 C913 SELK5E20C C912
DIRECTION R921 D901 SELK5E20C
AUTO SCAN CYNCHRO FUNCTION 470 0.1 0.1
TUNING MODE SEL5220S TAPE
TUNER/
STANDBY
BAND
Q903
Q901 Q902
2SC3052F
2SC3052F 2SC3052F 1.6
R906 R907 R908 LED DRIVE
+3.3V

1k 2.2k 2.2k GND LED DRIVE LED DRIVE

OUT
S907 S908 S909 S910 REMOTE CONTROL

(REC) TAPE RECEIVER 3 2 1 R924 R926 R928

IC901 10k 10k 10k
(TAPE) (TAPE) NJL24H400A C905
1
R920
220

LED-STANDBY

LED-TUNER

LED-TAPE
R922 220

R923 470
BASS

TREBLE

3.6 R930
LED-STANDBY

FOLEDER B

FOLEDER A

VOLUME B

VOLUME A

LED-CD

LED-TUNER

LED-TAPE

LED-CD

10k 3.3
Q904 3.1
2SA1235EF

Q905
RT1N141C

Q904, 905
LED DRIVE
BASS

TREBLE

LED STANDBY

KEY0

KEY1

KEY2

FOLDER B

FOLDER A

VOLUME B

LED CD
VOLUME A

NC

LED TUNER

D GND

SIRCS

E+3.3V

LED TAPE

LED GND

+7V

CN901
19P

FFC901

G
(Page 32)

HCD-CPZ1DAB
41 41
HCD-CPZ1DAB

7-24. PRINTED WIRING BOARDS – JACK Section – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7

(Page 31) (Page 31)

MAIN BOARD MAIN BOARD
E CN303 K CN307

A HP/MD BOARD OPT BOARD

NO982

C992 C991 NO981

C986 R981
C990
C983
EP981
C982

1 3
(CHASSIS)

FB981

FB982

FB983
C984 C985

R985
IC981
B R982
R983

R984 12
JW981 1-870-850- (12)

CD
DIGITAL
OUT

C 12
1-870-849- (12)

D J981
ANALOG
J982

PHONES
IN

HCD-CPZ1DAB
42 42
 HCD-CPZ1DAB

7-25. SCHEMATIC DIAGRAM – JACK Section –

J982 FB983 C992 C991

0 0.022 0.022
PHONES

FB982 C990
0 0.022
NO982
7P
C986
HP R
0.1
FB981
HP GND
0
EP981

R984
HP L

HP DET
E
1k MD R
(CHASSIS) C983
0.1 R985 C985 MD GND
100k 470p
MD L (Page 32)
R983 C984
J981
100k 470p
ANALOG
IN R982
1k

OPTICAL
TRANSCEIVER
IC981
TOTX141L R981 NO981
1k 3P

CD
OUT 3 D OUT

D+3.3V
K
DIGITAL +3.3V 2
OUT DGND

GND 1
C982 (Page 33)
1

HCD-CPZ1DAB
43 43
HCD-CPZ1DAB

7-26. PRINTED WIRING BOARD – SW POWER Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

• Semiconductor
1 2 3 4 5 6 7 8 9 10
Location
Ref. No. Location (Page 36)
AMP BOARD
D1 F-4 SW POWER BOARD P CN704
D11 C-6
D12 D-6 A
D13 F-6
D14 C-7
JW31
D15 C-7 R33
D16 C-6 R32
D17 C-6 R24
PH11

FH1
D31 F-10

R10
CN31
2 1

C15

C16

C18
JW13
D32 D-9 CN1 1 5

C13

C14
R14

R15
D33 B-9
D34 B-9
B Q F1 R17
IC11 B-6
SUB POWER C1 R16

D34
D33
BOARD

R13
PH11 B-7 NO991
H
(Page 46) IC11 C17
C19 C25 MAIN
Q11 E-6

FH2
BOARD
CN201
Q12 F-6 CN32
R2
1 2 (Page
C32 31)

R12
K A D17 D14

C20 JW32
D15
C C21

R22
T1

R21
A K D16 JW33

D11

R25
(CHASSIS)

D32
D R19
R23 TK2

R18
TH1 HT3
D12 K A

C53

C52

C51
G S
T2 HT1 Q11
T31
MAIN POWER
TRANSFORMER

D
E

C23
C11

C3 R20 C31
C24 T81
D13 K A

G S
HT2
D1 Q12

F JW1

JW2 JW4
D
JW3
JW12 D31

C5 C22 JW11

FB11

C4 C26

G
TK1

11
(CHASSIS)
1-871-835- (11)

HCD-CPZ1DAB
44 44
 HCD-CPZ1DAB

7-27. SCHEMATIC DIAGRAM – SW POWER Board – • See page 53 for IC Pin Function Description.

D1
D3SB60F3

Q CN1
2P
F1
T3.15AL
T1 T2

C3
0.1
C4
470p
LIVE R2 C1 275V 250V
H250V
1M 0.22
NEUTRAL 1/2W 275V C5
470p
250V
(Page 47)

TK1
TH1

(CHASSIS) T31
C11
100
450V
R12
470k
R13
470k
R22 FB11
MAIN POWER
TRANSFORMER
CN32
2P H
POWER CONTROL 1k 16V
1.1µH
IC11 GND
R14 8.2k CXD9841P

C13 0.01 (Page 32)

VSENSE VD
D31 C31
C22 FCQ10A04 470
Q12
2SK3563(LB2SONY) 220p 25V
F/B 1kV
CN31
SWITCHING
R21 D13 5P
10 UDZW15B
C14 0.001
CT VG(H) GND

R15 15k
RT VS
D17
RB751V-40TE-17
R20
10k
S
28V

GND
P
R10 100k
C21 D16
28V
0.22 UDZW15B
GND VB GND
C23 C24
D11
UF4005PKG23 Q11 220p 27000p C32 (Page 35)
D32
C15 22 50V 2SK3563(LB2SONY) 1kV 800V FCH10A10 2200
TIMER 35V
SWITCHING C51 1
R19 D12 TK2
10 UDZW15B
C16 4.7 50V
SS VG(L) C52 1
R23 C26
0.1 1000p (CHASSIS)
2W 125V C53 1
C18 0.1 S
VC1 P-GND
C20
R18 R25
47
C17 0.001 25V 10k 33
OCP VC2
D14
R17 C19 D15 D1NL20U-TR
68 0.01 UDZW15B
R16 100
D33 D34
PH11 MTZJ27B MTZJ16A
PC123Y22J00F
C25
R24 100 ISOLATOR
1k
35V

R32
R33
1k 470

HCD-CPZ1DAB
45 45
HCD-CPZ1DAB
Ver. 1.1

7-28. PRINTED WIRING BOARD – SUB POWER Board – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

• Semiconductor
Location 1 2 3 4 5
Ref. No. Location
D991 B-4
D992 C-4
D993 C-5
D994 D-5 SUB POWER BOARD
D995 D-4

IC991 B-5
A
1
Q991 A-4 R992 R991
L
E 3
RY990 MAIN
Q991 BOARD
NO992 CN300

C991
C994 (Page 31)

JW992
2

JW990
5 4
B Q NO991 K
IC991
D991
C995
SW POWER 1 3
BOARD A
CN1 1
C993
(Page 44)

C992
RY991

C
T991
2 MAIN POWER

D992

D993
TRANSFORMER
CN990

JW995
(AC IN)
1

D
JW997

D995

D994
E
12, 13
1-870-844- (12), (13)

HCD-CPZ1DAB
46 46
 HCD-CPZ1DAB

7-29. SCHEMATIC DIAGRAM – SUB POWER Board – • See page 48 for IC Block Diagrams.

Q LIVE

NEUTRAL

C992
RY991
NO991 0.01
2P 250V
(Page 45)
D991 JW990 Q991
1SS355W 2SC3052F
RELAY DRIVE

C991
0.01
250V RY990 R991
2.2k

T991

VI

VO
SUB POWER

NOISE
CONT
TRANSFORMER

GND
JW995 +4V REGULATOR
CN990 D995 D992 IC991
2P 1N4002T 1N4002T MM1614ANLE
JW997 NO992

(AC IN)
LIVE

NEUTRAL
D994
1N4002T
D993
1N4002T C995 C994 R992
3P

RELAY ON
L
C993
0.01 1 100k 4V(EVER)
2200
16V
GND
JW992
(Page 33)

HCD-CPZ1DAB
47 47
 HCD-CPZ1DAB

• Waveforms • IC Block Diagrams

– CD Board – – TC Board – – AMP Board – – CD Board –
IC203 BH18LB1WG-TR
IC201 1 (LRCK), 2 (LRCKI) T601 4 IC701 qg (SCKI)
1 (CD PLAY mode)
qa (TAPE REC mode)
ea
VIN 1

THERMAL
PROTECTION

3.3 Vp-p 230 Vp-p 3.1 Vp-p OVER CURRENT

PROTECTION
22.8 µs 11 µs 81.5 ns
VOLTAGE –
1 V/DIV, 10 µs/DIV 50 V/DIV, 5 µs/DIV 1 V/DIV, 50 ns/DIV GND 2
REFERENCE +
5 VOUT
IC201 5 (BCK), 6 (BCKI) Q642, 643 (Collector) IC701 qa (BCK) CONTROL
2 (CD PLAY mode)
qs (TAPE REC mode)
es STBY 3
BLOCK 4 NC

3.3 Vp-p 18 Vp-p 3.3 Vp-p IC402 BA5947FM-E2

472 ns 11 µs 324 ns

CH3OUTR

CH4OUTR
CH4CAPA
OUTVREF

CH3OUTF

CH4OUTF
POWVCC
PREVCC

CH3RIN
CH3FIN
OPOUT

CH4IN

MUTE
5 V/DIV, 5 µs/DIV

GND
1 V/DIV, 200 ns/DIV 1 V/DIV, 100 ns/DIV
28 27 26 25 24 23 22 21 20 19 18 17 16 15
IC201 u; (RFACO) Q642, 643 (Base) IC701 q; (LRCK)
3 (CD PLAY mode)
qd (TAPE REC mode)
ed
MUTING D D D D

3.4 Vp-p + –
Approx. 3.8 Vp-p INTERFACE
20.8 µs
900 mVp-p 11 µs
200 mV/DIV, 500 ns/DIV 1 V/DIV, 5 µs/DIV 1 V/DIV, 10 µs/DIV LEVEL SHIFT

IC201 <z/, (XTAO) IC705 rk (XFSOIN) INTERFACE

4 ef
(CD PLAY mode)
INTERFACE

+ –
2.3 Vp-p 1.4 Vp-p VREF D D D D
59 ns 20.6 ns

1 V/DIV, 20 ns/DIV – MAIN Board – 500 mV/DIV, 10 ns/DIV 1 2 3 4 5 6 7 8 9 10 11 12 13 14

SW

CH1FIN

CH1RIN

CH2FIN

CH2RIN

GND

VREFIN

POWVCC

CH2OUTR

CH2OUTF

CH1OUTR

CH1OUTF
OPIN–
OPIN+
IC301 qa (XCOUT)
wa

2.7Vp-p
30.6 µs
– DRIVER Board – – DAB Board –
1 V/DIV, 10 µs/DIV IC801 BD33KA5WFP-E2
IC701 BA6956AN
IC805 BA50BC0WFP-E2
IC301 qd (XOUT)
ws
TSD VDD

VREF –
+ DRIVER

CONTROL LOGIC
880mVp-p
62.4 ns 1 2 3 4 5 6 7 8 9 THERMAL OVER CURRENT
SHUT DOWN PROTECT
VREF

OUT2

RNF

OUT1

VM

VCC

FIN

GND

RIN

500 mV/DIV, 20 ns/DIV

1 2 3 4 5

CTL

VCC

GND

OUT

NC
HCD-CPZ1DAB
48 48
 HCD-CPZ1DAB

– MAIN Board – IC421 MC14052BF

IC302 PST3629NR
2X0 1 16 VDD
OUT 1
15 X2
VDD 2 5 CD 2X2 2

2XCOM 3 14 X1

– 13 XCOM
2X3 4
+
12 X0
2X1 5

VREF 4 NC
INH 6 11 X3

VEE 7 10 A
GND 3

VSS 8 9 B

IC501 BD3872FS
SOUT1

SOUT2

BOUT1

BOUT2

OUT1

OUT2
SEQ1

SEQ2

BNF1

BNF2
TNF1

TNF2

CAP

VCC

SC
SI
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17

LOUD LOUD
SPEAKER SPEAKER
EQUALIZER1 EQUALIZER2
LOGIC
TREBLE1 BASS1
fo = 10 kHz fo = 80 Hz

TREBLE2 BASS2
fo = 10 kHz fo = 80 Hz

SURROUND

100k 100k 100k 100k 100k 100k 100k 100k 100k 100k

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
VIN1

SEL1

VIN2

SEL2

A1

A2

B1

B2

C1

C2

D1

D2

E1

E2

FILTER

GND

49
HCD-CPZ1DAB

– AMP Board –
IC701 PCM1802DBR

SINGLE-END/ 5TH ORDER 20 MODE1

VINL 1 DIFFERENTIAL DELTA-SIGMA
CONVERTER MODULATOR 19 MODE0
VINR 2 18 FMT1
x16 1/64 17 FMT0
(x1/128) SERIAL 16 OSR
VREF1 3 DECIMATION INTERFACE 15 SCKI
REFERENCE FILTER &
VREF2 4 WITH MODE/FORMAT 14 VDD
DC CUT CONTROL 13 DGND
FILTER 12 DOUT
11 BCK
SINGLE-END/ 5TH ORDER
DIFFERENTIAL DELTA-SIGMA
CONVERTER MODULATOR

VCC 5 POWER
AGND 6 SUPPLY

CLOCK & TIMING CONTROL

PDWN 7
BYPAS 8
FSYNC 9
LRCK 10

IC704 NJM2871BF18-TE2
VOUT
VIN

5 4

THERMAL
PROTECTION

BANDGAP
REFERENCE

1 2 3
CONTROL

GND

NOISE
BYPASS

50
 HCD-CPZ1DAB

IC705 CXD9788AR

HPOUTR1

HPOUTR2
HPOUTL1

HPOUTL2

HPVDDR
HPVDDL

HPVSSR

FSOCKO
HPVSSL
XFSOIN

XVDD

FSOI
48 47 46 45 44 43 42 41 40 39 38 37

CLOCK CLOCK
GENERATOR GENERATOR 36 XFSIIN
(SECONDARY) (PRIMARY)
XVSS 1 35 DVDD
VSUBC 2 34 TEST

VSSR 3 33 BFVSS

OUTR2 4 32 BFVDD
VDDR 5
PWM
OUTR1 6 FILTER & SAMPLING 31 DATA
LINER GAIN
∆Σ LOW CUT RATE SgP 30 BCK
VSSR 7 INTERPOLATOR CONTROL FILTER CONVERTER 29 LRCK

VSSL 8
28 MCKSEL
OUTL2 9
27 INIT
VDDL 10
INIT/ SERIAL 26 SFLAG
OUTL1 11
MUTE CONTROLLER
25 OVFFLAGL
VSSL 12

13 14 15 16 17 18 19 20 21 22 23 24
XOVSS

XFSOOUT

XOVDD

DVDD

DVSS

NSPMUTE

SOFTMUTE

PGMUTE

SCDT

SCSHIFT

SCLATCH

OVFFLAGR

51
HCD-CPZ1DAB

IC707, 708 CXD9774M

36 GVDD B
GVDD 35 GVDD B
34 GND
33 BST B

DVDD DREG DREG OCH

GND 1
32 PVDD B
PWM GATE
PWM BP 2 31 PVDD B
RECEIVER DRIVE
TIMING 30 OUT B
GND 3
CONTROL 29 OUT B
DGND
&
RESET 4 PROTECTION 28 GND
GATE
DREG RTN 5 DRIVE

DIGITAL OCL
DREG
REGULATOR

GVDD 6 GVDD

M3 7

DREG 8 DREG

DGND 9

M1 10
M2 11 PROTECTION
LOGIC
DVDD 12
OT
SD 13 & OCL
UVP
DGND 14 GATE
DRIVE
OTW 15 TIMING 27 GND
CONTROL
DVDD DREG
& 26 OUT A
GND 16 PROTECTION 25 OUT A
PWM GATE
PWM AP 17 24 PVDD A
RECEIVER DRIVE
23 PVDD A
GND 18
DGND DREG OCH

22 BST A
21 GND
GVDD 20 GVDD A
19 GVDD A

– SUB POWER Board –

IC991 MM1614A
VOUT
VIN

5 4

CURRENT
BIAS
LIMITTER

REFERENCE –
DRIVER
+

THERMAL
SHUTDOWN

1 2 3
CONT

GND

NOISE

52
 HCD-CPZ1DAB

• IC Pin Function Description

CD BOARD IC201 CXD3014A-201R (CD DSP)
Pin No. Pin Name I/O Description
1 LRCK O L/R sampling clock signal output terminal
2 LRCKI I L/R sampling clock signal input terminal
3 PCMD O Serial data output terminal
4 PCMDI I Serial data input terminal
5 BCK O Bit clock signal output terminal
6 BCKI I Bit clock signal input terminal
Oscillation circuit on/off control signal input from the system controller
7 XTACN I
"L": oscillation stop, "H": self-oscillation
8 XRST I System reset signal input from the system controller "L": reset
9 VSS - Ground terminal
10 IREQ-MP3 O MP3 data request signal output to the system controller
11 CLOK I CD serial data transfer clock signal input from the system controller
12 DATA2 I MP3 serial data input from the system controller
13 XLAT-MP3 I MP3 serial data latch pulse signal input from the system controller
14 REQ-MP3 I MP3 data request signal input from the system controller
15 ACK-MP3 O MP3 acknowledge signal output to the system controller
16 XLAT I CD serial data latch pulse signal input from the system controller
17 VDD - Power supply terminal (+1.8V)
18 SVSS - Ground terminal
19 SVDD - Power supply terminal (+1.8V)
20 SENS O Internal status (SENSE) signal output to the system controller
21 WFCK O Write frame clock signal output terminal Not used
22 XUGF O XUGF signal output terminal Not used
23 XPCK O XPCK signal output terminal Not used
24 GFS O Guard frame sync signal output terminal Not used
25 C2PO O C2 pointer signal output terminal Not used
26 SCOR O Subcode sync (S0+S1) detection signal output to the system controller
27 VDD - Power supply terminal (+1.8V)
28 COUT O Numbers of track counted signal output terminal Not used
29 SVSS - Ground terminal
30 SVDD - Power supply terminal (+1.8V)
31 MIRR O Mirror signal output terminal Not used
32 DFCT O Defect signal output terminal Not used
33 FOK O Focus OK signal output terminal Not used
34 VSS - Ground terminal
35 VDD - Power supply terminal (+1.8V)
36 VSS - Ground terminal
37 LOCK O GFS is sampled by 460 Hz "H" output when GFS is "H" Not used
38 MDP O Spindle motor servo control signal output terminal
39 SSTP I Disc inner position detection signal input terminal
40 IOVSS1 - Ground terminal
41 SFDR O Sled servo drive signal (+) output terminal
42 SRDR O Sled servo drive signal (-) output terminal
43 TFDR O Tracking servo drive signal (+) output terminal
44 TRDR O Tracking servo drive signal (-) output terminal
45 FFDR O Focus servo drive signal (+) output terminal

53
HCD-CPZ1DAB

Pin No. Pin Name I/O Description

46 FRDR O Focus servo drive signal (-) output terminal
47 IOVDD1 - Power supply terminal (+3.3V)
48 AVDD0 - Power supply terminal (+3.3V)
49 AVSS0 - Ground terminal
50 E I E signal input from the optical pick-up block
51 F I F signal input from the optical pick-up block
52 TEI I Tracking error signal input terminal
53 TEO O Tracking error signal output terminal
54 FEI I Focus error signal input terminal
55 FEO O Focus error signal output terminal
56 VC O Middle point voltage output terminal
57 A I A signal input from the optical pick-up block
58 B I B signal input from the optical pick-up block
59 C I C signal input from the optical pick-up block
60 D I D signal input from the optical pick-up block
61 AVDD4 - Power supply terminal (+3.3V)
62 RFDCO O RFDC signal output terminal Not used
63 PDSENS I Reference voltage input terminal for PD
64 AC_SUM O RFAC summing amplifier signal output terminal
65 EQ_IN I RF equalizer circuit input terminal
Laser diode on/off control signal output to the automatic power control circuit
66 LD O
"H": laser diode on
67 PD I Light amount monitor input from the laser diode of optical pick-up block
68 RFC I Equalizer cut off frequency adjustment terminal
69 AVSS4 - Ground terminal
70 RFACO O EFM signal output terminal
71 RFACI I EFM signal input terminal
72 AVDD3 - Power supply terminal (+3.3V)
73 BIAS I Asymmetry circuit constant current input terminal
74 ASYI I Playback EFM asymmetry comparator voltage input terminal
75 ASYO O Playback EFM full-swing output terminal
76 VPCO O Charge pump output terminal for broad-band EFM PLL
77 VCTL I VCO2 control voltage input terminal for broad-band EFM PLL
78 AVSS3 - Ground terminal
79 CLTV I VCO1 control voltage input terminal for multiplier
80 FILO O Filter output terminal for master PLL
81 FILI I Filter input terminal for master PLL
82 PCO O Charge pump output terminal for master PLL
83 SVSS - Ground terminal
84 SVDD - Power supply terminal (+1.8V)
85 SSTB-MP3 I MP3 standby on/off control signal input terminal "L": standby Not used
86 VDD - Power supply terminal (+1.8V)
87 VSS - Ground terminal
88 TEST1 I Input terminal for the test Normally: fixed at "L"
89 DATA I CD serial data input from the system controller
90 CLK2 I MP3 serial data transfer clock signal input from the system controller
91 SVSS - Ground terminal

54
 HCD-CPZ1DAB

Pin No. Pin Name I/O Description

92 SVDD - Power supply terminal (+2.5V)
93 JTAGTCK I Clock signal input terminal (for JTAG) Not used
94 JTAGTDI I Data input terminal (for JTAG) Not used
95 JTAGTDO O Data output terminal (for JTAG) Not used
96 JTAGTMS I Mode select signal input terminal (for JTAG) Not used
97 TRST I Reset signal input terminal (for JTAG) Not used
98 VSS - Ground terminal
99 VDD - Power supply terminal (+1.8V)
100 IOVDD2 - Power supply terminal (+3.3V)
101 DOUT O Digital audio signal output terminal
102 TEST I Input terminal for the test Normally: fixed at "L"
103 TES1 I Input terminal for the test Normally: fixed at "L"
104 IOVSS2 - Ground terminal
105 PLLVDD - Power supply terminal (+1.8V)
106 PLLVSS - Ground terminal
107 XVSS - Ground terminal
108 XTAO O System clock output terminal (16.9344 MHz)
109 XTAI I System clock input terminal (16.9344 MHz)
110 XVDD - Power supply terminal (+1.8V)
111 AVDD1 - Power supply terminal (+3.3V)
112 AOUT1 O L-ch analog audio signal output terminal
113 VREFL O L-ch reference voltage output terminal
114 AVSS1 - Ground terminal
115 AVSS2 - Ground terminal
116 VREFR O R-ch reference voltage output terminal
117 AOUT2 O R-ch analog audio signal output terminal
118 AVDD2 - Power supply terminal (+3.3V)
119 IOVDD0 - Power supply terminal (+3.3V)
120 IOVSS0 - Ground terminal

55
HCD-CPZ1DAB

MAIN BOARD IC301 M30624MGP-A59FPU0 (SYSTEM CONTROLLER)

Pin No. Pin Name I/O Description
POWER
1 I AC input detection terminal
PROTECT2
2 ST MUTE O Tuner muting on/off control signal output terminal "H": muting on
3 DR MUTE O System reset signal output to the motor/coil driver "L": reset
4 SIRCS I Remote control signal input terminal
5 MP3 DATA OUT O MP3 serial data output to the CD DSP
6 MP3 DATA IN I MP3 serial data input from the CD DSP
7 MP3-CLK O MP3 serial data transfer clock signal output to the CD DSP
8 BYTE I External data bus line byte selection signal input fixed at "L"
9 CNVSS - Processor mode switch terminal (for test)
10 XCIN I Sub system clock input terminal (32.768 kHz)
11 XCOUT O Sub system clock output terminal (32.768 kHz)
System reset signal input terminal "L": reset
12 RESET I
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
13 XOUT O Main system clock output terminal (10 MHz)
14 VSS - Ground terminal
15 XIN I Main system clock input terminal (10 MHz)
16 VCC - Power supply terminal (+3.3V)
17 NMI I Non-maskable interrupt input terminal Not used
18 RDS INT I Interrupt status input from the RDS decoder on the tuner unit
19 CD SCOR I Sub-code sync (S0+S1) detection signal input from the CD DSP
20 AC CUT I AC detection signal input terminal "L": AC off
21 ST CLK O PLL serial data transfer clock signal output to the tuner unit
22 ST DATA IN I PLL serial data input from the tuner unit
23 ST DATA OUT O PLL serial data output to the tuner unit
24 ST CE O PLL serial chip enable signal output to the tuner unit
25 TUNED IN I Tuning detection signal input from the tuner unit
26 RDS DATA I Serial data input from the RDS decoder on the tuner unit
27 TC TRG O Trigger plunger on/off control signal output "H": plunger on
28 TC CAPM CNT1 O TC capstan motor drive signal output terminal
29 IIC CLK I/O IIC data reading clock signal input or transfer clock signal output terminal Not used
30 IIC DATA I/O IIC two-way data bus terminal Not used
31 DAB-DO O Serial data output to the DAB tuner module
32 DAB-DI I Serial data input from the DAB tuner module
33 TC PB/REC SW O Playback/record selection signal output "L": playback, "H": record
34 TC LINE MUTE O Line muting on/off selection signal output to the REC/PB AMP
35 LCD DATA O Serial data output to the LCD
36 LCD-CLK O Serial data transfer clock signal output to the LCD
37 CD CLK I CD serial data transfer clock signal input from the CD DSP
38 TC REC MUTE O Recording muting on/off control signal output terminal
39 ALC O Automatic limiter control signal output terminal
40 S-MASTER INIT O Initialize signal output to the stream processor
S-MASTER
41 O NSP muting on/off signal output to the stream processor
NSP MUTE
42 S-MASTER LATCH O Serial data latch pulse signal output to the stream processor
43 S-MASTER SHIFT O Shift clock signal output to the stream processor

56
 HCD-CPZ1DAB

Pin No. Pin Name I/O Description

44 S-MASTER DATA O Serial data output to the stream processor
45 S-MASTER SD I Shut down state input from the power driver "L": shut down
46 S-MASTER RST O Reset signal output to the power driver
S-MASTER
47 O Soft muting on/off control signal output to the stream processor
SOFT MUTE
S-MASTER
48 O Reset signal output to the stream processor
PG MUTE
49 LCD_ON O LED brightness control signal for LCD backlight output terminal
50 AMP SC O Serial data transfer clock signal output to the electrical volume
51 AMP SI O Serial data output to the electrical volume
52 LINE MUTE O Line muting on/off selection signal output terminal
53 HP MUTE O Headphone muting on/off selection signal output terminal
54 HP DET I Headphone detection signal input terminal "H": headphone on
55 STEREO IN I FM stereo detection signal input from the tuner unit "L": stereo
56 DAB-POWER3.3 O Power on/off control signal output for DAB (+3.3V) output terminal
57 DAB-POWER5.0 O Power on/off control signal output for DAB (+5V) output terminal
58 DAB-MUTE O Tuner switching signal output terminal (FM/AM or DAB)
DAB
59 O Tuner switching signal output terminal (FM/AM or DAB)
SELECTOR SW

60 CD DATA O CD serial data output to the CD DSP

61 CD SENS I SENS signal input from the CD DSP
62 VCC - Power supply terminal (+3.3V)
63 LCD RESB O Reset signal output to the LCD
64 VSS - Ground terminal
65 LED TAPE O LED drive signal output terminal "H": tape function
66 LED TUNER O LED drive signal output terminal "H": tuner function
67 LED CD O LED drive signal output terminal "H": CD function
68 VOLUME A I Jog dial pulse input from the rotary encoder for the VOLUME (A phase input)
69 VOLUME B I Jog dial pulse input from the rotary encoder for the VOLUME (B phase input)
70 FOLDER A I Jog dial pulse input from the rotary encoder (A phase input)
71 FOLDER B I Jog dial pulse input from the rotary encoder (B phase input)
72 LED STAND BY O LED drive signal output terminal "H": standby
73 TC PLAY I Tape play detection switch input terminal "L": tape play mode
74 WAKE UP KEY I Key interruption processing start signal input terminal
75 TC BIAS ON O Recording bias on/off control signal output terminal "H": bias on
CDM SW2
76 I Detection input from the chuck switch "L": loading in
(CLOSE)
CDM SW1
77 I Detection input from the out switch "L": loading out
(OPEN)
78 LCD CS O Chip select signal output to the LCD driver
79 CDM LOAD OUT O CD loading motor control signal (eject direction) output terminal "H" active
80 CDM LOAD IN O CD loading motor control signal (loading direction) output terminal "H" active
CD POWER
81 O CD power on/off control signal output terminal "H": power on
ON/OFF
Oscillation circuit on/off switch control signal output to the CD DSP
82 CD XTACN O
"H": self-oscillation, "L": oscillation stop
83 CD XRST O Reset signal output to the CD DSP "L": reset
84 MP3 IREQ O MP3 data request signal output to the CD DSP

57
HCD-CPZ1DAB

Pin No. Pin Name I/O Description

85 MP3 XLAT O MP3 serial data latch pulse output to the CD DSP
86 MP3 REQ O MP3 chip select signal output to the CD DSP
87 MP3 ACK O MP3 acknowledge signal output to the CD DSP
88 CD XLAT O CD serial data latch pulse output to the CD DSP
89 TREBLE I Jog dial pulse input from the rotary encoder for the treble
90 BASS I Jog dial pulse input from the rotary encoder for the bass
91 TC END SW I Tape end detect sensor input terminal "H" input when the tape end detected
TC HALF/REC Cassette in and recording direction detection signal input terminal
92 I
SW "L": side B recording, center voltage: cassette in (stop), "H": side A recording
93 SPEC IN I Destination setting terminal
94, 95 KEY2, KEY1 I Key input (A/D input) terminal for the front panel
96 AVSS - Ground terminal
97 KEY0 I Key input (A/D input) terminal for the front panel
98 VREF I Reference voltage (+3.3V) input terminal
99 AVCC - Power supply terminal (+3.3V)
POWER RELAY
100 O Main power on/off relay drive signal output terminal "H": relay on
ON/OFF

58
 HCD-CPZ1DAB

SW POWER BOARD IC11 CXD9841P (POWER CONTROL)

Pin No. Pin Name I/O Description
1 VSENSE I AC line voltage detection terminal
2 F/B I Feed back signal input terminal for frequency modulation of oscillator
3 CT I Connected to the external capacitor for oscillator duty/frequency setting
4 RT I Connected to the external resistor for oscillator frequency setting
5 GND - Ground terminal
Connected to the external capacitor for determines intermittent operation period when abnormal
6 TIMER I
detection state
7 SS I Connected to the external capacitor for soft start timing
8 VC1 I Power supply terminal for control circuit "L": stop
9 OCP I Over current detection terminal
10 VC2 O Power supply output terminal for driver
11 PGND - Ground terminal for low voltage side driver
12 VG (L) O Low voltage side driver drive signal output terminal
13 - - Not used
14 VG O Power supply output terminal for high voltage side driver
15 VS I High voltage side driver reference voltage input terminal
16 VG (H) O High voltage side driver drive signal output terminal
17 - - Not used
Terminal for drain-kick starting When starting, current is supplied directly from the rectification
18 VD I
diode to VC1

59
HCD-CPZ1DAB
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark
may have some difference from the original are seldom required for routine service. Some 0 or dotted line with mark 0 are
one. delay should be anticipated when ordering critical for safety.
• Color Indication of Appearance Parts these items. Replace only with part number
Example: • The mechanical parts with no reference specified.
KNOB, BALANCE (WHITE) . . . (RED) number in the exploded views are not supplied.
↑ ↑
Parts Color Cabinet's Color

8-1. CASE SECTION

1 3

#1

4
chassis section

mechanical deck (tape) section

4 3

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 2-584-652-02 CASE 4 4-233-372-02 FOOT (FELT)
2 3-363-099-11 SCREW (CASE 3 TP2) #1 7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S
3 3-252-829-01 SCREW (B3), (+) BV TAPPING

60
 HCD-CPZ1DAB

8-2. MECHANICAL DECK (TAPE) SECTION

FFC301
not supplied 65
FFC601

#2

65

62 #2
not supplied
(TC board)

lid (TC) section

57
54 56
53

55
58
59
60
58
52
61

51

flont panel section

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 2-514-661-01 COVER (AZIMUTH) 60 2-588-354-01 LEVER (TC LOCK)
52 2-023-740-01 SPRING (LID TC2), TORSION
53 2-514-677-01 BUTTON (TC-EJECT) 61 4-244-530-01 DAMPER
54 2-514-684-01 LEVER (EJECT) 62 1-796-456-41 DECK, MECHANICAL (CMAL1Z255A)
55 2-595-751-01 SPRING (TC-EJECT), COIL 65 3-669-480-51 +PTPWH 2
FFC301 1-831-950-21 CABLE, FLEXIBLE FLAT (19 CORE)
56 3-254-151-01 SCREW (B2.6), (+) P TAPPING FFC601 1-831-992-11 CABLE, FLEXIBLE FLAT (8 CORE)
57 2-514-660-02 COVER (EJECT)
58 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
59 2-588-394-02 SPRING (TC LOCK)

61
HCD-CPZ1DAB

8-3. FRONT PANEL SECTION

112

not supplied
(PANEL board)
113 112
106
119

not supplied
(HP/MD board) 111
not supplied 107 112
not supplied

112
108
112 FFC901

not supplied
115 (OPT board)
116
112
105

not supplied
104 (SUB PANEL board)
112

103 102 112

114 101

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 2-514-665-11 KNOB (UD) 112 3-254-151-01 SCREW (B2.6), (+) P TAPPING
102 2-514-654-02 LID (MD LINK)
103 2-514-664-01 KNOB (VOL) 113 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING
104 2-514-663-01 KNOB (TRE) 114 2-514-656-01 SHAFT (LID MD)
105 2-514-662-01 KNOB (BASS) 115 2-514-688-01 SPRING (LID MD)
116 3-254-058-01 SCREW
106 X-2149-307-1 PANEL (SERVICE) ASSY, FRONT 119 2-632-228-01 SHEET (RIMOKON)
107 2-514-671-01 BUTTON (DSGX)
108 2-514-672-01 BUTTON (FOLDER) FFC901 1-831-952-21 CABLE, FLEXIBLE FLAT (19 CORE)
111 2-514-666-02 BRACKET (TC)

62
 HCD-CPZ1DAB

8-4. LID (TC) SECTION

156
156

155

D951,D952

152 155
157
not supplied
(LCD board)

not supplied

LCD951

not supplied
not supplied
151

FFC951

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 X-2149-308-1 LID (SERVICE) ASSY D951 6-501-138-01 LED SELU2WA10C-LF62 (LCD BACK LIGHT)
152 2-687-696-01 HOLDER (LCD) D952 6-501-138-01 LED SELU2WA10C-LF62 (LCD BACK LIGHT)
155 3-254-151-01 SCREW (B2.6), (+) P TAPPING FFC951 1-832-806-21 CABLE, FLEXIBLE FLAT (7 CORE)
156 2-584-676-01 SPRING (TC), PLATE LCD951 1-802-192-11 DISPLAY PANEL, LIQUID CRYSTAL
157 4-252-353-04 HOLDER (TC)

63
HCD-CPZ1DAB

8-5. CHASSIS SECTION

AMP/power section
not supplied not supplied
203 #2

not supplied

#1 #2

not supplied

#1
MAIN board
#1
FFC308
not supplied
201
CD mechanism deck section-1
(CDM80BH-K6BD83S-WD) 205
202 FFC309 207

not supplied
not supplied
#1
not supplied
205

not supplied
205
not supplied #1
not supplied

208

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
0 201 1-751-520-31 CORD, POWER 208 3-254-143-01 SCREW (B3), (+) BV TAPPING
202 3-703-244-00 BUSHING (2104), CORD FFC308 1-832-756-21 CABLE, FLEXIBLE FLAT (23 CORE)
203 A-1193-279-A MAIN BOARD, COMPLETE FFC309 1-831-943-21 CABLE, FLEXIBLE FLAT (15 CORE)
205 3-252-829-01 SCREW (B3), (+) BV TAPPING #1 7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S
207 1-693-626-11 TUNER (FM/AM) #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

64
 HCD-CPZ1DAB
Ver. 1.1

8-6. AMP/POWER SECTION

not supplied
(SW POWER board)

F1

259
#1
not supplied
(SP board)
#1
FFC302

254
not supplied
253 not supplied
#1

#1 258
#2
not supplied
supplied with 252

not supplied 260

(SUB POWER board)

252

255 CN3
not supplied
251

#1

FFC310

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 A-1193-284-A DAB BOARD, COMPLETE 260 1-500-082-21 CLAMP, SLEEVE FERRITE
252 1-830-386-21 CORD (WITH CONNECTOR) (for Venice 1.1) CN3 1-815-550-11 PIN, CONNECTOR (PWB) 2P
253 A-1193-293-A AMP BOARD, COMPLETE 0 F1 1-576-230-51 FUSE (H.B.C) (T3.15AL/H250V)
254 1-400-932-11 FILTER, CLAMP
255 1-478-669-11 MODULE (DAB TUNER) (Venice 1.1) FFC302 1-832-874-21 CABLE, FLEXIBLE FLAT (21 CORE)
FFC310 1-832-816-21 CABLE, FLEXIBLE FLAT (9 CORE)
258 2-514-691-01 SHEET, RADIATION #1 7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S
259 3-254-142-01 SCREW (B3), (+) BV TAPPING #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

65
HCD-CPZ1DAB

8-7. CD MECHANISM DECK SECTION-1

(CDM80BH-K6BD83S-WD)
410

410 411

#9
410

412
410

CD mechanism deck section-2

(CDM80BH-K6BD83S-WD) M701
401
409
407 B
A
408
406

405

CD mechanism deck section-3

(CDM80BH-K6BD83S-WD)

404 B

401
A
#8

403 414

base unit section

(BU-K6BD83S-WD)

401

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
401 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 410 3-087-053-01 +BVTP2.6 (3CR)
403 4-245-653-11 BELT (MOT) 411 4-245-639-01 LEVER (CL UP2)
404 4-245-662-02 PULLEY (GEAR)
405 4-245-646-01 GEAR (IDL-F) 412 1-688-337-11 DRIVER BOARD
406 4-245-644-01 GEAR (IDL-D) 414 2-515-538-01 SPRING (HOLDER DOWN B), COIL
M701 A-1148-845-A MOTOR ASSY (LOADING)
407 4-245-645-01 GEAR (IDL-E) #8 7-623-921-01 WASHER 1.7, NYLON
408 4-246-203-01 LEVER (RELEASE) #9 7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT
409 4-245-630-01 LEVER (SW)

66
 HCD-CPZ1DAB

8-8. CD MECHANISM DECK SECTION-2

(CDM80BH-K6BD83S-WD)

464
463

462

461
460 465

459
458
466

457 467

468
455
456
456 469
455
454

453
470
452
451
453
452
451

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
451 4-245-627-01 WASHER (6-2.7-0.4) 461 4-245-640-01 GEAR (CAP)
452 4-245-637-11 ROLLER, RUBBER 462 1-452-925-41 MAGNET ASSY
453 4-245-649-01 GEAR (IDL-I) 463 4-245-638-01 LEVER (CL UP1)
454 4-245-657-11 LEVER (LOADING-R) 464 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
455 4-245-647-01 GEAR (IDL-G) 465 4-245-636-01 SPR-T CL DOWN

456 4-245-648-01 GEAR (IDL-H) 466 4-245-658-11 LEVER (DISC STOP)

457 4-245-655-11 CHASSIS (TOP) 467 4-245-659-11 LEVER (DISC SENSOR)
458 4-245-631-11 SPT-T (LOADING-R) 468 4-245-632-11 SPR-T (LOADING-L)
459 4-245-650-01 GEAR (IDL-J) 469 X-2021-532-1 CLAMPER 213 ASSY
460 4-245-651-11 GEAR (IDL-L) 470 4-245-656-11 LEVER (LOADING-L)

67
HCD-CPZ1DAB

8-9. CD MECHANISM DECK SECTION-3

(CDM80BH-K6BD83S-WD)

510
509

508

507
511
506
512

505 513
509
504
514
516

503 not supplied

502

515

501

not supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
501 4-245-643-01 GEAR (IDL-C) 510 4-245-628-01 LEVER (BU LOCK)
502 X-4956-147-1 CHASSIS (BOTTOM) ASSY
503 2-515-536-01 SPRING (DIR), TENSION COIL 511 4-248-206-01 WASHER (3-1-0.4)
504 4-245-642-01 GEAR (IDL-B) 512 4-245-624-01 LEVER, CLOSE
505 4-245-814-01 LEVER (DIR FIRST) 513 4-245-635-01 SPR-E LEVER CLOSE
514 4-245-629-01 GEAR (BU LOCK)
506 2-515-534-01 SPRING (DIR BACK), TENSION COIL 515 4-245-644-01 GEAR (IDL-D)
507 4-245-660-11 LEVER (DIR)
508 4-245-641-01 GEAR (IDL-A) 516 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
509 4-245-640-01 GEAR (CAP)

68
 HCD-CPZ1DAB

8-10. BASE UNIT SECTION

(BU-K6BD83S-WD)

558

555

556 554
(including spindle motor (M401),
sled motor (M402))
560

555
555
554
554
not supplied
not supplied (sled motor (M402)) 560
553 (spindle motor (M401))
555
552
554

553

552
551 559

S201

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
551 A-1134-281-A CD BOARD, COMPLETE 0 556 A-4735-357-A OPTICAL PICK-UP BLOCK (KSM-213DHAP)
552 4-218-253-31 +BTTP M2.6 558 X-4956-146-1 HOLDER (BU215) ASSY
553 4-231-151-01 STOPPER (BU) 559 1-827-992-11 WIRE (FLAT TYPE) (16 CORE)
554 4-227-045-31 SPRING (INSULATOR), COIL 560 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
555 4-227-549-11 INSULATOR S201 1-771-853-11 SWITCH, DETECTION (LIMIT)

69
HCD-CPZ1DAB
SECTION 9
AMP
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark
parts list may be different from the parts are seldom required for routine service. 0 or dotted line with mark 0 are
specified in the diagrams or the components Some delay should be anticipated when critical for safety.
used on the set. ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS specified.
may have some difference from the original In each case, u: µ, for example:
one. uA... : µA... uPA... : µPA... When indicating parts by reference
• RESISTORS uPB... : µPB... uPC... : µPC... number, please include the board.
All resistors are in ohms. uPD... : µPD...
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF
F: nonflammable • COILS
uH: µH

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-1193-293-A AMP BOARD, COMPLETE
********************* C748 1-126-964-11 ELECT 10uF 20% 50V
C749 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< CAPACITOR/JUMPER RESISTOR > C750 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C751 1-126-961-11 ELECT 2.2uF 20% 50V
C701 1-126-961-11 ELECT 2.2uF 20% 50V C752 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C702 1-136-497-81 FILM 0.1uF 5% 50V
C703 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C753 1-126-933-11 ELECT 100uF 20% 16V
C704 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C754 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C706 1-100-717-91 CERAMIC CHIP 1uF 16V C756 1-100-717-91 CERAMIC CHIP 1uF 16V
C757 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C708 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C758 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C709 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C710 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C759 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C711 1-126-934-11 ELECT 220uF 20% 16V C761 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C712 1-100-717-91 CERAMIC CHIP 1uF 16V C762 1-100-717-91 CERAMIC CHIP 1uF 16V
C763 1-100-756-91 CERAMIC CHIP 0.047uF 50V
C713 1-100-756-91 CERAMIC CHIP 0.047uF 50V C764 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V
C714 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V
C715 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V C765 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V
C716 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V C766 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V
C717 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V C767 1-125-898-11 CERAMIC CHIP 0.22uF 10% 50V
C768 1-100-756-91 CERAMIC CHIP 0.047uF 50V
C718 1-100-756-91 CERAMIC CHIP 0.047uF 50V C769 1-100-924-21 ELECT 2200uF 20% 35V
C719 1-100-924-21 ELECT 2200uF 20% 35V
C720 1-137-198-81 FILM 1uF 5% 50V C770 1-137-198-81 FILM 1uF 5% 50V
C722 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C772 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C723 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C773 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C774 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C724 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C775 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C725 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C726 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V C777 1-137-198-81 FILM 1uF 5% 50V
C728 1-137-198-81 FILM 1uF 5% 50V C778 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
C729 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C779 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C780 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C730 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C781 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C731 1-104-664-11 ELECT 47uF 20% 25V
C732 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C782 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C733 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C783 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C734 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C784 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C785 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C735 1-126-964-11 ELECT 10uF 20% 50V C786 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C737 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C738 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C787 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C739 1-162-916-11 CERAMIC CHIP 12PF 5% 50V C788 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C740 1-126-923-11 ELECT 220uF 20% 10V C791 1-136-497-81 FILM 0.1uF 5% 50V
C792 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C741 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C794 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C744 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C745 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C796 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C746 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C797 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C747 1-126-933-11 ELECT 100uF 20% 16V C798 1-126-933-11 ELECT 100uF 20% 16V

70
 HCD-CPZ1DAB
AMP

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C799 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C806 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V L708 1-456-813-11 COIL, AIR-CORE
L709 1-456-813-11 COIL, AIR-CORE
C813 1-165-908-11 CERAMIC CHIP 1uF 10% 10V L710 1-457-235-11 INDUCTOR 10uH
C827 1-165-908-11 CERAMIC CHIP 1uF 10% 10V L711 1-457-235-11 INDUCTOR 10uH
C828 1-165-908-11 CERAMIC CHIP 1uF 10% 10V L758 1-456-813-11 COIL, AIR-CORE
C829 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C830 1-165-908-11 CERAMIC CHIP 1uF 10% 10V L759 1-456-813-11 COIL, AIR-CORE
L760 1-457-235-11 INDUCTOR 10uH
C831 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V L761 1-457-235-11 INDUCTOR 10uH
C832 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C839 1-165-908-11 CERAMIC CHIP 1uF 10% 10V < TRANSISTOR >
C840 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C841 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q701 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF
Q702 8-729-620-33 TRANSISTOR 2SA1235TP-1EF
C842 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V Q703 8-729-620-33 TRANSISTOR 2SA1235TP-1EF
C843 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q752 8-729-620-33 TRANSISTOR 2SA1235TP-1EF
C844 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V Q753 8-729-620-33 TRANSISTOR 2SA1235TP-1EF
C845 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C846 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V < RESISTOR >

C847 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V R701 1-216-864-11 SHORT CHIP 0
C848 1-216-864-11 SHORT CHIP 0 R704 1-216-864-11 SHORT CHIP 0
C849 1-216-864-11 SHORT CHIP 0 R706 1-216-809-11 METAL CHIP 100 5% 1/10W
R707 1-216-864-11 SHORT CHIP 0
< CONNECTOR > R708 1-216-864-11 SHORT CHIP 0

CN700 1-784-782-11 CONNECTOR, FFC 21P R709 1-216-864-11 SHORT CHIP 0

* CN704 1-564-508-11 PLUG, CONNECTOR 5P R711 1-216-809-11 METAL CHIP 100 5% 1/10W
R712 1-216-809-11 METAL CHIP 100 5% 1/10W
< DIODE > R713 1-216-837-11 METAL CHIP 22K 5% 1/10W
R714 1-216-817-11 METAL CHIP 470 5% 1/10W
D701 6-501-193-01 DIODE 1SS355WTE-17
D702 6-501-193-01 DIODE 1SS355WTE-17 R716 1-216-821-11 METAL CHIP 1K 5% 1/10W
D703 6-501-193-01 DIODE 1SS355WTE-17 R717 1-216-821-11 METAL CHIP 1K 5% 1/10W
D704 6-501-193-01 DIODE 1SS355WTE-17 R718 1-216-833-11 METAL CHIP 10K 5% 1/10W
D705 6-500-260-01 DIODE P6SMB39AT3 R719 1-220-942-11 METAL CHIP 3.3 1% 1/4W
R720 1-220-942-11 METAL CHIP 3.3 1% 1/4W
D706 6-500-260-01 DIODE P6SMB39AT3
D713 6-501-159-01 DIODE UDZW-TE17-2.4B R721 1-216-833-11 METAL CHIP 10K 5% 1/10W
D755 6-500-260-01 DIODE P6SMB39AT3 R723 1-216-821-11 METAL CHIP 1K 5% 1/10W
D756 6-500-260-01 DIODE P6SMB39AT3 R724 1-216-793-11 METAL CHIP 4.7 5% 1/10W
R725 1-216-793-11 METAL CHIP 4.7 5% 1/10W
< EARTH TERMINAL > R726 1-216-849-11 METAL CHIP 220K 5% 1/10W

EP701 1-537-771-21 TERMINAL BOARD, GROUND R727 1-216-845-11 METAL CHIP 100K 5% 1/10W
EP702 1-537-771-21 TERMINAL BOARD, GROUND R728 1-216-849-11 METAL CHIP 220K 5% 1/10W
EP703 1-537-771-21 TERMINAL BOARD, GROUND R729 1-216-821-11 METAL CHIP 1K 5% 1/10W
EP705 1-537-771-21 TERMINAL BOARD, GROUND R730 1-216-809-11 METAL CHIP 100 5% 1/10W
EP706 1-537-771-21 TERMINAL BOARD, GROUND R731 1-216-813-11 METAL CHIP 220 5% 1/10W

< IC > R733 1-216-813-11 METAL CHIP 220 5% 1/10W

R734 1-216-864-11 SHORT CHIP 0
IC701 6-701-834-01 IC PCM1802DBR R736 1-216-857-11 METAL CHIP 1M 5% 1/10W
IC703 8-759-096-87 IC TC7WU04FU (TE12R) R737 1-216-821-11 METAL CHIP 1K 5% 1/10W
IC704 6-707-956-01 IC NJM2871BF18-TE2 R738 1-216-821-11 METAL CHIP 1K 5% 1/10W
IC705 6-705-979-01 IC CXD9788AR
IC707 6-704-802-01 IC CXD9774M R739 1-216-833-11 METAL CHIP 10K 5% 1/10W
R740 1-216-833-11 METAL CHIP 10K 5% 1/10W
IC708 6-704-802-01 IC CXD9774M R741 1-216-809-11 METAL CHIP 100 5% 1/10W
IC709 6-706-492-01 IC TC7SHU04FU (T5RSOJF) R742 1-216-833-11 METAL CHIP 10K 5% 1/10W
R743 1-216-809-11 METAL CHIP 100 5% 1/10W
< COIL/JUMPER RESISTOR >
R744 1-216-864-11 SHORT CHIP 0
L701 1-216-295-00 SHORT CHIP 0 R745 1-216-809-11 METAL CHIP 100 5% 1/10W
L702 1-469-967-21 INDUCTOR 10uH R746 1-216-809-11 METAL CHIP 100 5% 1/10W
L703 1-469-967-21 INDUCTOR 10uH R747 1-216-809-11 METAL CHIP 100 5% 1/10W
L704 1-469-967-21 INDUCTOR 10uH R748 1-216-841-11 METAL CHIP 47K 5% 1/10W
L705 1-412-939-11 INDUCTOR 1uH

71
HCD-CPZ1DAB
AMP CD

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R749 1-216-864-11 SHORT CHIP 0
R750 1-216-841-11 METAL CHIP 47K 5% 1/10W C112 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
R751 1-216-864-11 SHORT CHIP 0 C113 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
R752 1-216-837-11 METAL CHIP 22K 5% 1/10W C201 1-128-995-21 ELECT CHIP 100uF 20% 10V
R754 1-216-817-11 METAL CHIP 470 5% 1/10W C202 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C203 1-128-995-21 ELECT CHIP 100uF 20% 10V
R756 1-216-809-11 METAL CHIP 100 5% 1/10W
R757 1-216-864-11 SHORT CHIP 0 C204 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R758 1-216-864-11 SHORT CHIP 0 C205 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R759 1-216-864-11 SHORT CHIP 0 C206 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R761 1-216-809-11 METAL CHIP 100 5% 1/10W C207 1-128-995-21 ELECT CHIP 100uF 20% 10V
C208 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R762 1-216-809-11 METAL CHIP 100 5% 1/10W
R764 1-216-864-11 SHORT CHIP 0 C210 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R765 1-216-864-11 SHORT CHIP 0 C213 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R768 1-216-833-11 METAL CHIP 10K 5% 1/10W C214 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R769 1-220-942-11 METAL CHIP 3.3 1% 1/4W C215 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C217 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R770 1-220-942-11 METAL CHIP 3.3 1% 1/4W
R771 1-216-833-11 METAL CHIP 10K 5% 1/10W C218 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R772 1-216-833-11 METAL CHIP 10K 5% 1/10W C219 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R773 1-216-833-11 METAL CHIP 10K 5% 1/10W C220 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R774 1-216-793-11 METAL CHIP 4.7 5% 1/10W C221 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C222 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R775 1-216-793-11 METAL CHIP 4.7 5% 1/10W
R776 1-216-849-11 METAL CHIP 220K 5% 1/10W C223 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R777 1-216-845-11 METAL CHIP 100K 5% 1/10W C224 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R778 1-216-849-11 METAL CHIP 220K 5% 1/10W C226 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R779 1-216-864-11 SHORT CHIP 0 C227 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C230 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
R781 1-216-809-11 METAL CHIP 100 5% 1/10W
R782 1-216-857-11 METAL CHIP 1M 5% 1/10W C232 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R783 1-216-809-11 METAL CHIP 100 5% 1/10W C251 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
R784 1-216-809-11 METAL CHIP 100 5% 1/10W C252 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
R785 1-216-809-11 METAL CHIP 100 5% 1/10W C253 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C254 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
R786 1-216-809-11 METAL CHIP 100 5% 1/10W
R787 1-216-809-11 METAL CHIP 100 5% 1/10W C256 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R788 1-216-809-11 METAL CHIP 100 5% 1/10W C257 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R789 1-216-809-11 METAL CHIP 100 5% 1/10W C258 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
R790 1-216-809-11 METAL CHIP 100 5% 1/10W C260 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C261 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R792 1-216-864-11 SHORT CHIP 0
R793 1-216-841-11 METAL CHIP 47K 5% 1/10W C264 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R800 1-216-821-11 METAL CHIP 1K 5% 1/10W C265 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R801 1-216-821-11 METAL CHIP 1K 5% 1/10W C266 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C267 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
< VIBRATOR > C268 1-162-919-11 CERAMIC CHIP 22PF 5% 50V

X701 1-795-843-11 VIBRATOR, CRYSTAL (12.288MHz) C269 1-126-208-21 ELECT CHIP 47uF 20% 4V
X702 1-795-660-21 QUARTZ CRYSTAL UNIT (49.152MHz) C270 1-126-208-21 ELECT CHIP 47uF 20% 4V
************************************************************ C271 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C272 1-164-360-11 CERAMIC CHIP 0.1uF 16V
A-1134-281-A CD BOARD, COMPLETE C273 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
*******************
C274 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< CAPACITOR > C275 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C291 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C101 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C292 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C102 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C301 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C103 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C104 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C303 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3V
C105 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C304 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C321 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C107 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C322 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C108 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C323 1-128-995-21 ELECT CHIP 100uF 20% 10V
C109 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C110 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C401 1-128-394-11 ELECT CHIP 220uF 20% 10V
C111 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C404 1-164-360-11 CERAMIC CHIP 0.1uF 16V

72
 HCD-CPZ1DAB
CD DAB

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C405 1-164-360-11 CERAMIC CHIP 0.1uF 16V R292 1-216-809-11 METAL CHIP 100 5% 1/10W
C406 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C424 1-164-360-11 CERAMIC CHIP 0.1uF 16V R321 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R322 1-216-789-11 METAL CHIP 2.2 5% 1/10W
C451 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V R323 1-216-864-11 SHORT CHIP 0
R324 1-216-845-11 METAL CHIP 100K 5% 1/10W
< CONNECTOR > R401 1-216-295-00 SHORT CHIP 0

CN102 1-770-706-21 CONNECTOR, FFC/FPC 23P R421 1-216-864-11 SHORT CHIP 0

CN301 1-770-425-51 CONNECTOR, FFC/FPC 16P R423 1-216-833-11 METAL CHIP 10K 5% 1/10W
R451 1-216-837-11 METAL CHIP 22K 5% 1/10W
< IC > R452 1-216-833-11 METAL CHIP 10K 5% 1/10W

IC201 8-753-246-30 IC CXD3014A-201R < VIBRATOR >

IC203 6-709-704-01 IC TK63118SCL-G
IC402 6-705-808-01 IC BA5947FM-E2 X202 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
************************************************************
< TRANSISTOR >
A-1193-284-A DAB BOARD, COMPLETE
Q321 6-551-120-01 TRANSISTOR 2SA2119K ********************

< RESISTOR/FERRITE BEAD > < CAPACITOR/JUMPER RESISTOR >

R101 1-216-809-11 METAL CHIP 100 5% 1/10W C801 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R102 1-216-809-11 METAL CHIP 100 5% 1/10W C803 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
R103 1-216-809-11 METAL CHIP 100 5% 1/10W C804 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R104 1-216-809-11 METAL CHIP 100 5% 1/10W C805 1-126-933-11 ELECT 100uF 20% 16V
R105 1-216-809-11 METAL CHIP 100 5% 1/10W C811 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

R107 1-216-809-11 METAL CHIP 100 5% 1/10W C812 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R108 1-216-809-11 METAL CHIP 100 5% 1/10W C813 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
R109 1-216-809-11 METAL CHIP 100 5% 1/10W C814 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
R110 1-216-809-11 METAL CHIP 100 5% 1/10W C815 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R111 1-216-809-11 METAL CHIP 100 5% 1/10W C816 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

R112 1-216-809-11 METAL CHIP 100 5% 1/10W C817 1-126-960-11 ELECT 1uF 20% 50V
R113 1-216-809-11 METAL CHIP 100 5% 1/10W C818 1-126-960-11 ELECT 1uF 20% 50V
R201 1-216-295-00 SHORT CHIP 0 C820 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R202 1-216-295-00 SHORT CHIP 0 C821 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R203 1-500-445-21 FERRITE, EMI (SMD) (2012) C822 1-126-923-11 ELECT 220uF 20% 10V

R207 1-216-295-00 SHORT CHIP 0 C823 1-126-918-11 ELECT 4700uF 20% 6.3V
R250 1-216-857-11 METAL CHIP 1M 5% 1/10W C825 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R252 1-216-833-11 METAL CHIP 10K 5% 1/10W C828 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R253 1-216-821-11 METAL CHIP 1K 5% 1/10W C829 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R254 1-216-833-11 METAL CHIP 10K 5% 1/10W C832 1-216-864-11 SHORT CHIP 0

R255 1-216-821-11 METAL CHIP 1K 5% 1/10W < CONNECTOR >

R256 1-216-837-11 METAL CHIP 22K 5% 1/10W
R257 1-216-845-11 METAL CHIP 100K 5% 1/10W CN800 1-818-488-11 PIN, CONNECTOR (PC BOARD) 44P
R258 1-216-849-11 METAL CHIP 220K 5% 1/10W CNS801 1-784-731-11 CONNECTOR, FFC 9P
R260 1-216-864-11 SHORT CHIP 0
< DIODE >
R265 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R266 1-216-821-11 METAL CHIP 1K 5% 1/10W D801 8-719-913-42 DIODE 1N4002T
R267 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R268 1-216-833-11 METAL CHIP 10K 5% 1/10W < GROUND TERMINAL >
R269 1-216-809-11 METAL CHIP 100 5% 1/10W
EP801 1-537-771-21 TERMINAL BOARD, GROUND
R270 1-216-817-11 METAL CHIP 470 5% 1/10W
R271 1-216-857-11 METAL CHIP 1M 5% 1/10W < FERRITE BEAD >
R272 1-500-445-21 FERRITE, EMI (SMD) (2012)
R275 1-216-809-11 METAL CHIP 100 5% 1/10W FB801 1-410-397-21 FERRITE 1.1uH
R276 1-216-841-11 METAL CHIP 47K 5% 1/10W
< IC >
R277 1-216-809-11 METAL CHIP 100 5% 1/10W
R278 1-216-809-11 METAL CHIP 100 5% 1/10W IC801 6-710-300-01 IC BD33KA5WFP-E2
R280 1-216-864-11 SHORT CHIP 0 IC803 6-702-945-01 IC NJM14558V-TE2
R291 1-216-809-11 METAL CHIP 100 5% 1/10W IC805 6-706-468-01 IC BA50BC0WFP-E2

73
HCD-CPZ1DAB
DAB DRIVER HP/MD LCD

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

< FERRITE BEAD > HP/MD BOARD

************
L803 1-469-152-11 FERRITE, EMI (SMD) (2012)
L804 1-469-152-11 FERRITE, EMI (SMD) (2012) < CAPACITOR >

< RESISTOR > C983 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C984 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R800 1-216-821-11 METAL CHIP 1K 5% 1/10W C985 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R801 1-216-833-11 METAL CHIP 10K 5% 1/10W C986 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R802 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C990 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
R803 1-216-821-11 METAL CHIP 1K 5% 1/10W
R804 1-216-821-11 METAL CHIP 1K 5% 1/10W C991 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C992 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
R805 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R806 1-216-829-11 METAL CHIP 4.7K 5% 1/10W < EARTH TERMINAL >
R807 1-216-833-11 METAL CHIP 10K 5% 1/10W
R808 1-216-833-11 METAL CHIP 10K 5% 1/10W EP981 1-537-771-21 TERMINAL BOARD, GROUND
R809 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
< JUMPER RESISTOR >
R810 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R811 1-216-829-11 METAL CHIP 4.7K 5% 1/10W FB981 1-216-864-11 SHORT CHIP 0
R812 1-216-829-11 METAL CHIP 4.7K 5% 1/10W FB982 1-216-864-11 SHORT CHIP 0
R813 1-216-833-11 METAL CHIP 10K 5% 1/10W FB983 1-216-864-11 SHORT CHIP 0
R814 1-216-833-11 METAL CHIP 10K 5% 1/10W
< JACK >
R823 1-216-845-11 METAL CHIP 100K 5% 1/10W
R824 1-216-845-11 METAL CHIP 100K 5% 1/10W J981 1-815-603-11 JACK (ANALOG IN)
R825 1-216-829-11 METAL CHIP 4.7K 5% 1/10W J982 1-815-603-11 JACK (PHONES)
R826 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R827 1-216-845-11 METAL CHIP 100K 5% 1/10W < RESISTOR >

R829 1-216-864-11 SHORT CHIP 0 R982 1-216-821-11 METAL CHIP 1K 5% 1/10W

R830 1-216-809-11 METAL CHIP 100 5% 1/10W R983 1-216-845-11 METAL CHIP 100K 5% 1/10W
R831 1-216-864-11 SHORT CHIP 0 R984 1-216-821-11 METAL CHIP 1K 5% 1/10W
R832 1-216-809-11 METAL CHIP 100 5% 1/10W R985 1-216-845-11 METAL CHIP 100K 5% 1/10W
R838 1-216-864-11 SHORT CHIP 0 ************************************************************
************************************************************
LCD BOARD
1-688-337-11 DRIVER BOARD **********
*************
2-687-696-01 HOLDER (LCD)
< CAPACITOR >
< CAPACITOR >
C705 1-162-300-21 CERAMIC 0.01uF 30% 16V
C711 1-126-964-11 ELECT 10uF 20% 50V C951 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C952 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR > C953 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C954 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
CN701 1-785-333-11 PIN, CONNECTOR (LIGHT ANGLE) 7P C955 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

< DIODE > C956 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C957 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
D701 8-719-923-31 DIODE MTZJ-T-77-4.7C C965 1-164-156-11 CERAMIC CHIP 0.1uF 25V

< IC > < CONNECTOR >

IC701 8-759-598-69 IC BA6956AN CN951 1-784-729-11 CONNECTOR, FFC 7P

< RESISTOR > < LED >

R701 1-247-827-91 CARBON 680 5% 1/4W D951 6-501-138-01 LED SELU2WA10C-LF62 (LCD BACK LIGHT)
R702 1-247-807-31 CARBON 100 5% 1/4W D952 6-501-138-01 LED SELU2WA10C-LF62 (LCD BACK LIGHT)

< SWITCH > < LIQUID CRYSTAL DISPLAY >

S701 1-762-951-21 SWITCH, PUSH (OUT) LCD951 1-802-192-11 DISPLAY PANEL, LIQUID CRYSTAL
S702 1-762-951-21 SWITCH, PUSH (CHUCK)
************************************************************

74
 HCD-CPZ1DAB
LCD MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR > C508 1-130-475-00 MYLAR 0.0022uF 5% 50V
C509 1-126-960-11 ELECT 1uF 20% 50V
R954 1-216-809-11 METAL CHIP 100 5% 1/10W
R955 1-216-809-11 METAL CHIP 100 5% 1/10W C510 1-126-960-11 ELECT 1uF 20% 50V
R956 1-216-809-11 METAL CHIP 100 5% 1/10W C511 1-126-964-11 ELECT 10uF 20% 50V
R957 1-216-809-11 METAL CHIP 100 5% 1/10W C512 1-126-960-11 ELECT 1uF 20% 50V
R959 1-216-805-11 METAL CHIP 47 5% 1/10W C514 1-126-960-11 ELECT 1uF 20% 50V
C515 1-126-964-11 ELECT 10uF 20% 50V
R961 1-216-805-11 METAL CHIP 47 5% 1/10W
************************************************************ C517 1-126-934-11 ELECT 220uF 20% 16V
C518 1-126-933-11 ELECT 100uF 20% 16V
A-1193-279-A MAIN BOARD, COMPLETE C519 1-164-156-11 CERAMIC CHIP 0.1uF 25V
********************* C524 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C527 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
C550 1-126-965-11 ELECT 22uF 20% 50V
< CAPACITOR > C552 1-126-964-11 ELECT 10uF 20% 50V
C554 1-126-960-11 ELECT 1uF 20% 50V
C200 1-126-960-11 ELECT 1uF 20% 50V C555 1-126-964-11 ELECT 10uF 20% 50V
C201 1-126-937-11 ELECT 4700uF 20% 16V C556 1-136-497-81 FILM 0.1uF 5% 50V
C202 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C204 1-164-156-11 CERAMIC CHIP 0.1uF 25V C557 1-136-497-81 FILM 0.1uF 5% 50V
C206 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C558 1-130-475-00 MYLAR 0.0022uF 5% 50V
C559 1-126-960-11 ELECT 1uF 20% 50V
C207 1-126-925-11 ELECT 470uF 20% 10V C560 1-126-960-11 ELECT 1uF 20% 50V
C208 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C561 1-126-964-11 ELECT 10uF 20% 50V
C209 1-126-925-11 ELECT 470uF 20% 10V
C210 1-164-156-11 CERAMIC CHIP 0.1uF 25V C562 1-126-960-11 ELECT 1uF 20% 50V
C211 1-164-156-11 CERAMIC CHIP 0.1uF 25V C564 1-126-960-11 ELECT 1uF 20% 50V
C565 1-126-964-11 ELECT 10uF 20% 50V
C212 1-164-156-11 CERAMIC CHIP 0.1uF 25V C567 1-126-923-11 ELECT 220uF 20% 10V
C214 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C574 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C215 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C216 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < CONNECTOR >
C217 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
CN201 1-564-505-11 PLUG, CONNECTOR 2P
C218 1-165-908-11 CERAMIC CHIP 1uF 10% 10V CN202 1-815-443-11 PIN, CONNECTOR (PWB) 2P
C301 1-126-916-11 ELECT 1000uF 20% 6.3V CN300 1-815-444-11 PIN, CONNECTOR (PWB) 3P
C309 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V CN301 1-784-780-11 CONNECTOR, FFC 19P
C310 1-162-919-11 CERAMIC CHIP 22PF 5% 50V CN302 1-784-782-11 CONNECTOR, FFC 21P
C311 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
* CN303 1-815-448-11 PIN, CONNECTOR (PWB) 7P
C312 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN304 1-784-768-11 CONNECTOR, FFC 7P
C316 1-164-156-11 CERAMIC CHIP 0.1uF 25V CN305 1-784-780-11 CONNECTOR, FFC 19P
C321 1-126-960-11 ELECT 1uF 20% 50V * CN306 1-815-448-11 PIN, CONNECTOR (PWB) 7P
C322 1-126-960-11 ELECT 1uF 20% 50V CN307 1-815-444-11 PIN, CONNECTOR (PWB) 3P
C351 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
CN308 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
C359 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V CN309 1-784-776-11 CONNECTOR, FFC 15P
C362 1-164-156-11 CERAMIC CHIP 0.1uF 25V CN310 1-784-770-11 CONNECTOR, FFC 9P
C401 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C402 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < DIODE >
C403 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
D202 8-719-913-42 DIODE 1N4002T
C404 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D203 8-719-913-42 DIODE 1N4002T
C405 1-164-156-11 CERAMIC CHIP 0.1uF 25V D204 8-719-913-42 DIODE 1N4002T
C407 1-164-156-11 CERAMIC CHIP 0.1uF 25V D205 8-719-913-42 DIODE 1N4002T
C421 1-126-960-11 ELECT 1uF 20% 50V D301 6-500-334-01 DIODE MC2836-T112-1
C422 1-126-960-11 ELECT 1uF 20% 50V
D302 6-500-334-01 DIODE MC2836-T112-1
C431 1-164-156-11 CERAMIC CHIP 0.1uF 25V D303 6-500-334-01 DIODE MC2836-T112-1
C432 1-164-156-11 CERAMIC CHIP 0.1uF 25V D305 6-501-193-01 DIODE 1SS355WTE-17
C501 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D306 6-501-193-01 DIODE 1SS355WTE-17
C503 1-126-934-11 ELECT 220uF 20% 16V D307 6-501-193-01 DIODE 1SS355WTE-17
C504 1-126-960-11 ELECT 1uF 20% 50V
D308 8-719-913-42 DIODE 1N4002T
C505 1-126-964-11 ELECT 10uF 20% 50V D405 8-719-913-42 DIODE 1N4002T
C506 1-136-497-81 FILM 0.1uF 5% 50V D406 8-719-913-42 DIODE 1N4002T
C507 1-136-497-81 FILM 0.1uF 5% 50V D410 8-719-913-42 DIODE 1N4002T

75
HCD-CPZ1DAB
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R318 1-216-809-11 METAL CHIP 100 5% 1/10W
< EARTH TERMINAL > R319 1-216-809-11 METAL CHIP 100 5% 1/10W
R320 1-216-841-11 METAL CHIP 47K 5% 1/10W
EP301 1-537-771-21 TERMINAL BOARD, GROUND R321 1-216-809-11 METAL CHIP 100 5% 1/10W
EP302 1-537-771-21 TERMINAL BOARD, GROUND R322 1-216-809-11 METAL CHIP 100 5% 1/10W

< FERRITE BEAD > R323 1-216-809-11 METAL CHIP 100 5% 1/10W
R324 1-216-809-11 METAL CHIP 100 5% 1/10W
FB200 1-410-397-21 FERRITE 1.1uH R325 1-216-809-11 METAL CHIP 100 5% 1/10W
R326 1-216-809-11 METAL CHIP 100 5% 1/10W
< IC > R327 1-216-809-11 METAL CHIP 100 5% 1/10W

IC200 6-709-978-01 IC BAJ2DD0T R328 1-216-809-11 METAL CHIP 100 5% 1/10W

IC201 8-759-071-48 IC TA7807S R329 1-216-809-11 METAL CHIP 100 5% 1/10W
IC202 6-703-546-01 IC TA7804LS R330 1-216-809-11 METAL CHIP 100 5% 1/10W
IC203 8-759-231-56 IC TA7809S R331 1-216-809-11 METAL CHIP 100 5% 1/10W
IC204 6-707-282-01 IC MM1615ANLE R332 1-216-809-11 METAL CHIP 100 5% 1/10W

IC301 6-806-756-01 IC M30624MGP-A59FPU0 R333 1-216-809-11 METAL CHIP 100 5% 1/10W

IC302 6-701-680-01 IC PST3629NR R334 1-216-809-11 METAL CHIP 100 5% 1/10W
IC421 8-759-367-79 IC MC14052BFEL R335 1-216-809-11 METAL CHIP 100 5% 1/10W
IC501 6-707-974-01 IC BD3872FS R336 1-216-809-11 METAL CHIP 100 5% 1/10W
IC502 8-759-656-83 IC NJM4580MD- (TE2) R337 1-216-809-11 METAL CHIP 100 5% 1/10W

< JUMPER RESISTOR > R338 1-216-809-11 METAL CHIP 100 5% 1/10W
R339 1-216-809-11 METAL CHIP 100 5% 1/10W
JR401 1-216-864-11 SHORT CHIP 0 R340 1-216-809-11 METAL CHIP 100 5% 1/10W
R341 1-216-809-11 METAL CHIP 100 5% 1/10W
< JUMPER RESISTOR > R342 1-216-809-11 METAL CHIP 100 5% 1/10W

L201 1-216-864-11 SHORT CHIP 0 R343 1-216-809-11 METAL CHIP 100 5% 1/10W
L411 1-216-864-11 SHORT CHIP 0 R344 1-216-809-11 METAL CHIP 100 5% 1/10W
L491 1-216-864-11 SHORT CHIP 0 R345 1-216-809-11 METAL CHIP 100 5% 1/10W
L492 1-216-864-11 SHORT CHIP 0 R346 1-216-809-11 METAL CHIP 100 5% 1/10W
L493 1-216-864-11 SHORT CHIP 0 R347 1-216-809-11 METAL CHIP 100 5% 1/10W

< TRANSISTOR > R348 1-216-809-11 METAL CHIP 100 5% 1/10W

R349 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q301 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF R354 1-216-809-11 METAL CHIP 100 5% 1/10W
Q401 8-729-038-23 TRANSISTOR RT1N141C-TP-1 R355 1-216-809-11 METAL CHIP 100 5% 1/10W
Q402 8-729-038-12 TRANSISTOR RT1P141C-TP-1 R356 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q403 8-729-038-23 TRANSISTOR RT1N141C-TP-1
Q404 8-729-038-12 TRANSISTOR RT1P141C-TP-1 R357 1-216-809-11 METAL CHIP 100 5% 1/10W
R360 1-216-809-11 METAL CHIP 100 5% 1/10W
Q411 8-729-038-23 TRANSISTOR RT1N141C-TP-1 R361 1-216-809-11 METAL CHIP 100 5% 1/10W
Q412 8-729-620-33 TRANSISTOR 2SA1235TP-1EF R362 1-216-809-11 METAL CHIP 100 5% 1/10W
Q413 6-550-889-01 TRANSISTOR 2SC5938-T112-1B R365 1-216-809-11 METAL CHIP 100 5% 1/10W
Q414 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
Q421 8-729-038-28 TRANSISTOR RT1N441C-TP-1 R366 1-216-809-11 METAL CHIP 100 5% 1/10W
R367 1-216-809-11 METAL CHIP 100 5% 1/10W
Q422 8-729-038-28 TRANSISTOR RT1N441C-TP-1 R368 1-216-809-11 METAL CHIP 100 5% 1/10W
Q463 6-550-889-01 TRANSISTOR 2SC5938-T112-1B R369 1-216-809-11 METAL CHIP 100 5% 1/10W
Q464 6-550-889-01 TRANSISTOR 2SC5938-T112-1B R370 1-216-809-11 METAL CHIP 100 5% 1/10W
Q551 8-729-036-95 TRANSISTOR KTC3198GR-A
R371 1-216-809-11 METAL CHIP 100 5% 1/10W
< RESISTOR > R372 1-216-809-11 METAL CHIP 100 5% 1/10W
R373 1-216-809-11 METAL CHIP 100 5% 1/10W
R301 1-216-833-11 METAL CHIP 10K 5% 1/10W R374 1-216-809-11 METAL CHIP 100 5% 1/10W
R302 1-216-809-11 METAL CHIP 100 5% 1/10W R376 1-216-809-11 METAL CHIP 100 5% 1/10W
R303 1-216-809-11 METAL CHIP 100 5% 1/10W
R304 1-216-809-11 METAL CHIP 100 5% 1/10W R377 1-216-809-11 METAL CHIP 100 5% 1/10W
R305 1-216-809-11 METAL CHIP 100 5% 1/10W R378 1-216-809-11 METAL CHIP 100 5% 1/10W
R379 1-216-809-11 METAL CHIP 100 5% 1/10W
R306 1-216-809-11 METAL CHIP 100 5% 1/10W R380 1-216-809-11 METAL CHIP 100 5% 1/10W
R307 1-216-809-11 METAL CHIP 100 5% 1/10W R382 1-216-809-11 METAL CHIP 100 5% 1/10W
R309 1-216-833-11 METAL CHIP 10K 5% 1/10W
R311 1-216-845-11 METAL CHIP 100K 5% 1/10W R383 1-216-809-11 METAL CHIP 100 5% 1/10W
R313 1-216-864-11 SHORT CHIP 0 R384 1-216-809-11 METAL CHIP 100 5% 1/10W
R385 1-216-809-11 METAL CHIP 100 5% 1/10W

76
 HCD-CPZ1DAB
MAIN OPT PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R386 1-216-809-11 METAL CHIP 100 5% 1/10W R495 1-216-833-11 METAL CHIP 10K 5% 1/10W
R387 1-216-809-11 METAL CHIP 100 5% 1/10W R497 1-216-833-11 METAL CHIP 10K 5% 1/10W
R501 1-216-821-11 METAL CHIP 1K 5% 1/10W
R388 1-216-809-11 METAL CHIP 100 5% 1/10W R502 1-216-833-11 METAL CHIP 10K 5% 1/10W
R389 1-216-809-11 METAL CHIP 100 5% 1/10W R503 1-216-821-11 METAL CHIP 1K 5% 1/10W
R390 1-216-809-11 METAL CHIP 100 5% 1/10W
R391 1-216-809-11 METAL CHIP 100 5% 1/10W R504 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R392 1-216-809-11 METAL CHIP 100 5% 1/10W R505 1-216-837-11 METAL CHIP 22K 5% 1/10W
R506 1-216-849-11 METAL CHIP 220K 5% 1/10W
R394 1-216-809-11 METAL CHIP 100 5% 1/10W R507 1-216-805-11 METAL CHIP 47 5% 1/10W
R395 1-216-809-11 METAL CHIP 100 5% 1/10W R509 1-216-833-11 METAL CHIP 10K 5% 1/10W
R397 1-216-809-11 METAL CHIP 100 5% 1/10W
R400 1-216-809-11 METAL CHIP 100 5% 1/10W R510 1-216-845-11 METAL CHIP 100K 5% 1/10W
R401 1-216-841-11 METAL CHIP 47K 5% 1/10W R511 1-216-821-11 METAL CHIP 1K 5% 1/10W
R512 1-216-833-11 METAL CHIP 10K 5% 1/10W
R402 1-216-841-11 METAL CHIP 47K 5% 1/10W R516 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R403 1-216-833-11 METAL CHIP 10K 5% 1/10W R522 1-216-821-11 METAL CHIP 1K 5% 1/10W
R404 1-216-845-11 METAL CHIP 100K 5% 1/10W
R405 1-216-837-11 METAL CHIP 22K 5% 1/10W R523 1-216-821-11 METAL CHIP 1K 5% 1/10W
R406 1-216-821-11 METAL CHIP 1K 5% 1/10W R547 1-216-813-11 METAL CHIP 220 5% 1/10W
R550 1-216-837-11 METAL CHIP 22K 5% 1/10W
R410 1-216-833-11 METAL CHIP 10K 5% 1/10W R551 1-216-821-11 METAL CHIP 1K 5% 1/10W
R411 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R552 1-216-833-11 METAL CHIP 10K 5% 1/10W
R412 1-216-833-11 METAL CHIP 10K 5% 1/10W
R413 1-216-801-11 METAL CHIP 22 5% 1/10W R553 1-216-821-11 METAL CHIP 1K 5% 1/10W
R414 1-216-809-11 METAL CHIP 100 5% 1/10W R554 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R555 1-216-837-11 METAL CHIP 22K 5% 1/10W
R415 1-216-801-11 METAL CHIP 22 5% 1/10W R556 1-216-849-11 METAL CHIP 220K 5% 1/10W
R417 1-216-833-11 METAL CHIP 10K 5% 1/10W R557 1-216-805-11 METAL CHIP 47 5% 1/10W
R420 1-216-833-11 METAL CHIP 10K 5% 1/10W
R421 1-216-845-11 METAL CHIP 100K 5% 1/10W R558 1-216-837-11 METAL CHIP 22K 5% 1/10W
R422 1-216-845-11 METAL CHIP 100K 5% 1/10W R559 1-216-837-11 METAL CHIP 22K 5% 1/10W
R560 1-216-845-11 METAL CHIP 100K 5% 1/10W
R425 1-216-833-11 METAL CHIP 10K 5% 1/10W R561 1-216-821-11 METAL CHIP 1K 5% 1/10W
R427 1-216-833-11 METAL CHIP 10K 5% 1/10W R562 1-216-833-11 METAL CHIP 10K 5% 1/10W
R428 1-216-833-11 METAL CHIP 10K 5% 1/10W
R429 1-216-833-11 METAL CHIP 10K 5% 1/10W R563 1-216-809-11 METAL CHIP 100 5% 1/10W
R430 1-216-833-11 METAL CHIP 10K 5% 1/10W R566 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R431 1-216-845-11 METAL CHIP 100K 5% 1/10W < VIBRATOR >

R432 1-216-845-11 METAL CHIP 100K 5% 1/10W
R433 1-216-845-11 METAL CHIP 100K 5% 1/10W X301 1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
R434 1-216-845-11 METAL CHIP 100K 5% 1/10W X302 1-795-482-11 VIBRATOR, CERAMIC (16MHz)
R435 1-216-817-11 METAL CHIP 470 5% 1/10W ************************************************************

R436 1-216-809-11 METAL CHIP 100 5% 1/10W OPT BOARD

R437 1-216-845-11 METAL CHIP 100K 5% 1/10W **********
R438 1-216-845-11 METAL CHIP 100K 5% 1/10W
R439 1-216-833-11 METAL CHIP 10K 5% 1/10W < CAPACITOR >
R440 1-216-821-11 METAL CHIP 1K 5% 1/10W
C982 1-115-156-11 CERAMIC CHIP 1uF 10V
R453 1-216-833-11 METAL CHIP 10K 5% 1/10W
R454 1-216-833-11 METAL CHIP 10K 5% 1/10W < IC >
R455 1-216-845-11 METAL CHIP 100K 5% 1/10W
R456 1-216-821-11 METAL CHIP 1K 5% 1/10W IC981 6-600-012-01 IC TOTX141L (CD DIGITAL OUT)
R457 1-216-833-11 METAL CHIP 10K 5% 1/10W
< RESISTOR >
R468 1-216-833-11 METAL CHIP 10K 5% 1/10W
R469 1-216-833-11 METAL CHIP 10K 5% 1/10W R981 1-216-821-11 METAL CHIP 1K 5% 1/10W
R470 1-216-833-11 METAL CHIP 10K 5% 1/10W ************************************************************
R471 1-216-833-11 METAL CHIP 10K 5% 1/10W
R474 1-216-857-11 METAL CHIP 1M 5% 1/10W PANEL BOARD
************
R476 1-216-833-11 METAL CHIP 10K 5% 1/10W
R477 1-216-833-11 METAL CHIP 10K 5% 1/10W < CAPACITOR >
R490 1-216-821-11 METAL CHIP 1K 5% 1/10W
R493 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C905 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R494 1-216-833-11 METAL CHIP 10K 5% 1/10W C906 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C907 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

77
HCD-CPZ1DAB
PANEL SP SUB PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C908 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R939 1-216-833-11 METAL CHIP 10K 5% 1/10W
C909 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< ROTARY ENCODER >
C910 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C911 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V RV901 1-418-859-31 ENCODER, ROTARY (BASS)
C912 1-164-156-11 CERAMIC CHIP 0.1uF 25V RV902 1-418-859-31 ENCODER, ROTARY (TREBLE)
C913 1-164-156-11 CERAMIC CHIP 0.1uF 25V RV903 1-479-195-11 ENCODER (VOLUME)
RV904 1-478-061-11 ENCODER, ROTARY (PUSH ENTER (JOG))
< CONNECTOR >
< SWITCH >
CN901 1-784-741-11 CONNECTOR, FFC 19P
* CN902 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P S901 1-762-875-21 SWITCH, KEYBOARD (I/1)
S902 1-762-875-21 SWITCH, KEYBOARD (DSGX)
< LED > S903 1-762-875-21 SWITCH, KEYBOARD
(PLAY MODE, DIRECTION, TUNING MODE)
D901 8-719-032-83 LED SEL5220S-TP15 (STANDBY) S904 1-762-875-21 SWITCH, KEYBOARD (DAB AUTO SCAN)
D902 6-501-539-01 LED SELK5E20C-DTP15 (TUNER/BAND) S905 1-762-875-21 SWITCH, KEYBOARD (CD SYNCHRO)
D903 6-501-539-01 LED SELK5E20C-DTP15 (TAPE Y)
S906 1-762-875-21 SWITCH, KEYBOARD (FUNCTION)
< IC > S907 1-762-875-21 SWITCH, KEYBOARD (z REC)
S908 1-762-875-21 SWITCH, KEYBOARD (X (TAPE))
IC901 6-600-349-31 IC NJL24H400A S909 1-762-875-21 SWITCH, KEYBOARD (x (TAPE))
S910 1-762-875-21 SWITCH, KEYBOARD (TAPE Y)
< TRANSISTOR >
S914 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)
Q901 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF S915 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)
Q902 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF S916 1-762-875-21 SWITCH, KEYBOARD (TUNING +)
Q903 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF S917 1-762-875-21 SWITCH, KEYBOARD (TUNING –)
Q904 8-729-620-33 TRANSISTOR 2SA1235TP-1EF S918 1-762-875-21 SWITCH, KEYBOARD (GROUP +)
Q905 8-729-038-23 TRANSISTOR RT1N141C-TP-1
S919 1-762-875-21 SWITCH, KEYBOARD (GROUP –)
< RESISTOR > ************************************************************

R901 1-216-821-11 METAL CHIP 1K 5% 1/10W SP BOARD

R902 1-216-825-11 METAL CHIP 2.2K 5% 1/10W *********
R903 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R904 1-216-829-11 METAL CHIP 4.7K 5% 1/10W < CAPACITOR >
R905 1-216-833-11 METAL CHIP 10K 5% 1/10W
C851 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R906 1-216-821-11 METAL CHIP 1K 5% 1/10W C852 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R907 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C853 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R908 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C854 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R911 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R912 1-216-821-11 METAL CHIP 1K 5% 1/10W < CONNECTOR >

R913 1-216-825-11 METAL CHIP 2.2K 5% 1/10W CN850 1-564-505-11 PLUG, CONNECTOR 2P
R914 1-216-829-11 METAL CHIP 4.7K 5% 1/10W CN870 1-564-505-11 PLUG, CONNECTOR 2P
R915 1-216-833-11 METAL CHIP 10K 5% 1/10W
R916 1-216-837-11 METAL CHIP 22K 5% 1/10W < TERMINAL BOARD >
R917 1-216-841-11 METAL CHIP 47K 5% 1/10W
J860 1-537-114-21 TERMINAL BOARD (SPEAKER)
R920 1-216-813-11 METAL CHIP 220 5% 1/10W ************************************************************
R921 1-216-817-11 METAL CHIP 470 5% 1/10W
R922 1-216-813-11 METAL CHIP 220 5% 1/10W SUB PANEL BOARD
R923 1-216-817-11 METAL CHIP 470 5% 1/10W ****************
R924 1-216-833-11 METAL CHIP 10K 5% 1/10W
< CAPACITOR >
R926 1-216-833-11 METAL CHIP 10K 5% 1/10W
R928 1-216-833-11 METAL CHIP 10K 5% 1/10W C914 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R930 1-216-833-11 METAL CHIP 10K 5% 1/10W
R932 1-216-825-11 METAL CHIP 2.2K 5% 1/10W < LED >
R933 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D904 6-501-539-01 LED SELK5E20C-DTP15 (CD u)
R934 1-216-821-11 METAL CHIP 1K 5% 1/10W
R935 1-216-833-11 METAL CHIP 10K 5% 1/10W < RESISTOR >
R936 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R937 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R909 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R938 1-216-821-11 METAL CHIP 1K 5% 1/10W R910 1-216-833-11 METAL CHIP 10K 5% 1/10W

78
 HCD-CPZ1DAB
SUB PANEL SUB POWER SW POWER

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< SWITCH > 0 C16 1-126-963-11 ELECT 4.7uF 20% 50V
0 C17 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
S911 1-762-875-21 SWITCH, KEYBOARD (x/CANCEL (CD))
S912 1-762-875-21 SWITCH, KEYBOARD (CD u) 0 C18 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
S913 1-762-875-21 SWITCH, KEYBOARD (Z (CD)) 0 C19 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
************************************************************ 0 C20 1-104-664-11 ELECT 47uF 20% 25V
0 C21 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
SUB POWER BOARD 0 C22 1-107-824-11 CERAMIC 220PF 5% 1KV
*****************
0 C23 1-107-824-11 CERAMIC 220PF 5% 1KV
< CAPACITOR > 0 C24 1-128-990-22 FILM 27000PF 3% 800V
0 C25 1-126-948-11 ELECT 100uF 20% 35V
0 C991 1-113-925-11 CERAMIC 0.01uF 20% 250V 0 C26 1-112-877-51 CERAMIC 0.001uF 20% 125V
0 C992 1-113-925-11 CERAMIC 0.01uF 20% 250V C31 1-128-953-31 ELECT 470uF 20% 25V
C993 1-126-768-11 ELECT 2200uF 20% 16V
C994 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C32 1-100-924-21 ELECT 2200uF 20% 35V
C995 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C51 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C52 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR > C53 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

CN990 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P < CONNECTOR >

< DIODE > CN1 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P

* CN31 1-564-508-11 PLUG, CONNECTOR 5P
D991 6-501-193-01 DIODE 1SS355WTE-17 CN32 1-564-505-11 PLUG, CONNECTOR 2P
D992 8-719-913-42 DIODE 1N4002T
D993 8-719-913-42 DIODE 1N4002T < DIODE >
D994 8-719-913-42 DIODE 1N4002T
D995 8-719-913-42 DIODE 1N4002T 0 D1 8-719-077-77 DIODE D3SB60F3
0 D11 8-719-979-64 DIODE UF4005/23
< IC > 0 D12 6-501-178-01 DIODE UDZW-TE17-15B
0 D13 6-501-178-01 DIODE UDZW-TE17-15B
IC991 6-704-135-01 IC MM1614A 0 D14 8-719-063-74 DIODE D1NL20U-TR2

< TRANSISTOR > 0 D15 6-501-178-01 DIODE UDZW-TE17-15B

0 D16 6-501-178-01 DIODE UDZW-TE17-15B
Q991 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF 0 D17 8-719-060-48 DIODE RB751V-40TE-17
D31 6-501-320-01 DIODE FCQ10A04
< RESISTOR > D32 8-719-074-58 DIODE FCH10A10

R991 1-216-825-11 METAL CHIP 2.2K 5% 1/10W D33 8-719-983-23 DIODE MTZJ-T-77-27B
R992 1-216-845-11 METAL CHIP 100K 5% 1/10W D34 8-719-923-91 DIODE MTZJ-T-77-16A

< RELAY > < FUSE >

0 RY990 1-755-467-31 RELAY (POWER) 0 F1 1-576-230-51 FUSE (T3.15AL/H250V)

0 RY991 1-755-467-31 RELAY (POWER)
< FERRITE BEAD >
< TRANSFORMER >
0 FB11 1-410-397-21 FERRITE 1.1uH
0 T991 1-437-676-11 TRANSFORMER, POWER
************************************************************ < FUSE HOLDER >

SW POWER BOARD FH1 1-533-399-21 FUSE HOLDER

**************** FH2 1-533-399-21 FUSE HOLDER

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S < IC >

< CAPACITOR > 0 IC11 6-707-749-01 IC CXD9841P

0 C1 1-165-529-11 MYLAR 0.22uF 10 275V < PHOTO COUPLER >

0 C3 1-165-528-11 MYLAR 0.1uF 10 275V
0 C4 1-119-886-51 CERAMIC 470PF 10% 250V 0 PH11 6-600-187-01 PHOTO COUPLER PC123Y22JOOF
0 C5 1-119-886-51 CERAMIC 470PF 10% 250V
0 C11 1-100-923-21 ELECT 100uF 20% 450V < FET >

0 C13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V 0 Q11 6-551-319-01 FET 2SK3563 (LB2SONY)
0 C14 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V 0 Q12 6-551-319-01 FET 2SK3563 (LB2SONY)
0 C15 1-126-965-11 ELECT 22uF 20% 50V

79
HCD-CPZ1DAB
SW POWER TC

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR > C644 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C645 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
0 R2 1-219-759-11 METAL 1M 5% 1/2W C646 1-130-483-00 MYLAR 0.01uF 5% 50V
0 R10 1-218-895-11 METAL CHIP 100K 0.5% 1/10W C651 1-104-664-11 ELECT 47uF 20% 25V
0 R12 1-245-478-21 METAL 470K 1% 1/4W C653 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
0 R13 1-245-478-21 METAL 470K 1% 1/4W
0 R14 1-218-869-11 METAL CHIP 8.2K 0.5% 1/10W C656 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C657 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
0 R15 1-218-875-11 METAL CHIP 15K 0.5% 1/10W C658 1-126-961-11 ELECT 2.2uF 20% 50V
0 R16 1-218-823-11 METAL CHIP 100 0.5% 1/10W C660 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
0 R17 1-211-989-11 METAL CHIP 68 0.5% 1/10W C661 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
0 R18 1-216-833-11 METAL CHIP 10K 5% 1/10W
0 R19 1-249-393-11 CARBON 10 5% 1/4W C662 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C663 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
0 R20 1-216-833-11 METAL CHIP 10K 5% 1/10W C664 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
0 R21 1-249-393-11 CARBON 10 5% 1/4W C665 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
0 R22 1-249-417-11 CARBON 1K 5% 1/4W C667 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
0 R23 1-243-979-71 METAL OXIDE 0.1 5% 2W
0 R24 1-216-821-11 METAL CHIP 1K 5% 1/10W C681 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

0 R25 1-247-694-11 CARBON 33 5% 1/4W < CONNECTOR >

R32 1-216-821-11 METAL CHIP 1K 5% 1/10W
R33 1-216-817-11 METAL CHIP 470 5% 1/10W CN603 1-784-780-11 CONNECTOR, FFC 19P

< TRANSFORMER > < DIODE >

0 T1 1-443-673-11 TRANSFORMER, LINE FILTER D641 6-501-193-01 DIODE 1SS355WTE-17

0 T2 1-443-673-11 TRANSFORMER, LINE FILTER D681 6-501-193-01 DIODE 1SS355WTE-17
0 T31 1-443-620-11 TRANSFORMER, CONVERTER
< FLAT CABLE >
< THERMISTOR >
FFC601 1-831-992-11 CABLE, FLEXIBLE FLAT (8 CORE)
0 TH1 1-803-806-31 THERMISTOR, NTC
< IC >
< GROUND TERMINAL >
IC601 6-702-130-01 IC HA12237F
TK1 1-537-771-21 TERMINAL BOARD, GROUND
TK2 1-537-771-21 TERMINAL BOARD, GROUND < COIL >
************************************************************
L601 1-410-780-11 INDUCTOR 27mH
TC BOARD L651 1-410-780-11 INDUCTOR 27mH
*********
< TRANSISTOR >
< CAPACITOR >
Q601 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF
C601 1-104-664-11 ELECT 47uF 20% 25V Q602 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF
C603 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q638 8-729-620-33 TRANSISTOR 2SA1235TP-1EF
C606 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V Q640 8-729-038-23 TRANSISTOR RT1N141C-TP-1
C607 1-162-962-11 CERAMIC CHIP 470PF 10% 50V Q642 8-729-036-95 TRANSISTOR KTC3198GR-A
C608 1-126-961-11 ELECT 2.2uF 20% 50V
Q643 8-729-036-95 TRANSISTOR KTC3198GR-A
C610 1-162-962-11 CERAMIC CHIP 470PF 10% 50V Q651 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF
C611 1-162-927-11 CERAMIC CHIP 100PF 5% 50V Q652 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF
C612 1-162-919-11 CERAMIC CHIP 22PF 5% 50V Q680 8-729-038-23 TRANSISTOR RT1N141C-TP-1
C613 1-162-962-11 CERAMIC CHIP 470PF 10% 50V Q681 8-729-038-12 TRANSISTOR RT1P141C-TP-1
C614 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
Q688 8-729-038-23 TRANSISTOR RT1N141C-TP-1
C615 1-162-919-11 CERAMIC CHIP 22PF 5% 50V Q691 8-729-038-23 TRANSISTOR RT1N141C-TP-1
C617 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q692 8-729-038-23 TRANSISTOR RT1N141C-TP-1
C631 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V Q693 8-729-040-76 TRANSISTOR KTA1273-Y-AT
C632 1-126-964-11 ELECT 10uF 20% 50V Q694 8-729-040-76 TRANSISTOR KTA1273-Y-AT
C633 1-126-964-11 ELECT 10uF 20% 50V
< RESISTOR >
C634 1-126-964-11 ELECT 10uF 20% 50V
C635 1-126-960-11 ELECT 1uF 20% 50V R601 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
C641 1-104-664-11 ELECT 47uF 20% 25V R602 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
C642 1-137-393-11 FILM 0.01uF 5% 100V R603 1-216-821-11 METAL CHIP 1K 5% 1/10W
C643 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R605 1-216-841-11 METAL CHIP 47K 5% 1/10W
R606 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

80
 HCD-CPZ1DAB
Ver. 1.1
TC

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R607 1-216-833-11 METAL CHIP 10K 5% 1/10W MISCELLANEOUS

R608 1-216-829-11 METAL CHIP 4.7K 5% 1/10W **************
R609 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R610 1-216-833-11 METAL CHIP 10K 5% 1/10W 62 1-796-456-41 DECK, MECHANICAL (CMAL1Z255A)
R611 1-216-837-11 METAL CHIP 22K 5% 1/10W 0 201 1-751-520-31 CORD, POWER
207 1-693-626-11 TUNER (FM/AM)
R612 1-216-833-11 METAL CHIP 10K 5% 1/10W 252 1-830-386-21 CORD (WITH CONNECTOR) (for Venice 1.1)
R613 1-216-825-11 METAL CHIP 2.2K 5% 1/10W 254 1-400-932-11 FILTER, CLAMP
R614 1-216-845-11 METAL CHIP 100K 5% 1/10W
R616 1-216-809-11 METAL CHIP 100 5% 1/10W 255 1-478-669-11 MODULE (DAB TUNER) (Venice 1.1)
R617 1-216-833-11 METAL CHIP 10K 5% 1/10W 260 1-500-082-21 CLAMP, SLEEVE FERRITE
462 1-452-925-41 MAGNET ASSY
R622 1-216-801-11 METAL CHIP 22 5% 1/10W 0 556 A-4735-357-A OPTICAL PICK-UP BLOCK (KSM-213DHAP)
R623 1-216-801-11 METAL CHIP 22 5% 1/10W 559 1-827-992-11 WIRE (FLAT TYPE) (16 CORE)
R624 1-216-801-11 METAL CHIP 22 5% 1/10W
R625 1-216-801-11 METAL CHIP 22 5% 1/10W CN3 1-815-550-11 PIN, CONNECTOR (PWB) 2P
R630 1-216-857-11 METAL CHIP 1M 5% 1/10W FFC301 1-831-950-21 CABLE, FLEXIBLE FLAT (19 CORE)
FFC302 1-832-874-21 CABLE, FLEXIBLE FLAT (21 CORE)
R631 1-216-837-11 METAL CHIP 22K 5% 1/10W FFC308 1-832-756-21 CABLE, FLEXIBLE FLAT (23 CORE)
R632 1-216-821-11 METAL CHIP 1K 5% 1/10W FFC309 1-831-943-21 CABLE, FLEXIBLE FLAT (15 CORE)
R633 1-216-833-11 METAL CHIP 10K 5% 1/10W
R635 1-216-809-11 METAL CHIP 100 5% 1/10W FFC310 1-832-816-21 CABLE, FLEXIBLE FLAT (9 CORE)
R640 1-216-825-11 METAL CHIP 2.2K 5% 1/10W FFC901 1-831-952-21 CABLE, FLEXIBLE FLAT (19 CORE)
FFC951 1-832-806-21 CABLE, FLEXIBLE FLAT (7 CORE)
R643 1-216-793-11 METAL CHIP 4.7 5% 1/10W M701 A-1148-845-A MOTOR ASSY (LOADING)
R644 1-216-793-11 METAL CHIP 4.7 5% 1/10W S201 1-771-853-11 SWITCH, DETECTION (LIMIT)
R645 1-216-837-11 METAL CHIP 22K 5% 1/10W
R646 1-216-837-11 METAL CHIP 22K 5% 1/10W
R647 1-216-837-11 METAL CHIP 22K 5% 1/10W

R648 1-216-833-11 METAL CHIP 10K 5% 1/10W

R651 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R652 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R653 1-216-821-11 METAL CHIP 1K 5% 1/10W
R655 1-216-841-11 METAL CHIP 47K 5% 1/10W

R656 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R657 1-216-833-11 METAL CHIP 10K 5% 1/10W
R658 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R659 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R660 1-216-833-11 METAL CHIP 10K 5% 1/10W

R661 1-216-837-11 METAL CHIP 22K 5% 1/10W

R662 1-216-833-11 METAL CHIP 10K 5% 1/10W
R663 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R664 1-216-845-11 METAL CHIP 100K 5% 1/10W
R681 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R682 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R683 1-216-821-11 METAL CHIP 1K 5% 1/10W
R684 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R685 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R687 1-216-841-11 METAL CHIP 47K 5% 1/10W

R688 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R689 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R690 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R691 1-216-833-11 METAL CHIP 10K 5% 1/10W
R692 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R693 1-216-841-11 METAL CHIP 47K 5% 1/10W

R694 1-216-837-11 METAL CHIP 22K 5% 1/10W
R695 1-216-833-11 METAL CHIP 10K 5% 1/10W

< TRANSFORMER >

T601 1-423-980-11 TRANSFORMER, BIAS OSCILLATION

************************************************************

81
HCD-CPZ1DAB

MEMO

82
 HCD-CPZ1DAB

HCD-CPZ1DAB 2. DIAGRAMS
• Note for Printed Wiring Boards and Schematic Diagrams

Note on Printed Wiring Board: Note on Schematic Diagram:

• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF)
UK Model • Y : parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics
• f : internal component. and tantalums.
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise

SERVICE MANUAL
(The other layers' patterns are not indicated.) specified.
• Indication of transistor. • f : internal component.
• A : B+ Line.
C • Voltages and waveforms are dc with respect to ground
Q These are omitted. under no-signal (detuned) conditions.
Ver. 1.1 2006.10 B E
no mark : TUNER
( ) : CD PLAY
〈〈 〉〉 : TAPE PLAY
{ } : TAPE REC
• Voltages are taken with a VOM (Input impedance 10 MΩ).
SUPPLEMENT-1
Q
Voltage variations may be noted due to normal produc-
B C E tion tolerances.
File this supplement with the service manual. • Signal path.
These are omitted. F : TUNER (FM/AM)
f : TUNER (DAB)
Subject: Change of MAIN board (Suffix-13) E : TAPE PLAY
a : TAPE REC
J : CD PLAY (ANALOG)
c : CD PLAY (DIGITAL)
j : AUX IN

In this set, MAIN board has been changed in the midway of production.
Printed wiring board and schematic diagrams of new type, and changed
parts list are described in this supplement-1.
Refer to original service manual for other information.

1. NEW/FORMER DISCRIMINATION
– MAIN BOARD (Component Side) –

Former : 1-870-842-12
New : 1-870-842-13

9-887-335-81
HCD-CPZ1DAB
1
HCD-CPZ1DAB

2-1. SCHEMATIC DIAGRAM – MAIN Board (1/2) –

CN301
19P
M+12V
(1/2) MGND
INPUT SELECT,ELECTRICAL VOLUME
27 TRIG SOL
IC501
C503
220 C527 BD3872FS 28 CAP MOT
10V 0.1
R523 1k 50 +3.3V
GND SC
+7V REGULATOR
R522 1k 51 91 END-SW
FILTER SI IC201
TA7807S 92 HALF.REC
E2 VCC FFC301
73 PLAY SW
C501
E1 CAP 0.1 O G I
C564 1 50V C555 10 50V 75 BIAS-ON
D203

-MD-
D2 OUT2
C514 1 50V C505 10 50V C217 C202 1N4002T 33 REC/PB
1 0.1
D1 OUT1
JW402 C556 0.1 R566 D204 34 LINE-MUTE
C2 BOUT2

-ST-
4.7k 1N4002T
JW401 R556 220k C557 0.1 38 REC-MUTE
C1 BNF2
C561 10 50V C506 0.1 39 ALC

C513 220 16V

B2 BOUT1 R516 D205 Refer to page

-CD-
CN302 4.7k 1N4002T 27 on service
C511 10 50V R506 220k C507 0.1 PB-R
21P B1 BNF1
+4V REGULATOR manual
A+5V C562 1 50V C558 0.0022 REC-R
A2 TNF2 IC202

-TC-
D202
AGND C512 1 50V C508 0.0022 TA7804LS PB-L
1N4002T
A1 TNF1
R IN C560 1 50V REC-L
SEL2 SOUT2 O G I
AGND C559 A-GND
1 VIN2 SQI2
L IN 50V C218 C204 A+9V
1 0.1
SEL1 SOUT1
P DOWN C510 C509 VIN1 SQI1
FFC302 1
1
DGND R509 50V 50V
10k
D+3.3V

INIT 40

NSP MUTE 41

DGND
A1
SC LATCH 42 TUNER SELECTOR
IC421 A2
Refer to page SC SHIFT 43 MC14052 C524 2200p
34 on service A3
SC DT 44 B C574 2200p
manual A4
GND
/SD 45

DGND
A
VEE
C432
0.1
R436
100 (Page 3)
X3
INH
/RST 46 R438 100k
X0 R453 R551 R501
Y1 10k 1k 1k
SOFT MUTE 47 R432 100k
X Q463 C209
Y3 2SC5938 470
PG MUTE 48
X1 Q402 10V
Y RT1P141C +5V REGULATOR
OVF R434 100k
X2 R403
IC204
/OTW Y2 10k Q401,402 MM1615ANLE
VCC Q413 C208
Y0
2SC5938 MUTING CONTROL 0.1
R435 Q413,463 IN
CN303 470 CONT
7P R511 R512 MUTING GND
1k 10k
MD L R421 100k
CN
Q401 OUT
MD GND R422 100k
R561 R562 RT1N141C C216
1k 10k 0.01
MD R
Q422 Q421
HP DET 54 R437 100k 52
C431 RT1N441C RT1N441C
0.1
HP L INVERTER INVERTER

HP GND R433 100k

HP R 59 +9V REGULATOR
Refer to page R552
IC203
43 on service 10k R502
10k 58 TA7809S
manual CN310
9P
O I
G
DAB-L C421 1 50V R431 100k C554 C504
1 1 C207
FFC310 C206
A-GND 50V 50V 470
0.1
10V
DAB-R C422 1 50V 49

DAB 7V

DAB3.3V_ON

DAB5.0V_ON 57 CN202
L201 2P
0
DAB-DGND R553 12V
Refer to page 1k
DAB-S1DI 31 R414 R415 R455 Q551 GND
29 on service
100 22 100k KTC3198GR
manual DAB-S1DO 32
REGULATOR
R558 +12V REGULATOR Refer to page
56
Q412 22k IC200 35 on service
CN304 2SA1235EF R563
7P R413 JR401 C565 100
BAJ2DD0T manual
22 0 10 HEADPHONE AMP CN201
LED 5V
FFC951 50V FB200 2P
IC502 O G I 1.1UH
LCD CS 78 NJM4580MD C552 C550 C201 C200 16V
R503 R404 R559 R550 C214
10 22 4700 1
LCD SCL 36 R410 R554 1k 100k 22k 50V 50V 22k 16V 0.1 50V GND
Q411,412 10k 4.7k
G
LCD DATA 35 LED
Refer to page
BRIGHTNESS R555
LCD RESB 63 R411 D410 22k 45 on service
CONTROL 1N4002T
LCD+3.3V
2.2k manual
V R505 R504 C515
22k 4.7k 10
Refer to page DGND
C567 50V
39 on service 220
Q411 10V
manual CN305 RT1N141C
19P
R557
+7V
47 Q404
LED GND RT1P141C

LED TAPE 65
Q464 Q403
E+3.3V R560 2SC5938 RT1N141C 53
100k
SIRCS 4 R456 C519 C518
100
1k 0.1
DGND 16V

LED TUNER 66
FFC901 Q403,404
Q414
LED CD 67
R510 2SC5938 MUTING CONTROL
100k
NC
R406
VOLUME A 68 1k

VOLUME B 69
Q414,464 R507 C517
47 220
FOLDER A 70 MUTING 10V
A5
Refer to page FOLDER B 71
A6
41 on service KEY2 94
manual A7
KEY1 95
A8
KEY0 97
A9
LED STANDBY 72
A10
TREBLE 89
A11
BASS 90
A12

A13
(Page 3)
A14

HCD-CPZ1DAB
2 2
 HCD-CPZ1DAB

2-2. SCHEMATIC DIAGRAM – MAIN Board (2/2) –

(2/2)

R477 10k

R476 10k

R471 10k

R470 10k

R469 10k

R468 10k

R457 10k

R454 10k
R474 1M
A1
D302
A2 MC2836

A3

54

52
80

63

58
68

65

60

59

56
69

66

51
73

61
78

75

70

57
79

76

67
71
77

72

53
(Page 2) A4
CN309
15P
26 RDS DATA

C362 0.1
18 RDS INT

R380 100

R379 100

R378 100

R377 100

R376 100

R374 100

R373 100

R372 100

R371 100

R370 100

R369 100

R368 100

R367 100

R366 100

R365 100

R362 100

R361 100

R360 100

R357 100

R355 100

R354 100
R356 10k
CN306
FM SIGNAL OUT
7P D308
MGND 1N4002T RDS +3.3V

RIN(NEG) 80 2 ST MUTE FM 75Ω

COAXIAL
FIN(POS) 79 C322 1 50V R OUT

M+7V C359 0.01 AGND FFC309

TUNER (FM/AM) ANTENNA
SW3(TRIGGER SW) C321 1 50V L OUT
SUPPLIED WITH
SW1(OUT SW) 77 STEREO
THE ASSEMBLED
SW2(CHUCK SW) 76 25 C309 0.01 TUNED BLOCK
Refer to page
30 on service C351 0.1 +9V AM
manual CN307 D303 R439
24 CE
3P MC2836 10k

LOAD

WAKE UP KEY
CDM SW2 (CLOSE)

VOLUME A

HP DET

AMP
LED TAPE

VSS

SI
LCD RESB

DAB-P0WER3.3
VOLUME B

LED TUNER

DAB SELECTOR SW

DAB-POWER5.0
TC PLAY

LED STAND BY

FOLDER A

VDD

STEREO IN
CD DATA
CDM SW1 (OPEN)

TC BIAS ON
CDM LOAD OUT

FOLDER B

LED CD

DAB-MUTE

LINE MUTE
CD SENS

HP MUTE
IN

LCD CS
CDM
DGND 23 DI

D+3.3V L491 0 22 DO
50
CD POWER
D OUT ON/OFF AMP SC 21 CLK
82 R382 100 R349 1k 49
R547 CD XTACN LCD_ON
83 R383 100 R348 100 48
CN308 220
CD XRST S-MASTER PG MUTE EP201
23P 84 R384 100 R347 100 47
Refer to page CD DATA 60 MP3 IREQ S-MASTER SOFT MUTE
43 on service 85 R385 100 R346 100 46
MP3 CLK 7 MP3 XLAT S-MASTER RST
manual 86 R386 100 R345 100 45
D306
1SS355W
DR MUTE 3 MP3 REQ KEY0 S-MASTER SD EP302
87 R387 100 R344 100 44
D+3.3V L493 0 MP3 ACK VREF S-MASTER DATA
88 R388 100 R343 100 43
D OUT CD XLAT AVDD S-MASTER SHIFT
D307
89 R389 100 SYSTEM CONTROLLER R342 100 42
POWER RELAY 1SS355W
DGND R440 D406 TREBLE ON/OFF IC301 S-MASTER LATCH
FFC308 90 R390 100 R341 100 41
1k 1N4002T M30624MGP
L OUT BASS S-MASTER NSP MUTE EP301

PROTECT2
A59FPU0 C215

DR MUTE
91 R391 100 R340 100 40

ST MUTE
0.1
AGND TC END SW S-MASTER INIT

POWER

SIRCS
92 R392 100 R339 100 39
R OUT R490 1k TC HALF/REC SW ALC
R493 4.7k R338 100 38 C210
0.1 (CHASSIS)
A+3.3V L492 0 SPEC IN TC REC MUTE
94 R494 10k R394 100 R337 100 37
CD XTACN 82 KEY2 CD CLK
C211
95 R495 10k R395 100 R336 100 36 0.1
CD XRST 83 KEY1 LCD-CLK
C405 0.1 R335 100 35
MP3 IREQ 84 AVSS LCD DATA
C212
97 R497 10k R397 100 R334 100 34 D301
CD CLK 37 TC LINE MUTE MC2836 0.1
Refer to page R333 100 33

MP3 DATA OUT

25 on service MP3 DATA 5 TC PB/REC SW

ST DATA OUT
MP3 DATA IN
R332 100 32
manual C407

ST DATA IN
MP3 XLAT 85 DAB-DI

RDS DATA
0.1

TUNED IN
R331 100 31

CD SCOR

TC CAPM
MP3 CLK

RDS INT
MP3 REQ 86 DAB-DO

TC TRG
AC CUT

IIC CLK
CN VSS

ST CLK
XCOUT

RESET

ST CE
XOUT
R428 R427 CN300

CNT1

DATA
BYTE

XCIN
MP3 ACK 87

VDD

NMI
VSS
10k 10k 3P

XIN

IIC
CD XLAT 88 RELAY ON
R400
100
CD SENS 61 4V(EVER)

CD SCOR 19 GND

MGND

M+7V Refer to page

CN400 47 on service
L411 R330 4P
D405 0 100 manual
1N4002T

R311 100k
R405 22k

R302 100

R303 100

R304 100

R305 100

R306 100

R307 100

R319 100

R320 47k

R321 100

R322 100

R323 100

R324 100

R325 100

R327 100

R328 100
R301 10k

R309 10k

R417 10k

R429 10k
A5

R313 0
NC
A6 R329
100

6.3V
A7
R430
10k
C311 22p

C301 1000
A8 4
32.768KHz

R412 10k

R425 10k
C316 0.1
X301

A9

A10
C310

19
A11
22p RESET SIGNAL GENERATOR
3

(Page 2) A12

A13

A14
R420
10k IC302 C402
PST3629NR
R318 100

R326 100
C312 0.1
0.1
R401 C404 OUT
47k 0.1 CD
VDD
Q301
2SC3052F X302 GND
RESET 16MHz NC
D305 R402 C403 C401

27

28
SWITCH
18

1SS355W 47k 0.1 0.1

2

21

22

24
23

25

26

HCD-CPZ1DAB
3 3
HCD-CPZ1DAB
2-3. PRINTED WIRING BOARD – MAIN Board – :Uses unleaded solder.

• Semiconductor 1 2 3 4 5 6 7 8 9 10 11
Location
Ref. No. Location TC BOARD AMP BOARD DAB BOARD
CN603
B D CN700
R CNS801
D202 C-6 MAIN BOARD Refer to page
26 on service
Refer to page Refer to page
28 on service
D203 C-8 A FFC301
manual
FFC302
36 on service
manual
FFC310
manual

D204 B-9 C562 CN301

D205 B-9

C508

C507

C557
HT201
D301 F-7

JW289
C560
D302 F-7

JW202
JW201
JW295
JW294
R516 R566 E

R502
D303 H-9 C505 Q413 R403
C512
D305 I-9 R501 R453

JW296
D204
E JW290
D306 I-11 R506 R556 C555 JW354 Q401 JW291

C208
D307 I-10 B R551
C510
JW288
C209
C216 JW286

C558

C506

C556
D308 I-8 R552 Q402 3 1
IC203 IC200

JW203
JW214
E JW292 C207 EP201
E
D405 E-6 Q463

D205
JW350 3 1 C200
C501 4 5
D406 E-5

JW360
C513
C509 IC501 JW351 IC204 JW213
D410 F-2 JW356
JW293 (CHASSIS)

C206
1

JW298
3

JW299
JW357

JW297
C527

R523
CN302

D203
JW363

JW392
JW300
IC200 B-9

JW287
JW383
JW381
C559
C554 C504 C214
IC202

JW323
IC201 D-8 C561

JW353
C511

JW355
C503

JW285
IC202 C-8 C R522 R509
D202 3
FB200
C574
IC203 B-8

R550
C524 C565

C218
IC204 B-7

R559
JW393

JW283

C204
C552 1
IC301 G-10

R563
JW394

JW282
JW391
C550 JW307

JW279

HT200

JW396
JW388

JW397
R554
IC302 I-10 R553

JW401

JW204
R558

Q551
JW402
C567 IC201

JW216
R555 R455
IC421 E-2 C514 C564
C518 E Refer to page
C202 JW395
IC501 B-3 3

C519
44 on service

JW314
JW284
JW281
JW280
JW389

JW362
CN201

JW328
manual

JW373
JW371
C217
IC502 D-3 R436
2
C322
IC502 1
H

JW325

JW361
C432

JW221
JW410 1 JW205
D C517 C201 JW206

JW358
JW309
JW310

JW330
JW316
JW315
SW POWER

JW225
C515
Q301 I-10

R432
R505 R404 JR401 BOARD

CN202
JW412 JW411 E 1 JW207
L201 CN32
R503
Q401 B-4 R504 Q403 2
J

R434
Q402 B-4 E R438 JW370 R557 R406 E JW208
AMP BOARD
CN310
Q403 D-5 Q422 IC421 E R510 R456 Q404 JW209 CN705

R507
Q414 Refer to page
Q404 D-4 E
Q464 JW222

JW278
JW277
JW276
R560 36 on service

R562
JW415
JW413
JW414

JW275
C431
E
Q411 F-3 Q421 R561 JW231 manual

JW227
JW226

JW223

JW224
JW331
R512
1 CN303 7
Q412 F-2 R435 JW306

JW374
JW372

JW369
R421 JW263
JW317
Q413 B-3 R422
R511 JW303
R431 JW319
Q414 E-3 E R437

JW382
E JW416
JW320 JW210 C
R433
Q421 E-2 C321 D406 JW229

D405
JW313 JW321 JW211 DRIVER
HP/MD

JW365
BOARD
Q422 D-2 R477

JW318
BOARD JW312 JW230 JW217 JW220 JW322
JW326 R476 CN701
NO982 C421
Q463 B-3 Refer to page
JW417 C422 JW311 JW368
JW232 JW215 JW212 Refer to page
30 on service

JW274
JW273
JW272

JW271
JW270
Q464 E-4 42 on service JW385
7 CN306 1 manual
manual CN305
Q551 C-4 JW304 JW343 JW305 JW233 JW346 JW341 JW327

L411

R380

R378
R376
JW386 JW234
JW344 R440 JW269 JW347 JW342 R439 JW338

JW379
R415
R411

JW418 R410 E JW268

JW380
R547 JW329 R490 JW235 JW219 JW218 JW345 JW339

R379

R374
JW308

R377
3 1

R349
R347

R343
R341
R339
R337
R335
E
F L491 R427

R356
JW267 JW236 R469
3 1 R470

R457

R454
JW377
JW375
R414 Q411 CN300 R428
R413 JW237 R471 R468 R334
Q412 C215 CN307 23 CN308 1

R362
L492 R345 R333

R373
JW238
CN304

22 2 R332
C211

R370
L493

JW340

R354
JW239

R368

R355
D410 A D301 A R360 R331

R366
C210

R348
R346
R344
R342
R340
R338
R336
JW349 D302 R328

R357
JW240
JW387

51

R372
JW332 K K K K R361 50 R327
JW324

R369
R371
JW334
JW333

JW265

JW264

R367
C212 JW241

JW398

R365
JW337

JW336
JW335
JW266
C362
EP301 R430
JW242
IC301 31
R330

JW244

JW243

(FOR CHECK)
R329 1
G

CN400
30
FFC951 FFC901 80
LCD BOARD PANEL BOARD 4
F CN951 G CN901
FFC308
81 R429
CD BOARD SUB POWER
Refer to page Refer to page
A L R383 R382

R417
38 on service 40 on service (CHASSIS) CN102 BOARD X302 JW245
OPT R385 R384
K

R320
R313
manual manual Refer to page NO992

R311
JW348

R323
BOARD 24 on service Refer to page R387 R386 R325
NO981

JW352
manual 46 on service R389 R388
Refer to page manual 100 1 C316
R390

R322
42 on service X301 R326

R318
manual R391
R392 A D303 C407
C301 R425

R303
R305
R474 C405

JW251
R494 K K C311 R321
R324

R400
H R495
R394

JW252

R304
R306
R395

R309
C310
R302
JW248
R493 JW247
R397 JW249

R497
JW257
JW250
R405 R307

JW256

JW255
R402

D305
C312
Q301

JW253
JW259
JW258
R301 E R412

JW254
R319

R401

C403
R420
C404
JW260

JW359
C351
C309
JW378

C359 JW261
I CN309 C401
JW262
FFC309 3 1

D307
D306
C402
JW376
FM 75Ω TUNER 4 5
COAXIAL
(FM/AM)
SUPPLIED
D308 IC302
ANTENNA 13
WITH THE
ASSEMBLED 1-870-842- (13)
AM EP302
BLOCK

(CHASSIS)

HCD-CPZ1DAB
4 4
 HCD-CPZ1DAB
MAIN
3. ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they When indicating parts by reference
parts list may be different from the parts are seldom required for routine service. number, please include the board.
specified in the diagrams or the components Some delay should be anticipated when
used on the set. ordering these items.
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS
may have some difference from the original In each case, u: µ, for example:
one. uA... : µA... uPA... : µPA...
• RESISTORS uPB... : µPB... uPC... : µPC...
All resistors are in ohms. uPD... : µPD...
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF
F: nonflammable • COILS
uH: µH

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-1193-279-A MAIN BOARD, COMPLETE C503 1-126-934-11 ELECT 220uF 20% 16V
********************* C504 1-126-960-11 ELECT 1uF 20% 50V

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S C505 1-126-964-11 ELECT 10uF 20% 50V
C506 1-136-497-81 FILM 0.1uF 5% 50V
< CAPACITOR > C507 1-136-497-81 FILM 0.1uF 5% 50V
C508 1-130-475-00 MYLAR 0.0022uF 5% 50V
C200 1-126-960-11 ELECT 1uF 20% 50V C509 1-126-960-11 ELECT 1uF 20% 50V
C201 1-126-937-11 ELECT 4700uF 20% 16V
C202 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C510 1-126-960-11 ELECT 1uF 20% 50V
C204 1-164-156-11 CERAMIC CHIP 0.1uF 25V C511 1-126-964-11 ELECT 10uF 20% 50V
C206 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C512 1-126-960-11 ELECT 1uF 20% 50V
C513 1-126-934-11 ELECT 220uF 20% 16V
C207 1-126-935-11 ELECT 470uF 20% 16V C514 1-126-960-11 ELECT 1uF 20% 50V
C208 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C209 1-126-935-11 ELECT 470uF 20% 16V C515 1-126-964-11 ELECT 10uF 20% 50V
C210 1-164-156-11 CERAMIC CHIP 0.1uF 25V C517 1-126-934-11 ELECT 220uF 20% 16V
C211 1-164-156-11 CERAMIC CHIP 0.1uF 25V C518 1-126-933-11 ELECT 100uF 20% 16V
C519 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C212 1-164-156-11 CERAMIC CHIP 0.1uF 25V C524 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C214 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C215 1-164-156-11 CERAMIC CHIP 0.1uF 25V C527 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C216 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C550 1-126-965-11 ELECT 22uF 20% 50V
C217 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C552 1-126-964-11 ELECT 10uF 20% 50V
C554 1-126-960-11 ELECT 1uF 20% 50V
C218 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C555 1-126-964-11 ELECT 10uF 20% 50V
C301 1-126-916-11 ELECT 1000uF 20% 6.3V
C309 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C556 1-136-497-81 FILM 0.1uF 5% 50V
C310 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C557 1-136-497-81 FILM 0.1uF 5% 50V
C311 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C558 1-130-475-00 MYLAR 0.0022uF 5% 50V
C559 1-126-960-11 ELECT 1uF 20% 50V
C312 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C560 1-126-960-11 ELECT 1uF 20% 50V
C316 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C321 1-126-960-11 ELECT 1uF 20% 50V C561 1-126-964-11 ELECT 10uF 20% 50V
C322 1-126-960-11 ELECT 1uF 20% 50V C562 1-126-960-11 ELECT 1uF 20% 50V
C351 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C564 1-126-960-11 ELECT 1uF 20% 50V
C565 1-126-964-11 ELECT 10uF 20% 50V
C359 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C567 1-126-934-11 ELECT 220uF 20% 16V
C362 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C401 1-164-156-11 CERAMIC CHIP 0.1uF 25V C574 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C402 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C403 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < CONNECTOR >

C404 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN201 1-564-505-11 PLUG, CONNECTOR 2P
C405 1-164-156-11 CERAMIC CHIP 0.1uF 25V CN202 1-815-443-11 PIN, CONNECTOR (PWB) 2P
C407 1-164-156-11 CERAMIC CHIP 0.1uF 25V CN300 1-815-444-11 PIN, CONNECTOR (PWB) 3P
C421 1-126-960-11 ELECT 1uF 20% 50V CN301 1-784-780-11 CONNECTOR, FFC 19P
C422 1-126-960-11 ELECT 1uF 20% 50V CN302 1-784-782-11 CONNECTOR, FFC 21P

C431 1-164-156-11 CERAMIC CHIP 0.1uF 25V * CN303 1-815-448-11 PIN, CONNECTOR (PWB) 7P
C432 1-164-156-11 CERAMIC CHIP 0.1uF 25V CN304 1-784-768-11 CONNECTOR, FFC 7P
C501 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN305 1-784-780-11 CONNECTOR, FFC 19P

5
HCD-CPZ1DAB
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* CN306 1-815-448-11 PIN, CONNECTOR (PWB) 7P Q411 8-729-038-23 TRANSISTOR RT1N141C-TP-1
CN307 1-815-444-11 PIN, CONNECTOR (PWB) 3P Q412 8-729-620-33 TRANSISTOR 2SA1235TP-1EF
Q413 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
CN308 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P Q414 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
CN309 1-784-776-11 CONNECTOR, FFC 15P Q421 8-729-038-28 TRANSISTOR RT1N441C-TP-1
CN310 1-784-770-11 CONNECTOR, FFC 9P
Q422 8-729-038-28 TRANSISTOR RT1N441C-TP-1
< DIODE > Q463 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
Q464 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
D202 8-719-913-42 DIODE 1N4002T Q551 8-729-036-95 TRANSISTOR KTC3198GR-A
D203 8-719-913-42 DIODE 1N4002T
D204 8-719-913-42 DIODE 1N4002T < RESISTOR >
D205 8-719-913-42 DIODE 1N4002T
D301 6-500-334-01 DIODE MC2836-T112-1 R301 1-216-833-11 METAL CHIP 10K 5% 1/10W
R302 1-216-809-11 METAL CHIP 100 5% 1/10W
D302 6-500-334-01 DIODE MC2836-T112-1 R303 1-216-809-11 METAL CHIP 100 5% 1/10W
D303 6-500-334-01 DIODE MC2836-T112-1 R304 1-216-809-11 METAL CHIP 100 5% 1/10W
D305 6-501-193-01 DIODE 1SS355WTE-17 R305 1-216-809-11 METAL CHIP 100 5% 1/10W
D306 6-501-193-01 DIODE 1SS355WTE-17
D307 6-501-193-01 DIODE 1SS355WTE-17 R306 1-216-809-11 METAL CHIP 100 5% 1/10W
R307 1-216-809-11 METAL CHIP 100 5% 1/10W
D308 8-719-913-42 DIODE 1N4002T R309 1-216-833-11 METAL CHIP 10K 5% 1/10W
D405 8-719-913-42 DIODE 1N4002T R311 1-216-845-11 METAL CHIP 100K 5% 1/10W
D406 8-719-913-42 DIODE 1N4002T R313 1-216-864-11 SHORT CHIP 0
D410 8-719-913-42 DIODE 1N4002T
R318 1-216-809-11 METAL CHIP 100 5% 1/10W
< EARTH TERMINAL > R319 1-216-809-11 METAL CHIP 100 5% 1/10W
R320 1-216-841-11 METAL CHIP 47K 5% 1/10W
EP301 1-537-771-21 TERMINAL BOARD, GROUND R321 1-216-809-11 METAL CHIP 100 5% 1/10W
EP302 1-537-771-21 TERMINAL BOARD, GROUND R322 1-216-809-11 METAL CHIP 100 5% 1/10W

< FERRITE BEAD > R323 1-216-809-11 METAL CHIP 100 5% 1/10W
R324 1-216-809-11 METAL CHIP 100 5% 1/10W
FB200 1-410-397-21 FERRITE 1.1uH R325 1-216-809-11 METAL CHIP 100 5% 1/10W
R326 1-216-809-11 METAL CHIP 100 5% 1/10W
< IC > R327 1-216-809-11 METAL CHIP 100 5% 1/10W

IC200 6-709-978-01 IC BAJ2DD0T R328 1-216-809-11 METAL CHIP 100 5% 1/10W

IC201 8-759-071-48 IC TA7807S R329 1-216-809-11 METAL CHIP 100 5% 1/10W
IC202 6-703-546-01 IC TA7804LS R330 1-216-809-11 METAL CHIP 100 5% 1/10W
IC203 8-759-231-56 IC TA7809S R331 1-216-809-11 METAL CHIP 100 5% 1/10W
IC204 6-707-282-01 IC MM1615ANLE R332 1-216-809-11 METAL CHIP 100 5% 1/10W

IC301 6-806-756-01 IC M30624MGP-A59FPU0 R333 1-216-809-11 METAL CHIP 100 5% 1/10W

IC302 6-701-680-01 IC PST3629NR R334 1-216-809-11 METAL CHIP 100 5% 1/10W
IC421 8-759-367-79 IC MC14052BFEL R335 1-216-809-11 METAL CHIP 100 5% 1/10W
IC501 6-707-974-01 IC BD3872FS R336 1-216-809-11 METAL CHIP 100 5% 1/10W
IC502 8-759-656-83 IC NJM4580MD- (TE2) R337 1-216-809-11 METAL CHIP 100 5% 1/10W

< JUMPER RESISTOR > R338 1-216-809-11 METAL CHIP 100 5% 1/10W
R339 1-216-809-11 METAL CHIP 100 5% 1/10W
JR401 1-216-864-11 SHORT CHIP 0 R340 1-216-809-11 METAL CHIP 100 5% 1/10W
R341 1-216-809-11 METAL CHIP 100 5% 1/10W
< JUMPER RESISTOR > R342 1-216-809-11 METAL CHIP 100 5% 1/10W

L201 1-216-864-11 SHORT CHIP 0 R343 1-216-809-11 METAL CHIP 100 5% 1/10W
L411 1-216-864-11 SHORT CHIP 0 R344 1-216-809-11 METAL CHIP 100 5% 1/10W
L491 1-216-864-11 SHORT CHIP 0 R345 1-216-809-11 METAL CHIP 100 5% 1/10W
L492 1-216-864-11 SHORT CHIP 0 R346 1-216-809-11 METAL CHIP 100 5% 1/10W
L493 1-216-864-11 SHORT CHIP 0 R347 1-216-809-11 METAL CHIP 100 5% 1/10W

< TRANSISTOR > R348 1-216-809-11 METAL CHIP 100 5% 1/10W

R349 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q301 8-729-600-91 TRANSISTOR 2SC3052F-T1-LF R354 1-216-809-11 METAL CHIP 100 5% 1/10W
Q401 8-729-038-23 TRANSISTOR RT1N141C-TP-1 R355 1-216-809-11 METAL CHIP 100 5% 1/10W
Q402 8-729-038-12 TRANSISTOR RT1P141C-TP-1 R356 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q403 8-729-038-23 TRANSISTOR RT1N141C-TP-1
Q404 8-729-038-12 TRANSISTOR RT1P141C-TP-1 R357 1-216-809-11 METAL CHIP 100 5% 1/10W
R360 1-216-809-11 METAL CHIP 100 5% 1/10W

6
 HCD-CPZ1DAB
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R361 1-216-809-11 METAL CHIP 100 5% 1/10W
R362 1-216-809-11 METAL CHIP 100 5% 1/10W R436 1-216-809-11 METAL CHIP 100 5% 1/10W
R365 1-216-809-11 METAL CHIP 100 5% 1/10W R437 1-216-845-11 METAL CHIP 100K 5% 1/10W
R438 1-216-845-11 METAL CHIP 100K 5% 1/10W
R366 1-216-809-11 METAL CHIP 100 5% 1/10W R439 1-216-833-11 METAL CHIP 10K 5% 1/10W
R367 1-216-809-11 METAL CHIP 100 5% 1/10W R440 1-216-821-11 METAL CHIP 1K 5% 1/10W
R368 1-216-809-11 METAL CHIP 100 5% 1/10W
R369 1-216-809-11 METAL CHIP 100 5% 1/10W R453 1-216-833-11 METAL CHIP 10K 5% 1/10W
R370 1-216-809-11 METAL CHIP 100 5% 1/10W R454 1-216-833-11 METAL CHIP 10K 5% 1/10W
R455 1-216-845-11 METAL CHIP 100K 5% 1/10W
R371 1-216-809-11 METAL CHIP 100 5% 1/10W R456 1-216-821-11 METAL CHIP 1K 5% 1/10W
R372 1-216-809-11 METAL CHIP 100 5% 1/10W R457 1-216-833-11 METAL CHIP 10K 5% 1/10W
R373 1-216-809-11 METAL CHIP 100 5% 1/10W
R374 1-216-809-11 METAL CHIP 100 5% 1/10W R468 1-216-833-11 METAL CHIP 10K 5% 1/10W
R376 1-216-809-11 METAL CHIP 100 5% 1/10W R469 1-216-833-11 METAL CHIP 10K 5% 1/10W
R470 1-216-833-11 METAL CHIP 10K 5% 1/10W
R377 1-216-809-11 METAL CHIP 100 5% 1/10W R471 1-216-833-11 METAL CHIP 10K 5% 1/10W
R378 1-216-809-11 METAL CHIP 100 5% 1/10W R474 1-216-857-11 METAL CHIP 1M 5% 1/10W
R379 1-216-809-11 METAL CHIP 100 5% 1/10W
R380 1-216-809-11 METAL CHIP 100 5% 1/10W R476 1-216-833-11 METAL CHIP 10K 5% 1/10W
R382 1-216-809-11 METAL CHIP 100 5% 1/10W R477 1-216-833-11 METAL CHIP 10K 5% 1/10W
R490 1-216-821-11 METAL CHIP 1K 5% 1/10W
R383 1-216-809-11 METAL CHIP 100 5% 1/10W R493 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R384 1-216-809-11 METAL CHIP 100 5% 1/10W R494 1-216-833-11 METAL CHIP 10K 5% 1/10W
R385 1-216-809-11 METAL CHIP 100 5% 1/10W
R386 1-216-809-11 METAL CHIP 100 5% 1/10W R495 1-216-833-11 METAL CHIP 10K 5% 1/10W
R387 1-216-809-11 METAL CHIP 100 5% 1/10W R497 1-216-833-11 METAL CHIP 10K 5% 1/10W
R501 1-216-821-11 METAL CHIP 1K 5% 1/10W
R388 1-216-809-11 METAL CHIP 100 5% 1/10W R502 1-216-833-11 METAL CHIP 10K 5% 1/10W
R389 1-216-809-11 METAL CHIP 100 5% 1/10W R503 1-216-821-11 METAL CHIP 1K 5% 1/10W
R390 1-216-809-11 METAL CHIP 100 5% 1/10W
R391 1-216-809-11 METAL CHIP 100 5% 1/10W R504 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R392 1-216-809-11 METAL CHIP 100 5% 1/10W R505 1-216-837-11 METAL CHIP 22K 5% 1/10W
R506 1-216-849-11 METAL CHIP 220K 5% 1/10W
R394 1-216-809-11 METAL CHIP 100 5% 1/10W R507 1-216-805-11 METAL CHIP 47 5% 1/10W
R395 1-216-809-11 METAL CHIP 100 5% 1/10W R509 1-216-833-11 METAL CHIP 10K 5% 1/10W
R397 1-216-809-11 METAL CHIP 100 5% 1/10W
R400 1-216-809-11 METAL CHIP 100 5% 1/10W R510 1-216-845-11 METAL CHIP 100K 5% 1/10W
R401 1-216-841-11 METAL CHIP 47K 5% 1/10W R511 1-216-821-11 METAL CHIP 1K 5% 1/10W
R512 1-216-833-11 METAL CHIP 10K 5% 1/10W
R402 1-216-841-11 METAL CHIP 47K 5% 1/10W R516 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R403 1-216-833-11 METAL CHIP 10K 5% 1/10W R522 1-216-821-11 METAL CHIP 1K 5% 1/10W
R404 1-216-845-11 METAL CHIP 100K 5% 1/10W
R405 1-216-837-11 METAL CHIP 22K 5% 1/10W R523 1-216-821-11 METAL CHIP 1K 5% 1/10W
R406 1-216-821-11 METAL CHIP 1K 5% 1/10W R547 1-216-813-11 METAL CHIP 220 5% 1/10W
R550 1-216-837-11 METAL CHIP 22K 5% 1/10W
R410 1-216-833-11 METAL CHIP 10K 5% 1/10W R551 1-216-821-11 METAL CHIP 1K 5% 1/10W
R411 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R552 1-216-833-11 METAL CHIP 10K 5% 1/10W
R412 1-216-833-11 METAL CHIP 10K 5% 1/10W
R413 1-216-801-11 METAL CHIP 22 5% 1/10W R553 1-216-821-11 METAL CHIP 1K 5% 1/10W
R414 1-216-809-11 METAL CHIP 100 5% 1/10W R554 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R555 1-216-837-11 METAL CHIP 22K 5% 1/10W
R415 1-216-801-11 METAL CHIP 22 5% 1/10W R556 1-216-849-11 METAL CHIP 220K 5% 1/10W
R417 1-216-833-11 METAL CHIP 10K 5% 1/10W R557 1-216-805-11 METAL CHIP 47 5% 1/10W
R420 1-216-833-11 METAL CHIP 10K 5% 1/10W
R421 1-216-845-11 METAL CHIP 100K 5% 1/10W R558 1-216-837-11 METAL CHIP 22K 5% 1/10W
R422 1-216-845-11 METAL CHIP 100K 5% 1/10W R559 1-216-837-11 METAL CHIP 22K 5% 1/10W
R560 1-216-845-11 METAL CHIP 100K 5% 1/10W
R425 1-216-833-11 METAL CHIP 10K 5% 1/10W R561 1-216-821-11 METAL CHIP 1K 5% 1/10W
R427 1-216-833-11 METAL CHIP 10K 5% 1/10W R562 1-216-833-11 METAL CHIP 10K 5% 1/10W
R428 1-216-833-11 METAL CHIP 10K 5% 1/10W
R429 1-216-833-11 METAL CHIP 10K 5% 1/10W R563 1-216-809-11 METAL CHIP 100 5% 1/10W
R430 1-216-833-11 METAL CHIP 10K 5% 1/10W R566 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R431 1-216-845-11 METAL CHIP 100K 5% 1/10W < VIBRATOR >

R432 1-216-845-11 METAL CHIP 100K 5% 1/10W
R433 1-216-845-11 METAL CHIP 100K 5% 1/10W X301 1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
R434 1-216-845-11 METAL CHIP 100K 5% 1/10W X302 1-795-482-11 VIBRATOR, CERAMIC (16MHz)
R435 1-216-817-11 METAL CHIP 470 5% 1/10W

7
HCD-CPZ1DAB

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.0 2006.08 New
1.1 2006.10 Change of Part for R625 on the TC board
Change of DAB, SP, SUB POWER boards (Suffix-13)
Addition of Part No. for CORD (WITH CONNECTOR)
Change of MAIN board (Suffix-13) (Suppliment-1)
(ECN-ECB84739/ECB87597/ECB88125)