HCD-V818

SERVICE MANUAL E Model

HCD-V818 is the tuner, deck, Video CD

and amplifier section in MHC-V818.

Model Name Using Similar Mechanism HCD-V800

CD CD Mechanism Type CDM38L-5BD24AL
SECTION Base Unit Type BU-5BD24AL
Optical Pick-up Type KSS-213D/Q-NP
Model Name Using Similar Mechanism HCD-GRX8/R800/RX88/RX99
TAPE
DECK Tape Transport Mechanism Type TCM-230AWR1
SECTION
TCM-230PWR1

SPECIFICATIONS

— Continued on next page —

COMPACT DISC DECK RECEIVER

MICROFILM

–1–
Downloaded from www.Manualslib.com manuals search engine
 SELF DIAGNOSIS
This unit is equipped with a self-diagnosis function.
The function is used for diagnosing the conditions of the circuits of the VIDEO board.
The circuits can be determined if normal or abnormal by the lighting of D502 of the VIDEO board.

Lighting of D502
When lit : Operates normally
Blinks repeatedly : The circuit may be faulty.

[VIDEO BOARD] (SIDE A)

D502
SL501 SL502 SL503
TEST MODE

IC505

CT503
VIDEO IC507
FREQUENCY

–2–
Downloaded from www.Manualslib.com manuals search engine
 MODEL IDENTIFICATION
CAUTION — BACK PANEL —
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.

Notes on chip component replacement

• Never reuse a disconnected chip component.
Parts No.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.

Laser component in this product is capable of emitting radiation

exceeding the limit for Class 1. • Abbreviation
EA : Saudi arabia model
HK : Hong Kong model
This appliance is classified as SP : Singapore model
a CLASS 1 LASER product. MY : Malaysia model
The CLASS 1 LASER PROD- TW : Taiwan model
UCT MARKING is located on IA : Indonesian model.
the rear exterior.
PARTS No. MODEL
4-999-907-0π SP, MY
The following
4-999-907-1π EA
caution label is
4-999-907-3π HK
located inside of
4-999-907-4π TW
the unit.
4-999-907-5π IA

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on

SAFETY-RELATED COMPONENT WARNING !! the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE
serve from more than 30 cm away from the objective lens.
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN
LASER DIODE AND FOCUS SEARCH OPERATION
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. CHECK
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS Carry out the “S curve check” in “CD section adjustment” and check
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. that the S curve waveform is output two times.

–3–
Downloaded from www.Manualslib.com manuals search engine
 TABLE OF CONTENTS

1. SERVICING NOTE .......................................................... 5 9. EXPLODED VIEWS

9-1. Case Section ........................................................................ 99
2. GENERAL .......................................................................... 6 9-2. Chassis Section ................................................................. 100
9-3. Front Panel Section ........................................................... 101
3. DISASSEMBLY 9-4. CD Mechanism Deck Section-1 (CDM38L-5BD24AL) .. 102
9-5. CD Mechanism Deck Section-2 (CDM38L-5BD24AL) .. 103
3-1. Loading Panel ....................................................................... 9
9-6. Base Unit Section (BU-5BD24AL) .................................. 104
3-2. Front Panel ........................................................................... 9
9-7. TC Mechanism Section 1
3-3. Cassette Mechanism Deck .................................................. 10
(TCM230AWR1, TCM230PWR1) ................................... 105
3-4. Panel Board and Cont Com Board ...................................... 10
9-8. TC Mechanism Section 2
3-5. Disc Tray ........................................................................... 11
(TCM230AWR1, TCM230PWR1) ................................... 106
4. TEST MODE .................................................................... 12
10. ELECTRICAL PARTS LIST .................................. 107
5. SERVICE MODE ............................................................ 14

6. MECHANICAL ADJUSTMENTS .......................... 16

7. ELECTRICAL ADJUSTMENTS ............................... 16

8. DIAGRAMS
8-1. Circuit Boards Location ...................................................... 22
8-2. Block Diagrams
• CD Section ....................................................................... 23
• Video Section ................................................................... 25
• Deck Section .................................................................... 27
• Main Section .................................................................... 29
• Power Section .................................................................. 31
• Display Section ................................................................ 33
• Section ............................................................... 35
8-3. Printed Wiring Board – CD Section – ................................. 37
8-4. Schematic Diagram – CD Section – ................................... 39
8-5. Schematic Diagram – Deck Section – ................................ 41
8-6. Printed Wiring Board – Deck Section – .............................. 43
8-7. Printed Wiring Board – Video Section – ............................. 45
8-8. Schematic Diagram – Videon (1/3) Section – ..................... 47
8-9. Schematic Diagram – Videon (2/3) Section – ..................... 49
8-10. Schematic Diagram – Videon (3/3) Section – .................. 51
8-11. Printed Wiring Board – Main Section – ........................... 53
8-12. Schematic Diagram – Main (1/4) Section – ..................... 55
8-13. Schematic Diagram – Main (2/4) Section – ..................... 57
8-14. Schematic Diagram – Main (3/4) Section – ..................... 59
8-15. Schematic Diagram – Main (4/4) Section – ..................... 61
8-16. Printed Wiring Board – Mic/HP Section – ....................... 63
8-17. Schematic Diagram – Mic/HP Section – .......................... 64
8-18. Printed Wiring Board – Power Amp Section – ................. 65
8-19. Schematic Diagram – Power Amp Section – ................... 67
8-20. Schematic Diagram – Transformer Section – ................... 69
8-21. Printed Wiring Board – Transformer Section – ................ 71
8-22. Printed Wiring Board – Leaf SW Section – ..................... 72
8-23. Schematic Diagram – Leaf SW Section – ........................ 72
8-24. Printed Wiring Board – Display Section – ....................... 73
8-25. Schematic Diagram – Display Section – .......................... 75
8-26. Schematic Diagram – Panel Section – ............................. 77
8-27. Printed Wiring Board – Panel Section – ........................... 79
8-28. Schematic Diagram – CD Motor Section – ...................... 81
8-29. Printed Wiring Board – CD Motor Section – ................... 83
8-30. IC Block Diagrams ........................................................... 85
8-31. IC Pin Functions ............................................................... 87

–4–
Downloaded from www.Manualslib.com manuals search engine
 SECTION 1
SERVICING NOTE
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF

1 Remove the case.

3 pull-out the disc tray.

2 Turn the cam to the

direction of arrow.

Note for Installation (ROTARY ENCODER)

Note:When attaching the Base unit, Insert the

BU cam section A into the groove of BU cam.

Section A
Groove

Note:When attaching the BU cam,

engage the Rotary encoder
switch as shown in the figure.

–5–
Downloaded from www.Manualslib.com manuals search engine
 SECTION 2
GENERAL
Front Panel

1 2 3 4 5 6

8
9
10
65
11

12
64
13
63
62
61
14 15 16 17 18 19 20
60
21 22 23
59 24 25 26 27 28
29

58 57 56 30
55 31
32
54
33

50 49 48 47 46 45 39 38 37 36 35 34
53 52 51
44 43 42 41 40

–6–
Downloaded from www.Manualslib.com manuals search engine
 LOCATION OF PARTS AND CONTROLS

1 1/u (POWER) button 34 VOLUME, +, – knob

2 DISC 1 button and indicator 35 GROOVE button and indicator
3 DISC 2 button and indicator 36 DBFB button
4 DISC 3 button and indicator 37 ), + button and indicator
5 DISC SKIP/EX-CHANGE button 38 ENTER/NEXT button and indicator
6 § (EJECT) button 39 JOG dial
7 Disc tray 40 p button
8 VIDEO CD indicator 41 P FILE MEMORY button
9 PBC indicator 42 GEQ CONTROL button
10 PCB OFF indicator 43 FILE SELECT button
11 PLAY MODE/DOLBY NR TUNER MEMORY button 44 FILE button and indicator
12 EDIT/DIRECTION button 45 AUTO BPM button and indicator
13 REPEAT/STEREO/MONO button 46 0, – button and indicator
14 FUNCTION button 47 JAM button and indicator
15 TAPE A 9 button and indicator 48 SPEED button
16 TAPE A ( button and indicator 49 SELECT button
17 TAPE B 9 button and indicator 50 ON/OFF button and indicator
18 TAPE B ( button and indicator 51 BEAT LEVEL button
19 CD ^ button and indicator 52 PAD B button
20 TUNER/BAND button 53 PAD A button
21 KARAOKE PON/MPX button 54 MIC 2 jack
22 SURROUND button 55 MIC 1 jack
23 SONIC FORMATION button and indicator 56 CD NON-STOP button and indicator
24 ACTIVE button 57 CD FLASH button
25 SELECT button 58 CD LOOP button
26 RETURN button 59 MIC LEVEL knob
27 PREV button 60 ECHO LEVEL knob
28 NEXT button 61 DEMO button
29 r REC button and indicator 62 DISPLAY button
30 P PAUSE button and indicator 63 TIMER/SELECT button
31 HI-DUB button 64 CLOCK/TIMER SET button
32 CD SYNC button 65 Display window
33 PHONES jack

–7–
Downloaded from www.Manualslib.com manuals search engine
 This section is extracted from
instruction manual.

–8–
Downloaded from www.Manualslib.com manuals search engine
 SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.

3-1. LOADING PANEL

3 Loading panel

Claws

1 Turn the cam to the direction

of arrow.
2 Pull-out the disc tray.

3-2. FRONT PANEL

6 Flat type wire

7 Flat type wire (CN107)
(CN106)

8 Flat type wire

(CN101)
3 Screw
(BVTP3x10) 4 Connector
(CN203)

2 Screw
(BVTP3x10)

5 Connector
9 Front panel assembly (CN752)

1 Three screws
(BVTP3x8)

–9–
Downloaded from www.Manualslib.com manuals search engine
 3-3. CASSETTE MECHANISM DECK
9 Three screws
(BVTP 2.6x8)
!∞ Mechanism deck
!º Two screws
(BVTP 2.6x8)
6 Remove the cassette lids. 2 Two screws
(BVTT 2x4) !£ Two screws
(BVTP 2.6x8)

4 Damper, oil

3 Damper, oil

1 Two screws
(BVTT 2x4)

7 Spring !¢ Bracket !¡ Screw

!™ Screw (BVTP 2.6x8)
(BVTP 2.6x8)

5 Push the cassette lids.

8 Spring

3-4. PANEL BOARD AND CONT COM BOARD

1 Ten screws
4 Shield (BVTP 2.6x8)

2 Three screws
(BVTP 2.6x8)

7 Nut

6 Konb(Jog)
!™ CONT COM board 5 Flat type wire
3 Panel board
(CN602)

8 Konb(Volume)
9 Nut

!º Four screws
(BVTP 2.6x8)

!¡ Six screws
(BVTP 2.6x8)

– 10 –
Downloaded from www.Manualslib.com manuals search engine
 3-5. DISC TRAY
(Perfom after removing the front panel.) Note: When installing the Disc tray, pull around the flat type wire to
pass through the clawA and clawB, as shown in the figure.

3 Flat type wire (8 core)

4 Two claws

2 Pull-out the disc tray.

5 Remove the disc tray.
ClawB
ClawA

1 Turn the cam the

direction of arrow.

– 11 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 4
TEST MODE
VIDEO CD COLOR-BARS MODE

On this mode, the data of the color-bars signal as a picture signal and the 1kHz sine wave signal as a sound signal are output by the
mechanism control microcomputer (IC502) for video CD signal check. When measurement of the voltage and waveform on the VIDEO
board, perform it in this mode.
For refernce, the color-bars signal can be observed at J302 (VIDEO OUT) and the sound signal can be observed at J101 (VIDEO/MD
(AUDIO) OUT) using an oscilloscope.
1. Connect the lead wire to both ends of the land of SL503 of the VIDEO board.
2. Turn the power on. Press FUNCTION button to select CD.
3. After 2 or 3 seconds later, connect the lead wire.
4. After measuring, remove the lead wire connected.
[VIDEO BOARD] (SIDE A)

D502
SL501 SL502 SL503
TEST MODE

IC505

CT503
VIDEO IC507
FREQUENCY

[VIDEO BOARD] (SIDE B)

SL503 IC502
TEST
SL502
MODE SL501

– 12 –
Downloaded from www.Manualslib.com manuals search engine
 IC502 OF VIDEO BOARD

IC502 of the VIDEO board consists of the former type and new type. The following table shows the differences between the two types.
Only spare parts for the new type IC502 are supplied.
Units using the former IC502 will not function when replaced with the new type without performing the following procedure.
Consequently, replace IC502 of units using the former type according to the following procedure.

Table of Differences
FORMER TYPE NEW TYPE
C407, 408 MOUNT NO MOUNT
IC502 M306200MC-302FP M306200MC-305FP
JW421, JW422 NO MOUNT MOUNT
IC402 MOUNT NO MOUNT
R413, 421, 422 MOUNT NO MOUNT
X401 MOUNT NO MOUNT

Replacing Procedure
1. Remove IC402.
2. Solder JW421 and JW422, or short-circuit with a lead wire, etc.
3. Replace IC502 with a new one.

How to Differentiate [VIDEO Board] (SIDE A)

Those with IC402: FORMER TYPE

Those without: NEW TYPE
IC505

– 13 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 5
SERVICE MODE
MC Cold Reset
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the
customer.
Procedure:
1. Press three buttons p , ENTER/NEXT , and 1/u simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

CD Delivery Mode
• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press 1/u button to turn the set ON.
2. Press CD LOOP button and 1/u button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.

MC Hot Reset
• This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions same as if the power cord is plugged
in and out.
Procedure:
1. Press three buttons p , ENTER/NEXT , and DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

Sled Servo Mode

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons p , ENTER/NEXT , and § simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4. With the CD in stop status, press ) + utton move the pick-up to outside track, or – 0 button to inside track.
5. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.

Change-over of AM Tuner Step between 9kHz and 10kHz

• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “AM”.
3. Press 1/u button to turn the set OFF.
4. Press ENTER/NEXT and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “AM 9k STEP” or “AM
10k STEP”, and thus the channel step is changed over.

LED and Fluorescent Indicator Tube All Lit, Key Check Mode
Procedure:
1. Press three buttons p , ENTER/NEXT , and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays “K 1 V0 J0”. Each time a button is pressed, “K”value increases. However,
once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating JOG dial in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.

Aging Mode
This mode can be used for checking the operations of the CD player and tape deck.
• When problems occur;
Aging stops. If currently aging the tape deck, the state when aging stops will be displayed on the fluorescent indicator tube.
• When no problems;
Aging continues.

Preparations:
• Set the CD on the DISC1 tray.
• Insert a commercially available tape for recording (tapes which contents can be erased, etc.) in decks A and B.

– 14 –
Downloaded from www.Manualslib.com manuals search engine
 Setting the aging mode:
Press the p button, ENTER/NEXT button, and DISC SKIP/EX-CHANGE button together.
When the aging mode is set, the CD roulette mark blinks. To exit the mode, press the 1/u button and turn OFF the power.

Sequence:
The aging mode is executed in the following sequence.
If the function is set to “CD” when the aging mode is set, aging is performed starting from the CD player. When set to “TAPE A” or “TAPE
B”, aging is started from deck A.
If the function is set to others, aging will not be started until the function is switched to CD or TAPE.

Aging of CD player (12 minutes)

Aging of deck A
Maximum about 12 minutes
Aging of deck B

Display of status:
• The aging status is displayed on the fluorescent display tube. (Only when executing the tape deck section.)
• During the aging of the tape deck, the operations performed will be displayed. If operations ended abnormally, this will be displayed at the
fluorescent indicator tube.

Tape Deck
Display of Operations Operation Timing of Ending
TAPE A AG-1 TAPE A REW Shutoff
TAPE A AG-2 TAPE A FWD 2 minute playback
TAPE A AG-3 TAPE A FF 20 seconds or shutoff
TAPE A AG-4 TAPE A REV 2 minutes playback
TAPE A AG-5 TAPE A REW Shutoff
TAPE B AG-1 TAPE B REW Shutoff
TAPE B AG-2 TAPE B FWD 2 minute playback
TAPE B AG-3 TAPE B FF 20 seconds or shutoff
TAPE B AG-4 TAPE B REV 2 minute playback
TAPE B AG-5 TAPE B REW Shutoff

Operations during aging

• Operations are performed in the following sequence during aging

<CD player>
1. The CD tray rotates and disc 1 is selected.
2. Chucking is performed.
3. TOC is read.
4. Track 1 played back for 8 seconds.
5. The CD tray opens and closes again.
6. 1 to 5 is repeated.
7. After 12 minutes of aging, aging is switched to the tape deck.

<Tape Deck>
1. The tape in deck A is rewound to the head.
2. The FWD side is played back for 2 minutes.
3. The tape is fast forwarded (FF) for 20 seconds. The following procedure is performed when the tape end is reached before the 20 seconds.
4. The REV side is played back for 2 minutes.
5. The tape is rewound to the head (REW).
6. The tape in deck B is rewound to the head.
7. The FWD side is played back for 2 minutes.
8. The tape is fast forwarded (FF) for 20 seconds. The following procedure is performed when the tape end is reached before the 20 seconds.
9. The REV side is played back for 2 minutes.
10. The tape is rewound to the head (REW).
11. Aging is switched to the CD player.

– 15 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 6 SECTION 7
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution DECK SECTION 0 dB=0.775V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head damagnetizer.
record/playback heads pinch rollers 2. Do not use a magnetized screwdriver for the adjustments.
erase head rubber belts 3. After the adjustments, apply suitable locking compound to the
capstan idlers parts adjusted.
2. Demagnetize the record/playback head with a head demagne- 4. The adjustments should be performed with the rated power sup-
tizer. ply voltage unless otherwise noted.
3. Do not use a magnetized screwdriver for the adjustments. 5. The adjustments should be performed in the order given in this
4. After the adjustments, apply suitable locking compound to the service manual. (As a general rule, playback circuit adjustment
parts adjusted. should be completed before performing recording circuit adjust-
5. The adjustments should be performed with the rated power sup- ment.)
ply voltage unless otherwise noted. 6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise
Torque Measurement specified.
Mode Torque meter Meter reading
31 to 71 g • cm Tape Signal Used for
FWD CQ-102C (0.43 – 0.98 oz • inch) P-4-A100 10 kHz, –10 dB Azimuth Adjustment
FWD 2 to 6 g • cm
CQ-102C WS-48B 3 kHz, 0 dB Tape Speed Adjustment
back tension (0.02 – 0.08 oz • inch)
31 to 71 g • cm P-4-L300 315 Hz, 0 dB Level Adjustment
REV CQ-102RC
(0.43 – 0.98 oz • inch)
REV 2 to 6 g • cm
CQ-102RC Record/Playback Head Azimuth Adjustment
back tension (0.02 – 0.08 oz • inch)
71 to 143 g • cm (Deck A, Deck B)
FF/REW CQ-201B
(0.98 – 1.99 oz • inch)
100 g or more Note: Perform this adjustments for both decks.
FWD tension CQ-403A
(3.53 oz or more)
100 g or more Procedure:
REV tension CQ-403R
(3.53 oz or more) 1. Mode : Playback
test tape
P-4-A100 main board
(10kHz, –10dB) CN301
Pin 1 (L-CH) level meter
Pin 3 (R-CH)

set +
–
main board
CN301
Pin 2 (GND)

2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.

L-CH
output
peak within
level
1 dB within 1dB

R-CH
peak
screw
position
screw
L-CH R-CH position
peak peak

– 16 –
Downloaded from www.Manualslib.com manuals search engine
 3. Mode: Playback Tape Speed Adjustment (Deck A)
test tape
P-4-A100 main board Note: Set the test mode using the following method and begin tape
(10kHz, –10dB) CN301 speed adjustment.
Pin 1 (L-CH) oscilloscope In the test mode, the speed will switch to double speed or
Pin 2 (GND) normal speed each time the HI-DUB button is pressed.
L

set
Procedure:
With the power turned ON, press the p button, ENTER/NEXT
R
button, and DISC 3 button simultaneously.
(The “VOLUME” on the fluorescent display tube will blink while
Pin 3 (R-CH) in the test mode.)
To exit the test mode, press the 1/u button.

Waveform of oscilloscope 1. Insert the WS-48B into deck B.

2. Press the · button of deck B.
3. Press the HI-DUB button and play the tape at double speed.
4. Adjust RV1001 of the LEAF SW board so that the reading of
in phase 45° 90° 135° 180°
the frequency counter becomes 6000 ± 180 Hz.
good wrong 5. Press the HI-DUB button and play the tape at normal speed.
6. Adjust RV1002 of the LEAF SW board so that the reading of
4. After the adjustments, apply suitable locking compound to the the frequency counter becomes 3000 ± 90 Hz.
parts adjusted.
Adjustment Location: LEAF SW board
Adjustment Location: Playback Head (Deck A)
Record/Playback/Erase Head (Deck B) Sample Value of Wow and flutter
± 0.15% W.Peak (IEC)
1 Remove the four claws 0.1% W.RMS (NAB)
± 0.2% W.Peak (DIN)

Playback Level Adjustment (Deck A, Deck B)

Procedure:
Mode: Playback
2 Window
test tape
P-4-L300 level meter
(315Hz, 0dB)

set

main board
CN301
Pin 1 (L-CH)
Pin 3 (R-CH)
Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.

Adjustment level:
Reverse Foward
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board

Adjustment Location
[LEAF SW BOARD]

RV1001(High Speed)
RV1002(Normal Speed)

RV1002 RV1001

– 17 –
Downloaded from www.Manualslib.com manuals search engine
 Record Bias Adjustment (Deck B) Record Level Adjustment (Deck B)

Procedure: Procedure:

INTRODUCTION INTRODUCTION
When set to the test mode performed in Tape Speed Adjust- When set to the test mode performed in Tape Speed Adjust-
ment, when the tape is rewound after recording, the “REC memory ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is mode” which rewinds only the recorded portion and playback is
set. set.
This “REC memory mode” is convenient for performing this ad- This “REC memory mode” is convenient for performing this
justment. During recording, the input signal FUNCTION will auto- adjustment. During recording, the input signal FUNCTION will au-
matically switch to VIDEO. tomatically switch to VIDEO.
(After recording, press the – 0 button without stopping will (After recording, press the – 0 button without stopping will
return to the position where recording was started.) return to the position where recording was started.)

1. Press FUNCTION button to select VIDEO. (This step is not 1. Press FUNCTION button to select VIDEO. (This step is not
necessary if the above test mode has already been set.) necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then 2. Insert a tape into deck B, press the r REC button, and then
press the ( button to start recording. press the ( button to start recording.
3. Mode: Record 3. Mode: Record
VIDEO (AUDIO) IN VIDEO (AUDIO) IN
1) 315 Hz 315Hz 50 mV (–23.8 dB)
} 50 mV (–23.8 dB)
2) 10 kHz
AF OSC AF OSC
blank tape blank tape
600 Ω CS-123 600 Ω CS-123
attenuator attenuator

set set

4. Mode: Playback 4. Mode: Playback

recorded level meter recorded level meter
position position

set set

main board main board

CN301 CN301
Pin 1 (L-CH) Pin 1 (L-CH)
Pin 3 (R-CH) Pin 3 (R-CH)

5. Confirm playback the signal recorded in step 2 become adjust- 5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows. ment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH) If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4. and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.

Adjustment level: The playback output of 10 kHz level difference Adjustment level:
against 315 Hz reference should be ± 1.0 dB. CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)

Adjustment Location: AUDIO board Adjustment Location: MAIN board

Adjustment Location: [MAIN BOARD] (Conductor Side)

RV301
[AUDIO BOARD] (Conductor Side) Record Level (Lch)

RV341(Lch),RV441(Rch) RV311(Lch),RV411(Rch)
Record Bias Playback Level (Deck A)
1 3
CN301
IC301
RV301 RV401
RV411
RV441 RV341 RV311 RV351
Record Level (Rch)

RV301(Lch),RV401(Rch)
Playback Level (Deck B)

– 18 –
Downloaded from www.Manualslib.com manuals search engine
 CD SECTION Note : A clear RF signal waveform means that the shape “◊” can
be clearly distinguished at the center of the waveform.
NOTE :
RF signal waveform
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given. VOLT/DIV : 200mV
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TIME/DIV : 500ns
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when
the signal level is low than specified value with the following level : 1.3 +0.25 Vp-p
–0.20
checks.

S Curve Check

oscilloscope E-F Balance (Traverse) Check (Without remote comander)

BD board
oscilloscope
BD board
TP (FE) +
TP (VC) –
TP (TE) +
TP (VC) –
Procedure :
1. Connect oscilloscope to test point TP (FE) on BD board.
2. Connect between test point TP (FEI) and TP (VC) by lead wire. Procedure :
3. Turned Power switch on. 1. Short-circuit SL502 of the video board to GND.
4. Put disc (YEDS-18) in and turned Power switch on again and 2. Connect oscilloscpe to test point TP (TE) on BD board.
actuate the focus search. (actuate the focus search when disc 3. Turned Power switch on. Press FUNCTION button to select
table is moving in and out.) CD.
5. Check the oscilloscope waveform (S-curve) is symmetrical be- 4. Set a disc (YEDS-18) and play.
tween A and B. 5. Press the PLAY MODE button.
And confirm peak to peak level within 3±1 Vp-p. (The sledding servo is turned OFF.)
6. Check the level B of the oscilliscope’s waveform and the A (DC
S-curve waveform voltage) of the center of the Traverse waveform.
Confirm the following :
symmetry
A/B x 100 = less than ± 7%

Traverse waveform
A
Within 3 ± 1 Vp-p Center of the waveform

B
B

A (DC voltage)
6. After check, remove the lead wire connected in step 2. 0V
Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
level : 500 mV ± 100 mVp-p
• Take sweep time as long as possible and light up the bright-
ness to obtain best waveform.
7. Press the PLAY MODE button. (The tracking servo and sledding
RF Level Check servo are turned ON.) Confirm the C (DC voltage) is almost
equal to the A (DC voltage) is step 6.
oscilloscope
BD board Traverse waveform

TP (RF) +
TP (VC) –
C (DC
0V voltage)
Procedure :
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on. Sled servo Sled servo
3. Put disc (YEDS-18) in to play the number five track. OFF ON
4. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.

– 19 –
Downloaded from www.Manualslib.com manuals search engine
 E-F Balance (Traverse) Check (With remote commander) 7. Press the PLAY MODE button. (The tracking servo and sled-
ding servo are turned ON.) Confirm the C (DC voltage) is almost
oscilloscope equal to the A (DC voltage) is step 7.
BD board
Traverse waveform
TP (TE) +
TP (VC) –

Procedure : C (DC
0V voltage)
1. Connect oscilloscpe to test point TP (TE) on BD board.
2. Short-circuit SL502 of the video board to GND.
3. Turned Power switch on. Press FUNCTION button to select Tracking servo Tracking servo
CD. Sled servo Sled servo
4. Put disc (YEDS-18) in to play the number five track. OFF ON
5. Press the PLAY MODE button. (The tracking servo and the
sledding servo are turned OFF.) 8. Desolder the short-land (SL502) short-circuited at step 2.
6. Check the level B of the oscilliscope's waveform and the A (DC
voltage) of the center of the Traverse waveform.
Confirm the following :
A/B x 100 = less than ± 22%

Traverse waveform
Center of the waveform

0V A (DC voltage)

level : 1.3 ± 0.6 Vp-p

Adjustment Location :

[ BD BOARD ] – SIDE A –

TP TP
(RF) (VC)

TP
(FE) TP
(FEI)
TP
(TE)

– 20 –
Downloaded from www.Manualslib.com manuals search engine
 VIDEO SECTION

Frequency adjustment
frequency counter

1. Connect the frequency counter to check point of the VIDEO

board. VIDEO board
+
(DCLK)
2. Adjust CT503 of the VIDEO board so that the frequency counter –
read 27MHz ± 80Hz at STOP condition.

Adjustment Location :

[ VIDEO BOARD ] – SIDE A –

D502
SL501 SL502 SL503
TEST MODE

IC505

(27MHz)

CT503
VIDEO IC507
FREQUENCY

(GND)

[ VIDEO BOARD ] – SIDE B –

(27MHz)
IC506

(GND)

SL503 IC502
TEST
SL502
MODE SL501

– 21 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 8
DIAGRAMS
8-1. CIRCUIT BOARDS LOCATION

TRANSFORMER board

LEAF SW board
VIDEO board

AUDIO board

MAIN board

CONT (COM) board CD-SW board

POWER board DECO board

TUNER(FM/AM)

MIC board

PANEL board
HP board

MOTOR (TURN) board

CONNECTOR board

BD board

SENSOR board

MOTOR (SLIDE) board

– 22 –
Downloaded from www.Manualslib.com manuals search engine
 HCD-V818

8-2. BLOCK DIAGRAMS

– CD SECTION –

IC391
OPTICAL PICK-UP BLOCK CD DIGITAL
(KSS-213D/Q-NP) IC101 MD2 OUT
DIGITAL SERVO 70 +5V OPTICAL
DETECTOR IC103 DIGITAL SIGNAL PRCESSOR
VCC RF AMP DIGITAL D OUT
E ADDRESS 32K ERROR 71 1 DOUT
OUT
VC GENERATOR RAM CORRECTOR

DATA BUS
A A
3
C C RF RF RF AC SERIAL/ DATA
A C 5 RF EQ EFM D/A DATA
D D SUMMING 3 36 MUX REGISTER PARALLEL 46 ADATA
B D 6 AMP AMP DEMODULATOR PROCESSOR PROCESSOR
B B
4 BCLK 47 BCLK
ASYMMETRY DIGITAL PEAK LCLK 45 LCLK
F
CORRECTION PLL DETECTOR
FOCUS FE
INTEG- ASYI
ERROR 15 38 SUBQ
RATOR 77 SUBQ
AMP SUBCODE Q
ASYO PROCESSOR SQCK
78 SQCK
39 MUTE
79 AMUTE

E E TE SYNC TIMING SCOR

9 TRACKING 74 SCOR
F F ERROR 13 PROTECTOR GENERATOR 1
8 AMP
SCLK 83 SCLK
18-TIMES
NOISE CLV SERVO TIMING
11 OVERSAMPLING
LD LD SHAPER PROCESSOR GENERATOR 2
FILTER
DRIVE 1
Q101
10 IC104
CLOCK XTAI
LD 62 MCK
GENERATOR
VC CONTROL SIGNAL
LASER 12
DIODE BUFFER BLOCK XTSL
PD VC
VC 30
SERVO
BLOCK
SENS
64
80 SENS
A
PD LD ON VIDEO
2 APC LD 19 RFDC SECTION
AMP 26 DATA (Page 25)
LD FE FOK 86 DATA
29 SERVO
POWER REF CPU XLT
TE A/D MIRR AUTO 87 XLT
17 27 INTERFACE
CONVERTER DETECTOR SEQUENCER CLK
DFCT 88 CLK
IC102
FOCUS/TRACKING COIL DRIVE INTEG- SE
28
SPINDLE/SLED MOTOR DRIVE RATOR
C2PO 56 C2PO
T+ SERVO
1
TRACKING SWITCH INTERFACE
COIL TFDR S STOP 99 +5V
T 4 Q102,103 PWM
2 S101
TRDR GENERATOR SERVO DSP
5 LIMIT SW
CTRL 1

CTRL 2

TFDR
F+ 4 TRACKING
TRACKING
16 TRDR PWM
6 GENERATOR SERVO
FOCUS
FFDR CTRL 1
COIL F 19
17 FRDR FFDR CTRL 2
20 8 FOCUS
FOCUS XRST
FRDR PWM XRST 81
SD+ 10 GENERATOR SERVO
13 LD ON
M102
SLED M SRDR SRDR
SD 10 2 SLED
MOTOR SLED
12 SFDR SFDR PWM
9 100 GENERATOR SERVO
SP+
M101 27 • SIGNAL PATH
SPINDLE M MDP : CD
MOTOR SP 24 96
26 : Digital out
23 VC
: VIDEO

MUTE 15
TURN
MOTOR DRIVER TABLE
IC701 SENSOR T. SENS
IC702

M701 IN1 3 DISC

TURN 7 OUT1
M SENSOR DISC SENS
MOTOR 2 OUT2 IN2 6 IC703 Q701

ROTARY ENC 1
SLIDE
MOTOR DRIVER
IC801
S801
OPEN/CLOSE
ENCODER
S811
ENC 2
ENC 3 C
OPEN MAIN
M801 DET SECTION
4 OUT2 RIN 2 TBL.L
SLIDE
MOTOR
M
7 OUT1 FIN 10 TBL.R (Page 29)
09 LOAD IN
LOAD OUT

– 23 – – 24 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

– VIDEO SECTION – * Note

D-RAM ROM
When replacing IC502, refer to “IC502 of
IC507 IC506 video Board” in “Service Note” (page 13).
UCAS

DQ16
LCAS
RAS

DQ1

A11

A17

A10
WE

O0

O7
A0

A8

A0

CE
13 14 28 29 16 - 19 22 - 26 2 - 10 31 - 39 13 - 15 17 - 21 25 4 28 29 3 2 14 10 12 - 5 27 26 23 22

38 42 40 10 - 29 58 - 44 37
MWE
RASO

CAS

MD0

MD15

MA0

MA10

MCE
I

I
INVERTER
OUTPUT AMP
IC501
IC401

BUFFER TRAP J302

ADATA 1 4 4 CD-DATA Y-OUT 69 MIX AMP MUTE
Q301 Q302,306,307 5 7 VIDEO OUT
BCLK 13 10 3 CD-BCK Q308,310 Q454
LRCK 5 8 5 CD-LRCK
J301
MUTE S VIDEO
3 1
Q453 4 3 OUT
C2P0 6 CD-C2P0
VIDEO/CD DECODER 2 1
IC505
DATAI
112 HD-OUT
DATAO
119 HD-IN
CLK1 BUFFER
117 HCK C-OUT 75
HRDY Q303,304
113 HRDY
INT
114 HINT
HSEL DA-DATA 110
121 HSEL
RST DA-LRCK 108
60 RESET
DA-BCK 111
INVERTER 93 PGIO2/VSYNC/CSYNC VCK-IN 106
Q502
DA-XCLK 86 DIGITAL FILTER & D/A CONVERTER
IC509
AMP
IC101

18 14 L - CH
D/A 3 1
19 PLM
CONV
17 11 R-CH

DATA0
9
CLK1 CLOCK 1

A MECHA CONTROL
IC502
8
7
MODE
DIVIDER
24
X503
27MHz
CT503
CD VIDEO
10 21 20 4
SECTION
FREQUENCY
(Page 24)
DATA0
31 DATA1O
DATAI SHARPNESS 34
CLK1
INT
32
33
20
DATA1I
CLK1
CL680 INT
DF LATCH
A7
22
65 INVERTER
G
HSEL IC504 MAIN
21 CL680 HSEL
HRDY XIN 15 SECTION
23 CL680 HRDY X501
RESET 27MHz (Page 30)
24 680 RESET 10MHz 3 6
XOUT 13 384FS
NTSC 11 8
NT/PAL
SYSTEM 1 12 768FS
45 BUS 93 SELECT
+5V AUTO
DATA 3 DSP DATA S501
XLT 4 DSP LATCH PAL
TEST LED 73 D502
CLK 5 DSP CLK
SENS 1 SENSE IIC DATA
SCLK 2 SENSE CLK IIC CLK
AMUTE 10 DSP MUTE XRESET 12 XRST
INTERFACE
CTRL1 11 CTRL1(L:DOUBLE)
NEW IC402
CTRL2 27 CTRL2 TYPE
LDON 28 LDON (*NOTE) • R CH: Same as L ch
SCOR 18 SCOR 14 I2C.DATA • SIGNAL PATH
SUBQ 36 SUBQ DATA 13 I2C.CLK RESET 18
XIN 19
: CD
SQCK 37 SUBQ CLK DSENS 19 9 I to U X401
77 DEVICE RESET U to I 72 10 U to I 8MHz
: CHROMA
XOUT 20
I2C.CLK 29 11 TXD :Y
I2C.DATA 30 12 RXD
: VIDEO
FORMER TYPE
(*NOTE)
XRST
09 MCK

– 25 – – 26 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

– DECK SECTION –

PB A/B
S1004 S1008
A CrO2 B CrO2 MS OUT

CN301
3 R CH
RV311
16 17 19 28 27 26
PLAYBACK 1
IC611 PB-A/B A 120/70 B 120/70
LEVEL MS
DECK A
L 70
A IN PAS
48 PB OUT
HP101 B IN 40 PB L
46 120
PB HEAD R CH DOL LM ON/ 25
(DECK A) R LM ON/OFF
DOLBY NR OFF
DOLBY NR
NORM/
RV301 IC301
HIGH 18 NORM/HIGH
PLAYBACK NR ON/
IC601 NR ON/OFF
LEVEL OFF 23
DECK B
L 24 REC/PB/PASS
RV301
PB
REC/PB HEAD REC LEVEL
(DECK B) RECOUT DOLBY
39 RIN
R R CH TYPE B 44 REC L

EQOUT EQIN BIAS ON/OFF

36 38 BIAS SW 20 BIAS ON/OFF
RM ON/OFF 22 RM ON/OFF
ALC ON/OFF 15 ALC ON/OFF
M

1
C

3
IC602 32 33
P R
4 RELAY REC/PB
HRPE101 REC/PB CAPM CNT1M
CAP MOTOR
RV341 CONTROL CAPM CNT2M
REC Q336-343
BIAS +7.5V CAPM CNT1P
Q623 CAPM CNT2P
M1 SPEED
SWITCH
CAPSTAN M CONTROL CAP M H / L
Q335
MOTOR

ERASE BIAS
REC BIAS
BIAS OSC
T621, Q621, 622
Q1001
B
ERASE HEAD X MAIN
SECTION
RV1002 RV1001
REEL (Page 29)
NORMAL HIGH
DETECT A SHUT
SPEED SPEED
IC1001

REEL
DETECT B SHUT
IC1002

S1001 (A PLAY)
• R CH : Same as L ch +5V A PLAY
• SIGNAL PATH S1002 (B PLAY)
B PLAY
: PB (DECK A)
: PB (DECK B) S1003
(A HALF) +5V
: REC (DECK B)
+5V

S1005
(REC A)
09 S1006 B HALF
(B HALF)

S1009
(REC B)

• PLUNGER SOLENOID is supplied

as the MECHANICAL BLOCK ASSY.
TRIGGER B TRIG
A DECK/
MOTOR
B DECK
CONTROL
PLUNGER A TRIG
Q331-334

– 27 – – 28 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

– MAIN SECTION –
ECHO PROCESSOR
IC751

2 LPF 1 IN LPF 2 OUT 9

J750 RV750 L-CH
MIC 2
J751
MIC
LEVEL
RV751
ECHO
LEVEL
XRST
IIC DATA
G
MIC 1
VIDEO
R-CH MIX AMP IIC CLK SECTION
IC750(1/2)
IC401
(Page 26)
6 7
(Page 34) SPE SIG
IC411(1/2) IC750(2/2) IC411(2/2)
DISPLAY

E
3 1 MUTE 6 7
SECTION DJ-SIG
Q411 IIC DATA

F DJ-MUTE
EQ
IC111(1/2)
VOLUME
IC111(2/2)
IIC CLK DISPLAY
SECTION
2 RESET (Page 33)
J101
VIDEO IN EQ MUTE
(AUDIO) V AMP 42 41 36 FRONT
64 Q113
L MD
69
TC SELECT
MD IN L 67 SWITCH 60
TU AMP J191
66 &
68 CD SW 58 MUTE SUPER
R-CH 40 6 1
Q191 WOOFER
57

MD OUT L MICON 38 39 SUPER WOOFER

INTERFACE AMP DBFB
IC191 SWITCH
34 33 32 Q141,143
1 2 3
DBFB DBFB
PB L SWITCH
REC L Q111,112

RELAY REC/PB 97 TC RELAY

A SHUT 26 A SHUT
B SHUT 27 B SHUT DBFB H/L 2
B HALF 28 B HALF TA MUTE 1
A HALF 98 A HALF
A PLAY 95 A PLAY SW F RELAY 6 F RELAY

B B PLAY
PB A / B
NORM/HIGH
96
87
93
B PLAY SW
PB A/B
EQ H//N
PL RELAY 8 PL RELAY

DECK BIAS ON/OFF 92 BIAS

XRST 57
SECTION RM ON/OFF 90 REC MUTE
IIC DATA 55
(Page 28) NR ON/OFF 89 NR ON/OFF
REC/PB PASS
CAPM CNT1M
88
85
R/P PASS
CAPM CNT1M
IIC CLK 56
D
CAPM CNT2M 86 CAPM CNT2M POWER
RESET 15
CAPM CNT1P 17 CAPM CNT1P SECTION
CAPM CNT2P 77 CAPM CNT2P (Page 31)
ALC ON/OFF 99 ALC ON/OFF RESET
LM ON/OFF 87 TC MUTE SWITCH
CAP M H/L 82 CAP M H/L Q951
A TRG 83 A TRG
B TRG 84 B TRG AC CUT 16
MS OUT 31 AMS IN MASTER CONTROL
1
3 M62442 LAT IC501
2 RESET
52 M62442 DATA
ST L 3 IC951
51 M62442 CLK
COM DIN
FM/AM TUNER COM DATA 66 ST DIN
D951
TUNER UNIT IS STEREO 70 STEREO
SUPPLIED AS TUNED 69 TUNED
+5V
THE ASSEMBLED ST CE 68 ST CE
X1 11
BLOCK MUTE 72 ST MUTE X501
COM CLK 67 ST DOUT 5MHz
X2 10
65 ST CLK
TBL. L 60 TBL L
TBL. R 61 TBL R XT1 14
76 T SENS X502
T. SENS 32.768KHz
XT2 13 • R CH: Same as L ch
• SIGNAL PATH
DISC SENS
C 75 DISC SENS
OPEN 81 OUT OPEN : FM
POWER 5 POWER ON/OFF
ENC-1 80 ENC1 : CD
CD ENC-2 79 ENC2
SECTION CD POWER 46 CD POWER : PB
ENC-3 78 ENC3
(Page 24) LOAD IN 64 LOAD IN MUTE : REC
STK MUTE 100 SWITCH STK MUTE
LOAD OUT 63 LOAD OUT
Q142
: VIDEO/MD
09

– 29 – – 30 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

– POWER SECTION –
TM402
SURROUND
SPEAKER

R-CH
RELAY R
DRIVE
RY404
Q403,407 RELAY
RY402
DRIVE
Q408

FAN MOTOR M901

DRIVER M FAN
Q961, 962 UNREG MOTOR
PL RELAY –12V
Rch
F RELAY

THERMAL
POWER AMP DET TM401
IC201 Q321,322 SPEAKER
THP321
RY401 FRONT
FRONT 3 12
FRONT L
8 RELAY
DRIVE
J755
Q401,402
PHONES

OVER LOAD
DET
Q201 Rch

Rch
Rch

DBFB PROTECT
CONTROL
Q301-303,
Rch Q306,307
MUTE

D
STK MUTE SWITCH
D5V Q304,305 D+5V
SWITCHED (UNSW) +5V REG
CD +5V IC932
MAIN CD REG D+5V CONTROL
SECTION CD+5V 3 1
Q931 (SW) SWITCH
+5.6V
(Page 30) Q931,932
+5.6V REG
IC931
D932
CD POWER Q932 3 1

+7V REG
IC941
+5V REG M+7V 3 1 T501
AU/D5V SW Q933 POWER
TRANSFORMER
VF
+7V REG
IC901
VF
Q934 A+7V 3 1
RECT
SWITCH +12V REG
Q901 –7V REG D103,
Q911-913
IC902 D104

A–7V
Q905
3 2 • R CH : Same as L ch
Q937 • SIGNAL PATH
SP,MY,EA,HK,TW,IA
: FM
UNREG VF REG RECT
VFDP Q111 D111,112
VOLTAGE • Abbreviation
–12V SELECTOR
S501 EA : Saudi Arabia model.
RECT
+10V REG
D102 SP : Singapore model.
IC911
MY : Malaysia model.
+10V 3 1 POWER B+ RECT
POWER B– D101 HK : Hong Kong model.
AC TW : Taiwan model.
ST+10V 3 1 IN
IA : Indonesian model.
+10V REG
IC921
POWER ON/OFF
09

– 31 – – 32 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

– DISPLAY SECTION –

LED1 79
•
80
• Q601,602
1 LED
IIC DATA 24 SDA PANEL LED D+5V
6 SWITCH
IIC CLK 23 SCL •
11
•
12
•
14
LED15 18
LED PANEL CONTROL
L SEL 25 CONTROL IC801
Q603

REMOTE 19 I2C DATA

DISPLAY CONTROL SIRCS 33 CONTROL 18 I2C CLK S801-808
RESET 10 RESET IC601 RECEIVER
SPEANA 1 34 4 RESET KEY O 38 KEY
IC602
SPEANA 2 35 KEY 1 39 MATRIX
29 SIRCS
SPEANA 3 36
SPEANA 4 37 S601
D801-803
L+R 32 (JOG)
JOG A 21 ROTARY 61 LED
BPM LED B
22 ENCODER SWITCH
JOG B BPM LED A 62
Q854,855
27 JOG A
28 JOG B
KEY 0 26
8 XOUT KEY
X601 MATRIX BOMBER LED 63 PANEL LED
8MHz KEY 3 29

E 9 XIN ON/OFF LED 64

D805 D806

MAIN
SECTION SPEANA
CONTROL
(Page 30) 2 XOUT Q958-960
S602 X501
VOLUME 8MHz MUTE
3 XIN MUTE 5 SWITCH DJ MUTE
VOL A 19 ROTARY Q851
VOL B 20 ENCODER
SEG1-SEG20 GR1-GR13 SOUND MIX
IC851
54 - 57 41 - 53

DATA 14 15 SD
F
FL601,Q70,702 SP1 CLK 15 14 SI MAIN
VF 33 BPF LOW
FLUORESCENT INDICATOR TUBE SP4 LAT 16 8 ST SECTION
36 BPF HIGHT OUT 23 DJ SIG
L+R
37 L+R
CH 13 16 CH (Page 29)
RST 12 17 RST
SPEANA BPF FILTER
IC603 BSY 20 20 BUSY
XT XT
2 3
SP1
F01 17
SP2
F02 16 X851
4 LINE IN SP3
SPE SIG F03 15 4.09MHz
SP4
F04 14
L+R
L+R 13
09

– 33 – – 34 –

Downloaded from www.Manualslib.com manuals search engine

 WAVEFORMS – VIDEO SECTION – – MAIN SECTION –
THIS NOTE IS COMMON FOR PRINTED WIRING
– CD SECTION –
BOARDS AND SCHEMATIC DIAGRAMS. 1
1 8
(In addition to this, the necessary note is printed
1
in each block.) 4Vp-p 5.5Vp-p
5.8Vp-p
1.3Vp-p
For schematic diagrams. 5MHz
10MHz 27MHz
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF IC502 !£ XOUT IC509 1 XT1 IC501 0 X2
50 WV or less are not indicated except for electrolytics IC101 #§ RFAC
2 9 2
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise 2
4Vp-p 5Vp-p
specified. 4.6Vp-p
2.5V
• ¢ : internal component. 32.768kHz
• 2 : nonflammable resistor. 8MHz 44.1kHz
• 1 : fusible resistor. APPROX 500mVp-p
IC402 @º XOUT IC509 !ª LRCK IC501 !£ XT2
• C : panel designation.
IC101 @¶ TE
3 !º
Note: The components identified by mark ! or dotted line 3
with mark ! are critical for safety. 1Vp-p 4.8Vp-p
Replace only with part number specified. 2.5V
– DISPLAY SECTION –
2.11MHz
• U : B+ Line. APPROX 200mVp-p
H
• V : B– Line. IC505 &∞ COUT IC509 !¶ BCLK 1
• H : adjustment for repair. IC101 @ª FE
• Voltages and waveforms are dc with respect to ground 4 !¡ 4Vp-p
under no-signal (detuned) conditions. 4
• Voltages are taken with a VOM (Input impedance 10 MΩ). 2Vp-p 4.8Vp-p
2.6Vp-p 8MHz
Voltage variations may be noted due to normal produc-
tion tolerances. IC601 8 X-OUT
H 33.8MHz
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal pro-
7.5µsec IC505 ^ª YOUT IC504 8 384FS 2
IC101 (§ MDP
duction tolerances. 5 !™ 4.3Vp-p
• Circled numbers refer to waveforms.
• Signal path.
1Vp-p 3.8Vp-p
F : FM 8MHz
g : VIDEO/MD IC801 2 X-OUT
E : PB (DECK A) H 27MHz
d : PB (DECK B) IC401 7 COUT IC504 6 27M 3
G : REC (DECK B)
m : CHROMA 6 !£
3.6Vp-p
n :Y
o : VIDEO 2Vp-p 2.8Vp-p
4.09MHz
J : CD
c : digital out 33.8MHz
IC851 2 TX
H
• Abbreviation IC401 1 YOUT IC504 !™
EA : Saudi Arabia model.
SP : Singapore model. 7
MY : Malaysia model.
1.2
HK : Hong Kong model. Vp-p
TW : Taiwan model.
IA : Indonesian model. H
J302 VOUT
For printed wiring boards.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• p : parts mounted on the conductor side.
• ® : Through hole.
• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)

Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.

• Indication of transistor

C
Q These are omitted
BC E
B E
These are omitted

– 35 – – 36 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-3. SCHEMATIC DIAGRAM – CD SECTION –

• See page 35 for Waveforms.
• See page 85 for IC Block Diagrams.

(Page 47)

– 37 – – 38 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-4. PRINTED WIRING BOARD – CD SECTION –

• See page 22 for Circuit Boards Location.

KSS-213D/Q-NP

• Semiconductor
• Semiconductor Location
Location
Ref. No. Location
Ref. No. Location
IC102 B-2
IC101 B-1 IC104 B-3
IC103 A-2
Q101 A3
Q102 A-2
Q103 A-2
(Page 46)

– 39 – – 40 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-5. SCHEMATIC DIAGRAM – DECK SECTION –

• See page 86 for IC Block Diagrams.

(Page 56)

– 41 – – 42 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-6. PRINTED WIRING BOARD – DECK SECTION –

• See page 22 for Circuit Boards Location.

(Page 53)

– 43 – – 44 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

* Note
8-7. PRINTED WIRING BOARD – VIDEO SECTION – When replacing IC502, refer to “IC502 of
• See page 22 for Circuit Boards Location. video Board” in “Service Note” (page 13). (Page 54)

(Page 39)

• Semiconductor
Location • Semiconductor
Location
Ref. No. Location
Ref. No. Location
D301 E-1
D501 D-3 IC501 C-2
D502 A-3 IC502 B-1
IC506 C-3
IC101 A-1
IC401 E-3 Q302 E-3
IC402 B-2 Q303 D-1
IC504 A-1 Q453 E-2
IC505 C-2 Q454 E-2
IC507 C-1 Q531 D-1
IC509 B-1

Q301 E-1
Q304 D-3
Q306 E-1
Q307 E-2
Q308 E-2
Q310 E-2
Q502 D-3

– 45 – – 46 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-8. SCHEMATIC DIAGRAM – VIDEO (1/3) SECTION – * Note

• See page 36 for Waveforms. When replacing IC502, refer to “IC502 of
• See page 89 for IC Pin Functions. video Board” in “Service Note” (page 13).

(SEE PAGE 12)

(Page 51)

(Page 37)

(Page 58)

(Page 49) (Page 49) (Page 51)

– 47 – – 48 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-9. SCHEMATIC DIAGRAM – VIDEO (2/3) SECTION –

• See page 36 for Waveforms.
• See page 45 for Printed Wiring Board.
• See page 94 for IC Pin Functions.

(Page 47) (Page 47)

(SEE PAGE 12)

(Page 51)

(Page 51)

– 49 – – 50 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-10. SCHEMATIC DIAGRAM – VIDEO (3/3) SECTION –

• See page 36 for Waveforms.
• See page 45 for Printed Wiring Board.

(Page 48)

(Page 48)

(Page 50)

(SEE PAGE 12)

(Page 50)

– 51 – – 52 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

• Semiconductor 8-11. PRINTED WIRING BOARD – MAIN SECTION –

Location • See page 22 for Circuit Boards Location.
Ref. No. Location (Page 83) (Page 83) (Page 46)
D502 C-3
D508 B-1
D901 G-2
D931 H-3
D932 F-3
(Page 72)
D951 D-6
D952 D-6
D953 D-5
D954 D-5
D955 D-6
D956 D-5

IC111 D-10
IC191 E-11
IC301 D-3
IC391 B-12
IC401 G-7
IC411 H-7
IC501 C-5 (Page 43)
IC901 F-2
IC902 G-2
IC911 H-3
IC921 H-2
IC931 G-3
IC932 F-3
IC941 G-5
IC951 D-6

Q111 E-8
Q112 E-8
Q113 E-9
Q141 I-6
Q142 I-7
Q143 H-1
Q161 D-8
Q162 D-8
Q163 E-8
Q191 E-12
Q331 B-3
Q332 B-3
(Page 73)
Q333 B-2
Q334 B-2
Q335 B-3
Q336 A-1
Q337 A-1
Q338 B-1
Q339 B-1
Q340 A-2
Q341 A-2
Q342 B-1
Q343 B-2
Q411 H-6
Q901 G-2
Q902 F-2
Q903 H-2
Q904 G-2
Q905 G-2
Q911 I-4
Q912 H-3
Q913 H-3
Q931 F-2
Q932 E-2
Q933 F-2
Q934 F-2
Q935 F-4
Q936 G-4 (Page 65)
Q937 F-2
Q951 D-5
Q961 I-11
Q962 I-11
(Page 65)

– 53 – – 54 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-12. SCHEMATIC DIAGRAM – MAIN (1/4) SECTION –

(Page 72)
(Page 42)

(Page 57)

(Page 57)

(Page 61)

(Page 61)

(Page 57)

(Page 59) (Page 59) (Page 61)

– 55 – – 56 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818
8-13. SCHEMATIC DIAGRAM – MAIN (2/4) SECTION –
• See page 36 for Waveforms.
• See page 53 for Printed Wiring Board.
• See page 89 for IC Pin Functions.

(Page 56)

(Page 47)

(Page 82)
(Page 56)

(Page 82)

(Page 56)

(Page 61) (Page 61) (Page 62) (Page 62)

– 57 – – 58 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-14. SCHEMATIC DIAGRAM – MAIN (3/4) SECTION –

• See page 53 for Printed Wiring Board.

(Page 55) (Page 55)

(Page 61)

(Page 61)

– 59 – – 60 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-15. SCHEMATIC DIAGRAM – MAIN (4/4) SECTION –

• See page 53 for Printed Wiring Board.

(Page 57) (Page 57) (Page 57) (Page 58)

(Page 56)

(Page
56)

(Page
56)

(Page
60)

(Page
60)

(Page 75) (Page 67) (Page 67)

– 61 – – 62 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-16. SCHEMATIC DIAGRAM – MIC/HP SECTION – 8-17. PRINTED WIRING BOARD – MIC/HP SECTION –
• See page 86 for IC Block Diagrams. • See page 22 for Circuit Boards Location.

(Page 66)

(Page 67)

(Page 65)

(Page 67)

– 63 – – 64 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-18. PRINTED WIRING BOARD – POWER AMP SECTION –

• See page 22 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location

D101 H-6
D102 H-1
D103 I-5
D104 I-5
D111 I-3
D112 I-4
D113 I-3
D114 I-3
D201 F-5
D251 F-4
D301 H-9
D311 G-3
D321 I-5
D331 H-3
D332 H-3
D401 C-2
D402 C-2
D404 B-7
D405 B-2
D406 B-1
D407 B-4
D408 B-4

IC201 D-5

Q111 I-3
Q201 F-5
Q251 F-3
Q301 H-8
Q302 G-7
Q303 H-7
Q304 G-8
Q305 G-7
Q306 G-8
Q307 G-8
Q321 F-3
Q322 E-3
Q401 D-2
Q402 D-1
Q403 D-1
Q407 D-1
Q408 D-2

(Page 54)

(Page 71)

(Page 53) (Page 64)

(Page 64)
– 65 – – 66 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-19. SCHEMATIC DIAGRAM – POWER AMP SECTION –

(Page 63)
(Page 69)

(Page
62)
(Page 69)

(Page
63)

(Page 69)

(Page (Page 69)

62)

(Page 69)

– 67 – – 68 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-20. SCHEMATIC DIAGRAM – TRANSFORMER SECTION –

• See page 65 for Printed Wiring Board. (POWER BOARD)

(Page 68)

(Page 68)

(Page 68)

(Page 68)

(Page 68)

– 69 – – 70 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-21. PRINTED WIRING BOARD – TRANSFORMER SECTION – 8-22. PRINTED WIRING BOARD – LEAF SW SECTION –
• See page 22 for Circuit Boards Location. • See page 22 for Circuit Boards Location.

(Page 53)

8-23. SCHEMATIC DIAGRAM – LEAF SW SECTION –

(Page 56)

(Page 66)

– 71 – – 72 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-24. PRINTED WIRING BOARD – DISPLAY SECTION –

• See page 22 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location
D601 D-2
D602 D-4
D603 D-4
D620 C-10
D621 C-4
D622 C-5
D623 C-6
D624 C-7
D625 C-8
D626 B-3
D627 B-3
D628 A-3
D630 C-2
D651 E-1
D652 E-1
D804 I-17
D805 E-6
D806 E-5
D807 E-9

IC601 B-5
IC602 A-9
IC603 B-7
IC801 E-7
(Page 53)
IC851 E-5

Q601 D-1
Q602 C-1
Q603 C-2
Q607 C-9
Q608 C-4
Q609 C-6
Q610 C-8
Q611 B-2
Q618 E-2 (Page 80)
Q701 A-6
Q702 A-8
Q851 F-6
Q958 E-9
Q959 E-8 (Page 80)
Q960 E-8

(Page 79)

– 73 – – 74 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818
8-25. SCHEMATIC DIAGRAM – DISPLAY SECTION –
• See page 36 for Waveforms.
• See page 86 for IC Block Diagrams.
• See page 97 for IC Pin Functions.

(Page 77)

(Page
61)

(Page 77)

(Page 78)
– 75 – – 76 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-26. SCHEMATIC DIAGRAM – PANEL SECTION –

(Page 76)

(Page 75)

(Page 76)

– 77 – – 78 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-27. PRINTED WIRING BOARD – PANEL SECTION –

• See page 22 for Circuit Boards Location.

(Page 74)

(Page 73)

(Page 74)

– 79 – – 80 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-28. SCHEMATIC DIAGRAM – CD MOTOR SECTION –

• See page 86 for IC Block Diagrams.

(Page 58)

(Page 58)

– 81 – – 82 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-V818

8-29. PRINTED WIRING BOARD – CD MOTOR SECTION –

• See page 22 for Circuit Boards Location.

(Page 54)

(Page 54)

– 83 – – 84 –

Downloaded from www.Manualslib.com manuals search engine

 8-30. IC BLOCK DIAGRAMS
• CD section

IC101 CXD2545Q • VIDEO section • DISPLAY section

VPCO
XTAO
FSTO

XTSL

VCKI
XTAI

IC509 PCM1727E IC603 BA3833F

67 62 63 64 20 19

384fs RESET 1 RESET 18 RESET

32K RAM C
C4M 68 CLOCK XT1 1 CLOCK MANAGER 24 XT2
GENERATOR •
C16M 69 43 PSSL DUAL PLL PREF 2 REFFERENCE 17 f01
PDO 18 CURRENT
RESISTER

VCO1 13 DIGITAL ADDRESS PRIORITY SERIAL

PLL EFM GENERATOR ENCODER
VCO0 12 DEMODULATOR PARALLEL 16 PGND 2 23 DGND BPF DET
PCO 33 ( VARI-PITCH
DOUBLE SPEED ) PROCESSOR
61-46 DA01-16
VCP 3
POWER
SUPPLY 22 VDD
LINE 3
NF
16 f02
FILI 32 21 SCKO1
FILO 31 79 MUTE 20 SCKO2 BPF DET
SYNC D/A NCKO 4 LINE
CLTV 34 PROTECTOR DATA PROCESSOR 4 15 f03
RSV 5 19 LRCK IN
RFAC 36
ASYMMETRY SCKO3 6 AUDIO
ASYI 38 MUX PEAK DETECTOR
CORRECTION DATA INPUT BPF DET
ASYO 39 18 DATA
INTERFACE GND 5 14 f04
ASYE 42 DIGITAL OUT 71 D OUT ML 7
WFCK 73 TIMING MC 8 MODE 17 BCK
SCOR 74 GENERATOR 1 70 MD2 MC 9 CONTROL BPF DET
EXCK 76 ERROR CORRECTOR 10 BIAS 6 13 f
SUBCODE RSTB Bias
C
SBSO 75 P-W 16 ZERO
PROCESSOR 8 TIME OVER OPEN
EMPH 72 86 DATA DET
SUBCODE SAMPLING DIGITAL
SQCK 78 CPU INTERFACE 88 CLOK NC 7 12 VCC
Q FILTER
SQSO 77 87 XLAT 15 CAP
PROCESSOR •
MON 95 FUNCTION
FSW 94 CLV CONTROL
PROCESSOR 14 VOUTL NC 8 11 NC
MDP 96 SERVO
TIMING
MDS 97 AUTO 80 SENS
GENERATOR 2 MULTI LEVEL MULTI LEVEL
18-TIMES SEQUENCER
NOISE BPZ
SHAPER OVERSAMPLING SERVO CONTROL ∆Σ ∆Σ NC 9 10 NC
FILTER MICRO PROGRAM MODULATOR MODULATOR
INTERFACE 89 COUT
MIRR 91 MIRR
DFCT 92 DFCT 5 LEVEL 5 LEVEL
FOK DETECTOR 93 FOK DAC DAC IC851 MSM6653A-517GS-K
RFDC 26
SERVO DSP PWM GENERATOR
TE 27 SWITCH 2 CR LPF CR LPF
A/D SLED PWM 3, 100 SFON, SFDR VDD 1
SE 28 & SLED SERVO 2 VOUTR 11 • •
CONVERTER GENERATOR 1, 2 SRON, SRDR OUTPUT OUTPUT
FE 29 BUFFER XT 2
2 AMP AMP OSC
TRACKING TRACKING PWM 4, 7 TFDR, TFON XT 3 24 GND
VC 30 2
SERVO GENERATOR 5, 6 TRON, TRDR SOUND
2 NC 4 23 A-OUT
8, 11 FFDR, FFON AGND 12 13 VCA MIX
FOCUS SERVO FOCUS PWM CMD 5 22 NAR
GENERATOR 2
9, 10 FRON, FRDR NC
NC 6 21
NC 7 20 BUSY
25 24 14 16 17 21 40 23 35 41 90 15 65 81 22 37 44 45 66 82 83 84 85 98 99 • Deck section ST 8 19 NC
I0 9 18 VPP
RFC
ADIO

TEST
TES2
TES3

AVDD
AVDD
AVSS
AVSS

ADD
ADD
DVSS
DVSS

XRST

IGEN
BIAS
WDCK
LRCK
FSTI
DIRC
SCLK
DFSW
ATSK
LOCK
SSTP

I1 10 17 RST
IC602 uPC1330HA I2 11 µ CON 16 CH
ROM INTER FACE
I3 12 15 SD
14 SI
IC102 BA6392FP IC103 CXA1821M INVERTER 13 I4

BUFF LD 1 VCC 20 VCC

CH1 OUT F 1 F 28 GND
VCC
• MIC/HP section
BUFF BUFF COMPARATER
CH1 OUT R 2 27 CH4 OUT F PD 2 19 LD ON
LEVEL
R
SHIFT 1 2 3 4 5 6 7 8 9 IC751 M65850FP
CAPA IN 1 3 26 CH4 OUT R A 3 APC LD AMP 18 LC/PD SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2

LPF2OUT
VREF

OP2OUT
BUFF

LPF2IN
CLOCK

OP2IN
R VEE VEE RF EQ AMP VCC

REF
CH1 R IN 4 25 VB IN
B 4 17 RFE
INTERFACE
CH1 F IN 5
F
24 VS IN VC • CD motor section 14 13 12 11 10 9 8
BUFF C 5 RF SUMMING AMP VC 16 RFO
VREF IN 6 23 VB IN OSCILLATOR
IC701 M54641L D/A LPF2
D 6 15 FE
VCC VCC
VREF OUT 7 22 VCC FOCUS ERROR AMP 1/2 VCC
1 8
VEE 7 VEE 14 FE BIAS CLOCK DO1
TRACKING ERROR AMP MO
GND 8 21 VCC VC REG 5 REFERENCE AUTO MAIN 20KBIT
VC RESET
VC RESET CONTROL SRAM
CH2 F IN 9
F F
20 CH3 F IN F 8 13 TE IC801 BA6286N D1
MI
DO0
POWER 2 OUT2
INTERFACE INTERFACE VC VC INPUT AMP.
R R IN1 3 AMP.
CH2 R IN 10 19 CH3 R IN E 9 VC BUFFER 12 VC A/D
GND 1 PO WER
VC VCC CONTROL SAVE LPF1
CAPA IN 2 11 R F 18 CAPA IN 3 RIN 2
EI 10 VEE 11 EO POWER 7 OUT1 VREF
INPUT AMP. 3
BUFF BUFF IN2 6 AMP. 1 2 3 4 5 6 7
CH2 OUT R 12 17 CH3 OUT R OUT2 4
LPF1IN

LPF1OUT

OP1OUT
OP1IN
CC1

CC2

GND

F R RNF 5
BUFF BUFF TSD CONTROL
CH2 OUT F 13 16 CH3 OUT F GND 6 LOGIC
4
MUTE OUT1 7
GND
GND 14 15 MUTE VM 8
VCC 9
FIN 10

– 85 – – 86 –

Downloaded from www.Manualslib.com manuals search engine

 8-31. IC PIN FUNCTIONS
• IC101 DIGITAL SIGNAL PROCESSOR (CXD2545Q)/BD board
Pin No. Pin Name I/O Function
1 SRON O Sled drive output (Not used)
2 SRDR O Sled drive output
3 SFON O Sled drive output (Not used)
4 TFDR O Tracking drive output
5 TRON O Tracking drive output (Not used)
6 TRDR O Tracking drive output
7 TFON O Tracking drive output (Not used)
8 FFDR O Focus drive output
9 FRON O Focus drive output (Not used)
10 FRDR O Focus drive output
11 FFON O Focus drive output (Not used)
12 VCOO O VCO output for analog EFM (Eight to Fourteen Modulation) PLL (Not used)
13 VCOI I VCO input from analog EFM PLL (Ground)
14 TEST I TEST pin connected normally to ground
15 DVSS – Digital ground
16 TES2 I TEST pin connected normally to ground
17 TES3 I TEST pin connected normally to ground
18 PDO O Charge-pump output for analog EFM PLL (Not used)
19 VPCO O Charge-pump output for variable pitch PLL (Not used)
20 VCKI I Clock input from variable pitch external VCO
21 AVD2 – Analog power supply
22 IGEN I Power supply pin for operational amplifiers
23 AVS2 – Analog ground
24 ADIO I (Not used)
25 RFC O (Not used)
26 RFDC I RF signal input
27 TE I Tracking error signal input
28 SE I Sled error signal input
29 FE I Focus error signal input
30 VC I Center voltage input pin
31 FILO O Filter output for master PLL
32 FILI I Filter input for master PLL
33 PCO O Charge-pump output for master PLL
34 CLTV I Control voltage input for master VCO
35 AVS1 – Analog ground
36 RFAC I EFM signal input
37 BIAS I Asymmetry circuit constant current input
38 ASYI I Asymmetry comparate voltage input
39 ASYO O EFM full swing output
40 AVD1 – Analog power supply
41 DVDD – Digital power supply
42 ASYE I Asymmetry circuit ON/OFF
43 PSSL I Audio data output mode selection input
44 WDCK O 48-bit slot D/A interface. word clock. (Not used)
45 LRCK O 48-bit slot D/A interface. LR clock.
46 DATA O DA 16 output when PSSL=1. 48-bit slot serial data when PSSL=0
47 BCLK O DA 15 output when PSSL=1. 48-bit slot data when PSSL=0
48 64DATA O DA 14 output when PSSL=1. 64-bit slot data when PSSL=0 (Not used)
49 64BCLK O DA 13 output when PSSL=1. 64-bit slot data when PSSL=0 (Not used)
50 64LRCK O DA 12 output when PSSL=1. 64-bit slot data when PSSL=0 (Not used)
– 87 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
51 GTOP O DA 11 output when PSSL=1. GTOP output when PSSL=0 (Not used)
52 XUGF O DA 10 output when PSSL=1. XUGF output when PSSL=0 (Not used)
53 XPLCK O DA 09 output when PSSL=1. XPLCK output when PSSL=0 (Not used)
54 GFS O DA 08 output when PSSL=1. GFS output when PSSL=0 (Not used)
55 RFCK O DA 07 output when PSSL=1. RFCK output when PSSL=0
56 C2PO O DA 06 output when PSSL=1. C2PO output when PSSL=0
57 XRAOF O DA 05 output when PSSL=1. XRA0F output when PSSL=0 (Not used)
58 MNT3 O DA 04 output when PSSL=1. MNT3 output when PSSL=0
59 MNT2 O DA 03 output when PSSL=1. MNT2 output when PSSL=0
60 MNT1 O DA 02 output when PSSL=1. MNT1 output when PSSL=0
61 MNT0 O DA 01 output when PSSL=1. MNT0 output when PSSL=0
62 XTAI I X’tal oscillator circuit input
63 XTAO O X’tal oscillator circuit output
64 XTSL I X’tal selection input pin
65 DVSS – Digital ground
66 FSTI I 2/3 divider input of pins 62, 63
67 FSTO O 2/3 divider output of pins 62, 63
68 FSOF O (Not used)
69 C16M O 16.9344 MHz output (Not used)
70 MD2 I Digital-out ON/OFF control pin (+5V)
71 DOUT O Digital-out output pin
72 EMPH O Playback disc output in emphasis mode (Not used)
73 WFCK O WFCK (Write Frame Clock) output
74 SCOR O Sub-code sync output
75 SBSO O Sub-P through Sub-W serial output (Not used)
76 EXCK I Clock input for SBSO read-out
77 SUBQ O Sub-Q 80-bit output
78 SQCK I Clock input for SQSO read-out
79 MUTE I Muting selection pin
80 SENS O SENS output
81 XRST I System reset
82 DIRC I Used in 1-track jump mode (+5V)
83 SCLK I SENS serial data read-out clock
84 DFSW I Defect selection pin (Ground)
85 ATSK I Input pin for anti-shock (Ground)
86 DATA I Serial data input, supplied from CPU
87 XLAT I Latch input, supplied from CPU
88 CLOK I Serial data transfer clock input, supplied from CPU
89 COUT O Numbers of track counted signal output (Not used)
90 DVDD – Digital power supply
91 MIRR O Mirror signal output
92 DFCT O Defect signal output (DFCT: Defect)
93 FOK O Focus OK output
94 FSW O Output to select spindle motor output filter (Not used)
95 MON O Output to control ON/OFF of spindle motor (Not used)
96 NDP O Output to control spindle motor servo
97 MDS O Output to control spindle motor servo (Not used)
98 LOCK O GFS (Guarded Frame Sync) is sampled by 460 Hz. H when GFS is H (Not used)
99 SSTP I Input signal to detect disc inner most track
100 SFDR O Sled drive output

– 88 –
Downloaded from www.Manualslib.com manuals search engine
 • IC501 MASTER CONTROL (uPD780016AYGF-014-3BA)

Pin No. Pin Name I/O Function

1 LINE-MUTE O Line mute signal output
2 DBFB-H/L O DBFB H/L select signal output
3 M62442-LAT O Latch signal output for IC111 (M62442FP)
4 KCON-LAT O Not used
5 POWER O Power ON/OFF signal output
6 F-RELAY O Front speaker relay control output
7 R-RELAY O Rear speaker relay control output (Not used)
8 PL-RELAY O Surround speaker relay control output
9 VSS – Ground
10 X2 O
X’tal (5MHz)
11 X1 I
12 VDD – Power supply (+5V)
13 XT2 O
X’tal (32.768 KHz)
14 XT1 I
15 RESET I Reset signal input
16 (AC-CUT) I Back up signal input
17 CAPM-CNT1P I Capstan motor control 1 (+) signal output
18 SCOR O Subcode data request signal output
19 SOFT-TEST O Software test port
20 — – Not used
21 RDS-INT I RDS data interrupt input (Connected to ground)
22 RDS-DATA I RDS data interrupt input (Connected to ground)
23 AVDD – Power supply (+5V)
24 AVREF I Analog reference voltage input.
25 ADJ I CD adjust point port Normal “H”
26 A-SHUT I A Deck reel pulse detector
27 B-SHUT I B Deck reel pulse detector
28 B-HALF I Half detector signal input
29 CLK-CHECK I Connected to ground
30 SPEC-IN I Version select signal input
31 AMS-IN I Connected to ground
32 DEMO-CHANGE I DEMO H/L select signal input (Connected to ground)
33 AVSS – Ground
34 SQ-DATA-IN I Subcode Q data clock input (Connected to ground)
35 — – Not used
36 SQ-CLK I Not used
37 SUR-ON/OFF O Not used
38 FB CONT-A I Not used
39 FB CONT-B I Connected to ground
40 VSS – Ground
41 PL-VOL O Not used
42 PL-LAT O Not used
43 COM-DIN I Connected to ground
44 COM-DOUT O Common serial data output (Not used)

• Abbreviation
APC : Auto Power Control

– 89 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
45 COM-CLK O Common serial clock output
46 CD-POWER O CD power on signal output
47 CD-DATA O Not used
48 CD-CLK O Not used
49 PL-CLK O Not used
50 PL-DATA I Not used
51 M62442-CLK O Clock signal output for IC111 (M62442FP)
52 M62442-DATA O Data signal output for IC111 (M62442FP)
53 LEVEL-CONT-A O Not used
54 LEVEL-CONT-B O Not used
55 IIC-DATA O Data output for IC502
56 IIC-CLK O Clock output for IC502
57 XRST O CD reset signal output
58 XLT O Not used
59 FCS-SW O Not used
60 TBL-L O
Table motor control output
61 TBL-R O
62 — O Not used
63 LOAD-OUT O
Loading motor control signal output
64 LOAD-IN O
65 ST-CLK O Tuner clock output
66 ST-DIN I Tuner data input
67 ST-DOUT O Tuner data output
68 ST-CE O Tuner chip enable output
69 TUNED I Tuned detection for tuner
70 STEREO I Stereo detection for tuner
71 VSS – Ground
72 ST-MUTE O Tuner mute signal output
73 SENS2 I BD Condition signal input
74 SENS I Not used
75 DISC-SENS I Slit sensor of disc table input
76 T-SENS I CD table detection signal input
77 CAPM-CNT2P O Capstan motor control 2 (+) signal output
78 ENC 3 I
79 ENC 2 I Disc tray adrress detect encoder input
80 ENC 1 I
81 OUT-OPEN O Loading out detection signal output
82 CAP-M-H/L O Capstan motor H/N speed select signal output
83 B-TRG O Trigger motor control output
84 A-TRG O Trigger motor control output
85 CAPM-CONT1M O Capstan motor control 1 (–) signal output
86 CAPM-CONT2M O Capstan motor control 2 (–) signal output
87 TC-MUTE O TC mute ON/OFF selection output

– 90 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
88 R/P-PASS O REC/PB/PASS selection output
89 NR-ON/OFF O NR ON/OFF signal output
90 REC-MUTE O REC mute ON/OFF selection output
91 CLK-OUT O Clock out signal check
92 BIAS O Bias ON/OFF signal output
93 EQ-H/N O Equalizer H/N select output
94 PB-A/B O PB Deck A/Deck B select output
95 A-PLAY-SW I Deck A play detect
96 B-PLAY-SW I Deck B play detect
97 TC-RELAY O REC/PB head selection output for IC602
98 A-HALF I Deck A cassette detect
99 ALC-ON/OFF O ALC ON/OFF output signal
100 STK-MUTE O Power amp ON/OFF signal output

– 91 –
Downloaded from www.Manualslib.com manuals search engine
 • IC502 MPEG DECODER, MECHANISM CONTROL (M30620MC-302FP or M30620MC-305FP)

Pin No. Pin Name I/O Function

1 SENSE I Internal state (SENSE) monitor input (IC101)
2 SENSE CLK O Serial data reading clock output (IC101)
3 DSP DATA O Serial data output (IC101)
4 DSP LATCH O Lach output (IC101)
5 DSP CLK O Serial data clock output (IC101)
6 TSENS I Not used
7 REMOTE IN I Not used
8 BYTE I External bus width change input (Connected to ground)
9 VSS – Ground
10 DSP MUTE O Mute output (IC101) “H” : mute
11 CTRL1 (L : DOUBLE) O Double change output (IC101) “L” : double
12 XRESET I System reset input “L” : reset
13 XOUT O Main clock output (10MHz)
14 VSS – Ground
15 XIN I Main clock input (10MHz)
16 VCC – +5V power supply
17 NMI I Requests mask disable interruption input (Connected to +5V)
18 SCOR I Subcode sync input (IC101)
19 D SENS I Not used
20 CL680 INT I Video CD interruption input (IC505)
21 CL680 HSEL O Video CD select data of the host MPU (IC505)
22 DF LATCH O Digital filter latch output (IC509)
23 CL680 HRDY I Ready signal input for communication to the host MPU (IC505)
24 680 RESET O Video CD reset output (IC505) “L” : reset
25 JOG1 I Not used
26 JOG2 I Not used
27 CTRL2 O Double control output (IC101) “H” : double
28 LD ON O Laser diode ON/OFF output
29 IIC1 I/O IIC convertion microcomputer receive data (Former type), IIC clock input from master control (New type)
30 IIC0 I/O IIC convertion microcomputer transmittion data (Former type), IIC data input from master control (New type)
31 DATA1O O Serial 1 data output (IC505, 509)
32 DATA1I I Serial 1 data input (IC505, 509)
33 CLK1 O Serial 1 clock output
34 SHARPNESS O Sharpness output L : normal, H : sharpness
35 XVLEVEL. DOWN O Fix the video signal output level output
36 SUBQ DATA I Serial 2 data input for subcode sync reading
37 SUBQ CLK I Serial 2 clock input for subcode sync reading
38 P. ON I Not used
39 BUS XRDY I Not used
40 BUS I Not used
41 BUS XHOLD I Not used
42, 43 BUS I Not used
44 BUS XRD I Model selection input “L” : chinese model, “H” : except chinese model
45 BUS I V sync signal input

NOTE:
When use the IC402 : Former type
When not use the IC402 : New type

– 92 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
46 BUS XWRL I Not used
47 LO. BOOST I Not used
48 AUDIO MUTE O Audio mute output “L” : mute
49 LOAD OUT I Not used
50 LOAD IN I Not used
51 INSW I Not used
52 OUTSW I Not used
53 MODEL 1 I L : System input (Fixed at “L”)
54 MODEL 2 I L : System input (Fixed at “L”)
55 TBLL I Not used
56 TBLR I Not used
57 ENC 1 I Not used
58 ENC 2 I Not used
59 ENC 3 I Not used
60 — I Not used
61 — I Not used
62 VCC – +5V power supply
63 — I Not used
64 VSS – Ground
65 A7 O Video mute output “L”
66 to 71 A6 to A1 I Not used
72 U to I I IIC convertion microcomputor transmittion input
73 TEST LED O TEST LED for MPEG decoder
74 TEST 1 I Test mode for Video CD check
75 TEST 2 I Test mode for servo check
76 TEST 3 I Not used
77 DEVICE RESET O Device system rest output “L” : reset
78 STANDBY I Not used
79 FL CS I Not used
80 FL I Not used
81 to 88 D7 to D0 I Not used
89 MIC CTRL I Not used
90 KEY 1 I Not used
91 KEY 2 I Not used
92 KEY 3 I Not used
93 NY/PAL I NTSC/PAL select switch input
94 MUSIC VOL I Not used
95 KEY 4 I Not used
96 AVSS – A/D converter ground
97 MODE. SW I Not used
98 VREF I A/D converter reference voltage input (Connected to +5V)
99 AVCC – A/D converter +5V power supply
100 AMP. ON I Not used

– 93 –
Downloaded from www.Manualslib.com manuals search engine
 • IC505 CD DECODER, SYSTEM CONTROL (CL680T-D1)

Pin No. Pin Name I/O Function

1 NC – Not used
2 VSS – Ground
3 CD-BCK I CD Decode bit clock
4 CD-DATA I CD Decode data
5 CD-LRCK I CD Decode Left or Right channel selection clock
6 CD-C2PO I CD Decode C2 error data
7 NC – Not used
8 NC – Not used
9 NC – Not used
10 MD0 I/O Data bus between Microcode ROM/DRAM and CL680
11 MD1 I/O Data bus between Microcode ROM/DRAM and CL680
12 MD2 I/O Data bus between Microcode ROM/DRAM and CL680
13 MD3 I/O Data bus between Microcode ROM/DRAM and CL680
14 MD4 I/O Data bus between Microcode ROM/DRAM and CL680
15 MD5 I/O Data bus between Microcode ROM/DRAM and CL680
16 VSS – Ground
17 MD6 I/O Data bus between Microcode ROM/DRAM and CL680
18 VDD3 – +3.3V Power supply
19 MD7 I/O Data bus between Microcode ROM/DRAM and CL680
20 VSS – Ground
21 MD8 I/O Data bus between Microcode ROM/DRAM and CL680
22 VDD3 – +3.3V Power supply
23 MD9 I/O Data bus between Microcode ROM/DRAM and CL680
24 MD10 I/O Data bus between Microcode ROM/DRAM and CL680
25 MD11 I/O Data bus between Microcode ROM/DRAM and CL680
26 MD12 I/O Data bus between Microcode ROM/DRAM and CL680
27 MD13 I/O Data bus between Microcode ROM/DRAM and CL680
28 MD14 I/O Data bus between Microcode ROM/DRAM and CL680
29 MD15 I/O Data bus between Microcode ROM/DRAM and CL680
30 NC – Not used
31 NC – Not used
32 NC – Not used
33 NC – Not used
34 NC – Not used
35 NC – Not used
36 NC – Not used
37 MCE O Chip enable signal to Microcode ROM
38 MWE O Write enable signal to DRAM
39 VSS – Ground
40 CAS O Column address strove : Latch the column address to DRAM
41 VDD3 – +3.3V power supply
42 RAS0 O Row address strove : Latch row address to DRAM
43 RAS1 – Not used
44 MA10 O Address data from CL680 to Microcode ROM
45 MA9 O Address data from CL680 to Microcode ROM

– 94 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
46 MA8 O Address data from CL680 to Microcode ROM/DRAM
47 VSS – Ground
48 MA7 O Address data from CL680 to Microcode ROM/DRAM
49 VDD3 – +3.3V Power supply
50 MA6 O Address data from CL680 to Microcode ROM/DRAM
51 MA5 O Address data from CL680 to Microcode ROM/DRAM
52 MA4 O Address data from CL680 to Microcode ROM/DRAM
53 VSS – Ground
54 MA3 O Address data from CL680 to Microcode ROM/DRAM
55 VDD3 – +3.3V Power supply
56 MA2 O Address data from CL680 to Microcode ROM/DRAM
57 MA1 O Address data from CL680 to Microcode ROM/DRAM
58 MA0 O Address data from CL680 to Microcode ROM/DRAM
59 PGIO7 I/O Not used
60 RESET I Reset signal input from the host MPU
61 VDDMAX-IN I Fix the maxium input voltage each input pin and I/O pin
62 NC – Not used
63 NC – Not used
64 NC – Not used
65 AGND DAC – Ground
66 AVDD DAC – +3.3V Power supply
67 COMPOS OUT O Not used
68 AGND DAC – Ground
69 Y-OUT O Luminance signal out
70 AVDD DAC – +3.3V Power supply
71 AGND DAC – Ground
72 RREF I Fix the video signal output level
73 (1.235V) VREF O Reference voltage (+1.235V)
74 AVDD DAC – +3.3V Power supply
75 C-OUT O Chrominance signal out
76 AGND DAC – Ground
77 (GCK INT) CLK SEL I GCK selection “H”; Internal, “L”; External
78 CLK SEL I DA-XCK selection (1)
79 CLK SEL I DA-XCK selection (2)
80 VSS – Ground
81 RESERVED I Selection the operation clock 42.336MHz
82 VDD3 – +3.3V Power supply
83 DA-EMP – Not used
84 RESERVED – Not used
85 AGND PLL – Ground
86 DA-XCLK I Main reference clock input (16.9344MHz=384fs)
87 AVDD PLL – +3.3V
88 PGIO4 I/O Not used
89 PGIO5 I/O Not used
90 PGIO6 I/O Not used

– 95 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
91 PGIO0 I/O Not used
92 PGIO8 I/O Not used
93 PGIO2/VSYNC/CSYNC O Vertical synchronized signal of video signal
94 AVDD PLL – +3.3V Power supply
95 NC – Not used
96 NC – Not used
97 NC – Not used
98 AGND PLL – Ground
99 VSS – Ground
100 NC – Not used
101 PGIO3/HSYNC I/O Not used
102 VDD3 – +3.3V Power supply
103 PGIO1/VCK-OUT I/O Not used
104 VSS – Ground
105 GCK I Not used
106 VCK-IN I Main clock for video signal processer
107 GCKOUT/DA-EMP O Not used
108 DA-LRCK O Digital Audio Left or Right channel selection clock
109 VDDMAX-OUT O Fix the maxium output voltage certain output pins (Connected to +5V)
110 DA-DATA O Digital Audio data
111 DA-BCK O Digital Audio bit clock
112 HD-OUT O Serial Data output from CL680 to the host MPU
113 HRDY O Ready signal CL680 is ready for communication to the host MPU
114 HINT O Request signal for interrupting the host MPU
115 CDG-SCK I/O Not used
116 VSS – Ground
117 HCK I Host clock : referance signal for the host bus interface
118 VDD3 – +3.3V Power supply
119 HD-IN I Serial Data output ftom the host MPU to CL680
120 VDD3 – +3.3V Power supply
121 HSEL I Select data or address of the host MPU
122 CDG-SDATA I Ground (Not used)
123 CDG-VFSY I Ground (Not used)
124 CDG-SOS1 I Ground (Not used)
125 NC – Not used
126 NC – Not used
127 NC – Not used
128 NC – Not used

– 96 –
Downloaded from www.Manualslib.com manuals search engine
 • IC601 DISPLAY CONTROL ( TMP87CM74AF)
Pin No. Pin Name I/O Function
1 to 6 LED3 to LED8 O LED driver output
7 VSS – Ground
8 X OUT O
X’tall (8MHz)
9 X IN I
10 RESET I Reset signal input from main controller
11 LED9 O
LED driver output
12 LED10 O
13 TEST I Connected ground
14 to 18 LED11 to LED15 O LED driver output
19 VOL A I
Rotary encoder (S602) pulse input
20 VOL B I
21 JOG A I
Rotaly encoder (S601) pulse input
22 JOG B I
23 SCL O Serial clock input from master controller
24 SDA O Serial data input from master controller
25 L. SEL O LED select signal output
26 to 29 KEY 0 to KEY 3 I Key input
30 MODEL I Version select signal input
31 (LED 16 OPEN) – LED driver output (Not used)
32 L+R I Spectrum analyzer (high frequency) input
33 SIRCS I Remote commander signal input
34 to 37 SPEANA 1 to SPEANA 4 I Spectrum analyzer input
38 VASS – Ground
39 VAREF I Analog reference voltage input
40 VDD – Power supply (+5V)
41 to 53 GR 1 to GR13 O FL gride signal output
54 to 77 SEG 1 to SEG 24 O FL segment signal output
78 VKK – Power supply (–25V) for FL segment signal output
79 LED 1 O
LED driver output
80 LED 2 O

• Abbreviation
FL : Fluorescent indicator tube

– 97 –
Downloaded from www.Manualslib.com manuals search engine
 • IC801 PANEL CONTROL ( TMP87CH48DF)

Pin No. Pin Name I/O Function

1 VSS – Ground
2 X OUT O
X’tall (8MHz)
3 X IN I
4 RESET I Reset signal input
5 MUTE I Mute ON/OFF selection input
6 MODE_0 I
7 TEST –
Connected to ground
8 MODE_1 I
9 YB_CLK O
10 NAR/YB_RDY I Connected to VDD
11 MSM6654/BSY I Busy signal input for IC851 (MSM6653A)
12 MSM6654/RST O Reset signal output for IC851 (MSM6653A)
13 MSM6654/CH O Channel signal output for IC851 (MSM6653A)
14 MSM6654/DATA O Data signal output for IC851 (MSM6653A)
15 MSM6654/CLK O Clock signal output for IC851 (MSM6653A)
16 MSM6654/LAT O Latch signal output for IC851 (MSM6653A)
17 YB_D0 I Connected to ground
18 IC2 CLK I Serial clock input from master controller
19 IC2 DATA I Serial data input from master controller
20 YB_D3 I
21 UART RX I Connected to ground
22 UART TX O
23 to 26 NC O Connected to ground
27 JOG_A I
Rotary encoder (S601) pulse input
28 JOG_B I
29 SIRCS I Remote commander signal input
30 VASS – Ground
31 VAREF I Analog reference voltage input
32 DVDD – Power supply (+5V)
33 BPF/LOW I Spectrum analyzer input
34 BPF/LOW-MID I Connected to ground
35 BPF/HIGH-MID I Connected to ground
36 BPF/HIGH I Spectrum analyzer input
37 L+R I Spectrum analyzer (high frequency) input
38 KEY/0 I
Key input
39 KEY/1 I
40 KEY/2 I Connected to VDD
41 to 56 NC O Not used
57 to 60 GND – Ground
61 BPM_LED_B O
62 BPM_LED_A O
LED Drive output
63 BOMBER_LED O
64 ON/OFF_LED O

– 98 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 9
EXPLODED VIEWS
NOTE: The components identified by
• Items marked “*” are not stocked since they are • Abbreviation
mark ! or dotted line with mark
seldom required for routine service. Some delay EA : Saudi Arabia model
! are critical for safety.
should be anticipated when ordering these items. HK : Hong Kong model Replace only with part number
• The mechanical parts with no reference number in SP : Singapore model
specified.
the exploded views are not supplied. MY : Malaysia model
• Hardware (# mark) list and accessories and packing TW : Taiwan model
materials are given in the last of this parts list. IA : Indonesian model

9-1. CASE SECTION

CDM38L-5BD24AL
1 #2
#2
2 #2 11
9

10
#2
3
#2 #2
#5
#1 #2
2 #2

5
#2
M901
Front panel #2
#2
3
#3

8
6
4

#3

#2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-996-816-01 CASE 6 1-693-421-11 TUNER (FM/AM)
2 3-363-099-71 SCREW (CASE 3 TP2)
3 3-363-099-11 SCREW (CASE 3 TP2) 7 4-991-781-01 EMBLEM (VCD)
4 4-900-740-01 PANEL, LOADING 8 1-773-009-11 WIRE (FLAT TYPE) (15 CORE)(150mm)
* 5 4-999-907-01 PANEL, BACK (SP,MY) 9 1-775-212-11 WIRE (FLAT TYPE) (23 CORE)
10 1-690-589-31 WIRE (FLAT TYPE) (13 CORE)
* 5 4-999-907-11 PANEL, BACK (EA) * 11 A-4414-188-A VIDEO BOARD, COMPLETE
* 5 4-999-907-31 PANEL, BACK (HK)
* 5 4-999-907-41 PANEL, BACK (TW) M901 1-763-048-21 FAN, D.C.
* 5 4-999-907-51 PANEL, BACK (IA)

– 99 –
Downloaded from www.Manualslib.com manuals search engine
 9-2. CHASSIS SECTION

not supplied
#5 53

54

#5
60
58 (HK)
51
58 (SP,MY,EA,TW)

58 (IA)
#4
#5 55
59 (SP,MY,EA,
52 HK,TW)

59 (IA)
T501 #6 56

#6 #6

#5

not supplied
#5

57

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 51 A-4407-260-A POWER BOARD, COMPLETE 57 4-965-822-01 FOOT
(Indonesia Product)(SP,MY,EA,HK,IA,TW) ! 58 1-569-007-11 ADAPTOR, CONVERSION 2P (IA)
51 A-4407-498-A POWER BOARD, COMPLETE
(Malaysia Product)(MY) ! 58 1-569-008-21 ADAPTOR, CONVERSION 2P (SP,MY,EA,TW)
* 52 1-668-274-11 TRANSFORMER BOARD ! 58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
* 53 A-4414-035-A MAIN BOARD, COMPLETE ! 59 1-558-943-41 CORD, POWER (IA)
54 1-773-041-11 WIRE (FLAT TYPE) (17 CORE) ! 59 1-575-651-21 CORD, POWER (SP,MY,EA,HK,TW)
60 1-783-898-11 WIRE (FLAT TYPE) (15 CORE)
55 3-703-244-00 BUSHING (FBS001), CORD (SP,MY,EA,HK,TW)
55 4-966-266-01 BUSHING (S) (FBS002), CORD (IA) ! T501 1-431-828-11 TRANSFORMER, POWER
* 56 4-988-533-01 HOLDER, PWB

– 100 –
Downloaded from www.Manualslib.com manuals search engine
 9-3. FRONT PANEL SECTION

not supplied 123

123
not supplied 118
126

123
125
119
123
120
125
123 123
supplied with 117
J750,751
110
ND601 120
123
121
123
127 TCM230AWR1
129 111 116 123 TCM230PWR1
116 115
122
107 #7 123
107
105 123
103
108 122
123
#7
123
123
not supplied 114 124 123
not supplied #2
113
101
102 104
109
128 106
not supplied
supplied
112 with J755
123
130

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 4-996-808-01 WINDOW (TCL) * 117 1-668-268-11 CD SW BOARD
102 4-996-809-01 WINDOW (TCR) * 118 A-4414-042-A PANEL BOARD, COMPLETE
103 4-996-799-01 LID (A), CASSETTE * 119 4-996-796-11 HOLDER, FL TUBE
104 4-996-800-01 LID (B), CASSETTE * 120 4-932-810-31 CUSHION (FL)
105 4-900-600-01 SPRING (A DECK)
121 1-769-972-11 WIRE (FLAT TYPE) (13 CORE)
106 4-900-601-01 SPRING (B DECK) * 122 3-973-975-21 DAMPER, OIL
107 4-959-229-11 DETENT, CASSETTE 123 4-951-620-01 SCREW (2.6X8), +BVTP
108 4-996-810-01 KNOB (JOG) * 124 1-668-271-11 HP BOARD
109 4-996-811-01 KNOB (VOL) 125 4-986-893-51 KNOB (MICROPHONE)
110 X-4949-982-1 PANEL ASSY, FRONT
* 126 A-4414-041-A MIC BOARD, COMPLETE
111 4-962-708-21 EMBLEM (4-A), SONY 127 X-4949-941-1 LID (L) ASSY, CASSETTE
112 4-988-663-01 FOOT (FELT) 128 X-4949-942-1 LID (R) ASSY, CASSETTE
113 A-4407-476-A CONT COM BOARD, COMPLETE 129 4-995-081-01 LATCH, DC
* 114 1-668-269-11 DECO BOARD 130 1-773-108-11 WIRE (FLAT TYPE) (19 CORE)
115 4-996-812-01 HOLDER (LED)
ND601 1-517-731-21 INDICATOR TUBE, FLUORESCENT
116 4-996-716-01 HOLDER (CDM)

– 101 –
Downloaded from www.Manualslib.com manuals search engine
 9-4. CD MECHANISM DECK SECTION-1 (CDM38L-5BD24AL)

201

202

201 206
#2
203 M701
204
211 #8

205

207
208

210
212

209

#2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 4-981-789-01 BRACKET (2), YOKE 208 4-977-941-01 BEARING (WORM)
202 4-977-945-01 TRAY (TURN) * 209 1-658-576-11 SENSOR BOARD
203 X-4946-665-1 SHAFT ASSY, WORM 210 4-934-376-01 SHAFT (ROLLER)
204 4-977-943-01 BELT (TURN) (1.2)
205 4-977-956-01 WHEEL, WORM 211 4-981-187-01 COLLAR (WORM)
212 4-977-944-01 TRAY (SLIDE)
* 206 1-658-577-11 MOTOR (TURN) BOARD M701 A-4672-004-A MOTOR ASSY (TURN)
207 4-988-162-01 ROLLER

– 102 –
Downloaded from www.Manualslib.com manuals search engine
 9-5. CD MECHANISM DECK SECTION-2 (CDM38L-5BD24AL)

251

251 253 252

255

254

257

258
not
supplied
256

259
266 270
#2
260
267
269
268
261
261 M801

BU-5BD24AL

S811 262

263

#2
263

264

265
251

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 4-917-583-71 BRACKET, YOKE * 262 1-658-578-11 MOTOR (SLIDE) BOARD
252 4-977-954-01 PULLEY (SL) 263 4-982-447-01 SPRING (BU), COMPRESSION
253 4-977-953-01 GEAR (SL-A) 264 4-951-620-41 SCREW (2.6), +BVTP
254 4-977-955-01 GEAR (SL-B) * 265 X-4946-666-1 HOLDER (BU) ASSY
255 4-977-942-01 BELT (SL) (1.4)
266 4-989-494-01 SCREW (SLIDER), STEP
256 X-4946-667-1 CAM ASSY, BU 267 4-989-492-21 SLIDER (38)
257 1-452-879-11 MAGNET 268 4-989-819-02 SPRING, TENSION
258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE) 269 4-989-491-21 COVER, LENS
* 259 1-658-575-11 CONNECTOR BOARD 270 4-994-963-01 PULLEY (LBT), PRESS
* 260 X-4946-668-1 CHASSIS (CDM) ASSY
M801 A-4672-004-A MOTOR ASSY (SLIDE)
261 4-985-672-01 SCREW (+PTPWH M2.6X6), FLOATING S811 1-473-335-11 ENCODER, ROTARY (BU, TRAY ADDRESS DET)

– 103 –
Downloaded from www.Manualslib.com manuals search engine
 9-6. BASE UNIT SECTION (BU-5BD24AL)

301

302

#9

303

305
M101 304
M102

304

306

307

308

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! 301 8-820-020-02 OPTICAL PICK-UP BLOCK KSS-213D/Q-NP 306 4-917-564-01 GEAR (P), FLATNESS
302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) * 307 A-4699-697-A BD BOARD, COMPLETE
303 4-917-567-01 GEAR (M) 308 4-951-620-01 SCREW (2.6X8), +BVTP
304 4-951-940-01 INSULATOR (BU) M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
305 4-917-565-01 SHAFT, SLED M102 X-4917-504-1 MOTOR ASSY (SLED)

– 104 –
Downloaded from www.Manualslib.com manuals search engine
 9-7. TC MECHANISM SECTION 1 TCM230AWR1
TCM230PWR1 ( )
*NOTE: Two types of parts which are not interchangeable are available
for the Head deck (A) ASSY and Head deck (B) ASSY.
When replacing the parts, refer to the following figure, and use the
appropriate part.
408
Parts with “P” mark: 230PWR1
Parts without “P” mark: 230AWR1

408

407

406
404

HP101
403

407

HRPE101 403 405

406
404
405

409

402

402

401

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
401 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 408 3-016-567-02 SPRING (CASSETTE), LEAF
402 3-911-116-21 RIVET, PUSH * 409 A-2007-731-A AUDIO BOARD, COMPLETE
403 3-016-574-01 SPRING (HEAD), TENSION HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR1)(*NOTE)
404 X-3374-156-2 PINCH LEVER (REV) ASSY
405 X-3374-155-2 PINCH LEVER (FWD) ASSY HP101 A-2056-683-A DECK (A) ASSY, HEAD (230PWR1)(*NOTE)
HRPE101 A-2056-682-A DECK (B) ASSY, HEAD (230AWR1)(*NOTE)
406 3-016-564-01 BASE (PINCH LEVER FWD) HRPE101 A-2056-684-A DECK (B) ASSY, HEAD (230PWR1)(*NOTE)
407 3-016-565-01 BASE (PINCH LEVER REV)

– 105 –
Downloaded from www.Manualslib.com manuals search engine
 9-8. TC MECHANISM SECTION 2
(TCM230AWR1
TCM230PWR1)
*NOTE: Two types of parts which are not interchangeable are available
for the mechanical block assembly. When replacing the parts,
refer to the following figure, and use the appropriate part.

*NOTE: Two types of parts which are not interchangeable are available
for the mechanical block assembly. When replacing the parts,
refer to the following figure, and use the appropriate part.

Parts with “P” mark: 230PWR1

Parts without “P” mark: 230AWR1

461
451

#7

462
459

460 463
458
455 #10
#12

#10 #10
#11

460
452 454
456 #10
459
458

455
452
M1
456
457
453

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 451 X-3374-214-1 CASSIS ASSY, MAIN 459 A-2004-629-A MECHANICAL BLOCK ASSY (230AWR1)(*NOTE)
452 3-016-570-01 BELT (CAPSTAN) 459 A-2004-630-A MECHANICAL BLOCK ASSY (230PWR1)(*NOTE)
453 3-016-569-01 BELT (TENSION) 460 3-016-566-01 SLIDER, REVERSE
454 3-017-360-01 BRACKET (MOTOR)
455 X-3374-234-1 FLYWHEEL (FWD) ASSY * 461 A-2007-732-A LEAF SW BOARD, COMPLETE
462 3-016-575-01 SPRING, TORSION
456 X-3374-235-1 FLYWHEEL (REV) ASSY 463 3-019-208-01 WASHER, STOPPER
457 X-3374-238-1 PULLEY ASSY, TENSION M1 A-2004-628-A MOTOR ASSY, CAPSTAN
458 3-024-405-01 BELT (FR)

– 106 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 10
ELECTRICAL PARTS LIST AUDIO

Note:

The components identified by • Due to standardization, replacements in the parts list • SEMICONDUCTORS
mark ! or dotted line with mark may be different from the parts specified in the In each case, u: µ , for example:
! are critical for safety. diagrams or the components used on the set. uA...: µ A..., uPA...: µ PA..., uPB...: µ PB...,
Replace only with part number • -XX, -X mean standardized parts, so they may have uPC...: µ PC..., uPD...: µ PD...
specified. some difference from the original one. • COILS
• Items marked “*” are not stocked since they are uH : µ H
seldom required for routine service. Some delay • Abbreviation
When indicating parts by reference should be anticipated when ordering these items. EA : Saudi Arabia model
number, please include the board • RESISTORS HK : Hong Kong model
name. All resistors are in ohms SP : Singapore model
METAL: Metal-film resistor MY : Malaysia model
* Note METAL OXIDE: Metal Oxide-film resistor TW : Taiwan model
When replacing IC502, refer to “IC502 of F : nonflammable IA : Indonesian model
Video Board” in “Service Note” (page 13). • CAPACITORS
uF : µ F

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-2007-731-A AUDIO BOARD, COMPLETE < IC >
**********************
IC601 8-759-111-44 IC UPC4570C-1
< CAPACITOR > IC602 8-759-143-54 IC UPC1330HA
IC611 8-759-111-44 IC UPC4570C-1
C301 1-162-289-31 CERAMIC 390PF 10% 50V
C302 1-126-968-11 ELECT 100uF 20% 6.3V < COIL >
C303 1-162-282-31 CERAMIC 100PF 10% 50V
C304 1-130-483-00 MYLAR 0.01uF 5% 50V L331 1-410-780-11 INDUCTOR 27mH
C305 1-107-715-11 ELECT 22uF 20% 16V L431 1-410-780-11 INDUCTOR 27mH
L601 1-414-193-41 INDUCTOR, MICRO 22uH
C311 1-162-289-31 CERAMIC 390PF 10% 50V L602 1-414-193-41 INDUCTOR, MICRO 22uH
C313 1-162-282-31 CERAMIC 100PF 10% 50V
C314 1-130-487-00 MYLAR 0.022uF 5% 50V < TRANSISTOR >
C315 1-126-233-11 ELECT 22uF 20% 50V
C331 1-137-427-11 FILM 120PF 5% 50V Q621 8-729-142-46 TRANSISTOR 2SC2001-LK
Q622 8-729-142-46 TRANSISTOR 2SC2001-LK
C332 1-162-288-31 CERAMIC 330PF 10% 50V Q623 8-729-801-93 TRANSISTOR 2SD1387
C333 1-162-209-31 CERAMIC 27PF 5% 50V
C401 1-162-289-31 CERAMIC 390PF 10% 50V < RESISTOR >
C402 1-126-968-11 ELECT 100uF 20% 6.3V
C403 1-162-282-31 CERAMIC 100PF 10% 50V R301 1-247-881-00 CARBON 120K 5% 1/4W
R302 1-249-409-11 CARBON 220 5% 1/4W F
C404 1-130-483-00 MYLAR 0.01uF 5% 50V R303 1-249-433-11 CARBON 22K 5% 1/4W
C405 1-107-715-11 ELECT 22uF 20% 16V R304 1-247-889-00 CARBON 270K 5% 1/4W
C411 1-162-289-31 CERAMIC 390PF 10% 50V R305 1-247-858-11 CARBON 13K 5% 1/4W
C413 1-162-282-31 CERAMIC 100PF 10% 50V
C414 1-130-487-00 MYLAR 0.022uF 5% 50V R311 1-247-881-00 CARBON 120K 5% 1/4W
R312 1-247-807-31 CARBON 100 5% 1/4W
C415 1-126-233-11 ELECT 22uF 20% 50V R314 1-247-882-11 CARBON 130K 5% 1/4W
C431 1-137-427-11 FILM 120PF 5% 50V R315 1-247-850-11 CARBON 6.2K 5% 1/4W
C432 1-162-288-31 CERAMIC 330PF 10% 50V R331 1-249-430-11 CARBON 12K 5% 1/4W
C433 1-162-209-31 CERAMIC 27PF 5% 50V
C601 1-104-396-11 ELECT 10uF 20% 16V R401 1-247-881-00 CARBON 120K 5% 1/4W
R402 1-249-409-11 CARBON 220 5% 1/4W F
C602 1-104-396-11 ELECT 10uF 20% 16V R403 1-249-433-11 CARBON 22K 5% 1/4W
C611 1-104-396-11 ELECT 10uF 20% 16V R404 1-247-889-00 CARBON 270K 5% 1/4W
C612 1-104-396-11 ELECT 10uF 20% 16V R405 1-247-858-11 CARBON 13K 5% 1/4W
C621 1-137-150-11 FILM 0.01uF 5% 100V
C622 1-126-961-11 ELECT 2.2uF 20% 50V R411 1-247-881-00 CARBON 120K 5% 1/4W
R412 1-247-807-31 CARBON 100 5% 1/4W
C623 1-136-155-00 FILM 0.015uF 5% 50V R414 1-247-882-11 CARBON 130K 5% 1/4W
C624 1-130-481-00 MYLAR 0.0068uF 5% 50V R415 1-247-850-11 CARBON 6.2K 5% 1/4W
C625 1-130-481-00 MYLAR 0.0068uF 5% 50V R431 1-249-430-11 CARBON 12K 5% 1/4W
C627 1-124-903-11 ELECT 1uF 20% 50V
C628 1-136-153-00 FILM 0.01uF 5% 50V R601 1-249-409-11 CARBON 220 5% 1/4W F
R602 1-249-409-11 CARBON 220 5% 1/4W F
C642 1-104-664-11 ELECT 47uF 20% 16V R608 1-249-409-11 CARBON 220 5% 1/4W F
R609 1-249-433-11 CARBON 22K 5% 1/4W
< CONNECTOR > R611 1-249-409-11 CARBON 220 5% 1/4W F

CN601 1-695-338-11 PIN, CONNECTOR (PC BOARD) 15P R612 1-249-409-11 CARBON 220 5% 1/4W F

– 107 –
Downloaded from www.Manualslib.com manuals search engine
 AUDIO BD

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
!R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F < CONNECTOR >
!R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
R623 1-249-432-11 CARBON 18K 5% 1/4W CN101 1-770-706-11 CONNECTOR, FFC/FPC 23P
R624 1-249-432-11 CARBON 18K 5% 1/4W CN102 1-770-425-11 CONNECTOR, FFC/FPC 16P

R625 1-249-429-11 CARBON 10K 5% 1/4W < IC >

< VARIABLE RESISTOR > IC101 8-752-369-78 IC CXD2545Q

IC102 8-759-455-91 IC BA6392FP
RV301 1-238-598-11 RES, ADJ, CARBON 2.2K IC103 8-752-072-45 IC CXA1821M-T6
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K IC104 8-759-271-86 IC TC7SH04FU
RV341 1-241-768-11 RES, ADJ, CARBON 220K
RV401 1-238-598-11 RES, ADJ, CARBON 2.2K < TRANSISTOR >
RV411 1-238-598-11 RES, ADJ, CARBON 2.2K
Q101 8-729-010-08 TRANSISTOR MSB710-R
RV441 1-241-768-11 RES, ADJ, CARBON 220K Q102 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q103 8-729-120-28 TRANSISTOR 2SC1623-L5L6
< TRANSFORMER >
< RESISTOR >
T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION
R101 1-216-077-00 METAL CHIP 15K 5% 1/10W
************************************************************ R102 1-216-097-91 RES,CHIP 100K 5% 1/10W
R103 1-216-077-00 METAL CHIP 15K 5% 1/10W
* A-4699-697-A BD BOARD, COMPLETE R104 1-216-085-00 METAL CHIP 33K 5% 1/10W
****************** R105 1-216-097-91 RES,CHIP 100K 5% 1/10W

< CAPACITOR > R106 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R107 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
C101 1-163-005-11 CERAMIC CHIP 470PF 10% 50V R108 1-216-073-00 METAL CHIP 10K 5% 1/10W
C102 1-163-038-91 CERAMIC CHIP 0.1uF 25V R109 1-216-121-91 RES,CHIP 1M 5% 1/10W
C103 1-163-005-11 CERAMIC CHIP 470PF 10% 50V R110 1-216-025-91 RES,CHIP 100 5% 1/10W
C105 1-104-913-11 TANTAL. CHIP 10uF 20% 16V
C106 1-164-346-11 CERAMIC CHIP 1uF 16V R112 1-216-049-91 RES,CHIP 1K 5% 1/10W
R123 1-216-073-00 METAL CHIP 10K 5% 1/10W
C107 1-164-346-11 CERAMIC CHIP 1uF 16V R124 1-216-097-91 RES,CHIP 100K 5% 1/10W
C108 1-163-035-00 CERAMIC CHIP 0.047uF 50V R125 1-216-033-00 METAL CHIP 220 5% 1/10W
C109 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V R126 1-216-033-00 METAL CHIP 220 5% 1/10W
C110 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C111 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R127 1-216-033-00 METAL CHIP 220 5% 1/10W
R131 1-216-037-00 METAL CHIP 330 5% 1/10W
C112 1-163-038-91 CERAMIC CHIP 0.1uF 25V R134 1-216-049-91 RES,CHIP 1K 5% 1/10W
C113 1-163-038-91 CERAMIC CHIP 0.1uF 25V R141 1-216-089-91 RES,CHIP 47K 5% 1/10W
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V R142 1-216-081-00 METAL CHIP 22K 5% 1/10W
C116 1-126-607-11 ELECT CHIP 47uF 20% 4V
C117 1-126-209-11 ELECT CHIP 100uF 20% 4V R143 1-216-103-00 METAL CHIP 180K 5% 1/10W
R144 1-216-103-00 METAL CHIP 180K 5% 1/10W
C118 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V R146 1-216-073-00 METAL CHIP 10K 5% 1/10W
C119 1-163-091-00 CERAMIC CHIP 8PF 50V R147 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
C120 1-163-038-91 CERAMIC CHIP 0.1uF 25V R148 1-216-001-00 METAL CHIP 10 5% 1/10W
C121 1-163-231-11 CERAMIC CHIP 15PF 5% 50V
C123 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V R149 1-216-003-11 RES,CHIP 12 5% 1/10W
R150 1-216-025-91 RES,CHIP 100 5% 1/10W
C124 1-164-005-11 CERAMIC CHIP 0.47uF 25V R151 1-216-025-91 RES,CHIP 100 5% 1/10W
C125 1-104-913-11 TANTAL. CHIP 10uF 20% 16V R152 1-216-073-00 METAL CHIP 10K 5% 1/10W
C140 1-163-038-91 CERAMIC CHIP 0.1uF 25V R153 1-216-073-00 METAL CHIP 10K 5% 1/10W
C141 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C151 1-163-237-11 CERAMIC CHIP 27PF 5% 50V R154 1-216-025-91 RES,CHIP 100 5% 1/10W
R155 1-216-025-91 RES,CHIP 100 5% 1/10W
C153 1-163-038-91 CERAMIC CHIP 0.1uF 25V R156 1-216-025-91 RES,CHIP 100 5% 1/10W
C154 1-164-336-11 CERAMIC CHIP 0.33uF 25V R158 1-216-109-00 METAL CHIP 330K 5% 1/10W
C156 1-163-237-11 CERAMIC CHIP 27PF 5% 50V R159 1-216-097-91 RES,CHIP 100K 5% 1/10W
C157 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V R160 1-216-295-91 SHORT 0
R161 1-216-308-00 METAL CHIP 4.7 5% 1/10W
C161 1-163-038-91 CERAMIC CHIP 0.1uF 25V R162 1-216-101-00 METAL CHIP 150K 5% 1/10W
C162 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V R171 1-216-025-91 RES,CHIP 100 5% 1/10W
R172 1-216-025-91 RES,CHIP 100 5% 1/10W

R173 1-216-025-91 RES,CHIP 100 5% 1/10W

The components identified by mark ! or dotted

line with mark ! are critical for safety.
– 108 – Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
 BD CD SW CONNECTOR CONT COM

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R175 1-216-025-91 RES,CHIP 100 5% 1/10W * 1-658-575-11 CONNECTOR BOARD
R176 1-216-073-00 METAL CHIP 10K 5% 1/10W ****************
R177 1-216-073-00 METAL CHIP 10K 5% 1/10W
R178 1-216-073-00 METAL CHIP 10K 5% 1/10W < CONNECTOR >

R179 1-216-025-91 RES,CHIP 100 5% 1/10W * CN701 1-568-946-11 PIN, CONNECTOR 8P

CN702 1-750-413-11 CONNECTOR, FFC/FPC 8P
< SWITCH >
< TRANSISTOR >
S101 1-572-085-11 SWITCH, LEAF (LIMIT)
Q701 8-729-900-80 TRANSISTOR DTC114ES
**************************************************************
< RESISTOR >
* 1-668-268-11 CD SW BOARD
*********** R703 1-249-435-11 CARBON 33K 5% 1/4W
R704 1-249-429-11 CARBON 10K 5% 1/4W
< DIODE > R705 1-249-417-11 CARBON 1K 5% 1/4W F

D631 8-719-056-13 DIODE SML79423C-TP15 (DISC 1) ************************************************************

D632 8-719-056-13 DIODE SML79423C-TP15 (DISC 2)
D633 8-719-056-13 DIODE SML79423C-TP15 (DISC 3) * A-4407-476-A CONT COM BOARD, COMPLETE
*************************
< JUMPER RESISTOR >
< CAPACITOR >
JW901 1-216-296-91 SHORT 0
JW902 1-216-295-91 SHORT 0 C627 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C628 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
< TRANSISTOR > C629 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C630 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
Q613 8-729-027-60 TRANSISTOR DTC144TKA-T146
Q614 8-729-027-60 TRANSISTOR DTC144TKA-T146 < CONNECTOR >
Q615 8-729-027-60 TRANSISTOR DTC144TKA-T146
* CN608 1-568-862-11 SOCKET, CONNECTOR 19P
< RESISTOR >
< DIODE >
R656 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R657 1-216-059-00 METAL CHIP 2.7K 5% 1/10W D610 8-719-063-93 DIODE SLR325VC-N-T32 (ENTER/NEXT)
R658 1-216-063-91 METAL CHIP 3.9K 5% 1/10W D612 8-719-057-97 DIODE SEL5923A-TP15 (GROOVE)
R659 1-216-067-00 METAL CHIP 5.6K 5% 1/10W D613 8-719-063-93 DIODE SLR325VC-N-T32 (JOG)
R660 1-216-071-00 RES,CHIP 8.2K 5% 1/10W D614 8-719-064-65 DIODE SELU5723C-TP15 (DJ MIX)
D615 8-719-064-65 DIODE SELU5723C-TP15 (DJ MIX)
R691 1-216-027-00 METAL CHIP 120 5% 1/10W
R692 1-216-027-00 METAL CHIP 120 5% 1/10W D616 8-719-063-93 DIODE SLR325VC-N-T32 (NON-STOP)
R693 1-216-027-00 METAL CHIP 120 5% 1/10W D617 8-719-057-97 DIODE SEL5923A-TP15 (– 0)
R694 1-216-027-00 METAL CHIP 120 5% 1/10W D618 8-719-057-97 DIODE SEL5923A-TP15 (+ ))
R695 1-216-027-00 METAL CHIP 120 5% 1/10W D801 8-719-057-97 DIODE SEL5923A-TP15 (ON/OFF)
D802 8-719-057-97 DIODE SEL5923A-TP15 (JAM)
R696 1-216-027-00 METAL CHIP 120 5% 1/10W
D803 8-719-056-13 DIODE SML79423C-TP15 (AUTO BPM)
< SWITCH >
< TRANSISTOR >
S637 1-762-875-21 SWITCH, KEYBOARD (1/u)
S638 1-762-875-21 SWITCH, KEYBOARD (DISC 1) Q604 8-729-027-60 TRANSISTOR DTC144TKA-T146
S639 1-762-875-21 SWITCH, KEYBOARD (DISC 2) Q854 8-729-027-23 TRANSISTOR DTA114EKA-T146
S640 1-762-875-21 SWITCH, KEYBOARD (DISC 3) Q855 8-729-027-23 TRANSISTOR DTA114EKA-T146
S641 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)
< RESISTOR >
S642 1-762-875-21 SWITCH, KEYBOARD (§)
R637 1-216-039-00 METAL CHIP 390 5% 1/10W
************************************************************** R638 1-216-041-00 METAL CHIP 470 5% 1/10W
R639 1-216-045-00 METAL CHIP 680 5% 1/10W
R640 1-216-047-91 RES,CHIP 820 5% 1/10W
R641 1-216-051-00 METAL CHIP 1.2K 5% 1/10W

R642 1-216-053-00 METAL CHIP 1.5K 5% 1/10W

R643 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R644 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R645 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R646 1-216-067-00 METAL CHIP 5.6K 5% 1/10W

– 109 –
Downloaded from www.Manualslib.com manuals search engine
 CONT COM DECO HP LEAF SW

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R647 1-216-071-00 METAL CHIP 8.2K 5% 1/10W D655 8-719-033-06 DIODE SEL5920A (RIGHT)
R648 1-216-075-00 METAL CHIP 12K 5% 1/10W D656 8-719-033-06 DIODE SEL5920A (RIGHT)
R666 1-216-037-00 METAL CHIP 330 5% 1/10W
R667 1-216-029-00 METAL CHIP 150 5% 1/10W < TRANSISTOR >
R668 1-216-027-00 METAL CHIP 120 5% 1/10W
Q856 8-729-027-60 TRANSISTOR DTC144TKA-T146
R669 1-216-019-00 METAL CHIP 56 5% 1/10W Q857 8-729-027-60 TRANSISTOR DTC144TKA-T146
R670 1-216-037-00 METAL CHIP 330 5% 1/10W
R671 1-216-031-00 METAL CHIP 180 5% 1/10W < RESISTOR >
R811 1-216-029-00 METAL CHIP 150 5% 1/10W
R812 1-216-029-00 METAL CHIP 150 5% 1/10W R706 1-216-019-00 METAL CHIP 56 5% 1/10W
R707 1-216-019-00 METAL CHIP 56 5% 1/10W
R813 1-216-029-00 METAL CHIP 150 5% 1/10W R708 1-216-041-00 METAL CHIP 470 5% 1/10W
R814 1-216-029-00 METAL CHIP 150 5% 1/10W R709 1-216-027-00 METAL CHIP 120 5% 1/10W
R821 1-216-039-00 METAL CHIP 390 5% 1/10W R710 1-216-027-00 METAL CHIP 120 5% 1/10W
R822 1-216-041-00 METAL CHIP 470 5% 1/10W
R823 1-216-045-00 METAL CHIP 680 5% 1/10W **************************************************************

R831 1-216-039-00 METAL CHIP 390 5% 1/10W * 1-668-271-11 HP BOARD

R832 1-216-041-00 METAL CHIP 470 5% 1/10W ********
R833 1-216-045-00 METAL CHIP 680 5% 1/10W
< CAPACITOR >
< SWITCH >
C790 1-163-038-91 CERAMIC CHIP 0.1uF 25V
S601 1-473-534-11 ENCODER, ROTARY (JOG) C791 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
S602 1-473-392-11 ENCODER, ROTARY (VOLUME) C792 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
S617 1-762-875-21 SWITCH, KEYBOARD (CD LOOP)
S618 1-762-875-21 SWITCH, KEYBOARD (CD FLASH) < CONNECTOR >
S619 1-762-875-21 SWITCH, KEYBOARD (CD NON-STOP)
CN752 1-506-469-11 PIN, CONNECTOR 4P
S621 1-762-875-21 SWITCH, KEYBOARD (– 0)
S622 1-762-875-21 SWITCH, KEYBOARD (ENTER/NEXT) < GROUND PLATE >
S623 1-762-875-21 SWITCH, KEYBOARD (+ ))
S624 1-762-875-21 SWITCH, KEYBOARD (DBFB) * EP751 1-537-738-21 TERMINAL, EARTH
S625 1-762-875-21 SWITCH, KEYBOARD (GROOVE)
< JACK >
S626 1-762-875-21 SWITCH, KEYBOARD (ACTIVE)
S627 1-762-875-21 SWITCH, KEYBOARD (SELECT) J755 1-785-200-11 JACK (LARGE TYPE)(PHONES)
S628 1-762-875-21 SWITCH, KEYBOARD (RETURN)
S629 1-762-875-21 SWITCH, KEYBOARD (PREV) **************************************************************
S630 1-762-875-21 SWITCH, KEYBOARD (NEXT)
* A-2007-732-A LEAF SW BOARD, COMPLETE
S801 1-762-875-21 SWITCH, KEYBOARD (PAD-B) ************************
S802 1-762-875-21 SWITCH, KEYBOARD (BEAT LEVEL)
S803 1-762-875-21 SWITCH, KEYBOARD (JAM-BEAT) < CAPACITOR >
S804 1-762-875-21 SWITCH, KEYBOARD (AUTO BPM)
S805 1-762-875-21 SWITCH, KEYBOARD (PAD-A) C1001 1-128-124-11 ELECT 33uF 20% 10V

S806 1-762-875-21 SWITCH, KEYBOARD (ON/OFF-BEAT) < CONNECTOR >

S807 1-762-875-21 SWITCH, KEYBOARD (SELECT-BEAT)
S808 1-762-875-21 SWITCH, KEYBOARD (SPEED-BEAT) CN1001 1-568-860-11 SOCKET, CONNECTOR 17P
CN1001 1-784-459-11 CONNECTOR, FFC/FPC 17P
< CONNECTOR >
< DIODE >
W601 1-775-377-61 LEAD (WITH CONNECTOR)
D1001 8-719-911-19 DIODE 1SS119
************************************************************** D1002 8-719-911-19 DIODE 1SS119

* 1-668-269-11 DECO BOARD < CONNECTOR >

**********
* DM1001 1-784-581-11 HOLDER, CABLE (2.5MM PITCH) 4P
< DIODE >
< IC >
D640 8-719-063-93 DIODE SLR325VC-N-T32 (CENTER)
D641 8-719-032-86 DIODE SEL5420E (LEFT) IC1001 8-749-014-38 IC PHOTO INTERRUPTER SG-264
D642 8-719-032-86 DIODE SEL5420E (LEFT) IC1002 8-749-014-38 IC PHOTO INTERRUPTER SG-264
D643 8-719-032-86 DIODE SEL5420E (LEFT)
D644 8-719-033-06 DIODE SEL5920A (CENTER)

– 110 –
Downloaded from www.Manualslib.com manuals search engine
 LEAF SW MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< TRANSISTOR > C133 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C134 1-163-038-91 CERAMIC CHIP 0.1uF 25V
Q1001 8-729-029-56 TRANSISTOR DTA144ESA C135 1-126-964-11 ELECT 10uF 20% 50V
Q1001 8-729-900-65 TRANSISTOR DTA144ES C136 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C137 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< RESISTOR >
C141 1-109-953-11 ELECT 2.2uF 20% 50V
R907 1-247-879-11 CARBON 100K 5% 1/4W C151 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
R1001 1-249-409-11 CARBON 220 5% 1/4W F C152 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
R1002 1-249-409-11 CARBON 220 5% 1/4W F C153 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
R1003 1-249-414-11 CARBON 560 5% 1/4W F C154 1-216-295-91 SHORT 0
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W
C161 1-137-195-11 FILM 0.56uF 5% 50V
R1005 1-247-818-11 CARBON 300 5% 1/4W C162 1-163-986-00 CERAMIC CHIP 0.027uF 10% 25V
R1006 1-247-864-11 CARBON 24K 5% 1/4W C163 1-136-167-00 FILM 0.15uF 5% 50V
R1007 1-247-856-00 CARBON 11K 5% 1/4W C164 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V
R1008 1-249-417-11 CARBON 1K 5% 1/4W F C165 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V

< VARIABLE RESISTOR > C166 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
C167 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
RV1001 1-241-785-11 RES, ADJ, CARBON 10K C168 1-163-003-11 CERAMIC CHIP 330PF 10% 50V
RV1002 1-241-785-11 RES, ADJ, CARBON 10K C169 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C170 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
< SWITCH >
C171 1-126-964-11 ELECT 10uF 20% 50V
S1001 1-570-953-11 SWITCH, PUSH (1 KEY) (A PLAY) C172 1-163-006-11 CERAMIC CHIP 560PF 10% 50V
S1002 1-570-953-11 SWITCH, PUSH (1 KEY) (B PLAY) C173 1-136-169-00 FILM 0.22uF 5% 50V
S1003 1-771-333-11 SWITCH, LEAF (A HALF) C174 1-136-169-00 FILM 0.22uF 5% 50V
S1004 1-771-205-11 SWITCH, LEAF (A 120/70) C175 1-126-964-11 ELECT 10uF 20% 50V
S1005 1-771-205-11 SWITCH, LEAF (REC A)
C176 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V
S1006 1-771-333-11 SWITCH, LEAF (B HALF) C177 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
S1008 1-771-205-11 SWITCH, LEAF (B 120/70) C191 1-126-964-11 ELECT 10uF 20% 50V
S1009 1-771-205-11 SWITCH, LEAF (REC B) C192 1-163-007-11 CERAMIC CHIP 680PF 10% 50V
C193 1-126-964-11 ELECT 10uF 20% 50V
************************************************************
C194 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
* A-4414-035-A MAIN BOARD, COMPLETE C195 1-163-038-91 CERAMIC CHIP 0.1uF 25V
********************* C196 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C197 1-216-295-91 SHORT 0
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S C301 1-126-960-11 ELECT 1uF 20% 50V

C302 1-130-479-00 MYLAR 0.0047uF 5% 50V

< CAPACITOR > C303 1-136-165-00 FILM 0.1uF 5% 50V
C304 1-136-165-00 FILM 0.1uF 5% 50V
C101 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C305 1-126-964-11 ELECT 10uF 20% 50V
C102 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C306 1-126-960-11 ELECT 1uF 20% 50V
C103 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
C111 1-137-195-11 FILM 0.56uF 5% 50V C307 1-126-959-11 ELECT 0.47uF 20% 50V
C112 1-163-986-00 CERAMIC CHIP 0.027uF 10% 25V C308 1-126-964-11 ELECT 10uF 20% 50V
C309 1-136-173-00 FILM 0.47uF 5% 50V
C113 1-136-167-00 FILM 0.15uF 5% 50V C310 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C114 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V C311 1-126-964-11 ELECT 10uF 20% 50V
C115 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C116 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V C312 1-126-959-11 ELECT 0.47uF 20% 50V
C117 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V C313 1-130-471-00 MYLAR 0.001uF 5% 50V
C314 1-126-964-11 ELECT 10uF 20% 50V
C118 1-163-003-11 CERAMIC CHIP 330PF 10% 50V C315 1-126-963-11 ELECT 4.7uF 20% 50V
C119 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C316 1-104-665-11 ELECT 100uF 20% 10V
C120 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
C121 1-126-964-11 ELECT 10uF 20% 50V C317 1-104-665-11 ELECT 100uF 20% 10V
C122 1-163-006-11 CERAMIC CHIP 560PF 10% 50V C320 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C331 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C123 1-136-169-00 FILM 0.22uF 5% 50V C332 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C124 1-136-169-00 FILM 0.22uF 5% 50V C333 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C125 1-126-964-11 ELECT 10uF 20% 50V
C131 1-104-665-11 ELECT 100uF 20% 10V C334 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C132 1-104-665-11 ELECT 100uF 20% 10V C351 1-126-960-11 ELECT 1uF 20% 50V
C352 1-130-479-00 MYLAR 0.0047uF 5% 50V

– 111 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C353 1-136-165-00 FILM 0.1uF 5% 50V C952 1-136-165-00 FILM 0.1uF 5% 50V
C354 1-136-165-00 FILM 0.1uF 5% 50V C953 1-136-173-00 FILM 0.47uF 5% 50V
C961 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C355 1-126-964-11 ELECT 10uF 20% 50V C991 1-216-295-91 SHORT 0
C356 1-126-960-11 ELECT 1uF 20% 50V
C357 1-126-959-11 ELECT 0.47uF 20% 50V < CONNECTOR >
C358 1-126-964-11 ELECT 10uF 20% 50V
C359 1-136-173-00 FILM 0.47uF 5% 50V * CN101 1-568-832-11 SOCKET, CONNECTOR 13P
CN102 1-784-600-11 SOCKET, CONNECTOR (NON ZIF)15P
C371 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V * CN103 1-568-946-11 PIN, CONNECTOR 8P
C372 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V * CN104 1-568-947-11 PIN, CONNECTOR 9P
C373 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V * CN105 1-568-856-11 SOCKET, CONNECTOR 13P
C374 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C378 1-126-935-11 ELECT 470uF 20% 6.3V CN106 1-568-834-11 SOCKET, CONNECTOR 15P
* CN107 1-568-836-11 SOCKET, CONNECTOR 17P
C382 1-126-925-11 ELECT 470uF 20% 10V * CN301 1-568-449-11 HOUSING, CONNECTOR(PC BOARD) 3P
C383 1-163-038-91 CERAMIC CHIP 0.1uF 25V CN901 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P
C384 1-163-038-91 CERAMIC CHIP 0.1uF 25V CN902 1-770-728-11 CONNECTOR, BOARD TO BOARD 9P
C385 1-126-961-11 ELECT 2.2uF 20% 50V
C386 1-126-961-11 ELECT 2.2uF 20% 50V * CN961 1-564-518-11 PLUG, CONNECTOR 3P

C389 1-126-935-11 ELECT 470uF 20% 6.3V < DIODE >

C390 1-126-935-11 ELECT 470uF 20% 6.3V
C391 1-163-038-91 CERAMIC CHIP 0.1uF 25V D502 8-719-988-62 DIODE 1SS355
C392 1-104-665-11 ELECT 100uF 20% 10V D508 8-719-988-62 DIODE 1SS355
C401 1-163-038-91 CERAMIC CHIP 0.1uF 25V D901 8-719-988-62 DIODE 1SS355
D931 8-719-988-62 DIODE 1SS355
C402 1-163-038-91 CERAMIC CHIP 0.1uF 25V D932 8-719-210-33 DIODE EC10DS2
C403 1-126-964-11 ELECT 10uF 20% 50V
C411 1-163-038-91 CERAMIC CHIP 0.1uF 25V D951 8-719-988-62 DIODE 1SS355
C412 1-163-038-91 CERAMIC CHIP 0.1uF 25V D952 8-719-988-62 DIODE 1SS355
C414 1-126-964-11 ELECT 10uF 20% 50V D953 8-719-988-62 DIODE 1SS355
D954 8-719-988-62 DIODE 1SS355
C415 1-126-964-11 ELECT 10uF 20% 50V D955 8-719-210-33 DIODE EC10DS2
C501 1-126-916-11 ELECT 1000uF 20% 6.3V
C502 1-163-038-91 CERAMIC CHIP 0.1uF 25V D956 8-719-988-62 DIODE 1SS355
C503 1-163-234-11 CERAMIC CHIP 20PF 5% 50V
C504 1-163-235-11 CERAMIC CHIP 22PF 5% 50V < GROUND TERMINAL >

C505 1-163-038-91 CERAMIC CHIP 0.1uF 25V * EPT901 4-870-539-11 PLATE, GROUND
C506 1-104-665-11 ELECT 100uF 20% 10V
C508 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V < COIL >
C901 1-111-235-61 ELECT 10000uF 20% 25V
C902 1-126-943-11 ELECT 2200uF 20% 25V FB381 1-414-234-11 INDUCTOR CHIP 0UH

C903 1-126-964-11 ELECT 10uF 20% 50V < FILTER >

C904 1-126-964-11 ELECT 10uF 20% 50V
C905 1-104-665-11 ELECT 100uF 20% 10V FL131 1-233-289-21 FILTER, EMI (SMD)
C906 1-104-665-11 ELECT 100uF 20% 10V FL501 1-233-289-21 FILTER, EMI (SMD)
C907 1-126-925-11 ELECT 470uF 20% 10V FL502 1-233-289-21 FILTER, EMI (SMD)

C908 1-126-925-11 ELECT 470uF 20% 10V < IC >

C911 1-126-964-11 ELECT 10uF 20% 50V
C912 1-126-768-11 ELECT 2200uF 20% 16V IC111 8-759-495-24 IC M62442FP-TP
C921 1-126-964-11 ELECT 10uF 20% 50V IC191 8-759-636-55 IC M5218AFP
C922 1-126-767-11 ELECT 1000uF 20% 16V IC301 8-759-495-26 IC HA12215
IC391 8-749-923-04 IC TOTX178 (CD DIGITAL OUT OPTICAL)
C931 1-126-964-11 ELECT 10uF 20% 50V IC401 8-759-636-55 IC M5218AFP
C932 1-126-916-11 ELECT 1000uF 20% 6.3V
C933 1-126-916-11 ELECT 1000uF 20% 6.3V IC411 8-759-636-55 IC M5218AFP
C934 1-104-665-11 ELECT 100uF 20% 10V IC501 8-759-546-35 IC uPD780016AYGF014-3BA
C935 1-126-964-11 ELECT 10uF 20% 50V IC901 8-759-450-49 IC BA07T
IC902 8-759-604-90 IC M5F7907L
C936 1-126-916-11 ELECT 1000uF 20% 6.3V IC911 8-759-231-58 IC TA7812S
C937 1-126-925-11 ELECT 470uF 20% 10V
C941 1-126-964-11 ELECT 10uF 20% 50V IC921 8-759-604-38 IC M5F78M10
C942 1-104-665-11 ELECT 100uF 20% 10V IC931 8-759-231-53 IC TA7805S
C951 1-126-967-11 ELECT 47uF 20% 10V IC932 8-759-231-53 IC TA7805S
IC941 8-759-450-49 IC BA07T

– 112 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
IC951 8-759-635-63 IC M51943BSL Q936 8-729-900-36 TRANSISTOR DTC124ES
Q937 8-729-900-36 TRANSISTOR DTC124ES
< JACK > Q951 8-729-119-78 TRANSISTOR 2SC2785-HFE

J101 1-774-411-11 JACK, PIN 6P Q961 8-729-111-29 TRANSISTOR 2SD1616A-K

(VIDEO(AUDIO) IN, MD IN, MD/VIDEO (AUDIO) OUT) Q962 8-729-119-76 TRANSISTOR 2SA1175-HFE
J191 1-774-785-11 JACK, PIN 1P (SUPER WOOFER)
< RESISTOR >
< JUMPER RESISTOR >
R101 1-216-049-91 RES,CHIP 1K 5% 1/10W
JR1 1-216-295-91 SHORT 0 R102 1-216-105-91 RES,CHIP 220K 5% 1/10W
JR2 1-216-295-91 SHORT 0 R103 1-216-049-91 RES,CHIP 1K 5% 1/10W
JR4 1-216-295-91 SHORT 0 R104 1-216-105-91 RES,CHIP 220K 5% 1/10W
JR5 1-216-295-91 SHORT 0 R105 1-216-049-91 RES,CHIP 1K 5% 1/10W

< COIL > R106 1-216-097-91 RES,CHIP 100K 5% 1/10W

R111 1-216-073-00 METAL CHIP 10K 5% 1/10W
L372 1-412-032-11 INDUCTOR CHIP 100uH R112 1-216-121-91 RES,CHIP 1M 5% 1/10W
L391 1-412-032-11 INDUCTOR CHIP 100uH R113 1-216-111-00 METAL CHIP 390K 5% 1/10W
L569 1-412-032-11 INDUCTOR CHIP 100uH R114 1-216-044-00 METAL CHIP 620 5% 1/10W
L570 1-412-032-11 INDUCTOR CHIP 100uH
L572 1-412-032-11 INDUCTOR CHIP 100uH R115 1-216-073-00 METAL CHIP 10K 5% 1/10W
R116 1-216-097-91 RES,CHIP 100K 5% 1/10W
< TRANSISTOR > R117 1-216-073-00 METAL CHIP 10K 5% 1/10W
R118 1-216-089-91 RES,CHIP 47K 5% 1/10W
Q111 8-729-119-78 TRANSISTOR 2SC2785-HFE R119 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q112 8-729-119-78 TRANSISTOR 2SC2785-HFE
Q113 8-729-141-30 TRANSISTOR 2SC3623A-LK R120 1-216-097-91 RES,CHIP 100K 5% 1/10W
Q141 8-729-422-57 TRANSISTOR UN4111 R121 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q142 8-729-900-36 TRANSISTOR DTC124ES R122 1-216-295-91 SHORT 0
R123 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q143 8-729-119-76 TRANSISTOR 2SA1175-HFE R131 1-216-025-91 RES,CHIP 100 5% 1/10W
Q161 8-729-119-78 TRANSISTOR 2SC2785-HFE
Q162 8-729-119-78 TRANSISTOR 2SC2785-HFE R132 1-216-025-91 RES,CHIP 100 5% 1/10W
Q163 8-729-141-30 TRANSISTOR 2SC3623A-LK R133 1-216-025-91 RES,CHIP 100 5% 1/10W
Q191 8-729-141-30 TRANSISTOR 2SC3623A-LK R134 1-216-089-91 RES,CHIP 47K 5% 1/10W
R135 1-216-089-91 RES,CHIP 47K 5% 1/10W
Q331 8-729-118-00 TRANSISTOR 2SB1116-L R136 1-216-089-91 RES,CHIP 47K 5% 1/10W
Q332 8-729-900-80 TRANSISTOR DTC114ES
Q333 8-729-118-00 TRANSISTOR 2SB1116-L R137 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q334 8-729-900-80 TRANSISTOR DTC114ES R138 1-216-089-91 RES,CHIP 47K 5% 1/10W
Q335 8-729-900-80 TRANSISTOR DTC114ES R141 1-216-049-91 RES,CHIP 1K 5% 1/10W
R142 1-216-097-91 RES,CHIP 100K 5% 1/10W
Q336 8-729-116-59 TRANSISTOR 2SB1068-TP R143 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q337 8-729-045-21 TRANSISTOR 2SD1513TP-LK
Q338 8-729-422-57 TRANSISTOR UN4111 R144 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
Q339 8-729-900-80 TRANSISTOR DTC114ES R151 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q340 8-729-166-59 TRANSISTOR 2SB1068-TP R152 1-216-105-91 RES,CHIP 220K 5% 1/10W
R153 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q341 8-729-045-21 TRANSISTOR 2SD1513TP-LK R154 1-216-105-91 RES,CHIP 220K 5% 1/10W
Q342 8-729-422-57 TRANSISTOR UN4111
Q343 8-729-900-80 TRANSISTOR DTC114ES R155 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q411 8-729-141-30 TRANSISTOR 2SC3623A-LK R156 1-216-097-91 RES,CHIP 100K 5% 1/10W
Q901 8-729-040-20 TRANSISTOR RT1P137L-TP R161 1-216-073-00 METAL CHIP 10K 5% 1/10W
R162 1-216-121-91 RES,CHIP 1M 5% 1/10W
Q902 8-729-900-36 TRANSISTOR DTC124ES R163 1-216-111-91 RES,CHIP 390K 5% 1/10W
Q903 8-729-040-19 TRANSISTOR RT1N137L-TP
Q904 8-729-900-63 TRANSISTOR DTA124ES R164 1-216-044-00 METAL CHIP 620 5% 1/10W
Q905 8-729-119-76 TRANSISTOR 2SA1175-HFE R165 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q911 8-729-141-83 TRANSISTOR 2SB1094-LK R166 1-216-097-91 RES,CHIP 100K 5% 1/10W
R167 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q912 8-729-900-36 TRANSISTOR DTC124ES R168 1-216-089-91 RES,CHIP 47K 5% 1/10W
Q913 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q931 8-729-040-20 TRANSISTOR RT1P137L-TP R169 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q932 8-729-900-36 TRANSISTOR DTC124ES R170 1-216-097-91 RES,CHIP 100K 5% 1/10W
Q933 8-729-040-20 TRANSISTOR RT1P137L-TP R171 1-216-073-00 METAL CHIP 10K 5% 1/10W
R172 1-216-295-91 SHORT 0
Q934 8-729-900-63 TRANSISTOR DTA124ES R173 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q935 8-729-141-83 TRANSISTOR 2SB1094-LK

– 113 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R191 1-216-089-91 RES,CHIP 47K 5% 1/10W R371 1-216-049-91 RES,CHIP 1K 5% 1/10W
R192 1-216-089-91 RES,CHIP 47K 5% 1/10W R372 1-216-049-91 RES,CHIP 1K 5% 1/10W
R193 1-216-089-91 RES,CHIP 47K 5% 1/10W
R194 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R381 1-216-025-91 RES,CHIP 100 5% 1/10W
R195 1-216-073-00 METAL CHIP 10K 5% 1/10W R382 1-216-025-91 RES,CHIP 100 5% 1/10W
R383 1-216-085-00 METAL CHIP 33K 5% 1/10W
R196 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R384 1-216-085-00 METAL CHIP 33K 5% 1/10W
R197 1-216-097-91 RES,CHIP 100K 5% 1/10W R385 1-216-085-00 METAL CHIP 33K 5% 1/10W
R198 1-216-049-91 RES,CHIP 1K 5% 1/10W
R199 1-216-073-00 METAL CHIP 10K 5% 1/10W R401 1-216-073-00 METAL CHIP 10K 5% 1/10W
R301 1-216-085-00 METAL CHIP 33K 5% 1/10W R402 1-216-073-00 METAL CHIP 10K 5% 1/10W
R403 1-216-073-00 METAL CHIP 10K 5% 1/10W
R302 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R404 1-216-073-00 METAL CHIP 10K 5% 1/10W
R303 1-216-025-91 RES,CHIP 100 5% 1/10W R411 1-216-073-00 METAL CHIP 10K 5% 1/10W
R304 1-216-025-91 RES,CHIP 100 5% 1/10W
R305 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R412 1-216-049-91 METAL CHIP 1K 5% 1/10W
R306 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R413 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R414 1-216-073-00 METAL CHIP 10K 5% 1/10W
R307 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R416 1-216-073-00 METAL CHIP 10K 5% 1/10W
R308 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R417 1-216-073-00 METAL CHIP 10K 5% 1/10W
R309 1-216-081-00 METAL CHIP 22K 5% 1/10W
R311 1-216-121-91 RES,CHIP 1M 5% 1/10W R418 1-216-073-00 METAL CHIP 10K 5% 1/10W
R312 1-216-102-00 RES,CHIP 160K 5% 1/10W R419 1-216-097-91 RES,CHIP 100K 5% 1/10W
R420 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R313 1-216-097-91 RES,CHIP 100K 5% 1/10W R506 1-216-025-91 RES,CHIP 100 5% 1/10W
R315 1-216-073-00 METAL CHIP 10K 5% 1/10W R507 1-216-025-91 RES,CHIP 100 5% 1/10W
R316 1-216-079-00 METAL CHIP 18K 5% 1/10W
R317 1-216-073-00 METAL CHIP 10K 5% 1/10W R508 1-216-025-91 RES,CHIP 100 5% 1/10W
R318 1-216-073-00 METAL CHIP 10K 5% 1/10W R513 1-216-109-00 METAL CHIP 330K 5% 1/10W
R526 1-216-025-91 RES,CHIP 100 5% 1/10W
R319 1-216-111-00 METAL CHIP 390K 5% 1/10W R527 1-216-025-91 RES,CHIP 100 5% 1/10W
R321 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R555 1-216-025-91 RES,CHIP 100 5% 1/10W
R322 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R324 1-216-094-00 RES,CHIP 75K 5% 1/10W R556 1-216-025-91 RES,CHIP 100 5% 1/10W
R325 1-216-089-91 RES,CHIP 47K 5% 1/10W R557 1-216-025-91 RES,CHIP 100 5% 1/10W
R560 1-216-025-91 RES,CHIP 100 5% 1/10W
R326 1-216-089-91 RES,CHIP 47K 5% 1/10W R561 1-216-025-91 RES,CHIP 100 5% 1/10W
R327 1-216-089-91 RES,CHIP 47K 5% 1/10W R563 1-216-025-91 RES,CHIP 100 5% 1/10W
R328 1-216-094-00 RES,CHIP 75K 5% 1/10W
R329 1-216-049-91 RES,CHIP 1K 5% 1/10W R564 1-216-025-91 RES,CHIP 100 5% 1/10W
R330 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R565 1-216-025-91 RES,CHIP 100 5% 1/10W
R566 1-216-025-91 RES,CHIP 100 5% 1/10W
R331 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R567 1-216-025-91 RES,CHIP 100 5% 1/10W
R332 1-216-045-00 METAL CHIP 680 5% 1/10W R568 1-216-025-91 RES,CHIP 100 5% 1/10W
R333 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R334 1-216-045-00 METAL CHIP 680 5% 1/10W R572 1-216-041-00 RES,CHIP 470 5% 1/10W
R335 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R573 1-216-025-91 RES,CHIP 100 5% 1/10W
R575 1-216-025-91 RES,CHIP 100 5% 1/10W
R336 1-216-089-91 RES,CHIP 47K 5% 1/10W R576 1-216-025-91 RES,CHIP 100 5% 1/10W
R337 1-216-049-91 RES, CHIP 1K 5% 1/10W R578 1-216-025-91 RES,CHIP 100 5% 1/10W
R338 1-216-037-00 METAL CHIP 330 5% 1/10W
R339 1-216-089-91 RES,CHIP 47K 5% 1/10W R579 1-216-025-91 RES,CHIP 100 5% 1/10W
R340 1-216-089-91 RES,CHIP 47K 5% 1/10W R580 1-216-025-91 RES,CHIP 100 5% 1/10W
R581 1-216-025-91 RES,CHIP 100 5% 1/10W
R341 1-216-037-00 METAL CHIP 330 5% 1/10W R595 1-216-025-91 RES,CHIP 100 5% 1/10W
R342 1-216-089-91 RES,CHIP 47K 5% 1/10W R596 1-216-025-91 RES,CHIP 100 5% 1/10W
R343 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R344 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R597 1-216-025-91 RES,CHIP 100 5% 1/10W
R351 1-216-085-00 METAL CHIP 33K 5% 1/10W R598 1-216-025-91 RES,CHIP 100 5% 1/10W
R705 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R352 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R729 1-216-295-91 SHORT 0
R353 1-216-025-91 RES,CHIP 100 5% 1/10W R731 1-216-073-00 METAL CHIP 10K 5% 1/10W
R354 1-216-025-91 RES,CHIP 100 5% 1/10W
R355 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R769 1-216-073-00 METAL CHIP 10K 5% 1/10W
R356 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R770 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R778 1-216-089-91 RES,CHIP 47K 5% 1/10W
R357 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R779 1-216-089-91 RES,CHIP 47K 5% 1/10W
R358 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R780 1-216-089-91 RES,CHIP 47K 5% 1/10W
R359 1-216-085-00 METAL CHIP 33K 5% 1/10W

– 114 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN MIC

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R781 1-216-089-91 RES,CHIP 47K 5% 1/10W C776 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
R800 1-216-065-91 RES,CHIP 4.7K 5% 1/10W C777 1-164-492-11 CERAMIC CHIP 0.15uF 10% 16V
R901 1-216-065-91 RES,CHIP 4.7K 5% 1/10W C778 1-126-960-11 ELECT 1uF 20% 50V
R902 1-216-081-00 METAL CHIP 22K 5% 1/10W C779 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
R911 1-216-089-91 RES,CHIP 47K 5% 1/10W C780 1-126-961-11 ELECT 2.2uF 20% 50V

R912 1-216-065-91 RES,CHIP 4.7K 5% 1/10W C782 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
R931 1-216-049-91 RES,CHIP 1K 5% 1/10W
R932 1-216-065-91 RES,CHIP 4.7K 5% 1/10W < DIODE >
R933 1-216-041-00 METAL CHIP 4.70 5% 1/10W
R951 1-216-049-91 RES,CHIP 1K 5% 1/10W D751 8-719-210-33 DIODE EC10DS2
D752 8-719-210-33 DIODE EC10DS2
R952 1-216-065-91 RES,CHIP 4.7K 5% 1/10W D753 8-719-210-33 DIODE EC10DS2
R953 1-216-025-91 RES,CHIP 100 5% 1/10W
R954 1-216-089-91 RES,CHIP 47K 5% 1/10W < FILTER >
R955 1-216-089-91 RES,CHIP 47K 5% 1/10W
R956 1-216-073-00 METAL CHIP 10K 5% 1/10W FL751 1-233-289-21 FILTER, CHIP EMI

R961 1-216-057-00 METAL CHIP 2.2K 5% 1/10W < IC >

R962 1-216-079-00 METAL CHIP 18K 5% 1/10W
R963 1-216-065-91 RES,CHIP 4.7K 5% 1/10W IC750 8-759-636-55 IC M5218AFP
IC751 8-759-496-41 IC M6585DFP-E1
< VARIABLE RESISTOR >
< JACK >
RV301 1-241-764-11 RES, ADJ, CARBON 10K
RV351 1-241-764-11 RES, ADJ, CARBON 10K J750 1-785-200-11 JACK (LARGE TYPE) (MIC 2)
J751 1-785-200-11 JACK (LARGE TYPE) (MIC 1)
< VIBRATOR >
< COIL >
X501 1-579-233-11 VIBRATOR, CERAMIC (5MHz)
X502 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) L751 1-412-032-11 INDUCTOR CHIP 100uH

************************************************************** < RESISTOR >

* A-4414-041-A MIC BOARD, COMPLETE R750 1-216-073-00 METAL CHIP 10K 5% 1/10W
****************** R751 1-216-049-91 RES,CHIP 1K 5% 1/10W
R752 1-216-097-91 RES,CHIP 100K 5% 1/10W
< CAPACITOR > R753 1-216-049-91 RES,CHIP 1K 5% 1/10W
R754 1-216-089-91 RES, CHIP 47K 5% 1/10W
C750 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C751 1-126-957-11 ELECT 0.22uF 20% 50V R755 1-216-073-00 METAL CHIP 10K 5% 1/10W
C752 1-163-038-91 CERAMIC CHIP 0.1uF 25V R756 1-216-107-00 METAL CHIP 270K 5% 1/10W
C754 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V R757 1-216-025-91 RES,CHIP 100 5% 1/10W
C755 1-126-957-11 ELECT 0.22uF 20% 50V R758 1-216-081-00 METAL CHIP 22K 5% 1/10W
R759 1-216-081-00 METAL CHIP 22K 5% 1/10W
C756 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C757 1-163-133-11 CERAMIC CHIP 220PF 5% 50V R760 1-216-081-00 METAL CHIP 22K 5% 1/10W
C758 1-126-964-11 ELECT 10uF 20% 50V R761 1-216-099-00 METAL CHIP 120K 5% 1/10W
C759 1-126-959-11 ELECT 0.47uF 20% 50V R762 1-216-081-00 METAL CHIP 22K 5% 1/10W
C760 1-163-243-11 CERAMIC CHIP 47PF 5% 50V R763 1-216-081-00 METAL CHIP 22K 5% 1/10W
R764 1-216-081-00 METAL CHIP 22K 5% 1/10W
C761 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C762 1-126-961-11 ELECT 2.2uF 20% 50V R765 1-216-089-91 RES,CHIP 47K 5% 1/10W
C764 1-126-964-11 ELECT 10uF 20% 50V R766 1-216-077-00 METAL CHIP 15K 5% 1/10W
C765 1-126-960-11 ELECT 1uF 20% 50V R767 1-216-077-00 METAL CHIP 15K 5% 1/10W
C766 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V R768 1-216-049-91 RES,CHIP 1K 5% 1/10W
R769 1-216-073-00 METAL CHIP 10K 5% 1/10W
C767 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C768 1-136-495-11 FILM 0.068uF 5% 50V < VARIABLE RESISTOR >
C769 1-126-959-11 ELECT 0.47uF 20% 50V
C769 1-136-495-11 FILM 0.068uF 5% 50V RV750 1-225-587-11 RES, VAR 50K (MIC LEVEL)
C770 1-126-959-11 ELECT 0.47uF 20% 50V RV751 1-225-587-11 RES, VAR 50K (ECHO LEVEL)

C771 1-126-967-11 ELECT 47uF 20% 16V **************************************************************

C772 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C773 1-126-967-11 ELECT 47uF 20% 16V
C774 1-136-495-11 FILM 0.068uF 5% 50V
C775 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V

– 115 –
Downloaded from www.Manualslib.com manuals search engine
 MOTOR (SLIDE) MOTOR (TURN) PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-658-578-11 MOTOR (SLIDE) BOARD < CAPACITOR >
*******************
C600 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< CAPACITOR > C601 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C602 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C801 1-162-306-11 CERAMIC 0.01uF 20% 16V C603 1-124-589-11 ELECT 47uF 20% 16V
C804 1-162-306-11 CERAMIC 0.01uF 20% 16V C604 1-126-163-11 ELECT 4.7uF 20% 50V
C805 1-126-964-11 ELECT 10uF 20% 50V
C605 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
< CONNECTOR > C606 1-126-160-11 ELECT 1uF 20% 50V
C607 1-126-160-11 ELECT 1uF 20% 50V
* CN801 1-568-947-11 PIN, CONNECTOR 9P C608 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C609 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< DIODE >
C610 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
D801 8-719-109-89 DIODE RD5.6ESB2 C611 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
D804 8-719-911-19 DIODE 1SS119-25 C612 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
D805 8-719-911-19 DIODE 1SS119-25 C613 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C614 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< IC >
C615 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
IC801 8-759-274-09 IC BA6286N C616 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C617 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< RESISTOR > C618 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C619 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
R801 1-249-401-11 CARBON 47 5% 1/4W F
C620 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< SWITCH > C621 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C625 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
S801 1-762-527-11 SWITCH, ROTARY C626 1-124-589-11 ELECT 47uF 20% 16V
C631 1-126-157-11 ELECT 10uF 20% 16V
************************************************************
C632 1-126-157-11 ELECT 10uF 20% 16V
* 1-658-577-11 MOTOR (TURN) BOARD C633 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
******************* C634 1-126-157-11 ELECT 10uF 20% 16V
C652 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
< CAPACITOR > C801 1-163-038-91 CERAMIC CHIP 0.1uF 25V

C701 1-162-306-11 CERAMIC 0.01uF 20% 16V C802 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C702 1-126-964-11 ELECT 10uF 20% 50V C803 1-124-589-11 ELECT 47uF 20% 16V
C705 1-162-306-11 CERAMIC 0.01uF 20% 16V C804 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C805 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< CONNECTOR > C806 1-126-963-11 ELECT 4.7uF 20% 50V

CN703 1-750-413-11 CONNECTOR, FFC/FPC 8P C807 1-163-017-00 CERAMIC CHIP 4700PF 10% 50V
CN704 1-506-469-11 PIN, CONNECTOR 4P C808 1-163-017-00 CERAMIC CHIP 4700PF 10% 50V
C809 1-126-967-11 ELECT 47uF 20% 50V
< DIODE > C851 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C852 1-126-935-11 ELECT 470uF 20% 6.3V
D701 8-719-109-69 DIODE RD3.6ES-B2
C853 1-126-963-11 ELECT 4.7uF 20% 50V
< IC >
< CONNECTOR >
IC701 8-759-633-65 IC M54641L
* CN601 1-568-832-11 SOCKET, CONNECTOR 13P
< RESISTOR > CN602 1-764-698-11 SOCKET, CONNECTOR 19P
* CN603 1-568-943-11 PIN, CONNECTOR 5P
R706 1-249-411-11 CARBON 330 5% 1/4W CN604 1-506-486-11 PIN, CONNECTOR 7P
R707 1-249-401-11 CARBON 47 5% 1/4W F
< DIODE >
************************************************************
D601 8-719-058-24 DIODE RB501V-40TE-17
* A-4414-042-A PANEL BOARD, COMPLETE D602 8-719-210-33 DIODE EC10DS2
********************* D603 8-719-210-33 DIODE EC10DS2
D620 8-719-063-93 DIODE SLR325VC-N-T32 (EFFECT)
* 4-932-810-31 CUSHION (FL) D621 8-719-056-13 DIODE SML79423C-TP15 (CD ^)
* 4-996-796-11 HOLDER, FL TUBE
D622 8-719-058-03 DIODE SEL5423E-TP15 (9 TAPE B)
D623 8-719-058-03 DIODE SEL5423E-TP15 (( TAPE B)

– 116 –
Downloaded from www.Manualslib.com manuals search engine
 PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D624 8-719-058-03 DIODE SEL5423E-TP15 (9 TAPE A) L851 1-412-031-11 INDUCTOR CHIP 47uH
D625 8-719-058-03 DIODE SEL5423E-TP15 (( TAPE A)
D626 8-719-057-97 DIODE SEL5923A-TP15 (PBC) < FLUORECENT INDICATOR >

D627 8-719-057-97 DIODE SEL5923A-TP15 (PBC OFF) ND601 1-517-731-21 INDICATOR TUBE, FLUORESCENT
D628 8-719-057-97 DIODE SEL5923A-TP15 (VIDEO CD)
D630 8-719-057-97 DIODE SEL5923A-TP15 (SONIC FORMATION) < TRANSISTOR >
D651 8-719-063-93 DIODE SLR325VC-N-T32 (r REC)
D652 8-719-057-97 DIODE SEL5923A-TP15 (P PAUSE) Q601 8-729-118-00 TRANSISTOR 2SB1116-L
Q602 8-729-118-00 TRANSISTOR 2SB1116-L
D804 8-719-988-62 DIODE 1SS355 Q603 8-729-120-28 TRANSISTOR 2SC1623-L5L6
D805 8-719-988-62 DIODE 1SS355 Q607 8-729-027-60 TRANSISTOR DTC144TKA-T146
D806 8-719-988-62 DIODE 1SS355 Q608 8-729-027-60 TRANSISTOR DTC144TKA-T146
D807 8-719-988-62 DIODE 1SS355
Q609 8-729-027-60 TRANSISTOR DTC144TKA-T146
< FILTER > Q610 8-729-027-60 TRANSISTOR DTC144TKA-T146
Q611 8-729-027-60 TRANSISTOR DTC144TKA-T146
FL601 1-233-289-21 FILTER, CHIP EMI Q618 8-729-027-60 TRANSISTOR DTC144TKA-T146
FL602 1-233-289-21 FILTER, CHIP EMI Q701 8-729-120-28 TRANSISTOR 2SC1623-L5L6
FL801 1-233-289-21 FILTER, CHIP EMI
FL802 1-233-289-21 FILTER, CHIP EMI Q702 8-729-120-28 TRANSISTOR 2SC1623-L5L6
FL851 1-233-289-21 FILTER, CHIP EMI Q851 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q958 1-801-900-53 TRANSISTOR DTC114EKA
< IC > Q959 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q960 8-729-027-23 TRANSISTOR DTA114EKA-T146
IC601 8-759-546-36 IC TMP87CM74AF-6731
IC602 8-749-011-22 IC GP1U27X < RESISTOR >
IC603 8-759-495-25 IC BA3833FP-E2
IC801 8-759-496-11 IC TMP87CH48DF-4825 R601 1-216-121-91 RES,CHIP 1M 5% 1/10W
IC851 8-759-498-98 IC MSM6653A-517GS-K R602 1-216-025-91 RES,CHIP 100 5% 1/10W
R604 1-216-073-00 METAL CHIP 10K 5% 1/10W
< JUMPER RESISTOR > R605 1-216-073-00 METAL CHIP 10K 5% 1/10W
R606 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR903 1-216-296-91 SHORT 0
JR904 1-216-296-91 SHORT 0 R607 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR905 1-216-296-91 SHORT 0 R608 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
JR906 1-216-295-91 SHORT 0 R609 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
JR907 1-216-296-91 SHORT 0 R610 1-216-025-91 RES,CHIP 100 5% 1/10W
R611 1-216-025-91 RES,CHIP 100 5% 1/10W
JR908 1-216-296-91 SHORT 0
JR909 1-216-296-91 SHORT 0 R612 1-216-017-91 RES,CHIP 47 5% 1/10W
JR910 1-216-296-91 SHORT 0 R613 1-216-081-00 METAL CHIP 22K 5% 1/10W
JR911 1-216-296-91 SHORT 0 R614 1-216-081-00 METAL CHIP 22K 5% 1/10W
JR912 1-216-295-91 SHORT 0 R616 1-216-097-91 RES,CHIP 100K 5% 1/10W
R618 1-216-089-91 RES,CHIP 47K 5% 1/10W
JR913 1-216-296-91 SHORT 0
JR914 1-216-296-91 SHORT 0 R619 1-216-089-91 RES,CHIP 47K 5% 1/10W
JR915 1-216-296-91 SHORT 0 R621 1-216-075-00 METAL CHIP 12K 5% 1/10W
JR916 1-216-296-91 SHORT 0 R622 1-216-039-00 METAL CHIP 390 5% 1/10W
JR917 1-216-296-91 SHORT 0 R623 1-216-041-00 METAL CHIP 470 5% 1/10W
R624 1-216-045-00 METAL CHIP 680 5% 1/10W
JR918 1-216-296-91 SHORT 0
JR919 1-216-295-91 SHORT 0 R625 1-216-047-91 METAL CHIP 820 5% 1/10W
JR920 1-216-295-91 SHORT 0 R626 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
JR921 1-216-295-91 SHORT 0 R627 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
JR922 1-216-295-91 SHORT 0 R628 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R629 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
JR923 1-216-296-91 SHORT 0
JR924 1-216-296-91 SHORT 0 R630 1-216-063-91 METAL CHIP 3.9K 5% 1/10W
JR925 1-216-295-91 SHORT 0 R631 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
JR926 1-216-295-91 SHORT 0 R632 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
JR927 1-216-295-91 SHORT 0 R633 1-216-075-00 METAL CHIP 12K 5% 1/10W
R636 1-216-075-00 METAL CHIP 12K 5% 1/10W
JR928 1-216-295-91 SHORT 0
R649 1-216-075-00 METAL CHIP 12K 5% 1/10W
< COIL > R650 1-216-039-00 METAL CHIP 390 5% 1/10W
R651 1-216-041-00 METAL CHIP 470 5% 1/10W
L601 1-412-031-11 INDUCTOR CHIP 47uH R652 1-216-045-00 METAL CHIP 680 5% 1/10W
L602 1-412-031-11 INDUCTOR CHIP 47uH R653 1-216-047-91 METAL CHIP 820 5% 1/10W

– 117 –
Downloaded from www.Manualslib.com manuals search engine
 PANEL POWER

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R654 1-216-051-00 METAL CHIP 1.2K 5% 1/10W S611 1-762-875-21 SWITCH, KEYBOARD (EFFECT)
R655 1-216-053-00 METAL CHIP 1.5K 5% 1/10W S612 1-762-875-21 SWITCH, KEYBOARD (DEMO)
R661 1-216-089-91 RES,CHIP 47K 5% 1/10W S613 1-762-875-21 SWITCH, KEYBOARD (TIMER SELECT)
R662 1-216-089-91 RES,CHIP 47K 5% 1/10W
R663 1-216-049-91 RES,CHIP 1K 5% 1/10W S614 1-762-875-21 SWITCH, KEYBOARD (FUNCTION)
S615 1-762-875-21 SWITCH, KEYBOARD (CLOCK/TIMER SET)
R664 1-216-049-91 RES,CHIP 1K 5% 1/10W S616 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)
R665 1-216-089-91 RES,CHIP 47K 5% 1/10W S631 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)
R673 1-216-037-00 METAL CHIP 330 5% 1/10W S632 1-762-875-21 SWITCH, KEYBOARD (CD ^)
R674 1-216-027-00 METAL CHIP 120 5% 1/10W
R675 1-216-027-00 METAL CHIP 120 5% 1/10W S633 1-762-875-21 SWITCH, KEYBOARD (( TAPE B)
S634 1-762-875-21 SWITCH, KEYBOARD (9 TAPE B)
R676 1-216-027-00 METAL CHIP 120 5% 1/10W S635 1-762-875-21 SWITCH, KEYBOARD (( TAPE A)
R677 1-216-027-00 METAL CHIP 120 5% 1/10W S636 1-762-875-21 SWITCH, KEYBOARD (9 TAPE A)
R678 1-216-027-00 METAL CHIP 120 5% 1/10W S652 1-762-875-21 SWITCH, KEYBOARD
R679 1-216-027-00 METAL CHIP 120 5% 1/10W (PLAY MODE, DOLBY NR, TUNER MEMORY)
R680 1-216-029-00 METAL CHIP 150 5% 1/10W
S653 1-762-875-21 SWITCH, KEYBOARD (EDIT, DIRECTION)
R681 1-216-029-00 METAL CHIP 150 5% 1/10W S654 1-762-875-21 SWITCH, KEYBOARD (REPEAT, STEREO/MONO)
R682 1-216-029-00 METAL CHIP 150 5% 1/10W S656 1-762-875-21 SWITCH, KEYBOARD (r REC)
R683 1-216-057-00 METAL CHIP 2.2K 5% 1/10W S657 1-762-875-21 SWITCH, KEYBOARD (P PAUSE)
R684 1-216-057-00 METAL CHIP 2.2K 5% 1/10W S658 1-762-875-21 SWITCH, KEYBOARD (HI-DUB)
R701 1-216-073-00 METAL CHIP 10K 5% 1/10W
S659 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)
R702 1-216-073-00 METAL CHIP 10K 5% 1/10W
R703 1-216-097-91 RES,CHIP 100K 5% 1/10W < VIBRATOR >
R704 1-216-097-91 RES,CHIP 100K 5% 1/10W
R721 1-216-029-00 METAL CHIP 150 5% 1/10W X501 1-579-125-11 VIBRATOR, CERAMIC (8MHz)
R723 1-216-075-00 METAL CHIP 12K 5% 1/10W X601 1-579-125-11 VIBRATOR, CERAMIC (8MHz)
X851 1-767-353-11 VIBRATOR, CERAMIC (4.09MHz)
R724 1-216-039-00 METAL CHIP 390 5% 1/10W
R725 1-216-041-00 METAL CHIP 470 5% 1/10W **************************************************************
R726 1-216-045-00 METAL CHIP 680 5% 1/10W
R727 1-216-047-91 METAL CHIP 820 5% 1/10W * A-4407-260-A POWER BOARD, COMPLETE
R728 1-216-051-00 METAL CHIP 1.2K 5% 1/10W **********************
(SP,MY(Indonesia Product),EA,HK,IA,TW)
R729 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R730 1-216-057-00 METAL CHIP 2.2K 5% 1/10W * A-4407-498-A POWER BOARD, COMPLETE
R731 1-216-059-00 METAL CHIP 2.7K 5% 1/10W **********************
R742 1-216-027-00 METAL CHIP 120 5% 1/10W (MY(Malaysia Product))
R743 1-216-027-00 METAL CHIP 120 5% 1/10W
< CAPACITOR >
R801 1-216-121-91 RES,CHIP 1M 5% 1/10W
R802 1-216-025-91 RES,CHIP 100 5% 1/10W C101 1-130-781-00 FILM 0.22uF 10% 100V
R803 1-216-025-91 RES,CHIP 100 5% 1/10W C102 1-130-781-00 FILM 0.22uF 10% 100V
R804 1-216-025-91 RES,CHIP 100 5% 1/10W C103 1-164-159-21 CERAMIC 0.1uF 50V
R805 1-216-075-00 METAL CHIP 12K 5% 1/10W C104 1-164-159-21 CERAMIC 0.1uF 50V
C105 1-126-943-11 ELECT 2200uF 20% 25V
R806 1-216-075-00 METAL CHIP 12K 5% 1/10W
R807 1-216-085-00 METAL CHIP 33K 5% 1/10W C106 1-162-294-31 CERAMIC 0.001uF 10% 50V
R808 1-216-113-00 METAL CHIP 470K 5% 1/10W C107 1-162-294-31 CERAMIC 0.001uF 10% 50V
R809 1-216-065-91 RES,CHIP 4.7K 5% 1/10W C111 1-126-968-11 ELECT 100uF 20% 50V
R810 1-216-089-91 RES,CHIP 47K 5% 1/10W C112 1-126-968-11 ELECT 100uF 20% 50V
C113 1-162-294-31 CERAMIC 0.001uF 10% 50V
R851 1-216-097-91 RES,CHIP 100K 5% 1/10W
R852 1-216-025-91 RES,CHIP 100 5% 1/10W C114 1-126-967-11 ELECT 47uF 20% 50V
R954 1-216-097-91 RES,CHIP 100K 5% 1/10W C151 1-128-493-11 ELECT 4700uF 20% 71V
C152 1-128-493-11 ELECT 4700uF 20% 71V
R955 1-216-097-91 RES,CHIP 100K 5% 1/10W C201 1-128-582-11 ELECT 10uF 20% 100V
C202 1-162-292-31 CERAMIC 680PF 10% 50V
< SWITCH >
C203 1-162-286-21 CERAMIC 220PF 10% 50V
S604 1-762-875-21 SWITCH, KEYBOARD (SONIC FORMATION) C204 1-126-967-11 ELECT 47uF 20% 50V
S605 1-762-875-21 SWITCH, KEYBOARD (SURROUND) C205 1-126-967-11 ELECT 47uF 20% 50V
S606 1-762-875-21 SWITCH, KEYBOARD (KARAOKE PON/MPX) C206 1-128-560-11 ELECT 22uF 20% 100V
S607 1-762-875-21 SWITCH, KEYBOARD (p) C207 1-130-493-00 MYLAR 0.068uF 5% 50V
S608 1-762-875-21 SWITCH, KEYBOARD (P FILE MEMORY)
C208 1-130-493-00 MYLAR 0.068uF 5% 50V
S609 1-762-875-21 SWITCH, KEYBOARD (GEQ CONTROL) C221 1-162-284-31 CERAMIC 150PF 10% 50V
S610 1-762-875-21 SWITCH, KEYBOARD (FILE SELECT)

– 118 –
Downloaded from www.Manualslib.com manuals search engine
 POWER

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C222 1-162-284-31 CERAMIC 150PF 10% 50V < IC >
C223 1-164-159-21 CERAMIC 0.1uF 50V
C224 1-128-560-11 ELECT 22uF 20% 100V IC201 8-749-921-68 IC STK-4231MK2

C228 1-162-284-31 CERAMIC 150PF 10% 50V < TRANSISTOR >

C251 1-128-582-11 ELECT 10uF 20% 100V
C252 1-162-292-31 CERAMIC 680PF 10% 50V Q111 8-729-118-01 TRANSISTOR 2SB1116-K
C253 1-162-286-21 CERAMIC 220PF 10% 50V Q201 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
C254 1-126-967-11 ELECT 47uF 20% 50V Q251 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q301 8-729-119-76 TRANSISTOR 2SA1175-HFE
C255 1-126-967-11 ELECT 47uF 20% 50V Q302 8-729-119-78 TRANSISTOR 2SC2785-HFE
C256 1-128-560-11 ELECT 22uF 20% 100V
C257 1-130-493-00 MYLAR 0.068uF 5% 50V Q303 8-729-900-36 TRANSISTOR DTC124ES
C258 1-130-493-00 MYLAR 0.068uF 5% 50V Q304 8-729-119-76 TRANSISTOR 2SA1175-HFE
C301 1-126-934-11 ELECT 220uF 20% 10V Q305 8-729-900-36 TRANSISTOR DTC124ES
Q306 8-729-119-78 TRANSISTOR 2SC2785-HFE
C302 1-126-934-11 ELECT 220uF 20% 10V Q307 8-729-119-78 TRANSISTOR 2SC2785-HFE
C303 1-126-961-11 ELECT 2.2uF 20% 50V
C311 1-126-959-11 ELECT 0.47uF 20% 50V Q321 8-729-119-78 TRANSISTOR 2SC2785-HFE
C331 1-126-924-11 ELECT 330uF 20% 10V Q322 8-729-900-36 TRANSISTOR DTC124ES
C401 1-126-963-11 ELECT 4.7uF 20% 50V Q401 8-729-040-20 TRANSISTOR RT1P137L-TP
Q402 8-729-900-80 TRANSISTOR DTC114ES
C412 1-161-494-00 CERAMIC 0.022uF 25V Q403 8-729-040-20 TRANSISTOR RT1P137L-TP
C413 1-161-494-00 CERAMIC 0.022uF 25V
C414 1-161-494-00 CERAMIC 0.022uF 25V Q407 8-729-900-80 TRANSISTOR DTC114ES
C415 1-161-494-00 CERAMIC 0.022uF 25V Q408 8-729-119-78 TRANSISTOR 2SC2785-HFE

< CONNECTOR > < RESISTOR >

CN201 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P R103 1-249-441-11 CARBON 100K 5% 1/4W
CN202 1-770-724-11 CONNECTOR, BOARD TO BOARD 9P ! R111 1-217-637-00 FUSIBLE 1 5% 1/4W F
* CN203 1-573-128-11 PIN, CONNECTOR 5P R112 1-249-417-11 CARBON 1K 5% 1/4W F
R113 1-249-417-11 CARBON 1K 5% 1/4W F
< DIODE > R114 1-247-815-91 CARBON 220 5% 1/4W

D101 8-719-510-68 DIODE D5SBA204101 R115 1-247-815-91 CARBON 220 5% 1/4W

D102 8-719-028-23 DIODE D3SBA20-4101 R116 1-249-425-11 CARBON 4.7K 5% 1/4W F
D103 8-719-200-82 DIODE 11ES2 R201 1-249-417-11 CARBON 1K 5% 1/4W F
D104 8-719-200-82 DIODE 11ES2 R202 1-249-437-11 CARBON 47K 5% 1/4W
D111 8-719-200-82 DIODE 11ES2 R203 1-249-412-11 CARBON 390 5% 1/4W F

D112 8-719-200-82 DIODE 11ES2 R204 1-249-437-11 CARBON 47K 5% 1/4W

D113 8-719-936-50 DIODE HZS33-2LTD R205 1-260-107-11 CARBON 4.7K 5% 1/2W
D114 8-719-109-89 DIODE RD5.6ESB2 R206 1-260-107-11 CARBON 4.7K 5% 1/2W
D201 8-719-991-33 DIODE 1SS133T-77 ! R207 1-212-881-11 FUSIBLE 100 5% 1/4W F
D251 8-719-991-33 DIODE 1SS133T-77 R208 1-220-893-11 METAL 0.22 10% 5W

D301 8-719-991-33 DIODE 1SS133T-77 R209 1-249-417-11 CARBON 1K 5% 1/4W F

D311 8-719-991-33 DIODE 1SS133T-77 R210 1-249-431-11 CARBON 15K 5% 1/4W
D321 8-719-991-33 DIODE 1SS133T-77 R211 1-249-441-11 CARBON 100K 5% 1/4W
D331 8-719-991-33 DIODE 1SS133T-77 R212 1-260-076-11 CARBON 10 5% 1/2W
D332 8-719-991-33 DIODE 1SS133T-77 ! R221 1-217-637-00 FUSIBLE 1 5% 1/4W F

D401 8-719-991-33 DIODE 1SS133T-77 R222 1-260-103-11 CARBON 2.2K 5% 1/2W

D402 8-719-991-33 DIODE 1SS133T-77 R223 1-260-103-11 CARBON 2.2K 5% 1/2W
D404 8-719-991-33 DIODE 1SS133T-77 R224 1-249-425-11 CARBON 4.7K 5% 1/4W F
D405 8-719-991-33 DIODE 1SS133T-77 R251 1-249-417-11 CARBON 1K 5% 1/4W F
D406 8-719-991-33 DIODE 1SS133T-77 R252 1-249-437-11 CARBON 47K 5% 1/4W

D407 8-719-911-19 DIODE 1SS119 R253 1-249-412-11 CARBON 390 5% 1/4W F

D408 8-719-911-19 DIODE 1SS119 R254 1-249-437-11 CARBON 47K 5% 1/4W
R255 1-260-107-11 CARBON 4.7K 5% 1/2W
< GROUND PLATE > R256 1-260-107-11 CARBON 4.7K 5% 1/2W
! R257 1-212-881-11 FUSIBLE 100 5% 1/4W F
* EP101 1-537-738-21 TERMINAL, EARTH
* EP201 1-537-738-21 TERMINAL, EARTH R258 1-220-893-11 METAL 0.22 10% 5W
R259 1-249-417-11 CARBON 1K 5% 1/4W F
R260 1-249-431-11 CARBON 15K 5% 1/4W
R261 1-249-441-11 CARBON 100K 5% 1/4W

The components identified by mark ! or dotted

line with mark ! are critical for safety.
– 119 – Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
 POWER SENSOR TRANSFORMER VIDEO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R262 1-260-076-11 CARBON 10 5% 1/2W < RESISTOR >

R271 1-260-093-11 CARBON 330 5% 1/2W R701 1-249-416-11 CARBON 820 5% 1/4W F
R272 1-260-093-11 CARBON 330 5% 1/2W R702 1-249-407-11 CARBON 150 5% 1/4W F
R273 1-260-093-11 CARBON 330 5% 1/2W
R274 1-260-093-11 CARBON 330 5% 1/2W ************************************************************
R301 1-249-429-11 CARBON 10K 5% 1/4W
* 1-668-274-11 TRANSFORMER BOARD
R302 1-249-425-11 CARBON 4.7K 5% 1/4W F *******************
R303 1-249-429-11 CARBON 10K 5% 1/4W
R304 1-249-429-11 CARBON 10K 5% 1/4W < CONNECTOR >
R305 1-249-425-11 CARBON 4.7K 5% 1/4W F
R306 1-249-441-11 CARBON 100K 5% 1/4W * CN501 1-564-527-11 PLUG, CONNECTOR 12P
CN502 1-774-108-11 PIN, CONNECTOR (PC BOARD) 2P
R308 1-247-903-00 CARBON 1M 5% 1/4W
R310 1-247-903-00 CARBON 1M 5% 1/4W < FUSE >
R311 1-249-441-11 CARBON 100K 5% 1/4W
R312 1-249-419-11 CARBON 1.5K 5% 1/4W F ! F501 1-532-505-31 FUSE T5AL/250V
R313 1-247-863-91 CARBON 22K 5% 1/4W ! F504 1-532-506-31 FUSE T6.3A/250V
! F505 1-532-506-31 FUSE T6.3A/250V
R314 1-247-863-91 CARBON 22K 5% 1/4W < FUSE HOLDER >
R315 1-249-439-11 CARBON 68K 5% 1/4W
R316 1-249-437-11 CARBON 47K 5% 1/4W FH501 1-533-233-21 HOLDER, FUSE
R321 1-249-440-11 CARBON 82K 5% 1/4W FH502 1-533-233-21 HOLDER, FUSE
R322 1-249-441-11 CARBON 100K 5% 1/4W FH507 1-533-233-21 HOLDER, FUSE
FH508 1-533-233-21 HOLDER, FUSE
R323 1-249-441-11 CARBON 100K 5% 1/4W FH509 1-533-233-21 HOLDER, FUSE
R331 1-247-890-11 CARBON 300K 5% 1/4W
R332 1-249-429-11 CARBON 10K 5% 1/4W FH510 1-533-233-21 HOLDER, FUSE
R333 1-249-431-11 CARBON 15K 5% 1/4W
! R401 1-215-893-11 METAL OXIDE 1.5K 5% 2W F < RESISTOR >

! R402 1-215-893-11 METAL OXIDE 1.5K 5% 2W F ! R501 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
! R404 1-215-893-11 METAL OXIDE 1.5K 5% 2W F ! R502 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R405 1-249-429-11 CARBON 10K 5% 1/4W ! R503 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R406 1-249-437-11 CARBON 47K 5% 1/4W ! R504 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
R407 1-249-437-11 CARBON 47K 5% 1/4W
< SWITCH >
R408 1-249-440-11 CARBON 82K 5% 1/4W
R409 1-249-440-11 CARBON 82K 5% 1/4W ! S501 1-771-291-11 SWITCH, POWER (VOLTAGE SELECTOR)
R429 1-249-437-11 CARBON 47K 5% 1/4W
R431 1-249-437-11 CARBON 47K 5% 1/4W < TRANSFORMER >

< RELAY > ! T501 1-431-828-11 TRANSFORMER, POWER

RY401 1-755-141-11 RELAY **************************************************************

RY402 1-755-141-11 RELAY
RY404 1-515-920-11 RELAY (24V) * A-4414-188-A VIDEO BOARD, COMPLETE
*********************
< THERMISTOR >
< CAPACITOR >
THP321 1-807-796-11 THERMISTOR
C101 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
< TERMINAL > C102 1-163-143-00 CERAMIC CHIP 0.0012uF 5% 50V
C103 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
TM401 1-537-842-11 TERMINAL BOARD (FRONT SPEAKER) C104 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
TM402 1-537-240-11 TERMINAL BOARD (CHECKER PIN) C201 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
(SURROUND SPEAKER)
C202 1-163-143-00 CERAMIC CHIP 0.0012uF 5% 50V
************************************************************** C203 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C301 1-163-127-00 CERAMIC CHIP 270PF 5% 50V
* 1-658-576-11 SENSOR BOARD C302 1-163-127-00 CERAMIC CHIP 270PF 5% 50V
************* C303 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

< IC > C304 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

C305 1-163-263-11 CERAMIC CHIP 330PF 5% 50V
IC702 8-749-924-18 IC PHOTO INTERRUPTER RPI-1391 C306 1-163-263-11 CERAMIC CHIP 330PF 5% 50V
IC703 8-749-924-30 IC PHOTO REFLECTOR GP2S28 C310 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
C311 1-216-295-91 SHORT 0

The components identified by mark ! or dotted

line with mark ! are critical for safety.
– 120 – Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
 VIDEO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C313 1-165-319-11 CERAMIC CHIP 0.1uF 50V C566 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C314 1-165-319-11 CERAMIC CHIP 0.1uF 50V C568 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C318 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C569 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C319 1-165-319-11 CERAMIC CHIP 0.1uF 50V C570 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C401 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C571 1-128-065-11 ELECT CHIP 68uF 20% 10V
C402 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C573 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C403 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C574 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C404 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C576 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C405 1-110-530-11 ELECT CHIP 1000uF 20% 6.3V C577 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C406 1-110-530-11 ELECT CHIP 1000uF 20% 6.3V
< CONNECTOR >
C407 1-165-319-11 CERAMIC CHIP 0.1uF 50V
(FORMER TYPE)(*NOTE) CN501 1-770-706-11 CONNECTOR, FFC/FPC 23P
C408 1-165-319-11 CERAMIC CHIP 0.1uF 50V CN503 1-779-416-11 CONNECTOR,FFC(LIF(NON-ZIF))13P
(FORMER TYPE)(*NOTE)
C409 1-124-778-00 ELECT CHIP 22uF 20% 6.3V < TRIMMER >
C410 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C411 1-165-319-11 CERAMIC CHIP 0.1uF 50V CT503 1-141-539-11 CAP, ADJ 10PF

C412 1-165-319-11 CERAMIC CHIP 0.1uF 50V < DIODE >

C413 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C452 1-165-319-11 CERAMIC CHIP 0.1uF 50V D301 8-719-054-23 DIODE RB706D-40-T146
C501 1-163-251-11 CERAMIC CHIP 100PF 5% 50V D501 8-719-422-12 DIODE MA8039
C502 1-163-251-11 CERAMIC CHIP 100PF 5% 50V D502 8-719-018-51 DIODE CL-170R-CD

C503 1-163-251-11 CERAMIC CHIP 100PF 5% 50V < IC >

C504 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C505 1-126-206-11 ELECT CHIP 100uF 20% 6.3V IC101 8-759-701-39 IC NJM3404AM
C506 1-165-319-11 CERAMIC CHIP 0.1uF 50V IC401 8-759-262-00 IC MC14576CF
C507 1-126-206-11 ELECT CHIP 100uF 20% 6.3V IC402 8-759-535-49 IC M38513M4-050FP (FORMER TYPE)(*NOTE)
IC501 8-759-269-92 IC SN74HCU04ANS-E20
C509 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V IC502 8-759-549-26 IC M30620MC-305FP (NEW TYPE)(*NOTE)
C510 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C531 1-126-206-11 ELECT CHIP 100uF 20% 6.3V IC504 8-759-269-92 IC SN74HCU04ANS-E20
C532 1-165-319-11 CERAMIC CHIP 0.1uF 50V IC505 8-759-535-48 IC CL680T-D1
C535 1-165-319-11 CERAMIC CHIP 0.1uF 50V IC506 8-759-535-61 IC LC372100PM-H95
IC507 8-759-342-01 IC MB814260-70PJER
C536 1-126-193-11 ELECT 1uF 20% 50V IC509 8-759-535-62 IC PCM1727E-2/T2
C537 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C539 1-165-319-11 CERAMIC CHIP 0.1uF 50V < JACK >
C540 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C541 1-165-319-11 CERAMIC CHIP 0.1uF 50V J301 1-537-943-11 TERMINAL, S (S VIDEO OUT)
J302 1-774-227-11 JACK, PIN 1P (VIDEO OUT)
C542 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C543 1-126-206-11 ELECT CHIP 100uF 20% 6.3V < JUMPER RESISTOR >
C544 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C545 1-165-319-11 CERAMIC CHIP 0.1uF 50V JW101 1-216-295-91 SHORT 0
C546 1-165-319-11 CERAMIC CHIP 0.1uF 50V JW201 1-216-295-91 SHORT 0
JW401 1-216-295-91 SHORT 0
C547 1-126-193-11 ELECT 1uF 20% 50V JW402 1-216-295-91 SHORT 0
C548 1-165-319-11 CERAMIC CHIP 0.1uF 50V JW403 1-216-295-91 SHORT 0
C549 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C550 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V JW404 1-216-295-91 SHORT 0
C551 1-165-319-11 CERAMIC CHIP 0.1uF 50V JW405 1-216-295-91 SHORT 0
JW413 1-216-295-91 SHORT 0
C552 1-165-319-11 CERAMIC CHIP 0.1uF 50V JW421 1-216-295-91 SHORT 0 (NEW TYPE)(*NOTE)
C553 1-126-206-11 ELECT CHIP 100uF 20% 6.3V JW422 1-216-295-91 SHORT 0 (NEW TYPE)(*NOTE)
C555 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C556 1-165-319-11 CERAMIC CHIP 0.1uF 50V JW502 1-216-295-91 SHORT 0
C559 1-126-206-11 ELECT CHIP 100uF 20% 6.3V JW503 1-216-295-91 SHORT 0
JW504 1-216-295-91 SHORT 0
C560 1-163-235-11 CERAMIC CHIP 22PF 5% 50V JW505 1-216-295-91 SHORT 0
C561 1-163-099-00 CERAMIC CHIP 18PF 5% 50V JW506 1-216-295-91 SHORT 0
C562 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C563 1-165-319-11 CERAMIC CHIP 0.1uF 50V < COIL >
C564 1-165-319-11 CERAMIC CHIP 0.1uF 50V
L301 1-410-372-21 INDUCTOR CHIP 1.8uH
C565 1-126-206-11 ELECT CHIP 100uF 20% 6.3V L302 1-410-372-21 INDUCTOR CHIP 1.8uH

* Note
When replacing IC502, refer to “IC502 of
Video Board” in “Service Note” (page 13).
– 121 –
Downloaded from www.Manualslib.com manuals search engine
 VIDEO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
L501 1-216-296-91 SHORT 0 R333 1-216-046-00 METAL CHIP 750 5% 1/10W
L502 1-216-296-91 SHORT 0 R335 1-216-073-00 METAL CHIP 10K 5% 1/10W
L503 1-216-296-91 SHORT 0 R336 1-216-073-00 METAL CHIP 10K 5% 1/10W
R340 1-216-022-00 METAL CHIP 75 5% 1/10W
L504 1-410-375-11 INDUCTOR CHIP 3.3uH
L505 1-216-296-91 SHORT 0 R341 1-216-121-91 RES,CHIP 1M 5% 1/10W
L506 1-216-296-91 SHORT 0 R342 1-216-022-00 METAL CHIP 75 5% 1/10W
L507 1-216-296-91 SHORT 0 R403 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
L508 1-216-296-91 SHORT 0 R404 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R405 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
L509 1-216-296-91 SHORT 0
L510 1-216-296-91 SHORT 0 R406 1-216-081-00 METAL CHIP 22K 5% 1/10W
R407 1-216-073-00 METAL CHIP 10K 5% 1/10W
< TRANSISTOR > R408 1-216-073-00 METAL CHIP 10K 5% 1/10W
R409 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q301 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R410 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q302 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L
Q303 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R411 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q304 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R412 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q306 8-729-027-60 TRANSISTOR DTC144TKA-T146 R413 1-216-025-91 RES,CHIP 100 5% 1/10W
(FORMER TYPE)(*NOTE)
Q307 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R414 1-216-081-00 METAL CHIP 22K 5% 1/10W
Q308 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R415 1-216-081-00 METAL CHIP 22K 5% 1/10W
Q310 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L
Q453 8-729-216-22 TRANSISTOR 2SA1162-G R421 1-216-025-91 RES,CHIP 100 5% 1/10W
Q454 8-729-216-22 TRANSISTOR 2SA1162-G (FORMER TYPE)(*NOTE)
R422 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q502 8-729-024-91 TRANSISTOR 2SC2721-GL-TE85L (FORMER TYPE)(*NOTE)
Q531 8-729-140-75 TRANSISTOR 2SD999-CLCK R423 1-216-073-00 METAL CHIP 10K 5% 1/10W
R424 1-216-073-00 METAL CHIP 10K 5% 1/10W
< RESISTOR > R425 1-216-073-00 METAL CHIP 10K 5% 1/10W

R101 1-216-073-00 METAL CHIP 10K 5% 1/10W R426 1-216-073-00 METAL CHIP 10K 5% 1/10W
R102 1-208-441-61 RES,CHIP 1.5K 2% 1/10W R457 1-216-025-91 RES,CHIP 100 5% 1/10W
R103 1-208-441-61 RES,CHIP 1.5K 2% 1/10W R458 1-216-025-91 RES,CHIP 100 5% 1/10W
R105 1-216-295-91 SHORT 0 R459 1-216-025-91 RES,CHIP 100 5% 1/10W
R201 1-216-073-00 METAL CHIP 10K 5% 1/10W R461 1-216-025-91 RES,CHIP 100 5% 1/10W

R202 1-208-441-61 RES,CHIP 1.5K 2% 1/10W R462 1-216-025-91 RES,CHIP 100 5% 1/10W
R203 1-208-441-61 RES,CHIP 1.5K 2% 1/10W R463 1-216-025-91 RES,CHIP 100 5% 1/10W
R205 1-216-295-91 SHORT 0 R464 1-216-025-91 RES,CHIP 100 5% 1/10W
R301 1-216-624-11 METAL CHIP 75 0.5% 1/10W R501 1-216-025-91 RES,CHIP 100 5% 1/10W
R302 1-216-624-11 METAL CHIP 75 0.5% 1/10W R502 1-216-025-91 RES,CHIP 100 5% 1/10W

R305 1-216-049-91 RES,CHIP 1K 5% 1/10W R503 1-216-025-91 RES,CHIP 100 5% 1/10W

R306 1-216-073-00 METAL CHIP 10K 5% 1/10W R504 1-216-025-91 RES,CHIP 100 5% 1/10W
R307 1-216-049-91 RES,CHIP 1K 5% 1/10W R505 1-216-025-91 RES,CHIP 100 5% 1/10W
R308 1-216-049-91 RES,CHIP 1K 5% 1/10W R506 1-216-025-91 RES,CHIP 100 5% 1/10W
R309 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R507 1-216-073-00 METAL CHIP 10K 5% 1/10W

R312 1-216-073-00 METAL CHIP 10K 5% 1/10W R508 1-216-081-00 METAL CHIP 22K 5% 1/10W
R313 1-216-049-91 RES,CHIP 1K 5% 1/10W R509 1-216-081-00 METAL CHIP 22K 5% 1/10W
R314 1-216-049-91 RES,CHIP 1K 5% 1/10W R510 1-216-081-00 METAL CHIP 22K 5% 1/10W
R315 1-216-047-91 RES,CHIP 820 5% 1/10W R511 1-216-081-00 METAL CHIP 22K 5% 1/10W
R316 1-216-657-11 METAL CHIP 1.8K 0.5% 1/10W R512 1-216-081-00 METAL CHIP 22K 5% 1/10W

R317 1-216-683-11 METAL CHIP 22K 0.5% 1/10W R513 1-216-081-00 METAL CHIP 22K 5% 1/10W
R318 1-216-041-00 METAL CHIP 470 5% 1/10W R514 1-216-081-00 METAL CHIP 22K 5% 1/10W
R319 1-216-049-91 RES,CHIP 1K 5% 1/10W R516 1-216-073-00 METAL CHIP 10K 5% 1/10W
R320 1-216-651-11 METAL CHIP 1K 0.5% 1/10W R517 1-216-073-00 METAL CHIP 10K 5% 1/10W
R321 1-216-049-91 RES,CHIP 1K 5% 1/10W R518 1-216-073-00 METAL CHIP 10K 5% 1/10W

R324 1-216-022-00 METAL CHIP 75 5% 1/10W R519 1-216-025-91 RES,CHIP 100 5% 1/10W
R325 1-216-295-91 SHORT 0 R520 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R327 1-216-049-91 RES,CHIP 1K 5% 1/10W R523 1-216-013-00 METAL CHIP 33 5% 1/10W
R328 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W R530 1-216-081-00 METAL CHIP 22K 5% 1/10W
R329 1-216-649-11 METAL CHIP 820 0.5% 1/10W R531 1-216-025-91 RES,CHIP 100 5% 1/10W

R332 1-216-651-11 METAL CHIP 1K 0.5% 1/10W R532 1-216-025-91 RES,CHIP 100 5% 1/10W

* Note
When replacing IC502, refer to “IC502 of
Video Board” in “Service Note” (page 13).
– 122 –
Downloaded from www.Manualslib.com manuals search engine
 VIDEO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R533 1-216-025-91 RES,CHIP 100 5% 1/10W MISCELLANEOUS
R534 1-216-073-00 METAL CHIP 10K 5% 1/10W *************
R535 1-216-073-00 METAL CHIP 10K 5% 1/10W
R536 1-216-033-00 METAL CHIP 220 5% 1/10W 6 1-693-421-11 TUNER (FM/AM)
8 1-773-009-11 WIRE (FLAT TYPE) (15 CORE)(150mm)
R537 1-216-025-91 RES,CHIP 100 5% 1/10W 9 1-775-212-11 WIRE (FLAT TYPE) (23 CORE)
R538 1-216-073-00 METAL CHIP 10K 5% 1/10W 10 1-690-589-31 WIRE (FLAT TYPE) (13 CORE)
R542 1-216-049-91 RES,CHIP 1K 5% 1/10W
R543 1-216-685-11 METAL CHIP 27K 0.5% 1/10W 54 1-773-041-11 WIRE (FLAT TYPE) (17 CORE)
R544 1-216-659-11 METAL CHIP 2.2K 0.5% 1/10W ! 58 1-569-007-11 ADAPTOR, CONVERSION 2P (IA)
! 58 1-569-008-21 ADAPTOR, CONVERSION 2P (SP,MY,EA,TW)
R545 1-216-025-91 RES,CHIP 100 5% 1/10W ! 58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
R546 1-216-049-91 RES,CHIP 1K 5% 1/10W ! 59 1-558-943-41 CORD, POWER (IA)
R547 1-216-295-91 SHORT 0
R548 1-216-049-91 RES,CHIP 1K 5% 1/10W ! 59 1-575-651-21 CORD, POWER (SP,MY,EA,HK,TW)
R549 1-216-025-91 RES,CHIP 100 5% 1/10W 60 1-783-898-11 WIRE (FLAT TYPE) (15 CORE)
121 1-769-972-11 WIRE (FLAT TYPE) (13 CORE)
R550 1-216-025-91 RES,CHIP 100 5% 1/10W 130 1-773-108-11 WIRE (FLAT TYPE) (19 CORE)
R551 1-216-025-91 RES,CHIP 100 5% 1/10W 257 1-452-879-11 MAGNET
R552 1-216-025-91 RES,CHIP 100 5% 1/10W
R554 1-216-025-91 RES,CHIP 100 5% 1/10W 258 1-776-042-11 WIRE (FLAT TYPE) (8CORE)
R555 1-216-121-91 RES,CHIP 1M 5% 1/10W ! 301 8-820-020-02 OPTICAL PICK-UP BLOCK KSS-213D/Q-NP
302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)
R556 1-216-025-91 RES,CHIP 100 5% 1/10W HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR1)
R557 1-216-025-91 RES,CHIP 100 5% 1/10W HP101 A-2056-683-A DECK (A) ASSY, HEAD (230PWR1)
R558 1-216-073-00 METAL CHIP 10K 5% 1/10W
R559 1-216-073-00 METAL CHIP 10K 5% 1/10W HRPE101 A-2056-682-A DECK (B) ASSY, HEAD (230AWR1)
R560 1-216-051-00 METAL CHIP 1.2K 5% 1/10W HRPE101 A-2056-684-A DECK (B) ASSY, HEAD (230PWR1)
M1 A-2004-628-A MOTOR ASSY, CAPSTAN
R561 1-216-049-91 RES,CHIP 1K 5% 1/10W M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
R567 1-216-073-00 METAL CHIP 10K 5% 1/10W M102 X-4917-504-1 MOTOR ASSY (SLED)
R568 1-216-073-00 METAL CHIP 10K 5% 1/10W
R569 1-216-073-00 METAL CHIP 10K 5% 1/10W M701 A-4672-004-A MOTOR ASSY (TURN)
R572 1-216-073-00 METAL CHIP 10K 5% 1/10W M801 A-4672-004-A MOTOR ASSY (SLIDE)
M901 1-763-048-21 FAN, D.C.
R573 1-216-073-00 METAL CHIP 10K 5% 1/10W ND601 1-517-731-21 INDICATOR TUBE, FLUORESCENT
R574 1-216-073-00 METAL CHIP 10K 5% 1/10W S811 1-473-335-11 ENCODER,ROTARY (BU,TRAY ADDRESS DET)
R577 1-216-081-00 METAL CHIP 22K 5% 1/10W
R578 1-216-081-00 METAL CHIP 22K 5% 1/10W ! T501 1-431-828-11 TRANSFORMER, POWER
R579 1-216-073-00 METAL CHIP 10K 5% 1/10W
**************************************************************
R580 1-216-073-00 METAL CHIP 10K 5% 1/10W
**************
< SWITCH > HARDWARE LIST
**************
S501 1-571-395-11 SWITCH, SLIDE (SYSTEM SELECT)
#1 7-685-872-09 SCREW +BVTT 3X8 (S)
< VIBRATOR > #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
X401 1-767-261-21 VIBRATOR, CERAMIC (8MHz) #4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
(FORMER TYPE)(*NOTE) #5 7-685-871-01 SCREW +BVTT 3X6 (S)
X501 1-767-510-11 VIBRATOR, CERAMIC (10MHz)
X503 1-767-519-11 VIBRATOR, CRYSTAL (27MHz) #6 7-685-880-09 SCREW +BVTT 4X6 (S)
#7 7-685-851-04 SCREW +BVTT 2X4 (S)
************************************************************** #8 7-621-775-10 SCREW +B 2.6X4
#9 7-621-255-15 SCREW +P 2X3
#10 7-685-850-04 SCREW +BVTT 2X3 (S)

#11 7-628-254-15 SCREW +PS 2.6X6

#12 7-628-254-50 SCREW +PS 2.6X16

* Note The components identified by mark ! or dotted

When replacing IC502, refer to “IC502 of line with mark ! are critical for safety.
Video Board” in “Service Note” (page 13). – 123 – Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
 HCD-V818

Sony Corporation 98F0924-1

Printed in Japan © 1998. 6
9-922-901-11 Home A&V Products Company Published by Quality Assurance Dept.
– 124 – (Shibaura)
Downloaded from www.Manualslib.com manuals search engine