HCD-GRX10AV/RX110AV

SERVICE MANUAL Canadian Model

AEP Model
UK Model
HCD-RX110AV

E Model
Australian Model
HCD-GRX10AV

HCD-GRX10AV/RX110AV is the
tuner, deck, CD and amplifier section
in MHC-GRX10AV/RX110AV. Photo: HCD-GRX10AV

Model Name Using Similar Mechanism HCD-H991AV

CD Mechanism Type CDM38L-5BD29AL/
CD
CDM38LH-5BD29AL
SECTION
Base Unit Type BU-5BD29AL
Optical Pick-up Type KSS-213D/Q-NP
TAPE Model Name Using Similar Mechanism NEW
DECK
SECTION Tape Transport Mechanism Type TCM-230AWR1/230PWR1

SPECIFICATIONS

— Continued on next page —

COMPACT DISC DECK RECEIVER

MICROFILM

–1–
Downloaded from www.Manualslib.com manuals search engine
 –2–
Downloaded from www.Manualslib.com manuals search engine
 CAUTION NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
Use of controls or adjustments or performance of procedures OR BASE UNIT
other than those specified herein may result in hazardous ra-
diation exposure. The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
Notes on chip component replacement charged electrostatic load, etc. on clothing and the human body.
• Never reuse a disconnected chip component. During repair, pay attention to electrostatic break-down and also
• Notice that the minus side of a tantalum capacitor may be use the procedure in the printed matter which is included in the
damaged by heat. repain parts.
The flexible board is easily damaged and should be handled with
Flexible Circuit Board Repairing care.
• Keep the temperature of soldering iron around 270˚C
during repairing. NOTES ON LASER DIODE EMISSION CHECK
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times). The laser beam on this model is concentrated so as to be focused on
• Be careful not to apply force on the conductor when soldering the disc reflective surface by the objective lens in the optical pick-
or unsoldering. up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1. LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
This appliance is classified as
a CLASS 1 LASER product. Carry out the “S curve check” in “CD section adjustment” and check
The CLASS 1 LASER PROD- that the S curve waveform is output three times.
UCT MARKING is located on
the rear exterior.
MODEL IDENTIFICATION
— BACK PANEL —
The following
caution label is
located inside of
the unit.

Parts No.

• Abbreviation
SAFETY-RELATED COMPONENT WARNING !! CND : Canadian model
G : German model
EE : East European model
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE EA : Saudi arabia model
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN HK : Hong Kong model
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. SP : Singapore model
MY : Malaysia model
REPLACE THESE COMPONENTS WITH SONY PARTS AUS : Australian model
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS TH : Thai model
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. E2 : Without SW tuner E model.
E3 : With SW tuner E model.

ATTENTION AU COMPOSANT AYANT RAPPORT PARTS No. MODEL

À LA SÉCURITÉ!! 4-996-819-0π RX110AV: AEP, UK, G
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR
4-996-819-1π RX110AV: EE, CIS
4-996-819-2π RX110AV: CND
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
4-996-819-3π GRX10AV: TH
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE 4-996-820-0π GRX10AV: E2, E3
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS 4-996-820-1π GRX10AV: SP, MY
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS 4-996-820-2π GRX10AV: HK
SONT DONNÉS DANS CE MANUEL OU DANS LES 4-996-820-3π GRX10AV: AUS
SUPPLÉMENTS PUBLIÉS PAR SONY. 4-996-820-4π GRX10AV: EA

–3–
Downloaded from www.Manualslib.com manuals search engine
 TABLE OF CONTENTS

1. SERVICING NOTE .......................................................... 5 7-11. Printed Wiring Board – Main Section – ........................... 51
7-12. Schematic Diagram – Main (1/4) Section – ..................... 53
2. GENERAL .......................................................................... 6 7-13. Schematic Diagram – Main (2/4) Section – ..................... 55
7-14. Schematic Diagram – Main (3/4) Section – ..................... 57
7-15. Schematic Diagram – Main (4/4) Section – ..................... 59
3. DISASSEMBLY 7-16. Printed Wiring Board – Mic/HP Section – ....................... 61
3-1. Loading Panel ....................................................................... 8
7-17. Schematic Diagram – Mic/HP Section – .......................... 62
3-2. Front Panel ........................................................................... 8
7-18. Printed Wiring Board – Power Section – ......................... 63
3-3. Cassette Mechanism Deck .................................................... 9
7-19. Schematic Diagram – Power Section – ............................ 65
3-4. Panel Board and Cont Com Board ........................................ 9
7-20. Schematic Diagram – Transformer Section – ................... 67
3-5. Disc Tray ........................................................................... 10
7-21. Printed Wiring Board – Transformer Section – ................ 69
7-22. Printed Wiring Board – Leaf SW Section – ..................... 70
4. SERVICE MODE ............................................................ 11 7-23. Schematic Diagram – Leaf SW Section – ........................ 70
7-24. Printed Wiring Board – Display Section – ....................... 71
5. MECHANICAL ADJUSTMENTS .......................... 14 7-25. Schematic Diagram – Display Section – .......................... 73
7-26. Schematic Diagram – Panel Section – ............................. 75
6. ELECTRICAL ADJUSTMENTS ............................... 14 7-27. Printed Wiring Board – Panel Section – ........................... 77
7-28. Schematic Diagram – CD Motor Section – ...................... 79
7. DIAGRAMS 7-29. Printed Wiring Board – CD Motor Section – ................... 81
7-1. Circuit Boards Location ...................................................... 20 7-30. Schematic Diagram – Surround Section – ....................... 83
7-2. Block Diagrams 7-31. Printed Wiring Board – Surround Section – ..................... 83
• Tuner Section (AEP, UK, German model) ....................... 21 7-32. IC Block Diagrams ........................................................... 84
• Tuner Section (East European, CIS model) ..................... 23 7-33. IC Pin Functions ............................................................... 90
• CD Section ....................................................................... 25
• Deck Section .................................................................... 27 8. EXPLODED VIEWS
• Main Section .................................................................... 29 8-1. Case Section ...................................................................... 100
• Power Section .................................................................. 31 8-2. Chassis Section ................................................................. 101
• Display Section ................................................................ 33 8-3. Front Panel Section ........................................................... 102
7-3. Printed Wiring Board – CD Section – ................................. 37 8-4. CD Mechanism Deck Section-1
7-4. Schematic Diagram – CD Section – ................................... 39 (CDM38L-5BD29AL, CDM38LH-5BD29AL) ............... 103
7-5. Schematic Diagram 8-5. CD Mechanism Deck Section-2
–Tuner (AEP, UK, German model) Section – ..................... 41 (CDM38L-5BD29AL, CDM38LH-5BD29AL) ............... 104
7-6. Printed Wiring Board 8-6. Base Unit Section (BU-5BD29AL) .................................. 105
–Tuner (AEP, UK, German model) Section – ..................... 43 8-7. TC Mechanism Section 1
7-7. Printed Wiring Board (TCM230AWR1, TCM230PWR1) ................................... 106
–Tuner (East European, CIS model) Section – ................... 44 8-8. TC Mechanism Section 2
7-8. Schematic Diagram (TCM230AWR1, TCM230PWR1) ................................... 107
–Tuner (East European, CIS model) Section – ................... 45
7-9. Schematic Diagram – Deck Section – ................................. 47 9. ELECTRICAL PARTS LIST ...................................... 108
7-10. Printed Wiring Board – Deck Section – ........................... 49

–4–
Downloaded from www.Manualslib.com manuals search engine
 SECTION 1
SERVICING NOTE
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF

1 Remove the Case.

3 pull-out the disc tray.

2 Turn the cam to the

direction of arrow.

Note for Installation (ROTARY ENCODER)

Note:When attaching the Base unit, Insert the

BU cam section A into the groove of BU cam.

Section A
Groove

Note:When attaching the BU cam,

engage the Rotary encoder
switch as shown in the figure.

–5–
Downloaded from www.Manualslib.com manuals search engine
 SECTION 2
GENERAL
Front Panel

1 2 3 4 5 6

7
8

10

11
12
13

14

54 15
53
52
51
50
49 16
48 17
18
47 19
20
46
45 21
44 22
43
23
42
24
25
41
26

40 27

39 38 37 36 35 34 33 32 31 30 29 28

–6–
Downloaded from www.Manualslib.com manuals search engine
 LOCATION OF PARTS AND CONTROLS

1 1/u button
2 DISC 1 button
3 DISC 2 button
4 DISC 3 button
5 DISC SKIP/EX-CHANGE button
6 § button
7 FUNCTION button
8 Deck A ª button
9 Deck A · button
10 Deck B ª button
11 Deck B · button
12 CD ·∏ button
13 PLAY MODE/DOLBY NR/TUNER MEMORY button
14 EDIT/DIRECTION button
15 REPEAT/STEREO/MONO button
16 TUNER/BAND button
17 p button
18 PRO LOGIC button
19 DSP button
20 KARAOKE PON/MPX button
21 PTY button (AEP, UK, G model)
22 PHONES jack
23 r REC button
24 P PAUSE button
25 HI-PUB button
26 CD SYNC button
27 VOLUME knob
28 GROOVE button
29 DBFB button
30 )/+ button
31 ENTER/NEXT button
32 JOG button
33 AUTO BPM
34 0/– button
35 BEAT LEVEL button
36 JAM button
37 SPEED button
38 SELECT button
39 ON/OFF button
40 MIX MIC jack
41 MIC LEVEL knob
42 PAD A button
43 PAD B button
44 NON STOP button
45 FLASH button
46 LOOP button
47 FILE SELECT button
48 EFFECT button
49 GEQ CONTROL button
50 P FILE MEMORY button
51 DISPLAY button
52 DEMO button
53 CLOCK/TIMER SET button
54 TIMER/SELECT button

–7–
Downloaded from www.Manualslib.com manuals search engine
 SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.

3-1. LOADING PANEL

3 Loading panel

Claws

1 Turn the cam to the direction

of arrow.
2 Pull-out the disc tray.

3-2. FRONT PANEL

6 Flat type wire

7 Flat type wire (CN107)
(CN106)

8 Flat type wire

(CN101)
3 Screw
(BVTP3x10) 4 Connector
(CN203)

2 Screw
(BVTP3x10)

5 Connector
9 Front panel assembly (CN752)

1 Three screws
(BVTP3x8)

–8–
Downloaded from www.Manualslib.com manuals search engine
 3-3. CASSETTE MECHANISM DECK
9 Three screws
(BVTP 2.6x8)
!§ Mechanism deck
!º Two screws
(BVTP 2.6x8)
6 Remove the cassette lids. 2 Two screws
(BVTT 2x4) !¢ Two screws
(BVTP 2.6x8)

4 Damper, oil

3 Damper, oil

1 Two screws
(BVTT 2x4)

7 Spring !∞ Bracket
!¡ Screw
!™ Screw (BVTP 2.6x8)
(BVTP 2.6x8)
!£ Wire holder

5 Push the cassette lids.

8 Spring

3-4. PANEL BOARD AND CONT COM BOARD

1 Ten screws
4 Shield (BVTP 2.6x8)

2 Three screws
(BVTP 2.6x8)

7 Nut

!¡ Wire

!º Screw
(BVTP 2.6x8)

6 Konb(Jog)
!¢ CONT COM board 5 Flat type wire
3 Panel board
(CN602)

8 Konb(Volume)
9 Nut

!™ Four screws
(BVTP 2.6x8)
!£ Six screws
(BVTP 2.6x8)

–9–
Downloaded from www.Manualslib.com manuals search engine
 3-5. DISC TRAY
(Perfom after removing the front panel.) Note: When installing the Disc tray, pull around the flat type wire to
pass through the clawA and clawB, as shown in the figure.

3 Flat type wire (8 core)

4 Two claws

2 Pull-out the disc tray.

5 Remove the disc tray.
ClawB
ClawA

1 Turn the cam the

direction of arrow.

– 10 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 4
SERVICE MODE
MC Cold Reset
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the
customer.
Procedure:
1. Press three buttons p , ENTER/NEXT , and 1/u simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

CD Delivery Mode
• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press 1/u button to turn the set ON.
2. Press LOOP button and 1/u button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.

MC Hot Reset
• This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions same as if the power cord is plugged
in and out.
Procedure:
1. Press three buttons p , ENTER/NEXT , and DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

Sled Servo Mode

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons p , ENTER/NEXT , and § simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4. With the CD in stop status, press ) + utton move the pick-up to outside track, or – 0 button to inside track.
5. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.

Change-over of AM Tuner Step between 9kHz and 10kHz

• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “AM”.
3. Press 1/u button to turn the set OFF.
4. Press ENTER/NEXT and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “AM 9k STEP” or “AM
10k STEP”, and thus the channel step is changed over.

LED and Fluorescent Indicator Tube All Lit, Key Check Mode
Procedure:
1. Press three buttons p , ENTER/NEXT , and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays “K 1 V0 J0”. Each time a button is pressed, “K”value increases. However,
once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.

– 11 –
Downloaded from www.Manualslib.com manuals search engine
 Aging Mode
This mode can be used for checking the operations of the CD player and tape deck.
• When problems occur;
Aging stops, and the stopped state is displayed on the fluorescent display tube.
• When no problems;
Aging continues.

Preparations:
• Set the CD on the DISC1 tray.
• Insert a commercially available tape for recording (tapes which contents can be erased, etc.) in decks A and B.

Setting the aging mode:

Press the p button, ENTER/NEXT button, and DISC SKIP/EX-CHANGE button together.
When the aging mode is set, the CD roulette mark blinks. To exit the mode, press the 1/u button and turn OFF the power.

Sequence:
The aging mode is executed in the following sequence.
If the function is set to “CD” when the aging mode is set, aging is performed starting from the CD player. When set to “TAPE A” or “TAPE
B”, aging is started from deck A.
If the function is set to others, aging will not be started until the function is switched to CD or TAPE.

Aging of CD player (12 minutes)

Aging of deck A
Maximum about 12 minutes
Aging of deck B

Display of status:
• The aging status is displayed on the fluorescent display tube.
• Normally, the CD player displays the remaining aging time. But if operations ended abnormally, it displays the cause.
• During the aging of the tape deck, the operations performed will be displayed. If operations ended abnormally, this will be displayed at the
fluorescent display tube.

CD Player
• During normal operations:
Display of fluorescent display tube

**1-@@

**: Displays “CD” and the remaining aging time (minutes) alternately. The remaining aging time is counted down from 12.

@@: Track number being accessed.

• When operations end abnormally:

Display of fluorescent display tube

Display Main Cause
NO DISC ERR DISC 1 is NO DISC from the beginning
FOCUS1 ERR Focus is not imposed properly
FOCUS2 ERR The focus deviated several times after the disc rotated normally
GFS ERR GFS ERROR
FBIAS ERR Error during focus bias adjustment
SENSOR ERR DISC 1 was found to be NO DISC by the disc sensor
TABLE ERR The table did not rotate normally
TRAY ERR The tray containing the BD did not operate normally

– 12 –
Downloaded from www.Manualslib.com manuals search engine
 Tape Deck
Display of Operations Operation Timing of Ending
TAPE A AG-1 TAPE A REW Shutoff
TAPE A AG-2 TAPE A FWD 2 minute playback
TAPE A AG-3 TAPE A FF 20 seconds or shutoff
TAPE A AG-4 TAPE A REV 2 minutes playback
TAPE A AG-5 TAPE A REW Shutoff
TAPE B AG-1 TAPE B REW Shutoff
TAPE B AG-2 TAPE B FWD 2 minute playback
TAPE B AG-3 TAPE B FF 20 seconds or shutoff
TAPE B AG-4 TAPE B REV 2 minute playback
TAPE B AG-5 TAPE B REW Shutoff

Operations during aging

• Operations are performed in the following sequence during aging

<CD player>
1. The CD tray rotates and disc 1 is selected.
2. Chucking is performed.
3. TOC is read.
4. Track 1 played back for 2 seconds.
5. The last track is played back for 2 seconds.
6. 1 to 5 is repeated.
7. After 12 minutes of aging, aging is switched to the tape deck.

<Tape Deck>
1. The tape in deck A is rewound to the head.
2. The FWD side is played back for 2 minutes.
3. The tape is fast forwarded (FF) for 20 seconds. The following procedure is performed when the tape end is reached before the 20 seconds.
4. The REV side is played back for 2 minutes.
5. The tape is rewound to the head (REW).
6. The tape in deck B is rewound to the head.
7. The FWD side is played back for 2 minutes.
8. The tape is fast forwarded (FF) for 20 seconds. The following procedure is performed when the tape end is reached before the 20 seconds.
9. The REV side is played back for 2 minutes.
10. The tape is rewound to the head (REW).
11. Aging is switched to the CD player.

– 13 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution DECK SECTION 0 dB=0.775V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head damagnetizer.
record/playback heads pinch rollers 2. Do not use a magnetized screwdriver for the adjustments.
erase head rubber belts 3. After the adjustments, apply suitable locking compound to the
capstan idlers parts adjusted.
2. Demagnetize the record/playback head with a head demagne- 4. The adjustments should be performed with the rated power sup-
tizer. ply voltage unless otherwise noted.
3. Do not use a magnetized screwdriver for the adjustments. 5. The adjustments should be performed in the order given in this
4. After the adjustments, apply suitable locking compound to the service manual. (As a general rule, playback circuit adjustment
parts adjusted. should be completed before performing recording circuit adjust-
5. The adjustments should be performed with the rated power sup- ment.)
ply voltage unless otherwise noted. 6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise
Torque Measurement specified.
Mode Torque meter Meter reading
31 to 71 g • cm Tape Signal Used for
FWD CQ-102C (0.43 – 0.98 oz • inch) P-4-A100 10 kHz, –10 dB Azimuth Adjustment
FWD 2 to 6 g • cm
CQ-102C WS-48B 3 kHz, 0 dB Tape Speed Adjustment
back tension (0.02 – 0.08 oz • inch)
31 to 71 g • cm P-4-L300 315 Hz, 0 dB Level Adjustment
REV CQ-102RC
(0.43 – 0.98 oz • inch)
REV 2 to 6 g • cm
CQ-102RC Record/Playback Head Azimuth Adjustment
back tension (0.02 – 0.08 oz • inch)
71 to 143 g • cm (Deck A, Deck B)
FF/REW CQ-201B
(0.98 – 1.99 oz • inch)
100 g or more Note: Perform this adjustments for both decks.
FWD tension CQ-403A
(3.53 oz or more)
100 g or more Procedure:
REV tension CQ-403R
(3.53 oz or more) 1. Mode : Playback
test tape
P-4-A100 main board
(10kHz, –10dB) CN301
Pin 1 (L-CH) level meter
Pin 3 (R-CH)

set +
–
main board
CN301
Pin 2 (GND)

2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.

L-CH
output
peak within
level
1 dB within 1dB

R-CH
peak
screw
position
screw
L-CH R-CH position
peak peak

– 14 –
Downloaded from www.Manualslib.com manuals search engine
 3. Mode: Playback Tape Speed Adjustment (Deck A)
test tape
P-4-A100 main board Note: Set the test mode using the following method and begin tape
(10kHz, –10dB) CN301 speed adjustment.
Pin 1 (L-CH) oscilloscope In the test mode, the speed will switch to double speed or
Pin 2 (GND) normal speed each time the HI-DUB button is pressed.
L

set
Procedure:
With the power turned ON, press the p button, ENTER/NEXT
R
button, and DISC 3 button simultaneously.
(The “VOLUME” on the fluorescent display tube will blink while
Pin 3 (R-CH) in the test mode.)
To exit the test mode, press the 1/u button.

Waveform of oscilloscope 1. Insert the WS-48B into deck B.

2. Press the · button of deck B.
3. Press the HI-DUB button and play the tape at double speed.
4. Adjust RV1001 of the LEAF SW board so that the reading of
in phase 45° 90° 135° 180°
the frequency counter becomes 6000 ± 180 Hz.
good wrong 5. Press the HI-DUB button and play the tape at normal speed.
6. Adjust RV1002 of the LEAF SW board so that the reading of
4. After the adjustments, apply suitable locking compound to the the frequency counter becomes 3000 ± 90 Hz.
parts adjusted.
Adjustment Location: LEAF SW board
Adjustment Location: Playback Head (Deck A)
Record/Playback/Erase Head (Deck B) Sample Value of Wow and flutter
W.RMS (JIS) less than 0.3%
1 Remove the four claws (test tape: WS-48B)

Playback Level Adjustment (Deck A, Deck B)

Procedure:
Mode: Playback
2 Window test tape
P-4-L300 level meter
(315Hz, 0dB)

set

main board
CN301
Pin 1 (L-CH)
Pin 3 (R-CH)

Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301

(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.

Adjustment level:
Reverse Foward
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board

Adjustment Location
[LEAF SW BOARD]

RV1001(High Speed)
RV1002(Normal Speed)

RV1002 RV1001

– 15 –
Downloaded from www.Manualslib.com manuals search engine
 Record Bias Adjustment (Deck B) Record Level Adjustment (Deck B)

Procedure: Procedure:

INTRODUCTION INTRODUCTION
When set to the test mode performed in Tape Speed Adjust- When set to the test mode performed in Tape Speed Adjust-
ment, when the tape is rewound after recording, the “REC memory ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is mode” which rewinds only the recorded portion and playback is
set. set.
This “REC memory mode” is convenient for performing this ad- This “REC memory mode” is convenient for performing this
justment. During recording, the input signal FUNCTION will auto- adjustment. During recording, the input signal FUNCTION will au-
matically switch to VIDEO. tomatically switch to VIDEO.
(After recording, press the – 0 button without stopping will (After recording, press the – 0 button without stopping will
return to the position where recording was started.) return to the position where recording was started.)

1. Press FUNCTION button to select VIDEO. (This step is not 1. Press FUNCTION button to select VIDEO. (This step is not
necessary if the above test mode has already been set.) necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then 2. Insert a tape into deck B, press the r REC button, and then
press the ( button to start recording. press the ( button to start recording.
3. Mode: Record 3. Mode: Record
VIDEO (AUDIO) IN VIDEO (AUDIO) IN
1) 315 Hz 315Hz 50 mV (–23.8 dB)
} 50 mV (–23.8 dB)
2) 10 kHz
AF OSC AF OSC
blank tape blank tape
600 Ω CS-123 600 Ω CS-123
attenuator attenuator

set set

4. Mode: Playback 4. Mode: Playback

recorded level meter recorded level meter
position position

set set

main board main board

CN301 CN301
Pin 1 (L-CH) Pin 1 (L-CH)
Pin 3 (R-CH) Pin 3 (R-CH)

5. Confirm playback the signal recorded in step 2 become adjust- 5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows. ment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH) If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4. and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.

Adjustment level: The playback output of 10 kHz level difference Adjustment level:
against 315 Hz reference should be ± 1.0 dB. CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)

Adjustment Location: AUDIO board Adjustment Location: MAIN board

Adjustment Location: [MAIN BOARD] (Conductor Side)

RV301
[AUDIO BOARD] (Conductor Side) Record Level (Lch)

RV341(Lch),RV441(Rch) RV311(Lch),RV411(Rch)
Record Bias Playback Level (Deck A)
1 3
CN301
IC301
RV301 RV401
RV411
RV441 RV341 RV311 RV351
Record Level (Rch)

RV301(Lch),RV401(Rch)
Playback Level (Deck B)

– 16 –
Downloaded from www.Manualslib.com manuals search engine
 TUNER SECTION 0dB=1µV

Note 1: As a front-end (FE1) is difficult to repair if faulty, replace

it with new one.
Note 2: No adjustment is needed due to a tuner pack for except
AEP, UK, German, East European, CIS models.

AM Tuned Level Adjustment

(AEP, UK, German, East European, CIS model only)
Note: FM Tuned Level adjustment should be performed after this
AM Tuned Level Adjustment.

Setting:
Band: MW
loop antenna
loop antenna (Supplied accessories)

AM RF SSG
set

AM antenna
60cm terminal (TM1)
30% amplitude
modulation by Field strength dB (µV/m) = SSG output level dB (µV/m) –26dB.
400Hz signal

Modulation: 999 kHz (at 9 kHz step)

1,050 kHz (at 10 kHz step)

Procedure: Adjustment Location

1. Set the output of SSG so that the input level of the set becomes [TCB BOARD] (Component Side)
55 dB.
2. Tune the set to 999 kHz or 1,050 kHz.
3. Adjust RV41 to the point (moment) when the TUNED indicator TM1
will change from going off to going on.
RV41
AM Tuner Level
Adjustment Location: TCB board

FM Tuned Level Adjustment

(AEP, UK, German, East European, CIS model only)
Note: This adjustment should be performed after the AM Tuned
Level Adjustment.

Setting:
Band: FM
FM RF SSG RV42
FM Tuned
75 Ω coaxial Level

IC21

set
Carrier frequency: 98MHz
Modulation: AUDIO 1kHz, 75kHz FM ANTENNA terminal (TM1)
deviation (100%)
Output level: 25dB (at 75 Ω open)

Procedure:
1. Supply a 25 dB 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. Adjust RV42 to the point (moment) when the TUNED indicator
will change from going off to going on.

Adjustment Location: TCB board

– 17 –
Downloaded from www.Manualslib.com manuals search engine
 FM Polar Adjustment (East European, CIS model only) Procedure :
1. Set the modulation of FM RF SSG to AUDIO 1 kHz, 10 kHz
Connection 1 : deviation according to “Connection 1”.
2. Tune the set to 69 MHz.
FM RF SSG 3. Adjust the RV1702 so that the reading of frequency counter con-
75 Ω coaxial
nected to TP1702 (VCO) becomes within 31.25 kHz ± 0.05 kHz.
(VCO adjustment)
set
4. Then record the reading of the level meter connected to TP1701.
5. Set the modulation of FM RF SSG to AUDIO 31.25 kHz, 10
FM antenna kHz deviation according to “Connection 2”.
terminal (75 Ω)
6. Tune the set to 69 MHz.
Carrier frequency: 69 MHz
7. Set the CT1701 to be mechanical center.
Output level: 1 mV (60 dBµ) (at 75 Ω open)
Modulation: AUDIO 1 kHz, 10 kHz deviation 8. Adjust the L1701 so that the reading of the level meter con-
nected to TP1701 (FILTER) becomes maximum.
Connection 2 : Then adjust the CT1701 so that the reading of the level meter
connected to TP1701 (FILTER) becomes maximum. (SUB CAR-
AF OSC
FM RF SSG
RIER PEAK Adjustment)
75 Ω coaxial 9. Adjust the RV1701 so that the level at the moment becomes 14
dB higher value than the level recorded in step 4. (SUB CAR-
set RIER LEVEL Adjustment)

Audio 31.25 kHz FM antenna

external
modulation terminal (75 Ω)
terminal
Carrier frequency: 69 MHz
Output level: 1 mV (60 dBµ) (at 75 Ω open)
Modulation: AUDIO 31.25 kHz, 10 kHz deviation
(EXTERNAL MODULATION)

Adjustment Location: TCB board

Adjustment Location:

[TCB BOARD] (Conductor Side) [TCB BOARD] (Component Side)

L1701
CT1701 Sub Carrier Peak

frequency counter
RV1701
Sub Carrier
TP1701
Level
(FILTER)

level meter
IC1701 IC1701

TP1702
(VCO) RV1702
VCO

– 18 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 7
DIAGRAMS
E-F Balance (Traverse) Check 7-1. CIRCUIT BOARDS LOCATION
CD SECTION
oscilloscope TRANSFORMER board
Note: BD board
1. CD Block is basically constructed to operate without adjustment. LEAF SW board
Therefore, check each item in order given. TP (TE) +
TP (VC) – SURROUND board
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when Procedure :
the signal level is low than specified value with the following 1. Connect oscilloscpe to test point TP (TEO) on BD board. AUDIO board
checks. 2. Turned Power switch on. Press FUNCTION button to select
CD.
S Curve Check 3. Put disc (YEDS-18) in to play the number five track.
oscilloscope 4. Press the p button, ENTER/NEXT button and ^ button
BD board simultaneously several times until the ‘’SHUFFLE” on the
fluorescent display tube blinks. MAIN board
TP (FEO) + (The sledding servo is turned OFF.)
TP (VC) – 5. Check the level B of the oscilliscope’s waveform and the A (DC
voltage) of the center of the Traverse waveform.
Confirm the following :
Procedure : A/B x 100 = less than ± 7%
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and Ground by lead wire. CONT (COM) board
Traverse waveform CD-SW board
3. Turn Power switch on. Center of the waveform
4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc B
table is moving in and out.)
A (DC voltage) POWER board
5. Check the oscilloscope waveform (S-curve) is symmetrical be- 0V
tween A and B. And confirm peak to peak level within 3 ± 1Vp-p.
DECO board
S-curve waveform level : 500 mV ± 100 mVp-p
symmetry
6. Press the p button, ENTER/NEXT button and ^ button
simultaneously several times until the ‘’SHUFFLE” on the
fluorescent display tube goes off. (The tracking servo and TUNER(FM/AM)
A (EXCEPT AEP,UK,German,
sledding servo are turned ON.) Confirm the C (DC voltage) is
Within 3 ± 1 Vp-p East European,CIS)
almost equal to the A (DC voltage) is step 5. MIC board
B
TCB board
Traverse waveform (AEP,UK,German,
East European,CIS)
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7. C (DC
0V voltage)
• Take sweep time as long as possible and light up the bright-
ness to obtain best waveform.
PANEL board
Sled servo Sled servo
RF Level Check OFF ON HP board
oscilloscope
MOTOR (TURN) board
Adjustment Location : CONNECTOR board
BD board

TP (RF) + [ BD BOARD ] — SIDE A — BD board

TP (VC) –
TP (RF) TP
(VC)
Procedure : TP
1. Connect oscilloscope to test point TP (RF) on BD board. (FOK)
CN101

SENSOR board
IC101
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF sig- TP
IC102
(TEO)
nal level is correct or not.
TP
Note: Clear RF signal waveform means that the shape “◊” can be (FEO) MOTOR (SLIDE) board
clearly distinguished at the center of the waveform. TP
(GND)
RF signal waveform IC103
VOLT/DIV : 200mV
TIME/DIV : 500ns

level : 1.3 ± 0.3 Vp-p

IC102

– 19 – – 20 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-2. BLOCK DIAGRAMS

– TUNER SECTION – (AEP, UK, German model)

ST +10V

Q5
FE1
TM1 FM FRONT END
ANTENNA CF1 CF2 CF3
10.7MHz IF AMP 10.7MHz IF AMP 10.7MHz AMP
FM 75Ω ANT IN 1 FM IN 22 MPX IN OUT L 21 LPF 19 AMP IN L OUT 17
IF OUT Q1, 2 Q3, 4 FM DET OUT 23
COAXIAL L
OUT R 20 RCH
VT

AM

FM/AM MPX RDS DECODER

IC41 IC1751 IC1752
FE2
MW/LW FRONTEND 4 2
5 7
16

6 12 28 REG 13 14
LW SW
Q9
5 13
X1751
4.332MHz
14
3 15

16
2 AM
AM IF ST L
AM MIX 2
IFT41
4 AM IF DET 24
OUT RDS INT • R CH: Same as L ch
17 29 AM X41 RDS DATA
AM OSC • SIGNAL PATH
SD 12 10.7MHz
ADJ FM STEREO 7 STEREO
26 25 24 23 22 21 20 9 DET
26 FM AFC
RV41
TUNED 6 TUNED : FM
AM : MW
27 AM RF IN TUNED
VCO STOP

LEVEL
OSC.BUFF

IF BUFF
MUTE
AM/FM
FM SD

Q14 AM
ADJ

LW SW 10
SD
Q11 30 14 15 13 X42
Q12 MW 450kHz
Q13
MW
SW
MW
SW
SW RV42
FM MUTE A
TUNED D41
LEVEL MAIN
SECTION
(Page 29)
X21
4.5MHz
10 17 9 11 14 7 2 12 1 24
3 ST-CE
MW

CE
FM

VT1

MW

AM OSC

FM
VCO STOP
FM/AM IF

XIN
XOUT

PLL DI 4 COM-DIN
IC21 CL 5 COM-CLK
DO 6 COM-DATA

09

– 21 – – 22 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

– TUNER SECTION – (East European, CIS model)

ST +10V

Q5
FE1
TM1 FM FRONT END
ANTENNA CF1 CF3
10.7MHz IF AMP 10.7MHz
FM 75Ω ANT IN 1 FM IN 22 MPX IN OUT R 20 RCH
IF OUT Q1-4 FM DET OUT 23 AMP
COAXIAL OUT L 21 LPF 19 IN AMP
L OUT 17
L
VT

AM POLAR/PILOT
SWITCH
IC1702
FM/AM MPX SUB CARRIER
IC41 PEAK POLAR
FE2 DECODER
12 L IN
MW/LW FRONTEND IC1701
L OUT 14
CT1701 L1701
TP1701
6 12 28 REG 2 IN L OUT 7 13 POLA
LW SW L IN • R CH: Same as L ch
Q9
5 13 • SIGNAL PATH
3 POUT R OUT 6 R CH
R OUT 4 R CH : FM
14 : MW
C A
3 15
9 11

ST IND

STOP
MON

VCO

VCO
16
2 AM
AM IF 20 SUB IN
AM MIX 2
IFT41 4 AM IF DET 24
OUT 18 17 10 9
AM X41 SWITCH
17 29 AM OSC RV1701
SD 12 10.7MHz Q1701
STEREO 7 SUB CARRIER
26 25 24 23 22 21 20 ADJ RV41 9 FM D1701
26 FM AFC DET TUNED 6 LEVEL TP1702
AM RV1702
D1702
TUNED VCO
27 AM RF IN
VCO STOP

LEVEL
OSC.BUFF

IF BUFF
MUTE
AM/FM

SWITCH SWITCH
FM SD

Q14 AM Q1702 Q1703

ADJ

LW SW 10
SD
Q11 30 14 15 13 X42
Q12 MW 450kHz D1703
Q13 MW
MW SW RV42
SW ST-L
SW FM D41
TUNED STEREO
LEVEL TUNED
D42 D43
MUTE

X21
4.5MHz D1704
A
10 17 9 11 14 7 2 12 8 1 24 13 MAIN
SECTION
MW

CE 3
FM

VT1

MW

ST-CE
AM OSC

FM
VCO STOP
FM/AM IF
IF REQ

XIN
XOUT

FM LOW

PLL DI 4 COM-DIN (Page 29)

IC21 CL 5 COM-CLK
DO 6 COM-DATA

09

– 23 – – 24 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

– CD SECTION –

IC391

1 D.OUT CD DIGITAL
OUT X101
OPTICAL 16.9344MHz
OPTICAL PICK-UP BLOCK
FOCUS/TRACKING SERVO.
RF AMP
71 89 • 90
IC101 (1/2)
B+

XTAO
DOUT

XTAI
DETECTOR K

•
E
1
A
4 38 PD1 RF O 33 44 RF LOUT1 86 L-CH
A D 2 39 PD2
D DIGITAL SIGNAL PROCESSOR
5 LOCK 19 29 LOCK IC103 LOUT2 93 R-CH
B C 10 41 F C.OUT 24 14 CNIN
C
6 42 E SENS1 25 15 SEIN

B
DATAO

CLOK
SPOD
CLKO

SQCK
SCOR
SQSO

SENS
XLTO

XRST
DATA
XLAT
MDP
FOK

F
SENS2 26
15 16 17 27 23 21 10 11 12 75 8 7 9 100
2 FEI

FE O 6 S101
1 FEO
FE M 7 LIMIT
45 TEO
CD CLK
TA M 12
47 TEI
TA O 13 CD DATA
SENS2
DATA 22
XLT 21
CLK 20 SCOR
SQ DATA
LD DRIVE 36 LD FOK 27 SQ CLK
Q101
SENS
LASER 37 PD
DIODE
XRST
23

XRST

FOCUS
COIL
TRACKING
COIL
9
MUTE
XLAT
C
T+ MAIN
15 TRACKING TABLE
27 SENSOR SECTION
16 COIL DRIVE T. SENS
IC702 (Page 29)
T–
FOCUS/TRACKING
2-AXIS COIL DRIVE
IC102 (1/2) DISC
DEVICE SENSOR DISC SENS
F– IC703
18 FOCUS Q701
F+ COIL DRIVE 26
17
ROTARY ENC 1
ENCODER ENC 2
S811
ENC 3

SLED/SPINDLE SLED TURN S801

MOTOR DRIVE SERVO MOTOR DRIVER OPEN/CLOSE OPEN
IC102 (2/2) IC101 (2/2) IC701 DET

11 M701 7 OUT1 IN1 3 TBL.L

M102 SLED MOTOR
M • 6 16 SL O SL P 14 TURN M
SLED MOTOR DRIVE 2 OUT2 IN2 6 TBL.R
12 MOTOR

SLIDE
MOTOR DRIVER
IC801 • R CH: Same as L ch
M101 13
• SIGNAL PATH
SPINDLE MOTOR M801
SPINDLE M 3
• DRIVE SLIDE 4 OUT2 RIN 2 LOAD IN : CD
MOTOR 14 M 7
MOTOR OUT1 FIN 10 LOAD OUT
: Digital out
09

– 25 – – 26 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

– DECK SECTION –

PB A/B
S1004 S1008
A CrO2 B CrO2 MS OUT

CN301
3 R CH
RV311
16 17 19 28 27 26
PLAYBACK 1
IC611 PB-A/B A 120/70 B 120/70
LEVEL MS
DECK A
L 70
A IN PAS
48 PB OUT
HP101 B IN 40 PB L
46 120
PB HEAD R CH DOL LM ON/ 25
(DECK A) R LM ON/OFF
DOLBY NR OFF
DOLBY NR
NORM/
RV301 IC301
HIGH 18 NORM/HIGH
PLAYBACK NR ON/
IC601 NR ON/OFF
LEVEL OFF 23
DECK B
L 24 REC/PB/PASS
RV301
PB
REC/PB HEAD REC LEVEL
(DECK B) RECOUT DOLBY
39 RIN
R R CH TYPE B 44 REC L

EQOUT EQIN BIAS ON/OFF

36 38 BIAS SW 20 BIAS ON/OFF
RM ON/OFF 22 RM ON/OFF
ALC ON/OFF 15 ALC ON/OFF
M

1
C

3
IC602 32 33
P R
4 RELAY REC/PB
HRPE101 REC/PB CAPM CNT1M
CAP MOTOR
RV341 CONTROL CAPM CNT2M
REC Q336-343
BIAS +7.5V CAPM CNT1P
Q623 CAPM CNT2P
M1 SPEED
SWITCH
CAPSTAN M CONTROL CAP M H / L
Q335
MOTOR

ERASE BIAS
REC BIAS
BIAS OSC
T621, Q621, 622
Q1001
B
ERASE HEAD X MAIN
SECTION
RV1002 RV1001
REEL (Page 29)
NORMAL HIGH
DETECT A SHUT
SPEED SPEED
IC1001

REEL
DETECT B SHUT
IC1002

S1001 (A PLAY)
• R CH : Same as L ch +5V A PLAY
• SIGNAL PATH S1002 (B PLAY)
B PLAY
: PB (DECK A)
: PB (DECK B) S1003
(A HALF) +5V
: REC (DECK B)
+5V

S1005
(REC A)
09 S1006 B HALF
(B HALF)

S1009
(REC B)

• PLUNGER SOLENOID is supplied

as the MECHANICAL BLOCK ASSY.
TRIGGER B TRIG
A DECK/
MOTOR
B DECK
CONTROL
PLUNGER A TRIG
Q331-334

– 27 – – 28 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

– MAIN SECTION –
RV750
MIC
PRO IN G
J751 LEVEL PRO OUT
POWER
MIX R-CH MIX AMP SECTION
MIC IC401
IC750(1/2) (Page 31)
6 7
(Page 34) SPE SIG
IC750(2/2)
DISPLAY

E
IC411(1/2) IC411(2/2)
SECTION
3 1 MUTE 6 7 IIC DATA
DJ-SIG
Q411
F DJ-MUTE EQ
IC111(1/2)
VOLUME
IC111(2/2)
IIC CLK DISPLAY
SECTION
2 RESET (Page 33)
J101
VIDEO IN EQ MUTE
(AUDIO) V AMP 42 41 36 FRONT
64 Q113
L MD
69
TC SELECT
MD IN L 67 SWITCH 60
TU AMP J191
66 & 59
68 CD SW 58 MUTE SUPER
R-CH 40 6 1
Q191 WOOFER
57
MD/VIDEO
(AUDIO) TA MUTE
MICON 38 39 SUPER WOOFER
OUT L INTERFACE AMP DBFB
IC191 SWITCH
34 33 32 Q141,143
1 2 3
DBFB DBFB
PB L SWITCH
REC L Q111,112

RELAY REC/PB 97 TC RELAY

A SHUT 26 A SHUT
B SHUT 27 B SHUT DBFB H/L 2
B HALF 28 B HALF TA MUTE 1
A HALF 98 A HALF
A PLAY 95 A PLAY SW F RELAY 6 F RELAY

B B PLAY
PB A / B
NORM/HIGH
96
87
93
B PLAY SW
PB A/B
EQ H//N
PL RELAY 8 PL RELAY

DECK BIAS ON/OFF 92 BIAS

SECTION RM ON/OFF 90 REC MUTE
IIC DATA 55
(Page 28) NR ON/OFF 89 NR ON/OFF
REC/PB PASS
CAPM CNT1M
88
85
R/P PASS
CAPM CNT1M
IIC CLK 56
D
CAPM CNT2M 86 CAPM CNT2M POWER
RESET 15
CAPM CNT1P 17 CAPM CNT1P SECTION
CAPM CNT2P 77 CAPM CNT2P (Page 31)
EXCEPT AEP, UK, ALC ON/OFF 99 ALC ON/OFF RESET
G, EE, CIS LM ON/OFF 87 TC MUTE SWITCH
CAP M H/L 82 CAP M H/L Q951
FM/AM TUNER
A TRG 83 A TRG
TUNER UNIT IS
B TRG 84 B TRG AC CUT 16
SUPPLIED AS
MS OUT 31 AMS IN MASTER CONTROL
THE ASSEMBLED 1
ST L 3 M62442 LAT IC501
BLOCK 2 RESET
RDS DATA 52 M62442 DATA
3 IC951
RDS INT 51 M62442 CLK
COM DIN

A COM DATA 66 ST DIN

D951
STEREO 70 STEREO
TUNED 69 TUNED
+5V
TUNER ST CE 68 ST CE
SECTION X1 11
MUTE 72 ST MUTE X501
(Page 22, 24) COM CLK 67 ST DOUT 5MHz
X2 10
AEP, UK, G, EE, CIS L CH 65 ST CLK
TBL. L 60 TBL L
TBL. R 61 TBL R XT1 14
SCOR 18 SCOR X502
32.768KHz
T. SENS 76 T SENS XT2 13 • R CH: Same as L ch
SENS 2 73 SENS 2
SENS 74 SENS
PL-DATA 50 PL-DATA • SIGNAL PATH
PL-CLK 49 PL-CLK
X RST 57 XRST : FM
C CD CLK
CD DATA
48
47
CD CLK
CD DATA
PL-LAT
PL-VOL
42
41
PL-LAT
PL-VOL : CD
CD DISC SENS 75 DISC SENS POWER 5 POWER ON/OFF : PB
SECTION SQ CLK 36 SQ CLK : REC
(Page 26) SQ DATA 34 SQ DATA IN CD POWER 46 CD POWER
X LAT 58 XLT
: VIDEO/MD
OPEN 81 OUT OPEN • Abbreviation
ENC-1 80 ENC1 G : German model.
ENC-2 79 ENC2
ENC-3 78 ENC3 MUTE EE : East European model.
LOAD IN 64 LOAD IN STK MUTE 100 SWITCH STK MUTE
Q142
LOAD OUT 63 LOAD OUT
RX110AV:
22 RDS DATA
09 AEP,UK,G
21 RDS INT

– 29 – – 30 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV
– POWER SECTION –
PRO OUT
DOLBY
PRO LOGIC

G SURROUND
PROCESSOR
IC201
MAIN TM402
SECTION PRO IN 61 LT IN L OUT 24 AMP POWER AMP SURROUND
R -CH 62 RT IN R OUT 21 R -CH IC291 IC601 SPEAKER
(Page 30)
MUTE 5 7
C OP 31 1 10
51 DATA Q291 CENTER
PL-DATA OUT
53 DATA
PL-CLK 50 CLK
REAR
54 CLK MUTE 3 1 RELAY
S OP 33 18 13
PL-LAT 52 ENABLE Q292 DRIVE
OUT
PL-VOL 49 ENABLE2 OVER Q404-406
RY403
LOAD
OSC OSC
DET
46 47 Q601,604,651

X201 8MHz FAN MOTOR M901

DRIVER M FAN
TA MUTE UNREG
Q961, 962 MOTOR
PL RELAY –12V
Rch
F RELAY

THERMAL TM401
POWER AMP DET
FRONT
IC201 Q321,322
SPEAKER
THP321
RY401 FRONT
FRONT 3 12
FRONT 8 RELAY
DRIVE
J755
Q401,402
PHONES

OVER LOAD
DET
Q201 Rch

Rch
Rch

DBFB PROTECT
CONTROL
Q301-303,
Rch Q306,307
MUTE

D
STK MUTE SWITCH
D5V Q304,305
SWITCHED
MAIN CD REG
SECTION CD+5V
Q931
+5.6V
(Page 30)
+5.6V REG
IC931
CD POWER Q932 D932
3 1

+7V REG
IC941
+5V REG M+7V
AU/D5V SW 3 1 T501
Q933
POWER
TRANSFORMER
VF
+7V REG
Q934
IC901
VF
A+7V 3 1
RECT
SWITCH +12V REG
Q901 –7V REG D103,
Q911-913
IC902 D104

A–7V
Q905
3 2 • R CH : Same as L ch
Q937 • SIGNAL PATH
GRX10AV:E2,E3,SP,MY,HK,EA
: FM
UNREG VF REG RECT
VFDP Q111 D111,112
VOLTAGE • Abbreviation
–12V SELECTOR
S501 CND :Canadian model
RECT
+10V REG
D102 E2 : Without SW tuner E model.
IC911
GRX10AV/RX110AV:CND
E3 : Without SW tuner E model.
+10V 3 1 POWER B+ RECT
POWER B– D101 EA : Saudi Arabia model.
AC SP : Singapore model.
ST+10V 3 1 IN
MY : Malaysia model.
+10V REG HK : Hong Kong model.
IC921
RELAY
POWER ON/OFF +7V DRIVER
G : German model.
Q101 RY101 EE :East European model.
09
RX110AV:AEP,UK,G,EE,CIS
– 31 – – 32 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

– DISPLAY SECTION –

LED1 79
•
80
• Q601,602
1 LED
IIC DATA 24 SDA PANEL LED D+5V
6 SWITCH
IIC CLK 23 SCL •
11
•
12
•
14
LED15 18
LED PANEL CONTROL
L SEL 25 CONTROL IC801
Q603

REMOTE 19 I2C DATA

DISPLAY CONTROL SIRCS 33 CONTROL 18 I2C CLK S801-808
RESET 10 RESET IC601 RECEIVER
SPEANA 1 34 4 RESET KEY O 38 KEY
IC602
SPEANA 2 35 KEY 1 39 MATRIX
29 SIRCS
SPEANA 3 36
SPEANA 4 37 S601
D801-803
L+R 32 (JOG)
JOG A 21 ROTARY 61 LED
BPM LED B
22 ENCODER SWITCH
JOG B BPM LED A 62
Q854,855
27 JOG A
28 JOG B
KEY 0 26
8 XOUT KEY
X601 MATRIX BOMBER LED 63 PANEL LED
8MHz KEY 3 29

E 9 XIN ON/OFF LED 64

D805 D806

MAIN
SECTION SPEANA
CONTROL
(Page 30) 2 XOUT Q958-960
S602 X501
VOLUME 8MHz MUTE
3 XIN MUTE 5 SWITCH DJ MUTE
VOL A 19 ROTARY Q851
VOL B 20 ENCODER
SEG1-SEG20 GR1-GR13 SOUND MIX
IC851
54 - 57 41 - 53

DATA 14 15 SD
F
FL601,Q70,702 SP1 CLK 15 14 SI MAIN
VF 33 BPF LOW
FLUORESCENT INDICATOR TUBE SP4 LAT 16 8 ST SECTION
36 BPF HIGHT OUT 23 DJ SIG
L+R
37 L+R
CH 13 16 CH (Page 29)
RST 12 17 RST
SPEANA BPF FILTER
IC603 BSY 20 20 BUSY
XT XT
2 3
SP1
F01 17
SP2
F02 16 X851
4 LINE IN SP3
SPE SIG F03 15 4.09MHz
SP4
F04 14
L+R
L+R 13

09

– 33 – – 34 –

Downloaded from www.Manualslib.com manuals search engine

 WAVEFORMS
THIS NOTE IS COMMON FOR PRINTED WIRING – TUNER SECTION – – DISPLAY SECTION –
– CD SECTION –
BOARDS AND SCHEMATIC DIAGRAMS.
(AEP, UK, German model)
(In addition to this, the necessary note is printed 1 1
in each block.) 1
1.3Vp-p 4Vp-p
For schematic diagrams. 4.2Vp-p
Note: 8MHz
• All capacitors are in µF unless otherwise noted. pF: µµF 500mV/DIV, 500nsec/DIV
IC101 #£ RFO IC601 8 X-OUT
50 WV or less are not indicated except for electrolytics 4.5MHz
IC21 @¢ XOUT
and tantalums.
2 2
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified. 2
4.3Vp-p
• ¢ : internal component. 0.5Vp-p

• C : panel designation. 2Vp-p

8MHz
Note: Note: 200mV/DIV, 1µsec/DIV
The components identi- Les composants identifiés par IC101 2 FEI 4.332MHz IC801 2 X-OUT
fied by mark ! or dotted une marque ! sont critiques IC1752 !¢ OEC O
line with mark ! are criti- pour la sécurité. 3 3
cal for safety. Ne les remplacer que par une
0.2Vp-p 3.6Vp-p
Replace only with part piéce por tant le numéro
number specified. spécifié. – TUNER SECTION –
50mV/DIV, 1msec/DIV 4.09MHz
• U : B+ Line. (East European, CIS model)
IC101 $¶ TEI IC851 2 TX
• V : B– Line.
• H : adjustment for repair. 1
• Voltages and waveforms are dc with respect to ground 4
7.8µsec
under no-signal (detuned) conditions. 4.2Vp-p
• Voltages are taken with a VOM (Input impedance 10 MΩ).
2.5Vp-p
Voltage variations may be noted due to normal produc- 4.5MHz
tion tolerances.
IC21 @¢ XOUT
• Waveforms are taken with a oscilloscope. IC103 @¶ MDP
Voltage variations may be noted due to normal pro-
duction tolerances. 5 230µsec
• Circled numbers refer to waveforms.
• Signal path. – MAIN SECTION –
5Vp-p
F : FM
f : AM 1
g : VIDEO/MD
E : PB (DECK A) IC103 ^º XPCK
5.5Vp-p
d : PB (DECK B) 6
G : REC (DECK B) 135µsec
5MHz
J : CD
IC501 0 X2
c : digital out 5Vp-p
• Abbreviation 2
CND : Canadian model.
G : German model. IC103 ^™ RFCK 5Vp-p
E2 : Without SW tuner E model.
E3 : With SW tuner E model. 7 32.768kHz
135µsec
EA : Saudi Arabia model.
EE : East European model. IC501 !£ XT2
AUS : Australian model. 5Vp-p
SP : Singapore model. 3
MY : Malaysia model.
IC103 &¢ WFCK
HK : Hong Kong model. 4.5Vp-p
TH : Thai model.
8
8MHz
For printed wiring boards. 2.6Vp-p IC201 $¶ OSC
Note:
• X : parts extracted from the component side.
• p : parts mounted on the conductor side. 16.9344MHz

• ® : Through hole. IC103 *ª XTAI

• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)

– 35 – – 36 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-3. PRINTED WIRING BOARD — CD SECTION —

• See page 20 for Circuit Boards Location.

• Semiconductor
Location
Ref. No. Location
IC101 C-5
IC102 B-5
IC103 C-6

Q101 C-3

(Page 52)

• Indication of transistor

C
Q These are omitted
B E

– 37 – – 38 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-4. SCHEMATIC DIAGRAM — CD SECTION —

• See page 35 for Waveforms.
• See page 86 for IC Block Diagrams.
• See page 90 for IC Pin Functions.

(Page
56)

– 39 – – 40 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-5. SCHEMATIC DIAGRAM – TUNER SECTION – (AEP, UK, German model)

• See page 36 for Waveforms.
• See page 84 for IC Block Diagrams.

(Page 53)

– 41 – – 42 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX10AV

7-6. PRINTED WIRING BOARD – TUNER SECTION – (AEP, UK, German model)
• See page 20 for Circuit Boards Location.

• Semiconductor
Location
Ref. No. Location
D21 D-1
D41 D-2
D42 E-3
D1751 F-2

IC21 D-1
IC41 C-3
IC1751 E-1
IC1752 F-3

Q1 D-1
Q2 D-1
Q3 C-2
Q4 C-2
Q5 C-2
Q9 B-1
Q11 B-3
Q12 A-3
Q13 A-2
Q14 A-2

(Page 52)

• Indication of transistor
C
Q These are omitted
B E

– 43 –
Downloaded from www.Manualslib.com manuals search engine
 HCD-GRX10AV/RX110AV

7-7. PRINTED WIRING BOARD – TUNER SECTION – (East European, CIS model)
• See page 20 for Circuit Boards Location.

• Semiconductor
Location
Ref. No. Location
D1 D-1
D41 D-2
D42 E-3
D43 E-3
D1701 F-2
D1702 F-2
D1703 E-2
D1704 F-2

IC21 D-1
IC41 C-3
IC1701 F-1
IC1702 F-3

Q1 D-1
Q2 D-2
Q3 C-2
Q4 C-2
Q5 C-2
Q9 B-1
Q11 B-3
Q12 A-3
Q13 A-2
Q14 A-2
Q1701 E-2
Q1702 F-2
Q1703 F-2

• Indication of transistor
C
Q These are omitted
B E

(Page 52)

– 44 –
Downloaded from www.Manualslib.com manuals search engine
 HCD-GRX10AV/RX110AV

7-8. SCHEMATIC DIAGRAM – TUNER SECTION – (East European, CIS model)

• See page 36 for Waveforms.
• See page 84 for IC Block Diagrams.

(Page 53)

– 45 – – 46 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-9. SCHEMATIC DIAGRAM – DECK SECTION –

• See page 89 for IC Block Diagrams.

(Page 54)

– 47 – – 48 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-10. PRINTED WIRING BOARD – DECK SECTION –

• See page 20 for Circuit Boards Location.

(Page 51)

• Indication of transistor

BC E
These are omitted

– 49 – – 50 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV
• Indication of transistor
C
7-11. PRINTED WIRING BOARD – MAIN SECTION –
Q These are omitted
• See page 20 for Circuit Boards Location. BC E
• Semiconductor B E These are omitted
Location
Ref. No. Location
(Page 81) (Page 81) (Page 38)
D381 B-10
D382 B-10 (Page 43, 44)
D502 C-3
D508 B-1
D901 G-2
(Page 70)
D921 J-3
D931 H-3
D932 F-3
D951 D-6
D952 D-6
D953 D-5
D954 D-5
D955 D-6
D956 D-5

IC111 D-10
IC191 E-11
IC201 G-10
IC291 F-7 (Page 49)
IC301 D-3
IC391 B-12
IC401 G-7
IC411 H-7
IC501 C-5
IC901 F-2
IC902 G-2
IC911 H-3
IC921 H-2
IC931 G-3
IC941 G-5
IC951 D-6

Q111 E-8
Q112 E-8
Q113 E-9
(Page 83)
Q141 I-6
Q142 I-7
Q143 H-1
Q161 D-8 (Page 71)
Q162 D-8
Q163 E-8
Q191 E-12
Q291 F-7
Q292 G-7
Q331 B-3
Q332 B-3
Q333 B-2
Q334 B-2
Q335 B-3
Q336 A-1
Q337 A-1
Q338 B-1
Q339 B-1
Q340 A-2
Q341 A-2
Q342 B-1
Q343 B-2
Q411 H-6
Q901 G-2
Q902 F-2
Q903 H-2
Q904 G-2
Q905 G-2
Q911 I-4
Q912 H-3
Q913 H-3
Q931 F-2
(Page 63)
Q932 E-2
Q933 F-2
Q934 F-2
Q937 F-2 (Page 63)
Q951 D-5
Q961 I-11
Q962 I-11

– 51 – – 52 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-12. SCHEMATIC DIAGRAM – MAIN (1/4) SECTION –

(Page 41, 45)

(Page 70)
(Page 48)

(Page
55)

(Page 55)

(Page 59)

(Page 59)

(Page 55)

(Page 57) (Page 57) (Page 59)

– 53 – – 54 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-13. SCHEMATIC DIAGRAM – MAIN (2/4) SECTION –

• See page 36 for Waveforms.
• See page 51 for Printed Wiring Board.
• See page 95 for IC Pin Functions.

(Page 54)

(Page 40)

(Page 54) (Page 80)

(Page 80)

(Page 54)

(Page 59) (Page 59) (Page 60) (Page 60)

– 55 – – 56 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-14. SCHEMATIC DIAGRAM – MAIN (3/4) SECTION –

• See page 51 for Printed Wiring Board.
• See page 88 for IC Block Diagrams.

(Page 53) (Page 53)

(Page 59)

(Page 59)

(Page 59)

DOLBY PRO LOGIC

PROCESSOR

(Page 83)

– 57 – – 58 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-15. SCHEMATIC DIAGRAM – MAIN (4/4) SECTION –

• See page 51 for Printed Wiring Board.

(Page 55) (Page 55) (Page 55) (Page 56)

(Page 54)

(Page
54)

(Page
54)

(Page
58)

(Page
58)

(Page
58)

(Page 73) (Page 65) (Page 65)

– 59 – – 60 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-16. SCHEMATIC DIAGRAM – MIC/HP SECTION – 7-17. PRINTED WIRING BOARD – MIC/HP SECTION –
• See page 20 for Circuit Boards Location.

(Page 64)

(Page 65)

MIX MIC

(Page 65)

11
12

(Page 63)
11
12

– 61 – – 62 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-18. PRINTED WIRING BOARD – POWER SECTION –

• See page 20 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location

D101 H-6
D102 H-1
D103 I-5
D104 I-5
D105 H-7
D111 I-3
D112 I-4
D113 I-3
D114 I-3
D201 F-5
D251 F-4
D301 H-9
D311 G-3
D321 I-5
D331 H-3
D332 H-3
D401 C-2
D403 F-7
D405 B-2
D406 B-1
D407 B-4
D408 B-4

IC201 D-5

Q101 H-7
Q111 I-3
Q201 F-5
Q251 F-3
Q301 H-8
Q302 G-7
Q303 H-7
Q304 G-8
Q305 G-7
Q306 G-8
Q307 G-8
Q321 F-3
Q322 E-3
Q401 D-2
Q402 D-1
Q404 G-6
Q405 F-6
Q406 F-6

(Page 83)
(Page 52)

• Indication of transistor

BC E
These are omitted

(Page 69)
(Page 51)

(Page 62)
(Page 62)

– 63 – – 64 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-19. SCHEMATIC DIAGRAM – POWER SECTION –

(Page 61)
(Page 67)

(Page
60)
(Page 67)

(Page
61)

(Page 67)

(Page (Page 67)

60)

(Page 67)

– 65 – – 66 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-20. SCHEMATIC DIAGRAM – TRANSFORMER SECTION –

• See page 63 for Printed Wiring Board. (POWER BOARD)

(Page 66)

(Page 66)

(Page 66)

(Page 66)

(Page
83)

(Page
66)

– 67 – – 68 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-21. PRINTED WIRING BOARD – TRANSFORMER SECTION – 7-22. PRINTED WIRING BOARD – LEAF SW SECTION –
• See page 20 for Circuit Boards Location. • See page 20 for Circuit Boards Location.

• Indication of transistor
(Page 51)

BC E
These are omitted

7-23. SCHEMATIC DIAGRAM – LEAF SW SECTION –

(Page 64) (Page 54)

– 69 – – 70 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-24. PRINTED WIRING BOARD – DISPLAY SECTION –

• See page 20 for Circuit Boards Location.

• Semiconductor
Location
Ref. No. Location
D601 D-2
D602 D-4
D603 D-4
D620 C-10
D621 C-4
D622 C-5
D623 C-6
D624 C-7
D625 C-8
D629 C-3
D630 C-2
D651 E-1
D652 E-1
D804 I-17
D805 E-6
D806 E-5
D807 E-9

IC601 B-5
IC602 A-9
IC603 B-7
IC801 E-7
IC851 E-5
(Page 51)
Q601 D-1
Q602 C-1
Q603 C-2
Q607 C-9
Q608 C-4
Q609 C-6
Q610 C-8
Q618 E-2 (Page 78)
Q701 A-6
Q702 A-8
Q851 F-6
Q958 E-9
Q959 E-8
Q960 E-8 (Page 78)

11
12

(Page 77)

• Indication of transistor
C
Q These are omitted
B E

– 71 – – 72 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-25. SCHEMATIC DIAGRAM – DISPLAY SECTION –

• See page 36 for Waveforms.
• See page 89 for IC Block Diagrams.
• See page 98 for IC Pin Functions.

(Page 75)

(Page
59)

(Page 75)

(Page 76)

– 73 – – 74 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-26. SCHEMATIC DIAGRAM – PANEL SECTION –

(Page 74)

(Page 73)

(Page 74)

– 75 – – 76 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-27. PRINTED WIRING BOARD – PANEL SECTION –

• See page 20 for Circuit Boards Location.

• Semiconductor
Location
Ref. No. Location
D610 A-3
D612 B-2
D613 A-4
D614 C-5
D615 C-4
D616 A-6
D617 B-6
D618 B-3
D801 C-8
D802 C-6
D803 C-5

Q604 B-2
Q854 C-5
Q855 C-5

• Indication of transistor
C
Q These are omitted
(Page 71) 11 B E

12

( )

(Page 72)

11
12

11
(Page 72)
12

– 77 – – 78 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-28. SCHEMATIC DIAGRAM – CD MOTOR SECTION –

• See page 89 for IC Block Diagrams.

(Page 56)

(Page 56)

– 79 – – 80 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-29. PRINTED WIRING BOARD – CD MOTOR SECTION –

• See page 20 for Circuit Boards Location.

(Page 52)

(Page 52) • Indication of transistor

BC E
These are omitted

– 81 – – 82 –

Downloaded from www.Manualslib.com manuals search engine

 HCD-GRX10AV/RX110AV

7-30. SCHEMATIC DIAGRAM – SURROUND SECTION – 7-32. IC BLOCK DIAGRAMS

• Tuner section

IC21 LC72130

AOUT2

AOUT1
XOUT

AMIN
FMIN
AIN2

AIN1

VDD
VSS

PD2

PD1

IO2
24 23 22 21 20 19 18 17 16 15 14 13

PHASE DETECTOR
CHARGE PUMP

UNLOCK POWER
DETECTOR ON 1/2
RESET
REFERENCE SWALLOW COUNTER
DIVIDER 1/16, 1/17 4BITS

12BITS PROGRAMMABLE
DRIVER

(Page 57)

(Page 67)
C2B UNIVERSAL
I/F DATA SHIFT REGISTER LATCH
COUNTER

1 2 3 4 5 6 7 8 9 10 11 12
XIN
BO5
CE
D1
CL
D0

BO1

BO2

BO3

BO4

IO1

IFIN
IC41 LA1838
AM-DET OUT

FM-DET OUT

AMP OUT R
AMP OUT L
FM-SD.ADJ
OSC.BUFF

AMP-IN R
AM-RF-IN

AMP-IN L
AM-OSC

FM-AFC

MPX-IN

OUT R
OUT L
REG

AGC

7-31. PRINTED WIRING BOARD – SURROUND SECTION –

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
• See page 20 for Circuit Boards Location. REG

ALC AM AM AM DECODER
OSC MIX RF. AMP ANTI BIRDIE
BUFF
STEREO
AGC SW
SD
COMP STEREO
DRIVE
AM MUTE
DET
IF FF FF FF

AM/FM AM VCO
PILOT
IF S METER
FM S-CURVE DET
S METER BUFF PHASE
TUNING DET
FM FM DRIVE
IF DET

GND VCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FM-IN

AM-MIX
FM-IF

AM-IF

GND

TUNED

STEREO

VCC

FM DET

AM. SD

FM. SD

AM. SD ADJ

IF-BUFF
MUTE

AM/FM

VCO-STOP

(Page 51) (Page 64)

• Indication of transistor

BC E
These are omitted

– 83 – – 84 –

Downloaded from www.Manualslib.com manuals search engine

 IC1701 IR3R42

SUBOUT
SUBIN

LPF1A

LPF1B

LPF2A

LPF2B
DETIN
MON

GND
VCO
20 19 18 17 16 15 14 13 12 11
AMP
1/2 OSC PHASE
1/2
COMPARATOR
AMP
PHASE
PHASE
COMPARATOR 2

TRIGGER

WAVEFORM
SEP.
AMP
REGULATOR SAMPLE
GATE & HOLD MUTE
BUFFER

1 2 3 4 5 6 7 8 9 10
VCC

IN

POUT

RHC

LHC

ROUT
LOUT

ST

VCO STOP

LAMP
IC1702 MC14053BCP IC1751 NJM4558D

B1 1 16 VDD
A OUT 1 8 VCC

B0 2 15 B.COM A 7 B OUT
OPEN – +
C1 3 14 A.COM A IN– 2 B
+ –
A IN+ 3 6 B IN–
C.COM 4 13 A1
OPEN VEE 4 5 B IN+
CO 5 12 A0

INH 6 11 A

VEE 7 10 B
OPEN

VSS 8 9 C

IC1752 BU1922
TSTLD
OSCO
RDCL

VDDD

TEST
OSCI

VSSD
TS7

16 15 14 13 12 11 10 9

TEST LOGIC AND OUTPUT

SELECTOR SWITCH

OSCILLATOR 57kHz ANTI-

QUALITY BIT RECONSTRUCTION
AND BANDPASS ALIASING
GENERATOR FILTER
DIVIDER (8th ORDER) FILTER

BIPHASE CONTAS LOOP

DEFFERENTIAL CLOCKED
SYMBOL VARIABLE AND
DECODER COMPARATOR
DECODER FIXED DIVIDER

CLOCK REGENERATION
AND SYNC

VP1

REFERENCE
VOLTAGE

1 2 3 4 5 6 7 8
QUAL

RDDA

Vref

MUX

VDDA

VSSA

CIN

SCOUT

– 85 –
Downloaded from www.Manualslib.com manuals search engine
 • CD section

IC101 CXA1992AR

RF_M

RF_O
RFTC

RF_I
PD2

PD1

CC1

CC2

FOK
PD

LD

CP

CB
39 38 37 36 35 34 33 32 31 30 29 28 27
VEE

–
+
–
+

–
+

–
+
RF SUMMING
PD2 IV PD1 IV

–
+
AMP
AMP AMP

–
+
+
–
FE_BIAS 40 26 SENS2

–
+
VCC +

+
–
APC –

VEE IIL
F 41 – ↓ 25 SENS1
+ LASER POWER CONTROL
TTL
F IV AMP VCC

–
+

+
–
+
VCC FE AMP VCC
E 42 – 24 C. OUT
–
+

–
+
+
E IV AMP
VEE

–
+

+
–
DFCT
–
+

EI 43 23 XRST

–
+
IFB4
IFB5
IFB2
IFB3

IFB6
IFB1
BAL1
BAL2
BAL3
BAL4

+
VEE

–
+
–
LEVEL S
VEE
TGFL

VEE
VEE 44 VEE 22 DATA
TOG4
TOG3
TOG2
TOG1

FO. BIAS

–
–

+
+
WINDOW VCC
–
+

MIRR IIL
+ COMP. ↓
–
+

– TTL TTL
TEO 45 + TRK. GAIN FOK ↓ 21 XLT
– WINDOW COMP. IIL
+ +
– –

DFCT1
LDON

E-F BALANCE

MIRR
LPCL

TGFL
LPC

CC1
LPFI 46 + WINDOW COMP. 20 CLK
+
– FOH
–
FOL
TGH
TGL IIL DATA REGISTER
TEI 47 19 LOCK
BALH INPUT SHIFT REGISTER
– ADDRESS DECODER
+ BALL
SENS SELECTOR
ATSC
OUTPUT DECODER
TZC
ATSC 48 – FZC VCC 18 VCC
+
ATSC
WINDOW
COMP.
DFCTO IFB1-6 FS1-4 TG1-2 TM1-7 PS1-4
TZC 49 – BAL1-4 ISET 17 ISET
+ TOG1-4
DFCT
TZC COMP.
TM1
VCC VCC
TDFCT 50 TRACKING 16 SL_O
VCC TG1 PHASE COMPENSATION
TM4 TM6

+
VC 51 – 15 SL_M
VCC
TM7
VCC VEE
FOCUS FS1 TM5
PHASE COMPENSATION TM3 –
FZC 52 + + 14 SL_P
–
VEE VEE
+ FS2 TM2
DFCT – Charge
up FSET
FZC COMP.
TG2
–

FS4
+

VEE
1 2 3 4 5 6 7 8 9 10 11 12 13
FEO

FEI

FDFCT

FGD

FLB

FE_O

FE_M

SRCH

TGU

TG2

FSET

TA_M

TA_O

– 86 –
Downloaded from www.Manualslib.com manuals search engine
 IC102 BA5941FP

OP IN (–)

OP IN (+)
OP OUT

OUT3A

OUT3B

OUT4A

OUT4B
IN4B

IN4A

IN3B

IN3A

GND

VCC
NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15
NC
– +
Vcc + – + – + – + –

–
+ LEVEL SHIFT
–
+ LEVEL SHIFT

+
LEVEL SHIFT
–
+
LEVEL SHIFT
–

– + + – – + + –
Vcc MUTE Vcc

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VCC

BIAS IN

IN1B

IN1A

IN2B

IN2A

GND

GND

MUTE

VCC

OUT2A

OUT2B

OUT1A

OUT1B
IC103 CXD2519Q

PCMDI
EMPHI

PCMD
LRCKI
SYSM

EMPH
WFCK

MNT0
MNT1
MNT3
SCOR

DOUT
SBSO

GTOP
XPCK
XROF
C2PO

XUGF
EXCK

RFCK
XTSL
FSTT

BCKI
C4M
VDD

VDD
VSS

VSS

BCK
GFS

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

NC 81 50 LRCK
AVSS 82 49 WDCK
AVDD 83 48 ASYE
AOUT1 84 47 ASYO
– ASYMMETRY
AIN1 85 46 ASYI
– CORRECTOR
PWM

+
3RD-ORDER NOISE SHAPER

LOUT1 86 + 45 BIAS
AVSS 87 44 RF
ERROR
XVDD 88 CORRECTOR 43 AVDD
D/A
XTAI 89 EFM INTERFACE 42 CLTV
DEMODURATOR DIGITAL
XTAO 90 – 41 AVSS
PLL
PWM

XVSS 91 – + 40 FILI
+
AVSS 92 16K RAM DIGITAL OUT 39 FILO
LOUT2 93 38 PCO
AIN2 94 OSC 37 VCTL
AOUT2 95 36 V16M
AVDD 96 35 VCKI
SERIAL-IN OVER SAMPLING SUB CODE
CLOCK
AVSS 97 INTERFACE DIGITAL FILTER PROCESSOR 34 VPCO1
GENERATOR
NC 98 33 VPCO2
NC 99 TIMING SERVO 32 TES1
LOGIC CPU
XRST 100 AUTO DIGITAL CLV 31 TES0
INTERFACE
SEQUENCER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
VDD
VSS
LMUT
RMUT
TES2
CKOUT
SQCK
SQSO
SENS
DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA
SPOB
SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP
MDS
LOCK
PWMI

– 87 –
Downloaded from www.Manualslib.com manuals search engine
 • Main section

IC201 LV1041M

L+R RECT
L-R RECT
DC CUT1

DC CUT2

DC CUT4

DC CUT3
VCS TH

VLR TH

R RECT
R DET3

L RECT

L BPF3
VCS 1

VCS 2

VLR 2

VLR 1
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65

R BPF2 1 64 L BPF2
RECT RECT

LOGIC LOGIC
R BPF1 2 BPF RECT RECT BPF 63 L BPF1
FF FF
LOGIC LOGIC

VCA VCA VCA VCA

P
VOL R 62 RT IN

B
S DC OUT 3
C DC OUT 4 VCA VCA VCA VCA
P
R DC OUT 5 VOL L 61 LT IN
L DC OUT 6
B
CH
CONTROL
60 DC CUT
V REF 7 V REF S BPF
VCC 8 MODE CONTROL
59 C MODE
C OUT 9 C STRIM C MODE 58 GND
NOISE 57 NS BPF1
FILTER 56 NS BPF2
S OUT 10 S
OSC 55 OSC
P P
R NOISE
R OUT 11 R B IEV
GEN
B
P P
L
L OUT 12
12 L B
B
54 CLK
STRIM B NR
GND 13
P P B
DC DATA
VOL/ 53 DATA
CUT OUT DECODER
B MUTE
L IN 14 P D C FILTER
L
B 52 ENABLE
P P
P
R IN 15 P S IN
R B FILTER
B B 51 DATA
B
50 CLK
S IN 16 SRAM 49 ENABLE2
S 48 VSS
P
PCM
DELAY OUT 17 S 47 OSC
P P CONTROL
B B
B
C VOL IN 18 46 OSC
S R L
PCM
VDD 45 VDD
DET 19
IREF 20
20

R OUT 21 R 44 A/D

L
R NF 22 NF 43 NS
SW
L NF 23
C S MASTER VOL
MASTER 42 D/A
L OUT 24 VOL
41 DC CUT

25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
VCC

C VOL OUT

C OP IN
GND

C OP NF

C OP OUT

VOL REF

S OP OUT

S OP NF

S OP IN

S VOL OUT

OP VREF

S VOL IN

S OUT

DC CUT

– 88 –
Downloaded from www.Manualslib.com manuals search engine
 • Deck section • Display section

IC602 uPC1330HA IC603 BA3833FP

INVERTER RESET 1 RESET 18 RESET

C

PREF 2 REFFERENCE 17 f01

CURRENT
COMPARATER
BPF DET
2 3 4 5 6 7 8 9 LINE 3 16 f02
1
NF
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2

BPF DET
LINE
4 15 f03
IN

BPF DET
GND 5 14 f04
• CD motor section
IC701 M54641L BIAS 6
BPF DET
13 f
C Bias

VCC VCC
DET
1 8 NC 7 12 VCC

REG 5 REFERENCE

NC 8 11 NC
POWER 2 OUT2
IN1 3 INPUT AMP.
AMP.

CONTROL NC 9 10 NC
POWER 7 OUT1
INPUT AMP.
IN2 6 AMP.

4
GND IC851 MSM6653A-517GS-K

VDD 1
IC801 BA6286N
XT 2
OSC
XT 3 24 GND
SOUND
NC 4 23 A-OUT
PO WER MIX
GND 1 CMD 5 22 NAR
SAVE
RIN 2 NC 6 21 NC
VREF 3 NC 7 20 BUSY
OUT2 4 NC
ST 8 19
RNF 5
TSD CONTROL I0 9 18 VPP
GND 6 LOGIC I1 10 17 RST
OUT1 7
I2 11 µ CON 16 CH
VM 8 ROM INTER FACE
I3 12 15 SD
VCC 9
FIN 14 SI
10
13 I4

– 89 –
Downloaded from www.Manualslib.com manuals search engine
 7-33. IC PIN FUNCTIONS
• IC101 FOCUS/TRACKING/SLED SERVO RF AMP (CXA1992AR)

Pin No. Pin Name I/O Function

Focus error amplifier output
1 FEO O
Connected internally to the window comparator input for bias adjustment
2 FEI I Focus error input
3 FDFCT I Capacitor connection pin for defect time constant
4 FGD I Ground this pin through a capacitor for cutting the focus servo high-frequency gain
5 FLB I External time constant setting pin for boosting the focus servo low-frequency
6 FE O O Focus drive output
7 FE M I Focus amplifier inverted input
8 SRCH I External time constant setting pin for generating focus search waveform
9 TGU I External time constant setting pin for switching tracking high-frequency gain
10 TG2 I External time constant setting pin for switching tracking high-frequency gain
11 FSET I Peak frequency setting pin for focus and tracking phase compensation amplifier
12 TA M I Tracking amplifier inverted input
13 TA O O Tracking drive output
14 SL P I Sled amplifier non-inverted input
15 SL M I Sled amplifier inverted input
16 SL O O Sled drive output
Connect an external capacitance to set the current which determines the Focus search,
17 ISET I
Track jump, and Sled kick heights
18 VCC I Positive power supply
19 LOCK I The sled overrun prevention circuit operates when this pin is Low (No pull-up resistance)
20 CLK I Serial data transfer clock input from CPU (No pull-up resistance)
21 XLT I Lach input from CPU (No pull-up resistance)
22 DATA I Serial data input from CPU (No pull-up resistance)
23 XRST I Reset input; resets at Low (No pull-up resistance)
24 C.OUT O Track number count signal output
Outputs FZC, DFCT1, TZC, BALH, TGH, FOH, ATSC, and others according to the com-
25 SENS1 O
mand from CPU
Outputs DFCT2, MIRR, BALL, TGL, FOL,and others according to the command from
26 SENS2 O
CPU
27 FOK O Focus OK comparator output
28 CC2 I Input for the defect bottom hold output with capacitance coupled
Defect bottom hold output
29 CC1 O
Connected internally to the interruption comparator input
30 CB I Connection pin for defect bottom hold capacitor
Connection pin for MIRR hold capacitor
31 CP I
MIRR comparator non-inverted input
32 RF I I Input for the RF summing amplifier output with capacitance coupled
RF summing amplifier output
33 RF O O
Eye-pattern check point

• Abbreviation
FZC : Focus zero-cross ATSC : Anti Shock
DFCT : Defect MIRR : Mirror
TZC : Tracking zero-cross BALL : E-F Balance (Low)
BALH : E-F Balance (High) TGL : Tracking Gain (Low)
TGH : Tracking Gain (High) FOL : Focus Bias (Low)
FOH : Focus Bias (High)

– 90 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
RF summing amplifier inverted input
34 RF M I The RF amplifier gain is determined by the resistance connected between this pin and
RFO pin
35 RFTC I External time constant setting pin during RF level control
36 LD O APC amplifier output
37 PD I APC amplifier input
38 PD1 I RF I-V amplifier inverted input
39 PD2 I Connect these pins to the photo diode A+C and B+D pins
Bias adjustment of focus error amplifier
40 FE BIAS I
Leave this pin open for automatic adjustment
41 F I F I-V and E I-V amplifier inverted input
42 E I Connect these pins to photo diodes F and E
I-V amplifier E gain adjustment
43 EI –
(When not using automatic balance adjustment)
44 VEE – Negative power supply
Tracking error amplifier output
45 TEO O
E-F signal is output
Comparator input for balance adjustment
46 LPFI I
(Input from TEO through LPF)
47 TEI I Tracking error input
48 ATSC I Window comparator input for ATSC detection
49 TZC I Trackig zero-cross comparator input
50 TDFCT I Capacitor connection pin for defect time constant
51 VC O (VCC + VEE)/2 direct voltage output
52 FZC I Focus zero-cross comparator input

• Abbreviation
APC : Auto Power Control

– 91 –
Downloaded from www.Manualslib.com manuals search engine
 • IC103 DIGITAL SIGNAL PROCESSOR (CXD2519Q)

Pin No. Pin Name I/O Function

1 VDD – +5V power supply
2 VSS – Ground
3 LMUT O Lch “L” detection flog (Not used)
4 RMUT O Rch “L” detection flog (Not used)
5 ACDT O Test output (Not used)
6 CKOUT O Master clock divider output (Not used)
7 SQCK I Clock input for SQSO read out
8 SQSO O Serial output for Sub-Q 80bit
9 SENS O SENS signal output to CPU
10 DATA I Serial data input, supplied from CPU
11 XLAT I Latch input, supplied from CPU
12 CLOK I Serial data transfer clock input, supplied from CPU
13 SEIN I SENS input from IC101
14 CNIN I Numbers of track jump counted signal input
15 DATO O Serial data output to IC101
16 XLTO O Serial data latch output to IC101
17 CLKO O Serial data transfer clock output to IC101
18 SPOA I Micro computer demodulation interface (Input A)
19 SPOB I Micro computer demodulation interface (Input B)
20 SPOC I Micro computer demodulation interface (Input C)
21 SPOD I Micro computer demodulation interface (Input D)
22 XLON O Micro computer demodulation interface (Output)
23 FOK I Focus OK input
24 VDD – +5V power supply
25 VSS – Ground
26 MON O Output to control ON/OFF of spindle motor (Not used)
27 MDP O Output to control spindle motor servo
28 MDS O Output to control spindle motor servo (Not used)
29 LOCK O GFS is sampled by 460Hz
30 PWMI I Input to control the outside spindle motor
31 TES0 I Test pin (Connected to ground)
32 TES1 I Test pin (Connected to ground)
33 VPCO2 O Charge-pump output (Not used)
34 VPCO1 O Charge-pump output (Not used)
35 VCKI I VCO2 oscillator input (Not used)
36 V16M O VCO2 oscillator output (Not used)
37 VCTL I VCO2 control voltage input
38 PCO O Charge-pump output to master PLL
39 FILO O Filter output to master PLL
40 FILI I Filter input for master PLL

• Abbreviation
GFS : Guarded Frame Sync
PLL : Phase Locked Loop

– 92 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
41 AVSS – Analog ground
42 CLTV I Control voltage input for VCO
43 AVDD – Analog power supply
44 RF I EFM signal input
45 BIAS I Asymmetry circuit constant current input
46 ASYI I Asymmetry comparate voltage input
47 ASYO O EFM full swing output (“L” =VSS, “H” =VDD )
48 ASYE I Asymmetry circuit ON/OFF (“L”=OFF, “H”=ON)
49 WDCK O D/A interface Word clock f=2fs (Not used)
50 LRCK O D/A interface LR clock output f=Fs
51 LRCKI I D/A interface LR clock input f=Fs
52 PCMD O D/A interface Serial data output
53 PCMDI I D/A interface Serial data input
54 BCK O D/A interface Bit clock output
55 BCKI I D/A interface Bit clock input
56 VSS – Ground
57 VDD – +5V power supply
58 GTOP O Not used
59 XUGF O Not used
60 XPLCK O EFM decoder PLL clock output
61 GFS O “H” Playback EFM sync and interpolation protection timming much
62 RFCK O Read frame clock signal output
63 C2PO O Not used
64 XRAOF O Internal RAM overflow detection signal output (Not used)
65 MNT3 O Not used
66 MNT1 O Not used
67 MNT0 O Not used
68 XTSL I Not used
69 FSTT O 2/3 divider output (Not used)
70 C4M O 4.2336MHz output(Not used)
71 DOUT O Digital audio signal output
72 EMPH O Playback disc output in emphasis mode
73 EMPHI I “H” =Input when de-emphasis ON
74 WFCK O Write frame clock signal output
75 SCOR O Sub-code sync output
76 SBSO O Sub-P through Sub-W serial output
77 EXCK I Clock input for SBSO read-out
78 VSS – Ground
79 VDD – +5V power supply
80 SYSM I System mute input

• Abbreviation
EFM : Eight to Fourteen Modulation

– 93 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
81 — – Not used
82 AVSS – Analog ground
83 AVDD – Analog power supply
84 AOUT1 O Lch analog output
85 AIN1 I Lch opamp input
86 LOUT1 O Lch line output
87 AVSS – Analog ground
88 XVDD – Master clock power supply
89 XTAI I X’tal oscillator circuit input
90 XTAO O X’tal oscillator circuit output
91 XVSS – Master clock ground
92 AVSS – Analog ground
93 LOUT2 O Rch line output
94 AIN2 I Rch opamp input
95 AOUT2 O Rch analog output
96 AVDD – Analog power supply
97 AVSS – Analog ground
98 — – Not used
99 — – Not used
100 XRST I System reset input

– 94 –
Downloaded from www.Manualslib.com manuals search engine
 • IC501 MASTER CONTROL (uPD780018AYGF-012-3BA)

Pin No. Pin Name I/O Function

1 LINE-MUTE O Line mute signal output
2 DBFB-H/L O DBFB H/L select signal output
3 M62442-LAT O Latch signal output for IC111 (M62442FP)
4 KCON-LAT O Not used
5 POWER O Power ON/OFF signal output
6 F-RELAY O Front speaker relay control output
7 R-RELAY O Rear speaker relay control output (Not used)
8 PL-RELAY O Surround speaker relay control output
9 VSS – Ground
10 X2 O
X’tal (5MHz)
11 X1 I
12 VDD – Power supply (+5V)
13 XT2 O
X’tal (32.768 KHz)
14 XT1 I
15 RESET I Reset signal input
16 (AC-CUT) I Back up signal input
17 CAPM-CNT1P I Capstan motor control 1 (+) signal output
18 SCOR O Subcode data request signal output
19 SOFT-TEST O Software test port
20 — – Not used
21 RDS-INT I RDS data interrupt input
22 RDS-DATA I RDS data interrupt input
23 AVDD – Power supply (+5V)
24 AVREF I Analog reference voltage input.
25 ADJ I CD adjust point port Normal “H”
26 A-SHUT I A Deck reel pulse detector
27 B-SHUT I B Deck reel pulse detector
28 B-HALF I Half detector signal input
29 CLK-CHECK I Connected to ground
30 SPEC-IN I Version select signal input
31 AMS-IN I Connected to ground
32 DEMO-CHANGE I DEMO H/L select signal input (Connected to ground)
33 AVSS – Ground
34 SQ-DATA-IN I Subcode Q data clock input
35 — – Not used
36 SQ-CLK I Sub code Q data clock input
37 SUR-ON/OFF O Not used
38 FB CONT-A I Not used
39 FB CONT-B I Connected to ground
40 VSS – Ground
41 PL-VOL O Latch signal output to erectrial volume
42 PL-LAT O Latch signal input to pro-logic
43 COM-DIN I Connected to ground
44 COM-DOUT O Common serial data output (Not used)

• Abbreviation
APC : Auto Power Control

– 95 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
45 COM-CLK O Common serial clock output
46 CD-POWER O CD power on signal output
47 CD-DATA O CD data output
48 CD-CLK O CD clock output
49 PL-CLK O Clock signal output to pro-logic
50 PL-DATA I Data signal output to pro-logic
51 M62442-CLK O Clock signal output for IC111 (M62442FP)
52 M62442-DATA O Data signal output for IC111 (M62442FP)
53 LEVEL-CONT-A O Not used
54 LEVEL-CONT-B O Not used
55 IIC-DATA O Data output for IC601
56 IIC-CLK O Clock output for IC601
57 XRST O CD reset signal output
58 XLT O CD latch signal output
59 FCS-SW O Not used
60 TBL-L O
Table motor control output
61 TBL-R O
62 — O Not used
63 LOAD-OUT O
Loading motor control signal output
64 LOAD-IN O
65 ST-CLK O Tuner clock output
66 ST-DIN I Tuner data input
67 ST-DOUT O Tuner data output
68 ST-CE O Tuner chip enable output
69 TUNED I Tuned detection for tuner
70 STEREO I Stereo detection for tuner
71 VSS – Ground
72 ST-MUTE O Tuner mute signal output
73 SENS2 I
BD Condition signal input
74 SENS I
75 DISC-SENS I Slit sensor of disc table input
76 T-SENS I CD table detection signal input
77 CAPM-CNT2P O Capstan motor control 2 (+) signal output
78 ENC 3 I
79 ENC 2 I Disc tray adrress detect encoder input
80 ENC 1 I
81 OUT-OPEN O Loading out detection signal output
82 CAP-M-H/L O Capstan motor H/N speed select signal output
83 B-TRG O Trigger motor control output
84 A-TRG O Trigger motor control output
85 CAPM-CONT1M O Capstan motor control 1 (–) signal output
86 CAPM-CONT2M O Capstan motor control 2 (–) signal output
87 TC-MUTE O TC mute ON/OFF selection output

– 96 –
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Function
88 R/P-PASS O REC/PB/PASS selection output
89 NR-ON/OFF O NR ON/OFF signal output
90 REC-MUTE O REC mute ON/OFF selection output
91 CLK-OUT O Clock out signal check
92 BIAS O Bias ON/OFF signal output
93 EQ-H/N O Equalizer H/N select output
94 PB-A/B O PB Deck A/Deck B select output
95 A-PLAY-SW I Deck A play detect
96 B-PLAY-SW I Deck B play detect
97 TC-RELAY O REC/PB head selection output for IC602
98 A-HALF I Deck A cassette detect
99 ALC-ON/OFF O ALC ON/OFF output signal
100 STK-MUTE O Power amp ON/OFF signal output

– 97 –
Downloaded from www.Manualslib.com manuals search engine
 • IC601 DISPLAY CONTROL ( TMP87CM74AF)

Pin No. Pin Name I/O Function

1 to 6 LED3 to LED8 O LED driver output
7 VSS – Ground
8 X OUT O
X’tall (8MHz)
9 X IN I
10 RESET I Reset signal input from main controller
11 LED9 O
LED driver output
12 LED10 O
13 TEST I Connected ground
14 to 18 LED11 to LED15 O LED driver output
19 VOL A I
Rotary encoder (S602) pulse input
20 VOL B I
21 JOG A I
Rotaly encoder (S601) pulse input
22 JOG B I
23 SCL O Serial clock input from master controller
24 SDA O Serial data input from master controller
25 L. SEL O LED select signal output
26 to 29 KEY 0 to KEY 3 I Key input
30 MODEL I Version select signal input
31 (LED 16 OPEN) – LED driver output (Not used)
32 L+R I Spectrum analyzer (high frequency) input
33 SIRCS I Remote commander signal input
34 to 37 SPEANA 1 to SPEANA 4 I Spectrum analyzer input
38 VASS – Ground
39 VAREF I Analog reference voltage input
40 VDD – Power supply (+5V)
41 to 53 GR 1 to GR13 O FL gride signal output
54 to 77 SEG 1 to SEG 24 O FL segment signal output
78 VKK – Power supply (–25V) for FL segment signal output
79 LED 1 O
LED driver output
80 LED 2 O

• Abbreviation
FL : Fluorescent indicator tube

– 98 –
Downloaded from www.Manualslib.com manuals search engine
 • IC801 PANEL CONTROL ( TMP87CH48DF)

Pin No. Pin Name I/O Function

1 VSS – Ground
2 X OUT O
X’tall (8MHz)
3 X IN I
4 RESET I Reset signal input
5 MUTE I Mute ON/OFF selection input
6 MODE_0 I
7 TEST –
Connected to ground
8 MODE_1 I
9 YB_CLK O
10 NAR/YB_RDY I Connected to VDD
11 MSM6654/BSY I Busy signal input for IC851 (MSM6653A)
12 MSM6654/RST O Reset signal output for IC851 (MSM6653A)
13 MSM6654/CH O Channel signal output for IC851 (MSM6653A)
14 MSM6654/DATA O Data signal output for IC851 (MSM6653A)
15 MSM6654/CLK O Clock signal output for IC851 (MSM6653A)
16 MSM6654/LAT O Latch signal output for IC851 (MSM6653A)
17 YB_D0 I Connected to ground
18 IC2 CLK I Serial clock input from master controller
19 IC2 DATA I Serial data input from master controller
20 YB_D3 I
21 UART RX I Connected to ground
22 UART TX O
23 to 26 NC O Connected to ground
27 JOG_A I
Rotary encoder (S601) pulse input
28 JOG_B I
29 SIRCS I Remote commander signal input
30 VASS – Ground
31 VAREF I Analog reference voltage input
32 DVDD – Power supply (+5V)
33 BPF/LOW I Spectrum analyzer input
34 BPF/LOW-MID I Connected to ground
35 BPF/HIGH-MID I Connected to ground
36 BPF/HIGH I Spectrum analyzer input
37 L+R I Spectrum analyzer (high frequency) input
38 KEY/0 I
Key input
39 KEY/1 I
40 KEY/2 I Connected to VDD
41 to 56 NC O Not used
57 to 60 GND – Ground
61 BPM_LED_B O
62 BPM_LED_A O
LED Drive output
63 BOMBER_LED O
64 ON/OFF_LED O

– 99 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 8
EXPLODED VIEWS
NOTE:
• Items marked “*” are not stocked since they are • Abbreviation
seldom required for routine service. Some delay CND : Canadian model The components identified by
should be anticipated when ordering these items. G : German model. mark ! or dotted line with mark
• The mechanical parts with no reference number in EE : East European model. ! are critical for safety.
the exploded views are not supplied. AUS : Australian model. Replace only with part number
• Hardware (# mark) list and accessories and packing EA : Saudi Arabia model. specified.
materials are given in the last of this parts list. SP : Singapore model. Les composants identifiés par une
HK : Hong Kong model. marque ! sont critiques pour la
MY : Malaysia model. sécurité.
TH : Thai model. Ne les remplacer que par une
E2 : Without SW tuner E model. piéce portant le numéro spécifié.
E3 : With SW tuner E model.
8-1. CASE SECTION
CDM38L-5BD29AL
1 #2 CDM38LH-5BD29AL
#2
2

7
#2
3 5
#2

#1 #2
2 #2

Front panel

#2
#3 M901
#2
#2
3

4
8
6 (EXCEPT AEP,UK,
#3 G,EE,CIS)

6 (AEP,UK,G,EE,CIS)

#2
9

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-996-816-01 CASE * 6 A-4303-588-A TCB BOARD, COMPLETE (EE,CIS)
2 3-363-099-71 SCREW (CASE 3 TP2)
3 3-363-099-11 SCREW (CASE 3 TP2) * 6 A-4303-590-A TCB BOARD, COMPLETE (AEP,UK,G)
4 4-996-784-41 PANEL, LOADING (GRX10AV:EXCEPT TH) 6 1-693-419-11 TUNER (FM/AM) (CND)
4 4-996-784-51 PANEL, LOADING (GRX10AV:TH/RX110AV) 6 1-693-420-11 TUNER (FM/AM) (E2,TH,AUS)
6 1-693-421-11 TUNER (FM/AM) (E3,EA,SP,MY,HK)
* 5 4-996-819-01 PANEL, BACK (RX110AV:AEP,G,UK) 7 4-956-370-12 BAND, PLUG FIXED
* 5 4-996-819-11 PANEL, BACK (RX110AV:EE,CIS) (GRX10AV:HK,AUS/RX110AV:UK)
* 5 4-996-819-21 PANEL, BACK (RX110AV:CND)
* 5 4-996-819-31 PANEL, BACK (GRX10AV:TH) 8 1-769-977-11 WIRE (FLAT TYPE) (13 CORE)(150mm)
* 5 4-996-820-01 PANEL, BACK (GRX10AV:E2,E3) (GRX10AV:E2,TH,AUS/RX110AV:CND)
8 1-773-009-11 WIRE (FLAT TYPE) (15 CORE)(150mm)
* 5 4-996-820-11 PANEL, BACK (GRX10AV:SP,MY) (GRX10AV:E3,EA,SP,MY,HK/RX110AV:AEP,G,UK,EE,CIS)
* 5 4-996-820-21 PANEL, BACK (GRX10AV:HK) 9 4-924-098-91 HOLDER, PC BOARD (RX110AV:AEP,G,UK,EE,CIS)
* 5 4-996-820-31 PANEL, BACK (GRX10AV:AUS) M901 1-698-792-11 FAN, DC (RX110AV)
* 5 4-996-820-41 PANEL, BACK (GRX10AV:EA) M901 1-763-048-21 FAN, D.C. (GRX10AV)

– 100 –
Downloaded from www.Manualslib.com manuals search engine
 8-2. CHASSIS SECTION
#5

not supplied
not supplied #5 61 53

54

#5 62
#2
60
58 (UK,HK)
51
58 (SP,MY,EA)

58 (E3)

#4
#5 55
52

59 (AEP,UK,G, 59 (E2,E3,TH)
T501 #6 56 EE,CIS,SP,
MY,HK,EA)

#6 #6

59 (AUS)

59 (CND)
#5

not supplied #5
The components identified by Les composants identifiés par une
mark ! or dotted line with mark marque ! sont critiques pour la
57 ! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 51 A-4407-272-A POWER BOARD, COMPLETE ! 58 1-569-008-11 ADAPTOR, CONVERSION 2P (EA,SP,MY)
(RX110AV:AEP,G,UK,EE,CIS) ! 58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK)
* 51 A-4407-298-A POWER BOARD, COMPLETE (GRX10AV)
* 51 A-4407-320-A POWER BOARD, COMPLETE (RX110AV:CND) ! 59 1-558-943-41 CORD, POWER (E2,E3)
* 52 1-668-274-11 TRANSFORMER BOARD ! 59 1-575-042-21 CORD, POWER (CND)
* 53 A-4407-262-A MAIN BOARD, COMPLETE (RX110AV:AEP,G,UK) ! 59 1-575-651-21 CORD, POWER (AEP,G,UK,EE,CIS,EA,SP,MY,HK)
! 59 1-696-845-31 CORD, POWER (AUS)
* 53 A-4407-280-A MAIN BOARD, COMPLETE (RX110AV:EE,CIS) ! 59 1-751-326-21 CORD, POWER (TH)
* 53 A-4407-284-A MAIN BOARD, COMPLETE
(GRX10AV:E3,EA,SP,MY,HK) 60 1-773-011-11 WIRE (FLAT TYPE) (15 CORE)
* 53 A-4407-286-A MAIN BOARD, COMPLETE (GRX10AV:E2) 61 1-773-112-11 WIRE (FLAT TYPE) (19 CORE)
* 53 A-4407-314-A MAIN BOARD, COMPLETE (RX110AV:CND) * 62 A-4407-269-A SURROUND BOARD, COMPLETE
* 53 A-4407-755-A MAIN BOARD, COMPLETE (GRX10AV:TH) (RX110AV:AEP,G,UK,EE,CIS)
* 62 A-4407-319-A SURROUND BOARD, COMPLETE (RX110AV:CND)
* 53 A-4407-768-A MAIN BOARD, COMPLETE (GRX10AV:AUS) * 62 A-4414-862-A SURROUND BOARD, COMPLETE (GRX10AV)
54 1-773-041-11 WIRE (FLAT TYPE) (17 CORE)
55 3-703-244-00 BUSHING (FBS001), CORD ! T501 1-431-709-11 TRANSFORMER, POWER
(GRX10AV:EA,SP,MY,HK,AUS/RX110AV) (GRX10AV:E2,EA,SP,MY,HK,AUS)
55 3-703-571-11 BUSHING (S) (4516), CORD (GRX10AV:TH) ! T501 1-431-710-11 TRANSFORMER, POWER
55 4-966-266-01 BUSHING (S) (FBS002), CORD (GRX10AV:E2,E3) (RX110AV:AEP,G,UK,EE,CIS)
! T501 1-431-711-21 TRANSFORMER, POWER (GRX10AV:TH)
* 56 4-988-533-01 HOLDER, PWB ! T501 1-431-712-11 TRANSFORMER, POWER (RX110AV:CND)
57 4-965-822-01 FOOT ! T501 1-431-769-11 TRANSFORMER, POWER (GRX10AV:E3)
! 58 1-569-007-11 ADAPTOR, CONVERSION 2P (E3)

– 101 –
Downloaded from www.Manualslib.com manuals search engine
 8-3. FRONT PANEL SECTION

not supplied 123

123
not supplied 118
126

123
125 (EA3)
119
123
120
125
123 123
supplied with 117
J750,751
110
ND601 120
123
121
123
127 TCM230AWR1
129 111 116 123 TCM230PWR1
116 115
122
107 #7 123
107
105 123 131
103
108 122
123
#7
123
123
not supplied 114 124 123
not supplied #2
113
101
102 104
109
128 106
not supplied
supplied
112 with J755
123
130

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 4-996-808-01 WINDOW (TCL) * 117 1-668-268-11 CD SW BOARD
102 4-996-809-01 WINDOW (TCR) * 118 A-4407-266-A PANEL BOARD, COMPLETE (RX110AV:AEP,G,UK)
103 4-996-799-01 LID (A), CASSETTE * 118 A-4407-312-A PANEL BOARD, COMPLETE
104 4-996-800-01 LID (B), CASSETTE (GRX10AV/RX110AV:CND,EE,CIS)
105 4-900-600-01 SPRING (A DECK)
* 119 4-996-796-01 HOLDER, FL TUBE
106 4-900-601-01 SPRING (B DECK) * 120 4-932-810-31 CUSHION (FL)
107 4-959-229-11 DETENT, CASSETTE 121 1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
108 4-996-810-01 KNOB (JOG) 122 3-973-975-11 DAMPER, OIL
109 4-996-811-01 KNOB (VOL) 123 4-951-620-01 SCREW (2.6X8), +BVTP
110 X-4949-327-1 PANEL ASSY, FRONT
(GRX10AV/RX110AV:CND,EE,CIS) * 124 1-668-271-11 HP BOARD
125 4-986-893-51 KNOB (MICROPHONE)
110 X-4949-328-1 PANEL ASSY, FRONT (RX110AV:AEP,G,UK,AEP) * 126 1-668-270-11 MIC BOARD
111 4-962-708-21 EMBLEM (4-A), SONY 127 X-4949-962-1 LID (L) ASSY, CASSETTE
112 4-988-663-01 FOOT (FELT) 128 X-4949-963-1 LID (R) ASSY, CASSETTE
113 A-4407-476-A CONT COM BOARD, COMPLETE
* 114 1-668-269-11 DECO BOARD 129 4-995-081-01 LATCH, DC
130 1-773-109-11 WIRE (FLAT TYPE) (19 CORE)(110mm)
115 4-996-812-01 HOLDER (LED) 131 3-701-822-00 HOLDER, WIRE
116 4-996-716-01 HOLDER (CDM) ND601 1-517-731-21 INDICATOR, TUBE FLUORESCENT

– 102 –
Downloaded from www.Manualslib.com manuals search engine
 8-4. CD MECHANISM DECK SECTION-1 CDM38L-5BD29AL
CDM38LH-5BD29AL ( )
201

202

201 206
#2
203 M701
204
211 #8

205

207
208

210
212

209

#2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 4-981-789-01 BRACKET (2), YOKE 208 4-977-941-01 BEARING (WORM)
202 4-977-945-01 TRAY (TURN) * 209 1-658-576-11 SENSOR BOARD
203 X-4946-665-1 SHAFT ASSY, WORM 210 4-934-376-01 SHAFT (ROLLER)
204 4-977-943-01 BELT (TURN) (1.2)
205 4-977-956-01 WHEEL, WORM 211 4-981-187-01 COLLAR (WORM)
212 4-977-944-01 TRAY (SLIDE)
* 206 1-658-577-11 MOTOR (TURN) BOARD M701 A-4672-004-A MOTOR ASSY (TURN)
207 4-988-162-01 ROLLER

– 103 –
Downloaded from www.Manualslib.com manuals search engine
 8-5. CD MECHANISM DECK SECTION-2 CDM38L-5BD29AL
CDM38LH-5BD29AL ( )
HOW TO DISCRIMINATE 251
(MAGNET Ref.No.257,270)

FOR CDM38L 251 253 252

-5BD29AL

255

FOR CDM38LH 254 CDM38L CDM38LH

-5BD29AL -5BD29AL -5BD29AL
257 257

258
not
supplied not
256 not supplied
supplied

259 270
266
#2
260
267
269
268
261
261 M801

BU-5BD29AL

S811 262

263

#2
263

264

265
251
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 4-917-583-71 BRACKET, YOKE * 262 1-658-578-11 MOTOR (SLIDE) BOARD
252 4-977-954-01 PULLEY (SL) 263 4-982-447-01 SPRING (BU), COMPRESSION
253 4-977-953-01 GEAR (SL-A) 264 4-951-620-41 SCREW (2.6), +BVTP
254 4-977-955-01 GEAR (SL-B)
255 4-977-942-01 BELT (SL) (1.4) * 265 X-4946-666-1 HOLDER (BU) ASSY
266 4-989-494-01 SCREW (SLIDER), STEP
256 X-4946-667-1 CAM ASSY, BU 267 4-989-492-21 SLIDER (38)
257 1-452-879-11 MAGNET (CDM38L-5BD29AL) 268 4-989-819-02 SPRING, TENSION
257 1-452-925-21 MAGNET ASSY (CDM38LH-5BD29AL) 269 4-989-491-21 COVER, LENS
258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE)
* 259 1-658-575-11 CONNECTOR BOARD 270 4-933-142-11 PULLEY (L), PRESS (CDM38LH-5BD29AL)
M801 A-4672-004-A MOTOR ASSY (SLIDE)
* 260 X-4946-668-1 CHASSIS (CDM) ASSY S811 1-473-335-11 ENCODER, ROTARY (BU, TRAY ADDRESS DET)
261 4-985-672-01 SCREW (+PTPWH M2.6X6), FLOATING

– 104 –
Downloaded from www.Manualslib.com manuals search engine
 8-6. BASE UNIT SECTION (BU-5BD29AL)

301

302

#9

303

305
M101 304
M102

304

306

307

308

The components identified by Les composants identifiés par une

mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! 301 8-820-020-02 OPTICAL PICK-UP BLOCK KSS-213D/Q-NP 306 4-917-564-01 GEAR (P), FLATNESS
302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) * 307 A-4699-522-A BD BOARD, COMPLETE
303 4-912-567-21 GEAR (M) 308 4-951-620-01 SCREW (2.6X8), +BVTP
304 4-951-940-01 INSULATOR (BU) M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
305 4-917-565-01 SHAFT, SLED M102 X-4917-504-1 MOTOR ASSY (SLED)

– 105 –
Downloaded from www.Manualslib.com manuals search engine
 8-7. TC MECHANISM SECTION 1 TCM230AWR1
TCM230PWR1 ( )
*NOTE: Two types of parts which are not interchangeable are available
for the Head deck (A) ASSY and Head deck (B) ASSY.
When replacing the parts, refer to the following figure, and
use the appropriate part

408
Parts with “P” mark: 230PWR1
Parts without “P” mark: 230AWR1

408

407

406
404

HP101
403

407

HRPE101 403 405

406
404
405

409

402

402

401

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
401 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 407 3-016-565-01 BASE (PINCH LEVER REV)
402 3-911-116-21 RIVET, PUSH 408 3-016-567-02 SPRING (CASSETTE), LEAF
403 3-016-574-01 SPRING (HEAD), TENSION * 409 A-2007-731-A AUDIO BOARD, COMPLETE
404 X-3374-156-2 PINCH LEVER (REV) ASSY HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR1)(*NOTE)
405 X-3374-155-2 PINCH LEVER (FWD) ASSY
HP101 A-2056-683-A DECK (A) ASSY, HEAD (230PWR1)(*NOTE)
406 3-016-564-01 BASE (PINCH LEVER FWD) HRPE101 A-2056-682-A DECK (B) ASSY, HEAD (230AWR1)(*NOTE)
HRPE101 A-2056-684-A DECK (B) ASSY, HEAD (230PWR1)(*NOTE)

– 106 –
Downloaded from www.Manualslib.com manuals search engine
 8-8. TC MECHANISM SECTION 2
(TCM230AWR1
TCM230PWR1)

*NOTE: Two types of parts which are not interchangeable are available
for the mechanical block assembly. When replacing the parts,
refer to the following figure, and use the appropriate part.

Parts with “P” mark: 230PWR1

Parts without “P” mark: 230AWR1

461
451

#7

462
459

460 463
458
455 #10
#12

#10 #10
#11

460
452 454
456 #10
459
458

455
452
M1
456
457
453

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 451 X-3374-214-1 CASSIS ASSY, MAIN 459 A-2004-629-A MECHANICAL BLOCK ASSY (230AWR1)(*NOTE)
452 3-016-570-01 BELT (CAPSTAN) 459 A-2004-630-A MECHANICAL BLOCK ASSY (230PWR1)(*NOTE)
453 3-016-569-01 BELT (TENSION) 460 3-016-566-01 SLIDER, REVERSE
454 3-017-360-01 BRACKET (MOTOR)
455 X-3374-234-1 FLYWHEEL (FWD) ASSY * 461 A-2007-732-A LEAF SW BOARD, COMPLETE
462 3-016-575-01 SPRING, TORSION
456 X-3374-235-1 FLYWHEEL (REV) ASSY 463 3-019-208-01 WASHER, STOPPER
457 X-3374-238-1 PULLEY ASSY, TENSION M1 A-2004-628-A MOTOR ASSY, CAPSTAN
458 3-024-405-01 BELT (FR)

– 107 –
Downloaded from www.Manualslib.com manuals search engine
 SECTION 9
AUDIO ELECTRICAL PARTS LIST
Note:

The components identified by • Due to standardization, replacements in the parts list • COILS
mark ! or dotted line with mark may be different from the parts specified in the uH : µ H
! are critical for safety. diagrams or the components used on the set. • Abbreviation
Replace only with part number • -XX, -X mean standardized parts, so they may have CND : Canadian model
specified. some difference from the original one. G : German model.
• Items marked “*” are not stocked since they are EE : East European model.
Les composants identifiés par une seldom required for routine service. Some delay AUS : Australian model.
marque ! sont critiques pour la should be anticipated when ordering these items. EA : Saudi Arabia model.
sécurité. • RESISTORS SP : Singapore model.
Ne les remplacer que par une All resistors are in ohms HK : Hong Kong model.
piéce portant le numéro spécifié. METAL: Metal-film resistor MY : Malaysia model.
METAL OXIDE: Metal Oxide-film resistor TH : Thai model.
When indicating parts by reference F : nonflammable E2 : Without SW tuner E model.
number, please include the board
E3 : With SW tuner E model.
name. • SEMICONDUCTORS
In each case, u: µ , for example:
uA...: µ A..., uPA...: µ PA..., uPB...: µ PB...,
uPC...: µ PC..., uPD...: µ PD...
• CAPACITORS
uF : µ F

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-2007-731-A AUDIO MOUNTED BOARD, COMPLETE < CONNECTOR >
******************************
CN601 1-695-338-11 PIN, CONNECTOR (PC BOARD) 15P
< CAPACITOR >
< HEAD >
C301 1-162-289-31 CERAMIC 390PF 10% 50V
C302 1-126-968-11 ELECT 100uF 20% 6.3V HP101 A-2056-681-A DECK (A) ASSY, HEAD (PLAY BACK HEAD)
C303 1-162-282-31 CERAMIC 100PF 10% 50V 7-685-783-09 SCREW +PTT 2X6 (S)
C304 1-130-483-00 MYLAR 0.01uF 5% 50V HRPE101 A-2056-682-A DECK (B) ASSY, HEAD
C305 1-107-715-11 ELECT 22uF 20% 16V (RECORD/PLAY BACK/ERASE HEAD)

C311 1-162-289-31 CERAMIC 390PF 10% 50V < IC >

C313 1-162-282-31 CERAMIC 100PF 10% 50V
C314 1-130-487-00 MYLAR 0.022uF 5% 50V IC601 8-759-111-44 IC UPC4570C-1
C315 1-126-233-11 ELECT 22uF 20% 50V IC602 8-759-143-54 IC UPC1330HA
C331 1-137-427-11 FILM 120PF 5% 50V IC611 8-759-111-44 IC UPC4570C-1

C332 1-162-288-31 CERAMIC 330PF 10% 50V < COIL >

C333 1-162-209-31 CERAMIC 27PF 5% 50V
C401 1-162-289-31 CERAMIC 390PF 10% 50V L331 1-410-780-11 INDUCTOR 27mH
C402 1-126-968-11 ELECT 100uF 20% 6.3V L431 1-410-780-11 INDUCTOR 27mH
C403 1-162-282-31 CERAMIC 100PF 10% 50V L601 1-414-193-41 INDUCTOR, MICRO 22uH
L602 1-414-193-41 INDUCTOR, MICRO 22uH
C404 1-130-483-00 MYLAR 0.01uF 5% 50V
C405 1-107-715-11 ELECT 22uF 20% 16V < TRANSISTOR >
C411 1-162-289-31 CERAMIC 390PF 10% 50V
C413 1-162-282-31 CERAMIC 100PF 10% 50V Q621 8-729-142-46 TRANSISTOR 2SC2001-LK
C414 1-130-487-00 MYLAR 0.022uF 5% 50V Q622 8-729-142-46 TRANSISTOR 2SC2001-LK
Q623 8-729-801-93 TRANSISTOR 2SD1387
C415 1-126-233-11 ELECT 22uF 20% 50V
C431 1-137-427-11 FILM 120PF 5% 50V < RESISTOR >
C432 1-162-288-31 CERAMIC 330PF 10% 50V
C433 1-162-209-31 CERAMIC 27PF 5% 50V R301 1-247-881-00 CARBON 120K 5% 1/4W
C601 1-104-396-11 ELECT 10uF 20% 16V R302 1-249-409-11 CARBON 220 5% 1/4W F
R303 1-249-433-11 CARBON 22K 5% 1/4W
C602 1-104-396-11 ELECT 10uF 20% 16V R304 1-247-889-00 CARBON 270K 5% 1/4W
C611 1-104-396-11 ELECT 10uF 20% 16V R305 1-247-858-11 CARBON 13K 5% 1/4W
C612 1-104-396-11 ELECT 10uF 20% 16V
C621 1-137-150-11 FILM 0.01uF 5% 100V R311 1-247-881-00 CARBON 120K 5% 1/4W
C622 1-126-961-11 ELECT 2.2uF 20% 50V R312 1-247-807-31 CARBON 100 5% 1/4W
R314 1-247-882-11 CARBON 130K 5% 1/4W
C623 1-136-155-00 FILM 0.015uF 5% 50V R315 1-247-850-11 CARBON 6.2K 5% 1/4W
C624 1-130-481-00 MYLAR 0.0068uF 5% 50V R331 1-249-430-11 CARBON 12K 5% 1/4W
C625 1-130-481-00 MYLAR 0.0068uF 5% 50V
C627 1-124-903-11 ELECT 1uF 20% 50V R401 1-247-881-00 CARBON 120K 5% 1/4W
C628 1-136-153-00 FILM 0.01uF 5% 50V R402 1-249-409-11 CARBON 220 5% 1/4W F
R403 1-249-433-11 CARBON 22K 5% 1/4W
C642 1-104-664-11 ELECT 47uF 20% 16V R404 1-247-889-00 CARBON 270K 5% 1/4W

– 108 –
Downloaded from www.Manualslib.com manuals search engine
 AUDIO BD

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R405 1-247-858-11 CARBON 13K 5% 1/4W C123 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C124 1-126-607-11 ELECT CHIP 47uF 20% 4V
R411 1-247-881-00 CARBON 120K 5% 1/4W C125 1-164-232-11 CERAMIC CHIP 0.01uF 50V
R412 1-247-807-31 CARBON 100 5% 1/4W C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R414 1-247-882-11 CARBON 130K 5% 1/4W
R415 1-247-850-11 CARBON 6.2K 5% 1/4W C127 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
R431 1-249-430-11 CARBON 12K 5% 1/4W C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
C129 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R601 1-249-409-11 CARBON 220 5% 1/4W F C130 1-164-336-11 CERAMIC CHIP 0.33uF 25V
R602 1-249-409-11 CARBON 220 5% 1/4W F C131 1-164-346-11 CERAMIC CHIP 1uF 16V
R608 1-249-409-11 CARBON 220 5% 1/4W F
R609 1-249-433-11 CARBON 22K 5% 1/4W C140 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
R611 1-249-409-11 CARBON 220 5% 1/4W F C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C161 1-164-005-11 CERAMIC CHIP 0.47uF 25V
R612 1-249-409-11 CARBON 220 5% 1/4W F C162 1-164-232-11 CERAMIC CHIP 0.01uF 50V
!R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F C163 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
!R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
R623 1-249-432-11 CARBON 18K 5% 1/4W C164 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
R624 1-249-432-11 CARBON 18K 5% 1/4W C165 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C166 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
R625 1-249-429-11 CARBON 10K 5% 1/4W C167 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
C168 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
< VARIABLE RESISTOR >
C169 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
RV301 1-238-598-11 RES, ADJ, CARBON 2.2K C170 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K C171 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
RV341 1-241-768-11 RES, ADJ, CARBON 220K C173 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV401 1-238-598-11 RES, ADJ, CARBON 2.2K C174 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV411 1-238-598-11 RES, ADJ, CARBON 2.2K
C175 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV441 1-241-768-11 RES, ADJ, CARBON 220K C176 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C177 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< TRANSFORMER > C178 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C179 1-163-038-91 CERAMIC CHIP 0.1uF 25V
T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION
C181 1-126-205-11 ELECT CHIP 47uF 20% 6.3V
************************************************************ C182 1-126-393-11 ELECT CHIP 33uF 20% 10V
C183 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
* A-4699-522-A BD BOARD, COMPLETE C185 1-164-232-11 CERAMIC CHIP 0.01uF 50V
****************** C188 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

< CAPACITOR > C189 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

C101 1-126-607-11 ELECT CHIP 47uF 20% 4V < CONNECTOR >

C102 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P
C105 1-163-038-91 CERAMIC CHIP 0.1uF 25V CNU102 1-778-874-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P
C106 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
< FERRITE BEAD >
C107 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C108 1-164-232-11 CERAMIC CHIP 0.01uF 50V FB101 1-414-234-11 INDUCTOR CHIP 0UH
C109 1-164-232-11 CERAMIC CHIP 0.01uF 50V FB103 1-414-234-11 INDUCTOR CHIP 0UH
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C111 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V < IC >

C112 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V IC101 8-752-080-62 IC CXA1992AR

C113 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V IC102 8-759-429-32 IC BA5941FP-E2
C114 1-164-005-11 CERAMIC CHIP 0.47uF 25V IC103 8-752-378-66 IC CXD2519Q
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V
C116 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V < JUMPER RESISTOR >

C117 1-164-005-11 CERAMIC CHIP 0.47uF 25V JW101 1-216-295-91 SHORT 0

C118 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V JW104 1-216-295-91 SHORT 0
C119 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C120 1-124-779-00 ELECT CHIP 10uF 20% 16V < MOTOR >
C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V
M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
C122 1-164-232-11 CERAMIC CHIP 0.01uF 50V M102 X-4917-504-1 MOTOR ASSY (SLED)

The components identified by Les composants identifiés par une

mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.
– 109 –
Downloaded from www.Manualslib.com manuals search engine
 BD CD-SW

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< TRANSISTOR > R177 1-216-025-91 RES, CHIP 100 5% 1/10W
R178 1-216-025-91 RES, CHIP 100 5% 1/10W
Q101 8-729-010-08 TRANSISTOR MSB710-R R179 1-216-025-91 RES, CHIP 100 5% 1/10W

< RESISTOR > R180 1-216-025-91 RES, CHIP 100 5% 1/10W

R181 1-216-025-91 RES, CHIP 100 5% 1/10W
R102 1-216-001-00 METAL CHIP 10 5% 1/10W R188 1-216-037-00 METAL CHIP 330 5% 1/10W
R104 1-216-093-00 METAL CHIP 68K 5% 1/10W R190 1-216-097-91 RES, CHIP 100K 5% 1/10W
R105 1-216-088-00 METAL CHIP 43K 5% 1/10W R191 1-216-105-91 RES, CHIP 220K 5% 1/10W
R106 1-216-088-00 METAL CHIP 43K 5% 1/10W
R107 1-216-088-00 METAL CHIP 43K 5% 1/10W < SWITCH >

R108 1-216-088-00 METAL CHIP 43K 5% 1/10W S101 1-572-085-11 SWITCH, LEAF (LIMIT)
R109 1-216-093-00 METAL CHIP 68K 5% 1/10W
R114 1-216-101-00 METAL CHIP 150K 5% 1/10W < VIBRATOR >
R115 1-216-101-00 METAL CHIP 150K 5% 1/10W
R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W X101 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)

R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W ************************************************************

R118 1-216-063-91 RES, CHIP 3.9K 5% 1/10W
R119 1-216-085-00 METAL CHIP 33K 5% 1/10W * 1-668-268-11 CD-SW BOARD
R120 1-216-089-91 RES, CHIP 47K 5% 1/10W ***********
R121 1-216-114-00 RES, CHIP 510K 5% 1/10W
< DIODE >
R122 1-216-097-91 RES, CHIP 100K 5% 1/10W
R123 1-216-099-00 METAL CHIP 120K 5% 1/10W D631 8-719-056-13 DIODE SML79423C-TP15 (DISC 1)
R124 1-216-091-00 METAL CHIP 56K 5% 1/10W D632 8-719-056-13 DIODE SML79423C-TP15 (DISC 2)
R125 1-216-069-00 METAL CHIP 6.8K 5% 1/10W D633 8-719-056-13 DIODE SML79423C-TP15 (DISC 3)
R126 1-216-063-91 RES, CHIP 3.9K 5% 1/10W
< JUMPER RESISTOR >
R127 1-216-089-91 RES, CHIP 47K 5% 1/10W
R128 1-216-098-00 METAL CHIP 110K 5% 1/10W JW901 1-216-296-91 SHORT 0
R129 1-216-025-91 RES, CHIP 100 5% 1/10W JW902 1-216-295-91 SHORT 0
R130 1-216-079-00 METAL CHIP 18K 5% 1/10W
R131 1-216-079-00 METAL CHIP 18K 5% 1/10W < TRANSISTOR >

R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W Q613 8-729-027-60 TRANSISTOR DTC144TKA-T146
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W Q614 8-729-027-60 TRANSISTOR DTC144TKA-T146
R134 1-216-065-00 METAL CHIP 4.7K 5% 1/10W Q615 8-729-027-60 TRANSISTOR DTC144TKA-T146
R135 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R136 1-216-073-00 METAL CHIP 10K 5% 1/10W < RESISTOR >

R137 1-216-065-00 METAL CHIP 4.7K 5% 1/10W R656 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R138 1-216-025-91 RES, CHIP 100 5% 1/10W R657 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R156 1-216-081-00 METAL CHIP 22K 5% 1/10W R658 1-216-063-91 METAL CHIP 3.9K 5% 1/10W
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R659 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R158 1-216-001-00 METAL CHIP 10 5% 1/10W R660 1-216-071-00 RES,CHIP 8.2K 5% 1/10W

R159 1-216-121-91 RES, CHIP 1M 5% 1/10W R691 1-216-027-00 METAL CHIP 120 5% 1/10W
R161 1-216-097-91 RES, CHIP 100K 5% 1/10W R692 1-216-027-00 METAL CHIP 120 5% 1/10W
R162 1-216-073-00 METAL CHIP 10K 5% 1/10W R693 1-216-027-00 METAL CHIP 120 5% 1/10W
R163 1-216-121-91 RES, CHIP 1M 5% 1/10W R694 1-216-027-00 METAL CHIP 120 5% 1/10W
R164 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R695 1-216-027-00 METAL CHIP 120 5% 1/10W

R165 1-216-049-91 RES, CHIP 1K 5% 1/10W R696 1-216-027-00 METAL CHIP 120 5% 1/10W
R166 1-216-073-00 METAL CHIP 10K 5% 1/10W
R167 1-216-081-00 METAL CHIP 22K 5% 1/10W < SWITCH >
R168 1-216-073-00 METAL CHIP 10K 5% 1/10W
R169 1-216-079-00 METAL CHIP 18K 5% 1/10W S637 1-762-875-21 SWITCH, KEYBOARD (1/u)
S638 1-762-875-21 SWITCH, KEYBOARD (DISC 1)
R170 1-216-081-00 METAL CHIP 22K 5% 1/10W S639 1-762-875-21 SWITCH, KEYBOARD (DISC 2)
R171 1-216-073-00 METAL CHIP 10K 5% 1/10W S640 1-762-875-21 SWITCH, KEYBOARD (DISC 3)
R172 1-216-079-00 METAL CHIP 18K 5% 1/10W S641 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)
R173 1-216-025-91 RES, CHIP 100 5% 1/10W
R174 1-216-033-00 METAL CHIP 220 5% 1/10W S642 1-762-875-21 SWITCH, KEYBOARD (§)

R175 1-216-025-91 RES, CHIP 100 5% 1/10W **************************************************************

R176 1-216-025-91 RES, CHIP 100 5% 1/10W

– 110 –
Downloaded from www.Manualslib.com manuals search engine
 CONNECTOR CONT COM DECO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-658-575-11 CONNECTOR BOARD R668 1-216-029-00 METAL CHIP 150 5% 1/10W
****************
R669 1-216-019-00 METAL CHIP 56 5% 1/10W
< CONNECTOR > R670 1-216-037-00 METAL CHIP 330 5% 1/10W
R671 1-216-019-00 METAL CHIP 56 5% 1/10W
* CN701 1-568-946-11 PIN, CONNECTOR 8P R811 1-216-029-00 METAL CHIP 150 5% 1/10W
CN702 1-750-413-11 CONNECTOR, FFC/FPC 8P R812 1-216-029-00 METAL CHIP 150 5% 1/10W

< TRANSISTOR > R813 1-216-029-00 METAL CHIP 150 5% 1/10W

R814 1-216-029-00 METAL CHIP 150 5% 1/10W
Q701 8-729-900-80 TRANSISTOR DTC114ES R821 1-216-039-00 METAL CHIP 390 5% 1/10W
R822 1-216-041-00 METAL CHIP 470 5% 1/10W
< RESISTOR > R823 1-216-045-00 METAL CHIP 680 5% 1/10W

R703 1-249-435-11 CARBON 33K 5% 1/4W R831 1-216-039-00 METAL CHIP 390 5% 1/10W
R704 1-249-429-11 CARBON 10K 5% 1/4W R832 1-216-041-00 METAL CHIP 470 5% 1/10W
R705 1-249-417-11 CARBON 1K 5% 1/4W F R833 1-216-045-00 METAL CHIP 680 5% 1/10W

************************************************************ < SWITCH >

* A-4407-476-A CONT COM BOARD, COMPLETE S601 1-473-534-11 ENCODER, ROTARY (JOG)
************************* S602 1-473-392-11 ENCODER, ROTARY (VOLUME)
S617 1-762-875-21 SWITCH, KEYBOARD (LOOP)
< CAPACITOR > S618 1-762-875-21 SWITCH, KEYBOARD (FLASH)
S619 1-762-875-21 SWITCH, KEYBOARD (NON-STOP)
C627 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C628 1-164-232-11 CERAMIC CHIP 0.01uF 50V S621 1-762-875-21 SWITCH, KEYBOARD (– 0)
C629 1-164-232-11 CERAMIC CHIP 0.01uF 50V S622 1-762-875-21 SWITCH, KEYBOARD (ENTER/NEXT)
C630 1-164-232-11 CERAMIC CHIP 0.01uF 50V S623 1-762-875-21 SWITCH, KEYBOARD (+ ))
S624 1-762-875-21 SWITCH, KEYBOARD (DBFB)
< CONNECTOR > S625 1-762-875-21 SWITCH, KEYBOARD (GROOVE)

* CN608 1-568-862-11 SOCKET, CONNECTOR 19P S801 1-762-875-21 SWITCH, KEYBOARD (PAD-B)
S802 1-762-875-21 SWITCH, KEYBOARD (AUTO BPM)
< DIODE > S803 1-762-875-21 SWITCH, KEYBOARD (JAM-BEAT)
S804 1-762-875-21 SWITCH, KEYBOARD (BEAT LEVEL)
D610 8-719-063-93 DIODE SLR325VC-N-T32 (ENTER/NEXT) S805 1-762-875-21 SWITCH, KEYBOARD (PAD-A)
D612 8-719-057-97 DIODE SEL5923A-TP15 (GROOVE)
D613 8-719-063-93 DIODE SLR325VC-N-T32 (JOG) S806 1-762-875-21 SWITCH, KEYBOARD (ON/OFF-BEAT)
D614 8-719-064-65 DIODE SELU5723C-TP15 (DJ MIX) S807 1-762-875-21 SWITCH, KEYBOARD (SELECT-BEAT)
D615 8-719-064-65 DIODE SELU5723C-TP15 (DJ MIX) S808 1-762-875-21 SWITCH, KEYBOARD (SPEED-BEAT)

D616 8-719-063-93 DIODE SLR325VC-N-T32 (NON-STOP) < CONNECTOR >

D617 8-719-057-97 DIODE SEL5923A-TP15 (– 0)
D618 8-719-057-97 DIODE SEL5923A-TP15 (+ )) W601 1-775-377-11 LEAD (WITH CONNECTOR)
D801 8-719-057-97 DIODE SEL5923A-TP15 (ON/OFF)
D802 8-719-057-97 DIODE SEL5923A-TP15 (JAM) **************************************************************

D803 8-719-056-13 DIODE SML79423C-TP15 (AUTO BPM) * 1-668-269-11 DECO BOARD

**********
< TRANSISTOR >
< DIODE >
Q604 8-729-027-60 TRANSISTOR DTC144TKA-T146
Q854 8-729-027-23 TRANSISTOR DTA114EKA-T146 D640 8-719-063-93 DIODE SLR325VC-N-T32 (CENTER)
Q855 8-729-027-23 TRANSISTOR DTA114EKA-T146 D641 8-719-032-86 DIODE SEL5420E (LEFT)
D642 8-719-032-86 DIODE SEL5420E (LEFT)
< RESISTOR > D643 8-719-032-86 DIODE SEL5420E (LEFT)
D644 8-719-033-06 DIODE SEL5920A (CENTER)
R637 1-216-039-00 METAL CHIP 390 5% 1/10W
R638 1-216-041-00 METAL CHIP 470 5% 1/10W D655 8-719-033-06 DIODE SEL5920A (RIGHT)
R639 1-216-045-00 METAL CHIP 680 5% 1/10W D656 8-719-033-06 DIODE SEL5920A (RIGHT)
R640 1-216-047-91 RES,CHIP 820 5% 1/10W
R641 1-216-051-00 METAL CHIP 1.2K 5% 1/10W < TRANSISTOR >

R642 1-216-053-91 RES,CHIP 1.5K 5% 1/10W Q856 8-729-027-60 TRANSISTOR DTC144TKA-T146

R643 1-216-057-00 METAL CHIP 2.2K 5% 1/10W Q857 8-729-027-60 TRANSISTOR DTC144TKA-T146
R666 1-216-037-00 METAL CHIP 330 5% 1/10W
R667 1-216-029-00 METAL CHIP 150 5% 1/10W

– 111 –
Downloaded from www.Manualslib.com manuals search engine
 DECO HP LEAF SW MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR > R1002 1-249-409-11 CARBON 220 5% 1/4W F
R1003 1-249-414-11 CARBON 560 5% 1/4W F
R706 1-216-019-00 METAL CHIP 56 5% 1/10W R1004 1-247-834-11 CARBON 1.3K 5% 1/4W
R707 1-216-019-00 METAL CHIP 56 5% 1/10W
R708 1-216-041-00 METAL CHIP 470 5% 1/10W R1005 1-247-818-11 CARBON 300 5% 1/4W
R709 1-216-027-00 METAL CHIP 120 5% 1/10W R1006 1-247-864-11 CARBON 24K 5% 1/4W
R710 1-216-027-00 METAL CHIP 120 5% 1/10W R1007 1-247-856-00 CARBON 11K 5% 1/4W
R1008 1-249-417-11 CARBON 1K 5% 1/4W F
**************************************************************
< VARIABLE RESISTOR >
* 1-668-271-11 HP BOARD
******** RV1001 1-241-785-11 RES, ADJ, CARBON 10K
RV1002 1-241-785-11 RES, ADJ, CARBON 10K
< CAPACITOR >
< SWITCH >
C790 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C791 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V S1001 1-570-953-11 SWITCH, PUSH (1 KEY) (A PLAY)
C792 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V S1002 1-570-953-11 SWITCH, PUSH (1 KEY) (B PLAY)
S1003 1-771-333-11 SWITCH, LEAF (A HALF)
< CONNECTOR > S1004 1-771-205-11 SWITCH, LEAF (A 120/70)
S1005 1-771-205-11 SWITCH, LEAF (REC A)
CN752 1-506-469-11 PIN, CONNECTOR 4P
S1006 1-771-333-11 SWITCH, LEAF (B HALF)
< GROUND PLATE > S1008 1-771-205-11 SWITCH, LEAF (B 120/70)
S1009 1-771-205-11 SWITCH, LEAF (REC B)
* EP751 1-537-738-21 TERMINAL, EARTH
************************************************************
< JACK >
* A-4407-262-A MAIN BOARD, COMPLETE (RX110AV:AEP,UK,G)
J755 1-784-224-11 JACK (LARGE TYPE)(PHONES) ********************

************************************************************** * A-4407-280-A MAIN BOARD, COMPLETE (RX110AV:EE,CIS)

********************
* A-2007-732-A LEAF SW BOARD, COMPLETE
************************ * A-4407-284-A MAIN BOARD, COMPLETE
********************
< CAPACITOR > (GRX10AV:E3,SP,MY,HK,EA)

C1001 1-128-124-11 ELECT 33uF 20% 10V * A-4407-286-A MAIN BOARD, COMPLETE (GRX10AV:E2)
********************
< CONNECTOR >
* A-4407-314-A MAIN BOARD, COMPLETE (RX110AV:CND)
CN1001 1-568-860-11 SOCKET, CONNECTOR 17P ********************
CN1001 1-784-459-11 CONNECTOR, FFC/FPC 17P
* A-4407-755-A MAIN BOARD, COMPLETE (GRX10AV:TH)
< DIODE > ********************

D1001 8-719-911-19 DIODE 1SS119 * A-4407-768-A MAIN BOARD, COMPLETE (GRX10AV:AUS)

D1002 8-719-911-19 DIODE 1SS119 ********************

< CONNECTOR > 7-685-646-79SCREW +BVTP 3X8 TYPE2 N-S

* DM1001 1-784-581-11 HOLDER, CABLE (2.5MM PITCH) 4P

< CAPACITOR >
< IC >
C101 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
IC1001 8-749-014-38 IC PHOTO INTERRUPTER SG-264 C102 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
IC1002 8-749-014-38 IC PHOTO INTERRUPTER SG-264 C103 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
C111 1-137-195-11 FILM 0.56uF 5% 50V
< TRANSISTOR > C112 1-163-986-00 CERAMIC CHIP 0.027uF 10% 25V

Q1001 8-729-029-56 TRANSISTOR DTA144ESA C113 1-136-167-00 FILM 0.15uF 5% 50V

Q1001 8-729-900-65 TRANSISTOR DTA144ES C114 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V
C115 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
< RESISTOR > C116 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
C117 1-164-232-11 CERAMIC CHIP 0.01uF 50V
R907 1-247-879-11 CARBON 100K 5% 1/4W
R1001 1-249-409-11 CARBON 220 5% 1/4W F C118 1-163-003-11 CERAMIC CHIP 330PF 10% 50V

– 112 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C119 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C215 1-126-934-11 ELECT 220uF 20% 16V
C120 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V C216 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C121 1-126-964-11 ELECT 10uF 20% 50V
C122 1-163-006-11 CERAMIC CHIP 560PF 10% 50V C217 1-136-165-00 FILM 0.1uF 5% 50V
C218 1-126-960-11 ELECT 1uF 20% 50V
C123 1-136-169-00 FILM 0.22uF 5% 50V C219 1-126-961-11 ELECT 2.2uF 20% 50V
C124 1-136-169-00 FILM 0.22uF 5% 50V C220 1-126-960-11 ELECT 1uF 20% 50V
C125 1-126-964-11 ELECT 10uF 20% 50V C221 1-136-165-00 FILM 0.1uF 5% 50V
C131 1-126-933-11 ELECT 100uF 20% 10V
C132 1-126-933-11 ELECT 100uF 20% 10V C222 1-126-961-11 ELECT 2.2uF 20% 50V
C223 1-124-252-00 ELECT 0.33uF 20% 50V
C133 1-163-038-91 CERAMIC CHIP 0.1uF 25V C224 1-126-959-11 ELECT 0.47uF 20% 50V
C134 1-163-038-91 CERAMIC CHIP 0.1uF 25V C225 1-136-164-00 FILM 0.082uF 5% 50V
C135 1-126-964-11 ELECT 10uF 20% 50V C226 1-130-477-00 MYLAR 0.0033uF 5% 50V
C136 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C137 1-163-038-91 CERAMIC CHIP 0.1uF 25V C227 1-136-164-00 FILM 0.082uF 5% 50V
C228 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C141 1-109-953-11 ELECT 2.2uF 20% 50V C229 1-126-934-11 ELECT 220uF 20% 10V
C151 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C230 1-130-469-00 MYLAR 680PF 5% 50V
C152 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C231 1-136-161-00 FILM 0.047uF 5% 50V
C153 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
C154 1-163-038-91 CERAMIC CHIP 0.1uF 25V C232 1-136-157-00 FILM 0.022uF 5% 50V
C233 1-136-173-00 FILM 0.47uF 5% 50V
C161 1-137-195-11 FILM 0.56uF 5% 50V C234 1-126-967-11 ELECT 47uF 20% 10V
C162 1-163-986-00 CERAMIC CHIP 0.027uF 10% 25V C235 1-126-961-11 ELECT 2.2uF 20% 50V
C163 1-136-167-00 FILM 0.15uF 5% 50V C236 1-126-961-11 ELECT 2.2uF 20% 50V
C164 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V
C165 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V C237 1-136-165-00 FILM 0.1uF 5% 50V
C238 1-136-165-00 FILM 0.1uF 5% 50V
C166 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V C239 1-126-959-11 ELECT 0.47uF 20% 50V
C167 1-164-232-11 CERAMIC CHIP 0.01uF 50V C240 1-126-963-11 ELECT 4.7uF 20% 50V
C168 1-163-003-11 CERAMIC CHIP 330PF 10% 50V C241 1-126-959-11 ELECT 0.47uF 20% 50V
C169 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C170 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V C242 1-126-963-11 ELECT 4.7uF 20% 50V
C243 1-136-167-00 FILM 0.15uF 5% 50V
C171 1-126-964-11 ELECT 10uF 20% 50V C244 1-126-962-11 ELECT 3.3uF 20% 50V
C172 1-163-006-11 CERAMIC CHIP 560PF 10% 50V C245 1-136-167-00 FILM 0.15uF 5% 50V
C173 1-136-169-00 FILM 0.22uF 5% 50V C246 1-136-167-00 FILM 0.15uF 5% 50V
C174 1-136-169-00 FILM 0.22uF 5% 50V
C175 1-126-964-11 ELECT 10uF 20% 50V C247 1-126-962-11 ELECT 3.3uF 20% 50V
C248 1-136-167-00 FILM 0.15uF 5% 50V
C176 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V C249 1-126-963-11 ELECT 4.7uF 20% 50V
C177 1-164-232-11 CERAMIC CHIP 0.01uF 50V C250 1-126-959-11 ELECT 0.47uF 20% 50V
C191 1-126-964-11 ELECT 10uF 20% 50V C251 1-126-963-11 ELECT 4.7uF 20% 50V
C192 1-163-007-11 CERAMIC CHIP 680PF 10% 50V
C193 1-126-964-11 ELECT 10uF 20% 50V C252 1-126-959-11 ELECT 0.47uF 20% 50V
C254 1-126-934-11 ELECT 220uF 20% 16V
C194 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C255 1-136-165-00 FILM 0.1uF 5% 50V
C195 1-163-038-91 CERAMIC CHIP 0.1uF 25V C256 1-126-934-11 ELECT 220uF 20% 16V
C196 1-163-038-91 CERAMIC CHIP 0.1uF 25V C291 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C197 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C201 1-136-165-00 FILM 0.1uF 5% 50V C292 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C293 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C202 1-136-165-00 FILM 0.1uF 5% 50V C294 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C203 1-126-964-11 ELECT 10uF 20% 50V C295 1-126-964-11 ELECT 10uF 20% 50V
C204 1-126-964-11 ELECT 10uF 20% 50V C296 1-126-964-11 ELECT 10uF 20% 50V
C205 1-126-964-11 ELECT 10uF 20% 50V
C206 1-126-964-11 ELECT 10uF 20% 50V C301 1-126-960-11 ELECT 1uF 20% 50V
C302 1-130-479-00 MYLAR 0.0047uF 5% 50V
C207 1-126-934-11 ELECT 220uF 20% 10V C303 1-136-165-00 FILM 0.1uF 5% 50V
C208 1-126-934-11 ELECT 220uF 20% 16V C304 1-136-165-00 FILM 0.1uF 5% 50V
C209 1-163-038-91 CERAMIC CHIP 0.1uF 25V C305 1-126-964-11 ELECT 10uF 20% 50V
C210 1-126-961-11 ELECT 2.2uF 20% 50V
C211 1-126-934-11 ELECT 220uF 20% 10V C306 1-126-960-11 ELECT 1uF 20% 50V
C307 1-126-959-11 ELECT 0.47uF 20% 50V
C212 1-126-961-11 ELECT 2.2uF 20% 50V C308 1-126-964-11 ELECT 10uF 20% 50V
C213 1-126-964-11 ELECT 10uF 20% 50V C309 1-136-173-00 FILM 0.47uF 5% 50V
C214 1-126-964-11 ELECT 10uF 20% 50V C310 1-163-005-11 CERAMIC CHIP 470PF 10% 50V

– 113 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C311 1-126-964-11 ELECT 10uF 20% 50V C902 1-126-943-11 ELECT 2200uF 20% 25V
C312 1-126-959-11 ELECT 0.47uF 20% 50V (GRX10AV)
C313 1-130-471-00 MYLAR 0.001uF 5% 50V
C314 1-126-964-11 ELECT 10uF 20% 50V C903 1-126-964-11 ELECT 10uF 20% 50V
C315 1-126-963-11 ELECT 4.7uF 20% 50V C904 1-126-964-11 ELECT 10uF 20% 50V
C905 1-126-933-11 ELECT 100uF 20% 10V
C316 1-126-933-11 ELECT 100uF 20% 10V C906 1-126-933-11 ELECT 100uF 20% 10V
C317 1-126-933-11 ELECT 100uF 20% 10V C907 1-126-925-11 ELECT 470uF 20% 10V
C320 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C331 1-163-038-91 CERAMIC CHIP 0.1uF 25V C908 1-126-925-11 ELECT 470uF 20% 10V
C332 1-163-038-91 CERAMIC CHIP 0.1uF 25V C911 1-126-964-11 ELECT 10uF 20% 50V
C912 1-126-768-11 ELECT 2200uF 20% 16V
C333 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C921 1-126-964-11 ELECT 10uF 20% 50V
C334 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C922 1-126-767-11 ELECT 1000uF 20% 16V
C351 1-126-960-11 ELECT 1uF 20% 50V
C352 1-130-479-00 MYLAR 0.0047uF 5% 50V C931 1-126-964-11 ELECT 10uF 20% 50V
C353 1-136-165-00 FILM 0.1uF 5% 50V C932 1-126-916-11 ELECT 1000uF 20% 6.3V
C933 1-104-656-11 ELECT 2200uF 20% 6.3V
C354 1-136-165-00 FILM 0.1uF 5% 50V C934 1-126-933-11 ELECT 100uF 20% 10V
C355 1-126-964-11 ELECT 10uF 20% 50V C941 1-126-964-11 ELECT 10uF 20% 50V
C356 1-126-960-11 ELECT 1uF 20% 50V
C357 1-126-959-11 ELECT 0.47uF 20% 50V C942 1-126-933-11 ELECT 100uF 20% 10V
C358 1-126-964-11 ELECT 10uF 20% 50V C951 1-126-967-11 ELECT 47uF 20% 10V
C952 1-136-165-00 FILM 0.1uF 5% 50V
C359 1-136-173-00 FILM 0.47uF 5% 50V C953 1-136-173-00 FILM 0.47uF 5% 50V
C371 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C961 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C372 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C373 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C991 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C374 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
< CONNECTOR >
C375 1-163-038-91 CERAMIC CHIP 0.1uF 25V
(RX110AV:EE,CIS) * CN101 1-568-832-11 SOCKET, CONNECTOR 13P
C376 1-163-038-91 CERAMIC CHIP 0.1uF 25V
(RX110AV:EE,CIS) CN102 1-784-600-11 SOCKET, CONNECTOR (NON ZIF)15P
C381 1-163-251-11 CERAMIC CHIP 100PF 5% 50V (GRX10AV:E3,SP,MY,HK,EA/RX110AV:EXCEPT CND)
C382 1-126-925-11 ELECT 470uF 20% 10V CN102 1-784-601-11 SOCKET, CONNECTOR (NON ZIF) 13P
C383 1-163-038-91 CERAMIC CHIP 0.1uF 25V (GRX10AV:E2,TH,AUS/RX110AV:CND)
* CN103 1-568-946-11 PIN, CONNECTOR 8P
C384 1-163-038-91 CERAMIC CHIP 0.1uF 25V * CN104 1-568-947-11 PIN, CONNECTOR 9P
C385 1-126-961-11 ELECT 2.2uF 20% 50V
C386 1-126-961-11 ELECT 2.2uF 20% 50V CN105 1-764-698-11 SOCKET, CONNECTOR (NON ZIF) 19P
C387 1-163-005-11 CERAMIC CHIP 470PF 10% 50V CN106 1-568-834-11 SOCKET, CONNECTOR 15P
C388 1-163-005-11 CERAMIC CHIP 470PF 10% 50V * CN107 1-568-836-11 SOCKET, CONNECTOR 17P
* CN301 1-568-449-11 HOUSING, CONNECTOR(PC BOARD) 3P
C391 1-163-038-91 CERAMIC CHIP 0.1uF 25V CN901 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P
C392 1-126-933-11 ELECT 100uF 20% 10V
C401 1-163-038-91 CERAMIC CHIP 0.1uF 25V CN902 1-770-728-11 CONNECTOR, BOARD TO BOARD 9P
C402 1-163-038-91 CERAMIC CHIP 0.1uF 25V * CN961 1-564-518-11 PLUG, CONNECTOR 3P
C403 1-126-964-11 ELECT 10uF 20% 50V
< DIODE >
C411 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C412 1-163-038-91 CERAMIC CHIP 0.1uF 25V D381 8-719-988-62 DIODE 1SS355
C414 1-126-964-11 ELECT 10uF 20% 50V D382 8-719-988-62 DIODE 1SS355
C415 1-126-964-11 ELECT 10uF 20% 50V D502 8-719-988-62 DIODE 1SS355
C501 1-126-916-11 ELECT 1000uF 20% 6.3V D508 8-719-988-62 DIODE 1SS355
D901 8-719-988-62 DIODE 1SS355
C502 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C503 1-163-235-11 CERAMIC CHIP 22PF 5% 50V D921 8-719-210-33 DIODE EC10DS2
C504 1-163-235-11 CERAMIC CHIP 22PF 5% 50V D931 8-719-988-62 DIODE 1SS355
C505 1-163-038-91 CERAMIC CHIP 0.1uF 25V D932 8-719-210-33 DIODE EC10DS2
C506 1-126-933-11 ELECT 100uF 20% 10V D951 8-719-988-62 DIODE 1SS355
D952 8-719-988-62 DIODE 1SS355
C508 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C901 1-126-937-11 ELECT 4700uF 20% 16V D953 8-719-988-62 DIODE 1SS355
(RX110AV) D954 8-719-988-62 DIODE 1SS355
C901 1-128-548-11 ELECT 4700uF 20% 25V D955 8-719-210-33 DIODE EC10DS2
(GRX10AV) D956 8-719-988-62 DIODE 1SS355
C902 1-126-768-11 ELECT 2200uF 20% 16V
(RX110AV)

– 114 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< GROUND TERMINAL > Q113 8-729-141-30 TRANSISTOR 2SC3623A-LK
Q141 8-729-422-57 TRANSISTOR UN4111
* EPT901 4-870-539-11 PLATE, GROUND Q142 8-729-900-36 TRANSISTOR DTC124ES

< COIL > Q143 8-729-119-76 TRANSISTOR 2SA1175-HFE

Q161 8-729-119-78 TRANSISTOR 2SC403SP-51
FB381 1-414-234-11 INDUCTOR CHIP 0UH Q162 8-729-119-78 TRANSISTOR 2SC403SP-51
Q163 8-729-141-30 TRANSISTOR 2SC3623A-LK
< FILTER > Q191 8-729-141-30 TRANSISTOR 2SC3623A-LK

FL131 1-233-289-21 FILTER, EMI (SMD) Q291 8-729-141-30 TRANSISTOR 2SC3623A-LK

FL241 1-233-289-21 FILTER, EMI (SMD) Q292 8-729-141-30 TRANSISTOR 2SC3623A-LK
FL501 1-233-289-21 FILTER, EMI (SMD) Q331 8-729-118-00 TRANSISTOR 2SB1116-L
FL502 1-233-289-21 FILTER, EMI (SMD) Q332 8-729-900-80 TRANSISTOR DTC114ES
Q333 8-729-118-00 TRANSISTOR 2SB1116-L
< IC >
Q334 8-729-900-80 TRANSISTOR DTC114ES
IC111 8-759-495-24 IC M62442FP-TP Q335 8-729-900-80 TRANSISTOR DTC114ES
IC191 8-759-636-55 IC M5218AFP Q336 8-729-116-57 TRANSISTOR 2SB1068-K
IC201 8-759-526-39 IC LV1041M Q337 8-729-144-44 TRANSISTOR 2SD1513
IC291 8-759-636-55 IC M5218AFP Q338 8-729-422-57 TRANSISTOR UN4111
IC301 8-759-495-26 IC HA12215
Q339 8-729-900-80 TRANSISTOR DTC114ES
IC391 8-749-923-04 IC TOTX178 (CD DIGITAL OUT OPTICAL) Q340 8-729-166-57 TRANSISTOR 2SB1068-K
IC401 8-759-636-55 IC M5218AFP Q341 8-729-144-44 TRANSISTOR 2SD1513
IC411 8-759-636-55 IC M5218AFP Q342 8-729-422-57 TRANSISTOR UN4111
IC501 8-759-537-36 IC uPD780018AYGF-012-3BA Q343 8-729-900-80 TRANSISTOR DTC114ES
IC901 8-759-604-86 IC M5F7807L
Q411 8-729-141-30 TRANSISTOR 2SC3623A-LK
IC902 8-759-604-90 IC M5F7907L Q901 8-729-040-20 TRANSISTOR RT1P137L-TP
IC911 8-759-231-58 IC TA7812S Q902 8-729-900-36 TRANSISTOR DTC124ES
IC921 8-759-604-38 IC M5F78M10 Q903 8-729-040-19 TRANSISTOR RT1N137L-TP
IC931 8-759-231-53 IC TA7805S Q904 8-729-900-63 TRANSISTOR DTA124ES
IC941 8-759-604-86 IC M5F7807L
Q905 8-729-119-76 TRANSISTOR 2SA1175-HFE
IC951 8-759-635-63 IC M51943BSL Q911 8-729-141-83 TRANSISTOR 2SB1094-LK
Q912 8-729-900-36 TRANSISTOR DTC124ES
< JACK > Q913 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q931 8-729-040-20 TRANSISTOR RT1P137L-TP
J101 1-774-411-11 JACK, PIN 6P
(VIDEO(AUDIO) IN, MD IN, MD/VIDEO (AUDIO) OUT) Q932 8-729-900-36 TRANSISTOR DTC124ES
J191 1-774-785-11 JACK, PIN 1P (SUPER WOOFER) Q933 8-729-040-20 TRANSISTOR RT1P137L-TP
Q934 8-729-900-63 TRANSISTOR DTA124ES
< JUMPER RESISTOR > Q937 8-729-900-36 TRANSISTOR DTC124ES
Q951 8-729-119-78 TRANSISTOR 2SC403SP-51
JR1 1-216-295-91 SHORT 0
JR2 1-216-295-91 SHORT 0 Q961 8-729-111-29 TRANSISTOR 2SD1616A-K
JR4 1-216-295-91 SHORT 0 Q962 8-729-119-76 TRANSISTOR 2SA1175-HFE
JR5 1-216-295-91 SHORT 0
JR201 1-216-296-91 SHORT 0 < RESISTOR >

JR202 1-216-296-91 SHORT 0 R101 1-216-049-91 RES,CHIP 1K 5% 1/10W

R102 1-216-105-91 RES,CHIP 220K 5% 1/10W
< COIL > R103 1-216-049-91 RES,CHIP 1K 5% 1/10W
R104 1-216-105-91 RES,CHIP 220K 5% 1/10W
L241 1-412-032-11 INDUCTOR CHIP 100uH R105 1-216-049-91 RES,CHIP 1K 5% 1/10W
L371 1-412-032-11 INDUCTOR CHIP 100uH (RX110AV:AEP,UK,G)
L372 1-412-032-11 INDUCTOR CHIP 100uH R106 1-216-097-91 RES,CHIP 100K 5% 1/10W
L391 1-412-032-11 INDUCTOR CHIP 100uH R111 1-216-073-00 METAL CHIP 10K 5% 1/10W
L569 1-412-032-11 INDUCTOR CHIP 100uH R112 1-216-121-91 RES,CHIP 1M 5% 1/10W
R113 1-216-111-00 METAL CHIP 390K 5% 1/10W
L570 1-412-032-11 INDUCTOR CHIP 100uH R114 1-216-044-00 METAL CHIP 620 5% 1/10W
L572 1-412-032-11 INDUCTOR CHIP 100uH
R115 1-216-073-00 METAL CHIP 10K 5% 1/10W
< TRANSISTOR > R116 1-216-097-91 RES,CHIP 100K 5% 1/10W
R117 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q111 8-729-119-78 TRANSISTOR 2SC403SP-51 R118 1-216-089-91 RES,CHIP 47K 5% 1/10W
Q112 8-729-119-78 TRANSISTOR 2SC403SP-51 R119 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

– 115 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R120 1-216-097-91 RES,CHIP 100K 5% 1/10W R253 1-216-097-91 RES,CHIP 100K 5% 1/10W
R121 1-216-073-00 METAL CHIP 10K 5% 1/10W R254 1-216-097-91 RES,CHIP 100K 5% 1/10W
R122 1-216-295-91 SHORT 0 R255 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R123 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R131 1-216-025-91 RES,CHIP 100 5% 1/10W R256 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R257 1-216-025-91 RES,CHIP 100 5% 1/10W
R132 1-216-025-91 RES,CHIP 100 5% 1/10W R258 1-216-025-91 RES,CHIP 100 5% 1/10W
R133 1-216-025-91 RES,CHIP 100 5% 1/10W R259 1-216-085-91 RES,CHIP 33K 5% 1/10W
R134 1-216-089-91 RES,CHIP 47K 5% 1/10W R260 1-216-085-91 RES,CHIP 33K 5% 1/10W
R135 1-216-089-91 RES,CHIP 47K 5% 1/10W
R136 1-216-089-91 RES,CHIP 47K 5% 1/10W R261 1-216-073-00 METAL CHIP 10K 5% 1/10W
R262 1-216-073-00 METAL CHIP 10K 5% 1/10W
R137 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R263 1-216-077-00 METAL CHIP 15K 5% 1/10W
R138 1-216-089-91 RES,CHIP 47K 5% 1/10W R264 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R141 1-216-049-91 RES,CHIP 1K 5% 1/10W R301 1-216-085-00 METAL CHIP 33K 5% 1/10W
R142 1-216-097-91 RES,CHIP 100K 5% 1/10W
R143 1-216-049-91 RES,CHIP 1K 5% 1/10W R302 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R303 1-216-025-91 RES,CHIP 100 5% 1/10W
R144 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R304 1-216-025-91 RES,CHIP 100 5% 1/10W
R151 1-216-049-91 RES,CHIP 1K 5% 1/10W R305 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R152 1-216-105-91 RES,CHIP 220K 5% 1/10W R306 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R153 1-216-049-91 RES,CHIP 1K 5% 1/10W
R154 1-216-105-91 RES,CHIP 220K 5% 1/10W R307 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R308 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R155 1-216-049-91 RES,CHIP 1K 5% 1/10W R309 1-216-081-00 METAL CHIP 22K 5% 1/10W
R156 1-216-097-91 RES,CHIP 100K 5% 1/10W R311 1-216-121-91 RES,CHIP 1M 5% 1/10W
R161 1-216-073-00 METAL CHIP 10K 5% 1/10W R312 1-216-102-00 RES,CHIP 160K 5% 1/10W
R162 1-216-121-91 RES,CHIP 1M 5% 1/10W
R163 1-216-111-91 RES,CHIP 390K 5% 1/10W R313 1-216-097-91 RES,CHIP 100K 5% 1/10W
R315 1-216-073-00 METAL CHIP 10K 5% 1/10W
R164 1-216-044-00 METAL CHIP 620 5% 1/10W R316 1-216-079-00 METAL CHIP 18K 5% 1/10W
R165 1-216-073-00 METAL CHIP 10K 5% 1/10W R317 1-216-073-00 METAL CHIP 10K 5% 1/10W
R166 1-216-097-91 RES,CHIP 100K 5% 1/10W R318 1-216-073-00 METAL CHIP 10K 5% 1/10W
R167 1-216-073-00 METAL CHIP 10K 5% 1/10W
R168 1-216-089-91 RES,CHIP 47K 5% 1/10W R319 1-216-111-91 RES,CHIP 390K 5% 1/10W
R321 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R169 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R322 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R170 1-216-097-91 RES,CHIP 100K 5% 1/10W R324 1-216-094-00 RES,CHIP 75K 5% 1/10W
R171 1-216-073-00 METAL CHIP 10K 5% 1/10W R325 1-216-089-91 RES,CHIP 47K 5% 1/10W
R172 1-216-295-91 SHORT 0
R173 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R326 1-216-089-91 RES,CHIP 47K 5% 1/10W
R327 1-216-089-91 RES,CHIP 47K 5% 1/10W
R191 1-216-089-91 RES,CHIP 47K 5% 1/10W R328 1-216-094-00 RES,CHIP 75K 5% 1/10W
R192 1-216-089-91 RES,CHIP 47K 5% 1/10W R329 1-216-049-91 RES,CHIP 1K 5% 1/10W
R193 1-216-089-91 RES,CHIP 47K 5% 1/10W R330 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R194 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R195 1-216-073-00 METAL CHIP 10K 5% 1/10W R331 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R332 1-216-045-00 METAL CHIP 680 5% 1/10W
R196 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R333 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R197 1-216-097-91 RES,CHIP 100K 5% 1/10W R334 1-216-045-00 METAL CHIP 680 5% 1/10W
R198 1-216-049-91 RES,CHIP 1K 5% 1/10W R335 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R199 1-216-073-00 METAL CHIP 10K 5% 1/10W
R201 1-216-081-00 METAL CHIP 22K 5% 1/10W R336 1-216-089-91 RES,CHIP 47K 5% 1/10W
R337 1-216-049-91 RES, CHIP 1K 5% 1/10W
R202 1-216-082-91 RES, CHIP 24K 5% 1/10W R338 1-216-037-00 METAL CHIP 330 5% 1/10W
R203 1-216-689-11 METAL CHIP 39K 0.5% 1/10W R339 1-216-089-91 RES,CHIP 47K 5% 1/10W
R204 1-216-121-91 RES,CHIP 1M 5% 1/10W R340 1-216-089-91 RES,CHIP 47K 5% 1/10W
R205 1-216-033-00 METAL CHIP 220 5% 1/10W
R206 1-216-025-91 RES,CHIP 100 5% 1/10W R341 1-216-037-00 METAL CHIP 330 5% 1/10W
R342 1-216-089-91 RES,CHIP 47K 5% 1/10W
R207 1-216-025-91 RES,CHIP 100 5% 1/10W R343 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R208 1-216-025-91 RES,CHIP 100 5% 1/10W R344 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R209 1-216-025-91 RES,CHIP 100 5% 1/10W R351 1-216-085-00 METAL CHIP 33K 5% 1/10W
R241 1-216-082-91 RES, CHIP 24K 5% 1/10W
R242 1-216-082-91 RES, CHIP 24K 5% 1/10W R352 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R353 1-216-025-91 RES,CHIP 100 5% 1/10W
R251 1-216-049-91 RES,CHIP 1K 5% 1/10W R354 1-216-025-91 RES,CHIP 100 5% 1/10W
R252 1-216-049-91 RES,CHIP 1K 5% 1/10W R355 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

– 116 –
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R356 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R580 1-216-025-91 RES,CHIP 100 5% 1/10W

R357 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R581 1-216-025-91 RES,CHIP 100 5% 1/10W
R358 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R595 1-216-025-91 RES,CHIP 100 5% 1/10W
R359 1-216-085-00 METAL CHIP 33K 5% 1/10W R596 1-216-025-91 RES,CHIP 100 5% 1/10W
R371 1-216-049-91 RES,CHIP 1K 5% 1/10W R597 1-216-025-91 RES,CHIP 100 5% 1/10W
R372 1-216-049-91 RES,CHIP 1K 5% 1/10W R598 1-216-025-91 RES,CHIP 100 5% 1/10W

R381 1-216-025-91 RES,CHIP 100 5% 1/10W R705 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R382 1-216-025-91 RES,CHIP 100 5% 1/10W R729 1-216-045-00 METAL CHIP 680 5% 1/10W
R383 1-216-085-00 METAL CHIP 33K 5% 1/10W (GRX10AV:TH)
R384 1-216-085-00 METAL CHIP 33K 5% 1/10W R729 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R385 1-216-085-00 METAL CHIP 33K 5% 1/10W (GRX10AV:E2)
R729 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R401 1-216-073-00 METAL CHIP 10K 5% 1/10W (GRX10AV:AUS/RX110AV:AEP,UK,G)
R402 1-216-073-00 METAL CHIP 10K 5% 1/10W R729 1-216-085-00 METAL CHIP 33K 5% 1/10W
R403 1-216-073-00 METAL CHIP 10K 5% 1/10W (RX110AV:EE,CIS)
R404 1-216-073-00 METAL CHIP 10K 5% 1/10W
R411 1-216-073-00 METAL CHIP 10K 5% 1/10W R729 1-216-295-91 SHORT 0 (GRX10AV:E3,SP,MY,HK,EA)
R730 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R412 1-216-049-91 METAL CHIP 1K 5% 1/10W (RX110AV:AEP,UK,G)
R413 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R730 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R414 1-216-073-00 METAL CHIP 10K 5% 1/10W (GRX10AV:AUS)
R416 1-216-073-00 METAL CHIP 10K 5% 1/10W R730 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R417 1-216-073-00 METAL CHIP 10K 5% 1/10W (GRX10AV:E2/RX110AV:EE,CIS)
R730 1-216-077-00 METAL CHIP 15K 5% 1/10W
R418 1-216-073-00 METAL CHIP 10K 5% 1/10W (GRX10AV:TH)
R419 1-216-097-91 RES,CHIP 100K 5% 1/10W
R420 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R730 1-216-295-91 SHORT 0 (RX110AV:CND)
R506 1-216-025-91 RES,CHIP 100 5% 1/10W R731 1-216-073-00 METAL CHIP 10K 5% 1/10W
R508 1-216-025-91 RES,CHIP 100 5% 1/10W R769 1-216-073-00 METAL CHIP 10K 5% 1/10W
R770 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R513 1-216-109-00 METAL CHIP 330K 5% 1/10W R778 1-216-089-91 RES,CHIP 47K 5% 1/10W
R518 1-216-025-91 RES,CHIP 100 5% 1/10W
R521 1-216-025-91 RES,CHIP 100 5% 1/10W R779 1-216-089-91 RES,CHIP 47K 5% 1/10W
(RX110AV:AEP,UK,G) R780 1-216-089-91 RES,CHIP 47K 5% 1/10W
R522 1-216-025-91 RES,CHIP 100 5% 1/10W R781 1-216-089-91 RES,CHIP 47K 5% 1/10W
(RX110AV:AEP,UK,G) R800 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R526 1-216-025-91 RES,CHIP 100 5% 1/10W R901 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

R527 1-216-025-91 RES,CHIP 100 5% 1/10W R902 1-216-081-00 METAL CHIP 22K 5% 1/10W
R534 1-216-025-91 RES,CHIP 100 5% 1/10W R911 1-216-089-91 RES,CHIP 47K 5% 1/10W
R536 1-216-025-91 RES,CHIP 100 5% 1/10W R912 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R547 1-216-041-00 RES,CHIP 470 5% 1/10W R931 1-216-049-91 RES,CHIP 1K 5% 1/10W
R548 1-216-041-00 RES,CHIP 470 5% 1/10W R951 1-216-049-91 RES,CHIP 1K 5% 1/10W

R555 1-216-025-91 RES,CHIP 100 5% 1/10W R952 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R556 1-216-025-91 RES,CHIP 100 5% 1/10W R953 1-216-025-91 RES,CHIP 100 5% 1/10W
R557 1-216-025-91 RES,CHIP 100 5% 1/10W R954 1-216-089-91 RES,CHIP 47K 5% 1/10W
R558 1-216-041-00 RES,CHIP 470 5% 1/10W R955 1-216-089-91 RES,CHIP 47K 5% 1/10W
R560 1-216-025-91 RES,CHIP 100 5% 1/10W R956 1-216-073-00 METAL CHIP 10K 5% 1/10W

R561 1-216-025-91 RES,CHIP 100 5% 1/10W R961 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R563 1-216-025-91 RES,CHIP 100 5% 1/10W R962 1-216-079-00 METAL CHIP 18K 5% 1/10W
R564 1-216-025-91 RES,CHIP 100 5% 1/10W R963 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R565 1-216-025-91 RES,CHIP 100 5% 1/10W
R566 1-216-025-91 RES,CHIP 100 5% 1/10W < VARIABLE RESISTOR >

R567 1-216-025-91 RES,CHIP 100 5% 1/10W RV301 1-241-764-11 RES, ADJ, CARBON 10K
R568 1-216-025-91 RES,CHIP 100 5% 1/10W RV351 1-241-764-11 RES, ADJ, CARBON 10K
R572 1-216-041-00 RES,CHIP 470 5% 1/10W
R573 1-216-025-91 RES,CHIP 100 5% 1/10W < VIBRATOR >
R574 1-216-025-91 RES,CHIP 100 5% 1/10W
X201 1-579-125-11 VIBRATOR, CERAMIC (8MHz)
R575 1-216-025-91 RES,CHIP 100 5% 1/10W X501 1-579-233-11 VIBRATOR, CERAMIC (5MHz)
R576 1-216-025-91 RES,CHIP 100 5% 1/10W X502 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
R578 1-216-025-91 RES,CHIP 100 5% 1/10W
R579 1-216-025-91 RES,CHIP 100 5% 1/10W **************************************************************

– 117 –
Downloaded from www.Manualslib.com manuals search engine
 MIC MOTOR (TURN) MOTOR (SLIDE) PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-668-270-11 MIC BOARD < DIODE >
**********
D701 8-719-109-69 DIODE RD3.6ES-B2
< CAPACITOR >
< IC >
C752 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C754 1-164-232-11 CERAMIC CHIP 0.01uF 50V IC701 8-759-633-65 IC M54641L
C755 1-126-961-11 ELECT 2.2uF 20% 50V
C756 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V < RESISTOR >
C757 1-163-243-11 CERAMIC CHIP 47PF 5% 50V
R706 1-249-411-11 CARBON 330 5% 1/4W
C758 1-126-964-11 ELECT 10uF 20% 50V R707 1-249-401-11 CARBON 47 5% 1/4W F
C759 1-126-957-11 ELECT 0.22uF 20% 50V
C760 1-163-243-11 CERAMIC CHIP 47PF 5% 50V ************************************************************
C761 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C762 1-126-961-11 ELECT 2.2uF 20% 50V * 1-658-578-11 MOTOR (SLIDE) BOARD
*******************
C764 1-126-964-11 ELECT 10uF 20% 50V
C782 1-163-005-11 CERAMIC CHIP 470PF 10% 50V < CAPACITOR >

< FILTER > C801 1-162-306-11 CERAMIC 0.01uF 20% 16V

C804 1-162-306-11 CERAMIC 0.01uF 20% 16V
FL751 1-233-289-21 FILTER, CHIP EMI C805 1-126-964-11 ELECT 10uF 20% 50V

< IC > < CONNECTOR >

IC750 8-759-636-55 IC M5218AFP * CN801 1-568-947-11 PIN, CONNECTOR 9P

< JACK > < DIODE >

J751 1-784-224-11 JACK (LARGE TYPE) (MIX MIC) D801 8-719-010-43 DIODE UZ-5.6BSC
D804 8-719-911-19 DIODE 1SS119
< RESISTOR > D805 8-719-911-19 DIODE 1SS119

R750 1-216-073-00 METAL CHIP 10K 5% 1/10W < IC >

R751 1-216-049-91 RES,CHIP 1K 5% 1/10W
R752 1-216-097-91 RES,CHIP 100K 5% 1/10W IC801 8-759-274-09 IC BA6286N
R753 1-216-049-91 RES,CHIP 1K 5% 1/10W
R754 1-216-081-00 METAL CHIP 22K 5% 1/10W < RESISTOR >

R755 1-216-073-00 METAL CHIP 10K 5% 1/10W R801 1-249-401-11 CARBON 47 5% 1/4W F
R756 1-216-103-00 METAL CHIP 180K 5% 1/10W
R757 1-216-025-91 RES,CHIP 100 5% 1/10W < SWITCH >

< VARIABLE RESISTOR > S801 1-762-527-11 SWITCH, ROTARY

RV750 1-225-587-11 RES, VAR 50K (MIC LEVEL) ************************************************************

<CONNECTOR> * A-4407-266-A PANEL BOARD, COMPLETE (RX110AV:AEP,UK,G)

*********************
* W751 1-690-880-31 LEAD (WITH CONNECTOR)
* A-4407-312-A PANEL BOARD, COMPLETE
************************************************************** *********************
(GRX10AV/RX110AV:CND,EE,CIS)
* 1-658-577-11 MOTOR (TURN) BOARD
******************* * 4-932-810-31 CUSHION (FL)
* 4-996-796-01 HOLDER, FL TUBE
< CAPACITOR >
< CAPACITOR >
C701 1-162-306-11 CERAMIC 0.01uF 20% 16V
C702 1-126-964-11 ELECT 10uF 20% 50V C600 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C705 1-162-306-11 CERAMIC 0.01uF 20% 16V C601 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C602 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< CONNECTOR > C603 1-124-589-11 ELECT 47uF 20% 16V
C604 1-126-163-11 ELECT 4.7uF 20% 50V
CN703 1-750-413-11 CONNECTOR, FFC/FPC 8P
CN704 1-506-469-11 PIN, CONNECTOR 4P C605 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C606 1-126-160-11 ELECT 1uF 20% 50V

– 118 –
Downloaded from www.Manualslib.com manuals search engine
 PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C607 1-126-160-11 ELECT 1uF 20% 50V D806 8-719-988-62 DIODE 1SS355
C608 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V D807 8-719-988-62 DIODE 1SS355
C609 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< FILTER >
C610 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C611 1-163-251-11 CERAMIC CHIP 100PF 5% 50V FL601 1-233-289-21 FILTER, CHIP EMI
C612 1-163-251-11 CERAMIC CHIP 100PF 5% 50V FL602 1-233-289-21 FILTER, CHIP EMI
C613 1-163-251-11 CERAMIC CHIP 100PF 5% 50V FL801 1-233-289-21 FILTER, CHIP EMI
C614 1-163-251-11 CERAMIC CHIP 100PF 5% 50V FL802 1-233-289-21 FILTER, CHIP EMI
FL851 1-233-289-21 FILTER, CHIP EMI
C615 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C616 1-163-251-11 CERAMIC CHIP 100PF 5% 50V < IC >
C617 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C618 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC601 8-759-496-12 IC TMP87CM74AF-6671
C619 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC602 8-759-332-18 IC GP1U27XB
IC603 8-759-495-25 IC BA3833FP
C620 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC801 8-759-496-11 IC TMP87CH48DF-4825
C621 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC851 8-759-498-98 IC MSM6653A-GS-K
C625 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C626 1-124-589-11 ELECT 47uF 20% 16V < JUMPER RESISTOR >
C631 1-126-157-11 ELECT 10uF 20% 16V
JR903 1-216-296-91 SHORT 0
C632 1-126-157-11 ELECT 10uF 20% 16V JR904 1-216-296-91 SHORT 0
C633 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V JR905 1-216-296-91 SHORT 0
C634 1-126-157-11 ELECT 10uF 20% 16V JR906 1-216-295-91 SHORT 0
C652 1-164-232-11 CERAMIC CHIP 0.01uF 50V JR907 1-216-296-91 SHORT 0
C801 1-163-038-91 CERAMIC CHIP 0.1uF 25V
JR908 1-216-296-91 SHORT 0
C802 1-163-038-91 CERAMIC CHIP 0.1uF 25V JR909 1-216-296-91 SHORT 0
C803 1-124-589-11 ELECT 47uF 20% 16V JR911 1-216-296-91 SHORT 0
C804 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V JR912 1-216-295-91 SHORT 0
C805 1-163-038-91 CERAMIC CHIP 0.1uF 25V JR914 1-216-296-91 SHORT 0
C806 1-126-963-11 ELECT 4.7uF 20% 50V
JR915 1-216-296-91 SHORT 0
C807 1-163-017-00 CERAMIC CHIP 4700PF 10% 50V JR916 1-216-296-91 SHORT 0
C808 1-163-017-00 CERAMIC CHIP 4700PF 10% 50V JR917 1-216-296-91 SHORT 0
C809 1-126-967-11 ELECT 47uF 20% 50V JR919 1-216-295-91 SHORT 0
C851 1-163-038-91 CERAMIC CHIP 0.1uF 25V JR920 1-216-295-91 SHORT 0
C852 1-126-935-11 ELECT 470uF 20% 6.3V
JR921 1-216-295-91 SHORT 0
C853 1-126-963-11 ELECT 4.7uF 20% 50V JR922 1-216-295-91 SHORT 0
JR923 1-216-296-91 SHORT 0
< CONNECTOR > JR924 1-216-296-91 SHORT 0
JR925 1-216-295-91 SHORT 0
* CN601 1-568-832-11 SOCKET, CONNECTOR 13P
CN602 1-764-698-11 SOCKET, CONNECTOR 19P JR926 1-216-295-91 SHORT 0
* CN603 1-568-943-11 PIN, CONNECTOR 5P JR927 1-216-295-91 SHORT 0
CN604 1-506-486-11 PIN, CONNECTOR 7P JR928 1-216-295-91 SHORT 0

< DIODE > < COIL >

D601 8-719-058-24 DIODE RB501V-40TE-17 L601 1-412-031-11 INDUCTOR CHIP 47uH

D602 8-719-210-33 DIODE EC10DS2 L602 1-412-031-11 INDUCTOR CHIP 47uH
D603 8-719-210-33 DIODE EC10DS2 L851 1-412-031-11 INDUCTOR CHIP 47uH
D620 8-719-063-93 DIODE SLR325VC-N-T32 (EFFECT)
D621 8-719-056-13 DIODE SML79423C-TP15 (CD ^) < FLUORECENT INDICATOR >

D622 8-719-058-03 DIODE SEL5423E-TP15 (9 TAPE B) ND601 1-517-731-21 INDICATOR TUBE, FLUORESCENT
D623 8-719-058-03 DIODE SEL5423E-TP15 (( TAPE B)
D624 8-719-058-03 DIODE SEL5423E-TP15 (9 TAPE A) < TRANSISTOR >
D625 8-719-058-03 DIODE SEL5423E-TP15 (( TAPE A)
D629 8-719-057-97 DIODE SEL5923A-TP15 (DSP) Q601 8-729-118-00 TRANSISTOR 2SB1116-L
Q602 8-729-118-00 TRANSISTOR 2SB1116-L
D630 8-719-057-97 DIODE SEL5923A-TP15 (PRO LOGIC) Q603 8-729-120-28 TRANSISTOR 2SC1623-L5L6
D651 8-719-063-93 DIODE SLR325VC-N-T32 (r REC) Q607 8-729-027-60 TRANSISTOR DTC144TKA-T146
D652 8-719-057-97 DIODE SEL5923A-TP15 (P PAUSE) Q608 8-729-027-60 TRANSISTOR DTC144TKA-T146
D804 8-719-988-62 DIODE 1SS355
D805 8-719-988-62 DIODE 1SS355 Q609 8-729-027-60 TRANSISTOR DTC144TKA-T146

– 119 –
Downloaded from www.Manualslib.com manuals search engine
 PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q610 8-729-027-60 TRANSISTOR DTC144TKA-T146 R673 1-216-037-00 METAL CHIP 330 5% 1/10W
Q618 8-729-027-60 TRANSISTOR DTC144TKA-T146
Q701 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R674 1-216-027-00 METAL CHIP 120 5% 1/10W
Q702 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R675 1-216-027-00 METAL CHIP 120 5% 1/10W
R676 1-216-027-00 METAL CHIP 120 5% 1/10W
Q851 8-729-027-23 TRANSISTOR DTA114EKA-T146 R677 1-216-027-00 METAL CHIP 120 5% 1/10W
Q958 1-801-806-11 TRANSISTOR DTC114EKA-T146 R678 1-216-027-00 METAL CHIP 120 5% 1/10W
Q959 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q960 8-729-027-23 TRANSISTOR DTA114EKA-T146 R679 1-216-027-00 METAL CHIP 120 5% 1/10W
R683 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
< RESISTOR > R684 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R701 1-216-073-00 METAL CHIP 10K 5% 1/10W
R601 1-216-121-91 RES,CHIP 1M 5% 1/10W R702 1-216-073-00 METAL CHIP 10K 5% 1/10W
R602 1-216-025-91 RES,CHIP 100 5% 1/10W
R604 1-216-073-00 METAL CHIP 10K 5% 1/10W R703 1-216-097-91 RES,CHIP 100K 5% 1/10W
R605 1-216-073-00 METAL CHIP 10K 5% 1/10W R704 1-216-097-91 RES,CHIP 100K 5% 1/10W
R606 1-216-073-00 METAL CHIP 10K 5% 1/10W R720 1-216-029-00 METAL CHIP 150 5% 1/10W
(GRX10AV:E2,E3,EA,SP,MY,HK,AUS/RX110AV)
R607 1-216-073-00 METAL CHIP 10K 5% 1/10W R721 1-216-029-00 METAL CHIP 150 5% 1/10W
R608 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R723 1-216-075-00 METAL CHIP 12K 5% 1/10W
R609 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R610 1-216-025-91 RES,CHIP 100 5% 1/10W R724 1-216-039-00 METAL CHIP 390 5% 1/10W
R611 1-216-025-91 RES,CHIP 100 5% 1/10W R725 1-216-041-00 METAL CHIP 470 5% 1/10W
R726 1-216-045-00 METAL CHIP 680 5% 1/10W
R612 1-216-017-91 RES,CHIP 47 5% 1/10W R727 1-216-047-00 METAL CHIP 820 5% 1/10W
R613 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R728 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
(GRX10AV:TH)
R613 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R729 1-216-053-91 RES,CHIP 1.5K 5% 1/10W
(GRX10AV:E2,E3,EA,SP,MY,HK,AUS/RX110AV) R730 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R614 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R731 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
(GRX10AV:E2,E3,EA,SP,MY,HK,AUS/RX110AV) R742 1-216-027-00 METAL CHIP 120 5% 1/10W
R614 1-216-073-00 METAL CHIP 10K 5% 1/10W R743 1-216-027-00 METAL CHIP 120 5% 1/10W
(GRX10AV:TH)
R801 1-216-121-91 RES,CHIP 1M 5% 1/10W
R616 1-216-097-91 RES,CHIP 100K 5% 1/10W R802 1-216-025-91 RES,CHIP 100 5% 1/10W
R618 1-216-089-91 RES,CHIP 47K 5% 1/10W R803 1-216-025-91 RES,CHIP 100 5% 1/10W
R619 1-216-089-91 RES,CHIP 47K 5% 1/10W R804 1-216-025-91 RES,CHIP 100 5% 1/10W
R621 1-216-075-00 METAL CHIP 12K 5% 1/10W R805 1-216-075-00 METAL CHIP 12K 5% 1/10W
R622 1-216-039-00 METAL CHIP 390 5% 1/10W
R806 1-216-075-00 METAL CHIP 12K 5% 1/10W
R623 1-216-041-00 METAL CHIP 470 5% 1/10W R807 1-216-085-00 METAL CHIP 33K 5% 1/10W
R624 1-216-045-00 METAL CHIP 680 5% 1/10W R808 1-216-113-00 METAL CHIP 470K 5% 1/10W
R625 1-216-047-00 METAL CHIP 820 5% 1/10W R809 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R626 1-216-051-00 METAL CHIP 1.2K 5% 1/10W R810 1-216-089-91 RES,CHIP 47K 5% 1/10W
R627 1-216-053-91 RES,CHIP 1.5K 5% 1/10W
R851 1-216-097-91 RES,CHIP 100K 5% 1/10W
R628 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R852 1-216-025-91 RES,CHIP 100 5% 1/10W
R629 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R954 1-216-097-91 RES,CHIP 100K 5% 1/10W
R630 1-216-063-91 METAL CHIP 3.9K 5% 1/10W
R631 1-216-067-00 METAL CHIP 5.6K 5% 1/10W R955 1-216-097-91 RES,CHIP 100K 5% 1/10W
R632 1-216-071-91 RES,CHIP 8.2K 5% 1/10W
< SWITCH >
R633 1-216-075-00 METAL CHIP 12K 5% 1/10W
R636 1-216-075-00 METAL CHIP 12K 5% 1/10W S604 1-762-875-21 SWITCH, KEYBOARD (PRO LOGIC)
R649 1-216-075-00 METAL CHIP 12K 5% 1/10W S605 1-762-875-21 SWITCH, KEYBOARD (DSP)
R650 1-216-039-00 METAL CHIP 390 5% 1/10W S606 1-762-875-21 SWITCH, KEYBOARD (KARAOKE PON/MPX)
R651 1-216-041-00 METAL CHIP 470 5% 1/10W S607 1-762-875-21 SWITCH, KEYBOARD (p)
S608 1-762-875-21 SWITCH, KEYBOARD (P FILE MEMORY)
R652 1-216-045-00 METAL CHIP 680 5% 1/10W
R653 1-216-047-00 METAL CHIP 820 5% 1/10W S609 1-762-875-21 SWITCH, KEYBOARD (GEQ CONTROL)
R654 1-216-051-00 METAL CHIP 1.2K 5% 1/10W S610 1-762-875-21 SWITCH, KEYBOARD (FILE SELECT)
R655 1-216-053-91 RES,CHIP 1.5K 5% 1/10W S611 1-762-875-21 SWITCH, KEYBOARD (EFFECT)
R661 1-216-089-91 RES,CHIP 47K 5% 1/10W S612 1-762-875-21 SWITCH, KEYBOARD (DEMO)
S613 1-762-875-21 SWITCH, KEYBOARD (TIMER SELECT)
R662 1-216-089-91 RES,CHIP 47K 5% 1/10W
R663 1-216-049-91 RES,CHIP 1K 5% 1/10W S614 1-762-875-21 SWITCH, KEYBOARD (FUNCTION)
R664 1-216-049-91 RES,CHIP 1K 5% 1/10W S615 1-762-875-21 SWITCH, KEYBOARD (CLOCK/TIMER SET)
R665 1-216-089-91 RES,CHIP 47K 5% 1/10W S616 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)

– 120 –
Downloaded from www.Manualslib.com manuals search engine
 PANEL POWER

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
S631 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND) C207 1-130-493-00 MYLAR 0.068uF 5% 50V
S632 1-762-875-21 SWITCH, KEYBOARD (CD ^) C208 1-130-493-00 MYLAR 0.068uF 5% 50V
C221 1-162-284-31 CERAMIC 150PF 10% 50V
S633 1-762-875-21 SWITCH, KEYBOARD (9 TAPE B) C222 1-162-284-31 CERAMIC 150PF 10% 50V
S634 1-762-875-21 SWITCH, KEYBOARD (( TAPE B)
S635 1-762-875-21 SWITCH, KEYBOARD (9 TAPE A) C223 1-164-159-21 CERAMIC 0.1uF 50V
S636 1-762-875-21 SWITCH, KEYBOARD (( TAPE A) C224 1-128-560-11 ELECT 22uF 20% 100V
S652 1-762-875-21 SWITCH, KEYBOARD C225 1-161-494-00 CERAMIC 0.022uF 25V
(PLAY MODE, DOLBY NR, TUNER MEMORY) (RX110AV:AEP,UK,G,EE,CIS)
C228 1-162-284-31 CERAMIC 150PF 10% 50V
S653 1-762-875-21 SWITCH, KEYBOARD (EDIT, DIRECTION) C251 1-128-582-11 ELECT 10uF 20% 100V
S654 1-762-875-21 SWITCH, KEYBOARD (REPEAT, STEREO/MONO)
S655 1-762-875-21 SWITCH, KEYBOARD (PTY) (RX110AV:AEP,UK,G) C252 1-162-292-31 CERAMIC 680PF 10% 50V
S656 1-762-875-21 SWITCH, KEYBOARD (r REC) C253 1-162-286-21 CERAMIC 220PF 10% 50V
S657 1-762-875-21 SWITCH, KEYBOARD (P PAUSE) C254 1-126-967-11 ELECT 47uF 20% 50V
C255 1-126-967-11 ELECT 47uF 20% 50V
S658 1-762-875-21 SWITCH, KEYBOARD (HI-DUB) C256 1-128-560-11 ELECT 22uF 20% 100V
S659 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)
C257 1-130-493-00 MYLAR 0.068uF 5% 50V
< VIBRATOR > C258 1-130-493-00 MYLAR 0.068uF 5% 50V
C301 1-126-934-11 ELECT 220uF 20% 10V
X501 1-579-125-11 VIBRATOR, CERAMIC (8MHz) C302 1-126-934-11 ELECT 220uF 20% 10V
X601 1-579-125-11 VIBRATOR, CERAMIC (8MHz) C303 1-126-961-99 ELECT 2.2uF 20% 50V
X851 1-767-353-11 VIBRATOR, CERAMIC (4.09MHz)
C311 1-126-959-11 ELECT 0.47uF 20% 50V
************************************************************** C312 1-128-573-11 ELECT 470uF 20% 71V
C313 1-128-573-11 ELECT 470uF 20% 71V
* A-4407-272-A POWER BOARD, COMPLETE C331 1-126-924-11 ELECT 330uF 20% 10V
********************** C401 1-126-963-11 ELECT 4.7uF 20% 50V
(RX110AV:AEP,UK,G,EE,CIS)
C402 1-164-159-21 CERAMIC 0.1uF 50V
* A-4407-298-A POWER BOARD, COMPLETE (GRX10AV) (RX110AV:AEP,UK,G,EE,CIS)
********************** C403 1-164-159-21 CERAMIC 0.1uF 50V
(RX110AV:AEP,UK,G,EE,CIS)
* A-4407-320-A POWER BOARD, COMPLETE (RX110AV:CND) C404 1-164-159-21 CERAMIC 0.1uF 50V
********************** (RX110AV:AEP,UK,G,EE,CIS)
C405 1-164-159-21 CERAMIC 0.1uF 50V
< CAPACITOR > (RX110AV:AEP,UK,G,EE,CIS)
C406 1-164-159-21 CERAMIC 0.1uF 50V
C101 1-130-781-00 FILM 0.22uF 10% 100V (RX110AV:AEP,UK,G,EE,CIS)
C102 1-130-781-00 FILM 0.22uF 10% 100V
C103 1-164-159-21 CERAMIC 0.1uF 50V C407 1-164-159-21 CERAMIC 0.1uF 50V
C104 1-164-159-21 CERAMIC 0.1uF 50V (RX110AV:AEP,UK,G,EE,CIS)
C105 1-126-943-11 ELECT 2200uF 20% 25V C410 1-164-159-21 CERAMIC 0.1uF 50V
(RX110AV:AEP,UK,G,EE,CIS)
C106 1-162-294-31 CERAMIC 0.001uF 10% 50V C411 1-164-159-21 CERAMIC 0.1uF 50V
C107 1-162-294-31 CERAMIC 0.001uF 10% 50V (RX110AV:AEP,UK,G,EE,CIS)
C111 1-126-968-11 ELECT 100uF 20% 50V C412 1-161-494-00 CERAMIC 0.022uF 25V
C112 1-126-968-11 ELECT 100uF 20% 50V C413 1-161-494-00 CERAMIC 0.022uF 25V
C113 1-162-294-31 CERAMIC 0.001uF 10% 50V
C414 1-161-494-00 CERAMIC 0.022uF 25V
C114 1-126-967-11 ELECT 47uF 20% 50V C415 1-161-494-00 CERAMIC 0.022uF 25V
C151 1-128-493-11 ELECT 4700uF 20% 71V
(GRX10AV) < CONNECTOR >
C151 1-104-482-11 ELECT 4700uF 20% 63V
(RX110AV) CN201 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P
C152 1-128-493-11 ELECT 4700uF 20% 71V CN202 1-770-724-11 CONNECTOR, BOARD TO BOARD 9P
(GRX10AV) * CN203 1-573-128-11 PIN, CONNECTOR 5P
C152 1-104-482-11 ELECT 4700uF 20% 63V
(RX110AV) < DIODE >

C201 1-128-582-11 ELECT 10uF 20% 100V D101 8-719-510-68 DIODE D5SBA20F01
C202 1-162-292-31 CERAMIC 680PF 10% 50V D102 8-719-028-23 DIODE D3SBA20-4101
C203 1-162-286-21 CERAMIC 220PF 10% 50V D103 8-719-200-82 DIODE 11ES2
C204 1-126-967-11 ELECT 47uF 20% 50V D104 8-719-200-82 DIODE 11ES2
C205 1-126-967-11 ELECT 47uF 20% 50V D105 8-719-991-33 DIODE 1SS133T-77 (RX110AV:AEP,UK,G,EE,CIS)

C206 1-128-560-11 ELECT 22uF 20% 100V D111 8-719-200-82 DIODE 11ES2

– 121 –
Downloaded from www.Manualslib.com manuals search engine
 POWER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D112 8-719-200-82 DIODE 11ES2 R103 1-249-441-11 CARBON 100K 5% 1/4W
D113 8-719-002-60 DIODE UZL-33L ! R111 1-217-637-00 FUSIBLE 1 5% 1/4W F
D114 8-719-010-43 DIODE UZ-5.6BSC R112 1-249-417-11 CARBON 1K 5% 1/4W F
D201 8-719-991-33 DIODE 1SS133T-77
R113 1-249-417-11 CARBON 1K 5% 1/4W F
D251 8-719-991-33 DIODE 1SS133T-77 R114 1-247-815-91 CARBON 220 5% 1/4W
D301 8-719-991-33 DIODE 1SS133T-77 R115 1-247-815-91 CARBON 220 5% 1/4W
D311 8-719-991-33 DIODE 1SS133T-77 R116 1-249-425-11 CARBON 4.7K 5% 1/4W F
D321 8-719-991-33 DIODE 1SS133T-77 R201 1-249-417-11 CARBON 1K 5% 1/4W F
D331 8-719-991-33 DIODE 1SS133T-77
R202 1-249-437-11 CARBON 47K 5% 1/4W
D332 8-719-991-33 DIODE 1SS133T-77 R203 1-249-412-11 CARBON 390 5% 1/4W F
D401 8-719-991-33 DIODE 1SS133T-77 R204 1-249-437-11 CARBON 47K 5% 1/4W
D403 8-719-911-19 DIODE 1SS119 R205 1-260-107-11 CARBON 4.7K 5% 1/2W
D405 8-719-991-33 DIODE 1SS133T-77 R206 1-260-107-11 CARBON 4.7K 5% 1/2W
D406 8-719-991-33 DIODE 1SS133T-77
! R207 1-212-881-11 FUSIBLE 100 5% 1/4W F
D407 8-719-911-19 DIODE 1SS119 R208 1-220-893-11 METAL 0.22 10% 5W
D408 8-719-911-19 DIODE 1SS119 R209 1-249-417-11 CARBON 1K 5% 1/4W F
R210 1-249-431-11 CARBON 15K 5% 1/4W
< GROUND PLATE > R211 1-249-441-11 CARBON 100K 5% 1/4W

* EP101 1-537-738-21 TERMINAL, EARTH R212 1-260-076-11 CARBON 10 5% 1/2W

* EP201 1-537-738-21 TERMINAL, EARTH ! R221 1-217-637-00 FUSIBLE 1 5% 1/4W F
R222 1-260-103-11 CARBON 2.2K 5% 1/2W
< IC > R223 1-260-103-11 CARBON 2.2K 5% 1/2W
R224 1-249-425-11 CARBON 4.7K 5% 1/4W F
IC201 8-749-921-68 IC STK-4231MK2 (GRX10AV)
IC201 8-749-922-65 IC STK-4221MK2 (RX110AV) R251 1-249-417-11 CARBON 1K 5% 1/4W F
R252 1-249-437-11 CARBON 47K 5% 1/4W
< COIL > R253 1-249-412-11 CARBON 390 5% 1/4W F
R254 1-249-437-11 CARBON 47K 5% 1/4W
L401 1-420-872-00 COIL, AIR-CORE (RX110AV:AEP,UK,G,EE,CIS) R255 1-260-107-11 CARBON 4.7K 5% 1/2W
L402 1-420-872-00 COIL, AIR-CORE (RX110AV:AEP,UK,G,EE,CIS)
L403 1-420-872-00 COIL, AIR-CORE (RX110AV:AEP,UK,G,EE,CIS) R256 1-260-107-11 CARBON 4.7K 5% 1/2W
L405 1-420-872-00 COIL, AIR-CORE (RX110AV:AEP,UK,G,EE,CIS) ! R257 1-212-881-11 FUSIBLE 100 5% 1/4W F
R258 1-220-893-11 METAL 0.22 10% 5W
< TRANSISTOR > R259 1-249-417-11 CARBON 1K 5% 1/4W F
R260 1-249-431-11 CARBON 15K 5% 1/4W
Q101 8-729-119-78 TRANSISTOR 2SC403SP-51
(RX110AV:AEP,UK,G,EE,CIS) R261 1-249-441-11 CARBON 100K 5% 1/4W
Q111 8-729-118-01 TRANSISTOR 2SB1116 R262 1-260-076-11 CARBON 10 5% 1/2W
Q201 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA R271 1-260-093-11 CARBON 330 5% 1/2W
Q251 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA R272 1-260-093-11 CARBON 330 5% 1/2W
Q301 8-729-119-76 TRANSISTOR 2SA1175-HFE R273 1-260-093-11 CARBON 330 5% 1/2W

Q302 8-729-119-78 TRANSISTOR 2SC403SP-51 R274 1-260-093-11 CARBON 330 5% 1/2W

Q303 8-729-900-36 TRANSISTOR DTC124ES R301 1-249-429-11 CARBON 10K 5% 1/4W
Q304 8-729-119-76 TRANSISTOR 2SA1175-HFE R302 1-249-425-11 CARBON 4.7K 5% 1/4W F
Q305 8-729-900-36 TRANSISTOR DTC124ES R303 1-249-429-11 CARBON 10K 5% 1/4W
Q306 8-729-119-78 TRANSISTOR 2SC403SP-51 R304 1-249-429-11 CARBON 10K 5% 1/4W

Q307 8-729-119-78 TRANSISTOR 2SC403SP-51 R305 1-249-425-11 CARBON 4.7K 5% 1/4W F

Q321 8-729-119-78 TRANSISTOR 2SC403SP-51 R306 1-249-441-11 CARBON 100K 5% 1/4W
Q322 8-729-900-36 TRANSISTOR DTC124ES R308 1-247-903-00 CARBON 1M 5% 1/4W
Q401 8-729-040-20 TRANSISTOR RT1P137L-TP R310 1-247-903-00 CARBON 1M 5% 1/4W
Q402 8-729-900-80 TRANSISTOR DTC114ES R311 1-249-441-11 CARBON 100K 5% 1/4W

Q404 8-729-040-20 TRANSISTOR RT1P137L-TP R312 1-249-419-11 CARBON 1.5K 5% 1/4W F

Q405 8-729-904-39 TRANSISTOR DTC114TS R313 1-247-863-91 CARBON 22K 5% 1/4W
Q406 8-729-900-80 TRANSISTOR DTC114ES R314 1-247-863-91 CARBON 22K 5% 1/4W
R315 1-249-439-11 CARBON 68K 5% 1/4W
< RESISTOR > R316 1-249-437-11 CARBON 47K 5% 1/4W

! R101 1-215-886-11 METAL OXIDE 100 5% 2W F R321 1-249-440-11 CARBON 82K 5% 1/4W
(RX110AV:AEP,UK,G,EE,CIS) R322 1-249-441-11 CARBON 100K 5% 1/4W
R102 1-249-429-11 CARBON 10K 5% 1/4W R323 1-249-441-11 CARBON 100K 5% 1/4W
(RX110AV:AEP,UK,G,EE,CIS) R324 1-249-441-11 CARBON 100K 5% 1/4W

The components identified by Les composants identifiés par une

mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.
– 122 –
Downloaded from www.Manualslib.com manuals search engine
 POWER SENSOR SURROUND
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R331 1-247-890-11 CARBON 300K 5% 1/4W * 1-658-576-11 SENSOR BOARD
*************
R332 1-249-429-11 CARBON 10K 5% 1/4W
R333 1-249-431-11 CARBON 15K 5% 1/4W < IC >
! R401 1-215-893-11 METAL OXIDE 1.5K 5% 2W F
(GRX10AV) IC702 8-749-924-18 IC PHOTO INTERRUPTER RPI-1391
! R401 1-216-457-00 METAL OXIDE 1.2K 5% 2W F IC703 8-749-924-30 IC PHOTO REFLECTOR GP2S28
(RX110AV)
! R403 1-215-893-11 METAL OXIDE 1.5K 5% 2W F < RESISTOR >
(GRX10AV)
R701 1-249-416-11 CARBON 820 5% 1/4W F
! R403 1-216-457-00 METAL OXIDE 1.2K 5% 2W F R702 1-249-407-11 CARBON 150 5% 1/4W F
(RX110AV)
R406 1-249-437-11 CARBON 47K 5% 1/4W ************************************************************
R407 1-249-437-11 CARBON 47K 5% 1/4W
R408 1-249-440-11 CARBON 82K 5% 1/4W * A-4407-269-A SURROUND BOARD, COMPLETE
R409 1-249-437-11 CARBON 47K 5% 1/4W *************************
(RX110AV:AEP,G,UK,EE,CIS)
R410 1-249-389-11 CARBON 4.7 5% 1/4W F
(RX110AV:AEP,UK,G,EE,CIS) * A-4407-319-A SURROUND BOARD, COMPLETE (RX110AV:CND)
R411 1-249-389-11 CARBON 4.7 5% 1/4W F **************************
(RX110AV:AEP,UK,G,EE,CIS)
R412 1-249-389-11 CARBON 4.7 5% 1/4W F * A-4414-862-A SURROUND BOARD, COMPLETE (GRX10AV)
(RX110AV:AEP,UK,G,EE,CIS) **************************
R413 1-249-389-11 CARBON 4.7 5% 1/4W F
(RX110AV:AEP,UK,G,EE,CIS) < CAPACITOR >
R414 1-260-076-11 CARBON 10 5% 1/2W
(RX110AV:AEP,UK,G,EE,CIS) C601 1-126-965-11 ELECT 22uF 20% 50V
C602 1-162-292-31 CERAMIC 680PF 10% 50V
R415 1-260-076-11 CARBON 10 5% 1/2W C603 1-162-286-21 CERAMIC 220PF 10% 50V
(RX110AV:AEP,UK,G,EE,CIS) C604 1-126-963-11 ELECT 4.7uF 20% 50V
R416 1-249-389-11 CARBON 4.7 5% 1/4W F C605 1-126-967-11 ELECT 47uF 20% 50V
(RX110AV:AEP,UK,G,EE,CIS)
R417 1-249-389-11 CARBON 4.7 5% 1/4W F C606 1-126-965-11 ELECT 22uF 20% 50V
(RX110AV:AEP,UK,G,EE,CIS) C607 1-130-493-00 MYLAR 0.068uF 5% 50V
R420 1-249-389-11 CARBON 4.7 5% 1/4W F C608 1-130-493-00 MYLAR 0.068uF 5% 50V
(RX110AV:AEP,UK,G,EE,CIS) C621 1-162-294-31 CERAMIC 0.001uF 10% 50V
R421 1-249-389-11 CARBON 4.7 5% 1/4W F C622 1-104-971-11 ELECT 470uF 20% 50V
(RX110AV:AEP,UK,G,EE,CIS)
C623 1-162-284-31 CERAMIC 150PF 10% 50V
R422 1-249-393-11 CARBON 10 5% 1/4W F C627 1-162-284-31 CERAMIC 150PF 10% 50V
(RX110AV:AEP,UK,G,EE,CIS) (RX110AV:AEP,UK,G,EE,CIS)
R424 1-260-076-11 CARBON 10 5% 1/2W C628 1-161-494-00 CERAMIC 0.022uF 25V
(RX110AV:AEP,UK,G,EE,CIS) (RX110AV:AEP,UK,G,EE,CIS)
R425 1-260-095-11 CARBON 470 5% 1/2W C651 1-126-965-11 ELECT 22uF 20% 50V
R426 1-260-095-11 CARBON 470 5% 1/2W C652 1-162-292-31 CERAMIC 680PF 10% 50V
R427 1-260-095-11 CARBON 470 5% 1/2W
C653 1-162-286-21 CERAMIC 220PF 10% 50V
R428 1-260-095-11 CARBON 470 5% 1/2W C654 1-126-963-11 ELECT 4.7uF 20% 50V
R429 1-249-437-11 CARBON 47K 5% 1/4W C655 1-126-967-11 ELECT 47uF 20% 50V
R430 1-249-437-11 CARBON 47K 5% 1/4W C657 1-130-493-00 MYLAR 0.068uF 5% 50V
C658 1-130-493-00 MYLAR 0.068uF 5% 50V
< RELAY >
< CONNECTOR >
RY101 1-755-195-11 RELAY (RX110AV:AEP,UK,G,EE,CIS)
RY401 1-755-141-11 RELAY CN601 1-691-765-11 PLUG(MICROCONNECTOR)3P
RY403 1-515-920-11 RELAY (24V) CN602 1-691-770-11 PLUG (MICRO CONNECTOR) 8P

< THERMISTOR > < DIODE >

THP321 1-807-796-11 THERMISTOR D602 8-719-934-13 DIODE HZS24-1L (RX110AV)

D602 8-719-934-17 DIODE HZS27-1L (GRX10AV)
< TERMINAL > D604 8-719-911-19 DIODE 1SS119

TM401 1-537-842-11 TERMINAL BOARD (FRONT SPEAKER) < EARTH TERMINAL >
TM402 1-537-510-11 TERMINAL BOARD (SPEAKER)(6P)
(SURROUND SPEAKER) * EP601 1-537-738-21 TERMINAL, EARTH (RX110AV:AEP,UK,G,EE,CIS)

**************************************************************
The components identified by Les composants identifiés par une
mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.
– 123 –
Downloaded from www.Manualslib.com manuals search engine
 SURROUND TCB
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* EP602 1-537-738-21 TERMINAL, EARTH (RX110AV:AEP,UK,G,EE,CIS) C21 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C22 1-163-031-11 CERAMIC CHIP 0.01uF 50V
< IC > C23 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C24 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
IC601 8-749-900-96 IC STK-4142MK2
C26 1-126-967-11 ELECT 47uF 20% 16V
< TRANSISTOR > C28 1-126-967-11 ELECT 47uF 20% 16V
C29 1-162-306-11 CERAMIC 0.01uF 30% 16V
Q601 8-729-119-76 TRANSISTOR 2SA1175-HFE C30 1-126-961-11 ELECT 2.2uF 20% 50V
Q604 8-729-119-78 TRANSISTOR 2SC403SP-51 C31 1-163-031-11 CERAMIC CHIP 0.01uF 50V
Q651 8-729-119-76 TRANSISTOR 2SA1175-HFE
C32 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< RESISTOR > C33 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C34 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
R601 1-249-417-11 CARBON 1K 5% 1/4W F C35 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R602 1-249-437-11 CARBON 47K 5% 1/4W C36 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R603 1-249-413-11 CARBON 470 5% 1/4W F
R604 1-249-437-11 CARBON 47K 5% 1/4W C37 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R605 1-260-103-11 CARBON 2.2K 5% 1/2W C39 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C40 1-126-967-11 ELECT 47uF 20% 16V
R606 1-260-103-11 CARBON 2.2K 5% 1/2W C41 1-163-031-11 CERAMIC CHIP 0.01uF 50V
! R607 1-212-881-11 FUSIBLE 100 5% 1/4W F C42 1-163-038-91 CERAMIC CHIP 0.1uF 25V
! R608 1-217-151-00 METAL 0.22 10% 2W
R608 1-220-755-11 METAL 0.22 10% 2W C43 1-163-031-91 CERAMIC CHIP 0.01uF 50V
R609 1-249-441-11 CARBON 100K 5% 1/4W C44 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C45 1-163-077-00 CERAMIC CHIP 0.1uF 50V
R610 1-249-441-11 CARBON 100K 5% 1/4W C46 1-126-967-11 ELECT 47uF 20% 16V
R611 1-249-441-11 CARBON 100K 5% 1/4W C47 1-126-301-11 ELECT 1.0uF 20% 50V
R612 1-260-076-11 CARBON 10 5% 1/2W
R621 1-260-109-11 CARBON 6.8K 5% 1/2W F C48 1-163-059-00 CERAMIC CHIP 0.01uF 50V
! R622 1-217-881-11 FUSIBLE 100 5% 1/4W F C49 1-126-964-11 ELECT 10uF 20% 50V
C50 1-126-960-11 ELECT 1.0uF 20% 50V
R629 1-249-429-11 CARBON 10K 5% 1/4W C51 1-126-959-11 ELECT 0.47uF 20% 50V
R651 1-249-417-11 CARBON 1K 5% 1/4W F C52 1-126-960-11 ELECT 1.0uF 20% 50V
R652 1-249-437-11 CARBON 47K 5% 1/4W
R653 1-249-415-11 CARBON 680 5% 1/4W F C53 1-126-964-11 ELECT 10uF 20% 50V
R654 1-249-437-11 CARBON 47K 5% 1/4W C54 1-104-396-11 ELECT 10uF 20% 16V
C55 1-104-396-11 ELECT 10uF 20% 16V
R655 1-260-103-11 CARBON 2.2K 5% 1/2W C56 1-104-396-11 ELECT 10uF 20% 16V
R656 1-260-103-11 CARBON 2.2K 5% 1/2W C57 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
R658 1-217-151-00 METAL 0.22 10% 2W
! R658 1-220-755-11 METAL 0.22 10% 2W C58 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
R659 1-249-441-11 CARBON 100K 5% 1/4W C59 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C60 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
R660 1-249-441-11 CARBON 100K 5% 1/4W C61 1-126-301-11 ELECT 1.0uF 20% 50V
R661 1-249-441-11 CARBON 100K 5% 1/4W C62 1-163-031-11 CERAMIC CHIP 0.01uF 50V
R662 1-260-076-11 CARBON 10 5% 1/2W
C63 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
************************************************************** C64 1-126-967-11 ELECT 47uF 20% 16V
C65 1-126-967-11 ELECT 47uF 20% 16V
* A-4303-588-A TCB BOARD, COMPLETE (EE,CIS) C66 1-163-031-11 CERAMIC CHIP 0.01uF 50V
*************************** C67 1-126-162-11 ELECT 3.3uF 20% 50V

< CAPACITOR > C68 1-163-031-11 CERAMIC 0.01uF 50V

C69 1-126-967-11 ELECT 47uF 20% 16V
C1 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V C71 1-162-306-11 CERAMIC 0.01uF 30% 16V
C2 1-126-967-11 ELECT 47uF 20% 16V C72 1-126-967-11 ELECT 47uF 20% 16V
C3 1-163-038-91 CERAMIC CHIP 0.1uF 25V C73 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C5 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C6 1-163-038-91 CERAMIC CHIP 0.1uF 25V C74 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C1701 1-162-294-31 CERAMIC CHIP 0.001uF 10% 50V
C7 1-101-004-00 CERAMIC 0.01uF 50V C1702 1-130-014-00 FILM 470PF 5% 50V
C8 1-163-031-11 CERAMIC CHIP 0.01uF 50V C1703 1-126-959-11 ELECT 0.47uF 20% 50V
C9 1-163-031-11 CERAMIC CHIP 0.01uF 50V C1704 1-126-959-11 ELECT 0.47uF 20% 50V
C10 1-162-306-11 CERAMIC CHIP 0.01uF 30% 16V
C16 1-163-038-91 CERAMIC CHIP 0.1uF 25V C1705 1-163-035-00 CERAMIC CHIP 0.047uF 50V
C1706 1-126-960-11 ELECT 1.0uF 20% 50V
C19 1-163-249-11 CERAMIC CHIP 82PF 5% 50V C1707 1-163-129-00 CERAMIC CHIP 330PF 5% 50V

The components identified by Les composants identifiés par une

mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.
– 124 –
Downloaded from www.Manualslib.com manuals search engine
 TCB

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C1710 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V JR46 1-216-296-91 METAL CHIP 0 5% 1/8W
C1711 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V JR47 1-216-295-91 METAL CHIP 0 5% 1/10W
JR48 1-216-295-91 METAL CHIP 0 5% 1/10W
C1712 1-130-736-11 FILM 0.01uF 5% 50V JR49 1-216-296-91 METAL CHIP 0 5% 1/8W
C1713 1-130-736-11 FILM 0.01uF 5% 50V JR51 1-216-295-91 METAL CHIP 0 5% 1/10W
C1714 1-126-960-11 ELECT 1.0uF 20% 50V
C1715 1-126-960-11 ELECT 1.0uF 20% 50V JR52 1-216-295-91 METAL CHIP 0 5% 1/10W
C1716 1-126-960-11 ELECT 1.0uF 20% 50V JR53 1-216-296-91 METAL CHIP 0 5% 1/8W
JR54 1-216-295-91 METAL CHIP 0 5% 1/10W
C1719 1-126-967-11 ELECT 47uF 20% 16V JR1701 1-216-295-91 METAL CHIP 0 5% 1/10W
C1720 1-163-031-11 CERAMIC CHIP 0.01uF 50V JR1702 1-216-295-91 METAL CHIP 0 5% 1/10W
C1723 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C1724 1-163-031-11 CERAMIC CHIP 0.01uF 50V JR1703 1-216-295-91 METAL CHIP 0 5% 1/10W
C1725 1-126-967-11 ELECT 47uF 20% 16V JR1704 1-216-295-91 METAL CHIP 0 5% 1/10W
JR1705 1-216-295-91 METAL CHIP 0 5% 1/10W
C1726 1-126-960-11 ELECT 1.0uF 20% 50V
C1727 1-126-960-11 ELECT 1.0uF 20% 50V < COIL >
C1728 1-126-966-11 ELECT 33uF 20% 16V
L3 1-410-521-11 MICRO INDUCTOR 100uH
< FILTER > L41 1-407-500-00 MICRO INDUCTOR 4.7mH
L1701 1-409-497-11 COIL (FILTER)
CF1 1-567-389-11 FILTER, CERAMIC
CF3 1-567-389-11 FILTER, CERAMIC < FILTER >

< CONNECTOR > LPF41 1-239-845-11 FILTER, LOW PASS

LPF42 1-239-845-11 FILTER, LOW PASS
* CN1 1-568-834-11 SOCKET, CONNECTOR 15P
< TRANSISTOR >
< TRIMMER >
Q1 8-729-201-27 TRANSISTOR 2SC2715Y
CT1701 1-141-444-11 CAP, CERAMIC TRIMMER 50PF Q2 8-729-201-27 TRANSISTOR 2SC2715Y
CT1701 1-141-569-11 CAP, ADJ 50PF Q3 8-729-201-27 TRANSISTOR 2SC2715Y
Q4 8-729-201-27 TRANSISTOR 2SC2715Y
< DIODE > Q5 8-729-216-22 TRANSISTOR MUN2111

D21 8-719-976-99 DIODE DTZ5.1B Q9 8-729-216-22 TRANSISTOR 2SA812-M5M6

D41 8-719-016-74 DIODE 1SS352 Q11 8-729-421-22 TRANSISTOR MUN2211
D42 8-719-016-74 DIODE 1SS352 Q12 8-729-421-22 TRANSISTOR MUN2211
D43 8-719-016-74 DIODE 1SS352 Q13 8-729-421-22 TRANSISTOR MUN2211
D1701 8-719-016-74 DIODE 1SS352 Q14 8-729-421-22 TRANSISTOR MUN2211

D1702 8-719-016-74 DIODE 1SS352 Q1701 8-729-424-08 TRANSISTOR MUN2111

D1703 8-719-991-33 DIODE 1SS133T Q1702 8-729-027-43 TRANSISTOR RT1N141C
D1704 8-719-016-74 DIODE 1SS352 Q1703 8-729-421-22 TRANSISTOR MUN2211

< FRONTEND > < RESISTOR >

FE1 1-693-335-11 FRONT END (3 GANG) R1 1-249-401-11 CARBON 47 5% 1/4W F

FE2 1-233-514-11 ENCAPSULATED COMPONENT R2 1-216-037-00 METAL CHIP 330 5% 1/10W
R3 1-216-037-00 METAL CHIP 330 5% 1/10W
< IC > R5 1-216-037-00 METAL CHIP 330 5% 1/10W
R6 1-216-081-00 METAL CHIP 22K 5% 1/10W
IC21 8-759-288-54 IC LC72130
IC41 8-759-495-82 IC LA1838 R7 1-216-037-00 METAL CHIP 330 5% 1/10W
IC1701 8-759-063-04 IC IR3R42 R8 1-216-037-00 METAL CHIP 330 5% 1/10W
IC1702 8-759-140-53 IC uPD4053BC R9 1-216-081-00 METAL CHIP 22K 5% 1/10W
R10 1-216-037-00 METAL CHIP 330 5% 1/10W
< IFT > R11 1-216-081-00 METAL CHIP 22K 5% 1/10W

IFT41 1-409-636-11 TRANSFORMER, IF (CERAMIC FILTER) R12 1-216-037-00 METAL CHIP 330 5% 1/10W
R13 1-216-037-00 METAL CHIP 330 5% 1/10W
< JUMPER RESISTOR > R14 1-216-081-00 METAL CHIP 22K 5% 1/10W
R18 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR2 1-216-295-91 METAL CHIP 0 5% 1/10W R19 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR6 1-216-295-91 METAL CHIP 0 5% 1/10W
JR8 1-216-295-91 METAL CHIP 0 5% 1/10W R21 1-249-417-11 CARBON 1.0K 5% 1/4W
JR9 1-216-295-91 METAL CHIP 0 5% 1/10W R22 1-249-417-11 CARBON 1.0K 5% 1/4W
JR12 1-216-296-91 METAL CHIP 0 5% 1/8W R23 1-249-417-11 CARBON 1.0K 5% 1/4W

– 125 –
Downloaded from www.Manualslib.com manuals search engine
 TCB

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R24 1-247-807-31 CARBON 100 5% 1/4W < VARIABLE RESISTOR >
R25 1-249-417-11 CARBON 1.0K 5% 1/4W F
RV41 1-238-600-11 RES, ADJ, CARBON 10K
R26 1-249-437-11 CARBON 47K 5% 1/4W RV42 1-238-600-11 RES, ADJ, CARBON 10K
R27 1-249-429-11 CARBON 10K 5% 1/4W RV1701 1-238-600-11 RES, ADJ, CARBON 10K
R28 1-249-417-11 CARBON 1.0K 5% 1/4W F RV1702 1-238-599-11 RES, ADJ, CARBON 4.7K
R29 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R30 1-216-186-00 METAL CHIP 330 5% 1/8W < TERMINAL >

R31 1-216-025-91 METAL CHIP 100 5% 1/10W TM1 1-537-488-11 TERMINAL BOARD (ANT) (ANTENNA)
R32 1-249-425-11 CARBON 4.7K 5% 1/4W F
R33 1-249-425-11 CARBON 4.7K 5% 1/4W F < TEST PIN>
R34 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R35 1-216-214-00 METAL CHIP 4.7K 5% 1/8W TP1701 1-536-354-00 PIN, POST
TP1702 1-536-354-00 PIN, POST
R36 1-216-025-91 METAL CHIP 100 5% 1/10W
R37 1-216-073-00 METAL CHIP 10K 5% 1/10W < VIBRATOR >
R38 1-216-089-91 METAL CHIP 47K 5% 1/10W
R39 1-249-429-11 CARBON 10K 5% 1/4W X21 1-760-549-31 VIBRATOR, CRYSTAL (4.5MHz)
R41 1-216-013-00 METAL CHIP 33 5% 1/10W X21 1-760-549-11 VIBRATOR, CRYSTAL (4.5MHz)
X41 1-767-825-21 FILTER, CERAMIC (10.7MHz)
R42 1-216-065-00 METAL CHIP 4.7K 5% 1/10W X42 1-527-981-00 FILTER, CERAMIC (450kHz)
R43 1-216-037-00 METAL CHIP 330 5% 1/10W
R44 1-216-001-00 METAL CHIP 10 5% 1/10W **************************************************************
R45 1-247-843-11 CARBON 3.3K 5% 1/4W F
R46 1-216-065-00 METAL CHIP 4.7K 5% 1/10W * A-4303-590-A TCB BOARD, COMPLETE (AEP,UK,G)
*****************************
R47 1-216-097-91 METAL CHIP 100K 5% 1/10W
R48 1-249-417-11 CARBON 1.0K 5% 1/4W F < CAPACITOR >
R49 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
R50 1-216-065-00 METAL CHIP 4.7K 5% 1/10W C1 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R51 1-216-065-00 METAL CHIP 4.7K 5% 1/10W C2 1-126-967-11 ELECT 47uF 20% 16V
C3 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R52 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C5 1-163-031-11 CERAMIC CHIP 0,01uF 50V
R53 1-216-061-00 METAL CHIP 3.3K 5% 1/4W C6 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R54 1-216-073-00 METAL CHIP 10K 5% 1/10W
R55 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C8 1-163-031-11 CERAMIC CHIP 0.01uF 50V
R57 1-216-162-00 METAL CHIP 33 5% 1/8W C9 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C10 1-163-031-11 CERAMIC CHIP 0.01uF 50V
R58 1-216-013-00 METAL CHIP 33 5% 1/10W C16 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R91 1-216-295-91 METAL CHIP 0 5% 1/10W C19 1-163-249-11 CERAMIC CHIP 82PF 5% 50V
R92 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1701 1-216-081-00 METAL CHIP 22K 5% 1/10W C21 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R1702 1-216-085-00 METAL CHIP 33K 5% 1/10W C22 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C23 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R1703 1-216-069-00 METAL CHIP 6.8K 5% 1/10W C24 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
R1704 1-216-076-00 METAL CHIP 13K 5% 1/10W C26 1-126-967-11 ELECT 47uF 20% 16V
R1705 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
R1706 1-216-049-91 METAL CHIP 1.0K 5% 1/10W C28 1-126-967-11 ELECT 47uF 20% 16V
R1707 1-216-097-91 METAL CHIP 100K 5% 1/10W C29 1-162-306-11 CERAMIC 0.01uF 30% 16V
C30 1-126-961-11 ELECT 2.2uF 20% 50V
R1708 1-216-095-00 METAL CHIP 82K 5% 1/10W C31 1-163-031-11 CERAMIC CHIP 0.01uF 50V
R1709 1-216-089-91 METAL CHIP 47K 5% 1/10W C32 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R1710 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1711 1-249-429-11 CARBON 10K 5% 1/4W C33 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R1714 1-216-067-00 METAL CHIP 5.6K 5% 1/10W C34 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C35 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R1715 1-216-067-00 METAL CHIP 5.6K 5% 1/10W C36 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R1716 1-216-097-91 METAL CHIP 100K 5% 1/10W C37 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R1717 1-216-097-91 METAL CHIP 100K 5% 1/10W
R1718 1-249-429-11 CARBON 10K 5% 1/4W C39 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
R1719 1-216-097-91 METAL CHIP 100K 5% 1/10W C40 1-126-967-11 ELECT 47uF 20% 16V
C41 1-163-031-11 CERAMIC CHIP 0.01uF 50V
R1720 1-249-434-11 CARBON 27K 5% 1/4W C42 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R1721 1-216-073-00 METAL CHIP 10K 5% 1/10W C43 1-163-031-11 CERAMIC CHIP 0.01uF 50V

C44 1-163-038-91 CERAMIC CHIP 0.1uF 25V

C45 1-163-077-00 CERAMIC CHIP 0.1uF 50V

– 126 –
Downloaded from www.Manualslib.com manuals search engine
 TCB

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C46 1-126-967-11 ELECT 47uF 20% 16V < FRONT-END >
C47 1-126-301-11 ELECT 1.0uF 20% 50V
C48 1-163-059-00 CERAMIC CHIP 0.01uF 50V FE1 1-693-357-11 FRONT END (4 GANG)
FE2 1-233-514-11 ENCAPSULATED COMPONENT
C49 1-126-964-11 ELECT 10uF 20% 50V
C50 1-126-960-11 ELECT 1.0uF 20% 50V < IC >
C51 1-126-959-11 ELECT 0.47uF 20% 50V
C52 1-126-960-11 ELECT 1.0uF 20% 50V IC21 8-759-288-54 IC LC72130
C53 1-126-964-11 ELECT 10uF 20% 50V IC41 8-759-495-82 IC LA1838
IC1751 8-759-634-51 IC M5218AP
C54 1-104-396-11 ELECT 10uF 20% 16V IC1752 8-759-450-86 IC BU1922
C55 1-104-396-11 ELECT 10uF 20% 16V
C56 1-104-396-11 ELECT 10uF 20% 16V < IFT >
C57 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
C58 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V IFT41 1-409-636-11 TRANSFORMER, IF (CERAMIC FILTER)

C59 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V < JUMPER RESISTOR >
C60 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
C61 1-126-301-11 ELECT 1uF 20% 50V JR2 1-216-295-91 METAL CHIP 0 5% 1/10W
C62 1-163-031-11 CERAMIC CHIP 0.01uF 50V JR6 1-216-295-91 METAL CHIP 0 5% 1/10W
C63 1-163-129-00 CERAMIC CHIP 330PF 5% 50V JR8 1-216-295-91 METAL CHIP 0 5% 1/10W
JR9 1-216-295-91 METAL CHIP 0 5% 1/10W
C65 1-126-967-11 ELECT 47uF 20% 16V JR12 1-216-296-91 METAL CHIP 0 5% 1/8W
C66 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C67 1-126-16211 ELECT 3.3uF 20% 50V JR46 1-216-296-91 METAL CHIP 0 5% 1/8W
C68 1-163-031-11 CERAMIC 0.01uF 50V JR47 1-216-295-11 METAL CHIP 0 5% 1/10W
C69 1-126-967-11 ELECT 47uF 20% 16V JR48 1-216-295-11 METAL CHIP 0 5% 1/10W
JR49 1-216-296-11 METAL CHIP 0 5% 1/8W
C71 1-162-306-11 CERAMIC 0.01uF 30% 16V JR51 1-216-295-11 METAL CHIP 0 5% 1/10W
C72 1-126-967-11 ELECT 47uF 20% 16V
C73 1-163-031-11 CERAMIC 0.01uF 50V JR52 1-216-295-11 METAL CHIP 0 5% 1/10W
C74 1-163-031-11 CERAMIC 0.01uF 50V JR53 1-216-296-11 METAL CHIP 0 5% 1/8W
C120 1-163-105-00 CERAMIC CHIP 33PF 5% 50V JR54 1-216-295-11 METAL CHIP 0 5% 1/10W

C1751 1-164-159-21 CERAMIC 0.1uF 50V < COIL >

C1752 1-126-967-11 ELECT 47uF 20% 16V
C1753 1-126-964-11 ELECT 10uF 20% 50V L2 1-414-142-11 MICRO INDUCTOR 1uH
C1754 1-162-291-31 CERAMIC 560PF 10% 50V L3 1-410-521-11 MICRO INDUCTOR 100uH
C1755 1-126-964-11 ELECT 10uF 20% 50V L4 1-410-515-11 INDUCTOR 33uH
L41 1-407-500-00 MICRO INDUCTOR 4.7mH
C1756 1-126-961-11 ELECT 2.2uF 20% 50V L1751 1-410-521-11 MICRO INDUCTOR 100uH
C1757 1-162-288-31 CERAMIC 330PF 10% 50V
C1758 1-163-031-11 CERAMIC CHIP 0.01uF 50V < FILTER >
C1759 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
C1760 1-163-031-11 CERAMIC CHIP 0.01uF 50V LPF41 1-239-845-11 FILTER, LOW PASS
LPF42 1-239-845-11 FILTER, LOW PASS
C1761 1-163-245-11 CERAMIC CHIP 56PF 5% 50V
C1762 1-163-245-11 CERAMIC CHIP 56PF 5% 50V < TRANSISTOR >
C1763 1-126-961-11 ELECT 2.2uF 20% 50V
Q1 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L
< FILTER > Q2 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L
Q3 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L
CF1 1-579-374-71 FILTER, CERAMIC Q4 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L
CF2 1-760-393-11 FILTER, CERAMIC Q5 8-729-424-08 TRANSISTOR MUN2111
CF3 1-760-393-11 FILTER, CERAMIC
Q9 8-729-216-22 TRANSISTOR 2SA812-M5M6
< CONNECTOR > Q11 8-729-421-22 TRANSISTOR MUN2211
Q12 8-729-421-22 TRANSISTOR MUN2211
* CN1 1-568-834-11 SOCKET, CONNECTOR 15P Q13 8-729-421-22 TRANSISTOR MUN2211
Q14 8-729-421-22 TRANSISTOR MUN2211
< DIODE >
< RESISTOR >
D21 8-719-976-99 DIODE UDZ-TE-17-5.1B
D41 8-719-016-74 DIODE 1SS352-TPH3 R1 1-249-401-11 CARBON 47 5% 1/4W F
D42 8-719-991-33 DIODE 1SS133T-77 R2 1-216-037-00 METAL CHIP 330 5% 1/10W
D1751 8-719-016-74 DIODE 1SS352-TPH3 R3 1-216-037-00 METAL CHIP 330 5% 1/10W
R5 1-216-037-00 METAL CHIP 330 5% 1/10W
R6 1-216-081-00 METAL CHIP 22K 5% 1/10W

– 127 –
Downloaded from www.Manualslib.com manuals search engine
 TCB TRANSFORMER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R7 1-216-037-00 METAL CHIP 330 5% 1/10W < VARIABLE RESISTOR >
R8 1-216-037-00 METAL CHIP 330 5% 1/10W
R9 1-216-081-00 METAL CHIP 22K 5% 1/10W RV41 1-238-600-11 RES, ADJ, CARBON 10K
R10 1-216-037-00 METAL CHIP 330 5% 1/10W RV42 1-238-600-11 RES, ADJ, CARBON 10K
R11 1-216-081-00 METAL CHIP 22K 5% 1/10W
< TERMINAL >
R12 1-216-037-00 METAL CHIP 330 5% 1/10W
R13 1-216-037-00 METAL CHIP 330 5% 1/10W TM1 1-537-488-11 TERMINAL BOARD (ANT) (ANTENNA)
R14 1-216-081-00 METAL CHIP 22K 5% 1/10W
R18 1-216-073-00 METAL CHIP 10K 5% 1/10W < VIBRATOR >
R19 1-216-073-00 METAL CHIP 10K 5% 1/10W
X21 1-760-549-11 VIBRATOR, CRYSTAL (4.5MHz)
R21 1-216-049-91 METAL CHIP 1.0K 5% 1/10W X41 1-767-825-21 FILTER, CERAMIC (10.7MHz)
R22 1-216-049-91 METAL CHIP 1.0K 5% 1/10W X42 1-527-981-00 FILTER, CERAMIC (450KHz)
R23 1-216-049-91 METAL CHIP 1.0K 5% 1/10W X1751 1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz)
R24 1-216-025-91 METAL CHIP 100 5% 1/10W
R25 1-249-417-11 CARBON 1K 5% 1/4W F ************************************************************

R26 1-249-437-11 CARBON 47K 5% 1/4W * 1-668-274-11 TRANSFORMER BOARD

R27 1-249-429-11 CARBON 10K 5% 1/4W *******************
R28 1-249-417-11 CARBON 1K 5% 1/4W F
R29 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < CONNECTOR >
R30 1-216-186-00 METAL CHIP 330 5% 1/8W
* CN501 1-564-527-11 PLUG, CONNECTOR 12P
R31 1-216-025-91 METAL CHIP 100 5% 1/10W CN502 1-774-108-11 PIN, CONNECTOR (PC BOARD) 2P
R32 1-249-425-11 CARBON 4.7K 5% 1/4W F
R33 1-249-425-11 CARBON 4.7K 5% 1/4W F < FUSE >
R34 1-249-425-11 CARBON 4.7K 5% 1/10W
R35 1-216-214-00 METAL CHIP 4.7K 5% 1/8W ! F501 1-532-505-31 FUSE T5AL/250V (GRX10AV:E2,E3,SP,MY,HK,EA)
! F504 1-532-506-31 FUSE T6.3A/250V (EXCEPT RX110AV:CND)
R36 1-216-025-91 METAL CHIP 100 5% 1/10W ! F504 1-533-310-11 FUSE, GLASS TUBE 6.3A/125V (RX110AV:CND)
R37 1-216-073-00 METAL CHIP 10K 5% 1/10W ! F505 1-532-506-31 FUSE T6.3A/250V (EXCEPT RX110AV:CND)
R38 1-216-089-91 METAL CHIP 47K 5% 1/10W ! F505 1-533-310-11 FUSE, GLASS TUBE 6.3A/125V (RX110AV:CND)
R39 1-249-429-11 CARBON 10K 5% 1/4W
R41 1-216-013-00 METAL CHIP 33 5% 1/10W < FUSE HOLDER >

R42 1-216-065-00 METAL CHIP 4.7K 5% 1/10W FH501 1-533-233-21 HOLDER, FUSE (GRX10AV:E2,E3,EA,SP,MY,HK)
R43 1-216-037-00 METAL CHIP 330 5% 1/10W FH502 1-533-233-21 HOLDER, FUSE (GRX10AV:E2,E3,EA,SP,MY,HK)
R44 1-216-001-00 METAL CHIP 10 5% 1/10W FH507 1-533-233-21 HOLDER, FUSE
R45 1-247-843-11 CARBON 3.3K 5% 1/4W F FH508 1-533-233-21 HOLDER, FUSE
R46 1-216-065-00 METAL CHIP 4.7K 5% 1/10W FH509 1-533-233-21 HOLDER, FUSE

R47 1-216-097-91 METAL CHIP 100K 5% 1/10W FH510 1-533-233-21 HOLDER, FUSE
R48 1-249-417-11 CARBON 1K 5% 1/4W F
R49 1-216-049-91 METAL CHIP 1.0K 5% 1/10W < RESISTOR >
R50 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R51 1-216-065-00 METAL CHIP 4.7K 5% 1/10W ! R501 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
! R502 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
R52 1-216-061-00 METAL CHIP 3.3K 5% 1/10W ! R503 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
R53 1-216-061-00 METAL CHIP 3.3K 5% 1/10W ! R504 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
R54 1-216-073-00 METAL CHIP 10K 5% 1/10W ! R505 1-202-725-00 SOLID 3.3M 10% 1/2W
R55 1-216-061-00 METAL CHIP 3.3K 5% 1/10W (RX110AV:CND)
R57 1-216-162-00 METAL CHIP 33 5% 1/8W
< SWITCH >
R58 1-216-013-00 METAL CHIP 33 5% 1/10W
R91 1-216-295-91 METAL CHIP 0 5% 1/10W ! S501 1-771-291-11 SELECTOR, VOLTAGE (VOLTAGE SELECTOR)
R92 1-216-073-00 METAL CHIP 10K 5% 1/10W (GRX10AV:E2,E3,EA,SP,MY,HK)
R1751 1-247-807-31 CARBON 100 5% 1/4W
R1752 1-216-073-00 METAL CHIP 10K 5% 1/10W < TRANSFORMER >

R1753 1-216-067-00 METAL CHIP 5.6K 5% 1/10W ! T501 1-431-709-11 TRANSFORMER, POWER
R1754 1-216-097-91 METAL CHIP 100K 5% 1/10W (GRX10AV:E2,EA,SP,MY,HK,AUS)
R1755 1-216-097-91 METAL CHIP 100K 5% 1/10W ! T501 1-431-710-11 TRANSFORMER, POWER
R1756 1-249-401-11 CARBON 47 5% 1/4W F (RX110AV:AEP,UK,G,EE,CIS)
R1757 1-216-295-91 METAL CHIP 0 5% 1/10W ! T501 1-431-711-21 TRANSFORMER, POWER (GRX10AV:TH)
! T501 1-431-712-11 TRANSFORMER, POWER (RX110AV:CND)
! T501 1-431-769-11 TRANSFORMER, POWER (GRX10AV:E3)

**************************************************************
The components identified by Les composants identifiés par une
mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
– 128 – specified. piéce portant le numéro spécifié.
Downloaded from www.Manualslib.com manuals search engine
 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MISCELLANEOUS #10 7-685-850-04 SCREW +BVTT 2X3 (S)
************** #11 7-628-254-15 SCREW +PS 2.6X6
#12 7-628-254-50 SCREW +PS 2.6X16
6 1-693-419-11 TUNER (FM/AM) (CND)
6 1-693-420-11 TUNER (FM/AM) (E2,TH,AUS)
6 1-693-421-11 TUNER (FM/AM) (E3,EA,SP,MY,HK)
8 1-769-977-11 WIRE (FLAT TYPE) (13 CORE)(150mm)
8 1-773-009-11 WIRE (FLAT TYPE) (15 CORE)(150mm)

54 1-773-041-11 WIRE (FLAT TYPE) (17 CORE)

! 58 1-569-007-11 ADAPTOR, CONVERSION 2P (E3)
! 58 1-569-008-11 ADAPTOR, CONVERSION 2P (EA,SP,MY)
! 58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK)
! 59 1-558-943-41 CORD, POWER (E2,E3)

! 59 1-575-042-21 CORD, POWER (CND)

! 59 1-575-651-21 CORD, POWER (AEP,G,UK,EE,CIS,EA,SP,MY,HK)
! 59 1-696-845-31 CORD, POWER (AUS)
! 59 1-751-326-21 CORD, POWER (TH)
60 1-773-011-11 WIRE (FLAT TYPE) (15 CORE)

61 1-773-112-11 WIRE (FLAT TYPE) (19 CORE)

121 1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
130 1-773-109-11 WIRE (FLAT TYPE) (19 CORE)(110mm)
257 1-452-879-11 MAGNET (CDM38L-5BD29AL)
257 1-452-925-21 MAGNET ASSY (CDM38LH-5BD29AL)

258 1-776-042-11 WIRE (FLAT TYPE) (8CORE)

HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR1)
HP101 A-2056-683-A DECK (A) ASSY, HEAD (230PWR1)
HRPE101 A-2056-682-A DECK (B) ASSY, HEAD (230AWR1)
HRPE101 A-2056-684-A DECK (B) ASSY, HEAD (230PWR1)

M1 A-2004-628-A MOTOR ASSY, CAPSTAN

M701 A-4672-004-A MOTOR ASSY (TURN)
M801 A-4672-004-A MOTOR ASSY (SLIDE)
M901 1-698-792-11 FAN, DC (RX110AV)
M901 1-763-048-21 FAN, D.C. (GRX10AV)

ND601 1-517-731-21 INDICATOR TUBE, FLUORESCENT

S811 1-473-335-11 ENCODER,ROTARY (BU,TRAY ADDRESS DET)
! T501 1-431-709-11 TRANSFORMER, POWER
(GRX10AV:E2,EA,SP,MY,HK,AUS)
! T501 1-431-710-11 TRANSFORMER, POWER
(RX110AV:AEP,G,UK,EE,CIS)
! T501 1-431-711-21 TRANSFORMER, POWER (GRX10AV:TH)

! T501 1-431-712-11 TRANSFORMER, POWER (RX110AV:CND)

! T501 1-431-769-11 TRANSFORMER, POWER (GRX10AV:E3)

************************************************************

**************
HARDWARE LIST
**************

#1 7-685-872-09 SCREW +BVTT 3X8 (S)

#2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
#4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
#5 7-685-871-01 SCREW +BVTT 3X6 (S)

#6 7-685-880-09 SCREW +BVTT 4X6 (S)(GRX10AV)

#6 7-685-871-01 SCREW +BVTT 3X6 (S)(RX110AV)
#7 7-685-851-04 SCREW +BVTT 2X4 (S)
#8 7-621-775-10 SCREW +B 2.6X4
#9 7-621-255-15 SCREW +P 2X3

The components identified by Les composants identifiés par une

mark ! or dotted line with mark marque ! sont critiques pour la
! are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
– 129 – specified. piéce portant le numéro spécifié.
Downloaded from www.Manualslib.com manuals search engine
 HCD-GRX10AV/RX110AV

Sony Corporation 98D0976-1

Printed in Japan © 1998. 4
9-922-783-11 Home A&V Products Company Published by General Engineering Dept.
– 130 – (Shibaura)
Downloaded from www.Manualslib.com manuals search engine