G5SBA20 and G5SBA60

Glass Passivated Single-Phase

Case Type GBU

rodu ct Bridge Rectifier

P Reverse Voltage 200 and 600 V
New
0.880 (22.3) 0.140 (3.56)

0.020 R (TYP.)
0.860 (21.8) 0.130 (3.30) Forward Current 6.0 A
0.125 (3.2) x 45o
9o
Features
CHAMFER
TYP.
0.310 (7.9) 0.160 (4.1)
0.290 (7.4) 0.140 (3.5)
• Plastic package has Underwriters Laboratory
0.740 (18.8) Flammability Classification 94V-0
0.720 (18.3) • This series is UL listed under the Recognized
0.085 (2.16)
0.075
(1.9)R. 0.080 (2.03) Component Index, file number E54214
0.065 (1.65) 0.060 (1.52)
• High case dielectric strength of 1500 VRMS
5o
TYP. • Ideal for printed circuit boards
0.085 (2.16) • Glass passivated chip junction
0.710 (18.0) 0.075 (1.90)
0.690 (17.5)
• High surge current capability
0.100 (2.54)
0.085 (2.16)
0.050 (1.27) • High temperature soldering guaranteed:
0.040 (1.02)
260°C/10 seconds, 0.375 (9.5mm) lead length,
5lbs. (2.3kg) tension
0.022 (0.56)
0.080 (2.03) 0.190 (4.83) 0.018 (0.46)
0.065 (1.65) 0.210 (5.33)
Mechanical Data
Polarity shown on front side of case, positive lead by beveled corner Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
If preferred, marking on front side of case may be on reverse side of case. Lead
forming option with 10mm-7.5mm spacing is available. Method 2026
Mounting Position: Any (NOTE 3)
Dimensions in inches and (millimeters)
Mounting Torque: 5 in. - lb. max.
Weight: 0.15 ounce, 4.0 grams

Maximum Ratings & Thermal Characteristics Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS G5SBA20 G5SBA60 UNITS

Maximum repetitive peak reverse voltage VRRM 200 600 V
Maximum RMS voltage VRMS 140 420 V
Maximum DC blocking voltage VDC 200 600 V
Maximum average forward TC=100 C (NOTE 1)
O
6.0
IF(AV) A
rectified output current at TA=25OC (NOTE 2) 2.8
Peak forward surge current single
sine-wave superimposed on rated load IFSM 150 A
(JEDEC Method)
Rating for fusing (t<8.3ms) I2t 60 A2sec
Typical thermal resistance per leg (NOTE 2) RΘJA 22
°C/W
(NOTE 1) RΘJC 3.4
Operating junction storage and temperature range TJ, TSTG -55 to +150 °C

Electrical Characteristics Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS G5SBA20 G5SBA60 UNITS

Maximum instantaneous forward voltage
VF 1.05 V
drop per leg at 3.0 A
Maximum DC reverse current at rated TA= 25°C 5.0
IR µA
DC blocking voltage per leg TA=125°C 300
Notes:
(1) Unit case mounted on Al plate heatsink
(2) Units mounted on P.C.B. with 0.5 x 0.5” (12 x 12mm) copper pads and 0.375” (9.5mm) lead length
(3) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw 10/5/99
 G5SBA20 and G5SBA60
Ratings and Characteristic Curves (T A = 25°C unless otherwise noted)

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD

SURGE CURRENT PER LEG

PEAK FORWARD SURGE CURRENT,

FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
AVERAGE FORWARD OUTPUT

150
8.0 TJ=TJ max.
SINGLE SINE-WAVE
CURRENT, AMPERES

HEATSINK MOUNTING, TC (JEDEC Method

6.0

AMPERES
100

4.0

50
2.0
P.C.B. MOUNTING, TA 1.0 CYCLE
0 0
0 50 100 150 1 10 100
NUMBER OF CYCLES AT 60 Hz
TEMPERATURE, °C

FIG. 4 - TYPICAL REVERSE

FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG
CHARACTERISTICS PER LEG
100 500
INSTANTANEOUS REVERSE CURRENT,
INSTANTANEOUS FORWARD CURRENT,

100
TJ=125OC
10
MICROAMPERES

10
AMPERES

TJ=25OC
1 PULSE WIDTH = 300µs
1% DUTY CYCLE 1

0.1
0.1
TJ=25°C

0.01 0.01
0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 20 40 60 80 100

INSTANTANEOUS FORWARD VOLTAGE, PERCENT OF RATED PEAK REVERSE

VOLTS VOLTAGE, %

FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 6 - TYPICAL TRANSIENT THERMAL

PER LEG IMPEDANCE
1,000 100
TRANSIENT THERMAL IMPEDANCE,

TJ=25OC
f=1.0 MHZ
JUNCTION CAPACITANCE, pF

VSIG=50mVp-p

10
°C/W

100

10
0.1 1 10 100 0.1
0.01 0.1 1 10 100
REVERSE VOLTAGE, VOLTS
t, HEATING TIME, sec.