Product Name: INOX-mx3 Aerosol

Page: 1 of 6
This version issued: May, 2017

Section 1 - Identification of the Material and Supplier

Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
65 Chetwynd Street Fax: 07 3209 8744
Loganholme QLD 4129 Emergency 0439 788 748 (5 p.m. – 8 a.m.) weekdays.
24 Hours weekends and Public Holidays
Chemical nature: Oil blend dispensed as an aerosol
Trade Name: INOX-mx3 Aerosol
Product Code: 00003 (100 g), 00001 (300 g)
Product Use: Anti-corrosion, anti-moisture penetrating oil
Creation Date: November, 2016
This version issued: May, 2017 and is valid for 5 years from this date.
Poisons Information Centre: Phone 13 1126 from anywhere in Australia

Section 2 - Hazards Identification

Statement of Hazardous Nature
This product is classified as: F+, Extremely Flammable. Not classified as hazardous according to the criteria of
SWA.
Dangerous according to Australian Dangerous Goods (ADG) Code, IATA and IMDG/IMSBC criteria.
SUSMP Classification: None allocated.
ADG Classification: Class 2.1: Flammable gases.
UN Number: 1950, AEROSOLS

GHS Signal word: DANGER

Flammable aerosols Category 2
Gases under pressure - Compressed gas or liquefied gas or dissolved gas
HAZARD STATEMENT:
H223: Flammable aerosol
H280: Contains gas under pressure; may explode if heated.
PREVENTION
P210: Keep away from heat, sparks, open flames and hot surfaces. - No smoking.
P211: Do not spray on an open flame or other ignition source.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical ventilating, lighting and other equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P251: Pressurized container: Do not pierce or burn, even after use.
P261: Avoid breathing fumes, mists, vapours or spray.
P262: Do not get in eyes, on skin, or on clothing.
P271: Use only outdoors or in a well ventilated area.
P280: Wear protective gloves, protective clothing and eye or face protection.
RESPONSE
P362: Take off contaminated clothing and wash before reuse.
P301+P330+P331: IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303+P361+P353: IF ON SKIN (or hair): Remove immediately all contaminated clothing. Rinse skin with water.
P372: Explosion risk in case of fire.
P381: Eliminate all ignition sources if safe to do so.
P370+P378: In case of fire, use carbon dioxide, dry chemical, foam. Water fog or fine spray is the preferred
medium for large fires.

SAFETY DATA SHEET

Issued by: Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand)
 Product Name: INOX-mx3 Aerosol
Page: 2 of 6
This version issued: May, 2017

STORAGE
P402: Store in a dry place.
P403: Store in a well-ventilated place.
P410+P412: Store below 30°C, protect from direct sunlight and do not expose to temperatures exceeding
50°C.
DISPOSAL
P501: If they can not be recycled, dispose of contents to an approved waste disposal plant and containers to
landfill (see Section 13 of this SDS).
Emergency Overview
Physical Description & Colour: Aerosol, dispensed product is a clear light tan liquid
Odour: Mild odour.
Major Health Hazards: no significant risk factors have been found for this product.

Section 3 - Composition/Information on Ingredients

Ingredients CAS No Conc, % TWA (mg/m3) STEL (mg/m3)
Butane 106-97-8 <30 1900 not set
Propane 74-98-6 <10 not set not set
Ketone secret <5 100 not set
Other non hazardous ingredients secret to 100 not set not set
This is a commercial product whose exact ratio of components may vary slightly. Minor quantities of other non
hazardous ingredients are also possible.
The SWA TWA exposure value is the average airborne concentration of a particular substance when calculated over a normal 8 hour working day
for a 5 day working week. The STEL (Short Term Exposure Limit) is an exposure value that may be equalled (but should not be exceeded) for no
longer than 15 minutes and should not be repeated more than 4 times per day. There should be at least 60 minutes between successive exposures
at the STEL. The term "peak "is used when the TWA limit, because of the rapid action of the substance, should never be exceeded, even briefly.

Section 4 - First Aid Measures

General Information:
You should call The Poisons Information Centre if you feel that you may have been poisoned, burned or irritated by
this product. The number is 13 1126 from anywhere in Australia (0800 764 766 in New Zealand) and is available at all
times. Have this SDS with you when you call.
Inhalation: No first aid measures normally required. However, if inhalation has occurred, and irritation has
developed, remove to fresh air and observe until recovered. If irritation becomes painful or persists more than about
30 minutes, seek medical advice.
Skin Contact: Irritation is unlikely. However, if irritation does occur, flush with lukewarm, gently flowing water for 5
minutes or until chemical is removed.
Eye Contact: Immediately flush the contaminated eye(s) with lukewarm, gently flowing water for 5 minutes or until
the product is removed, while holding the eyelid(s) open. Obtain medical advice immediately if irritation occurs. Take
special care if exposed person is wearing contact lenses.
Ingestion: If product is swallowed or gets in mouth, do NOT induce vomiting; wash mouth with water and give some
water to drink. If symptoms develop, or if in doubt contact a Poisons Information Centre or a doctor.
Section 5 - Fire Fighting Measures
Fire and Explosion Hazards: The major hazard in fires is usually inhalation of heated and toxic or oxygen
deficient (or both), fire gases. There is a moderate risk of an explosion from this product if commercial quantities are
involved in a fire. Firefighters should take care and appropriate precautions.
Fire decomposition products from this product may be toxic if inhaled. Take appropriate protective measures.
Extinguishing Media: In case of fire, use carbon dioxide, dry chemical, foam. Water fog or fine spray is the
preferred medium for large fires. Try to contain spills, minimise spillage entering drains or water courses.
Fire Fighting: If a significant quantity of this product is involved in a fire, call the fire brigade. There is a danger of a
violent reaction or explosion if significant quantities of this product are involved in a fire. Recommended personal
protective equipment is full fire kit and breathing apparatus.
Flash point: Propellant is flammable. Dispensed product has a flash point of 182°C when
propellant gas has dissipated.
Upper Flammability Limit: Not available

SAFETY DATA SHEET

Issued by: Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand)
 Product Name: INOX-mx3 Aerosol
Page: 3 of 6
This version issued: May, 2017

Lower Flammability Limit: Not available

Autoignition temperature: No data.
Flammability Class: No data.

Section 6 - Accidental Release Measures

Accidental release: In the event of a major spill, prevent spillage from entering drains or water courses. Evacuate
the spill area and deny entry to unnecessary and unprotected personnel. As a minimum, wear overalls, goggles and
gloves. Suitable materials for protective clothing include no specific manufacturer recommendations. Use
impermeable gloves with care. Eye/face protective equipment should comprise, as a minimum, protective glasses
and, preferably, goggles. If there is a significant chance that vapours or mists are likely to build up in the cleanup
area, we recommend that you use a respirator. Usually, no respirator is necessary when using this product. However,
if you have any doubts consult the Australian Standard mentioned below (section 8). Otherwise, not normally
necessary.
Stop leak if safe to do so, and contain spill. Absorb onto sand, vermiculite or other suitable absorbent material. If spill
is too large or if absorbent material is not available, try to create a dike to stop material spreading or going into drains
or waterways. Take suitable precautions e.g. use of non-sparking equipment to avoid creating sparks or flames which
may ignite the spilled material. Leaking gases may form an explosion hazard. Any equipment capable of building an
electrostatic charge should be electrically grounded. Sweep up and shovel or collect recoverable product into labelled
containers for recycling or salvage, and dispose of promptly. Recycle containers wherever possible after careful
cleaning. After spills, wash area preventing runoff from entering drains. If a significant quantity of material enters
drains, advise emergency services. This material may be suitable for approved landfill. Ensure legality of disposal by
consulting regulations prior to disposal. Thoroughly launder protective clothing before storage or re-use. Advise
laundry of nature of contamination when sending contaminated clothing to laundry.
Section 7 - Handling and Storage
Handling: Keep exposure to this product to a minimum, and minimise the quantities kept in work areas. Check
Section 8 of this SDS for details of personal protective measures, and make sure that those measures are followed.
The measures detailed below under "Storage" should be followed during handling in order to minimise risks to
persons using the product in the workplace. Also, avoid contact or contamination of product with incompatible
materials listed in Section 10.
Storage: Store in a cool (below 30°C), well ventilated area. Protect from direct sunlight. Make sure that surrounding
electrical devices and switches are suitable. Check containers and valves periodically for leaks. If you keep more than
25kg of flammable gases, you are probably required to license the premises or notify your Dangerous Goods
authority. If you have any doubts, we suggest you contact your Dangerous Goods authority in order to clarify your
obligations. Check packaging - there may be further storage instructions on the label.
Section 8 - Exposure Controls and Personal Protection
The following Australian Standards will provide general advice regarding safety clothing and equipment:
Respiratory equipment: AS/NZS 1715, Protective Gloves: AS 2161, Occupational Protective Clothing: AS/NZS 4501
set 2008, Industrial Eye Protection: AS1336 and AS/NZS 1337, Occupational Protective Footwear: AS/NZS2210.
SWA Exposure Limits TWA (mg/m3) STEL (mg/m3)
Butane 1900 not set
Ketone 100 not set
No special equipment is usually needed when occasionally handling small quantities. The following instructions are
for bulk handling or where regular exposure in an occupational setting occurs without proper containment systems.
Ventilation: This product should only be used in a well ventilated area. If natural ventilation is inadequate, use of a
fan is suggested.
Eye Protection: Eye protection such as protective glasses or goggles is recommended when this product is being
used.
Skin Protection: The information at hand indicates that this product is not harmful and that normally no special skin
protection is necessary. However, we suggest that you routinely avoid contact with all chemical products and that you
wear suitable gloves (preferably elbow-length) when skin contact is likely.
Protective Material Types: There is no data that enables us to recommend any type except that it should be
impermeable.
Respirator: Usually, no respirator is necessary when using this product. However, if you have any doubts consult
the Australian Standard mentioned above. Otherwise, not normally necessary.

SAFETY DATA SHEET

Issued by: Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand)
 Product Name: INOX-mx3 Aerosol
Page: 4 of 6
This version issued: May, 2017

Section 9 - Physical and Chemical Properties:

Physical Description & colour: Aerosol, dispensed product is a clear light tan liquid
Odour: Mild odour.
Boiling Point: Not available.
Freezing/Melting Point: -18°C
Volatiles: No data.
Vapour Pressure: <6 kPa (dispensed product)
Vapour Density: No data.
Specific Gravity: 0.840 (dispensed product)
Water Solubility: Negligible.
pH: No data.
Volatility: No data.
Odour Threshold: No data.
Evaporation Rate: No data.
Coeff Oil/water Distribution: No data
Autoignition temp: No data.
Section 10 - Stability and Reactivity
Reactivity: This product is unlikely to react or decompose under normal storage conditions. However, if you have
any doubts, contact the supplier for advice on shelf life properties.
Conditions to Avoid: Store below 30°C, protect from direct sunlight and do not expose to temperatures exceeding
50°C. Keep containers tightly closed. Keep containers and surrounding areas well ventilated. Keep away from
sources of sparks or ignition. Any electrical equipment in the area of this product should be flame proofed. Protect this
product from light.
Incompatibilities: strong oxidising agents, flammable liquids, corrosive materials.
Fire Decomposition: Combustion forms carbon dioxide, and if incomplete, carbon monoxide and possibly smoke.
Water is also formed. Carbon monoxide poisoning produces headache, weakness, nausea, dizziness, confusion,
dimness of vision, disturbance of judgment, and unconsciousness followed by coma and death.
Polymerisation: This product will not undergo polymerisation reactions.

Section 11 - Toxicological Information

Local Effects:
Target Organs: There is no data to hand indicating any particular target organs.

Classification of Hazardous Ingredients

Ingredient Risk Phrases
Propane No risk phrases
 Flammable gas - category 1
 Gas under pressure

Ketone No risk phrases at concentrations found in this product

 Flammable liquid - category 3
 Acute toxicity - category 4

Potential Health Effects

Inhalation:
Short Term Exposure: Available data indicates that this product is not harmful. However product may be mildly
irritating, although unlikely to cause anything more than mild transient discomfort. Intentional misuse by deliberately
concentrating and inhaling contents of aerosol containers can be harmful or fatal.
Long Term Exposure: No data for health effects associated with long term inhalation.
Skin Contact:
Short Term Exposure: Major health effect from this product is misuse of the aerosol function. If sprayed
continuously on skin or in eyes, it can cause frostbite.
SAFETY DATA SHEET
Issued by: Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand)
 Product Name: INOX-mx3 Aerosol
Page: 5 of 6
This version issued: May, 2017

Long Term Exposure: No data for health effects associated with long term skin exposure.
Eye Contact:
Short Term Exposure: If sprayed directly in the eye, this product will irritate. If spraying is prolonged, it may cause
damage through frostbite.
Long Term Exposure: No data for health effects associated with long term eye exposure.
Ingestion:
Short Term Exposure: Significant oral exposure is considered to be unlikely. This product, while believed to be not
harmful, is likely to cause headache and gastric disturbance such as nausea and vomiting if ingested in significant
quantities. However, this product may be irritating to mucous membranes but is unlikely to cause anything more than
transient discomfort.
Long Term Exposure: No data for health effects associated with long term ingestion.
Carcinogen Status:
SWA: No significant ingredient is classified as carcinogenic by SWA.
NTP: No significant ingredient is classified as carcinogenic by NTP.
IARC: Ketone is Class 3 - unclassifiable as to carcinogenicity to humans.
See the IARC website for further details. A web address has not been provided as addresses frequently change.
Section 12 - Ecological Information
Insufficient data to be sure of status.

Section 13 - Disposal Considerations

Disposal: This product may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for
its intended use. If it has been contaminated, it may be possible to reclaim the product by filtration, distillation or some
other means. If neither of these options is suitable in-house, consider controlled incineration, or contact a specialist
waste disposal company. Do not puncture or incinerate aerosol cans, even when empty.

Section 14 - Transport Information

Dangerous according to Australian Dangerous Goods (ADG) Code, IATA and IMDG/IMSBC criteria.
UN Number: 1950, AEROSOLS
Hazchem Code: 2YE
Special Provisions: 63, 190, 277
Limited quantities: ADG 7 specifies a Limited Quantity value of 1000mL for this class of product.
Dangerous Goods Class: Class 2.1: Flammable gases.
Packing Group: Not set
Packing Instruction: P003
Class 2.1 Flammable gases shall not be loaded in the same vehicle or packed in the same freight container with
Classes 1 (Explosives), 3 (Flammable Liquids) (where both flammable liquids and flammable gases are in bulk), 4.1
(Flammable Solids), 4.2 (Spontaneously Combustible Substances), 4.3 (Dangerous When Wet Substances), 5.1
(Oxidising Agents), 5.2 (Organic Peroxides), and 7 (Radioactive Substances). They may however be loaded in the
same vehicle or packed in the same freight container with Classes 2.2 (Non-flammable Non-Toxic gases), 3
(Flammable liquids except where both flammable liquids and flammable gases are in bulk), 6 (Toxic Substances), 8
(Corrosive Substances) 9 (Miscellaneous dangerous goods), Foodstuffs and foodstuff empties.

Section 15 - Regulatory Information

AICS: All of the significant ingredients in this formulation are compliant with NICNAS regulations.
Section 16 - Other Information
This SDS contains only safety-related information. For other data see product literature.
Acronyms:
ADG Code Australian Code for the Transport of Dangerous Goods by Road and Rail (7th edition)
AICS Australian Inventory of Chemical Substances
SWA Safe Work Australia, formerly ASCC and NOHSC
CAS number Chemical Abstracts Service Registry Number

SAFETY DATA SHEET

Issued by: Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand)
 Product Name: INOX-mx3 Aerosol
Page: 6 of 6
This version issued: May, 2017

Hazchem Code Emergency action code of numbers and letters that provide information to emergency
services especially firefighters
IARC International Agency for Research on Cancer
NOS Not otherwise specified
NTP National Toxicology Program (USA)
R-Phrase Risk Phrase
SUSMP Standard for the Uniform Scheduling of Medicines & Poisons
UN Number United Nations Number
THIS SDS SUMMARISES OUR BEST KNOWLEDGE OF THE HEALTH AND SAFETY HAZARD INFORMATION OF THE PRODUCT AND HOW
TO SAFELY HANDLE AND USE THE PRODUCT IN THE WORKPLACE. EACH USER MUST REVIEW THIS SDS IN THE CONTEXT OF HOW
THE PRODUCT WILL BE HANDLED AND USED IN THE WORKPLACE.
IF CLARIFICATION OR FURTHER INFORMATION IS NEEDED TO ENSURE THAT AN APPROPRIATE RISK ASSESSMENT CAN BE MADE,
THE USER SHOULD CONTACT THIS COMPANY SO WE CAN ATTEMPT TO OBTAIN ADDITIONAL INFORMATION FROM OUR SUPPLIERS
OUR RESPONSIBILITY FOR PRODUCTS SOLD IS SUBJECT TO OUR STANDARD TERMS AND CONDITIONS, A COPY OF WHICH IS SENT
TO OUR CUSTOMERS AND IS ALSO AVAILABLE ON REQUEST.

Please read all labels carefully before using product.

This SDS is prepared in accord with the SWA document “Preparation of Safety Data Sheets for Hazardous
Chemicals - Code of Practice” (Feb 2016)
Copyright © Kilford & Kilford Pty Ltd, May, 2017.
http://www.kilford.com.au/ Phone (02)9251 4532

SAFETY DATA SHEET

Issued by: Candan Industries Pty Ltd Phone: 07 3209 8733 (office hours)
Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand)