WJ ENGINE 9-1

ENGINE
TABLE OF CONTENTS

page page

DESCRIPTION AND OPERATION OIL PAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

ENGINE IDENTIFICATION . . . . . . . . . . . . . . . . . . . 1 OIL PUMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
HYDRAULIC TAPPETS . . . . . . . . . . . . . . . . . . . . . 2 OIL PUMP PRESSURE RELIEF VALVE . . . . . . . . 46
DIAGNOSIS AND TESTING PISTONS AND CONNECTING ROD
SERVICE DIAGNOSIS—DIESEL— ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
MECHANICAL. . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ROCKER ARMS AND PUSH RODS . . . . . . . . . . 31
SERVICE DIAGNOSIS—DIESEL— TIMING GEAR COVER . . . . . . . . . . . . . . . . . . . . 41
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . 3 TIMING GEAR COVER OIL SEAL . . . . . . . . . . . . 40
TAPPET NOISE . . . . . . . . . . . . . . . . . . . . . . . . . . 11 TRANSMISSION PILOT BUSHING . . . . . . . . . . . 53
SERVICE PROCEDURES VALVE SPRINGS. . . . . . . . . . . . . . . . . . . . . . . . . 31
VALVE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . 11 VIBRATION DAMPER . . . . . . . . . . . . . . . . . . . . . 40
REMOVAL AND INSTALLATION DISASSEMBLY AND ASSEMBLY
3.1L TURBO DIESEL ENGINE. . . . . . . . . . . . . . . 13 HYDRAULIC TAPPETS . . . . . . . . . . . . . . . . . . . . 58
CAMSHAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 CLEANING AND INSPECTION
CAMSHAFT BEARINGS. . . . . . . . . . . . . . . . . . . . 44 CYLINDER HEAD . . . . . . . . . . . . . . . . . . . . . . . . 59
CRANKSHAFT AND MAIN BEARINGS . . . . . . . . 55 CYLINDER WALL LINER ASSEMBLY . . . . . . . . . 61
CYLINDER HEAD COVER . . . . . . . . . . . . . . . . . . 28 OIL PUMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
CYLINDER WALL LINER ASSEMBLY . . . . . . . . . 51 PISTONS AND CONNECTING ROD
ENGINE CYLINDER HEAD . . . . . . . . . . . . . . . . . 33 ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
ENGINE OIL FILTER . . . . . . . . . . . . . . . . . . . . . . 48 ROCKER ARMS AND PUSH RODS . . . . . . . . . . 59
EXHAUST AND INTAKE MANIFOLD . . . . . . . . . . 24 SPECIFICATIONS
FLEXPLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 ENGINE SPECIFICATIONS. . . . . . . . . . . . . . . . . . 62
HYDRAULIC TAPPETS . . . . . . . . . . . . . . . . . . . . 29 TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . 63
INTERNAL VACUUM PUMP . . . . . . . . . . . . . . . . 45 SPECIAL TOOLS
OIL FILTER ADAPTER AND OIL COOLER . . . . . 47 SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . 65

DESCRIPTION AND OPERATION

ENGINE IDENTIFICATION
DESCRIPTION
The engine model code and serial number are
stamped on the left side of the engine block, just
below the oil dipstick tube (Fig. 1). The model code
for the 3.1L is 73B followed by a five digit serial
number.

Fig. 1 Engine Code Location

9-2 ENGINE WJ
DESCRIPTION AND OPERATION (Continued)
Displacement . . . . . . . . . . . . . . . . . . . 3.1L (3125cc) has no oil pressure gauge, install a reliable gauge at
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92.00 mm the pressure sending unit. The pressure should be 50
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . 94.00 mm psi at 3000 RPM.
Compression Ratio . . . . . . . . . . . . . . . . . . . . . . 21:1 Check the oil level after the engine reaches normal
Vacuum at idle . . . . . . . . . 600 mm/Hg (23.6 In/Hg) operating temperature. Allow 5 minutes to stabilize
Belt Tension . . . . . . 400/500N Automatic Tensioner oil level, check dipstick. The oil level in the pan
Thermostat Opening . . . . . . . . . . . . . . . 80°C 6 2°C should never be above the FULL mark or below the
Generator Rating . . . . . . . . . . . . . . . . . Denso 130A ADD OIL mark on dipstick. Either of these 2 condi-
Cooling System Capacity . . . . . . . . . . . . . . 9.5 Liter tions could be responsible for noisy tappets:
P/S Capacity . . . . . . . . . . . . . . . . . . . . . . 0.75 Liter OIL LEVEL HIGH
Engine Oil Capacity . . . . . 7.5 Liter w/filter change If oil level is above the FULL mark, it is possible
for the connecting rods to dip into the oil. With the
Timing System . . Pushrod operated overhead valves,
engine running, this condition could create foam in
with gear-driven camshaft in crankcase.
the oil pan. Foam in oil pan would be fed to the
Air Intake . . . . . . . . . . . . . . . . . . . . . . . . Dry filter.
hydraulic tappets by the oil pump causing them to
Fuel feed . . . . Vane pump incorporated in injection
lose length and allow valves to seat noisily.
pump.
OIL LEVEL LOW
Fuel System . . . . . . . . . . . . . Indirect fuel injection
Low oil level may allow oil pump to take in air.
(precombustion chamber).
When air is fed to the tappets, they lose length which
Combustion Cycle . . . . . . . . . . . . . . . . . . . 4 stroke.
allows valves to seat noisily. Any leaks on intake side
Cooling System . . . . . . . . . . . . . . . . . Water cooling. of oil pump through which air can be drawn will cre-
Injection Pump . . . . . . Rotary pump with electronic ate the same tappet action. Check the lubrication
management. system from the intake strainer to the pump cover,
Lubrication . . Pressure lubrication by rotary pump, including the relief valve retainer cap. When tappet
full-flow filtration. noise is due to aeration, it may be intermittent or
Engine Rotation . . . . . . . . . Clockwise viewed from constant, and usually more than 1 tappet will be
front cover. noisy. When oil level and leaks have been corrected,
operate the engine at fast idle. Run engine for a suf-
Engine Description ficient time to allow all of the air inside the tappets
to be bled out.
HYDRAULIC TAPPETS
DESCRIPTION
Before disassembling any part of the engine to cor-
rect tappet noise, check the oil pressure. If vehicle
WJ ENGINE 9-3

DIAGNOSIS AND TESTING

SERVICE DIAGNOSIS—DIESEL—PERFORMANCE
CONDITION POSSIBLE CAUSES CORRECTION

ENGINE WILL NOT CRANK 1. Starting motor operating, but not 1. Remove the starter motor. Check for broken
OR CRANKS SLOWLY cranking the engine. flywheel teeth or a broken starting motor
spring.
2. Crankshaft rotation restricted. 2. Rotate the engine to check for rotational
resistance.
3. Starting circuit connections loose 3. Clean and tighten connections.
or corroded.
4. Neutral safety switch or starter 4. Check starter relay supply voltage and
relay inoperative. proper operation of neutral safety switch (if
equipped). Replace defective parts.
5. Battery charge low. 5. Check battery voltage. Replace battery if a
charge cannot be held.
6. No voltage to starter solenoid. 6. Check voltage to solenoid. If necessary,
replace the solenoid.
7. Solenoid or starter motor 7. Replace starter motor.
inoperative.

ENGINE CRANKS, BUT WILL 1. No fuel in supply tank. 1. Fill fuel supply.
NOT START NO SMOKE
2. Electrical fuel shutdown solenoid 2. Check for loose wires and verify that the
not operating. fuel shutdown solenoid and fuel shutdown
solenoid relay is functioning.
3. Exhaust plugged. 3. Remove the obstruction.
4. Fuel filter plugged. 4. Drain fuel/water separator and replace fuel
filter.
5. Excessive fuel inlet restriction. 5. Check fuel inlet restriction. Correct cause.
6. Injection pump not getting fuel or 6. Check fuel flow/bleed fuel system.
fuel is aerated.
7. Worn or inoperative injection 7. Visually check delivery with externally
pump. connected injector to one of the pump outlets.
Repair or replace the pump if fuel is not being
delivered.

ENGINE HARD TO START, 1. Incorrect starting procedure. 1. The fuel shutoff solenoid control must be in
OR WILL NOT START SMOKE the run position. Ensure proper procedure is
FROM EXHAUST being used.
2. Cranking speed too slow. 2. (A) Verify that the transmission is not
engaged.
(B) Check the battery, starting motor and look
for loose or corroded wiring connections.
3. Cylinder heads heater plugs relay 3. Verify system is working. Repair/replace
defective. inoperative parts.
4. One or more cylinder head heater 4. Verify system is working. Repair/replace
plugs defective. inoperative parts.
5. Insufficient intake air. 5. Inspect or replace filter and check for
obstruction to the air supply tube.
9-4 ENGINE WJ
DIAGNOSIS AND TESTING (Continued)

CONDITION POSSIBLE CAUSES CORRECTION

ENGINE HARD TO START, 6. Air in fuel system or the fuel 6. Check the flow through the filter and bleed
OR WILL NOT START supply is inadequate. the system. Locate and eliminate the air
SMOKE FROM EXHAUST source.
(CONT.)
7. Contaminated fuel. 7. Verify by operating the engine with clean
fuel from a temporary tank. Check for
presence of gasoline. Drain and flush fuel
supply tank. Replace fuel/water separator filter.
8. Fuel screen plugged. 8. Check fuel screen.
9. One or more injectors worn or not 9. Check/replace improperly operating
operating properly. injectors.
10. Worn or inoperative injection 10. Visually check fuel delivery with an
pump. externally connected injector to one of the
pump outlets. Repair or replace the pump if
fuel is not being delivered.
11. Injection pump out of time. 11. Check/Time the pump (refer to Group 14,
Fuel System).
12. Engine compression low. 12. Check compression to identify the
problem.
13. Camshaft out of time. 13. Check camshaft timing.

ENGINE STARTS, BUT WILL 1. Cylinder heads heater plugs relay 1. Verify system is working. Repair/replace
NOT KEEP RUNNING defective. inoperative parts.
2. One or more cylinder head heater 2. Verify system is working. Repair/replace
plugs defective. inoperative parts.
3. Intake air or exhaust system 3. Visually check for exhaust restriction and
restricted. inspect the air intake.
4. Air in the fuel supply system or 4. Check flow through the filter and bleed the
the fuel supply is inadequate. system. Locate and eliminate the air source.
5. Fuel waxing due to extremely 5. Verify by inspecting the fuel filter. Clean the
cold weather. system and use climatized fuel. Replace
fuel/water separator filter. Check fuel heater
for proper operation.
6. Contaminated fuel. 6. Verify by operating the engine with clean
fuel from a temporary supply tank. Check for
presence of gasoline. Replace fuel/water
separator filter.

SURGING (SPEED CHANGE) 1. If the condition occurs at idle, the 1. Adjust the idle speed.
idle speed is set too low for the
accessories.
2. High pressure fuel leak. 2. Inspect/correct leaks in the high pressure
lines. Fitting and delivery valve sealing
washers.
3. One or more injectors worn or not 3. Check/replace the inoperative injectors.
operating properly.
4. Improperly operating injection 4. Replace the injector pump.
pump.
WJ ENGINE 9-5
DIAGNOSIS AND TESTING (Continued)

CONDITION POSSIBLE CAUSES CORRECTION

ROUGH IDLE (IRREGULARLY 1. If engine is cold, glow plug relay 1. Refer to troubleshooting for cylinder head
FIRING OR ENGINE on glow plug(s) defective. heater plugs (see Group 14, Fuel system).
SHAKING) 2. Engine mounts damaged or 2. Repair or replace mounts.
loose.
3. High pressure fuel leaks. 3. Correct leaks in the high pressure lines,
fittings or delivery valves.
4. Air in the fuel system. 4. Bleed the fuel system and eliminate the
source of the air.
5. Sticking needle valve in an 5. Check and replace the injector with the
injector. sticking needle valve.

ENGINE RUNS ROUGH 1. Fuel injection lines leaking. 1. Correct leaks in the high pressure lines,
fittings, injectors sealing washers or delivery
valves.
2. Air in the fuel or the fuel supply is 2. Check the flow through the filter and bleed
inadequate. the system. Locate and eliminate the air
source.
3. Contaminated fuel. 3. Verify by operating the engine with clean
fuel from a temporary supply tank. Check for
presence of gasoline. Replace fuel/water
separator filter.
4. Incorrect valve operation. 4. Check for a bent push rod and adjust
valves. Replace push rod, if necessary.
5. Injection pump timing incorrect. 5. Check/time pump (refer to Group 14, Fuel
System).
6. Improperly operating injectors. 6. Replace inoperative injectors.
7. Defective injection pump (delivery 7. Repair or replace injection pump.
valve).
8. Camshaft out of time. 8. Check/correct gear train timing alignment.
9. Damaged camshaft or tappets. 9. Inspect camshaft valve lift. Replace
camshaft and tappets.
10. Automatic timing advance not 10. Check injection pump. Check fuel injector
operating. sensor at number 1 cylinder injector.

ENGINE RPM WILL NOT 1. Engine overload. 1. Verify high idle speed without load.
REACH RATED SPEED Investigate operation to be sure correct gear is
being used.
2. Improperly operating tachometer. 2. Verify engine speed with hand tachometer,
correct as required.
3. Inadequate fuel supply. 3. Check the fuel flow through the system to
locate the reason for inadequate fuel supply,
correct as required.
4. Air/fuel controls leak. 4. Check and repair leak. Check AFC tubing
for obstruction.
9-6 ENGINE WJ
DIAGNOSIS AND TESTING (Continued)

CONDITION POSSIBLE CAUSES CORRECTION

ENGINE RPM WILL NOT 6. Improperly operating injection 6. Repair or replace injection pump.
REACH RATED SPEED pump.
(CONT.)

LOW POWER 1. Fuel control lever not moving to 1. Check/correct for stop-to-stop travel.
full throttle.
2. High oil level. 2. Check/correct oil level.
3. Engine overloaded. 3. Check for added loading from accessories
or driven units, brakes dragging and other
changes in vehicle loading. Repair/replace as
needed.
4. Slow throttle response caused by 4. Check for leaks and obstructions. Tighten
leaking or obstructed air control the fittings. Repair or replace the pump if the
tube or improperly operating control controls are not functioning.
in the pump.
5. Inadequate intake air flow. 5. Inspect/replace air cleaner element. Look
for other restrictions.
6. Inadequate fuel supply. Air in the 6. Check the flow through the filter to locate
fuel. the source of the restriction. Check fuel
pressure and inlet restriction.
7. Excessive exhaust restriction. 7. Check/correct the restriction in the exhaust
system.
8. High fuel temperature. 8. Verify that fuel heater is off when engine is
warm. Check for restricted fuel drain tubes.
Repair/replace as needed.
9. Poor quality fuel or fuel 9. Verify by operating from a temporary tank
contaminated with gasoline. with good fuel. Check for presence of
gasoline. Replace fuel/water separator filter.
10. Air leak between the 10. Check/correct leaks in hoses, gaskets,
turbocharger and the intake charge air cooler and around mounting
manifold. capscrews or through holes in the manifold
cover.
11. Exhaust leak at the manifold or 11. Check/correct leaks in the manifold or
turbocharger. turbocharger gaskets. If manifold is cracked,
replace manifold.
12. Improperly operating 12. Inspect/replace turbocharger.
turbocharger.
13. Wastegate operation. 13. Check wastegate operation.
14. Valve not operating. 14. Check for bent push rod, replace if
necessary.
15. Worn or improperly operating 15. Check/replace injectors.
injectors.
16. Incorrect injection pump timing. 16. Verify injection pump timing (see Group
14, Fuel System).
17. Improperly operating injection 17. Repair or replace injection pump.
pump.
WJ ENGINE 9-7
DIAGNOSIS AND TESTING (Continued)

CONDITION POSSIBLE CAUSES CORRECTION

EXCESSIVE EXHAUST 1. Engine running too cold (white 1. Refer to troubleshooting for coolant
SMOKE smoke). temperature below normal (refer to Group 7,
Cooling System). Inspect cylinder head heater
plugs for proper operation.

2. Improper starting procedure 2. Use proper starting procedures.

(white smoke).
3. Fuel supply inadequate. 3. Check fuel supply pressure and inlet
restriction.
4. Injection pump timing. 4. Check and time pump (refer to Group 14,
Fuel System).
5. Inadequate intake air. 5. Inspect/change air filter. Look for other
restriction. Check charge air cooler for
obstructions.
6. Air leak between turbocharger 6. Check/correct leaks in the air crossover
and intake manifold. tube, hoses, gaskets, mounting capscrews or
through holes in the manifold cover.
7. Exhaust leak at the manifold or 7. Check/correct leaks in the manifold or
turbocharger. turbocharger gaskets. If cracked replace
manifold.
8. Improperly operating 8. Inspect/replace turbocharger.
turbocharger.
9. Improperly operating injectors. 9. Check and replace inoperative injectors.
10. Improperly operating or 10. Repair or replace injection pump.
overfueled injector pump.
11. Piston rings not sealing (blue 11. Perform blow-by check. Correct as
smoke). required.

ENGINE WILL NOT SHUT- 1. Fuel shutoff solenoid inoperative. 1. Check/replace fuel shutoff solenoid.
OFF 2. Engine running on fumes drawn 2. Check the air intake ducts for the source of
into the air intake. fumes. WARNING: In case of engine
runaway due to flammable fumes from
gasoline spills or turbocharger oil leaks
being sucked into the engine, shut off
engine ignition switch first then use a CO2
fire extinguisher and direct the spray under
the front bumper to remove oxygen supply.
The engine air intake is on the passenger
side behind the bumper. The fire
extinguisher must be directed at this
location for emergency shutdown
conditions.
3. Fuel injection pump malfunction 3. Repair or replace fuel injection pump.
9-8 ENGINE WJ
DIAGNOSIS AND TESTING (Continued)

CONDITION POSSIBLE CAUSES CORRECTION

COOLANT TEMPERATURE 1. Low coolant level. 1. Check coolant level. Add coolant, if
ABOVE NORMAL necessary. Locate and correct the source of
the coolant loss, (refer to Group 7, Cooling).

2. Incorrect/improperly operating 2. Replace cap with the correct rating for the
pressure cap. system.
3. Loose drive belt on water 3. Check/replace belt or belt tensioner.
pump/fan.
4. Inadequate air flow to the 4. Check/repair radiator core, fan shroud and
radiator. viscous fan drive as required.
5. Radiator fins plugged. 5. Blow debris from fins.
6. Collapsed radiator hose. 6. Replace the hose. Check coolant tank cap
operation, (refer to Group 7, Cooling Tanks).
7. Improperly operating temperature 7. Verify that the gauge and temperature
sensor/gauge. sensor are accurate. Replace gauge/sensor, if
bad.
8. Improperly operating, incorrect or 8. check and replace the thermostat.
no thermostat.
9. Air in the cooling system. 9. (A) make sure the fill rate is not being
exceeded and the correct vented thermostat is
installed.
(B) Check for loose hose clamps. Tighten if
loose.
(C) If aeration continued, check for a
compresssion leak through the head gasket.
10. Inoperative water pump. 10. Check and replace the water pump.
11. Incorrect injection pump timing. 11. Verify pump timing marks are aligned.
Check/time the injector pump (refer to Group
14, Fuel System).
12. Overfueled injection pump. 12. Repair or replace the injection pump.
13. Plugged cooling passages in 13. Flush the system and fill with clean
radiator, head, head gasket or coolant.
block.
14. Engine overloaded. 14. Verify that the engine load rating is not
being exceeded.

COOLANT TEMPERATURE 1. Too much air flow across the 1. Check/repair viscous fan drive as required.
BELOW NORMAL radiator.
2. Incorrect thermostat or 2. Check and replace thermostat.
contamination in thermostat.
3. Temperature sensor or gauge 3. Verify that the gauge and sensor are
inoperative. accurate. If not, replace gauge/sensor.
4. Coolant not flowing by 4. Check and clean coolant passages.
temperature sensor.
WJ ENGINE 9-9
DIAGNOSIS AND TESTING (Continued)

SERVICE DIAGNOSIS—DIESEL—MECHANICAL.

CONDITION POSSIBLE CAUSES CORRECTION

LUBRICATING OIL 1. Low oil level. 1. (A) Check and fill with clean engine oil.
PRESSURE LOW (B) Check for a severe external oil leak that
could reduce the pressure.
2. Oil viscosity thin, diluted or 2. Verify the correct oil is being used. Check
wrong specification. for oil dilution.
3. Improperly operating pressure 3. Verify the pressure switch is functioning
switch/gauge. correctly. If not, replace switch/gauge.
4. Relief valve stuck open. 4. Check/replace valve.
5. If cooler was replaced, shipping 5. Check/remove shipping plugs.
plugs left in cooler.
6. Worn oil pump. 6. Check and replace oil pump.
7. Suction tube loose or seal 7. Check and replace seal.
leaking.
8. Loose main bearing cap. 8. Check and install new bearing and
tighten cap to proper torque.
9. Worn bearings or wrong 9. Inspect and replace connecting rod or
bearings installed. main bearings. Check and replace piston
cooling nozzles.
10. Oil jet under piston bad fit into 10. Check oil jet position.
cylinder block.

LUBRICATING OIL 1. Pressure switch/gauge not 1. Verify the pressure switch is functioning
PRESSURE TOO HIGH operating properly. correctly. If not, replace switch/gauge.
2. Engine running too cold. 2. Refer to Coolant Temperature Below
Normal (Engine Diagnosis Performance).
3. Oil viscosity too thick. 3. Make sure the correct oil being used,
(Refer to Group 0, Lubrication and
Maintenance).
4. Oil pressure relief valve stuck 4. Check and replace valve.
closed or binding.

LUBRICATING OIL LOSS 1. External leaks. 1. Visually inspect for oil leaks. Repair as
required.
2. Crankcase being overfilled. 2. Verify that the correct dipstick is being
used.
3. Incorrect oil specification or 3. (A) Make sure the correct oil is being
viscosity. used.
(B) Look for reduced viscosity from dilution
with fuel.
(C) Review/reduce the oil change intervals.
4. Oil cooler leak. 4. Check and replace the oil cooler.
5. High blow-by forcing oil out the 5. Check the breather tube area for signs of
breather. oil loss. Perform the required repairs.
9 - 10 ENGINE WJ
DIAGNOSIS AND TESTING (Continued)

CONDITION POSSIBLE CAUSES CORRECTION

LUBRICATING OIL LOSS 6. Turbocharger leaking oil to the 6. Inspect the air ducts for evidence of oil
(CONT.) air intake. transfer. Repair as required.
7. Piston rings not sealing (oil 7. Perform blow-by check. Repair as
being consumed by the engine.) required.

COMPRESSION KNOCKS 1. Poor quality fuel or water/ 1. Verify by operating from a temporary tank
gasoline contaminated fuel. with good fuel. Clean and flush the fuel
supply tanks. Replace fuel/water separator.
2. Incorrect injection pump timing. 2. Check and time injection pump (refer to
Group 14, Fuel System).
3. Improperly operating injectors. 3. Check and replace inoperative injectors.
4. Wrong injection pump timing. 4. Check injection pump timing.

EXCESSIVE VIBRATION 1. Loose or broken engine 1. Replace engine mounts.

mounts.
2. Damaged fan or improperly 2. Check and replace the vibrating
operating accessories. components.
3. Improperly operating vibration 3. Inspect/replace the vibration damper.
damper.
4. Improperly operating viscous 4. Inspect/replace the fan drive.
fan drive.
5. Worn or damaged generator 5. Check/replace the generator.
bearing.
6. Flywheel housing misaligned. 6. Check/correct flywheel alignment.
7. Loose or broken power 7. Inspect the crankshaft and rods for
component. damage that causes an unbalance.
Repair/replace as required.
8. Worn or unbalanced driveline 8. Check/repair driveline components.
components.

EXCESSIVE ENGINE 1. Drive belt squeal, insufficient 1. Check the automatic tensioner and
NOISES tension or abnormally high inspect the drive belt. Make sure water
loading. pump, tensioner pulley, fan hub and
generator turn freely.
2. Intake air or exhaust leaks. 2. Refer to Excessive Exhaust smoke
(Engine Diagnosis Performance).
3. Turbocharger noise. 3. Check turbocharger impeller and turbine
wheel for housing contact. Repair/replace as
required.
4. Gear train noise. 4. Visually inspect and measure gear
backlash. Replace gears as required.
5. Power function knock. 5. Check/replace rod and main bearings.

GENERATOR NOT 1. Loose or corroded battery. 1. Clean/tighten battery connection.

CHARGING OR
2. Generator belt slipping. 2. Check/replace automatic abelt tensioner.
INSUFFICIENT CHARGING
Check/replace and adjust belt.
3. Generator pulley loose on shaft. 3. Tighten pulley
4. Improperly operating generator. 4. Check/replace generator.
WJ ENGINE 9 - 11
DIAGNOSIS AND TESTING (Continued)

TAPPET NOISE VALVE CLEANING

(1) To determine source of tappet noise, operate (1) Clean all carbon deposits from the combustion
engine at idle with cylinder head covers removed. chambers, valve ports, valve stems, valve stem
(2) Feel each valve spring or rocker arm to detect guides and head.
noisy tappet. The noisy tappet will cause the affected (2) Clean all grime and gasket material from the
spring and/or rocker arm to vibrate or feel rough in engine cylinder head machined gasket surface.
operation.
INSPECTION
NOTE: Worn valve guides or cocked springs are (1) Inspect for cracks in the combustion chambers
sometimes mistaken for noisy tappets. If such is and valve ports.
the case, noise may be dampened by applying side (2) Inspect for cracks on the exhaust seat.
thrust on the valve spring. If noise is not apprecia- (3) Inspect for cracks in the gasket surface at each
bly reduced, it can be assumed the noise is in the coolant passage.
tappet. Inspect the rocker arm push rod sockets (4) Inspect valves for burned, cracked or warped
and push rod ends for wear. heads.
(5) Inspect for scuffed or bent valve stems.
(3) Valve tappet noise ranges from light noise to a (6) Replace valves displaying any damage.
heavy click. A light noise is usually caused by exces- (7) Check valve spring height (Fig. 2).
sive leak down around the unit plunger or by the
plunger partially sticking in the tappet body cylinder.
The tappet should be replaced. A heavy click is
caused by a tappet check valve not seating or by for-
eign particles becoming wedged between the plunger
and the tappet body. This will cause the plunger to
stick in the down position. This heavy click will be
accompanied by excessive clearance between the
valve stem and rocker arm as valve closes. In either
case, tappet assembly should be removed for inspec-
tion and cleaning.
The valve train generates a noise very much like a
light tappet noise during normal operation. Care
must be taken to ensure that tappets are making the
noise. In general, if more than one tappet seems to
be noisy, its probably not the tappets.

LOAD Kg HEIGHT mm STATE

SERVICE PROCEDURES
P1 0.00 H1 44.65 FREE LENGTH
P2 32-36 H2 38.60 VALVE CLOSED
VALVE SERVICE
P3 89-96 H3 28.20 VALVE OPEN
This procedure is done with the engine cylinder
head removed from the block.
Fig. 2 Valve Spring Chart
DISASSEMBLY
(1) Remove the engine cylinder head from the cyl- VALVE REFACING
inder block. Refer to cylinder head removal and (1) Use a valve refacing machine to reface the
installation in this section. intake and exhaust valves to the specified angle.
(2) Use Valve Spring Compressor Tool and com- (2) After refacing, a margin of at least 4.52-4.49
press each valve spring. mm (.178-.177 inch) must remain (Fig. 3). If the mar-
(3) Remove the valve locks, retainers, and springs. gin is less than 4.49 mm (.177 inch), the valve must
(4) Use an Arkansas smooth stone or a jewelers be replaced.
file to remove any burrs on the top of the valve stem,
especially around the groove for the locks.
(5) Remove the valves, and place them in a rack in
the same order as removed.
9 - 12 ENGINE WJ
SERVICE PROCEDURES (Continued)
VALVE STAND DOWN
Valve stand down is to maintain the adequate com-
pression ratio.
(1) Invert cylinder head.
(2) Fit each valve to its respective valve guide.
(3) Using a straight edge and feeler gauge (Fig. 4),
check valve head stand down: Inlet valve head stand
down 1.08 to 1.34 mm (.042 to.052 ins.) and exhaust
valve stand down.99 to 1.25 mm (.035 to.049
(3) ins.).
(4) If valve head stand down is not in accordance
with above, discard original valves, check stand down
with new valves and recut valve seat inserts to
obtain correct stand down.

Fig. 4 Checking Valve Stand Down

VALVE GUIDES
(1) Valve Guides height requirement.
(2) Measurement A (Fig. 5): 13.50 - 14.00 mm.

MEASUREMENT INTAKE EXHAUST

A 7.940-7.960 7.922-7.940
B 8.00-8.015 8.000-8.015
C 1.08-1.34 0.990-1.250
D 2.2 6 0.08 +0.07
2.09 −0.09

E 1.80-2.20 1.65-2.05
F 2.73-3.44 2.45-3.02
G 41.962-41.985 35.964-35.987 Fig. 5 Valve Guide Height
H 42.070-42.086 36.050-36.066
I 7.14-7.19 7.00-7.05 VALVE STEM-TO-GUIDE CLEARANCE
L 3.11-3.26 3.10-3.25
MEASUREMENT
Fig. 3 Valve Specification (1) Measure and record internal diameter of valve
VALVE SEAT REFACING guides. Valve guide internal diameter is 8.0 to 8.015
(1) Install a pilot of the correct size in the valve mm (.3149 to.3155 ins.).
guide bore. Reface the valve seat to the specified (2) Measure valve stems and record diameters.
angle with a good dressing stone. Remove only Intake valve stem diameter 7.94 to 7.96 mm (.3125
enough metal to provide a smooth finish. to.3133 in). Exhaust valve stem diameter 7.92 to 7.94
(2) Use tapered stones to obtain the specified seat mm (.3118 to.31215 in).
width when required.
WJ ENGINE 9 - 13
SERVICE PROCEDURES (Continued)
(3) Subtract diameter of valve stem from internal (8) Remove the lower radiator hose from the radi-
diameter of its respective valve guide to obtain valve ator (Fig. 6).
stem clearance in valve guide. Clearance of inlet (9) Remove the lower fan shroud retaining bolts
valve stem in valve guide is.040 to.075 mm (.0015 (Fig. 6).
to.0029 in). Clearance of exhaust valve stem in valve (10) Remove the exhaust system inlet pipe retain-
guide is.060 to.093 mm (.0023 to.0036 in). ing bolts from the turbocharger (Fig. 7).
(4) If valve stem clearance in valve guide exceeds
tolerances, new valve guides must be installed.

REMOVAL AND INSTALLATION

3.1L TURBO DIESEL ENGINE
REMOVAL
(1) Disconnect the negative battery cable.
(2) Disconnect the engine compartment lamp.
(3) Remove the hood. Refer to Group 23, Body for
the procedure.

WARNING: DO NOT LOOSEN THE RADIATOR VENT

OR DRAINCOCK WITH THE SYSTEM HOT AND
PRESSURIZED. SERIOUS BURNS FROM COOLANT
CAN OCCUR.

(4) Open the cooling system vent located on top of

the radiator.
(5) Raise the vehicle on the hoist
(6) Drain the cooling system. Refer to Group 7,
Cooling System for the procedure. Fig. 7 Exhaust System Inlet Pipe
(7) Remove the transmission fluid cooler lines from 1 – EXHAUST SYSTEM INLET PIPE RETAINING BOLTS
the radiator (Fig. 6). 2 – ENGINE OIL PAN

(11) Remove the nut retaining the wire harnesses

on the left engine mount.
(12) Lower the vehicle on the hoist.
(13) Remove the right and left headlamp assem-
blies from the vehicle. Refer to Group 8L, Lamps for
the procedure.
(14) Remove the front fascia. Refer to Group 13,
Frame and Bumpers for the procedure.
(15) Disconnect the ambient temperature sensor
and unclip the wire harness from the headlamp mod-
ule mounting assembly.
(16) Disconnect the right and left headlamp mod-
ule wire harnesses at the 10-way connectors located
just above the front bumper to the right and left of
the A/C condenser.
(17) Remove the headlamp module mounting
(HMM) assembly. Refer to Group 23, Body for the
Fig. 6 Transmission Fluid Cooler Lines procedure.
1 – TRANSMISSION FLUID COOLER LINES
(18) Remove the hood latch. Refer to Group 23,
2 – FAN SHROUD
3 – LOWER RADIATOR HOSE
Body for the procedure.
4 – FRONT SPLASH SHIELD (19) Remove the upper fan shroud retaining bolts.
5 – LOWER FAN SHROUD RETAINING BOLTS (20) Remove the radiator crossmember from the
vehicle.
9 - 14 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(21) Remove the manual cooling fan and let set
inside of the fan shroud.
(22) Remove the intercooler inlet and outlet hoses
from the vehicle (Fig. 8).

Fig. 9 Air Intake Hoses

1 – BREATHER HOSE
2 – INTERCOOLER INLET HOSE
3 – FRESH AIR INLET TUBE
Fig. 8 Intercooler Hoses 4 – AIR FILTER COVER
1 – INTERCOOLER INLET HOSE
2 – COOLANT RECOVERY HOSE
3 – REFRIGERANT LINE SUPPORT BRACKET (31) Remove the fan shroud and both cooling fans
4 – INTERCOOLER OUTLET HOSE as an assembly from the vehicle.
5 – FAN SHROUD
NOTE: The cooling module assembly includes the
radiator, intercooler and A/C condenser.
(23) Disconnect the breather hose and remove the
fresh air inlet tube from the vehicle (Fig. 9). (32) Remove the cooling module assembly retain-
(24) Remove the radiator overflow hose from the ing bolts and remove the cooling module from the
radiator vehicle.
(25) Remove the upper radiator hose from the (33) Remove the coolant reservoir supply hose
vehicle. from the engine.
(26) Disconnect the electric radiator cooling fan (34) Remove the coolant recovery hose from the
electrical connector. water manifold.
(27) Recover the refrigerant. Refer to Group 24, (35) Remove the EGR valve vacuum supply line
Heating and Air Conditioning for the procedure. from the valve (Fig. 11).
(28) Remove the intake air duct from the vehicle (36) Remove the heater core coolant supply lines
(Fig. 10). from the engine assembly (Fig. 11).
(29) Remove the power steering cooler retaining (37) Remove the refrigerant line from the A/C
bolts (Fig. 10) and position the cooler aside. accumulator assembly.
(30) Remove the suction and discharge lines from (38) Disconnect the oil pressure and boost pressure
the condenser assembly (Fig. 10). sensor electrical connectors and unclip wire harness
from the coolant supply lines.
WJ ENGINE 9 - 15
REMOVAL AND INSTALLATION (Continued)

Fig. 11 Engine Compartment View - Rightside

1 – HEATER CORE COOLANT SUPPLY HOSES
Fig. 10 Cooling Module Assembly
2 – EGR VALVE/COOLANT SUPPLY LINE BRACKET RETAINING
1 – INTAKE AIR DUCT BOLTS
2 – RADIATOR 3 – EGR VALVE VACUUM SUPPLY LINE
3 – COOLING SYSTEM VENT 4 – WIRE HARNESS RETAINING CLIPS
4 – POWER STEERING FLUID COOLER
5 – POWER STEERING COOLER RETAINING BOLTS
6 – A/C CONDENSER
7 – REFRIGERANT LINE RETAINING NUTS
8 – 10–WAY HEADLAMP MODULE CONNECTOR
9 – INTERCOOLER
10 – A/C CONDENSER RETAINING BOLTS

(39) Disconnect the engine ground. Located just

behind the oil filter.
(40) Remove the refrigerant line retaining nut
from the bulkhead and remove the refrigerant liquid
line from the vehicle.
(41) Cut the tiestraps retaining the wire harness
to the refrigerant line. Located above the compressor
assembly.
(42) Remove the refrigerant line support bracket
bolt from the cylinder head cover.
(43) Remove both of the refrigerant line retaining
bolts from the compressor and remove the lines from
the vehicle.
(44) Remove the power steering fluid supply hose
from the pump (Fig. 12).
(45) Remove the power steering fluid pressure line
from the pump (Fig. 12). Fig. 12 Power Steering Fluid Lines At Pump
(46) Remove the vacuum supply hose from the 1 – POWER STEERING PUMP
2 – POWER STEERING FLUID SUPPLY HOSE
engine mounted steel vacuum source line.
3 – POWER STEERING FLUID PRESSURE LINE
(47) Disconnect the generator field wire connector 4 – POWER STEERING PUMP PULLEY
from the rear of the generator. 5 – POWER STEERING PUMP PULLEY RETAINING BOLTS
(48) Unclip the battery feed wire cover and remove
the wire from the top of the generator.
9 - 16 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(49) Disconnect the speed control servo vacuum
supply hose from the engine mounted steel vacuum
source line.
(50) Disconnect the fuel supply and return hoses
from the engine assembly.
(51) Remove the wire harness mounting bracket
retaining nuts from the left engine mount (Fig. 13).

Fig. 14 Transmission Dipstick Tube Support Bracket

1 – TRANSMISSION DIPSTICK TUBE
2 – TURBOCHARGER EXHAUST MANIFOLD HEATSHIELD
3 – TRANSMISSION DIPSTICK TUBE SUPPORT BRACKET
RETAINING NUT

Fig. 13 Wire Harness Mounting Bracket

1 – FUEL FILTER
2 – WIRE HARNESS MOUNTING BRACKET RETAINING NUTS
3 – GENERATOR

(52) Disconnect the black and gray 10–way electri-

cal connectors from the engine wire harness.
(53) Disconnect the A/C compressor clutch and
glow plug harness electrical connectors.
(54) Remove the transmission dipstick tube sup-
port bracket retaining nut from the turbocharger
heatshield (Fig. 14).
(55) Raise the vehicle on the hoist.
(56) Disconnect the starter motor electrical.
(57) Remove the starter motor retaining bolts and
remove the starter from the vehicle (Fig. 15).

NOTE: Mark the position of the torque convertor in

relation to the flexplate through the starter motor
access hole. This reference mark will be used to
line up the two components for reassemble.
Fig. 15 Starter Motor Position & Orientation
1 – STARTER MOTOR RETAINING BOLTS (2 OF 3)
2 – TRANSMISSION FLUID COOLER LINES
3 – TRANSMISSION
4 – ENGINE OIL PAN
5 – STARTER MOTOR
WJ ENGINE 9 - 17
REMOVAL AND INSTALLATION (Continued)
(58) Working through the torque convertor bolt
access hole (Fig. 16), Rotate the engine to access and
remove the (4) torque convertor to flexplate retaining
bolts.

Fig. 17 Transmission Support Crossmember

1 – TRANSFER CASE
2 – TRANSMISSION MOUNT RETAINING BOLTS (2 OF 4)
3 – EXHAUST SYSTEM SUPPORT BRACKET RETAINING BOLTS
4 – CROSSMEMBER RETAINING BOLTS
5 – TRANSMISSION
Fig. 16 Torque Convertor Bolt Access Hole 6 – CROSSMEMBER RETAINING BOLTS
1 – TORQUE CONVERTER BOLT ACCESS HOLE
2 – ENGINE OIL PAN
3 – TOP DEAD CENTER ALIGNMENT TOOL ACCESS HOLE

(59) Disconnect the engine ground. Located to the

rear of the left engine mount.
(60) Remove the left engine mount throughbolt
nut. Do not remove the bolt at this time.
(61) Support the rear of the transmission assembly
with a jack.
(62) Remove the (8) transmission support cross-
member retaining bolts (Fig. 17).
(63) Lower the transmission and transfer case
assembly enough to gain access to the upper six
transmission bellhousing bolts.
(64) Remove the upper six bellhousing bolts.
(65) Raise the transmission assembly back into
position and temporarily install four of the eight
transmission crossmember retaining bolts. Install
two bolts on each side.
(66) Remove the remaining four bellhousing bolts. Fig. 18 Engine Mount Sill Plate Retaining Bolts -
(67) Partially lower the vehicle. Left Wheel Well
(68) Remove the engine mount sill plate retaining 1 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
bolts in the left wheel well (Fig. 18). 2 – LEFT FRONT TIRE
9 - 18 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(69) Remove the engine mount sill plate retaining
bolts in the right wheel well (Fig. 19).

Fig. 19 Engine Mount Sill Plate Retaining Bolts -

Right Wheel Well Fig. 20 Engine Mount Sill Plate Bolts - Leftside
1 – ENGINE MOUNT SILL PLATE RETAINING BOLTS 1 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
2 – RIGHT FRONT TIRE 2 – BATTERY

(70) Lower the vehicle to the ground.

(71) Support the front of the transmission with a
jack.
(72) Remove the left engine mount sill plate
retaining bolts (Fig. 20).
(73) Remove the right engine mount sill plate
retaining bolts (Fig. 21).
(74) Set up an engine lifting device and support
the weight of the engine assembly.

CAUTION: Before proceeding be certain the front of

the transmission is properly supported with a jack.

CAUTION: This engine is equipped with a engine

speed sensor located in the top of the bellhousing.
Care must be taken not to damage the sensor or
corresponding wires during engine removal and
installation.

(75) Using the engine lifting device, pull the

engine assembly away from the transmission approx-
imately three inches and stop.. Fig. 21 Engine Mount Sill Plate Bolts - Rightside
(76) Working between the bulkhead and the right 1 – TURBOCHARGER ASSEMBLY
rear of the engine assembly, disconnect the engine 2 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
speed sensor electrical connector. 3 – AIR FILTER ASSEMBLY
(77) Remove the left engine mount throughbolt
and remove the sill plate.
(78) With assistance from another person, care- One person operating the engine lifting device and
fully remove the engine assembly from the vehicle. the other facilitating the engine removal.
WJ ENGINE 9 - 19
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
CAUTION: This engine is equipped with a misfire
sensor. Located in the top of the bellhousing. Care
must be taken not to damage the sensor or corre-
sponding wires during engine removal and installa-
tion.

CAUTION: Be certain the torque convertor is prop-

erly installed in the transmission. If the torque con-
vertor is not installed all the way in the
transmission the engine will not rotate upon instal-
lation.

(1) With assistance from another person, carefully

install the engine assembly in the vehicle. One per-
son operating the engine lifting device and the other
facilitating the engine installation.
(2) Install the left engine mount sill plate and
throughbolt. Leave loose at this time.
(3) Working between the bulkhead and the right
rear of the engine assembly, connect the engine speed
Fig. 22 Engine Mount Sill Plate Bolts - Leftside
sensor electrical connector.
1 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
(4) Using the engine lifting device and/or the jack 2 – BATTERY
under the transmission, position the engine/transmis-
sion assembly so the engine block mounted dowel
pins are perfectly aligned with the corresponding
holes in the transmission bellhousing.

CAUTION: The engine block and transmission must

be in perfect alignment before attempting to install
the bellhousing bolts. Misalignment will cause the
aluminum bellhousing to be damaged.

(5) Install two engine to transmission bellhousing

retaining bolts. One on each side of the bellhousing.
(6) Make certain the engine mount sill plate bolt
holes are aligned with there corresponding weld nuts
in the frame rails.
(7) Remove the engine lifting device.
(8) Remove the jack from the transmission.
(9) Install the leftside engine mount sill plate
retaining bolts (Fig. 22). Leave bolts loose at this
time.
(10) Install the rightside engine mount sill plate
retaining bolts (Fig. 23). Leave bolts loose at this
time.
(11) Partially raise the vehicle on the hoist.
(12) Install the engine mount sill plate retaining Fig. 23 Engine Mount Sill Plate Bolts - Rightside
bolts in the right wheel well (Fig. 24). Leave bolts 1 – TURBOCHARGER ASSEMBLY
loose at this time. 2 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
(13) Install the engine mount sill plate retaining 3 – AIR FILTER ASSEMBLY
bolts in the left wheel well (Fig. 25). Torque the bolts
to 61 N·m (45 ft. lbs.). (15) Torque the left engine mount throughbolt to
(14) Torque all engine mount sill plate bolts to 61 61 N·m (45 ft. lbs.).
N·m (45 ft. lbs.). (16) Raise the vehicle on the hoist.
9 - 20 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(20) Lower the transmission and transfer case
assembly enough to gain access to the upper six bell-
housing bolts.

NOTE: Be certain all brackets that were originally

installed on the bellhousing bolts are reinstalled.
Cable misrouting could result.

(21) Install the upper six bellhousing bolts. Torque

the bolts to 102 N·m (75 ft. lbs.).
(22) Raise the transmission assembly back into
position and install the eight transmission crossmem-
ber retaining bolts (Fig. 26). Torque the bolts to 41
N·m (30 ft. lbs.).

Fig. 24 Engine Mount Sill Plate Bolts - Right Wheel

Well
1 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
2 – RIGHT FRONT TIRE

Fig. 26 Transmission Support Crossmember

1 – TRANSFER CASE
2 – TRANSMISSION MOUNT RETAINING BOLTS (2 OF 4)
3 – EXHAUST SYSTEM SUPPORT BRACKET RETAINING BOLTS
4 – CROSSMEMBER RETAINING BOLTS
5 – TRANSMISSION
6 – CROSSMEMBER RETAINING BOLTS

NOTE: Be certain the torque convertor is properly

Fig. 25 Engine Mount Sill Plate Bolts - Left Wheel aligned with the flexplate before attempting to
Well installing the retaining bolts.
1 – ENGINE MOUNT SILL PLATE RETAINING BOLTS
2 – LEFT FRONT TIRE
NOTE: When installing the torque convertor to flex-
plate retaining bolts, the torque convertor can be
(17) Install the remaining lower bellhousing bolts. rotated into position with a flat-bladed screwdriver
Torque all the bolts to 102 N·m (75 ft. lbs.). through the starter motor access hole. Then work-
(18) Support the rear of the transmission with a ing through the torque convertor bolt access hole,
jack. thread a longer than original bolt into the convertor
(19) Remove the (4) temporarily installed trans- and pull the convertor up against the flexplate by
mission crossmember bolts. hand. Remove the longer bolt and install the origi-
nal bolts one by one until all bolts are installed.
Then go back and torque all bolts to specification.
WJ ENGINE 9 - 21
REMOVAL AND INSTALLATION (Continued)
(23) Rotate the engine assembly to access and
install the (4) torque convertor to flexplate retaining
bolts. Torque the bolts to 75 N·m (55 ft. lbs.).
(24) Install the wire harness support bracket on
the left engine mount.
(25) Install the exhaust system inlet pipe on the
turbocharger (Fig. 27). Torque the bolts to 41 N·m
(30 ft. lbs.).

Fig. 28 Transmission Dipstick Tube Support Bracket

1 – TRANSMISSION DIPSTICK TUBE
2 – TURBOCHARGER EXHAUST MANIFOLD HEATSHIELD
3 – TRANSMISSION DIPSTICK TUBE SUPPORT BRACKET
RETAINING NUT

Fig. 27 Exhaust System Inlet Pipe

1 – EXHAUST SYSTEM INLET PIPE RETAINING BOLTS
2 – ENGINE OIL PAN

(26) Lower the vehicle on the hoist.

(27) Install the transmission dipstick tube support
bracket retaining nut on the turbocharger heatshield
(Fig. 28). Torque the nut to 25 N·m (221 in. lbs.).
(28) Connect the A/C compressor clutch and glow
plug harness electrical connectors.
(29) Connect the black and gray 10–way electrical
connectors and clip connectors on the wire harness
mounting bracket.
(30) Install the wire harness mounting bracket
and retaining nuts on the left engine mount (Fig. 29).
Torque the nuts to 25 N·m (221 in. lbs.).
(31) Connect the fuel supply and return hoses on
the engine assembly.
(32) Connect the speed control servo vacuum supply
hose on the engine mounted steel vacuum source line. Fig. 29 Wire Harness Mounting Bracket
(33) Install the battery feed wire on the top of the 1 – FUEL FILTER
generator and install the cover. 2 – WIRE HARNESS MOUNTING BRACKET RETAINING NUTS
(34) Connect the generator field wire connector on 3 – GENERATOR
the rear of the generator.
(35) Install the vacuum supply hose on the engine
mounted steel vacuum source line.
9 - 22 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(36) Install the power steering fluid pressure line (45) Install the heater core coolant supply hoses on
on the pump (Fig. 30). Be certain the sealing 0-ring the engine (Fig. 31).
is well lubricated and free of tears.
(37) Install the power steering fluid supply hose on
the pump (Fig. 30).

Fig. 31 Engine Compartment View - Rightside

1 – HEATER CORE COOLANT SUPPLY HOSES
2 – EGR VALVE/COOLANT SUPPLY LINE BRACKET RETAINING
BOLTS
3 – EGR VALVE VACUUM SUPPLY LINE
Fig. 30 Power Steering Fluid Lines At Pump 4 – WIRE HARNESS RETAINING CLIPS
1 – POWER STEERING PUMP
2 – POWER STEERING FLUID SUPPLY HOSE
3 – POWER STEERING FLUID PRESSURE LINE
(46) Install the EGR valve vacuum supply line on
4 – POWER STEERING PUMP PULLEY the valve (Fig. 31).
5 – POWER STEERING PUMP PULLEY RETAINING BOLTS (47) Install the coolant recovery hose on the water
manifold.
(48) Install the coolant reservoir supply hose on
(38) Install both of the refrigerant lines on the A/C the engine.
compressor. Torque the retaining bolts to 28 N·m (21 (49) Install the cooling module assembly and
ft. lbs.). Be certain the sealing gaskets are well lubri- retaining bolts (Fig. 32). Torque the bolts to 41 N·m
cated and free of tears. (30 ft. lbs.).
(39) Install the refrigerant line support bracket (50) Install the fan shroud and both cooling fans
and bolt on the cylinder head cover. as an assembly on the vehicle.
(40) Install the tiestraps retaining the wire har- (51) Install the suction and discharge refrigerant
ness on the low side refrigerant line. lines on the condenser assembly (Fig. 32). Torque the
(41) Install the refrigerant liquid line. Torque the retaining nuts to 28 N·m (21 ft. lbs.). Be certain the
retaining nut on the bulkhead to 28 N·m (21 ft. lbs.). sealing gaskets are well lubricated and free of tears.
Be certain the sealing gasket is well lubricated and (52) Position the power steering cooler and install
free of tears. the retaining bolts (Fig. 32).
(42) Connect the engine ground. Located just (53) Charge the refrigerant system. Refer to Group
behind the oil filter. 24, Heating and Air Conditioning for the procedure.
(43) Connect the oil pressure and boost pressure (54) Connect the electric radiator cooling fan elec-
sensor electrical connectors and clip the wire harness trical connector.
on the coolant supply tubes. (55) Install the intake air duct on the vehicle (Fig.
(44) Install the low side refrigerant line on the A/C 32).
accumulator assembly. Torque the nut to 28 N·m (21 (56) Install the upper radiator hose on the vehicle.
ft. lbs.). Be certain the sealing gasket is well lubri- (57) Install the radiator overflow hose on the radi-
cated and free of tears. ator
WJ ENGINE 9 - 23
REMOVAL AND INSTALLATION (Continued)

Fig. 32 Cooling Module Assembly Fig. 33 Air Intake Hoses

1 – INTAKE AIR DUCT 1 – BREATHER HOSE
2 – RADIATOR 2 – INTERCOOLER INLET HOSE
3 – COOLING SYSTEM VENT 3 – FRESH AIR INLET TUBE
4 – POWER STEERING FLUID COOLER 4 – AIR FILTER COVER
5 – POWER STEERING COOLER RETAINING BOLTS
6 – A/C CONDENSER
7 – REFRIGERANT LINE RETAINING NUTS
8 – 10–WAY HEADLAMP MODULE CONNECTOR
9 – INTERCOOLER
10 – A/C CONDENSER RETAINING BOLTS

(58) Connect the breather hose and install the

fresh air inlet tube on the engine (Fig. 33).
(59) Install the intercooler inlet and outlet hoses
on the engine (Fig. 34).
(60) Install the manual cooling fan on the engine.
(61) Install the radiator crossmember on the vehi-
cle. Refer to Group 23, Body for the procedure.
(62) Install the upper fan shroud retaining bolts.
Torque the bolts to 15 N·m (132 in. lbs.).
(63) Install the hood latch support brackets and
the hood latch on the vehicle.
(64) Install the headlamp module mounting
(HMM) assembly. Refer to Group 23, Body for the
procedure.
(65) Connect the right and left headlamp module
wire harnesses at the 10-way connectors. Located
just above the front bumper to the right and left of
Fig. 34 Intercooler Hoses
1 – INTERCOOLER INLET HOSE
the a/c condenser.
2 – COOLANT RECOVERY HOSE
(66) Connect the ambient temperature sensor and 3 – REFRIGERANT LINE SUPPORT BRACKET
clip the wire harness on the headlamp module 4 – INTERCOOLER OUTLET HOSE
mounting assembly. 5 – FAN SHROUD
(67) Install the front fascia. Refer to Group 13,
Frame and Bumpers for the procedure.
9 - 24 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(68) Install the right and left headlamp assemblies EXHAUST AND INTAKE MANIFOLD
on the vehicle. Refer to Group 8L, Lamps for the pro-
cedure. REMOVAL
(69) Raise the vehicle on the hoist.
(70) Connect the engine ground. Located to the NOTE: Both the intake and exhaust manifolds must
rear of the left engine mount. be removed due to a single sealing gasket for both
(71) Install the starter motor. Torque the retaining manifolds.
bolts to 24 N·m (212 in. lbs.).
(72) Connect the starter motor electrical. Torque (1) Disconnect the negative battery cable.
the B+ nut to 8 N·m. (2) Raise the vehicle on a hoist.
(73) Install the lower fan shroud retaining bolts
(Fig. 35). Torque the bolts to 15 N·m (132 in. lbs.). WARNING: DO NOT LOOSEN THE RADIATOR VENT
(74) Install the lower radiator hose on the radiator OR DRAINCOCK WITH THE SYSTEM HOT AND
(Fig. 35). PRESSURIZED. SERIOUS BURNS FROM COOLANT
CAN OCCUR.

(3) Drain the cooling system. Refer to Group 7,

Cooling System for procedure.
(4) Remove the exhaust system inlet pipe retaining
bolts (Fig. 36).

Fig. 35 Transmission Fluid Cooler Lines

1 – TRANSMISSION FLUID COOLER LINES
2 – FAN SHROUD
3 – LOWER RADIATOR HOSE
4 – FRONT SPLASH SHIELD
5 – LOWER FAN SHROUD RETAINING BOLTS

(75) Install the transmission fluid cooler lines on

the radiator (Fig. 35).
(76) Lower the vehicle on the hoist.
(77) Fill the cooling system and close the system Fig. 36 Exhaust System Inlet Pipe Retaining Bolts
vent. Refer to Group 7, Cooling System for the proce- 1 – EXHAUST SYSTEM INLET PIPE RETAINING BOLTS
dure. 2 – ENGINE OIL PAN
(78) Install the hood. Refer to Group 23, Body for
procedure.
(5) Disconnect the turbocharger oil return hose
(79) Fill the power steering system fluid. Refer to
from the turbocharger.
Group 19, Steering – Power Steering Pump-Initial
(6) Lower the vehicle on the hoist.
operation for the procedure.
(7) Remove the intercooler inlet hose from the
(80) Fill the transmission fluid. Refer to Group 21,
vehicle (Fig. 37).
Transmission and Transfer Case for the procedure.
(8) Disconnect the breather hose from the fresh air
(81) Connect the negative battery cable.
inlet tube (Fig. 37).
(82) Check the engine oil level before engine start
(9) Unclip the air filter cover and remove the fresh
up.
air inlet tube from the turbocharger (Fig. 37).
Remove the assembly from the vehicle.
WJ ENGINE 9 - 25
REMOVAL AND INSTALLATION (Continued)

Fig. 38 Engine Compartment

1 – HEATER CORE COOLANT SUPPLY HOSES
Fig. 37 Air Intake Hoses
2 – EGR VALVE/COOLANT SUPPLY LINE BRACKET RETAINING
1 – BREATHER HOSE BOLTS
2 – INTERCOOLER INLET HOSE 3 – EGR VALVE VACUUM SUPPLY LINE
3 – FRESH AIR INLET TUBE 4 – WIRE HARNESS RETAINING CLIPS
4 – AIR FILTER COVER

(10) Remove the EGR vacuum supply hose from

the EGR valve (Fig. 38).
(11) Disconnect the heater core coolant supply
lines from the engine assembly (Fig. 38).
(12) Unclip the wire harness from the coolant sup-
ply lines (Fig. 38).
(13) Remove the (2) EGR valve / coolant supply
line retaining bolts (Fig. 38).
(14) Remove the coolant supply line support
bracket bolt from the water pump housing.
(15) Disconnect the two remaining hoses and
remove the coolant lines from the vehicle.
(16) Remove the oil separator retaining bolts.
(17) Disconnect the crankcase vapor supply and
return hoses and remove the oil separator from the
vehicle.
(18) Remove the transmission dipstick tube sup-
port bracket nut from the turbocharger heatshield
(Fig. 39).
(19) Remove the exhaust manifold / turbocharger
heatshield retaining bolts and remove the heatshield
from the vehicle. Fig. 39 Transmission Dipstick Tube Support Bracket
(20) Pull back the EGR tube heatshield to access 1 – TRANSMISSION DIPSTICK TUBE
and remove the EGR tube nut from the exhaust 2 – TURBOCHARGER EXHAUST MANIFOLD HEATSHIELD
manifold. Remove the EGR valve and tube assembly 3 – TRANSMISSION DIPSTICK TUBE SUPPORT BRACKET
from the vehicle. RETAINING NUT
(21) Remove the oil pressure supply line banjo bolt
from the turbocharger.
9 - 26 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 40 Exhaust Manifold/Turbocharger Heatshield

1 – EXHAUST MANIFOLD/TURBOCHARGER HEATSHIELD
2 – HEATSHIELD RETAINING BOLTS
3 – HEATER CORE SUPPLY/RETURN LINES Fig. 41 Intake and Exhaust Manifold
4 – OIL FILTER HOUSING 1 – WATER MANIFOLD
5 – ENGINE OIL COOLER 2 – INTAKE MANIFOLD ELBOW
6 – TURBOCHARGER 3 – BOOST PRESSURE SENSOR
4 – INTAKE MANIFOLD
5 – INTAKE/EXHAUST MANIFOLD GASKET
(22) Position a drain pan under the transmission. 6 – TURBOCHARGER OIL RETURN LINE
(23) Remove the transmission dipstick tube from 7 – EXHAUST MANIFOLD
the transmission oil pan by pulling straight up. Posi- 8 – CYLINDER HEAD
tion the tube assembly out of the way to allow for
manifold / turbocharger removal.
(29) Remove the intake manifold retaining bolts
(24) Remove the exhaust manifold retaining nuts
and remove the intake manifold from the vehicle
and remove the manifold and turbocharger assembly
(Fig. 41).
from the vehicle (Fig. 41).
(30) Remove the intake/exhaust manifold gasket
NOTE: If only servicing the intake manifold the fol- from the manifolds mounting studs.
lowing two steps are not required.
CLEANING
(25) Place the assembly in a vice. All old gaskets should be inspected for any tears or
(26) Remove the (4) turbocharger to exhaust man- signs of prior leakage. If any gaskets show such indi-
ifold retaining nuts and separate. cations, they should be replaced with new gaskets.
(27) Remove the (4) intake air duct retaining bolts All gasket mating surfaces must be cleaned of old
from the intake manifold. gasket material to produce a smooth and dirt/oil free
(28) Remove the remaining bolts from the intake sealing surface for the new gasket.
air duct and position the duct and hose assembly out
of the way.
WJ ENGINE 9 - 27
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Position the new intake/exhaust manifold gas-
ket on the manifolds mounting studs.
(2) Install the intake manifold and install the
retaining nuts (Fig. 41). Torque the nuts to 32 N·m
(23 ft. lbs.).
(3) Position the new intake air duct gasket.
(4) Install the intake air duct on the engine.
Torque the bolts to 32 N·m (23 ft. lbs.).

NOTE: If only servicing the intake manifold the fol-

lowing two steps are not required.

(5) Position the gasket and install the turbo on the

exhaust manifold. Torque the nuts to 32 N·m (23 ft.
lbs.).
(6) Remove the assembly from the vice and posi-
tion on the exhaust manifold mounting studs.
(7) Install the exhaust manifold retaining nuts and
torque to 32 N·m (23 ft. lbs.) (Fig. 41).
(8) Install the transmission dipstick tube in the
transmission case.
(9) Remove the drain pan. Fig. 42 Transmission Dipstick Tube Support Bracket
(10) Install the oil pressure supply line on turbo- 1 – TRANSMISSION DIPSTICK TUBE
charger. Torque the banjo bolt fitting to 27 N·m (20 2 – TURBOCHARGER EXHAUST MANIFOLD HEATSHIELD
ft. lbs.). Be certain the copper sealing washers are 3 – TRANSMISSION DIPSTICK TUBE SUPPORT BRACKET
RETAINING NUT
installed. One on the top and bottom of the supply
line.
(11) Install the EGR tube nut on the exhaust man-
ifold and temporarily install one of the EGR valve
retaining bolts. Be certain the EGR valve gasket is in
place.
(12) Torque the EGR tube retaining nut to 34 N·m
(25 ft.lbs.). Remove the temporarily installed EGR
valve bolt
(13) Install the exhaust manifold heatshield (Fig.
40). Torque bolts to 11 N·m (97 in. lbs.).
(14) Install the transmission dipstick tube support
bracket retaining nut on the turbocharger heatshield
(Fig. 42). Torque the nut to 20 N·m (177 in. lbs.).
(15) Install the front (front of engine) heater core
coolant supply hoses on the coolant line assembly
and install the line assembly on the engine. Torque
the (3) retaining bolts to 27 N·m (20 ft. lbs.) (Fig. 43).
(16) Connect the crankcase vapor supply and
return hoses on the oil separator.
(17) Install the oil separator retaining bolts.
(18) Install the heater core coolant supply hoses on
the coolant line assembly (Fig. 43).
(19) Clip the wire harness on the coolant supply
Fig. 43 Diesel Engine Compartment
1 – HEATER CORE COOLANT SUPPLY HOSES
lines (Fig. 43).
2 – EGR VALVE/COOLANT SUPPLY LINE BRACKET RETAINING
(20) Install the EGR vacuum supply hose on the BOLTS
EGR valve. 3 – EGR VALVE VACUUM SUPPLY LINE
4 – WIRE HARNESS RETAINING CLIPS
9 - 28 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(21) Install the fresh air inlet tube assembly on
the turbocharger. Clip the air filter cover in position
and connect the breather hose (Fig. 44).

Fig. 45 Exhaust System Inlet Pipe Retaining Bolts

1 – EXHAUST SYSTEM INLET PIPE RETAINING BOLTS
2 – ENGINE OIL PAN

Fig. 44 Air Intake Hoses

1 – BREATHER HOSE (5) Remove the low pressure refrigerant line
2 – INTERCOOLER INLET HOSE retaining bolt and remove the line from the compres-
3 – FRESH AIR INLET TUBE sor. Cover both openings.
4 – AIR FILTER COVER (6) Remove the left engine mount throughbolt nut.
Do not remove the bolt at this time.
(22) Install the intercooler inlet hose on the vehi- (7) Lower the vehicle on the hoist.
cle (Fig. 44). (8) Remove the intake manifold elbow inlet hose
(23) Raise the vehicle on the hoist. (Fig. 46).
(24) Install the turbocharger oil return hose on the (9) Remove the intake manifold elbow (Fig. 46).
turbocharger. (10) Remove the refrigerant line support bracket
(25) Install the exhaust system inlet pipe on the retaining bolt from the cylinder head cover and posi-
turbocharger (Fig. 45). Torque the bolts to 22 N·m tion the refrigerant line out of the way.
(194 in. lbs.). (11) Disconnect the (5) glow plug electrical connec-
(26) Lower the vehicle on the hoist. tors and position the wire harness out of the way.
(27) Fill the cooling system. Refer to Group 7, (12) Remove the Crankcase breather hose from the
Cooling System for procedure. front of the cylinder head cover.
(28) Check the transmission fluid level and top off (13) Remove the cylinder head cover retaining
if necessary. bolts (Fig. 47) (Fig. 48).
(29) Connect the negative battery cable. (14) Remove the fuel filter / water separator
(30) Start the engine and check for leaks. retaining nuts and position the filter assembly out of
the way.
CYLINDER HEAD COVER (15) Position a jack under the oil pan. Make sure
to place a piece of wood between the jack and the oil
REMOVAL pan.
(1) Disconnect the negative battery cable. (16) Slightly, raise the weight off of the left
(2) Recover the refrigerant system. Refer to Group engine mount until the left engine mount through-
24, Heating and Air Conditioning for the procedure. bolt can be removed.
(3) Raise the vehicle on the hoist. (17) Using the jack, lower the engine assembly
(4) Remove the front splash shield. until the cylinder head cover can be removed from
the vehicle.
WJ ENGINE 9 - 29
REMOVAL AND INSTALLATION (Continued)

Fig. 46 Intake Manifold Elbow

1 – INTAKE MANIFOLD ELBOW
2 – INTERCOOLER OUTLET HOSE
3 – GENERATOR
4 – UPPER RADIATOR HOSE
Fig. 47 Cylinder Head Cover
1 – WATER MANIFOLD RETAINING BOLTS
INSTALLATION 2 – WATER MANIFOLD
(1) Install the cylinder head cover and gasket. 3 – CYLINDER HEAD COVER
Torque the bolts to 15 N·m (133 in. lbs.) (Fig. 47) 4 – CYLINDER HEAD COVER RETAINING BOLTS
(Fig. 48).
(2) Using the jack, raise the engine assembly until
the left engine mount throughbolt can be installed. (15) Evacuate and charge the refrigerant system.
(3) Remove the jack and install the fuel filter / Refer to Group 24, Heater and Air Conditioning for
water separator. the procedure.
(4) Connect the crankcase breather hose to front of (16) Start the engine and check for leaks.
cylinder head cover.
WARNING: USE EXTREME CAUTION WHEN THE
(5) Connect the (5) glow plug electrical connectors
ENGINE IS OPERATING. DO NOT STAND IN DIRECT
(Fig. 47).
LINE WITH THE FAN. DO NOT PUT HANDS NEAR
(6) Position the refrigerant line and install the
THE PULLEYS, BELTS OR FAN. DO NOT WEAR
retaining bolt.
LOOSE CLOTHING.
(7) Install the intake manifold elbow (Fig. 46).
(8) Install the intake manifold elbow inlet hose
(Fig. 46). HYDRAULIC TAPPETS
(9) Raise the vehicle on the hoist.
(10) Install the left engine mount throughbolt nut. REMOVAL
Torque the nut to 61 N·m (45 ft. lbs.). (1) Disconnect the negative battery cable.
(11) Install the low pressure refrigerant line and (2) Discharge the air conditioning system. Refer to
retaining bolt. Torque the bolt to 28 N·m (21 ft. lbs.). Group 24, Heating and Air Conditioning for proce-
Be certain the sealing o-ring is well lubricated and dure.
free of tears. (3) Remove the A/C lines at the compressor and
(12) Install the front splash shield. cap.
(13) Lower the vehicle on the hoist. (4) Remove the A/C line bracket attached to the
(14) Connect the negative battery cable. cylinder head cover and move the lines away from
the cylinder head.
9 - 30 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 49 Tappet And Rocker Arm Assembly

Fig. 48 Cylinder Head Cover Removal

1 – CYLINDER HEAD COVER GASKET
2 – OIL FEED LINE RETAINING CLIP
3 – PUSH ROD
4 – ROCKER ARM ASSEMBLY
5 – ROCKER ARM OIL FEED LINE
6 – CYLINDER HEAD COVER

(5) Remove cylinder head cover. Refer to cylinder

head cover removal and installation procedure in this
section.
(6) Remove the rocker assemblies and push rods.
Refer to rocker arms and push rod removal and
installation procedure in this section. Identify push
rods to ensure installation in original location. Fig. 50 Tappet And Retainer
(7) Remove cylinder head, intake manifold, and 1 – TAPPET RETAINERS
exhaust manifold. Refer to cylinder head removal 2 – CYLINDER BLOCK
and installation in this section.
(8) Remove the tappet retainers (Fig. 50).
CAUTION: The plunger and tappet bodies are not
(9) Slide Hydraulic Tappet Remover/Installer Tool
interchangeable. The plunger and valve must
through opening in block and seat tool firmly in the
always be fitted to the original body. It is advisable
head of tappet.
to work on one tappet at a time to avoid mixing of
(10) Pull the tappet out of the bore with a twisting
parts. Mixed parts are not compatible. DO NOT dis-
motion. If all tappets are to be removed, identify tap-
assemble a tappet on a dirty work bench.
pets to ensure installation in original location.
WJ ENGINE 9 - 31
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Lubricate the tappets.
(2) Install the tappets and retainers in their origi-
nal positions. Ensure that the oil feed hole in the
side of the tappet body faces up (away from the
crankshaft).
(3) Install the cylinder head, intake manifold, and
exhaust manifold. Refer to cylinder head removal
and installation in this section.
(4) Install the push rods.
(5) Install the rocker arms. Refer to rocker arms
and push rod removal and installation in this section.
(6) Install the cylinder head cover. Refer to cylin-
der head cover removal and installation in this sec-
tion.
(7) Connect the negative battery cable.

CAUTION: To prevent damage to valve mechanism,

engine must not be run above fast idle until all
hydraulic tappets have filled with oil and have
become quiet.

(8) Start and operate engine. Warm up to normal Fig. 51 Rocker Arm Retaining Nut
operating temperature. 1 – ROCKER ARM ASSEMBLY
2 – ROCKER ARM RETAINING NUTS
ROCKER ARMS AND PUSH RODS 3 – ROCKER ARM SPRING PLATE

REMOVAL rocker arm assemblies. Follow the procedure below

(1) Disconnect the negative battery cable. to ensure that engine damage does not occur.
(2) Discharge the air conditioning system. Refer to
Group 24, Heating and Air Conditioning for proce- • Install the rocker arm assemblies in the same
dure. order as removed.
(3) Remove the service valves and cap the com- • Bring piston # 1 to Top Dead Center.
pressor ports. Refer to Group 24, Heating and Air • At this point tighten the rocker arm nuts for cyl-
Conditioning. inder # 2–3–4–5. Torque nuts to 27 N·m (20 ft. lbs.).
(4) Remove the cylinder head cover. Refer to cylin- • Slowly rotate the crankshaft 90° clockwise or
der head cover removal and installation in this sec- counterclockwise, then tighten the rocker arm nuts
tion. for cylinder # 1. Torque nuts to 27 N·m (20 ft. lbs.).
(5) Remove the rocker arm retaining nut (Fig. 51) (4) Install the cylinder head cover. Refer to cylinder
(Fig. 52). head cover removal and installation in this group.
(6) Remove the rocker assembly. Place them on a (5) Evacuate and charge the air conditioning sys-
bench in the same order as removed. tem. Refer to Group 24, Heater and Air Conditioning.
(7) Remove the push rods and place them on a (6) Connect the negative battery cable.
bench in the same order as removed.
VALVE SPRINGS
INSTALLATION This procedure can be done with the engine cylin-
(1) Rotate the crankshaft until the mark lines up der head installed on the block. Each valve spring is
with the TDC mark on the timing cover. held in place by a retainer and a set of conical valve
(2) Install the push rods in the same order as locks. The locks can be removed only by compressing
removed. the valve spring.

WARNING: During the installation of the rocker arm REMOVAL

assemblies it is possible to cause valve interfer- (1) Disconnect the negative battery cable.
ence between the piston and valve if the piston is (2) Remove the cylinder head cover. Refer to cylin-
near Top Dead Center (TDC). This is due to the slow der head cover removal and installation in this section.
bleed down rate of the tappets when adjusting the
9 - 32 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(7) Tap the retainer or tip with a rawhide hammer
to loosen the lock from the retainer. Use Valve Spring
Compressor Tool to compress the spring and remove
the locks.
(8) Remove the valve spring and retainer.
(9) Inspect the valve stems, especially the grooves.
An Arkansas smooth stone should be used to remove
nicks and high spots.

INSTALLATION
(1) Install the valve spring and retainer.
(2) Compress the valve spring with Valve Spring
Compressor Tool and insert the valve locks. Release
the spring tension and remove the tool. Tap the
spring from side-to-side to ensure that the spring is
seated properly on the engine cylinder head.
(3) Disconnect the air hose. Remove the adaptor
from the fuel injector hole and install the fuel injector.
(4) Repeat the procedures for each remaining valve
spring to be removed.
(5) Install the push rods. Ensure the bottom end of
each rod is centered in the plunger cap seat of the
hydraulic valve tappet.

WARNING: During the installation of the rocker arm

assemblies it is possible to cause valve interfer-
ence between the piston and valve if the piston is
near Top Dead Center (TDC). This is due to the slow
bleed down rate of the tappets when adjusting the
rocker arm assemblies. Follow the procedure below
Fig. 52 Rocker Arm Assemblies to ensure that engine damage does not occur.
1 – CYLINDER HEADS
2 – ROCKER ARM RETAINING NUTS • Install the rocker arm assemblies in the same
3 – ROCKER ARM SPRING PLATE order as removed.
4 – ROCKER ARM ASSEMBLIES • Bring piston # 1 to Top Dead Center.
• At this point tighten the rocker arm nuts for cyl-
(3) Remove the rocker arms assemblies and push inder # 2–3–4–5. Torque nuts to 27 N·m (20 ft. lbs.).
rods. Refer to rocker arm and push rod removal and • Slowly rotate the crankshaft 90° clockwise or
installation in this section. Retain the push rods, and counterclockwise, then tighten the rocker arm nuts
rocker arms assemblies in the same order and posi- for cylinder # 1. Torque nuts to 27 N·m (20 ft. lbs.).
tion as removed. (7) Install the cylinder head cover. Refer to cylinder
(4) Inspect the springs and retainer for cracks and head cover removal and installation in this section.
possible signs of weakening. (8) Connect the negative battery cable.
(5) Install an air hose adaptor in the fuel injector
hole.
(6) Connect an air hose to the adapter and apply
air pressure slowly. Maintain at least 621 kPa (90
psi) of air pressure in the cylinder to hold the valves
against their seats.
WJ ENGINE 9 - 33
REMOVAL AND INSTALLATION (Continued)

ENGINE CYLINDER HEAD

REMOVAL
(1) Disconnect the negative battery cable.

WARNING: DO NOT REMOVE THE CYLINDER

BLOCK DRAIN PLUGS OR LOOSEN THE RADIATOR
DRAIN COCK WITH THE SYSTEM HOT AND PRES-
SURIZED BECAUSE SERIOUS BURNS FROM THE
COOLANT CAN OCCUR.
(2) Drain the cooling system. Refer to Group 7,
Cooling System for procedure.
(3) Discharge the air conditioning system. Refer to
Group 24, Heating and Air Conditioning for procedure.
(4) Remove the A/C lines at the compressor and
cap. Refer to Group 24, Heating and Air Conditioning.
(5) Remove A/C line bracket attached to cylinder
head cover, and move A/C lines away from cylinder
head.
(6) Remove the intake manifold elbow air inlet
hose (Fig. 53).

Fig. 54 Water Manifold

1 – WATER MANIFOLD
2 – WATER MANIFOLD RETAINING BOLTS
3 – INTAKE MANIFOLD

Fig. 53 Intake Manifold Elbow

1 – INTAKE MANIFOLD ELBOW
2 – INTERCOOLER OUTLET HOSE
3 – GENERATOR
4 – UPPER RADIATOR HOSE

(7) Remove the intake manifold elbow (Fig. 53).

(8) Remove the air cleaner hose from turbocharger Fig. 55 Heater Hoses
and breather hose. 1 – HEATER CORE SUPPLY/RETURN HOSES
(9) Remove the upper radiator hose and coolant 2 – EGR VALVE
recovery hose. 3 – TURBOCHARGER
4 – FRONT
(10) Remove the water manifold (Fig. 54).
5 – HEATER CORE LINES/EGR VALVE RETAINING BOLTS
(11) Disconnect the heater hoses (Fig. 55).
9 - 34 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(12) Remove the EGR valve/heater core supply line (16) Disconnect the oil return line from turbo-
retaining bolts charger (Fig. 57).
(13) Remove the heater core supply lines
(14) Remove the exhaust manifold/turbocharger
heat shield (Fig. 56).

Fig. 57 Oil Return Line

1 – ENGINE OIL PAN
2 – TURBOCHARGER ASSEMBLY
3 – TURBOCHARGER OIL RETURN LINE
4 – TURBOCHARGER RETAINING NUT

(17) Raise vehicle on hoist.

(18) Disconnect the exhaust pipe at the turbo-
Fig. 56 Exhaust Manifold/Turbocharger Heat Shield charger.
1 – EXHAUST MANIFOLD/TURBOCHARGER HEATSHIELD (19) Remove the Exhaust manifold and turbo-
2 – HEATSHIELD RETAINING BOLTS charger. Refer to Group 11, Exhaust System and Tur-
3 – HEATER CORE SUPPLY/RETURN LINES bocharger.
4 – OIL FILTER HOUSING (20) Disconnect the boost pressure sensor electrical
5 – ENGINE OIL COOLER connector.
6 – TURBOCHARGER (21) Remove the Intake manifold. Refer to intake
manifold removal and installation procedure in this
(15) Disconnect the oil feed line from turbocharger. section.
WJ ENGINE 9 - 35
REMOVAL AND INSTALLATION (Continued)
(22) Remove the oil feed line retaining clip at rear
of the cylinder head (Fig. 58).

Fig. 59 Rocker Arm Oil Feed Lines

1 – ROCKER ARM ASSEMBLIES
2 – ROCKER ARM NUTS
3 – CYLINDER HEAD OIL SUPPLY LINE
4 – ENGINE BLOCK
5 – CYLINDER HEADS

Fig. 58 Cylinder Head Oil Supply Line Retaining Clip

1 – CYLINDER HEAD OIL SUPPLY LINE RETAINING CLIP
2 – EXHAUST MANIFOLD
3 – CYLINDER HEAD OIL SUPPLY LINE
4 – REAR OF CYLINDER HEADS
5 – CYLINDER HEAD COVER

(23) Remove the oil feed line for rocker arm

assemblies (Fig. 59).
(24) Remove the Crankcase breather hose from
front of the valve cover
(25) Remove the injector sensor wire and the glow
plug hot lead. Fig. 60 Fuel Injector Tool VM.1012B
(26) Remove the fuel injector supply lines from
injectors.
(27) Remove the fuel injectors with tool VM.1012B
(Fig. 60). Refer to Group 14, Fuel System for proce-
dure.
(28) Remove the cylinder head cover. Refer to cyl-
inder head cover removal and installation procedure
in this section.
9 - 36 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 61 Fuel Injector

(29) Remove the rocker retaining nuts (Fig. 62)
(Fig. 63).

Fig. 63 Rocker Arm Assemblies

1 – CYLINDER HEADS
2 – ROCKER ARM RETAINING NUTS
3 – ROCKER ARM SPRING PLATE
4 – ROCKER ARM ASSEMBLIES

(33) Remove the engine cylinder head bolts with

special tool VM.1018 and VM.1019.
(34) Remove the engine cylinder head and gasket.
(35) Stuff clean lint free shop towels into the cyl-
inder bores.

CYLINDER HEAD GASKETS

A one piece steel cylinder head gasket is used for
all five cylinder heads.
Cylinder head gaskets are available in three thick-
Fig. 62 Rocker Arm Retaining Nuts
nesses. Identification holes or notches in the right
1 – ROCKER ARM ASSEMBLY
front corner of the gasket indicate the thickness of
2 – ROCKER ARM RETAINING NUTS
3 – ROCKER ARM SPRING PLATE
the gasket (Fig. 64).

CAUTION: Piston protrusion must be measured, to

(30) Remove the rocker arm assemblies. Place determine cylinder head gasket thickness, if one or
them on a bench in the same order as removed. more cylinder wall liners have been replaced.
(31) Remove the push rods and place them on a
bench in the same order as removed.
(32) Mark the cylinder head positions.
WJ ENGINE 9 - 37
REMOVAL AND INSTALLATION (Continued)
(3) Zero the dial indicator on the cylinder block
mating surface.
(4) Setup the dial indicator on the piston crown
(above the center of the piston pin) 5mm (1/8 in.)
from the edge of the piston and note the measure-
ment (Fig. 66).
(5) Repeat the procedure with the rest of the cyl-
inders.
(6) Establish the thickness of the steel gasket for
all four cylinder heads on the basis of the greatest
piston protrusion (Fig. 64).

Measured dimension (mm) 0.53-0.62

Cyl. head gasket thickness (mm) 1.41
Piston clearance (mm) 0.80-0.89
Measured dimension (mm) 0.63-0.72
Cyl. head gasket thickness (mm) 1.51
Piston clearance (mm) 0.80-0.89
Measured dimension (mm) 0.73-0.82
Cyl. head gasket thickness (mm) 1.61
Piston clearance (mm) 0.80-0.89
HOW TO IDENTIFY GASKET THICKNESS
Fig. 66 Piston Protrusion Chart
NO HOLES OR NOTCHES 1.41 mm
2 HOLES OR NOTCHES 1.51 mm CAUTION: The cylinder head gasket is to be
installed DRY. DO NOT use a gasket sealing com-
1 HOLE OR NOTCHES 1.61 mm
pound on the gasket.
Fig. 64 Steel Type Cylinder Head Gasket—
identification
INSTALLATION
NOTE: If cylinder wall liners have not been (1) Remove the shop towels from the cylinder
removed; the same thickness head gasket removed, bores. Coat the bores with clean engine oil.
may be used. (2) Install cylinder head alignment studs VM.1009.
(3) After determining the correct head gasket
MEASURING PISTON PROTRUSION thickness, clean the block and head mating surfaces,
(1) Use special tool VM.1010 with dial indicator place the engine cylinder head gasket over the align-
special tool VM.1013 (Fig. 65). ment studs.
(4) Place the engine cylinder head over the align-
ment studs.

CAUTION: New cylinder head bolts must be used.

(5) Tighten the engine cylinder head bolts in

sequence according to the following procedure (Fig.
67) :
a. The threads and underside heads of the bolts
should be lubricated. Use the cylinder head align-
ment studs tool number VM-1009. Position the heads
on the block and secure with the twelve large center
bolts and spacers (clamps), finger tight only.
b. Ensure that the various clamps are installed
correctly and the head gasket remains in it’s proper
position, completely covered. Then, lubricate and
install the ten small bolts, also finger tight.
Fig. 65 Measuring Piston Protrusion (6) Install the intake and exhaust manifolds with
(2) Bring the piston of cylinder no. 1 exactly to top a new gasket, partially tightening the nuts to a max-
dead center. imum of 5 N·m (44 in. lbs.). This will align the heads.
9 - 38 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
Refer to Group 11, Exhaust System and Turbo- down completely. Then retorque the head bolts as fol-
charger for the proper procedure. lows:
(7) Then, tighten the 14mm bolts with special tool (12) Central bolts A-L: Completely back off bolts
VM.1019 in the following manner: one-by-one and then retighten to 30 N·m plus 130°
(65°). Then proceed in the same way, bolt by bolt,
following alphabetical order, as indicated.
(13) Side bolts M1-M2: Without slackening,
torque bolts M1 then bolts M2 to 90 N·m (66 ft. lbs.).
(14) Torque intake nuts to 28 N·m (20 ft. lbs.) and
exhaust manifolds nuts to 32 N·m (24 ft. lbs.) after
completing the cylinder head torquing procedure.
(15) Install the oil feed lines for the rocker arm
assemblies. Torque oil feed lines to 13 N·m (115 in.
lbs.) (Fig. 68).

Fig. 68 Oil Feed Lines

Fig. 67 Engine Cylinder Head Bolt Tightening
1 – ROCKER ARM ASSEMBLIES
Sequence
2 – ROCKER ARM NUTS
(8) 1st Phase: Tightening Head Bolts (Fig. 67). 3 – CYLINDER HEAD OIL SUPPLY LINE
Central bolts (A-L): Tighten all bolts, starting with 4 – ENGINE BLOCK
bolt I then J-K-L-A-B-C-D-E-F-G-H, to 30 N·m. 5 – CYLINDER HEADS
Tighten all bolts an additional 70°, starting with bolt
A and continuing in alphabetical order. Finally, (16) Install the oil feed line retaining clip at rear
tighten all bolts an additional 70°, starting again of the cylinder head (Fig. 69). Torque bolt to 5.5 N·m
with bolt A and continuing in alphabetical order. (4 ft. lbs.).
(9) Tighten the 12mm bolts in the following man- (17) Install the push rods. (Fig. 70).
ner:
(10) Side bolts (M1-M2): Tighten M1 bolts to 30 WARNING: During the installation of the rocker arm
N·m, then rotate them 85° (65). Tighten M2 bolts to assemblies it is possible to cause valve interfer-
30 N·m, then rotate them 85° (65). ence between the piston and valve if the piston is
near Top Dead Center (TDC). This is due to the slow
NOTE: If vehicle is equipped with A/C do not install bleed down rate of the tappets when adjusting the
A/C lines to compressor and charge A/C till Phase 2 rocker arm assemblies. Follow the procedure below
is complete. to ensure that engine damage does not occur.
(11) 2nd Phase: After 20 minutes of engine oper- • Install the rocker arm assemblies in the same
ation at operating temperature, allow engine to cool order as removed (Fig. 70).
WJ ENGINE 9 - 39
REMOVAL AND INSTALLATION (Continued)

Fig. 69 Cylinder Head Oil Supply Line Retaining Clip

1 – CYLINDER HEAD OIL SUPPLY LINE RETAINING CLIP
2 – EXHAUST MANIFOLD
3 – CYLINDER HEAD OIL SUPPLY LINE Fig. 70 Rocker Arm Assemblies
4 – REAR OF CYLINDER HEADS 1 – CYLINDER HEADS
5 – CYLINDER HEAD COVER 2 – ROCKER ARM RETAINING NUTS
3 – ROCKER ARM SPRING PLATE
4 – ROCKER ARM ASSEMBLIES
• Bring piston # 1 to Top Dead Center.
• At this point tighten the rocker arm nuts for cyl-
inder # 2–3–4–5. Torque nuts to 27 N·m (20 ft. lbs.). (28) Install the exhaust manifold/turbocharger
• Slowly rotate the crankshaft 90° clockwise or heat shield. Torque bolts to 11 N·m (8 ft. lbs.).
counterclockwise, then tighten the rocker arm nuts (29) Install the heater core supply lines.
for cylinder # 1. Torque nuts to 27 N·m (20 ft. lbs.). (30) Install the EGR valve/heater core supply line
(19) Install the cylinder head cover. Torque bolts to retaining bolts. Torque bolts to 28 N·m (20 ft. lbs.).
15 N·m (133 in. lbs.) (Fig. 71). (31) Install the intercooler hose to turbocharger.
(20) Connect the crankcase breather hose to front (32) Install the air cleaner hose to turbocharger.
of cylinder head cover. (33) Install the oil breather hose to air cleaner
(21) Connect the injector sensor wire and the glow hose.
plug hot lead. (34) Connect the recover hose to water manifold.
(22) Install the turbocharger oil feed line. Torque (35) Install the fuel injectors using special tool
banjo bolts to 27 N·m (20 ft. lbs). VM.1012B. Refer to Group 14, Fuel System for pro-
(23) Install the turbocharger oil return line. cedures.
Torque bolts to 11 N·m (97 in. lbs.). (36) Install the fuel supply lines to injectors.
(24) Install the water manifold. Torque bolts to 12 Torque nuts to 19 N·m (14 ft. lbs.).
N·m (106 in. lbs.). (37) Connect the A/C lines to compressor and
(25) Raise the vehicle on hoist. install bracket on cylinder head cover.
(26) Install the exhaust pipe to turbocharger. (38) Connect the upper radiator hose.
Torque bolts to 32 N·m (23 ft. lbs.). (39) Install the intake manifold elbow and inter-
(27) Lower vehicle form hoist. cooler hose.
9 - 40 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(2) Remove the fan and set fan inside fan shroud
then remove fan shroud and fan as an assembly.
(3) Remove the accessary drive belt. Refer to
Group 7, Cooling System for procedure.
(4) Remove the vibration damper nut.
(5) Install special tool VM.1000-A to remove vibra-
tion damper (Fig. 72).

Fig. 71 Cylinder Head Cover

1 – WATER MANIFOLD RETAINING BOLTS
2 – WATER MANIFOLD
Fig. 72 VM.1000–A
3 – CYLINDER HEAD COVER 1 – TIMING GEAR COVER
4 – CYLINDER HEAD COVER RETAINING BOLTS 2 – VIBRATION DAMPER
3 – VM.1000–A
4 – AUTOMATIC BELT TENSIONER
(40) Connect the negative cable battery.
(41) Evacuate and charge the air conditioning sys-
tem. Refer to Group 24, Heater and Air Conditioning. INSTALLATION
(42) Fill the cooling system. Check for leaks. (1) Install the vibration damper and align with
key way.
WARNING: USE EXTREME CAUTION WHEN THE (2) Install the vibration damper nut. Torque nut to
ENGINE IS OPERATING. DO NOT STAND IN DIRECT 196 N·m (147 ft. lbs.).
LINE WITH THE FAN. DO NOT PUT HANDS NEAR (3) Install the accessary drive belt. Refer to Group
THE PULLEYS, BELTS OR FAN. DO NOT WEAR 7, Cooling System for procedure.
LOOSE CLOTHING. (4) Connect the negateive battery cable.

(43) Operate the engine with the radiator cap off. TIMING GEAR COVER OIL SEAL
Inspect for leaks and continue operating the engine
until the thermostat opens. Add coolant, if required. REMOVAL
(1) Disconnect the negative battery cable.
NOTE: The one piece steel type head gasket does (2) Remove the vibration damper. Refer to vibra-
not require retorqueing. tion damper removal and installation procedure in
this section.
VIBRATION DAMPER CAUTION: Use care when removing the old seal.
Be sure not to damage the timing gear cover.
REMOVAL
(1) Disconnect the negative battery cable. (3) Pry out the old seal.
WJ ENGINE 9 - 41
REMOVAL AND INSTALLATION (Continued)
INSTALLATION TIMING GEAR COVER
The seating diameter must be 68.000 - 68.030 mm.
REMOVAL
(1) Disconnect the negative battery cable.
(2) Remove the fan and set fan inside fan shroud
then remove fan shroud and fan as an assembly.
(3) Remove the accessary drive belt. Refer to
Group 7, Cooling System for procedure.
(4) Remove the vibration damper nut.
(5) Install special tool VM.1000-A to remove the
vibration damper (Fig. 75).

Fig. 73 Timing Gear Cover Oil Seal

(1) Install the new seal using special tool
VM.1015A (Fig. 74).

Fig. 75 VM.1000–A
1 – TIMING GEAR COVER
2 – VIBRATION DAMPER
3 – VM.1000–A
4 – AUTOMATIC BELT TENSIONER

(6) Remove the fan pulley (Fig. 76).

NOTE: The idler pulleys have left hand threaded

bolts.
Fig. 74 VM.1015–A
1 – TIMING GEAR COVER (7) Remove the idler pulley and bracket (Fig. 76).
2 – VM.1015A (8) Remove the automatic belt tensioner (Fig. 76).
(9) Remove the Power steering pump pulley (Fig.
76).
(2) Install the vibration damper. Refer to vibration (10) Remove the timing gear cover.
damper removal and installation procedure in this
section.
(3) Connect the negative battery cable.
9 - 42 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 76 Idler Pulley And Tensioner Location

1 – WATER PUMP PULLEY 5 – POWER STEERING PUMP PULLEY
2 – FAN PULLEY 6 – A/C COMPRESSOR
3 – IDLER PULLEYS 7 – CRANKSHAFT PULLEY
4 – GENERATOR 8 – AUTOMATIC BELT TENSIONER

INSTALLATION (8) Install the vibration damper. Torque nut to 196

(1) Be sure the mating surfaces of the gear case N·m (147 ft. lbs.).
cover and the cylinder block are clean and free from (9) Install the accessary drive belt. Refer to Group
burrs. 7, Cooling System for procedure.
(2) Apply a continuous 3 mm bead of Silicone (10) Install the fan and fan shroud.
Sealer (Fig. 77) to timing cover, install within 10 (11) Connect the negative battery cable.
minutes, tighten 6mm bolts to 11 N·m (8 ft. lbs.) and
tighten 8mm bolts to 26.2 N·m (19 ft. lbs.). CAMSHAFT
(3) Install Power steering pump pulley. Torque
bolts to 25 N·m (18 ft. lbs.). REMOVAL
(4) Install the automatic belt tensioner. (1) Disconnect the negative battery cable.
(5) Install the idler pulley bracket. Torque bolts to (2) Remove the cylinder head cover. Refer to cylin-
47 N·m (34 ft. lbs.). der head cover removal and installation in this sec-
tion.
NOTE: The idler pulley has left hand thread. (3) Remove the cylinder heads. Refer to cylinder
head removal and installation in this section.
(6) Install the idler pulleys. Torque nut to 47 N·m (4) Remove the rocker arm assemblies, push rods,
(34 ft. lbs.). and hydraulic tappets. Refer to the respective groups
(7) Install the fan pulley. Torque bolts to 28 N·m in this section.
(21 ft. lbs.). (5) Remove the fan and set fan inside fan shroud
then remove fan shroud and fan as an assembly.
WJ ENGINE 9 - 43
REMOVAL AND INSTALLATION (Continued)

Fig. 77 Front Cover Sealer Location

1 – MOPAR SILICONE RUBBER ADHESIVE SEALANT
Fig. 78 Timing Marks
1 – VACUUM PUMP
(6) Remove the accessary drive belt. Refer to
2 – CAMSHAFT
Group 7, Cooling System for procedure.
3 – INJECTION PUMP
(7) Remove the radiator, A/C condensor, and inter- 4 – TIMING MARKS
cooler as an assembly. Refer to Group 7, Cooling Sys- 5 – OIL PUMP
tem for procedure. 6 – CRANKSHAFT
(8) Remove the vibration damper. Refer to vibra-
tion damper removal and installation in this section.
(9) Remove the power steering pump pulley.
(10) Remove timing gear cover. Refer to timing
gear cover removal and installation in this section.
(11) Rotate the engine to align the timing marks
as shown (Fig. 78).

NOTE: The oil dipstick tube must be removed for

camshaft removal.

(12) Unscrew the flange bolts and remove cam-

shaft (Fig. 79).

THRUST PLATE INSPECTION

Check the thickness (Fig. 80) of the plate at points
a-b-c-d. If the measurement is not between 3.950 -
4.050 it must be changed.

INSTALLATION
(1) Coat the camshaft journals with clean engine
oil and carefully install the camshaft complete with
thrust plate and gear. Tighten retaining bolts to 18
N·m (13 ft. lbs.). Be sure to align the timing marks Fig. 79 Camshaft Removal
as shown (Fig. 81).
(3) Install the cylinder heads. Refer to cylinder
(2) Install the hydraulic tappets and retainers.
head removal and installation in this section.
Refer to hydraulic tappet removal and installation in
(4) Install the push rods and rocker arm assem-
this section.
blies. Refer to the respective sections.
9 - 44 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(9) Install the fan and fan shroud,. Torque fan to
56 N·m (41 ft. lbs.).
(10) Evacuate and charge the air conditioning sys-
tem. Refer to Group 24, Heater and Air Conditioning
for procedure.
(11) Connect the negative battery cable.
(12) Fill the cooling system. Check for leaks.

WARNING: USE EXTREME CAUTION WHEN THE

ENGINE IS OPERATING. DO NOT STAND IN DIRECT
LINE WITH THE FAN. DO NOT PUT HANDS NEAR
THE PULLEYS, BELTS OR FAN. DO NOT WEAR
LOOSE CLOTHING.

(13) Operate the engine with the radiator cap off.

Inspect for leaks and continue operating the engine
until the thermostat opens. Add coolant, if required.

Fig. 80 Camshaft Thrust Plate CAMSHAFT BEARINGS

This procedure requires that the engine is removed
from the vehicle.

REMOVAL
(1) With the engine completely disassembled,
install the Camshaft Bearing Remover/Installer Tool
VM.1040 (Fig. 82).

Fig. 81 Timing Marks

1 – CAMSHAFT GEAR
2 – CRANKSHAFT GEAR
3 – OIL PUMP
4 – VACUUM PUMP

(5) Install the cylinder head cover. Refer to cylin-

der head cover removal and installation in this sec-
tion.
(6) Install the timing gear cover. Refer to timing Fig. 82 VM.1040
1 – VM.1040
gear cover removal and installation in this section.
2 – CAMSHAFT BEARING
(7) Install the vibration damper. Refer to the 3 – CYLINDER BLOCK
vibration damper removal and installation in this
section.
(8) Install the radiator, A/C condensor, and inter- (2) Pull the camshaft bearings out of the cylinder
cooler. Refer to Group 7, Cooling System for proce- block.
dure.
WJ ENGINE 9 - 45
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
CAUTION: Be sure the oil holes in the center bear-
ings are lined up with oil gallery holes in the cylin-
der block.

(1) Install the front and rear camshaft bearings

with Camshaft Bearing Remover/Installer Tool
VM.1040.
(2) Install the remaining bearings in the same
manner. The Bearings must be carefully aligned to
bring oil holes into full register with oil passages
from the main bearing. If the camshaft bearing shell
oil holes are not in exact alignment, remove and
install them correctly.

OIL PAN
REMOVAL
(1) Disconnect the negative battery cable.
Fig. 83 Oil Pump Removal
(2) Raise the vehicle on hoist.
1 – CAMSHAFT GEAR
(3) Drain the oil. 2 – CRANKSHAFT GEAR
(4) Remove the oil pan lower cover. 3 – OIL PUMP
(5) Remove the bolts from oil pan. Remove the 6 4 – VACUUM PUMP
bolts that are on the inside of the oil pan.
(6) Remove the oil pan.
(2) Install the oil pump. Torque screws to 28 N·m
INSTALLATION (20 ft. lbs.). Check for normal backlash between
(1) Remove all gasket material from cylinder block. pump and crankshaft gears.
Be careful not gouge or scratch aluminum pan seal- (3) Install the timing gear cover. Refer to timing
ing surface. gear cover removal and installation in this section.
(2) Apply a continuous 3 mm bead of Silicone (4) Connect the negative battery cable.
Sealer to oil pan, install within 10 minutes. Install
the oil pan. INTERNAL VACUUM PUMP
(3) Install the oil pan bolts. Torque bolts to 13 N·m
(9 ft. lbs.). REMOVAL
(4) Install the oil pan lower cover. Torque bolts to (1) Disconnect the negative battery cable.
13 N·m (9 ft. lbs.). (2) Remove the timing gear cover. Refer to timing
(5) Install the oil drain plug. Torque to 79 N·m (58 gear cover removal and installation in this section.
ft. lbs). (3) Align all the timing marks before removing the
(6) Lower the vehicle from hoist. vacuum pump (Fig. 84).
(7) Fill engine with proper amount of oil. (4) Remove the vacuum pump retaining bolts..
(8) Connect the negative battery cable. (5) Remove the internal vacuum pump.

OIL PUMP INSTALLATION

(1) To install the vacuum pump, align the outer
REMOVAL part of the gear with the inner part using a screw-
(1) Disconnect the negative battery cable. driver or similar tool, align with timing marks on
(2) Remove the timing gear cover. Refer to timing gear set and install (Fig. 84). Torque bolts to 28 N·m
gear cover removal and installation in this section. (20 ft. lbs.).
(3) Remove the oil pump (Fig. 83). (2) Install the timing gear cover. Refer to timing
gear cover removal and installation in this section.
INSTALLATION (3) Connect the negative battery cable.
(1) Install new O-ring and lubricate with clean
engine oil.
9 - 46 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 84 Timing Marks Fig. 86 Vacuum Pump Parts

1 – VACUUM PUMP 1 – O-RING
2 – CAMSHAFT 2 – ROTOR BLADES
3 – INJECTION PUMP 3 – VACUUM PUMP
4 – TIMING MARKS
5 – OIL PUMP
6 – CRANKSHAFT

Fig. 87 Vacuum Pump Mounting Hole

Fig. 85 Vacuum Pump

OIL PUMP PRESSURE RELIEF VALVE
1 – VACUUM PUMP
2 – CAMSHAFT
REMOVAL
3 – OIL PUMP (1) Disconnect the negative battery cable
4 – CRANKSHAFT (2) Remove the oil pan. Refer to oil pan removal
and installation procedure in this section.
WJ ENGINE 9 - 47
REMOVAL AND INSTALLATION (Continued)
(3) Remove the relief valve snap ring.
(4) Remove the relief valve cap, spring, and
plunger (Fig. 88).
(5) Check the relief valve spring length. Relief
valve spring free length is 57.5mm (2.263 in.). If
spring length is less or spring is distorted it must be
replaced.
(6) Check the plunger for scoring, replace if neces-
sary.

Fig. 89 Oil Filter Housing

1 – OIL FILTER HOUSING
2 – OIL COOLER
3 – AUTOMATIC BELT TENSIONER

Fig. 88 Oil Pressure Relief Valve

INSTALLATION
(1) Thoroughly clean all components and relief
valve pocket in cylinder block.
(2) Fit plunger, spring and cap into block.
(3) Compress spring and install the snap ring.
Ensure the snap ring is completely seated in groove.
(4) Install the oil pan. Refer to oil pan removal
and installation procedure in this section.
(5) Connect the negative battery cable.

OIL FILTER ADAPTER AND OIL COOLER

REMOVAL
(1) Disconnect the negative battery cable.
(2) Remove the oil cooler coolant hoses.
(3) Remove the oil filter housing/oil cooler retain- Fig. 90 Oil Cooler
ing bolt (Fig. 89).
(4) Remove the oil filter housing and oil cooler
(Fig. 90).
9 - 48 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Install the oil cooler and oil filter housing with
a new gasket. Torque bolt to 46.6 N·m (34 ft. lbs.).
(2) Install the oil cooler coolant hoses.
(3) Connect the negative battery cable.

ENGINE OIL FILTER

REMOVAL

Fig. 92 Oil Filter Housing Cap

1 – AUTOMATIC BELT TENSIONER
2 – OIL PAN
3 – OIL FILTER HOUSING CAP

(7) Clean the oil filter housing and housing cap

with shop solvent

INSTALLATION
(1) Install a new sealing o-ring in the housing cap
and lubricate with fresh engine oil.
(2) Install the new filter element in the housing
and install cap (Fig. 92). Torque to 22.5 N·m (194in.
lbs.).
Fig. 91 Oil Filter Position & Orientation (3) Install the oil filter housing drain plug. Torque
1 – OIL FILTER HOUSING to 12 N·m (106in. lbs.).
2 – OIL FILTER HOUSING AND OIL COOLER RETAINING BOLT
(4) Lower the vehicle on hoist.
3 – AUTOMATIC BELT TENSIONER RETAINING BOLT
4 – AUTOMATIC BELT TENSIONER
(5) Fill the engine oil level to specification.
5 – OIL FILTER HOUSING CAP (6) Start the engine and check for leaks.

PISTONS AND CONNECTING ROD ASSEMBLY

(1) Raise the vehicle on a hoist.
(2) Position a drainpan under the oil filter housing REMOVAL
(Fig. 92). (1) Disconnect the battery cable.
(3) Remove the oil filter housing drain plug. (2) Remove cylinder heads, refer to cylinder head
Located in the center of the housing cap. Drain the removal and installation in this section.
engine oil from the oil filter housing. (3) Raise vehicle on host.
(4) Remove the oil filter housing cap by rotating (4) Remove oil pan, refer to oil pan removal and
counter-clockwise. installtion in this section.
(5) If the element remains in the housing remove (5) Remove top ridge of cylinder bores with a ridge
the oil filter element by pulling it straight down and reamer before removing pistons from cylinder block.
out of the oil filter housing. Be sure to keep tops of pistons covered during
(6) Remove the oil filter housing sealing o-ring this operation. Mark piston with matching cylinder
from the housing cap and discard. A new o-ring is number.
supplied with the oil filter element.
WJ ENGINE 9 - 49
REMOVAL AND INSTALLATION (Continued)
(6) Pistons and connecting rods must be removed
from top of cylinder block. Rotate crankshaft so that
each connecting rod is centered in cylinder bore.
(7) Remove connecting rod cap bolts and cap. Push
each piston and rod assembly out of cylinder bore.

NOTE: Be careful not to nick crankshaft journals.

(8) After removal, install bearing cap on the mat-

ing rod.

Fig. 94 Piston Rings—Removing and Installing

(3) Remove the upper oil ring side rail, lower oil
ring side rail and then oil ring expander from piston.
(4) Carefully clean carbon from piston crowns,
skirts and ring grooves ensuring the 4 oil holes in
the oil control ring groove are clear.

PISTON RING FITTING

(1) Wipe cylinder bore clean. Insert ring and push
down with piston to ensure it is square in bore. The
ring gap measurement must be made with the ring
positioning at least 12 mm (0.50 in.) from bottom of
cylinder bore. Check gap with feeler gauge. Top com-
pression ring gap.25 to.50mm (.0098 to.0196 in.). Sec-
ond compression ring gap.25 to.35mm (.0098 to.0137
in.). Oil control ring gap.25 to.58mm (.0098 to.0228
in.).

Fig. 93 Piston Assembly

PISTON PIN—REMOVAL
(1) Secure connecting rod in a soft jawed vice.
(2) Remove 2 clips securing piston pin.
(3) Push piston pin out of piston and connecting
rod.

PISTON RING—REMOVAL
(1) ID mark on face of upper and intermediate pis-
ton rings must point toward piston crown.
(2) Using a suitable ring expander, remove upper
and intermediate piston rings (Fig. 94).
Fig. 95 Ring Gap Measurement
1 – FEELER GAUGE
9 - 50 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(2) If ring gaps exceed dimension given, new rings
or cylinder liners must be fitted. Keep piston rings in
piston sets.
(3) Check piston ring to groove clearance (Fig. 96).
Top compression ring gap.08 to.130mm (.0031 to.0051
in.). Second compression ring gap.070 to.102mm
(.0027 to.0040 in.). Oil control ring gap.040 to.072mm
(.0015 to.0028 in.).

Fig. 98 Piston Ring Identification

(2) Top compression ring is tapered and chromium
plated. The second ring is of the scraper type and
must be installed with scraping edge facing bottom of
the piston. The third is an oil control ring. Ring gaps
must be positioned, before inserting piston into the
liners, as follows (Fig. 99).
(3) Top ring gap must be positioned at 30 degrees
to the right of the combustion chamber recess (look-
ing at the piston crown from above).
(4) Second piston ring gap should be positioned on
the opposite side of the combustion chamber recess.
(5) Oil control ring gap to be located 30 degrees to
the left of combustion chamber recess.
Fig. 96 Piston Ring to Groove Clearance (6) When assembling pistons check that compo-
nents are installed in the same position as before dis-
PISTON RINGS—INSTALLATION assembly, determined by the numbers stamped on
(1) Install rings on the pistons using a suitable the crown of individual pistons. Engine cylinders are
ring expander (Fig. 97). numbered starting from gear train end of the engine.
Face chamber recess side of piston towards
camshaft. Therefore, the numbers stamped on con
rod big end should also face in the same direction. To
insert piston into cylinder use a ring compressor as
shown in (Fig. 100).

PISTON PIN INSTALLATION

(1) Secure connecting rod in soft jawed vice.
(2) Lubricate piston pin and piston with clean oil.
(3) Position piston on connecting rod.

CAUTION: Ensure combustion recess in piston

crown and the bearing cap numbers on the con-
necting rod are on the same side.

(4) Install piston pin.

Fig. 97 Piston Rings—Removing and Installing (5) Install clips in piston to retain piston pin.
(6) Remove connecting rod from vice.
WJ ENGINE 9 - 51
REMOVAL AND INSTALLATION (Continued)
INSTALLATION (3) Immerse the piston head and rings in clean
(1) Before installing pistons, and connecting rod engine oil, slide the ring compressor, over the piston
assemblies into the bore, be sure that compression and tighten with the special wrench (Fig. 100).
ring gaps are staggered so that neither is in line with Ensure position of rings does not change dur-
oil ring rail gap (Fig. 99). ing this operation.
• The top piston ring gap must be positioned at 30 (4) Face chamber recess side of piston towards
degrees to the right of the combustion chamber camshaft.
recess (looking at the piston crown from above). (5) Rotate crankshaft so that the connecting rod
• The second piston ring gap should be positioned journal is on the center of the cylinder bore. Insert
on the opposite side of the combustion chamber rod and piston into cylinder bore and guide rod over
recess. the crankshaft journal.
• The piston oil control ring gap is to be located 30 (6) Tap the piston down in cylinder bore, using a
degrees too the left of the combustion chamber hammer handle. At the same time, guide connecting
recess. rod into position on connecting rod journal.
(7) Install rod caps. Install cleaned and oiled rod
bolts. Torque bolts to 29.5 N·m (22 ft. lb.) plus 60°.

CYLINDER WALL LINER ASSEMBLY

REMOVAL
(1) Disconnect the negative battery cable
(2) Remove the engine from vehicle.
(3) With the engine completely disassembled,
install the Cylinder Liner Puller Tool VM-1001 to
remove liners (Fig. 101) (Fig. 102).

Fig. 99 Piston Ring Gap Location

(2) Before installing the ring compressor, make
sure the oil ring expander ends are butted and the
rail gaps located as shown in (Fig. 99).

Fig. 100 Installing Piston

Fig. 101 Liner Removal Tool

(4) Remove shims from cylinder liner or cylinder
block recess. Keep shims with each cylinder liner.
9 - 52 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Carefully clean residual LOCTITE from liner
and crankcase, and degrease the crankcase where it
comes into contact with the liners. Install the liners
in the crankcase as shown (A), rotating them back
and forth by 45° in order to guarantee correct posi-
tioning (Fig. 104).
(2) Measure the liner recess relative to block deck
with a dial indicator mounted on a special tool
VM-1010 A. All the measurements must be taken
on camshaft side. Zero dial gauge on block deck.
(3) Move dial gauge to cylinder liner record read-
ing on dial gauge.
(4) Remove liner and special tool.
(5) Then select the correct shim thickness to give
proper protrusion (0.01 - 0.06 mm).
(6) Fit the shim and the O-rings onto the liner.
(7) Lubricate the lower liner location in the block.
Apply LOCTITE AVX to the corner of the liner seat.
Apply LOCTITE AVX uniformly to the upper part of
the liner at area.
(8) Fit the liners in the crankcase making sure
Fig. 102 VM.1001 that the shim is positioned correctly in the seat. Lock
1 – VM.1001 the liners in position using special tool (VM-1016)
2 – CYLINDER BLOCK and bolts (Fig. 105). Clean the residual LOCTITE on
3 – CYLINDER LINER the upper surface of the block deck.
(9) Recheck the liner protrusion. It should be 0.01
- 0.06 mm.

NOTE: A period of six hours must elapse between

the liners being installed and engine start-up. If
engine assembly is not continued after liner instal-
lation, the liners need to be clamped for twelve
hours minimum.

FLEXPLATE
REMOVAL
NOTE: This must be done with the engine or trans-
mission removed from the vehicle.

Fig. 103 Liner Inspection (1) Remove the six flexplate mounting bolts and
the flexplate.
WJ ENGINE 9 - 53
REMOVAL AND INSTALLATION (Continued)

Fig. 104 Liner Installation

INSTALLATION TRANSMISSION PILOT BUSHING
(1) Install the flexplate on the flexplate adapter
hub. REMOVAL
(2) Install the flexplate mounting bolts.
(3) With the flexplate mounting bolts still loose, NOTE: This requires the transmission or the engine
rotate the flexplate clockwise looking from the back to be removed from the vehicle.
of the engine. This will eliminate any backlash
between the flexplate and mounting bolts. (1) Install special tool VM-8399 into the transmis-
(4) Torque the mounting bolts to 44 N·m. sion pilot bushing (Fig. 106).
(2) Tighten special tool VM-8399 to remove the
transmission pilot bushing (Fig. 107).
9 - 54 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 107 Transmission Pilot Bushing Removal

Fig. 105 Liner Clamp Location 1 – TRANSMISSION PILOT BUSHING
1 – VM.1016 2 – FLEXPLATE ADAPTER HUB
2 – CYLINDER LINER
3 – CYLINDER BLOCK
(2) Install special tool VM-8372 on the flexplate
adapter hub (Fig. 108).

Fig. 106 Transmission Pilot Bushing

Fig. 108 VM-8372
1 – FLEXPLATE ADAPTER HUB
1 – FLEXPLATE ADAPTER HUB
2 – TRANSMISSION PILOT BUSHING
2 – TRANSMISSION PILOT BUSHING

INSTALLATION (3) Tighten the center bolt on special tool VM-8372

(1) Place the transmission pilot bushing into the to install the transmission pilot bushing.
flexplate adapter hub.
WJ ENGINE 9 - 55
REMOVAL AND INSTALLATION (Continued)
(4) Once the transmission pilot bushing is (4) Remove the accessary drive system.
installed, remove the special tool VM-8372. (5) Remove the cylinder heads. Refer to cylinder
(5) Use special tool VM-8390 to make sure pilot head removal and installation in this section.
bushing is installed to proper depth (Fig. 109). Be (6) Remove the oil pan and oil pick-up.
sure that the outside edges of special tool (7) Remove the pistons and connecting rods.
VM-8390 make contact with the flexplate (8) Remove the vibration damper. Refer to vibra-
adapter hub. If contact is not made remove the tion damper removal and installation in this section.
transmission pilot bushing and check for debris (9) Remove the timing gear cover. Refer to timing
in the flexplate adapter hub. Then reinstall the gear cover removal and installation in this section.
transmission pilot bushing into the flexplate (10) Remove the oil pump and vacuum pump from
adapter hub. block.
(11) Install special tool VM.1004 onto crankshaft
over gear (Fig. 110).

Fig. 109 Transmission Pilot Bushing Gauge

VM-8390
1 – TRANSMISSION PILOT BUSHING Fig. 110 Crankshaft Special Tool VM.1004
2 – FLEXPLATE ADAPTER HUB 1 – TOOL

CRANKSHAFT AND MAIN BEARINGS (12) Remove the main bearing oil feed and crank-
shaft support locators from block.
REMOVAL (13) Remove the flexplate and adaptor plate from
(1) Disconnect the negative battery cable. engine block.
(2) Remove the engine from vehicle. Refer to (14) Remove the thrust bearings from rear main
engine removal and installation in this section. bearing carrier.
(3) Install the engine on an engine stand. (15) Slide the crankshaft and bearing carriers
rearward to rear of cylinder block. Remove crank-
shaft from the rear of the cylinder block.
9 - 56 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)
(16) Mark the carriers for assembly and remove
the bolts, two for each carrier. Separate the two
halves of each carrier, remove from the crankshaft
and temporarily re-assemble the carriers (Fig. 111).

Fig. 112 Crankshaft Front Main Bearing Removal

1 – CYLINDER BLOCK
2 – VM.1002

Fig. 111 Crankshaft and Carrier Bearing Assembly

1 – CRANKSHAFT SUPPORT
2 – CRANKSHAFT MAIN BEARING HALVE
3 – CRANKSHAFT MAIN BEARING HALVE
4 – CRANKSHAFT SUPPORT BOLTS
5 – CRANKSHAFT GEAR
6 – CRANKSHAFT
7 – CRANKSHAFT KEY

(17) Install the Crankshaft Bearing Remover/In-

staller VM.1002 on the front main bearing (Fig. 112).
(18) Using the VM.1002 pull the front main bear-
ing out of the cylinder block (Fig. 112).

INSTALLATION
Fig. 113 Crankshaft Front Main Bearing Installation
NOTE: Be sure that the oil hole in the main bearing 1 – FRONT CRANKSHAFT MAIN BEARING
lines up with the oil gallery hole in the cylinder 2 – CYLINDER BLOCK
block. 3 – VM.1002

(1) Using the VM.1002 push the front main bear-

(4) If internal diameter of original bearing is being
ing into the cylinder block (Fig. 113).
checked and figures are not within specifications,
(2) Fit the main bearing supports together. Torque
new bearings must be used.
to 44 N·m (32 ft. lbs.)
(3) Check internal diameter of bearings.
WJ ENGINE 9 - 57
REMOVAL AND INSTALLATION (Continued)
(5) Check the crankshaft main bearing journals to (13) Install the new O-rings in adaptor plate.
bearing clearances. Clearances of main bearings is.03 (14) Install the adaptor plate to block. Torque nuts
to.088mm (.0011 to.0035 in.). to 28 N·m (20 ft. lbs.).
(15) Install the Allen bolts through adaptor plate
NOTE: Assemble engine according to sequence to rear main bearing support. Torque to 11 N·m (97
described, thus saving time and preventing dam- in. lbs.).
ages to engine components. Clean parts with a suit- (16) Position the flexplate adapter hub and O-ring
able solvent and dry them with compressed air on crankshaft and align bolt holes.
before assembly. Use new gaskets where applicable
and torque wrenches for correct tightening of com- NOTE: For purposes of checking crankshaft end
ponents. play, used adapter hub bolts may be used. Final
assembly requires new adapter hub bolts.
(6) Thoroughly clean crankcase and oil passages,
and blow dry with compressed air. (17) Install 2 adapter hub bolts, 180° apart, and
(7) Install new main bearing shells in each of the tighten bolts to 20 N·m plus 60° (15 ft. lbs.) plus 60°.
carrier halves. Assemble the carriers to the crank- (18) Attach dial indicator to engine block.
shaft journals, ensuring that the carriers are (19) Move crankshaft toward front of engine and
installed in their original locations. Secure each car- zero indicator.
rier with the two bolts tightening evenly to 44 N·m (20) Move crankshaft toward the rear of engine
(32 ft. lbs.). and record measurement.
(8) Slide special tool VM.1004 over the crankshaft (21) Subtract specified crankshaft end play from
gear and, insert the crankshaft and support assembly figure obtained. Crankshaft end play 0.08 to 0.28 mm
into the crankcase in the same manner used for (.0060 to.0119 in.).
removal. (22) Select thrust washers which will give correct
(9) Align the holes in the lower supports, with the end play.
center of the crankcase webs (Fig. 114). (23) Remove tools and adapter hub.
(24) Lubricate thrust washer halves and fit them
into the rear main bearing carrier.
(25) Ensure that crankshaft end and adapter hub
mating surfaces are clean and dry. Install “O” ring in
adapter hub groove.
(26) To verify correct end play, install 2 adapter
hub bolts 180° apart, and tighten bolts to 20 N·m
plus 60° (15 ft. lbs. plus 60°).
(27) Measure crankshaft end play with a dial
gauge. Crankshaft end play should not exceed 0.08 to
0.28 mm (.0060 to.0119 in.) (Fig. 115).

CAUTION: Use NEW adapter hub bolts for the fol-

lowing procedure.

(28) Install a new O-ring on adapter hub. Install

adapter hub on crankshaft. The 6 adapter hub bolts
must be tightened as follows:
a. Lubricate and install the 6 new adapter hub
bolts.
b. Torque the 6 adapter hub bolts to 50 N·m (36 ft.
lbs.) starting one bolt and following with the opposite
Fig. 114 Main Bearing Support Alignment one (cross tightening) until completion, in a clockwise
direction..
(10) Secure each support assembly to the crank- c. Loosen one bolt at a time and tighten to 20 N·m
case with the main bearing oil feed and support loca- (14 ft. lbs.) plus 75° using the cross tightening
tors. Torque to 54 N·m (40 ft. lbs). method.
(11) Install the rear main bearing support onto (29) Install the pistons and connecting rod assem-
crankshaft ensuring arrow on bearing support aligns blies. Refer to piston and connecting rods removal
with vertical web in center of crankcase. and installation in this section.
(12) Install the rear oil seal.
9 - 58 ENGINE WJ
REMOVAL AND INSTALLATION (Continued)

Fig. 116 Oil Pump Bore Depth

(38) Install the rocker arms and push rods. Refer
to rocker arm and push rod removal and installation
in this section.
(39) Install the cylinder head cover. Refer to cylin-
der head cover removal and installation in this sec-
Fig. 115 Measuring Crankshaft End Play tion.
1 – DIAL INDICATOR (40) Install the accessary drive system.
2 – ADAPTER PLATE
(41) Install the engine in vehicle. Refer to engine
3 – ENGINE BLOCK
removal and installation in this section.
4 – SCREW DRIVE OR PRY BAR
5 – CRANKSHAFT
(42) Fill engine with the correct amount of fluids
6 – FLEXPLATE ADAPTER HUB specified.
7 – TRANSMISSION PILOT BUSHING (43) Connect the negativre battery cable.

(30) Install the oil pick up tube. Torque bolts to 25 DISASSEMBLY AND ASSEMBLY
N·m (18 ft. lbs.).
(31) Install the oil pan. Refer to oil pan removal HYDRAULIC TAPPETS
and installation in this section.
(32) Install the vacuum pump, being careful to DISASSEMBLE
align the gear timing marks with those on the crank- (1) Pry out plunger retainer spring clip.
shaft gear. Torque screws to 20 N·m (15 ft. lbs.). (2) Clean varnish deposits from inside of tappet
(33) Before installing the oil pump check pump body above plunger cap.
bore depth in block (A) and pump body height (B) (3) Invert tappet body and remove plunger cap,
(Fig. 116). Difference between A and B should be plunger, check valve, check valve spring, check valve
0.020-0.082 mm (.0007 to 0032 in.). retainer and plunger spring. Check valve could be
(34) Install the oil pump. Torque screws to 27 N·M flat or ball.
(20 ft.lbs.). Check for normal backlash between pump
and crankshaft gears. ASSEMBLE
(35) Install the timing gear cover. Refer to timing (1) Clean all tappet parts in a solvent that will
gear cover removal and installation in this section. remove all varnish and carbon.
(36) Install the vibration damper. Refer to vibra- (2) Replace tappets that are unfit for further ser-
tion damper removal and installation in this section. vice with new assemblies.
(37) Install the cylinder heads. Refer to cylinder
head removal and installation in this section.
WJ ENGINE 9 - 59
DISASSEMBLY AND ASSEMBLY (Continued)
(3) If plunger shows signs of scoring or wear,
install a new tappet assembly. If valve is pitted, or
valve seat on end of plunger is prevented from seat-
ing, install a new tappet assembly.
(4) Assemble tappets.

CLEANING AND INSPECTION

CYLINDER HEAD
CLEANING
Thoroughly clean the engine cylinder head and cyl-
inder block mating surfaces. Clean the intake and
exhaust manifold and engine cylinder head mating
surfaces. Remove all gasket material and carbon.
Check to ensure that no coolant or foreign material
has fallen into the tappet bore area.
Remove the carbon deposits from the combustion
chambers and top of the pistons.

INSPECTION
Use a straightedge and feeler gauge to check the
flatness of the engine cylinder head and block mating
surfaces (Fig. 117).
Minimum cylinder head thickness 89.95mm (3.541
in.)

CAUTION: If only one cylinder head is found to be Fig. 118 Rocker Arm Components
distorted and requires machining, it will also be 1 – ROCKER ARM
necessary to machine the remaining cylinders 2 – SPRING PLATE
3 – ROCKER SUPPORT
heads and end plates by a corresponding amount
4 – PUSH ROD
to maintain correct cylinder alignment.
5 – HYDRAULIC TAPPET
6 – CAMSHAFT
7 – ANTIROTATION BRACKET

INSPECTION
Inspect the pivot surface area of each rocker arm.
Replace any that are scuffed, pitted, cracked or
excessively worn.
Inspect the valve stem tip contact surface of each
rocker arm and replace any rocker arm that is deeply
pitted.
Inspect each push rod end for excessive wear and
Fig. 117 Checking Cylinder Head Flatness
replace as required. If any push rod is excessively
ROCKER ARMS AND PUSH RODS worn because of lack of oil, replace it and inspect the
corresponding hydraulic tappet for excessive wear.
CLEANING Inspect the push rods for straightness by rolling
Clean all the components (Fig. 118) with cleaning them on a flat surface or by shining a light between
solvent. the push rod and the flat surface.
Use compressed air to blow out the oil passages in A wear pattern along the length of the push rod is
the rocker arms and push rods. not normal. Inspect the engine cylinder head for
obstruction if this condition exists.
9 - 60 ENGINE WJ
CLEANING AND INSPECTION (Continued)

PISTONS AND CONNECTING ROD ASSEMBLY

INSPECTION—PISTONS
(1) Piston Diameter: Size: 91.93-91.94mm (3.6191-
3.6196 in.) Maximum wear limit.05mm (.0019 in.).
(2) Check piston pin bores in piston for roundness.
Make 3 checks at 120° intervals. Maximum out of
roundness.05mm (.0019in.).
(3) The piston diameter should be measured
approximately 15 mm (.590 in.) up from the base.
(4) Skirt wear should not exceed 0.1 mm (.00039
in.).
(5) The clearance between the cylinder liner and
piston should not exceed 0.25 mm (.0009 in.).
(6) Make sure the weight of the pistons does not
differ by more than 5 g.
Fig. 119 Connecting Rod Identification
1 – CAMSHAFT SIDE
INSPECTION—CONNECTING ROD 2 – 2–DIGIT NUMBER FOR WEIGHT CATEGORY
(1) Assemble bearing shells and bearing caps to 3 – 4–DIGIT REFERENCE NUMBERS FOR CORRECT
their respective connecting rods ensuring that the ASSEMBLING
serrations on the cap and reference marks are
aligned.
(2) Tighten bearing cap bolts to 29N·m (21 ft. lbs.)
plus 60°.
(3) Check and record internal diameter of crank
end of connecting rod.

NOTE: When changing connecting rods, all five

must have the same weight and be stamped with
the same number. Replacement connecting rods
will only be supplied in sets of five.

Connecting rods are supplied in sets of five since

they all must be of the same weight category. Max
allowable weight difference is 18 gr.

NOTE: On one side of the big end of the con-rod

there is a two-digit number which refers to the
weight category. On the other side of the big end
there is a four digit number on both the rod and the
cap. These numbers must both face the camshaft
as well as the recess on the piston crown (Fig. 120).
Lightly heat the piston in oven. Insert piston pin in
position and secure it with provided snap rings. Fig. 120 Piston and Connecting Rod Assembly
INSPECTION—CRANKSHAFT JOURNALS
The Four digit numbers marked on con rod
(1) Using a micrometer, measure and record crank-
big end and rod cap must be on the same side
shaft connecting rod journals, take reading of each
as the camshaft (Fig. 120). After having coated
journal 120° apart. Crankshaft journal diameter is
threads with Molyguard, tighten con rod bolts to 29
53.84 to 53.955mm (2.1196 to 2.1242 in.).
N·m (21 ft. lbs.) plus 60°.
(2) Crankshaft journals worn beyond limits or
show signs of out of roundness must be reground or
INSPECTION—PISTON PIN replaced. Minimum reground diameter is 53.69mm
(1) Measure the diameter of piston pin in the cen-
(2.1137 in.).
ter and both ends.
(2) Piston pin diameter is 29.990 to 29.996mm
(1.1807 to 1.1809 in.).
WJ ENGINE 9 - 61
CLEANING AND INSPECTION (Continued)
BEARING-TO-JOURNAL CLEARANCE OIL PUMP
Compare internal diameters of connecting rod with
crankshaft journal diameter. Maximum clearance CLEANING
between connecting rod and crankshaft journals.022 Wash all parts in a suitable solvent and inspect
to.076mm (.0008 to.0029 in.). carefully for damage or wear.

INSPECTION
(1) Before installing oil pump check pump bore
depth in block (A) and pump body height (B) (Fig.
123). Difference between A and B should be
0.020-0.082 mm.

Fig. 121 Bearing Clearance

CYLINDER WALL LINER ASSEMBLY
INSPECTION
The cylinder walls should be checked for out-of-
round and taper with dail bore gauge. The cylinder
bore out-of-round is 0.100 mm (.0039 inch) maximum
and cylinder bore taper is 0.100 mm (0.0039 inch)
maximum. If the cylinder walls are badly scuffed or
scored, new liners should be installed and honed, and
new pistons and rings fitted.
Measure the cylinder bore at three levels in direc-
Fig. 123 Oil Pump Bore Depth
tions A and B (Fig. 122). Top measurement should be
10 mm ( 3/8 inch) down and bottom measurement
should be 10 mm ( 3/8 inch.) up from bottom of bore.

Fig. 124 Oil Pump Inner and Outer Rotors

1 – OUTER ROTOR
2 – INNER ROTOR
Fig. 122 Liner Inspection
9 - 62 ENGINE WJ
CLEANING AND INSPECTION (Continued)
(2) Check clearance between rotors (Fig. 125). DESCRIPTION SPECIFICATIONS
-0.125 . . . . . . . . . . . . . . . . . . . . . 62.925-62.968 mm
Clearance between journal
and bearing: 0.030-0.088
Rear journal diameter
Nominal . . . . . . . . . . . . . . . . . . . 79.980-80.000 mm
-0.25 . . . . . . . . . . . . . . . . . . . . . . 79.730-79.750 mm
-0.125 . . . . . . . . . . . . . . . . . . . . . 79.855-79.875 mm
Rear bearing diameter
Nominal . . . . . . . . . . . . . . . . . . . 80.045-80.070 mm
-0.25 . . . . . . . . . . . . . . . . . . . . . . 79.795-79.820 mm
-0.125 . . . . . . . . . . . . . . . . . . . . . 79.920-79.945 mm
Clearance between journal
and bearing: 0.045-0.090
Wear limit: 0.200 mm
Connecting rod journal
Nominal . . . . . . . . . . . . . . . . . . . . . . 53.940-53.955
-0.25 . . . . . . . . . . . . . . . . . . . . . . 53.690-53.705 mm
-0.125 . . . . . . . . . . . . . . . . . . . . . 53.814-53.830 mm
Connecting rod bearing
Nominal . . . . . . . . . . . . . . . . . . . 53.977-54.016 mm
-0.25 . . . . . . . . . . . . . . . . . . . . . . 53.727-53.766 mm
Fig. 125 Checking Rotor Clearance -0.125 . . . . . . . . . . . . . . . . . . . . . 53.852-53.891 mm
Clearance between journal
SPECIFICATIONS and bearing: 0.022-0.076
Wear limit: 0.200 mm
ENGINE SPECIFICATIONS Crankshaft end play
End play . . . . . . . . . . . . . . . . . . . . 0.080-0.280 mm
DESCRIPTION SPECIFICATIONS
Adjustment . . . . . . . . . . . . . . . . . . Thrust washers
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 CIEW
Thrust washers available: . . . . . . . . . 2.31-2.36 mm
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . 5
2.41-2.46 mm
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 mm
2.51-2.56 mm
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 mm
Main bearing carriers
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3125cc
Internal diameter
Injection order . . . . . . . . . . . . . . . . . . . . . 1-2-4-5-3
Front . . . . . . . . . . . . . . . . . . . . . 67.025-67.050 mm
Compression ratio . . . . . . . . . . . . . . . . 21 : 1(+/0.5)
Center . . . . . . . . . . . . . . . . . . . . 66.670-66.687 mm
Gasket . . . . . . . . . . . . . . . . . . . . . . . . Asbestos free
Rear . . . . . . . . . . . . . . . . . . . . . . 85.985-86.005 mm
Crankshaft
Liners
Front journal diameter
Internal diameter . . . . . . . . . . . . 91.997-92.015 mm
Nominal . . . . . . . . . . . . . . . . . . . 62.985-63.005 mm
Protrusion . . . . . . . . . . . . . . . . . . . . . 0.01-0.06 mm
-0.25 . . . . . . . . . . . . . . . . . . . . . . 62.735-62.755 mm
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . Shims
-0.125 . . . . . . . . . . . . . . . . . . . . . 62.860-62.880 mm
Available Shims: . . . . . . . . . . . . . . . . . . . . 0.15 mm
Front bearing diameter . . . . . . . . . . . . . . . . . . . . . .
0.17 mm
Nominal . . . . . . . . . . . . . . . . . . . 63.043-63.088 mm
0.20 mm
-0.25 . . . . . . . . . . . . . . . . . . . . . . 62.793-62.838 mm
0.23 mm
-0.125 . . . . . . . . . . . . . . . . . . . . . 62.918-62.963 mm
0.25 mm
Clearance between journal
Cylinder head
and bearing: 0.038-0.103 mm
Minimum thickness . . . . . . . . . . . . 89.95-90.05 mm
Center journal diameter
Gaskets thickness: . . . . 1.41 mm +/-0.08, 0 notches
Nominal . . . . . . . . . . . . . . . . . . . 63.005-63.020 mm
. . . . . . . . . . . . . . . . . . . 1.61 mm +/-0.08, 1 notches
-0.25 . . . . . . . . . . . . . . . . . . . . . . 62.755-62.770 mm
. . . . . . . . . . . . . . . . . . . 1.51 mm +/-0.08, 2 notches
-0.125 . . . . . . . . . . . . . . . . . . . . . 62.880-62.895 mm
End plates:
Center bearing diameter
Height . . . . . . . . . . . . . . . . . . . . . . 89.92-90.00 mm
Nominal . . . . . . . . . . . . . . . . . . . 63.050-63.093 mm
-0.25 . . . . . . . . . . . . . . . . . . . . . . 62.800-62.843 mm
WJ ENGINE 9 - 63
SPECIFICATIONS (Continued)
DESCRIPTION SPECIFICATIONS DESCRIPTION SPECIFICATIONS
Connecting rods Face angle:
Weight (without the crank bearing): 966 grams Intake . . . . . . . . . . . . . . . . . . . . . . . 55°308-55°408
Small end bearing Exhaust . . . . . . . . . . . . . . . . . . . . . 45°258-45°358
Internal diameter Head diameter:
Minimum . . . . . . . . . . . . . . . . . . . . . . . 30.035 mm Intake . . . . . . . . . . . . . . . . . . . . . 40.05-40.25 mm
Maximum . . . . . . . . . . . . . . . . . . . . . . . 30.050 mm Exhaust . . . . . . . . . . . . . . . . . . . . . 33.8-34.0 mm
Crankshaft bearings Head stand down:
Standard internal diameter . . . . 53.977-54.016 mm Intake . . . . . . . . . . . . . . . . . . . . . . 1.08-1.34 mm
Pistons Exhaust . . . . . . . . . . . . . . . . . . . . . 0.99-1.25 mm
Skirt diameter . . . . . . . . . . . . . . 91.918-91.932 mm Stem diameter:
(measured at approximately 10 mm above the Intake . . . . . . . . . . . . . . . . . . . . . 7.940-7.960 mm
bottom of the skirt). Exhaust . . . . . . . . . . . . . . . . . . . 7.922-7.940 mm
Piston clearance . . . . . . . . . . . . . . . 0.065-0.083 mm Clearance in guide:
Top of piston to cylinder head . . . . . . 0.80-0.89 mm Intake . . . . . . . . . . . . . . . . . . . . . 0.040-0.075 mm
Piston protrusion . . . . . . . . . . . 0.53-0.62 Fit gasket Exhaust . . . . . . . . . . . . . . . . . . . 0.060-0.093 mm
. . . . . . . . . . . . . . . . . . . . . Number (1.41), 0 notches Valve guide
. . . . . . . . . . . . . . . . . . . . . . . . . 0.73-0.82 Fit gasket Inside diameter . . . . . . . . . . . . . . . . . 8.0-8.015 mm
. . . . . . . . . . . . . . . . . . . . . Number (1.61), 1 notches Fitted height . . . . . . . . . . . . . . . . . . . . 13.5-1.4 mm
. . . . . . . . . . . . . . . . . . . . . . . . . 0.63-0.72 Fit gasket Valve springs
. . . . . . . . . . . . . . . . . . . . . Number (1.51), 2 notches Free length . . . . . . . . . . . . . . . . . . . . . . . 44.65 mm
Piston pins Fitted length . . . . . . . . . . . . . . . . . . . . . . . 38.6 mm
Type . . . . . . . . . . . . . . . . . . . . . . . . . Fully floating Load at fitted length . . . . . . . . . . . . . . 34 +/-6% Kg
Pin diameter . . . . . . . . . . . . . . . 29.992-29.996 mm Load at top of lift . . . . . . . . . . . . . . . 92.5 +/- 4% Kg
Clearance . . . . . . . . . . . . . . . . . . . . 0.004-0.012 mm Number of coils . . . . . . . . . . . . . . 5.33 Valve timing
Piston rings Lubrication
Clearance in groove: System pressure at 4000 rev/min . 3.5 to 5.0 bar (oil
Top . . . . . . . . . . . . . . . . . . . . . . . 0.080-0.130 mm at 90-100°C)
Second . . . . . . . . . . . . . . . . . . . . 0.070-0.110 mm Pressure relief valve opens . . . . . . . . . . . . 6.84 bar
Oil control . . . . . . . . . . . . . . . . . 0.040-0.080 mm Pressure relief valve spring
Fitted gap: — free length . . . . . . . . . . . . . . . . . . . . 57.5 mm
Top . . . . . . . . . . . . . . . . . . . . . . . . . 0.30-0.45 mm Oil pump:
Second . . . . . . . . . . . . . . . . . . . . . . 0.30-0.45 mm Outer rotor end float . . . . . . . . . 0.030-0.107 mm
Oil control . . . . . . . . . . . . . . . . . . . 0.25-0.50 mm Inner roter end float . . . . . . . . . . 0.030-0.107 mm
Camshaft Outer rotor to body diam.
Journal diameter, front . . . . . . . . 53.495-53.51 mm clearance . . . . . . . . . . . . . . . . . . 0.130-0.230 mm
Bearing clearance . . . . . . . . . . . . 0.030-0.095 mm Rotor body to drive gear clearance . . . . . . . . . . . . . .
Center . . . . . . . . . . . . . . . . . . . . . . 53.45-53.47 mm (pump not fitted) . . . . . . . . . . . . . . . . 0.30-0.50 mm
Bearing clearance . . . . . . . . . . . . . . 0.07-0.14 mm
Rear . . . . . . . . . . . . . . . . . . . . . . . . 53.48-53.50 mm
TORQUE SPECIFICATIONS
Bearing clearance . . . . . . . . . . . . . . 0.04-0.11 mm
DESCRIPTION TORQUE
Tappets
Adaptor Plate to Block
Outside diameter . . . . . . . . . . . . 22.195-22.212 mm
Nuts (6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m
Rocker gear
Automatic Belt Tensioner to Block
Shaft diameter . . . . . . . . . . . . . 21.979-22.00 mm
Bolts (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 N·m
Bush internal diameter . . . . . . . 22.020-22.041 mm
Automatic Belt Tensioner to Mounting Bracket
Assembly clearance . . . . . . . . . . . . 0.020-0.062 mm
Bolt (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 N·m
Valves
Generator bracket
Intake valve:
Mounting bolts (10 mm) . . . . . . . . . . . . . . . 47 N·m
Opens . . . . . . . . . . . . . . . . . . . . . . 26° B. T. D. C.
Mounting bolts (12 mm) . . . . . . . . . . . . . . . 83 N·m
Closes . . . . . . . . . . . . . . . . . . . . . . 58° A. B. D. C.
Generator
Exhaust valve:
Mounting bolt . . . . . . . . . . . . . . . . . . . . . . . 47 N·m
Opens . . . . . . . . . . . . . . . . . . . . . . 66° B. B. D. C.
Camshaft thrust plate
Closes . . . . . . . . . . . . . . . . . . . . . . . . 36° A. T. D. C.
Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m
9 - 64 ENGINE WJ
SPECIFICATIONS (Continued)
DESCRIPTION TORQUE DESCRIPTION TORQUE
Connecting rod Main bearing oil delivery
Mounting bolt . . . . . . . . . . . . . . . . . . 29.5 N·m +60° Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 N·m
Crankshaft bearing Water hose to cylinder head
Carrier screw . . . . . . . . . . . . . . . . . . . . . . . 44 N·m Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 to 10 N·m
Crankshaft pulley Oil cooler adaptor
Locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 N·m Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 N·m
Crossmember Oil feed line
Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 N·m For rocker arms . . . . . . . . . . . . . . . . . . . . . 12 N·m
Diesel delivery To block . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m
Union nut . . . . . . . . . . . . . . . . . . . . . . . . . . 19 N·m To vacuum pump . . . . . . . . . . . . . . . . . . . . . 15 N·m
EGR valve Oil filter
To intake manifold . . . . . . . . . . . . . . . . . . . 27 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 N·m
EGR tube Oil filter adapter
To EGR valve . . . . . . . . . . . . . . . . . . . . . . . 27 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . 46.6 N·m
Engine mounts Oil filter base
Engine support bracket . . . . . . . . . . . . . . . . 61 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . 46.6 N·m
Support Cushion . . . . . . . . . . . . . . . . . . . . . 47 N·m Oil pan
Support cushion bracket bolts . . . . . . . . . . . 54 N·m Mounting bolts . . . . . . . . . . . . . . . . . . . . . . 13 N·m
Support cushion bracket stud nuts . . . . . . . 41 N·m Oil pickup tube
Support Cushion through bolt . . . . . . . . . . . 65 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m
Exhaust down pipe Oil pump
To turbocharger . . . . . . . . . . . . . . . . . . . . . . 32 N·m Mounting screw . . . . . . . . . . . . . . . . . . . . . . 27 N·m
Exhaust heat shield Oil sump drain plug
Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 N·m
Exhaust manifold collar Power steering pressure hose
Mounting nut . . . . . . . . . . . . . . . . 24.5 to 29.5 N·m Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 N·m
Exhaust manifold Power steering pulley
Mounting nut . . . . . . . . . . . . . . . . . . . . . . . 32 N·m Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 N·m
Fan drive Rear crankshaft bearing carrier Allen Bolts
To fan hub . . . . . . . . . . . . . . . . . . . . . . . . . . 56 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 N·m
Flexplate adapter hub to crankshaft Rocker cover
Bolts . . . . . . . . . . . . . 1st 50 N·m2nd 20 N·m + 75° Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 N·m
Flexplate to adapter hub Rocker mounting
Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 N·m Lock Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 N·m
Front timing cover Steering pump
Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 N·m Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 N·m
Fuel filter Turbocharger
Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 N·m Mounting nuts . . . . . . . . . . . . . . . . . . . . . 32.5 N·m
Glow plug Turbocharger
Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 N·m Oil delivery fitting . . . . . . . . . . . . . . . . . . 27.5 N·m
Idler pulley Turbocharger oil drain
Bolt (left hand thread) . . . . . . . . . . . . . . . . 47 N·m Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8 N·m
Injection pump fuel lines Vacuum pump
Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 N·m Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m
Injection pump gear Water manifold
Lock nut . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 N·m Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 N·m
Injection pump Water pump pulley
Mounting nut . . . . . . . . . . . . . . . . . . . . . . 27.5 N·m Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m
Injector
Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . 68.5 N·m
Intake manifold
Mounting nut . . . . . . . . . . . . . . . . . . . . . . 32.5 N·m
WJ ENGINE 9 - 65

SPECIAL TOOLS
SPECIAL TOOLS

Injection Pump Puller and Gear retainer VM.1003

Crankshaft Pulley and Gear Remover VM.1000A

Crankshaft Remover/Installer Sleeve VM.1004

Cylinder Liner Puller VM.1001

Torque Angle Gauge VM.1005

Crankshaft Bearing Remover/Replacer VM.1002

9 - 66 ENGINE WJ
SPECIAL TOOLS (Continued)

Bosch Pump Timing Adapter VM.1011

Cylinder Head Bolt Wrench VM.1006A

Cylinder Head Guide Studs VM.1009 Injector Remover/Installer Socket VM.1012B

Cylinder Liner Protrusion Tool VM.1010

Dial Indicator Gauge VM.1013
WJ ENGINE 9 - 67
SPECIAL TOOLS (Continued)

Flywheel Locking Tool VM.1014

Crankshaft and Water Pump Pulley Holder VM.1017

Timing Cover Oil Seal Installer VM.1015A

Cylinder Head Bolt Wrench M12 VM.1018

Cylinder Head Bolt Wrench M14 VM.1019

Cylinder Retainer VM.1016

1 – VM.1016
2 – CYLINDER LINER
3 – CYLINDER BLOCK
9 - 68 ENGINE WJ
SPECIAL TOOLS (Continued)

Cylinder Leakage Tester Adapter VM.1021

Top Dead Center Tool VM.8374

Camshaft Bearing Remover/Installer VM.1040

Transmission Pilot Bushing Gauge VM.8390

Transmission Pilot Bushing Remover VM.8399

Transmission Pilot Bushing Installer VM.8372