Scribd
Upload
7K views3 pages

Cloud Buster Instructions

This document provides instructions for building a device called a Chembuster to eliminate chemtrails. It describes using a plastic bucket as the base and inserting six copper pipes that are 6 feet long and open on one end. Crystals are wrapped in copper wire and placed in the pipes without being glued. Metal particles like aluminum filings and steel wool are added. Templates are made from 3/4 inch plywood to guide drilling holes for the pipes and ensure they are evenly spaced and parallel. The completed device aims to eliminate chemtrails using orgone energy conducted through the materials.

Uploaded by

Buzzard
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
7K views3 pages

Cloud Buster Instructions

This document provides instructions for building a device called a Chembuster to eliminate chemtrails. It describes using a plastic bucket as the base and inserting six copper pipes that are 6 feet long and open on one end. Crystals are wrapped in copper wire and placed in the pipes without being glued. Metal particles like aluminum filings and steel wool are added. Templates are made from 3/4 inch plywood to guide drilling holes for the pipes and ensure they are evenly spaced and parallel. The completed device aims to eliminate chemtrails using orgone energy conducted through the materials.

Uploaded by

Buzzard
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

CHEMBUSTER DIRECTIONS

Adapted from Don Croft original instructions

BUCKET: Base: 9" in dia., 9"


deep. I use two-gallon plastic
buckets from the Home Depot
paint department, but two-gallon
food buckets, available from
restaurants, or two-gallon
spackle buckets from drywall
contractors are fine. Leave the
buckets on, as the handles make
it easier to move the finished
Chembuster.

COPPER PIPES:
Six standard Type M, 1" copper pipes, 6' long, open at one end, the capped ends
submerged to within an inch or so of the bottom of the bucket before casting. For
portability and shipping, you can use 12” sections of pipe in the base, adding five-foot
lengths by putting couplers between the 12” and five-foot pieces. You won’t need to buy as
much copper pipe this way, too.

Page 1
CRYSTALS: Do not glue Crystals in, wrap, in copper wire so that you can pull them out
and clean them later. I use 'Goop' glue. Tape, or solder around the cap where it joins the
pipe to prevent resin from leaking into the cap during casting. (Note) Another option is to
add one citrine gemstone to each pipe before adding the crystal, this smoothes the CB’s
energy and helps to transmute negative energies. However, citrine does not seem to make
the CB any more effective at eliminating chemtrails.

METAL PARTICLES: Get some metal particles from a machine shop, recycling yard or a
place where they saw a lot of aluminum (sign shops and aluminum fabrication shops are
good places to look). I use aluminum for weight considerations, but ANY metal will do.

Very fine particles (such as filings from a key-making machine) are not good as they
bunch up together and block Orgone from coming out. There really is a wide margin of
suitability! You can use Steel wool quite effectively and it is easy to buy at a hardware
shop.

PLYWOOD: Template 1 - 3/4” exterior plywood is used to make the base for the copper
endcaps/pipes. I arrange the six pipes evenly around a 2 1/2” radius circle, which makes
the pipes 2 1/2” apart on centres. A flat, 1 1/4” auger bit drills a suitable hole for each end
cap.

Template 2 - Make another piece to fit inside the rim of the bucket. Remember to cut a
section away so you can fit your fingers under it to remove it from the bucket. This piece is
not part of the finished CB, just used to get the spacing for the pipes right during
construction. Cut the holes in this with a 1 1/8” flat bit so that it will fit well over the six
pipes. This piece will hold the pipes in position while the second batch of resin hardens.

Template 3 - I make a circular plywood spacer for the top ends of the pipes, 4” radius with
1 1/8” holes on the same 2 1/2” radius circles for the pipe ends. This keeps the pipes
parallel with each other and fairly rigid.

Page 2
Do not glue the crystal in the tubes, instead, wrap
copper wire around the crystals as shown above,
then lower them inside the tubes when the Cloud
Buster is completed.

That way you can clean them when rain fills the
tubes with water.

Just make sure that the wire is long enough so it stick


about 2 cm (1 inch) above the end of the tubes so
that you can grab then to clean them up.

Page 3

You might also like