Weighing

Weighing
EWA
Service Manual

REV1

EWA
 Weighing

Power Source
100~240V 50/60hz AC INTPUT
10V/0.6A DC OUTPUT 6W
6V/4AH Lead-acid rechargeable battery included

Power Consumption
Approx. 12mA
Approx. 36mA with backlight
Approx. 48mA with backlight and RS232 interface

Battery hours per charge

Approx. 320 hours (backlight off)

OPTION
RS232 Interface

LOADCELL connection (for indicator)

PIN1 : E + PIN2 : E- PIN3 : S+ PIN4 : S- PIN5 : GND

How to display version number?

Turn on the scale and press and hold the M+/PRINT/ ↵ key until the
countdown sequence has completed. The LCD display will show 11 .The
shown number is the software version of the scale. Release the key and
the scale will off.

Display

EWA 1
 Weighing

Key description

OFF key:
Press and hold the OFF key and the display will show “oFF＂ for 2 seconds
then the scale will turn off automatically.
ON/ZERO/ ▶ key:
Press the ON key to turn on the scale. The scale will start self-adjusting
sequence then will stabilize in 0.
ZERO : To reset the weight to 0, but the displayed weight value has to
be less than ± 2% of maximum capacity.
▶ : To move one space to the right or upward in setup mode.
To the right
000000 → 000000 → 000000 → 000000 → 000000 → 000000
Upward
LF 1 → LF 2 → LF 3 → …… → LF 8
UF-1 → UF-2 → UF-3→ ……→ UF-9
ECF-1 → ECF-2 → ECF-3
UNITS / ESC key:
UNITS: To select desired weighing unit.
When change into PCS，PCS marker light，Optional number by ▲
switch: 10、20、50、100、200，put the corresponding number of objects
on the scale,after the stable press ↵ key, complete the number of
samples.
ESC : To escape (exit) setting in setup mode.
TARE / ◀ key:
TARE : To subtract the container weight. Maximum tare = full capacity
◀ : To move one space to the left or downward in setup mode.
To the left
000000 → 000000 → 000000 → 000000 → 000000 → 000000
Downward
LF 8 → LF 7 → LF 6 → …… → LF 1
UF-9 → UF-8 → UF-7→ ……→ UF-1
ECF-3 → ECF-2 → ECF- 1
MR/MC / ▲ key:
MR: To display total accumulation count and total accumulated weight
EWA 2
 Weighing

MC : Memory Clear key to clear all accumulated weight data (When the
weighing unit is changed (ex: from kg to lb), all accumulated data
will be cleared automatically) (display cursor M+ lights off)
▲ : To increase values upward in setup mode.
例如 : 232 0 → 232 1 → 232 2 → 232 3 → …… → 232 6
M+/PRINT / ↵ key:
Accumulation key: The M+ key can be used to accumulate weight, when display
above 999999,can not to the next accumulate.
PRINT : Manually transmitting data through RS232 to computer or printer
at normal weighing mode (RS232 setup must be set at keyboard
transmission 232 3 or 232 6)
↵ : Works as enter key in setup mode

※ Error messages:
Err N Unstable internal count
-OL- Overload, when the weight is heavier than the full capacity
+ 9d of the scale

Functions Setup
Approval Calibrations and Functions Setup (Lock section) L F 1 ~ 8
Standard Functions Setup UF – 1 ~ 9
Standard Calibrations ECF – 1 ~ 3

Standard Calibrations:
Press the TARE/ ◀ key and the M+/PRINT /↵ key in weighing mode to
start Standard Calibrations
ECF-1 Weight Calibration (Zero and Span)
ECF-2 Zero Calibration
ECF-3 Span Calibration
※ When the scale is programmed for Approval (LF 6), standard
calibration will be locked

ECF-1 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
EWA 3
 Weighing

↑↓
◀ ▶
ECF-2 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
ECF-3 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode

ECF-1 Weight Calibration :

ECF-1 Press the ↵ key to start Weight Calibration (Press

the ESC key to exit back to weighing mode)
↓
↵
CALZ Press the ↵ key to calibrate zero point (Press the
ESC key to terminate calibration back to menu ECF-1)
↓
↵
150.00kg Use ◀,▶,▲ and then ↵ key to enter the weight to be
calibrated
↓ (Press the ESC key to terminate calibration back to
↵ menu ECF-1)
150.00kg Place the required weight mass onto the scale as
indicated on display and press the ↵ key to calibrate
the scale
↓ (Press the ESC key to terminate calibration back to
↵ menu ECF-1)
150.00kg Calibration procedure completed and the scale will
return back to weighing mode automatically

ECF-2 Zero Calibration :

ECF-2 Press the ↵ key to start Zero Calibration (Press the
ESC key to exit back to weighing mode)
↓
EWA 4
 Weighing

↵
CALZ Press the ↵ key to calibrate zero point (Press the
ESC key to terminate calibration back to menu ECF-2)
↓
↵
0.00kg Zero Calibration procedure completed and the scale
will return back to weighing mode automatically

ECF-3 SPAN Calibration :

ECF-3 Press the ↵ key to start Span Calibration (Press the
ESC key to exit back to weighing mode)
↓
↵
150.00kg Use ◀,▶,▲ and then ↵ key to enter the weight to be
calibrated
↓ (Press the ESC key to terminate calibration back to
↵ menu ECF-3)
150.00kg Place the required weight mass onto the scale as
indicated on display and press the ↵ key to calibrate
the scale
↓ (Press the ESC key to terminate calibration back to
↵ menu ECF-3)
150.00kg Calibration procedure completed and the scale will
return back to weighing mode automatically

Standard Functions Setup :

Press the ON/ZERO/ ▶ and the M+/PRINT /↵ key in weighing mode to
start Standard Functions Setup
UF-1 Internal Value
UF-2 Check Weighing
UF-3 Auto Power-off
UF-4 Backlight
✤UF-5 Hold
UF-6 RS232 Output

EWA 5
 Weighing

✤UF-7 ADC Update Rate

✤UF-8 Display Condition at Zero
UF-9 Gravitational (G value) Pre-Calibration
✤ marks function locked when LF 6 is set as “Approval Version＂
UF-1 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-2 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-3 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-4 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-5 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-6 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-7 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-8 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↑↓
◀ ▶
UF-9 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode

UF-1 Internal Value:

UF-1 Press the ↵ key to see the internal value or press

EWA 6
 Weighing

the ESC key to exit menu and back to weighing mode

↓ ↵
2704565 Press the ↵ key to continue or the ESC key to exit
back to menu UF-1
↓ ↵
Press the ↵ key to see the battery voltage or the ESC
bAt469 key to exit back to menu UF-1

UF-1 Use ▶ and then ↵ keys to continue with other setups

or press the ESC key to exit menu and back to weighing
mode

UF-2 Check Weighing :

0000.0L Set LO (low) weight

0000.0H Set HI (high) weight
O 000 Program I/O conditions
※ LO set as 0 will clear all check weigh values
※ Check weighing conditions can be set independently for each of the
weighing units and counting mode
※ All settings will be saved until manually cleared
※ Last entry will be displayed before setup
※ This function is locked when UF-5 is set as “HOLD 1＂
UF-2 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
0000.0L Use ◀,▶,▲ and then ↵ key to set LO weight value
↓ (Press the ESC key to exit the setup and back to menu
↵ UF-2)
0000.0H Use ◀,▶,▲ and then ↵ key to set HI weight value
↓ (Press the ESC key to exit the setup and back to menu
↵ UF-2)

EWA 7
 Weighing

O 000 Use ◀,▶,▲ and then ↵ key to set I/O SET value
↓ (Press the ESC key to exit the setup and back to menu
↵ UF-2)
UF-2 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-3 Auto Power-off :

AoFF 00 Auto power-off disable

AoFF 01 The scale turns off automatically in 1 minute when the scale
s
not in operation and weight at 0
Auto power-off timer up to 99 minutes (AoFF01~AoFF 99)
※ Factory default: AoFF 10

UF-3 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
AoFF10 Use ◀﹑▶﹑▲ and then ↵ key to enter Auto Power-off
time
↓ (Press the ESC key to exit the setup and back to menu
↵ UF-3)
UF-3 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-4 Backlight :

Lit oFF :Backlight off Lit A :Auto light up Lit on :Backlight

on
※ Factory default: Lit A

UF-4 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
EWA 8
 Weighing

Lit A Use ▲ and then ↵ key to select backlight modes

(Press the ESC key to exit the setup and back to menu
UF-4)
↓
↵
UF-4 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-5 Hold :
HOLD 0 Hold function off
HOLD 1 Animal (motion) Hold function
PCt XXX To set the range from 001 ~ 100 of the animal hold
(for HOLD 1 only)
timEXX To set 1﹑﹑2﹑﹑4﹑﹑8﹑﹑16﹑﹑32﹑﹑64 times within the hold range
(for HOLD 1 only)
※ This function is locked when LF 6 is set as “Approval Version＂
※ Factory default: HOLD 0

UF-5 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
HOLD 0 Use ▲ and then ↵ key to select Hold modes
(Press the ESC key to exit the setup and back to menu
UF-5)
↓
↵
UF-5 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

HOLD 1 mode :
UF-5 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode

EWA 9
 Weighing

↓
↵
HOLD 1 Use ▲ and then ↵ key to select Hold 1 mode
(Press the ESC key to exit the setup and back to menu
UF-5)
↓
↵
PCt 010 Use ◀﹑▶﹑▲ and then ↵ key to enter the hold range
(Press the ESC key to exit the setup and back to menu
UF-5)
↓
↵
timE 8 Use ▲ and then ↵ key to select times
(Press the ESC key to exit the setup and back to menu
UF-5)
↓
↵
UF-5 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-6 RS232 :
232 0 RS232 disable
232 1 Stable output – Format 1
232 2 Stream output – Format 1
232 3 Manual output – Format 1
232 4 Stable output – Format 2
232 5 Stream output – Format 2
232 6 Manual output – Format 2
RS232 Baud rate
b 1200 Baud rate 1200
b 2400 Baud rate 2400
b 4800 Baud rate 4800
b 9600 Baud rate 9600

EWA 10
 Weighing

b19200 Baud rate 19200

b38400 Baud rate 38400

Communication Protocol
UART signal of EIA-RS232 C
Format：
1. Serial output: 1200 / 2400 / 4800 / 9600 / 19200 / 38400 BPS
2. Data bits : 8 BITS
3. Parity bits : None
4. Stop bits : 1 BIT

Start bit Data bits Stop bits

Format 1 (232 1 ~ 3 ) :
HEAD1 ( 2 BYTES ) HEAD2 ( 2 BYTES )
OL - Over Load
ST - Stable NT - Net Weight
US - Unstable GS - Gross Weight

Fixed 18 BYTES ASCII (kg g t lb)

1 2 1 1 2 1 1 2 3 4 5 6 7 8 1 2 1 2

HEAD1 , HEAD2 , DATA UNIT CR LF

Fixed 21 BYTES ASCII (tl.T lboz)

1 2 1 1 2 1 1 2 3 4 5 6 7 8 9 1 2 3 4 1 2

HEAD1 , HEAD2 , DATA UNIT CR LF

Fixed 19 BYTES ASCII (pcs)

1 2 1 1 2 1 1 2 3 4 5 6 7 8 1 2 3 1 2

HEAD1 , HEAD2 , DATA UNIT CR LF

Output examples :
1. Example +0.876 kg Stable net weight :
S T , N T , + 0 0 0 . 8 7 6 k g 0D 0A

2. Example -1.568 lb unstable gross weight :

U S , G S , - 0 0 1 . 5 6 8 l b 0D 0A

EWA 11
 Weighing

3 Example -20. 5.40 lb oz unstable gross weight :

S T , G S , - 1 0 ﹒ 0 5 ﹒ 4 0 l b o z 0D 0A

4 Example +1000 pcs stable net weight :

S T , N T , + 0 0 0 1 0 0 0 p c s 0D 0A

Format 2 (232 4 ~ 6) :
Fixed 12 BYTES ASCII (kg g t lb)
1 2 3 4 5 6 7 8 1 2 1 2

DATA UNIT CR LF
Fixed 15 BYTES ASCII (tl.T lboz)
1 2 3 4 5 6 7 8 9 1 2 3 4 1 2

DATA UNIT CR LF
Fixed 13 BYTES ASCII (pcs)
1 2 3 4 5 6 7 8 1 2 3 1 2

DATA UNIT CR LF
Output examples :
1. Example +0.876 kg stable net weight :
+ 0 0 0 . 8 7 6 k g 0D 0A

2. Example -1.568 lb unstable gross weight :

- 0 0 1 . 5 6 8 l b 0D 0A

3 Example -20. 5.40 lb oz unstable gross weight :

- 1 0 ﹒ 0 5 ﹒ 4 0 l b o z 0D 0A

4 Example +1000 pcs stable net weight :

+ 0 0 0 1 0 0 0 p c s 0D 0A

※ Factory default: 232 0

UF-6 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
232 0 Use ▲ and then ↵ key to enter RS232 output format
(Press the ESC key to exit the setup and back to menu
UF-6)
↓
EWA 12
 Weighing

↵
b 9600 Use ▲ and then ↵ key to select baud rate
(Press the ESC key to exit the setup and back to menu
UF-6)
↓
↵
UF-6 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-7 ADC Update Rate :

SPEEd 1 Standard speed 15 hz
SPEEd 2 High speed 30 hz
SPEEd 3 Low speed 7.5 hz
※ This function is locked when UF-5 is set as “HOLD 1＂
※ This function is locked when LF 6 is set as “Approval Version＂
※ Factory default: SPEEd 1

UF-7 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
SPEEd 1 Use ▲ and then ↵ key to select ADC speed
(Press the ESC key to exit the setup and back to menu
UF-7)
↓
↵
UF-7 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-8 Zero Weight Display Condition :

ZP 0 Off
ZP 1 One division not to display at zero
ZP 2 Two divisions not to display at zero

EWA 13
 Weighing

ZP 3 Three divisions not to display at zero

ZP 4 Four divisions not to display at zero
ZP 5 Five divisions not to display at zero
※ This function is locked when UF-5 is set as “HOLD 1＂
※ This function is locked when LF 6 is set as “Approval Version＂
※ Factory default: ZP 0

UF-8 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
ZP 0 Use ▲ and then ↵ key to select how many divisions
not to display at zero
(Press the ESC key to exit the setup and back to menu
UF-8)
↓
↵
UF-8 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

UF-9 Standard Gravitational (G value) Pre-Calibration:

Approval Model: When the CAL switch is at OFF, 10 gravitational values

can be entered and can be also recalled for reference. After 10
gravitational values have been filled, the scale will only allow
recalling previous 10 values (-00- ~ -09-) for reference and adding new
value will not be allowed. Internal Gravitational Calibration or LF1
Internal Weight Calibration has to be done to erase previously entered
values.
Non-approval Model: Even the scale allows to do the Standard
Calibration, Gravitational Calibration can help to provide accurate
scale when end users received it without all the trouble to recalibrate
the scale. Pre-calibration is allowed when the scale is setup as
non-approval model or the CAL switch is at ADJ position. Gravitational
value will be saved at -00- and will be replaced each time a new value

EWA 14
 Weighing

has been entered.

※ Sender G value: Set it before Weight Calibration
※ Recipient G value: Set it after Weight Calibration
※ The G value will be denied when the value is greater than 9.83217
(Polar G value) or less than 9.78031 (Equator G value)
※ Factory Default: 9.79423

UF-9 Press the ↵ key to start or press the ESC key to exit
menu and back to weighing mode
↓
↵
-03- The display will show the last value for 1 second
↓
9.79423 Use ◀﹑▶ keys to see previous entered values. The
display will stay at 00 if no value has been entered
↑↓ ▶
◀
-02- The display will show the last value for 1 second
↓
9.79585 Use ◀﹑▶ keys to see previous entered values. The
display will stay at 00 if no value has been entered
↓ Press the ↵ key to start
↵ (Press the ESC key to exit the setup and back to menu
UF-9)
9.79585 Use ◀﹑▶﹑▲ and then ↵ key to enter the G value
(Press the ESC key to exit the setup and back to menu
UF-9)
↓
↵
9.79423 Press the ↵ key to confirm the G value
↓
↵
UF-9 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and back to weighing
mode

EWA 15
 Weighing

Approval Calibrations and Functions Setup (Lock section):

Turn on the scale and press and hold the ON/ZERO/ ▶ key until the scale
will show LF 1
LF 1 Weight Calibration
LF 2 Spec Calibration
LF 3 Linearity Calibration
LF 4 ADC Update Speed
LF 5 Zero Weight Display Condition
LF 6 Approval Conformity
LF 7 Gravitational (G value) Pre-Calibration
LF 8 Zero Weight Display Condition
※ CAL switch has to be ON
※ Password is required to use Lock Section when LF 6 is set as “none＂
and CAL switch is OFF

EWA 16
 Weighing

P 0000 Use ◀﹑▶﹑▲ and then ↵ key to enter the password

↓
P 0020 Press the ↵ key to enter lock section setup
↓
↵
LF 1 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically
↑↓
◀ ▶
LF 2 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically
↑↓
◀ ▶
LF 3 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically
↑↓
◀ ▶
LF 4 Press the ↵ key to start or press the ESC key to
exit menu and back to weighing mode
↑↓
◀ ▶
LF 5 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically
↑↓
◀ ▶
LF 6 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically
↑↓
◀ ▶
LF 7 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically
↑↓
◀ ▶
LF 8 Press the ↵ key to start or press the ESC key to
exit menu and the scale will restart automatically

LF 1 Weight Calibration :

※ Calibration can be done with any weight, but the weight should not
be less than 1/100 of the max. capacity and not to exceed the max.
capacity

LF 1 Press the ↵ key to start or press the ESC key to exit

EWA 17
 Weighing

menu and the scale will restart automatically

↓
↵
CAL Z Press the ↵ key to start Zero Calibration
(Press the ESC key to terminate calibration back to
menu LF 1)
↓
↵
150.00 kg Use ◀﹑▶﹑▲ and then ↵ key to enter the weight to be
calibrated
(Press the ESC key to terminate calibration back to
menu LF 1)
↓
↵
150.00 kg Place the required weight mass onto the scale as
indicated on display and press the ↵ key to calibrate
the scale
(Press the ESC key to terminate calibration back to
menu LF 1)
↓
↵
150.00 kg Calibration procedure completed and the scale will
return back to weighing mode automatically

LF 2 Spec Calibration:

First step
2 6 2 1 4 4 Display Internal Value
Second step
1 0 0 0 0 1
A B C D E F
A : Metric System 0 : None 1 : kg 2 : T 3 : g
B : American System 0 : None 1 : lb 2 : lb oz
C : Other Units 0 : None 1 : TW Kg 2 : HK Kg 3 : VISS

EWA 18
 Weighing

D : PCS 0 : Off
1 : On
E : Duo range 0 : Off
1 : MULTI INTERVAL
2 : MULTIRANGE
F : Calibration Unit 1 : Metric units as calibration unit
2 : American units as calibration unit
※ lb oz unit cannot be selected as calibration unit
※ The scale will not allow to continue to the next setup step if an
error has occurred during the programming
Third step
000000kg Use ◀﹑▶﹑▲ and then ↵ key to enter the max. capacity
Showing the calibration unit
Forth step
d 0.0 Use ◀﹑▶ keys to move the position of the decimal point
d 0.00
d 0.000
d 0.0000
0.00000
Fifth step
div 01 Press the ▲ key to select division
div 02
div 05
div 10
div 20
div 50
※ After entering LF 2, the scale will display the last saved setup.
All steps have to be completed to save the changes, otherwise the
scale will keep the last setup
※ Proceed with Weight Calibration after LF2 Spec Calibration

LF 2 Press the ↵ key to start and will display the

internal value or press the ESC key to exit menu and
the scale will restart automatically
↓
EWA 19
 Weighing

↵
262144 Press the ↵ key to continue with the setup
(Press the ESC key to exit the setup and back to menu
LF 2)
↓
↵
100001 Use ◀﹑▶﹑▲ and then ↵ key to select weighing units
↓ (Press the ESC key to exit the setup and back to menu
↵ LF 2)
000000kg Use ◀﹑▶﹑▲ and then ↵ key to enter the max. capacity
↓ (Press the ESC key to exit the setup and back to menu
↵ LF 2)
d 0.0kg Use ◀﹑▶ and then ↵ key to move the decimal point
(Press the ESC key to exit the setup and back to menu
LF 2)
↓
↵
div 01 Use ▲ and then ↵ key to select division
(Press the ESC key to exit the setup and back to menu
LF 2)
↓
↵
LF 2 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

LF 3 Linearity Calibration :

Up to six calibration sections W0 ~ W6

Be sure that the scale pan is empty before start the calibration. Press
▶ key for first calibration point. Previously saved calibration point
will be erased and the display will show CLEAr
Press the ▶ key to proceed to the next calibration point
Press the ◀ key to return back to the previous calibration point
Press the ↵ key to save the calibration

EWA 20
 Weighing

Press the ESC key to terminate calibration back to menu LF 3

Suggest that the correction value is greater than max. capacity to
ensure the measuring range is within linearity range
Suggest the linearity calibration should be in three points 0 ﹑ 1/3 ﹑
2/3 ﹑ 1
※ Proceed with Weight Calibration after Linearity Calibration

LF 3 Press the ↵ key to start or press the ESC key to exit

menu and the scale will restart automatically
↓
↵
W 0 Press the ▶ key to calibrate zero (Press the ESC key
to terminate calibration back to menu LF 3)
◀ ↑↓ ▶
W 1 Place 1/3 weight mass of full capacity onto the scale
and press the ▶ key to calibrate 1/3 of the capacity
◀ ↑↓ ▶ (Press the ESC key to terminate calibration back to
menu LF 3)
W 2 Place 2/3 weight mass of full capacity onto the scale
and press the ▶ key to calibrate 2/3 of the capacity
◀ ↑↓ ▶ (Press the ESC key to terminate calibration back to
menu LF 3)
W 3 Place weight mass of full capacity onto the scale and
press the ▶ key to calibrate full capacity 放
◀ ↑↓ ▶ (Press the ESC key to terminate calibration back to
menu LF 3)
W 4 Press the ↵ key to complete linearity calibration
↓ (Press the ESC key to terminate calibration back to
↵ menu LF 3)
LF 3 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

LF 4 ADC Update Rate :

SPEEd 1 Standard speed 15 hz

EWA 21
 Weighing

SPEEd 2 High speed 30 hz

SPEEd 3 Low speed 7.5 hz
※ This function is locked when UF-5 is set as “HOLD 1＂
※ Factory default: SPEEd 1

LF 4 Press the ↵ key to start or press the ESC key to exit

menu and back to weighing mode
↓
↵
SPEEd 1 Use ▲ and then ↵ key to select ADC speed
(Press the ESC key to exit the setup and back to menu
LF 4)
↓
↵
LF 4 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

LF 5 Zero Weight Display Condition :

ZP 0 Off
ZP 1 One division not to display at zero
ZP 2 Two divisions not to display at zero
ZP 3 Three divisions not to display at zero
ZP 4 Four divisions not to display at zero
ZP 5 Five divisions not to display at zero
※ This function is locked when UF-5 is set as “HOLD 1＂
※ Factory default: ZP 0

LF 5 Press the ↵ key to start or press the ESC key to exit

menu and the scale will restart automatically
↓
↵
ZP 0 Use ▲ and then ↵ key to select how many divisions
not to display at zero
(Press the ESC key to exit the setup and back to menu
LF 5)

EWA 22
 Weighing

↓
↵
LF 5 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

LF 6 Approval Conformity:

nonE Non-approval version; Initial Zero not restricted, Standard

calibration allowed
oiML EC approval; Initial Zero FULL SCALE ±10%, Manual Zero FULL
SCALE ±2%, No standard calibration allowed
※ Factory default: nonE

LF 6 Press the ↵ key to start or press the ESC key to exit

menu and the scale will restart automatically
↓
↵
nonE Use ▲ and then ↵ key to select approval or
non-approval
(Press the ESC key to exit the setup and back to menu
LF 6)
↓
↵
LF 6 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

LF 7 Internal Gravitational (G value) Pre-Calibration:

※ Sender G value: Set it before Weight Calibration

※ Recipient G value: Set it after Weight Calibration
※ The G value will be denied when the value is greater than 9.83217
(Polar G value) or less than 9.78031 (Equator G value)
※ Factory Default: 9.79423
LF 7 Press the ↵ key to start or press the ESC key to exit

EWA 23
 Weighing

menu and the scale will restart automatically

↓
↵
-00- The display will show the number of pre-calibration
for a second
↓
9.79423 Press the ↵ key to continue
↓
↵
9.79423 Use ◀﹑▶﹑▲ and then ↵ key to enter the G value
↓ (Press the ESC key to exit the setup and back to menu
↵ LF 7)
LF 7 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

LF 8 Initial Zero:

SEtZ Y Reset zero point every time the scale has been switched on
SEtZ n Zero point reset off
※ Factory Default: SEtZ Y

LF 8 Press the ↵ key to start or press the ESC key to exit

menu and the scale will restart automatically
↓
↵
SEtZ Y Use ▲ and then ↵ key to select initial zero mode
(Press the ESC key to exit the setup and back to menu
LF 8)
↓
↵
LF 8 Use ◀﹑▶ and then ↵ key to continue with other setups
or press the ESC key to exit menu and the scale will
restart automatically

EWA 24