Technical Specification
07511-2
2007-05-01
Sandvik DP1100
DP 1100
APPLICATION
Sandvik DP1100 is a hydraulic, self-propelled, self- All panel sections can be opened for easy access to
contained, crawler based surface drilling rig service spots. Powerpack is mounted crosswise at
equipped with a cabin and a rod changer. It drills 89 - the rear of the rig to balance the weight of the boom
140 mm (3 ½" - 5 ½") vertical, inclined or horizontal and the feed.
holes with 51 mm and 60 mm (2" and 2 3/8") DP1100 has an ergonomic and roomy full vision
extension rods or 102 - 140 mm (4" - 5 ½") vertical, cabin to increase operator's comfort and efficiency.
inclined or horizontal holes with 76 and 87 mm (3" The cabin is certified for F.O.P.S. and R.O.P.S.
and 3 ½") tubes. Good results in difficult ground (Falling Object Protection Structure and Roll-Over
conditions are obtained by using pilot tube drilling, Protection Structure). Windows are safety laminated
where the first rod is replaced by a 76 or 87 mm (3" and the noise level in the cabin is less than 80 dB(A).
or 3 ½") special tube. Optimal visibility to the drilling spot is achieved by
DP1100 is equipped with HL 1010, hydraulic top locating all controls on seat arm rests and side
hammer rock drill. With high rotation torque, proper panels of the cabin. Drilling functions are
flushing and sophisticated, ergonomic Rock Pilot proportionally controlled by one joystick on right
control system the rig adapts itself easily into varying hand side. Rod changer functions are controlled by
rock conditions. The rig has a telescopic boom for another joystick on left-hand side. Cabin exceeds all
fast hole spotting and set up of the feed. The cylinder standards for operator's working environment.
feed for max. 6,1 m (20 ') starter rod for single pass DP1100 is designed for efficient production drilling in
drilling together with carousel type rod changer with medium large to large quarries or open pit mines and
a possibility to use 4,3 m (14 ') rods add productivity construction work sites. It suits well also for wall
of drilling. control and development works. To customize the rig
The powerpack of DP1100 consists of Caterpillar it can be equipped with a variety of options to meet
diesel engine and a gearbox, which divides the special requirements.
power for hydraulic pumps (two variable
displacement pumps) and flushing air compressor.
© 2007 Sandvik Mining and Construction 1/4
Technical Specification
07511-2
2007-05-01
Sandvik DP1100
COVERAGE AREA
Vertical drilling
Vertical
drilling
Horizontal Horizontal
drilling, drilling,
sideways forwards
1m
1m
DIMENSIONS
9655
2630
4010
8025
2010
900
3030
2490
© 2007 Sandvik Mining and Construction 2/4
Technical Specification
07511-2
2007-05-01
Sandvik DP1100
HYDRAULIC ROCK DRILL DUST COLLECTION SYSTEM
Rock drill type HL 1010 Dust collector type DC 1550
Drill rod diameters 51, 60 mm Capacity/vacuum 35 m3/min at 1200 mm
Drill tube diameters 76, 87 mm vacuum H2O
Operating pressure 90-160 bar Filter elements/material 20 pcs/fiber
Percussion rate 33-35 Hz Total filter surface 16 m2
Hydraulic motor output 18 kW
Percussion output power 25 kW
Primary cyclone PE 80
Maximum rotation torque 1 780 Nm
Movable suction head PE 100 S
Shank lubrication Air / oil mist
Weight 290 kg
Flushing Air
Weight 290 / 300 kg
POWERPACK
Engine type Caterpillar C 9
CYLINDER FEED
Number of cylinders 6
Feed type LF 1514 Engine output 224 kW/2 100 rpm
Length of feed 8 025 mm Transmission type Gear box
Rock drill travel 5 580 mm
Hydraulic pumps Variable/gear
(w/o hose reel)
Max. length of starter rod 6 100 mm (20') Screw compressor type Enduro 25
(w/o hose reel) Air flushing capacity 14 m3/min
Feed/pull out force 36 kN Flushing air pressure up to 10 bar
Retaining centralizer Pito 15H Air cleaner 2 pcs, dry type with
Feed extension travel 1 480 mm ejector and safety
Feed swing -56/+52° (-20/+94°) element
Feed tilt 11-133° Fuel tank 520 l
Weight 1 360 kg Fuel saving system Standard
Weight 1 350 kg
ROD CHANGER CONTROL SYSTEM
Rod changer type RC 1514 Tamrock Load sensing
Storage capacity (51 mm) 7+1 rods Collaring system Standard
Rod length 3 660, 4 270 mm Antijamming system Hydraulic / electric
Max. hole length (51 mm) 35 m (7x14’ + 1x20’) Voltage 24 VDC
Weight without rods 500 kg
OPERATOR’S CABIN
TELESCOPIC BOOM Certificates F.O.P.S. and R.O.P.S.
Boom type ZB 1550 H Noise level in the cabin 80 dB (A)
Boom extension 500 mm Controls Drilling and tramming
Boom lift +50/-17° Heaters Standard
Boom swing (left/right) +2/-27° Pressurization Standard
Drilling coverage on flat 1.6 m2 Seat Multiposition
Collaring height +1.15 /-3.5 m Vibration dampening Standard
Horizontal holes Sideways
Windows Safety laminated, tinted,
with wiper
CARRIER
Track type FL 6 HYDRAULIC SYSTEM
Grouser plate width 310 mm
Ground contact length 2 520 mm Filtration rate 12 micron abs.
Ground pressure 1.2 kg/cm2 Cooling capacity up to +50°C ambient
Ground clearance 400 mm Hydraulic oil tank 420 l
Oscillation angles +/- 11° Shank lubrication device SLU 18-1
Tramming force 140 kN
Tramming speed 1.7/3.5 km/h
© 2007 Sandvik Mining and Construction 3/4
Technical Specification
07511-2
2007-05-01
Sandvik DP1100
STANDARD COMPONENTS THE JAWS FOR DRILL STEELS
1. Rock drill HL 1010, hydraulic Drill steel type Drill steel Recommended
2. Feed LF 1514 diameter hole diameter
3. Rod changer RC 1514
1. Extension rods 51 mm 89 - 127 mm
4. Boom ZB 1550 H, telescopic
/ MF rods 2" 3 ½" - 5"
5. Carrier FL 6, oscillating
6. Powerpack Diesel driven, 2. MF-rods 60 mm 102 - 140 mm
hydraulic pumps and 2 3/8" 4" - 5 ½"
on board compressor 3. Pilot tube 76 mm 89 - 127 mm
7. Hydraulic Load sensing and 3" 3 ½" - 5"
system open center 4. 87 mm
Pilot tube 102 - 140 mm
8. Control system THC Pro with Rock Pilot 4" - 5 ½"
3 ½"
9. Operator's Ergo Pro
5. Tubes 76 mm 89 - 140 mm
cabin
10. Dust collection DC 1520 H, hydraulic 3" 3 ½" - 5½"
system 6. Tubes 87 mm 102 - 140 mm
11. Working lights 8 pcs 3 ½" 4" - 5 ½"
12. Gauge set For accumulator pressure
checking
13. Reversing alarm ADJUSTMENT INFORMATION FOR DELIVERY
14. Manuals Service and spare parts Rotation motor
manuals:
2 x paper copy 1. Rotation motor OMT 400
for 76 - 127 mm, 3" - 5" holes
2 x CD-ROM (Toolman)
2. Rotation motor OMT 500
15. EU-safety devices
for 127 - 152 mm, 5" - 6" holes
TRANSPORT DIMENSIONS Extension rod lengths
Weight 18 800 kg 1. 3 660 mm 12’
Width 2.52 m 2. 4 270 mm 14’
Height 3.2 m
Total length 10.5 m
SELECTION OF OPTIONS
1. Heating and air conditioning 21. Tube drilling kit
2. Rod greasing 22. Movable drill steel support
3. P&Q electric angle indicator 23. Horizontal drilling kit (includes hose reel)
4. Electric angle indicator TIM 2302 24. Towing hook
5. Measuring system TIM 2303 25. Readyness for Power extractor
6. Laser based measuring system TIM 2305 26. Extra manuals
7. Power extractor 27. First service kit for DP1100
8. Electric filling pump for refuelling 28. Special tools for HL 1010, field kit
9. Remote control box & hydraulic winch (7 tons) 29. Special tools for HL 1010, complete
10. Rollers for rod changer RC 1514 30. Central lubrication system
11. Hose reel 31. Fast fill connection for fuel and water tanks
12. Three-bar grouser plates 32. Fast fill connection for engine coolant,
13. Guides for grousers hydraulic oil, engine oil
14. Flushing control automatics 33. Sanrock Mini H hydraulic bit grinder
15. Shut-down of suction for water holes 34. Radio and CD player
16. Water injection system 35. Biogradeable hydraulic oil, Shell naturelle HFE
17. Water injection system w/o tank 46 or HFE 68 (synthetic ester)
18. Hydraulic ground support HM 75 36. Antifreeze for air lines
19. Fuel heater for cabin, hydraulic oil and engine
20. Kit for alternative steels
Sandvik Mining and Construction reserves the right to change this specification without further notice.
Sandvik Mining and Construction Oy
P.O.Box 100, FIN–33311 Tampere, Finland
Tel. +358
© 2007 205 44Mining
Sandvik 121, Telefax +358 205 44 4771
and Construction 4/4
www.sandvik.com
