TEO 1-2-4

REO/REO E 1-2
433.92 Mhz

D811166 15-06-01 Vers. 04

SUPERACTIVE
RADIO CONTROLS
433.92 MHZ
FREQUENCY
 TEO 1-2-4 / REO/REO F 1-2 433.92 Mhz
Thank you for buying this product, our company is sure that you will be more -Dimensions :Look fig.1
than satisfied with the product s performance. The product is supplied with -Transmitter versions:
a Warnings leaflet and an Instruction booklet . These should both be TEO1 single-channel with single coding.
read carefully as they provide important information about safety, installation, TEO2 twin channel with single coding.
operation and maintenance. This product complies with the recognised TEO4 four-channel with single coding.
technical standards and safety regulations. We declare that this product is
in conformity with the following European Directives: 89/336/EEC (and 3) TECHNICAL FEATURES OF THE RECEIVER
subsequent amendments). -Reception frequency :433.92Mhz
-Power supply :12 to 28Vdc - 16 to 28Vac
1) GENERAL SAFETY -Antenna inpedance input :52 OHM (cable RG58)
WARNING! An incorrect installation or improper use of the product -Relay contact :1A-33Vac, 1A 24Vac
can cause damage to persons, animals or things. -Working temperature :-20 +55 °C
¥ The Warnings leaflet and Instruction booklet supplied with this -Coding by :10 DIP-SWITCH
product should be read carefully as they provide important information -Number of combinations :1024 for channel
about safety, installation, use and maintenance. -Recriver versions:
¥ Scrap packing materials (plastic, cardboard, polystyrene etc) according REO1- single-channel with single coding.
to the provisions set out by current standards. Keep nylon or polystyrene REO2- twin-channel with single coding.
bags out of children s reach.
¥ Keep the instructions together with the technical brochure for future 4) ANTENNA INSTALLATION
reference. - Only use an antenna tuned to 433Mhz .
¥ This product was exclusively designed and manufactured for the use - For the ANTENNA-RECEIVER connection use RG58 coaxial cable.
specified in the present documentation. Any other use not specified in - The presence of metallic objects next ti the antenna can disturb the radio
this documentation could damage the product and be dangerous. receptor. If the transmitter has insufficient range, move the antenna to
¥ The Company declines all responsibility for any consequences resulting a more suitable position.
from improper use of the product, or use which is different from that
expected and specified in the present documentation. 5) SETTING OF CODING
¥ Do not install the product in explosive atmosphere. The coding of transmission code is set by means of the 10 path DIP
¥ The construction components of this product must comply with the SWITCH which is present in all the transmitters. This coding must coincide
following European Directives: It complies with the 89/336/EEC, with the one set in the 10 path DIP SWITCH present on the receiver (fig.2).
European Directive and subsequent amendments. As for all non-EEC
countries, the above-mentioned standards as well as the current national 6) TRANSMISSION TEOx-REOx CHANNEL SELECTION
standards should be respected in order to achieve a good safety level. The 4 path DIP-SWITCH present in the receiver, allows the changing of the
¥ The Company declines all responsibility for any consequences resulting address for activating the transmission channel out of the four available
from failure to observe Good Technical Practice when constructing (fig.3-4).
closing structures (door, gates etc.), as well as from any deformation - The CHx channel address selected with the 4 path DIP SWITCH in the
which might occur during use. receiver, must correspond to the one set in the transmitter by means of
¥ The installation must comply with the provisions set out by the following the points to be welded (fig.3-4).
European Directives:It complies with the 89/336/EEC, 1999/5/CEE, - The transmitter TEO1 normally transmits on the CH1 channel with the
European Directive and subsequent amendments. possibility of setting a different address by welding the jumpers present
348 ¥ Disconnect the electrical power supply before carrying out any work on on the printed circuit (fig.3).
the installation. Also disconnect any buffer batteries, if fitted. - The transmitter TEO2 normally transmits: button 1-CH1, button 2-CH2,
¥ Fit an omnipolar or magnetothermal switch on the mains power supply, with the possibility of setting a different address by welding the jumpers
having a contact opening distance equal to or greater than 3mm. present on the printed circuit (fig.4).
¥ Check that a differential switch with a 0.03A threshold is fitted just - The transmitter TEO4 normally transmits: button 1-CH1, button 2-CH2,
before the power supply mains. button 3-CH3, button 4-CH4 without the possibility of setting a different
¥ Check that earthing is carried out correctly: connect all metal parts for address (fig.5).
closure (doors, gates etc.) and all system components provided with an
earth terminal. NOTE: The drawings in this manual are purely indicative. The arrangement
¥ Fit all the safety devices (photocells, electric edges etc.) which are of the DIP SWITCH and the POINTS TO BE WELDED may vary. The
needed to protect the area from any danger caused by squashing, procedure described, however, for the SETTING OF THE CODING and
conveying and shearing. BUTTON - TRANSMISSION CHANNEL ADDRESS remains the same.
¥ Position at least one luminous signal indication device (blinker) where
it can be easily seen, and fix a Warning sign to the structure. 7) MAINTENANCE AND DEMOLITION
¥ The Company declines all responsibility with respect to the automation The maintenance of the system should only be carried out by qualified
safety and correct operation when other manufacturers components personnel regularly. The materials making up the set and its packing must
are used. be disposed of according to the regulations in force.
¥ Only use original parts for any maintenance or repair operation. Batteries must be properly disposed of.
¥ Do not modify the automation components, unless explicitly authorised
by the company. WARNINGS
¥ Instruct the product user about the control systems provided and the Correct controller operation is only ensured when the data contained
manual opening operation in case of emergency. in the present manual are observed. The company is not to be held
¥ Do not allow persons or children to remain in the automation operation responsible for any damage resulting from failure to observe the
area. installation standards and the instructions contained in the present
¥ Keep radio control or other control devices out of children s reach, in manual.
order to avoid unintentional automation activation.
¥ The user must avoid any attempt to carry out work or repair on the The descriptions and illustrations contained in the present manual
automation system, and always request the assistance of qualified are not binding. The Company reserves the right to make any alterations
personnel. deemed appropriate for the technical, manufacturing and commercial
¥ Anything which is not expressly provided for in the present instructions, improvement of the product, while leaving the essential product
is not allowed. features unchanged, at any time and without undertaking to update
the present publication.
2) TECHNICAL FEATURES OF THE TRANSMITTER
-Transmission frequency :433.92Mhz
-Button :Yellow color
-Power supply with battery :Alkaline 12V
-Capacity :50 ÷ 100 metres
D811166_04

-Working temperature :-10 +55 °C

-Coding by :10 DIP-SWITCH
-Number of combinations :1024 each channel

RADIO CONTROLS
 TEO 1-2-4 / REO/REO F 1-2 433.92 Mhz
FIG. 1 FIG. 4
44 18.5
PIAZZOLE A SALDARE
35 12.5 POINTS TO WELDER
POINTS A SOUDER
CH1 CH2 CH3 CH4
TEO4 STELLEN ZU ACHWEKSEN T1
PUNTOS A SOLDAR T1
1
1 TEO1 34 34 34 34
1 2 3 4 5 6 7 8 9 10 1 2 3 4
T2
TEO2 2 1
12 12 12 12 34
12
ON S ON 56
2 T2 78
3
65

82
1 2 3 4
56 56 56 56
4 3 ON 78 78 78 78 - +
S
ON
- +
1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 10 8 CODICE PERSONALE ALKALINE BATTERY

16 SETTING OF CODING
12V
CODIFICATION
EINGABE DER CODIERUNG
FIJACION CODIFICACION

FIG. 2
FIG. 5
10 8 7 6 5 4 3 2 1 T1
TEO4
IMPOSTAZIONE CODIFICA T2
SETTING OF CODING
ON CODIFICATION
S
2
1 2 3 4
EINGABE DER CODIERUNG
- +
T1 CH1
FIJACION CODIFICACION
ON ON ON
S
- +
1
1 2 3 4 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 T2 CH2
ALKALINE BATTERY
12V
T3 CH3

T4 CH4
FIG. 3
PIAZZOLE A SALDARE
POINTS TO WELDER
POINTS A SOUDER
STELLEN ZU ACHWEKSEN
PUNTOS A SOLDAR
CH1 CH2 CH3 CH4
34
T1 12
56
78
10 8 7 6 5 4 3 2 1 34 34 34 34
12 12 12 12

349
- +
ON
CODICE PERSONALE - +
1 2 3 4 5 6 7 8 9 10
SETTING OF CODING
CODIFICATION ALKALINE BATTERY
ON ON
S 12V
1 EINGABE DER CODIERUNG
1 2 3 4 1 2 3 4 5 6 7 8 9 10
D811166_04

RADIO CONTROLS