JOB CARD PACKAGE TITLE: SVI - A318/A319/A320/

12-22-32-640-001-A A321
Tail Number - MSN -
FSN
SU-SKB - 02204 - 001

Reference Title DocType

12-22-32-640-001-A Lubrication of Main Landing Gear and Doors AMM

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 1

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

** ON A/C FSN ALL

TASK 12-22-32-640-001-A
Lubrication of Main Landing Gear and Doors

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN

POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY

THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR
LOCAL REGULATIONS.

1. Reason for the Job

Refer to the MPD TASK: 321000-01
LUBRICATION OF MAIN LANDING GEAR AND DOORS

2. Job Set-up Information

A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTY DESIGNATION

No specific 1 ACCESS PLATFORM 3M (10 FT)-
ADJUSTABLE
No specific 1 LUBRICATING EQUIPMENT
No specific AR SAFETY BARRIER(S)
No specific AR SAFETY CLIP - CIRCUIT BREAKER
No specific 1 WARNING NOTICE(S)

B. Consumable Materials

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

REFERENCE DESIGNATION
02ABA1 Phosphate Ester Hydraulic Fluid-General
Power - -
03GBB1 Synthetic Oil base Grease-General Purpose
Clay Thickened -
03GBC1 Synthetic Oil base Grease-General Purpose
Lithium Thickened Low Temp. -
03GBD1 Synthetic Oil base Grease-General Purpose
Lithium Thickened -
03HBD9 Synthetic Ester base Grease-General
Purpose Low Temp -
08BAA9 Non Aqueous Cleaner-General - -
08BBB1 Non Aqueous Cleaner-- Petroleum Based -
14SBA1 Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS ZONE DESCRIPTION

731 L.H MAIN GEAR
734 MAIN DOOR
741 R.H MAIN GEAR
744 MAIN DOOR

D. Referenced Information

REFERENCE DESIGNATION
Ref. Installation of the Safety Devices on the
32-00-00-481-001-A Landing Gears
Ref. Installation of the Safety Devices on the
32-00-00-481-002-A Landing Gear Doors

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

REFERENCE DESIGNATION
Ref. Open the Main Gear Doors for Access
32-12-00-010-001-A
Ref. Close the Main Gear Doors after Access
32-12-00-410-001-A
Ref. Removal of the MLG Door Actuating-Cylinder
32-31-35-000-001-A
Ref. Installation of the MLG Door Actuating-
32-31-35-400-001-A Cylinder
Ref. Deactivation of the Air Data Probes
34-11-00-040-802-A
Ref. Reactivation of the Air Data Probes
34-11-00-440-801-A
Ref. 12-22-00-00 LUBRICATION - DESCRIPTION AND
OPERATION
Ref. Fig. MLG - Lubrication Points
Ref. Fig. MLG Door and Uplocks - Lubrication Points

3. Job Set-up

SUBTASK 12-22-32-941-050-A
A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS,
specified by the operator's instructions and your local
regulations.
(2) Make sure that the ground safety locks are installed on the
landing gear Ref. AMM TASK 32-00-00-481-001.
(3) On the panel 400VU:
- make sure that the landing-gear control-lever (6GA) is
in the DOWN position
- put a WARNING NOTICE(S) in position to tell persons
not to operate the landing gear.

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

(4) Put a WARNING NOTICE(S) in position to tell persons not to

operate the landing gear doors.

SUBTASK 12-22-32-010-050-A
B. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in
position adjacent to the applicable MLG.
(2) Open the applicable MLG door Ref. AMM TASK
32-12-00-010-001.
(3) Make sure that the safety device is installed on the applicable
MLG door actuating-cylinder Ref. AMM TASK
32-00-00-481-002.

SUBTASK 12-22-32-040-051-A
C. Deactivation of the Air Data Probes

WARNING: BEFORE YOU OPEN LGCIU1(2) CIRCUIT

BREAKERS 1GA, 52GA AND 58GA (2GA AND
59GA), OPEN ALL THE PROBE HEATER CIRCUIT-
BREAKERS.
IF YOU DO NOT OBEY THIS SEQUENCE:
- THE PROBES WILL BECOME TOO HOT.
- THIS CAN CAUSE DAMAGE TO EQUIPMENT AND
INJURY TO MAINTENANCE PERSONNEL.
(1) Do the deactivation of the air data probes for maintenance
Ref. AMM TASK 34-11-00-040-802.

SUBTASK 12-22-32-865-050-A
D. Open, safety and tag the circuit breaker(s) that follow(s). Use the
SAFETY CLIP(S) as necessary.

PANEL DESIGNATION FIN LOCATION

FLIGHT CONTROLS/
49VU FLP/CTL AND MONG/ 6CV B07
SYS1

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

PANEL DESIGNATION FIN LOCATION

FLIGHT CONTROLS/
49VU SLT/CTL AND MONG/ 5CV B06
SYS1
49VU L/G/LGCIU/SYS1/NORM 1GA C09
HYDRAULIC/BRAKING
121VU AND STEERING/SYS2/ 4GG M36
SPLY
HYDRAULIC/BRAKING
121VU AND STEERING/SYS2/ 3GG M35
CTL
HYDRAULIC/BRAKING
121VU AND STEERING/SYS1/ 1GG M34
CTL
HYDRAULIC/BRAKING
121VU AND STEERING/SYS1/ 2GG M33
IND AND/SPLY
HYDRAULIC/Y HYD/
121VU 3700GD Q37
PUMP ENG2/MONG
HYDRAULIC/Y HYD/
121VU 3701GD Q36
PUMP ENG2/CTL
HYDRAULIC/LGCIU/
121VU 2GA Q35
SYS2
HYDRAULIC/LGCIU/
121VU 52GA Q34
SYS1/GRND SPLY
FLIGHT CONTROLS/
121VU FLP/CTL AND/MONG/ 8CV Q21
SYS2
HYDRAULIC/G HYD/
121VU 1701GK R35
PUMP ENG1/CTL
HYDRAULIC/G HYD/
121VU 1702GK R34
PUMP ENG1/MONG
** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

PANEL DESIGNATION FIN LOCATION

EMB SB 32-1346 for A/C 001-002

121VU LGCIU/BAT SPLY/SYS2 59GA R33
121VU LGCIU/BAT SPLY/SYS1 58GA R32
** ON A/C FSN ALL
FLIGHT CONTROLS/
121VU 7CV R21
SLT/CTL/SYS2

SUBTASK 12-22-32-640-055-A
E. Preparation of the Equipment
(1) Make sure that the LUBRICATING EQUIPMENT is in the
correct condition before you fill it.
(2) Operate the LUBRICATING EQUIPMENT to make sure that the
lines and adaptor are full of new lubricant.
(3) Clean the greasers with a clean Textile-Lint free Cotton -
(Material Ref. 14SBA1) made moist with the Non Aqueous
Cleaner-General - - (Material Ref. 08BAA9).

4. Procedure
Ref. Fig. MLG - Lubrication Points
Ref. Fig. MLG Door and Uplocks - Lubrication Points

SUBTASK 12-22-32-640-051-J

CAUTION: DO NOT OPERATE POWER-OPERATED LUBRICATION

EQUIPMENT AT MORE THAN 207 bars (3000 psi). HIGH
LUBRICATION PRESSURE CAN CAUSE DAMAGE TO THE
AIRCRAFT.

CAUTION: FOR LUBRICATION OF THE GLAND HOUSING ON THE

LANDING GEAR BOTTOM-BEARING, USE ONLY HAND-
OPERATED LUBRICATION EQUIPMENT. POWER-
OPERATED LUBRICATION EQUIPMENT CAN CAUSE

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 6 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

EXTRUSION OF THE LANDING-GEAR BOTTOM-BEARING

SCRAPER-SEAL.
A. Lubrication of the MLG and Doors

NOTE: For lubricant grease specification and lubrication

requirements, Ref. AMM D/O 12-22-00-00.
(1) Use the figures together with the tables that follow, to find the
greasers.
(2) Lubricate the greasers of the MLG as follows:

(a) Lubricate greasers Item 1 in the MLG Table with the

Synthetic Oil base Grease-General Purpose Clay
Thickened - (Material Ref. 03GBB1) or the Synthetic Oil
base Grease-General Purpose Lithium Thickened Low
Temp. - (Material Ref. 03GBC1). Do this until new
grease comes out.

(b) Lubricate greasers Item 4 in the MLG Table with the

Synthetic Oil base Grease-General Purpose Clay
Thickened - (Material Ref. 03GBB1) or the Synthetic Oil
base Grease-General Purpose Lithium Thickened Low
Temp. - (Material Ref. 03GBC1) or the Synthetic Oil
base Grease-General Purpose Lithium Thickened -
(Material Ref. 03GBD1). Do this until new grease
comes out.

(c) Lubricate the remaining greasers in the MLG Table with

the Synthetic Ester base Grease-General Purpose Low
Temp - (Material Ref. 03HBD9), the Synthetic Oil base
Grease-General Purpose Clay Thickened - (Material
Ref. 03GBB1) or the Synthetic Oil base Grease-
General Purpose Lithium Thickened Low Temp. -
(Material Ref. 03GBC1). Do this until new grease
comes out.

(d) Lubricate greasers Items 2 thru 4 in the MLG DOOR

AND UPLOCKS Table with the Synthetic Ester base
Grease-General Purpose Low Temp - (Material Ref.
03HBD9), the Synthetic Oil base Grease-General
Purpose Clay Thickened - (Material Ref. 03GBB1) or

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 7 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

the Synthetic Oil base Grease-General Purpose Lithium

Thickened Low Temp. - (Material Ref. 03GBC1). Do this
until new grease comes out.

(e) Lubricate greasers Items 1 and 5 in the MLG DOOR

AND UPLOCKS Table with the Synthetic Ester base
Grease-General Purpose Low Temp - (Material Ref.
03HBD9), the Synthetic Oil base Grease-General
Purpose Clay Thickened - (Material Ref. 03GBB1) or
the Synthetic Oil base Grease-General Purpose Lithium
Thickened Low Temp. - (Material Ref. 03GBC1) as
follows:
- Use the hand-operated lubrication equipment to
lubricate the uplock with a maximum of two full
strokes.

(f) MLG Table:

Component/
No. Total Position of Greasers
Location
1 Retraction 6 1 on the piston rod
Actuating 2 on the piston rod
Cylinder attachment-pin
3 on the structure
attachment pin
2 Upper Leg 9 1 on the forward pintle
housing
1 on the aft pintle
housing
3 on the aft pintle pin
4 on the aircraft structure
at the forward pintle
bearing (it is permitted to
lubricate only 2 greasers
when the MLG is
installed)
3 Gland Housing 3 3 on the bottom bearing

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 8 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

Component/
No. Total Position of Greasers
Location
4 Torque Link 8 3 on the top torque link
2 on the top torque-link
attachment-pin
3 on the bottom torque
link
5 Lower Leg 2 1 on each lug
Lugs
6 Leg Side-Stay 2 2 on the leg attachment
Attachment bracket
7 Side-Stay 15 5 at the top cardan joint
7 at the middle joint
3 at the bottom cardan
joint
8 Lockstay 13 2 at the side-stay
attachment
3 at the middle joint
1 on the lockstay
attachment lug of the
upper leg
3 on the lockstay cardan
joint
2 on the top of the
lockstay
2 at the actuator
attachment
9 Lockstay 2 1 at each end of the
Actuating actuating cylinder
Cylinder
10 Side-Stay 4 2 at each bush
Bracket, at A/
C structure

(g) MLG DOOR AND UPLOCKS Table:

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 9 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

Component/
No. Total Position of Greasers
Location
1 MLG Door 4 2 on each side
Uplock
2 MLG Door 1 1 on the aft hinge
3 MLG Door 1 1 on the roller
Uplock-Roller
4 MLG Door 2 1 at each end of the
Actuating- actuating cylinder
Cylinder
5 MLG Uplock 4 2 on each side

(3) If the MLG door actuator-bearing housing shows signs of

lateral movement, do the steps that follow:

NOTE: The MLG door actuator-bearing housing can show

signs of circular movement, which is permitted.

(a) Remove the MLG door actuating-cylinder Ref. AMM

TASK 32-31-35-000-001.

(b) Send the MLG door actuating-cylinder to the workshop

for replacement of the MLG door actuator-bearing
housing.

(c) Install the serviceable MLG door actuating-cylinder Ref.

AMM TASK 32-31-35-400-001.

(4) Remove the unwanted grease as follows:

(a) Clean the greasers with a clean Textile-Lint free Cotton

- (Material Ref. 14SBA1) made moist with the Non
Aqueous Cleaner-General - - (Material Ref. 08BAA9).

(b) Make sure that the greaser ball is in the correct

position.

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 10 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

(5) Do an inspection of the chrome surfaces of the actuator piston

rods.

(a) Make sure that there is no grease on the chrome

surfaces of the actuator piston rods.

1 If you find grease on the chrome surfaces of the

actuator piston rods, do the steps that follow:

a Clean the chrome surfaces with a clean

Textile-Lint free Cotton - (Material Ref.
14SBA1) made moist with the Non
Aqueous Cleaner-- Petroleum Based -
(Material Ref. 08BBB1).

b Apply a thin layer of the Phosphate

Ester Hydraulic Fluid-General Power - -
(Material Ref. 02ABA1) with a clean
Textile-Lint free Cotton - (Material Ref.
14SBA1) on the chrome surfaces of the
actuator piston rods.

5. Close-up

SUBTASK 12-22-32-865-051-A
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s):

PANEL DESIGNATION FIN LOCATION

FLIGHT CONTROLS/
49VU FLP/CTL AND MONG/ 6CV B07
SYS1
FLIGHT CONTROLS/
49VU SLT/CTL AND MONG/ 5CV B06
SYS1
49VU L/G/LGCIU/SYS1/NORM 1GA C09

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 11 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

PANEL DESIGNATION FIN LOCATION

HYDRAULIC/BRAKING
121VU AND STEERING/SYS2/ 4GG M36
SPLY
HYDRAULIC/BRAKING
121VU AND STEERING/SYS2/ 3GG M35
CTL
HYDRAULIC/BRAKING
121VU AND STEERING/SYS1/ 1GG M34
CTL
HYDRAULIC/BRAKING
121VU AND STEERING/SYS1/ 2GG M33
IND AND/SPLY
HYDRAULIC/Y HYD/
121VU 3700GD Q37
PUMP ENG2/MONG
HYDRAULIC/Y HYD/
121VU 3701GD Q36
PUMP ENG2/CTL
HYDRAULIC/LGCIU/
121VU 2GA Q35
SYS2
HYDRAULIC/LGCIU/
121VU 52GA Q34
SYS1/GRND SPLY
FLIGHT CONTROLS/
121VU FLP/CTL AND/MONG/ 8CV Q21
SYS2
HYDRAULIC/G HYD/
121VU 1701GK R35
PUMP ENG1/CTL
HYDRAULIC/G HYD/
121VU 1702GK R34
PUMP ENG1/MONG
** ON A/C FSN ALL

EMB SB 32-1346 for A/C 001-002

121VU LGCIU/BAT SPLY/SYS2 59GA R33
121VU LGCIU/BAT SPLY/SYS1 58GA R32

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 12 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

PANEL DESIGNATION FIN LOCATION

** ON A/C FSN ALL
FLIGHT CONTROLS/
121VU 7CV R21
SLT/CTL/SYS2

SUBTASK 12-22-32-440-051-A
B. Reactivation of the Air Data Probes

WARNING: BEFORE YOU CLOSE PROBE HEATER CIRCUIT-

BREAKERS 1DA1(2), 3DA1(2,3), 4DA1(2,3) AND
5DA1(2,3), CLOSE THE LGCIU, EIU AND PHC
CIRCUIT BREAKERS.
IF YOU DO NOT OBEY THIS SEQUENCE:
- THE PROBES WILL BECOME TOO HOT.
- THIS CAN CAUSE DAMAGE TO EQUIPMENT AND
INJURY TO MAINTENANCE PERSONNEL.
(1) Do the reactivation of the air data probes after maintenance
Ref. AMM TASK 34-11-00-440-801.

SUBTASK 12-22-32-410-050-A
C. Close Access
(1) Make sure that the work area is clean and clear of tools and
other items.
(2) Remove the access platform(s).
(3) Close the applicable MLG door Ref. AMM TASK
32-12-00-410-001.

SUBTASK 12-22-32-942-050-A
D. Removal of Equipment
(1) Remove the SAFETY BARRIER(S).
(2) Remove the WARNING NOTICE(S).
(3) Remove the ground support and maintenance equipment, the
special and standard tools and all other items.

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 13 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

B
F

Q G
N

P
L
K

M
J

Figure 12-22-32-991-00100-00-H (SHEET 1/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 14 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

E C

D
B

C D E

Figure 12-22-32-991-00100-00-H (SHEET 2/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 15 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

Figure 12-22-32-991-00100-00-H (SHEET 3/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 16 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

Figure 12-22-32-991-00100-00-H (SHEET 4/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 17 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

Figure 12-22-32-991-00100-00-H (SHEET 5/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 18 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

8
K

Figure 12-22-32-991-00100-00-H (SHEET 6/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 19 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

M
9

Figure 12-22-32-991-00100-00-H (SHEET 7/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 20 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

Figure 12-22-32-991-00100-00-H (SHEET 8/8) - MLG - Lubrication Points

** ON A/C FSN ALL

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 21 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2022
AMM - SVI - A318/A319/A320/A321 TASK:
12-22-32-640-001-A
Tail Number - MSN - TITLE: 12-22-32-03 CONF 00
FSN: 12-22-32-640-001-A - Lubrication of Main Landing Gear and
SU-SKB - 02204 - 001 Doors

MECH. INSP.

1
B

1
B
C 4

5
3

Figure 12-22-32-991-00200-00-D (SHEET 1) - MLG Door and Uplocks - Lubrication

Points
** ON A/C FSN ALL
© *** END OF CARD ***

JCP Title: 12-22-32-640-001-A CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 22 of 22

PRINT DATE: Dec 10/2022
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE