ECU list

ComAp Electronic Engines

Support

SW version 8.1.1
1 General information 3
2 Changes in version 8.1.1 4
3 Changes in version 8.1.0 5
4 Changes in version 8.0.0 8
5 Changes in version 7.9.0 10
6 Changes in version 7.8.1 14
7 Changes in version 7.8.0 15
8 Changes in version 7.7.0 17
9 Changes in version 7.6.0 19
10 Changes in version 7.5.0 21
11 Changes in version 7.4.0 24
12 Changes in version 7.3.1 27

Copyright © 2023 ComAp a.s.

Written by Jakub Vávra
Prague, Czech Republic
ComAp a.s., U Uranie 1612/14a,
170 00 Prague 7, Czech Republic
Tel: +420 246 012 111
E-mail: info@comap-control.com, www.comap-control.com New Features List
 29 Notes 67

ECU list 8.1.1 New Features List 2

1 General information
1.1 Version information
ECU List version 8.1.1 is dedicated for every ComAp controller with standard firmware and support an
electronic engine.

1.2 Clarification of Notation

Note: This type of paragraph calls the reader’s attention to a notice or related theme.

IMPORTANT: This type of paragraph highlights a procedure, adjustment etc., which can cause a
damage or improper function of the equipment if not performed correctly and may not be clear at
first sight.

This type of paragraph highlights a procedure, adjustment etc., which can cause a damage or improper
function of the equipment if not performed correctly and may not be clear at first sight.
Example: This type of paragraph contains information that is used to illustrate how a specific function
works.

ECU list 8.1.1 New Features List 3

2 Changes in version 8.1.1
IMPORTANT: Please start using ECU List – Standard.esl, other ESLs will be removed in ECU list
version 8.2.0.

IMPORTANT: ECU list - InteliNano.esl has been removed. All future changes will be released with
the NanoEdit install suite.

2.1 Bug Repairs

ECU list - Standard
Fixed issue where ECUs were shown for IG1000 when they should not have been visible.

ECU list 8.1.1 New Features List 4

3 Changes in version 8.1.0
IMPORTANT: Please start using ECU List – Standard.esl, other ESLs will be removed in ECU list
version 8.2.0.

IMPORTANT: ECU list - InteliNano.esl has been removed. All future changes will be released with
the NanoEdit install suite.

3.1 New Features

New ECUs being supported
ABB/Firmer PCS-100
ABB PVI10.0
ABB PVS 100
ABB Trio
Delta PCS100HV
Delta M series
Growatt PV Inverter
Huawei SUN2000
Huawei Smart Logger
Leroy Somer AVR D500 control
Schneider Conext CL60E, CL60A
Sinexcel PW2 / PWS1
SMA Sunny Island
SMA Sunny Tripower / Sunny Boy
SMA Solid Q
Sungrow string inverters
Sunspec BESS
Sunspec PV
Tesla Megapack
THQ Tronic LSU49
Woodward ProAct ISC
ECU List Standard.esl
Support for new visualisation with groups and subgroups has been added. This only works with
InteliConfig version 2.35. and higher.
Cummins PGI
Parameter SPN 5565 "Coolant Level Engine Protection Shutdown Override Command" is now
configured by default with logical 1 as a source.
Iveco MD1
Parameters "Forced Thermal Treatment Counter Reset" has been added.
Suport for IG500 controllers family has been added.

ECU list 8.1.1 New Features List 5

 Jichai EU3A
Parameters "Number of PCD Activations", "Accounted PCD Time", "PCD Inducement Severity" and
"PCD Inducement Reason" has been added.
Powerlink
Suport for IG500 controllers family has been added.
Suport for IG200 controllers family has been added.
Leroy Somer CD500
Suport for IG500 controllers family has been added.
Suport for IG200 controllers family has been added.
MTU MIP4000 CAN
Many new faultcodes has been added regarding "SD T-Exhaust".
Parameter "T-Mixture A" has changed to "T-Mixture B"
Parameters "Control - Testing Plant Active", "Deactivate frequency regulation in island operation" and
"Frequency Regulation In Island Operation Deactivated From External" has been added.
Scania S6 Allspeed
Suport for IG500 controllers family has been added.
Scania S8 Allspeed
Many new faultcode texts has been added.
Suport for IG500 controllers family has been added.
Scania S8 Singlespeed
Many new faultcode texts has been added.
Volvo Industrial EMS 2.4
Suport for IG500 controllers family has been added.
Weichai Wise18B
Parameter SPN 513 "Actual Engine - Percent Torque" has been added.
Weichai Wise18B Duel
Parameter SPN 513 "Actual Engine - Percent Torque" has been added.
Changed dimensions from hPa to Bar.

3.2 Bug Repairs

Baudouin LECM E6
Issue with mixed up controller and ECU addresses has been fixed.
Jenbacher Diane
Allmost all parameters has been fixed and updated according to newest Jenbacher documentation.
Kohler KDI

Parameter SPN1761 "Aftertreatment 1 Diesel Exhaust Fluid Tank 1 Level" has been fixed from analog
input to analog output.
Waukesha ESM2
Issues where parameters displayed incorrect values has been fixed.

ECU list 8.1.1 New Features List 6

 Weichai Wise18B
Parameters "Air Filter Pressure (Master)" , "Air Filter Pressure (Slave)", "Fuel Oil Pressure Outlet",
"Fuel Oil Pressure Inlet", "Fuel Oil Pressure Before Coarse Filter (Master)", "Fuel Oil Pressure Before
Coarse Filter (Slave)", "Fuel Oil Pressure After Coarse Filter (Master)", "Fuel Oil Pressure After Coarse
Filter (Slave)", "Rail Pressure (Master)" and "Rail Pressure (Slave)" has been moved from binary
inputs to analog inputs.

3.3 Removed Features

Fronius Symo
Module Fronius Symo has been removed. The support for it will continue in new added Sunspec PV
module.
ECU list - InteliNano
ECU list - InteliNano.esl has been removed. The support for it will continue in new ECU list -
InteliNano released together with NanoEdit install suit.

ECU list 8.1.1 New Features List 7

4 Changes in version 8.0.0
IMPORTANT: Please start using ECU List – Standard.esl, other ESLs will be removed in ECU list
version 8.2.0.

Note: We moved ECUs from ECU list – GEMS-Multiecu.esl to ECU list – Standard.esl.
ECU list – GEMS-multiecu.esl will cease to exist in future versions of ECU list – GEMS.

4.1 New Features

New ECUs being supported
Altronic CD200
Altronic NGI 1000RC
Continental Uninox
E-Controls EICS
Gas Engine Technology GMF
Heinzmann Ariande
Henzmann Helenos
Heinzmann Kronos
Heinzmann Pandaros
Heinzmann Phlox
HuegliTech SG500 & SG100
Jichai EU3A
HuegliTech LEF200
Motortech MIC850
Motortech Varistep 1
Motortech Varistep 2
MWM ADEM 4
Powerlink
TPEM
Triject GAS
Weichai Wise18B Duel
Woodward IC920
Caterpillar J1939
Parameter SPN 515 "Engine’s Desired Operating Speed" has been added.
MAN EDC17
Parameters "Status of Urea Tank Level", "Status of Urea Quality" and "Status of Monitoring System"
has been added. These values are connected to aftertreatment lamps by default.
Counter and Checksum parameters has been added to TSC1 messages.
Volvo Industrial EMS 2.4
Parameters "Number of PCD Activations", "Accounted PCD Time", "PCD Inducement Severity" and
"PCD Inducement Reason" has been added.

ECU list 8.1.1 New Features List 8

 Weichai Wise18B
Parameter "Exhaust Temperature 2" has been added.

4.2 Bug Repairs

Cummins CM870
Issue where warning poped up after configuration in ID-DCU has been fixed.
Cummins PGI 1.1
Issue where parameter Fuel Rate might not work correctly has been fixed.
For parameter SPN 5526 "Coolant Level Engine Protection Shutdown Override Command" is now
possible to configure the source of value.
Iveco NEF & Cursor
Issue with controlling speed on new engines has been fixed.
Iveco MD1
Issue where inhibit lamp did not behave correctly has been fixed.
Iveco MD1 IPU
Issue where inhibit lamp did not behave correctly has been fixed.
MTU ECU7 Direct
High limit for parameter "CANSpdSwitch" has been changed to 32767.
MTU MIP4000
Issue where some parameters requiring a request did not work has been fixed.
Perkins ECM
Issue where speed request was not sent correctly has been fixed.
Scania S8 Allspeed
Issue where diagnostic messages from aftertreatment unit werent read corrrectly has been fixed.
Scania S8 Allspeed
Issue where diagnostic messages from aftertreatment unit werent read corrrectly has been fixed

4.3 Removed Features

Leroy Somer CD500
All output values have been removed

ECU list 8.1.1 New Features List 9

5 Changes in version 7.9.0
5.1 New Features
New ESL ECU list – Standard
New ESL containing information about all engines in the ECU list.

IMPORTANT: Please start using this ESL, other ESLs will be removed in ECU list version 8.2.0

New ECUs being supported

Baudouin LECM E6
Baudouin SECM70
Fronius Symo
Kubota EDC17
ModbusUserDevice
MWM SECM70
Siements GCS-E
Waukesha ESM2
AGCO Power EEM4
Parameter DEF Tank Level now visible in ECU Values.
Caterpillar J1939
Parameter DEF Tank Level now visible in ECU Values.
Parameters SPN 8148 Aftertreatment System Enable Command, SPN 9175 Aftertreatment SCR
Dosing Mode Command, SPN 7851 Aftertreatment System Enable Status and SPN 9176
Aftertreatment SCR Dosing Mode Status have been added.
Caterpillar ADEM A6
Parameters SPN 7746 Engine Start Request, SPN 7747 Engine Start Consent, SPN 8148
Aftertreatment System Enable Command, SPN 9175 Aftertreatment SCR Dosing Mode Command,
SPN 7851 Aftertreatment System Enable Status and SPN 9176 Aftertreatment SCR Dosing Mode
Status have been added.
Cummins CM2350 Industrial
Parameter SPN 3695 Aftertreatment Regeneration Inhibit Switch has been added.
Deutz EMR4
Parameter SCR Warning Lamp / EAT Inducement lamp has been added.
Behavior of DEF Low Level Lamp has been linked to new parameter.
Deutz EMR5
Parameters SCR Warning Lamp / EAT Inducement lamp, Standstill Regeneration Stop, Standstill
Regeneration Release, Start EOL Routine, EOL Routine, Inhibit Heat Mode, EAT Override Switch
have been added.
Behavior of DEF Low Level Lamp has been linked to new parameter.
Isuzu ECM
Isuzu engines 4LE2TA and 4LE2TX are now being supported.

ECU list 8.1.1 New Features List 10

 John Deere JDEC
Parameter DPF Regeneration Control Request has been added.
Kubota ECM
Parameters SPN 29 Accelerator Pedal Position 2, SPN 52 Engine Intercooler Temperature, SPN 106
Engine Intake Air Pressure and SPN 158 Key Switch Battery Potencial have been added.
MTU Smart Connect
Parameter SPN 174 Engine Fuel Temperature 1 has been added.
Perkins ADEM A6E11
Parameters SPN 7746 Engine Start Request, SPN 7747 Engine Start Consent and SPN 518 Engine
Requested Torque/Torque Limit has been added.
Perkins ECM
Perkins series 1200 is now being supported.
Standard J1939 engine
Parameters SPN 7746 Engine Start Request and SPN 7747 Engine Start Consent have been added.
Yanmar EDC17
Parameters SPN 110 Engine Coolant Temperature and SPN 174 Engine Fuel 1 Temperature 1 have
been added.

5.2 Bug Repairs

Caterpillar ADEM A6
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Caterpillar J1939
Issue where parameters Elevated Engine Allowed Switch and Aftertreatment Regeneration Engine
Speed Allowed Switch weren’t sent properly has been fixed.
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Caterpillar ADEM & EMCP
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Cummins CM2150
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Cummins CM500
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Cummins CM850
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.

ECU list 8.1.1 New Features List 11

 Deutz EMR4
Issue where engine did not start was fixed.
Description in PC tools has been fixed.
Deutz EMR5
Issue where engine did not start was fixed.
Isuzu ECM
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Kubota ECM
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Liebherr LIDEC1
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
MTU DDEC10
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Perkins ECM
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Scania S8 Allspeed
Behavior of HEST lamp has been fixed
Scania S8 Singlespeed
Behavior of HEST lamp has been fixed
Standard J1939 engine
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Standard J1939 monitor
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.
Volvo Industial EMS 2.4
Fixed issue where error messages appeared during configuration in certain controllers.
Volvo Industrial
Fixed issue where error messages appeared during configuration in certain controllers.
Yanmar EDC17
Fixed issues with parameters Regeneration Interlock Switch, DPF Regeneration Prohibition Swtich
and DPF Regeneration Request Switch.
Behavior of DPF lamp has been fixed.
Yanmar TNV
Behavior of DPF lamp has been fixed.

ECU list 8.1.1 New Features List 12

 Yuchai YC-LH
Issue where parameter SPN 157 Engine Fuel 1 Injector Metering Rail 1 Pressure was not visible for
IGS-NT controllers has been fixed.

ECU list 8.1.1 New Features List 13

6 Changes in version 7.8.1
6.1 Bug Repairs
Issues where missing parameters caused various problems in many ECUs have been fixed.

ECU list 8.1.1 New Features List 14

7 Changes in version 7.8.0
7.1 New Features
New ECUs being supported
Sinotruk BBM
Iveco MD1
Added support for new CS 069 calibration, Iveco MD1 now requires multiple counter and checksum
support on the controller side.
Aftertreatment lamps updated according to latest Iveco documentation for Iveco F35, F36 engines.
Parameter SCR Catalyst Full has been added.
Parameter ACM Inhibited (SPN 3703) has been added.
Parameter EGR/DPF Inducement has been added.
Iveco MD1 IPU
Aftertreatment lamps updated according to latest Iveco documentation for Iveco F35, F36 engines.
Parameter SCR Catalyst Full has been added.
Parameter ACM Inhibited (SPN 3703) has been added.
Parameter EGR/DPF Inducement has been added.
Isuzu ECM
Parameter Regeneration Inhibit has been added.
Parameter Override Control Mode (SPN 897) has been added.
Leroy Somer CD500
Parameter Requested Generator Overall Power Factor Lagging (SPN 3385) has been added.
MTU MIP4000 J1939
Parameters Speed Higher, Speed Lower, Voltage Higher, Voltage Lower are now configured by
default.
Kohler KDI
Parameter Aftertreatment 1 Diesel Exhaust Fluid Tank Level (SPN 1761) has been added
Scania S8 Allspeed
New Faultcode text for SPN 3362 has been added
Weichai Wise 18B
Parameter Exhaust Temperature has been added.
Yanmar TNV
Parameter Exhaust System High Temperature Lamp Command has been added.
Parameters Time Remaining at Present Inducement, Pending EGR Inducement Severity, Operator
Inducement Active for EGR System Fault, Exhaust Temperature Lamp Status, DPF Regeneration
Acknowledge Lamp Status, Buzzer, Starter Relay Status, Coolant Temperature Warning Lamp,
Amber Warning Lamp Status, Red Engine Stop Lamp Status has been added.
Rules for Aftertreatment lamps has been changed aproprietely.

ECU list 8.1.1 New Features List 15

 Yuchai YECU
Parameters P-Fuelpmplnt, P-FuelFltDiff, P-Crankcase, P-OilFilter, P-IntakeAir, T-ExhaustFront, T-
ExhaustRear has been added.

7.2 Removed Features

Weichai Wise 13A
Parameter Engine Shutdown Override switch SPN 1237 has been removed.

7.3 Bug Repairs

Adelsystem CB12245AJ
Connection problems with battery charger has been fixed.
Cummins CM2350
Problem with Speed Request message has been fixed.
Cummins CM570
Problem with Speed Request message has been fixed.
Cummins CM850
Problems where speed control did not work has been fixed.
Deutz EMR4
Transmitt period of frame 0xFF44 has been changed to 100ms.
Deutz EMR5
Transmitt period of frame 0xFF44 has been changed to 100ms.
Leroy Somer CD500
Parameters Requested Generator Average Line-Line AC RMS Voltage, Requested Generator Total
AC Reactive Power, Requested Generator Overall Power Factor, Voltage Regulator Var/Power Factor
Operating Mode, Voltage Regulator Underfrequency Compensation Enabled, Voltage Regulator
Enabled and Voltage Regulator Soft Start State has been fixed.
Isuzu ECM
Message with parameter for Stop Request has been fixed

ECU list 8.1.1 New Features List 16

8 Changes in version 7.7.0
8.1 New Features
New ECUs being supported
Adelsystems Battery Charger CB12245AJ (Allspeed.esl, InteliConfig.esl)
Cummins CM2350 Industrial (Allspeed.esl)
MTU MIP4000 J1939 (Gensets.esl, InteliConfig.esl)
AVR Marathon DVR2000EC (Allspeed.esl)
Caterpillar ADEM A6
Parameter SPN 7580 has been added
Deutz EMR4
Correct support of lamp SPN 3697 Diesel Particulate Filter Lamp Command has been added (Deutz is
using non-standard lamp behavior)
Deutz EMR5
Correct support of lamp SPN 3697 Diesel Particulate Filter Lamp Command has been added
Doosan
Support of lamp SPN 4175 Diesel Particulate Filter Active Regeneration Forced Status has been
added
Leroy Somer CD500
Parameter SPN 3378 Voltage Regulator Soft Start State has been added
Liebherr LIDEC2
Parameter SPN 2452 Generator Total Real Power has been added
Parameter Power Setpoint Demand has been added
Scania S8
Parameters SPN 4331 Aftertreatment 1 Diesel Exhaust Fluid Actual Dosing Quantity, SPN 4360
Aftertreatment 1 SCR Catalyst Intake Gas Temperature, SPN 4361 Aftertreatment 1 SCR Catalyst
Intake Gas Temperature Preliminary FMI, SPN 4362 Aftertreatment 1 SCR Catalyst Outlet Gas
Temperature Preliminary FMI SPN 4363 Aftertreatment 1 SCR Catalyst Outlet Gas Temperature, SPN
1761 Aftertreatment 1 Diesel Exhaust Fluid Tank Level, SPN 3031 Aftertreatment 1 Diesel Exhaust
Fluid Tank Temperature, SPN 3517 Aftertreatment 1 Diesel Exhaust Fluid Tank Level 2, SPN 3532
Aftertreatment 1 Diesel Exhaust Fluid Tank Level Preliminary FMI has been added
Volvo Industrial EMS 2.4
Parameters ACM System power down ack, SPN 1761 Aftertreatment 1 Diesel Exhaust Fluid Tank
Level, SPN 3031 Aftertreatment 1 Diesel Exhaust Fluid Tank Temperature, SPN 5245 Aftertreatment
Diesel Exhaust Fluid Tank Low Level Indicator has been added
Weichai Wise10B
Parameter SPN 92 Engine Percent Load At Current Speed, SPN 695 Engine Override Control Mode
has been added
Weichai Wise18B
Parameter SPN 92 Engine Percent Load At Current Speed, SPN 695 Engine Override Control Mode
has been added

ECU list 8.1.1 New Features List 17

8.2 Removed features
Waukesha EMS2 support has been removed temporarily.

8.3 Bug Repairs

MAN EDC17
All request frames are sent with destination address 0xFF instead of 0x00. This should fix problems
with certain parameters not being displayed.
Weichai Wise10B
Parameters Right Lube Oil Temperature and Right Lube Oil Pressure has been fixed

ECU list 8.1.1 New Features List 18

9 Changes in version 7.6.0
9.1 New Features
New ECUs being supported
Dongfeng Cummins
Iveco MD1 IPU (allspeed.esl only)
Liebherr LIDEC2
MTU MIP4000 J1939
Yanmar EDC17
PSI E-control
Allspeed.esl
Iveco MD1 has been added
InteliLite.esf
Weichai Wise 12B has been added
Weichai Wise 13A has been added
Weichai Wise 15A has been added
InteliNano.esf
Weichai Wise 12B has been added
Weichai Wise 13A has been added
Weichai Wise 15A has been added
Cummins CM2350
Parameter SPN 441 Auxiliary Temperature 1 has been added
Parameter SPN 442 Auxiliary Temperature 2 has been added
Parameter SPN 1387 Auxiliary Pressure 1 has been added
Parameter SPN 1388 Auxiliary Pressure 2 has been added
Deutz EMR4
Parameter Stationary/Neutral switch has been added
Deutz EMR5
Parameter Stationary/Neutral switch has been added
Doosan MD1
Time and date messages has been switched to outputs
MTU MIP4000
16 Warning parameters and 16 Shutdown parameters has been added
Scania S8 Allspeed
Parameter SCR Operator Inducement Override Enable has been added
Parameter SCR Operator Inducement Override Time Remaining has been added
Parameter Number of SCR Operator Inducement Override Events Remaining has been added
Parameter Total Number of SCR Operator Inducement Override Events has been added
Parameter SCR Operator Inducement Override Switch has been added

ECU list 8.1.1 New Features List 19

 Scania S8 Singlespeed
Parameter SCR Operator Inducement Override Enable has been added
Parameter SCR Operator Inducement Override Time Remaining has been added
Parameter Number of SCR Operator Inducement Override Events Remaining has been added
Parameter Total Number of SCR Operator Inducement Override Events has been added
Parameter SCR Operator Inducement Override Switch has been added
Standard J1939 engine, Standard J1939 monitor
Parametr SPN 191 Transmission Output Shaft Speed has been added
Parametr SPN 161 Transmission Input Shaft Speed has been added
Parametr SPN 523 Transmission Current Gear has been added
Parametr SPN 2900 Transmission Engine Crank Enable has been added
Parametr SPN 1851 Transmission Shift Inhibit Indicator has been added
Parametr SPN 2539 Transmission Mode 4 Indicator has been added
Parametr SPN 2538 Transmission Mode 3 Indicator has been added
Parametr SPN 2537 Transmission Mode 2 Indicator has been added
Parametr SPN 2536 Transmission Mode 1 Indicator has been added
Parametr SPN 3289 Transmission Requested Gear Feedback
Parametr SPN 4252 Transmission Mode 7 Indicator has been added
Parametr SPN 4253 Transmission Mode 8 Indicator has been added
Parametr SPN 127 Transmission Oil Pressure has been added
Parametr SPN 177 Transmission Oil Temperature 1 has been added
Parametr SPN 167 Charging System Potential (Voltage) has been added
Parametr SPN 444 Battery Potential / Power Input 2 has been added

9.2 Removed features

Support of KWP2000 protocol has been removed, this involves ECUs Volvo and Scania. J1939 protocols
DM1 messages will be used instead.

9.3 Bug Repairs

Doosan G2 EDC17
HEST Lamp SPN 3698 has been fixed
John Deere JDEC
Problems with speed control parameters has been fixed
Kohler KDI
Problems with speed control parameters has been fixed
CAN Bus address changed from 0x03 to 0x05
MTU DDEC10
Problems with speed control parameters has been fixed
Waukesha ESM2
Parameter engine hours has been fixed

ECU list 8.1.1 New Features List 20

10 Changes in version 7.5.0
10.1 New Features
Added support for controller family ID4
New ECUs being supported:
Deep Sea AVR DSEA109 (Allspeed.esl)
Daimler CPC4
Caterpillar ADEM & EMCP
New parameter EMCP Fuel Level has been added
Caterpillar J1939
Parameter SPN 696 Engine Requested Speed Control Conditions has been added
Parameter SPN 897 Override Control Mode Priority has been added
Parameter SPN 1122 Engine Alternator Bearing 1 Temperature has been added
Parameter SPN 1123 Engine Alternator Bearing 2 Temperature has been added
Parameter SPN 1124 Engine Alternator Winding 1 Temperature has been added
Parameter SPN 1125 Engine Alternator Winding 2 Temperature has been added
Parameter SPN 1126 Engine Alternator Winding 3 Temperature has been added
Cummins CM2880
Speed Request message frame update period has been changed from 20ms to 10ms
Hatz
Hatz has been renamed to Hatz EDC17
Iveco NEF&Cursor
Iveco NEF&Cursor is no longer available in NanoEdit
John Deere
John Deere has been renamed to John Deere JDEC
Kohler
Kohler has been renamed to Kohler KDI
Kubota
Kubota has been renamed to Kubota ECM
Liebheer
Liebheer has been renamed to Liebheer LIDEC1
Perkins ECM
Parameter SPN 3542 has been added
Support of Perkins 1200 series has been added
Scania S6 Allspeed from ver.1794335
Scania S6 Allspeed from ver.1794335 has been reanamed to Scania S6 Allspeed
Scania S6 Singlespeed from ver.1794335
Scania S6 Singlespeed from ver.1794335 has been reanamed to Scania S6 Singlespeed

ECU list 8.1.1 New Features List 21

 Scania S8 Allspeed
Parameters DPF Regeneration State, DPF Regeneration Countdown Timer and Urea Level
Inducement
State are now configured automatically for controllers supporting Stage V.
Parameter DPF Regeneration Countdown Timer has now dimension “min” as minutes
Scania S8 Singlespeed
Parameters DPF Regeneration State, DPF Regeneration Countdown Timer and Urea Level
Inducement
State are now configured automatically for controllers supporting Stage V.
Parameter DPF Regeneration Countdown Timer has now dimension “min” as minutes
Volvo Industrial
Parameter Sea Water pressure from frame VP72 has been added, this parameter is dedicated for
engines in marine application.
Volvo Industrial EMS 2.4
Parameter Sea Water pressure from frame VP72 has been added, this parameter is dedicated for
engines in marine application.
Yanmar TNV
Parameter Droop Mode Status is being configured automatically
Parameter SPN 695 Engine Override Control Mode has been added

10.2 Removed features

Cummins CM570
Cummins CM570 is no longer available in NanoEdit
Cummins CM850
Cummins CM850 is no longer available in NanoEdit
Cummins PGI
Cummins PGI is no longer available in NanoEdit
DeutzEMR4
Deutz EMR4 is no longer available in NanoEdit

Note: From ECU list 7.5.0 all support of KWP2000 protocol will be removed, this involves ECUs Volvo and
Scania. J1939 protocols DM1 messages will be used instead.

10.3 Bug Repairs

Cummins PGI
Issue where fault code 639 has been sent by Chinese version of ECU has been fixed
Deutz EMR5
Issue where ECU has not responded to controller speed request has been fixed
Doosan EDC17
Issue where ECU didn’t react to speed control has been fixed
Doosan MD1
Issue where ECU didn’t react to speed control has been fixed

ECU list 8.1.1 New Features List 22

 JCB DCM
Issue with not working aftertreatment lamp Aftertreatment Lamp Status, parameter Inducement Level
and parameter Refresh Status Byte has been fixed
Kohler KDI
Issues with engine instability during running has been fixed
Yanmar TNV
Parameter Regeneration Inhibit has been fixed

ECU list 8.1.1 New Features List 23

11 Changes in version 7.4.0
11.1 New Features
New ECUs being supported:
Perkins ADEM A6E11
Baudouin WISE10B
Doosan MD1
Volvo Industrial EMS2.4
This ECU configuration is solely for engines equipped with EMS2.4 ECU with counter and
checksum. No NT controllers support.
Caterpillar ADEM A6
Aftertreatment Interlock parameter is now supported for GSC controllers
Cummins CM850/CM2150/CM2250
Parameter SPN 970 Engine Auxiliary Shutdown Switch has been added
Hatz
Has been renamed to Hatz EDC17
Iveco MD1
Aftertreatment Interlock parameter is now supported for GSC controllers
JCB DCM
Stage V support has been added
Added new fault codes text (full list will be included in new version of Electronic Engines Support
guide)
Kohler
Parameter SPN 3698 Aftertreatment Regeneration Force Switch has been added
MTU ADEC J1939
Parameter SPN 250 Engine Total Fuel Used has been added
MTU ADEC J1939 P-engines
Parameter SPN 250 Engine Total Fuel Used has been added
MTU ECU7 Direct
Picture of ECU and connectors has been added
Scania S6 Allspeed from ver. 1794335
Parameter SPN 70 Parking Brake Switch has been added
Parameter SPN 523 Transmission Current Gear has been added
Scania S6 Singlespeed from ver. 1794335
Parameter SPN 70 Parking Brake Switch has been added
Parameter SPN 523 Transmission Current Gear has been added
Scania S8 Allspeed
Aftertreatment Interlock parameter is now supported for GSC controllers
Parameter SPN 70 Parking Brake Switch has been added

ECU list 8.1.1 New Features List 24

 Parameter SPN 523 Transmission Current Gear has been added
Parameter Fuel Level has been added
Parameter SPN 5629 DPF Active Regeneration Inhibit Status has been added
Parameter SPN 2432 Engine Demand – Percent Torque has been added
Scania S8 Singlespeed
Aftertreatment Interlock parameter is now supported for GSC controllers
Parameter SPN 70 Parking Brake Switch has been added
Parameter SPN 523 Transmission Current Gear has been added
Parameter Fuel Level has been added
Parameter SPN 5629 DPF Active Regeneration Inhibit Status has been added
Parameter SPN 2432 Engine Demand – Percent Torque has been added
Volvo Allspeed
Has been renamed to Volvo MarineProp
Volvo Singlespeed
Has been renamed to Volvo Industrial
Counter and Checksum parameter has been removed
Yanmar TNV
Aftertreatment Interlock parameter support for GSC controllers has been added
Support for Stage V parameters and lamps has been added

11.2 Removed features

Volvo Singlespeed
Counter and Checksum parameter has been removed
From ECU list 7.5.0 all support of KWP2000 protocol will be removed, this involves ECUs Volvo and Scania.
J1939 protocols DM1 messages will be used instead.

11.3 Bug Repairs

Cummins CM800
Displaying of parameters Load, Spd-Desired, P-Barometric has been fixed
CumminsCM2350
Counter and checksum is now being sent
Cummins GCS
Fault Code 0 is not going to be shown anymore
Doosan ED17
Counter and checksum is now being sent
Deutz EMR5
Problems with speed control has been fixed
GM e-control
Speed request is now being sent in 10ms instead of 20ms period

ECU list 8.1.1 New Features List 25

 Isuzu ECM
Problems with speed control has been fixed
Aftertreatment screen is now being configured automatically
JCB DMC
Aftertreatment screen is now being configured automatically
Jenbacher DIA.NE
Fault Code 0 is not going to be shown anymore
Kohler
Issues with several aftertreatment parameters has been fixed.
MTU ECU7 Direct
Communication speed has ben fixed to 125 bits/s
Standard J939 engine
Counter and checksum is now being sent
Steyr EDC17
Speed request sending is now with correct source address
Yuchai ECU2
Counter and checksum is now being sent
Waukesha EMS
Fault Code 0 is not going to be shown anymore
Waukesha EMS2
Fault Code 0 is not going to be shown anymore
Weichai WISE10B
Speed request is now being sent in 10ms instead of 100ms period

ECU list 8.1.1 New Features List 26

12 Changes in version 7.3.1
12.1 Bug repairs
Iveco NEF & Cursor
Removed problems with speed control when alarm TSC1 Checksum appeared.
JCB Delphi DCM
Fixed bug when parameters SPN 3695 and SPN 3696 weren’t configured or were configured wrong.
MTU MIP4000 and MTU ADEC J1939
Fault code SPN 0 will not be shown in alarm list anymore.

ECU list 8.1.1 New Features List 27

13 Changes in version 7.3.0
13.1 Bug repairs
Caterpillar J1939
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed
Caterpillar ADEM & EMCP
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed
Cummins PGI
Issues with faultcode 639 has been fixed
Guascor LECM E6
Parameter Engine Fuel Flow Rate 1 has been fixed
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed
Iveco MD1
Parameter Generator is Safe for Engine Speed Increase has been fixed
Iveco Vector
Issue that ECU could not be configured in InteliConfig has been fixed
JCB Delphi DCM
Speed Regulation has been fixed
Mahindra
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed
MAN data logger
Oil pressure values are no longer read 100x larger
MTU ADEC J1939
Fixed speed regulation that caused CAN error messages on SAM module.
MTU ADEC J1939 P-engines
Fixed speed regulation that caused CAN error messages on SAM module.
Perkins ECM
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed
Standard J1939 engine
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed
Standard J1939 monitor
Parameter Engine Fuel Valve 1 Intake Absolute Pressure has been fixed

13.2 New Features

New ECU Cummins CM700 has been added
New ECU Weichai Wise 13A has been added
New ECU Waukesha ESM2 has been added

ECU list 8.1.1 New Features List 28

 Agco Power EEM4
Parameter SPN 5246 Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
Caterpillar ADEM A6
DM1 warning lamp parameters has been added
New Stage V related parameters SPN 7580 Aftertreatment Regeneration Engine Speed Allowed
Switch and SPN 7503 - Aftertreatment Engine Load Request has been added
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
Cummins CM2150
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
Cummins CM2350
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
Deutz EMR4
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
Deutz EMR5
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
Hatz EDC
Parameters SPN 3700 Diesel Particulate Filter Active Regeneration Status and SPN 3701 Diesel
Particulate Filter Status has been added for IG200 and IG500 controllers.
Iveco NEF & Cursor
Parameters SPN 109 - Engine Coolant Presure1, SPN 111 - Engine Coolant Level1, SPN 112 -
Engine Coolant Filter Differential Pressure, SPN 170 - Cab Interior Temperature, SPN 171 - Ambient
Air Temperature, SPN 172 - Engine Intake 1 Air Temperature and SPN 176 - Engine Turbocharger Oil
Temperature has been added
Iveco NEF&Cursor is now fully replacing old Iveco NEF&Cursor Tier3
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
JCB Delphi DCM
TSC1 parameters Engine Override Control Mode, Engine Requested Speed Control Conditions and
Override Control Mode Priority has been added
Stage V parameters SPN 514 Nominal Friction - Percent Torque, SPN 515 Engine's Desired
Operating Speed, SPN 108 Barometric Pressure, SPN 171 Ambient Air Temperature, SPN 172
Engine Intake 1 Air Temperature, SPN 3644 Engine Derate Request, SPN 3698 Exhaust System High
Temperature Lamp Command, SPN 3700 Aftertreatment Diesel Particulate Filter Active Regeneration
Status, SPN 3701 Aftertreatment Diesel Particulate Filter Status, SPN 3703 Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch, SPN 4175 Diesel Particulate Filter Active
Regeneration Forced Status, SPN 3719 Aftertreatment 1 Diesel Particulate Filter Soot Load Percent,
SPN 3720 Aftertreatment 1 Diesel Particulate Filter Ash Load Percent, SPN 3721 Aftertreatment 1

ECU list 8.1.1 New Features List 29

 Diesel Particulate Filter Time Since Last Active Regeneration and SPN 1483 Source Address of
Controlling Device for Engine Control has been added
Parameter for Engine stop request has been added
MTU DDEC10
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family
MTU MIP4000
Added text for faultcode SPN 229 – AnalogIOFail
Perkins ECM
Parameter SPN 5246 - Aftertreatment SCR Operator Inducement Severity is now supported in IL3
controllers family

ECU list 8.1.1 New Features List 30

14 Changes in version 7.2.1
14.1 Bug repairs
Scania S8 Allspeed, Scania S8 Singlespeed
Issue with speed control has been fixed

ECU list 8.1.1 New Features List 31

15 Changes in version 7.2.0
The ECU Iveco NEF & Cursor Tier3 has been removed from all ECU lists. Already running installation are not
affected by this change. Use Iveco NEF & Cursor for new installations as well as in case of needs of ECU
configuration update.

15.1 Bug repairs

Reading Engine Total Hours has been fixed in InteliLite controllers.
Isuzu ECM
Definition of the parameter Air Cleaner Clogging Signal has been fixed
Deutz EMR4
Handling of the parameter Start Lock has been improved

15.2 New features

The new ECU support has been added - Iveco MD1
The new ECU support has been added - Caterpillar ADEM A6
The new ECU support has been added - Deutz EMR5
The new ECU support has been added - Weichai Wise 12B
The new ECU support has been added - Doosan G2 EDC17
The new ECU support has been added - Weichai Wise 10B, the support is only in selected controllers.
Please verify it’s support in controller's documentation (NFL) or ask Technical Support
The new ECU support has been added - Leroy Somer AVR CD500, the support is only in selected
controllers. Please verify it’s support in controller's documentation (NFL) or ask Technical Support
Fault codes SPN 0 and SPN 524287 are hidden by default
Parametres DPF Lamp, HEST Lamp, DPF Status, DEF Low Level, SCR Severity, SCR Lamp have been
removed from InteliLite, InteliGen 200, InteliGen500 controller's screens.
Standard J1939 engine
Support of parameters Message Counter and Message Checksum have been added. See particular
controller's manual about support these parameters.
MAN MFR
Speed control & torque control has been updated according to latest specification.
Parameters Selection LLR, Selection EDR have been added
Waukesha ESM
Parameter Current engine operating hours has been added
Scania S8 Allspeed
Parameters Emission-OBD inducement state, Engine Override Control Mode, Engine Requested
Speed Control Conditions, Override Control Mode Priority, Engine Requested Torque/Torque Limit
have been added
Scania S8 Singlespeed
Parameters Emission-OBD inducement state, Engine Override Control Mode, Engine Requested
Speed Control Conditions, Override Control Mode Priority, Engine Requested Torque/Torque Limit
have been added

ECU list 8.1.1 New Features List 32

 Scania S6 Allspeed, Scania S6 Singlespeed
Parameter Engine Requested Torque/Torque Limit have been added
Isuzu ECM
Aftertreatment support has been updated according to the latest manufacturer implementation
Volvo Allspeed
Parameters Transmission Actual Gear Ratio, Transmission Selected Gear, ransmission Current Gear
have been added
List of translated fault codes has been extended
Volvo Singlespeed
Support of Protection Override parameter has been added for InteliGen500, InteliGen 200, InteliLite,
InteliDrive Lite, InteliCompact SPtM and InteliLite-NT controller's family
Parameter Engine Requested Torque/Torque Limit has been added
List of translated fault codes has been extended
Cummins CM850
Parameters Auxiliary Temperature 1, Accelerator Pedal Position 1, Engine Fuel 1 Injector Metering
Rail 1 Pressure, Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible),
Transmission Oil Temperature 1 have been added
Steyr EDC17
The source address of the speed control has been changed to 0x0B
The ECU has been added to all ECU lists
Hatz EDC
The ECU has been added to all ECU lists
Aftertreatment support has been updated according to the last manufacturer implementation
Deutz EMR4
Handling of the parameter Start Lock has been improved
Cummins CM500
The ECU has been added to ECU lists - InteliLite 2015.esl
Parameters Engine Extended Crankcase Blow-by Pressure, Engine Fuel 1 Injector Timing Rail 1
Pressure, Engine Fuel 1 Injector Metering Rail 1 Pressure, Engine Fuel 1 Injector Timing Rail 1
Pressure (backward FW's compatible), Engine Fuel 1 Injector Metering Rail 1 Pressure (backward
FW's compatible) have been added
Guascor LECM E6
Parameters Generator Total Real Power, Desired Power from Generator have been added, follow the
controller's documentation for particular controller's support
Cummins PGI
Parameters Engine Fuel Delivery Pressure, Battery Potential / Power Input 1, Engine Coolant
Pressure 1, Fuel Temperature, Coolant Level Engine Protection Shutdown Override Command,
Requested Engine Control Mode, Generator Alternator Efficiency, Generator Governing Speed
Command, Generator Frequency Selection, Engine Speed Governor Droop, Generator Total Reactive
Power, Generator Overall Power Factor have been added
The default settings of the parameter Governor Gain Adjustment has been changed from 5 to 2

ECU list 8.1.1 New Features List 33

 Cummins CM570
The default settings of the parameter Governor Gain Adjustment has been changed from 5 to 2
Cummins CM850
The default settings of the parameter Governor Gain Adjustment has been changed from 5 to 2
The Weichai EDC has been renamed to Weichai Wise 15A
Cummins CM2350
Parameters Engine Air Filter 1 Differential Pressure, Remote Accelerator Pedal Position,
Transmission Oil Pressure, Transmission Oil Temperature, Trip Average Fuel Rate, Engine Injector
Metering Rail 1 Pressure, Engine Trip Fuel, Fuel Level 1, Fuel Level 2, Engine Coolant Pressure,
Barometric Pressure, Ambient Air Temperature have been added

ECU list 8.1.1 New Features List 34

16 Changes in version 7.1.0
The ECU Scania S6 Allspeed has been removed from all ECU lists. Already running installation are not affected
by this change. Use Scania S6 Allspeed from ver.1794335 for new installations as well as in case of needs of
ECU configuration update.

16.1 Bug repairs

MAN EDC 17
Request for parameter Engine Total Hours of Operation has been fixed. There was a bug in the
destination address.
Scania S6 Allspeed from ver.1794335 and Scania S8 Allspeed
Parameters Nominal Speed Switch 1 and Nominal Speed Switch 2 have been fixed. The parameters
were not sending in some controllers family.
MTU ECU 9
Default configuration of the parameter Generator Frequency Selection has been fixed.
Volvo Singlespeed
The parameter VP70 Idle Speed Select has been fixed. It was inverted
Cummins PGI
A dimension of a parameter Gen Govern Bias has been added.

16.2 New features

The new ECU support has been added - Steyr EDC17
Aftertreatment parameter Aftertreatment SCR Operator Inducement Severity is a part of the default ECU
configuration
Parameters Aftertreatment 1 Diesel Particulate Filter Soot Load Percent, Aftertreatment 1 Diesel
Particulate Filter Ash Load Percent are not visible in controller's screen under ECU inputs in some
controllers family anymore. The controllers value are used instead. For more information follow the
controller's documentation.
The parameter Engine Total Hours of Operation has been updated based on controller's firmware update.
For more information follow the controller's documentation.
Scania S6 Allspeed
The ECU has been removed from the ECU list as the ECU is obsolete. The Scania S6 Allspeed from
ver.1794335 should be configured instead
Volvo Allspeed
Texts of fault codes has been updated and extended
Volvo Singlespeed
Texts of fault codes has been updated and extended
The support of the EMS 2.4 has been added. For more information about the controller's firmware
support follow the controller's documentation
Support of the aftertreatment has been added
New parameter has been added - Disable DEF dosing
Support of the TSC1 has been removed as VP70 is used for speed control instead

ECU list 8.1.1 New Features List 35

 Kubota
New parameters have been added - Parking Brake Switch, Transmission Neutral Switch
Cummins CM570
New parameters have been added - Speed Droop Adjustment, Governor Gain Adjustment
Cummins PGI
Parameter Coolant Level Engine Protection Shutdown Override Command has been added.
Caterpillar ADEM & EMCP
New parameters have been added - Diesel Particulate Filter Regeneration Inhibit Switch, Diesel
Particulate Filter Regeneration Force Switch, Diesel Particulate Filter Lamp Command, Exhaust
System High Temperature Lamp Command, Diesel Particulate Filter Active Regeneration Inhibited
Due to Inhibit Switch, Diesel Particulate Filter 1 Ash Load Percent
Caterpillar J1939
New parameters have been added - Diesel Particulate Filter Regeneration Inhibit Switch, Diesel
Particulate Filter Regeneration Force Switch, Diesel Particulate Filter Lamp Command, Exhaust
System High Temperature Lamp Command, Diesel Particulate Filter Active Regeneration Inhibited
Due to Inhibit Switch, Diesel Particulate Filter 1 Ash Load Percent
Iveco NEF & Cursor
The address of aftertreatment control has been updated
Yanmar TNV
Control of the ECU has been improved
Deutz EMR4
New parameter has been added - Aftertreatment SCR Operator Inducement Severity
Scania S8 Allspeed
New parameter has been added - DPF Regeneration Countdown Timer
Scania S8 Singlespeed
New parameter has been added - DPF Regeneration Countdown Timer
Isuzu ECM
The parameter ECU Operation Time has been updated
Agco Power EEM4
Aftertreatment support has been updated according to the last specification
Cummins CM850
New parameters have been added - Speed Droop Adjustment, Governor Gain Adjustment

ECU list 8.1.1 New Features List 36

17 Changes in version 7.0.0
The ECU Scania S6 Singlespeed has been removed from all ECU lists. Already running installation are not
affected by this change. Use Scania S6 Singlespeed from ver.1794335 for new installations as well as in case of
needs of ECU configuration update.

17.1 Bug repairs

The parameter Oil Temperature has been removed from the default configuration
Caterpillar J1939
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
Caterpillar ADEM & EMCP
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
Cummins CM2150
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
Liebherr LIDEC1
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
MTU DDEC10
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
SISU EEM3 Gen-set
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
Standard J1939 engine
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
Yuchai YC-LBR
Parameter Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible) has been
fixed
Cummins CM2880
The controller's address for the speed control has been fixed
Scania S8 Allspeed
Sending parameters for speed control (DLN1 message) has been fixed
Scania S6 Allspeed from ver.1794335
Sending parameters for speed control (DLN1 message) has been fixed
Cummins CM2350
Automatic configuration of the frequency selection has been fixed according to the controller's FW
specification

ECU list 8.1.1 New Features List 37

 Cummins CM850
Automatic configuration of the frequency selection has been fixed according to the controller's FW
specification
MAN MFR
The parameter Requested Torque is now set to 100%
MTU MIP4000
The reading of the fault codes has been fixed
John Deere
Mapping of parameters Aftertreatment 1 Diesel Particulate Filter Soot Load Percent, Aftertreatment 1
Diesel Particulate Filter Ash Load Percent into the controller's LAI has been fixed

17.2 New features

There is an improvement in default configuration of the ECU in regards of the internal controller resource.
The new ECU support has been added - Mahindra
The new ECU support has been added - Kohler
The new ECU support has been added - YaMZ EDC7
The new ECU has been added - Baudouin WISE15
New ECU Volvo J1587 has been added into the ECU list - Allspeed. This ECU has to be configured in
controller's support multiECU in order to activate the J1587 communication between the controller and the
ECU.
The name of the ECU Cummins MODBUS has been changed to Cummins GCS
The name of the ECU Cummins CM850, CM2150, CM2250 has been changed to Cummins PGI. This
configuration is suitable of any ECU module running with PGI calibration.
Scania S6 Singlespeed from ver.1794335
Speed control over the proprietary TSC1 message is not used anymore. The DLN1 message is used
instead
Scania S8 Allspeed
Speed control over the proprietary TSC1 message is not used anymore. The DLN1 message is used
instead
The KWP2000 diagnostic is not supported anymore
New parameters have been added Aftertreatment Diesel Particulate Filter Status, Diesel Particulate
Filter Active Regeneration Inhibited Due to Inhibit Switch, Diesel Particulate Filter Active Regeneration
Inhibited Due to Clutch Disengaged, Diesel Particulate Filter Active Regeneration Inhibited Due to
Service Brake Active, Diesel Particulate Filter Active Regeneration Inhibited Due to PTO Active, Diesel
Particulate Filter Active Regeneration Inhibited Due to Accelerator Pedal Off Idle, Diesel Particulate
Filter Active Regeneration Inhibited Due to Out of Neutral, Diesel Particulate Filter Active
Regeneration Inhibited Due to Vehicle Speed Above Allowed Speed, Diesel Particulate Filter Active
Regeneration Inhibited Due to Parking Brake Not Set, Diesel Particulate Filter Active Regeneration
Inhibited Due to Low Exhaust Temperature, Diesel Particulate Filter Active Regeneration Inhibited Due
to System Fault Active, Diesel Particulate Filter Active Regeneration Inhibited Due to System Timeout,
Diesel Particulate Filter Active Regeneration Inhibited Due to Temporary System Lockout, Diesel
Particulate Filter Active Regeneration Inhibited Due to Permanent System Lockout, Diesel Particulate
Filter Active Regeneration Inhibited Due to Engine Not Warmed Up, Diesel Particulate Filter Active

ECU list 8.1.1 New Features List 38

 Regeneration Inhibited Due to Vehicle Speed Below Allowed Speed, Exhaust System High
Temperature Lamp Command, Diesel Particulate Filter Active Regeneration Inhibited Due to Low
Exhaust Pressure, Urea Level, Aftertreatment 1 Diesel Particulate Filter Soot Load Percent,
Aftertreatment 1 Diesel Particulate Filter Ash Load Percent, Aftertreatment 1 Diesel Particulate Filter
Soot Load Regeneration Threshold
Scania S8 Singlespeed
Speed control over the proprietary TSC1 message is not used anymore. The DLN1 message is used
instead
The KWP2000 diagnostic is not supported anymore
New parameters have been added Aftertreatment Diesel Particulate Filter Status, Diesel Particulate
Filter Active Regeneration Inhibited Due to Inhibit Switch, Diesel Particulate Filter Active Regeneration
Inhibited Due to Clutch Disengaged, Diesel Particulate Filter Active Regeneration Inhibited Due to
Service Brake Active, Diesel Particulate Filter Active Regeneration Inhibited Due to PTO Active, Diesel
Particulate Filter Active Regeneration Inhibited Due to Accelerator Pedal Off Idle, Diesel Particulate
Filter Active Regeneration Inhibited Due to Out of Neutral, Diesel Particulate Filter Active
Regeneration Inhibited Due to Vehicle Speed Above Allowed Speed, Diesel Particulate Filter Active
Regeneration Inhibited Due to Parking Brake Not Set, Diesel Particulate Filter Active Regeneration
Inhibited Due to Low Exhaust Temperature, Diesel Particulate Filter Active Regeneration Inhibited Due
to System Fault Active, Diesel Particulate Filter Active Regeneration Inhibited Due to System Timeout,
Diesel Particulate Filter Active Regeneration Inhibited Due to Temporary System Lockout, Diesel
Particulate Filter Active Regeneration Inhibited Due to Permanent System Lockout, Diesel Particulate
Filter Active Regeneration Inhibited Due to Engine Not Warmed Up, Diesel Particulate Filter Active
Regeneration Inhibited Due to Vehicle Speed Below Allowed Speed, Exhaust System High
Temperature Lamp Command, Diesel Particulate Filter Active Regeneration Inhibited Due to Low
Exhaust Pressure, Urea Level, Aftertreatment 1 Diesel Particulate Filter Soot Load Percent,
Aftertreatment 1 Diesel Particulate Filter Ash Load Percent, Aftertreatment 1 Diesel Particulate Filter
Soot Load Regeneration Threshold
DaimlerChrysler ADM2
The period for speed control has been changed to 10ms
DaimlerChrysler ADM3
The period for speed control has been changed to 10ms
Yanmar TNV
New paremeters have been added Diesel Particulate Filter Lamp Command, Aftertreatment Diesel
Particulate Filter Passive Regeneration Status, Aftertreatment Diesel Particulate Filter Active
Regeneration Status, Aftertreatment Diesel Particulate Filter Status, Diesel Particulate Filter Active
Regeneration Inhibited Status, Diesel Particulate Filter Active Regeneration Inhibited Due to Inhibit
Switch, Diesel Particulate Filter Active Regeneration Inhibited Due to Clutch Disengaged, Diesel
Particulate Filter Active Regeneration Inhibited Due to Service Brake Active, Diesel Particulate Filter
Active Regeneration Inhibited Due to PTO Active, Diesel Particulate Filter Active Regeneration
Inhibited Due to Accelerator Pedal Off Idle, Diesel Particulate Filter Active Regeneration Inhibited Due
to Out of Neutral, Diesel Particulate Filter Active Regeneration Inhib ited Due to Vehicle Speed Above
Allowed Speed, Diesel Particulate Filter Active Regeneration Inhibited Due to Parking Brake Not Set,
Diesel Particulate Filter Active Regeneration Inhibited Due to Low Exhaust Temperature, Diesel
Particulate Filter Active Regeneration Inhibited Due to System Fault Active, Diesel Particulate Filter
Active Regeneration Inhibited Due to System Timeout, Diesel Particulate Filter Active Regeneration
Inhibited Due to Temporary System Lockout, Diesel Particulate Filter Active Regeneration Inhibited

ECU list 8.1.1 New Features List 39

 Due to Permanent System Lockout, Diesel Particulate Filter Active Regeneration Inhibited Due to
Engine Not Warmed Up, Diesel Particulate Filter Active Regeneration Inhibited Due to Vehicle Speed
Below Allowed Speed, Diesel Particulate Filter Automatic Active Regeneration Initiation Configuration,
Exhaust System High Temperature Lamp Command, Diesel Particulate Filter Active Regeneration
Forced Status, Aftertreatment 1 Diesel Particulate Filter Soot Load Percent, Aftertreatment 1 Diesel
Particulate Filter Ash Load Percent, Aftertreatment 1 Diesel Particulate Filter Time Since Last Active
Regeneration, Engine Throttle Actuator 1 Control Command, Engine Throttle Actuator 2 Control
Command, Engine Fuel Actuator 1 Control Command, Engine Fuel Actuator 2 Control Command,
Aftertreatment 1 Exhaust Temperature 2, Aftertreatment 1 Diesel Particulate Filter Intermediate
Temperature, Aftertreatment 1 Diesel Particulate Filter Differential Pressure, Aftertreatment 1 Exhaust
Temperature 2 Preliminary FMI, Aftertreatment 1 Diesel Particulate Filter Differential Pressure
Preliminary FMI, Aftertreatment 1 Diesel Particulate Filter Intermediate Temperature Preliminary FMI,
Aftertreatment 1 Exhaust Temperature 3, Aftertreatment 1 Diesel Particulate Filter Outlet
Temperature, Aftertreatment 1 Exhaust Temperature 3 Preliminary FMI, Aftertreatment 1 Diesel
Particulate Filter Outlet Exhaust Temperature Preliminary FMI, Aftertreatment 1 Exhaust Temperature
1, Aftertreatment 1 Diesel Particulate Filter Intake Temperature, Aftertreatment 1 Exhaust
Temperature 1 Preliminary FMI, Aftertreatment 1 Diesel Particulate Filter Intake Temperature
Preliminary FMI, Engine Fuel Injection Control Pressure, Engine Fuel 1 Injector Metering Rail 1
Pressure, Engine Fuel 1 Injector Timing Rail 1 Pressure, Engine Fuel 1 Injector Metering Rail 2
Pressure, Aftertreatment 1 Diesel Particulate Filter Intake Pressure (use SPN 3609), Engine Intake
Manifold #1 Pressure, Engine Intake Manifold 1 Temperature, Engine Intake Air Pressure, Engine Air
Filter 1 Differential Pressure, Engine Exhaust Temperature, Engine Coolant Filter Differential Pressure
Aftertreatment parameters Interlock and Acknowledge are now supported in InteliLite controllers
Cummins CM2350
The period for speed control has been changed to 10ms
The aftertreatment support has been upgraded - parameter SCR System Cleaning Inhibited Due to
Inhibit Switch
New parameter Aftertreatment SCR Operator Inducement Severity has been added
Isuzu ECM
New paremeters have been added Aftertreatment Regeneration Inhibit Switch, Aftertreatment
Regeneration Force Switch
MTU ECU 9
Parameter MTU Error Codes is now configurable and can be added into the configuration as a
standard analog input signal
MTU SMART Connect
Parameter MTU Error Codes is now configurable and can be added into the configuration as a
standard analog input signal
Caterpillar J1939
The type of the parameter Requested Engine Control Mode has been changed from input to output
signal
New paremeter has been added Transmission Defuel Actuator
New parameter have been added Transmission Oil Temperature, Engine Crankcase Pressure 1
New texts for fault codes have been added

ECU list 8.1.1 New Features List 40

 Standard J1939 engine
New parameters have been added Transmission Defuel Actuator, Aftertreatment SCR Operator
Inducement Severity has been added
Parameter Aftertreatment SCR Operator Inducement Severity is now included into the default
configuration
The aftertreatment support has been upgraded - parameter SCR System Cleaning Inhibited Due to
Inhibit Switch
New texts for fault codes have been added
Hatz EDC
The aftertreatment support has been updated according to the last engine manufacturer specification
New parameters have been added Aftertreatment 1 Exhaust Gas Mass Flow Rate, Engine Air Filter 1
Differential Pressure, Engine Exhaust Temperature, Aftertreatment 1 Diesel Particulate Filter
Differential Pressure, Aftertreatment 1 Diesel Oxidation Catalyst Intake Temperature, Aftertreatment 1
Diesel Particulate Filter Intake Temperature Preliminary FMI, Aftertreatment Diesel Particulate Filter
Status, Diesel Particulate Filter Active Regeneration Inhibited Due to Out of Neutral, Diesel Particulate
Filter Active Regeneration Inhibited Due to Parking Brake Not Set
Perkins ECM
New parameters have been added Aftertreatment 1 Diesel Exhaust Fluid Tank Volume,
Aftertreatment Diesel Exhaust Fluid Tank Low Level Indicator, Aftertreatment SCR Operator
Inducement Severity, Aftertreatment 1 Diesel Particulate Filter Soot Load Percent, Diesel Particulate
Filter Lamp Command, Exhaust System High Temperature Lamp Command, Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch, Aftertreatment Regeneration Inhibit Switch,
Accelerator Pedal Position 1, Accelerator Pedal Position 2, Actual Engine - Percent Torque, Driver's
Demand Engine - Percent Torque, Nominal Friction - Percent Torque, Aftertreatment 1 Exhaust Gas
Mass Flow Rate, Engine Fuel Delivery Pressure, Engine Coolant Level 1, Engine Crankcase Pressure
1, Engine Intake Air Pressure, Aftertreatment 1 Diesel Particulate Filter Intake Pressure,
Aftertreatment 1 Diesel Particulate Filter Intake Temperature, Engine Filtered Fuel Delivery Pressure,
Engine Filtered Fuel Delivery Absolute Pressure, Engine Fuel Filter Degradation, Engine Fuel 1
Injector Metering Rail 1 Pressure, Ambient Air Temperature, Engine Intake 1 Air Temperature, Engine
Turbocharger 1 Boost Pressure, Aftertreatment 1 Diesel Particulate Filter Outlet Temperature,
Aftertreatment 1 Diesel Particulate Filter Differential Pressure, Engine Intake Manifold #1 Absolute
Pressure, Aftertreatment 1 SCR Intake Temperature, Aftertreatment 1 SCR Outlet Temperature,
Aftertreatment 1 Diesel Exhaust Fluid Concentration, Aftertreatment 1 Intake Gas Sensor 1 at
Temperature, Aftertreatment 1 Intake Gas Sensor 1 Power In Range, Aftertreatment 1 Intake Gas
Sensor 1 Heater Control, Aftertreatment 1 Outlet Gas Sensor 1 at Temperature, Aftertreatment 1
Outlet Gas Sensor 1 Power In Range, Aftertreatment 1 Outlet NOx Sensor 1 Preliminary FMI, Engine
Air Shutoff Command Status, Engine Idle Shutdown has Shutdown Engine, Aftertreatment 1 SCR
System 1 State, Engine Operating State
MAN EDC 17
New parameters have been added Master/Slave Aftertreatment 1 Diesel Particulate Filter Intake
Pressure, Aftertreatment SCR Operator Inducement Severity has been added
The parameter Speed control condition is now configurable and can be added into the configuration in
order to control the droop of the engine

ECU list 8.1.1 New Features List 41

 Cummins CM2150
Parameter Aftertreatment SCR Operator Inducement Severity is now included into the default
configuration
The aftertreatment support has been upgraded - parameter SCR System Cleaning Inhibited Due to
Inhibit Switch
New parameters have been added Engine Exhaust Gas Port 1 Temperature - Engine Exhaust Gas
Port 20 Temperature, Engine Intake Manifold 2, Engine Intake Manifold 3, Engine Intake Manifold 4,
Engine Turbocharger 1 Boost Pressure, Engine Turbocharger 2 Boost Pressure, Aftertreatment SCR
Operator Inducement Severity has been added
MTU DDEC10
Parameter Aftertreatment SCR Operator Inducement Severity is now included into the default
configuration
New parameter Aftertreatment SCR Operator Inducement Severity has been added
Yuchai YC-LBR
Parameter Aftertreatment SCR Operator Inducement Severity is now included into the default
configuration
Iveco NEF & Cursor
New parameters have been added DEF Level, DEF Quality, DEF Technical Failure, Aftertreatment 1
Diesel Particulate Filter Soot Load Percent , Aftertreatment 1 Diesel Particulate Filter Ash Load
Percent , Diesel Particulate Filter Lamp Command , Exhaust System High Temperature Lamp
Command, Aftertreatment SCR Operator Inducement Severity , Aftertreatment Diesel Exhaust Fluid
Tank Low Level Indicator, Diesel Particulate Filter Active Regeneration Inhibited Due to Inhibit Switch,
Aftertreatment Regeneration Inhibit Switch, Aftertreatment Regeneration Force Switch
Deutz EMR4
The stop command has been improved
New parameters have been added Engine Torque Map Selector, Droop Selector
MTU MIP4000
New texts for fault codes have been added
Cummins CM2880
The aftertreatment support has been upgraded - parameter SCR System Cleaning Inhibited Due to
Inhibit Switch
MAN MFR
The aftertreatment support has been upgraded - parameter SCR System Cleaning Inhibited Due to
Inhibit Switch
Caterpillar ADEM & EMCP
New texts for fault codes have been added
John Deere
New parameter Aftertreatment SCR Operator Inducement Severity has been added
Deutz EMR2
New parameter has been added Preheat information
Deutz EMR3
New parameter has been added Preheat information

ECU list 8.1.1 New Features List 42

 Deutz EMR4
New parameter has been added Preheat information
VM Industrial
New parameters have been added Aftertreatment 1 Diesel Exhaust Fluid Tank Volume,
Aftertreatment 1 Diesel Exhaust Fluid Tank Temperature 1
MTU ECU7
New parameters have been added Disable Cylinder Cut Out 1, Disable Cylinder Cut Out 2
Volvo Allspeed
New parameters have been added Max Shift Engine Speed, Target Shift Engine Speed, Max Trolling
Engine Speed, Engine Configuration Code, Calibration State
Speed control (Throttle Position) has been added for InteliLite, InteliGen 200 and InteliGen 500
controllers
Jenbacher Diane
New parameters have been added Jacket Water Temperature, Jacket Water Pressure, Engine Oil
Temperature, Engine Oil Pressure, ExhstGasTemp-Turbocharger, ExhstGasTemp-HeatExchanger,
PlateTempExhstGasHeatExch, Cylinder Exhaust Gas Temp, Heating Water Return Temp, Generator
Power Factor, Generator Frequency, Gener. Current Average, Gener. Voltage Aver. Ph-Ph, Total
Active Output, Total Reactive Output, Setpoint Power Control, Operation Hours Counter, Start
Counter, Fuel Mixture Temperature, Excitation Voltage, Generator Voltage L1-L2, Generator Power,
Generator Reactive Power, Generator Apparent Power, Generator Neutral Current, Boost Pressure
Actual Value, Gasmixer Position, Throttle Valve Position, Turbocharg Bypass Position, Jacket Water
Temperature, Exhaust Gas Temperature Cyl - Exhaust Gas Temperature Cyl20, Charge Temperature
(fuel mixture Temperature), Excitation Voltage, Gnerator Winding Temperature L2, Gnerator Winding
Temperature L3, Generator Bearing Drive End, Generator Bearing Non-Drive End, Speed, Generator
Power, Generator Neutral Current, Boost Pressure Actual Value, Lambda-TECJET

ECU list 8.1.1 New Features List 43

18 Changes in version 6.9.0
18.1 Bug repairs
Agco Power EEM4
Parameter "Cytalyst Tank Temperature" name has been cahnged to "Aftertreatment 1 Diesel Exhaust
Fluid Tank Temperature 1",
Caterpillar ADEM & EMCP
Decimals in certain parameters with psi units has been fixed,
The Issue where “Engine Speed” was not configured into LAI in GenConfig and DriveConfig by default
has been fixed,
Caterpillar J1939
The issue where “Oil Pressure” was configured twice (configured into ECU Input1 and ECU Input2)
with incorrect dimension as °C has been fixed.,
Decimals in certain parameters with psi units has been fixed,
Scania S6 Allspeed
The Issue where multiple Fault Codes over DM1 were not read has been fixed ,
Scania S6 Allspeed from ver.1794335
The Issue where multiple Fault Codes over DM1 were not read has been fixed ,
Decimals in certain parameters with psi units has been fixed,
Scania S6 Singlespeed
The Issue where multiple Fault Codes over DM1 were not read has been fixed ,
Default configuration of parameter „Accelerator Pedal Possition“ in GenConfig and DriveConfig has
been fixed,
Scania S6 Singlespeed from ver.1794335
The Issue where multiple Fault Codes over DM1 were not read has been fixed,
Decimals in certain parameters with psi units has been fixed,
MAN MFR
Decimals in certain parameters with psi units has been fixed,
Scania S8 Allspeed
Decimals in certain parameters with psi units has been fixed,
Scania S8 Singlespeed
Decimals in certain parameters with psi units has been fixed,
Isuzu ECM
The engine control and commanding has been fixed,
Cummins CM2150
Decimals in certain parameters with psi units has been fixed,
Cummins PGI
Decimals in certain parameters with psi units has been fixed,
MTU ECU 9
Decimals in certain parameters with psi units has been fixed,

ECU list 8.1.1 New Features List 44

 Standard J1939 engine
Decimals in certain parameters with psi units has been fixed,
Standard J1939 monitor
Decimals in certain parameters with psi units has been fixed.

18.2 New features

A new ECU support has been added - MAN EDC 17,
A new ECU support has been added - Weichai EDC,
A new ECU support has been added - Hatz EDC,
A new ECU support has been added - Yuchai YC-LBR,
A new ECU support has been added - MTU MIP4000,
A new ECU support has been added - MTU ECU7,
It supports a direct connection of MTU ECU7 with a controller. The supported ECU7 protocol is MCS-
5 (modul 501).
ECU Ford e-control has been added into ECU list - InteliLite 2015 and ECU list - InteliLine,
ECU Yanmar TNV has been added into ECU list - InteliLite 2015, ECU list - InteliLine and ECU list -
InteliNano,
Source parameter of aftertreatment icon “Aftertreatment SCR Operator Inducement Severity” has been
changed,
Agco Power EEM4
Parameter “Stop Request” has been added,
Caterpillar J1939
Parameters „Engine Fuel 1 Injector Metering Rail 1 Pressure”, „Engine Fuel 1 Injector Metering Rail 1
Pressure (backward FW's compatible)”, “Engine Filtered Fuel Delivery Pressure”, „ Aftertreatment 1
Diesel Exhaust Fluid Tank Volume”, “Aftertreatment 1 Diesel Particulate Filter Soot Load Percent” and
“Aftertreatment Diesel Exhaust Fluid Tank Low Level Indicator”, “Engine Exhaust Temperature”,
“Charging System Potential (Voltage)”, “Engine Coolant Level 1”, “Auxiliary Temperature 1”, “Auxiliary
Pressure #1”, “Transmission Output Shaft Speed”, “Transmission Current Gear”, “Transmission
Selected Gear”, “Engine Auxiliary Coolant Temperature”, “Engine Aftercooler Coolant Level”, “Engine
Fuel Leakage 1”, “Engine Fuel Leakage 2”, “EMCP Engine Speed”, “EMCP Engine Coolant
Temperature”, “EMCP Engine Fuel 1 Temperature 1”, “EMCP Key Switch Battery Potential”, “EMCP
Battery Potential / Power Input 1”, “EMCP Engine Oil Filter Differential Pressure”, “EMCP Engine Fuel
Delivery Pressure”, “EMCP Engine Oil Pressure”, “EMCP Protect Lamp”, “EMCP Amber Warning
Lamp”, “EMCP Red Stop Lamp”, “EMCP Malfunction Indicator Lamp” have been added,
Parameter “Generator Total Real Power” has been removed,
Texts of fault codes SPN 1153-1156 have been added,
Isuzu ECM
Proprietary parameter „Engine Torque“ has been added,
Kubota
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,

ECU list 8.1.1 New Features List 45

 Liebherr LIDEC1
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,
MTU DDEC10
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,
SISU EEM3 Gen-set
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,
SISU EEM3 Propulsion
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,
Scania S6 Allspeed from ver.1794335
Parameter “Engine Requested Speed Control Conditions” is now available for user configuration,
Parameters “Key Switch Battery Potential”, “Lamp Test”, “Low Engine Oil Level”, “High Engine Oil
Level”, “Low Urea Level”, “Retarder Selection” and “Engine Wait to Start Lamp” have been added,
Support of DM11 frames, DM1 multiframes on 0x00 address and DM11, DM1 multiframes on 0x3D
address have been added,
Scania S6 Singlespeed from ver.1794335
Parameter “Engine Requested Speed Control Conditions” is now available for user configuration,
Parameters “Engine Oil Level”, “Battery Potential / Power Input 1”, “Low Engine Oil Level”, “High
Engine Oil Level”, “Low Urea Level”, “Retarder Selection” and “Nominal Speed Switch 2” have been
added,
Deutz EMR2
Parameter „Software ID” has been removed,
Deutz EMR3
Parameter „Software ID” has been removed,
DaimlerChrysler ADM3
Parameter „Software Version” has been removed,
Parameter „Source Address” has been removed,
Support of DM11 frames has been added,
DDC DDEC IV/V
Parameter “Red Stop Lamp” has been added,
Perkins 1300
Parameters „Engine Coolant Pressure”, „Engine Coolant Pressure 2”, „Engine Auxiliary Shutdown
Switch“ have been added
Text „AutoStartFail” of fault code SPN 1664 has been added,
Perkins ECM
Parameters „Engine Coolant Pressure”, „Engine Coolant Pressure 2”, „Engine Auxiliary Shutdown
Switch“ have been added
Text „AutoStartFail” of fault code SPN 1664 has been added,

ECU list 8.1.1 New Features List 46

 Cummins PGI
Parameters „Emergency Stop Indication”, “Utility/Isochronous Gain Select” and “Starter Selection” are
now visible in the GenConfig and DriveConfig,
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”,
Parameters “Shutdown Override Fix”, “Frequency Selection Fix”, “Interface Version Informational”,
“Engine Type” and “Protect Lamp” have been added,
Cummins CM2250
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”,
Deutz EMR4
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”,
John Deere
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”,
Kubota
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”,
MTU DDEC10
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”,
Cummins CM500
Support of DM11 frames has been added,
Parameter “Flash Amber Warning Lamp (AWL)” has been added,
Text of fault code SPN 91 is no longer hidden,
Text “IntManigold” of fault code SPN 1043 has been added,
Cummins CM558
Parameter “Flash Amber Warning Lamp (AWL)” has been added,
Cummins CM850
Parameters „Emergency Stop Indication”, “Utility/Isochronous Gain Select” and “Starter Selection” are
now visible in the GenConfig and DriveConfig,
Parameters “Engine Idle Increment Switch”, “Engine Idle Decrement Switch”, “Engine Diagnostics
Test Mode Switch”, “Engine Shutdown Override Switch”, “Frequency Selection” and “Engine Exhaust
Gas Port 17 Temperature” - “Engine Exhaust Gas Port 20 Temperature” have been added,
Cummins CM2150
Parameters “Trip Average Fuel Rate”, “Engine Injector Metering Rail 1 Pressure”, “Auxiliary Pressure
#1”, “Diesel Particulate Filter Active Regeneration Inhibited Due To Inhibit Switch”, “Diesel Particulate
Filter Lamp Command“, „SCR System Cleaning Lamp Command“, „Exhaust System High
Temperature Lamp Command“, „Aftertreatment Diesel Particulate Filter Active Regeneration Status“,
„Aftertreatment Diesel Particulate Filter Status“, „Diesel Particulate Filter Active Regeneration Inhibited
Status“, „SCR System Cleaning Inhibited Due to Inhibit Switch“, „Aftertreatment 1 Diesel Particulate
Filter Soot Load Percent“, „Aftertreatment Diesel Exhaust Fluid Tank Low Level Indicator“,

ECU list 8.1.1 New Features List 47

 „Aftertreatment SCR Operator Inducement Severity“ and „Engine Fuel 1 Injector Metering Rail 1
Pressure (backward FW's compatible)“ have been added,
Cummins CM2250
Parameters “Aftertreatment Regeneration Force Switch” and “Flash Protect Lamp” have been added,
Text “CrankcasDepres“ of SPN 520320 has been added,
Cummins CM2350
Aftertreatment icon “DPF Inhibited” source parameter has been changed to “Diesel Particulate Filter
Active Regeneration Inhibited Due to Inhibit Switch”
Parameter “Engine Requested Torque – High Resolution” has been removed,
Parameters “Engine Auxiliary Shutdown Switch”, “Interface Version Informational”, “Engine Type” and
“Engine Exhaust Gas Port 17 Temperature” - “Engine Exhaust Gas Port 20 Temperature” have been
added,
Parameters "NDE Temperature", "DE Temperature", "U Phase Temperature", "V Phase
Temperature", "W Phase Temperature" and “Engine Requested Torque” have been removed,
Cummins CM2880
Engine speed control has been improved,
Parameter “Batter Potential / Power Input 1” has been added,
Scania S8 Singlespeed
KWP2000 protocol is not available anymore,
Parameters „Torque Limit 1” and „Torque Limit 2” are visible now the GenConfig and DriveConfig,
Parameters „Nominal speed switch 2 (NSSW2)“, „Actual ECA Mode“, „Aftertreatment Clogged
Status“, „Aftertreatment Manual Bypass Request“, „Aftertreatment Port Valve Status“, „Aftertreatment
Bypass Valve Status“, „Aftertreatment Exotherm Status“, „Aftertreatment Manual Bypass Status“,
„Requested Emission Controlled Area Mode“, „Coordinator Stay Alive Request“ and „Version Of DLN
Messages Configuration“ have been added,
Scania S8 Allspeed
KWP2000 protocol is not available anymore,
Parameters „Torque Limit 1” and „Torque Limit 2” are visible in a configuration now,
Parameters „Retarder Selection“, „Aftertreatment Clogged Status“, „Aftertreatment Manual Bypass
Request“, „Aftertreatment Port Valve Status“, „Aftertreatment Bypass Valve Status“, „Aftertreatment
Exotherm Status“, „Aftertreatment Manual Bypass Status“, „Requested Emission Controlled Area
Mode“ and „Coordinator Stay Alive Request“ have been added,
Texts of many fault codes have been added,
MTU ECU 9
Parameters "Requested Engine Control Mode", “Trip Group 1” and “Diesel Particulate Filter Active
Regeneration Inhibited Due to Inhibit Switch” have been added,
Parameters “Coolant Level”, “Air Filter Differential Pressure” and “Fast Flash Malfunction Indicator
Lamp” have been removed,
MTU ADEC J1939
Support of DM1 multiframe and DM11 frames has been added,
Texts of fault codes SPN 415, 416 and 213 have been added,

ECU list 8.1.1 New Features List 48

 Standard J1939 engine
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,
Aftertreatment icon “DPF Inhibited” has been changed to “Diesel Particulate Filter Active
Regeneration Inhibited Due to Inhibit Switch”,
Many new parameters have been added,
Parameters SPN 94, 101, 102, 109, 157, 512, 518, 519, 1176, 1203, 1208, 1213, 1483, 3038_1,
3038_2, 5054, 5246 have been updated,
Standard J1939 monitor
Parameter „Engine Fuel 1 Injector Metering Rail 1 Pressure (backward FW's compatible)” has been
added,
Aftertreatment icon “DPF Inhibited” has been changed to “Diesel Particulate Filter Active
Regeneration Inhibited Due to Inhibit Switch”,
Many new parameters have been added,
Parameters SPN 94, 101, 102, 109, 157, 512, 518, 519, 1176, 1203, 1208, 1213, 1483, 3038_1,
3038_2, 5054, 5246 have been updated,
MAN data logger
Communication timeout has been increased to 5000ms,
MAN MFR
Controller’s date and time is now broadcasted to the ECU. See particular controller’s manual for
supported FW,
Parameters “Driver’s Demand Engine – Percent Torque”, “Flash Protect Lamp”, “Engine Starter
Mode”, “Engine Exhaust Temperature”, “Barometric Pressure”, “Master Engine Turbocharger 1
Turbine Intake Temperature”, “Master Engine Turbocharger 2 Turbine Intake Temperature”, “Slave
Engine Turbocharger 1 Turbine Intake Temperature”, “Slave Engine Turbocharger 2 Turbine Intake
Temperature” have been added,
Texts of many new fault codes have been added.

ECU list 8.1.1 New Features List 49

19 Changes in version 6.8.0
19.1 Bug repairs
Caterpillar J1939 and Caterpillar ADEM & EMCP
a parameter "Total Engine Hours of Operation" has been updated,
Standard J1939 engine and Standard J1939 monitor
high limit of a paramater "Auxiliary Pressure #1"has been fixed,
MAN MFR
value of a parameter "Requested Torque" has been changed to 100%,

19.2 New features

A new controller InteliGen 200 is now supported,
New ECU Yuchai YC-BCR has been added,
New ECU Yuchai YCECU has been added,
The source address of DM11 has been improved across the ECU list,
MAN MFR
new parameters "Seconds", "Minutes", "Hours", "Month", "Day", "Year" have been added. The current
date and time is sending to the ECU. Check particular firmware for support details,
Cummins CM2250
transmitted parameter "Accelerator Pedal Position" has been removed,
parameters "Accelerator Pedal Position 2", "Accelerator Pedal Position 1", "Engine Percent Load At
Current Speed" has been added,
Isuzu ECM
supports Tier4 Final. Check particular firmware for support details,
Standard J1939 engine and Standard J1939 monitor
a new approach of parameters and faulcodes naming is implemented,
parameters "Engine Turbocharger 1 Compressor Intake Pressure", "Engine Turbocharger 2
Compressor Intake Pressure", "Engine Turbocharger 1 Boost Pressure", "Engine Turbocharger 2
Boost Pressure", "Engine Turbocharger 3 Boost Pressure", "Engine Turbocharger 4 Boost Pressure",
"Engine Rated Speed", "Engine Injector Metering Rail 1 Pressure", "Engine Injector Timing Rail 1
Pressure", "Engine's Desired Operating Speed", "Engine Crankcase Pressure" reading and error state
evaluations has been improved. These parameters may not be compatible with some controllers.
Check particular firmware for support details,

reading an alternative dimension (g/h, gal) of parameters "Fuel Rate", "Total Fuel Used" has been
improved,
Deutz EMR4
parameters "Preheat active", "Ready for start / Preheat is done", "Preheat / Coldstart Lamp" have
been added,
parameters "Diesel Exhaust Fluid Tank Level", "Aftertreatment Regeneration Inhibit Switch",
"Aftertreatment Regeneration Force Switch", "DPF Lamp", "High Exhaust System Temperature Lamp

ECU list 8.1.1 New Features List 50

 Command", "DPF Regeneration Urgency Status", "DPF Active Regeneration Inhibited Lamp", "DPF
Active Regeneration Inhibited Due to Inhibit Switch", and Tier4 Final has been added,
Cummins CM2350
a control of "Idle/Rated" switch has been added for InteliLite controllers family,
Cummins CM570
a control of "Idle/Rated" switch has been added for InteliLite controllers family,
Cummins CM850
a control of "Idle/Rated" switch has been added for InteliLite controllers family,
Cummins PGI
a control of "Idle/Rated" switch has been added for InteliLite controllers family,
Volvo Singlespeed
a control of "Idle/Rated" switch has been added for InteliLite controllers family,
Volvo Singlespeed and Volvo Allspeed
a parameter "Aftertreatment 1 Diesel Exhaust Fluid Tank 1 Level" has been added,
John Deere
the lamp Diesel Particulate Filter Regeneration Inhibited is now linked to a parameter "Diesel
particulate filter active regeneration inhibit due to inibit switch"!,
Caterpillar J1939 and Caterpillar ADEM & EMCP
parameters "Engine Throttle Valve 1 Position 1", "Engine Percent Load At Current Speed", "Engine
Oil Pressure", "Engine Intake Manifold 1 Temperature", "Engine Air Filter 1 Differential Pressure",
"Barometric Pressure", "Engine Coolant Pressure 1", "Engine Coolant Temperature", "Battery
Potential / Power Input 1", "Engine Fuel 1 Temperature 1", "Engine Oil Temperature 1", "Engine
Speed", "Engine Total Hours of Operation", "Engine Fuel Shutoff 1 Control", "Gaseous Fuel Correction
Factor", "Engine Turbocharger 1 Boost Pressure", "Engine Exhaust Gas Port 1 Temperature", "Engine
Exhaust Gas Port 2 Temperature", "Engine Exhaust Gas Port 3 Temperature", "Engine Exhaust Gas
Port 4 Temperature", "Engine Exhaust Gas Port 5 Temperature", "Engine Exhaust Gas Port 6
Temperature", "Engine Exhaust Gas Port 7 Temperature", "Engine Exhaust Gas Port 8 Temperature",
"Engine Exhaust Gas Port 9 Temperature", "Engine Exhaust Gas Port 10 Temperature", "Engine
Exhaust Gas Port 11 Temperature", "Engine Exhaust Gas Port 12 Temperature", "Engine Exhaust
Gas Port 13 Temperature", "Engine Exhaust Gas Port 14 Temperature", "Engine Exhaust Gas Port 15
Temperature", "Engine Exhaust Gas Port 16 Temperature", "Engine Exhaust Gas Port 17
Temperature", "Engine Exhaust Gas Port 18 Temperature", "Engine Exhaust Gas Port 19
Temperature", "Engine Exhaust Gas Port 20 Temperature", "Engine Turbocharger 1 Compressor
Intake Temperature", "Engine Turbocharger 1 Turbine Intake Temperature", "Engine Turbocharger 1
Turbine Outlet Temperature", "Engine Oil Filter Intake Pressure", "Engine Shutdown Override Switch",
"Engine Fuel System 1 Gas Mass Flow Rate", "Engine Cylinder 1 Knock Level", "Engine Cylinder 2
Knock Level", "Engine Cylinder 3 Knock Level", "Engine Cylinder 4 Knock Level", "Engine Cylinder 5
Knock Level", "Engine Cylinder 6 Knock Level", "Engine Cylinder 7 Knock Level", "Engine Cylinder 8
Knock Level", "Engine Cylinder 9 Knock Level", "Engine Cylinder 10 Knock Level", "Engine Cylinder
11 Knock Level", "Engine Cylinder 12 Knock Level", "Engine Cylinder 13 Knock Level", "Engine
Cylinder 14 Knock Level", "Engine Cylinder 15 Knock Level", "Engine Cylinder 16 Knock Level",
"Engine Cylinder 17 Knock Level", "Engine Cylinder 18 Knock Level", "Engine Cylinder 19 Knock
Level", "Engine Cylinder 20 Knock Level", "Engine Fuel Specific Gravity", "Engine Fuel Valve 1 Intake
Absolute Pressure", "Engine Fuel Valve 1 Differential Pressure", "Engine Cylinder 1 Ignition

ECU list 8.1.1 New Features List 51

 Transformer Secondary Output", "Engine Cylinder 2 Ignition Transformer Secondary Output", "Engine
Cylinder 3 Ignition Transformer Secondary Output", "Engine Cylinder 4 Ignition Transformer
Secondary Output", "Engine Cylinder 5 Ignition Transformer Secondary Output", "Engine Cylinder 6
Ignition Transformer Secondary Output", "Engine Cylinder 7 Ignition Transformer Secondary Output",
"Engine Cylinder 8 Ignition Transformer Secondary Output", "Engine Cylinder 9 Ignition Transformer
Secondary Output", "Engine Cylinder 10 Ignition Transformer Secondary Output", "Engine Cylinder 11
Ignition Transformer Secondary Output", "Engine Cylinder 12 Ignition Transformer Secondary Output",
"Engine Cylinder 13 Ignition Transformer Secondary Output", "Engine Cylinder 14 Ignition
Transformer Secondary Output", "Engine Cylinder 15 Ignition Transformer Secondary Output",
"Engine Cylinder 16 Ignition Transformer Secondary Output", "Engine Cylinder 17 Ignition
Transformer Secondary Output", "Engine Cylinder 18 Ignition Transformer Secondary Output",
"Engine Cylinder 19 Ignition Transformer Secondary Output", "Engine Cylinder 20 Ignition
Transformer Secondary Output", "Engine Cylinder 1 Ignition Timing", "Engine Cylinder 2 Ignition
Timing", "Engine Cylinder 3 Ignition Timing", "Engine Cylinder 4 Ignition Timing", "Engine Cylinder 5
Ignition Timing", "Engine Cylinder 6 Ignition Timing", "Engine Cylinder 7 Ignition Timing", "Engine
Cylinder 8 Ignition Timing", "Engine Cylinder 9 Ignition Timing", "Engine Cylinder 10 Ignition Timing",
"Engine Cylinder 11 Ignition Timing", "Engine Cylinder 12 Ignition Timing", "Engine Cylinder 13 Ignition
Timing", "Engine Cylinder 14 Ignition Timing", "Engine Cylinder 15 Ignition Timing", "Engine Cylinder
16 Ignition Timing", "Engine Cylinder 17 Ignition Timing", "Engine Cylinder 18 Ignition Timing", "Engine
Cylinder 19 Ignition Timing", "Engine Cylinder 20 Ignition Timing", "Engine Desired Ignition Timing 1",
"Engine Actual Ignition Timing", "Engine Fuel Valve 1 Position", "Engine Starter Mode", "Specific Heat
Ratio", "Engine Throttle Actuator 1 Control Command", "Engine Turbocharger Compressor Bypass
Actuator 1 Command", "Requested Engine Control Mode", "Engine Operating State", "Time
Remaining in Engine Operating State", "Engine Oil Priming Pump Switch", "Engine Oil Priming State",
"Engine Emergency (Immediate) Shutdown Indication", "Engine Derate Request", "Engine
Turbocharger Compressor Bypass Actuator 1 Position", "Engine Exhaust Temperature Average",
"Engine Exhaust Bank 2 Temperature Average", "Engine Exhaust Bank 1 Temperature Average",
"Engine Intake Manifold 1 Absolute Pressure (High Resolution)", "Engine Throttle Valve 1 Differential
Pressure", "Engine Oil Filter Differential Pressure (Extended Range)", have been added or renamed.

ECU list 8.1.1 New Features List 52

20 Changes in version 6.7.0
20.1 Bug repairs
John Deere
Tier4 supported has been improve
Scania S8 Allspeed, Scania S8 Singlespeed
A wrong identification of DLN1 message has been fixed
Cummins CM2880, JCB Delphi DCM, MTU DDEC10, MTU ECU 9, Standard J1939 engine, Standard
J1939 monitor
Parameters "Aftertreatment 1 Intake NOx" and "Aftertreatment 1 Outlet NOx" have been updated

20.2 New features

MTU ADEC J1939
Parameters "EAC/Engine Auxliliary Coolant Pressure" and "EFL/P1 / Coolant Pressure" have been
added
Isuzu ECM
Tier4F support for InteliLite controller family has been added
Iveco NEF & Cursor, Iveco NEF & Cursor Tier3
A new fault codes are translated to the text
Caterpillar J1939,Caterpillar ADEM & EMCP
A new fault codes are translated to the text
Scania S6 Singlespeed,Scania S6 Singlespeed from ver.1794335
Contifuration of the frequency selection is done automatically now for InteliGenNT,
InteliSysNTcontroller family
MTU EIM
Parameters "Protect Lamp","Malfunction Lamp","Flash Malfunction Indicator Lamp","Flash Red Stop
Lamp","Flash Amber Warning Lamp" have been added
GM MEFI6
Parameters "Spark Advance","Bank_A Close Loop Fuel Control","O2 Sensor_A1 Raw Voltage","O2
Sensor_A1 Rich/Lean Cross Counts","Bank_A BLM Cell","Bank_A BLM[Cell] Value","Bank_A Fuel
Mult","Bank_B Close Loop Fuel Control","O2 Sensor_B1 Raw Voltage","O2 Sensor_B1 Rich/Lean
Cross Counts","Bank_B BLM Cell","Bank_B BLM[Cell] Value","Bank_B Fuel Mult","O2 Sensor_A2
Raw Voltage","O2 Sensor_B2 Raw Voltage","Throttle Position","CurrentRpmRatedTorque","Cam-W
Angle","Reference Cam-W Angle" have been added
John Deere
A new parameter "Engine Requested Torque/Torque Limit" has been added

ECU list 8.1.1 New Features List 53

21 Changes in version 6.6.0
21.1 Bug repairs
Parameter "Oil Pressure" reading in InteliLite 2015 resolved.
Isuzu ECM
Parameters conflict between "StopReq" and "EngProtHoldSig" resolved.
Parameters "TotalOperationHours", "Battery potential", "Electrical potential" reading resolved
Cummins CM2350
Configuration problems in LiteEdit 2015 resolved

21.2 New features

A new ECU Cummins CM2880 is now supported
Isuzu ECM
Tier4Final support for InteliGen and InteliSys family controller has been added
Volvo EDC7 Allspeed KWP2000
Text of fault codes has been extended.
Cummins CM850
New parameters "CurrentGear", "SelectedGear", "OutShaftSpeed" have been added
Caterpillar J1939
New paremeters have been added "IntervoolerTemp", "CurrentGear", "SelectedGear",
"OutShaftSpeed"

ECU list 8.1.1 New Features List 54

22 Changes in version 6.5.0
22.1 Bug repairs
Dimension of the parameters "Air Filter Differential Pressure" and "Barometric Pressure" has been
updated and unified
MTU SMART Connect
The parameter "Requested speed" is now configured automatically in the GenConfig PC software
Scania S6 Allspeed
Speed control in InteliDrive Litehas been fixed
Scania S6 Allspeed from ver.1794335
Speed control in InteliDrive Lite has been fixed
MAN data logger
The parameters related to the aftertreatment have been removed
Speed control of Cummins CM2150, Kubota, MTU DDEC10, VM Marine and Standard J1939 enginehas
been improved

22.2 New features

A new ECU Guascor LECM E6 is now supported
A new ECU Cummins CM2350is now supported
Yanmar TNV is now available in ECU list - Gensets.esl and ECU list - InteliLite2015.esl
DaimlerChrysler ADM2 and DaimlerChrysler ADM3 is now available in ECU list - Gensets.esl
Dimension of parameter "Barometric Pressure" has been uniformed to kPa
Handling of the DM11 and DM3 has been unified. From now on only DM11 (clear diagnostic information
for active DTCs) is used by ComAp controllers .
Automatic control of parameters "Nominal Speed 1" and "Nominal Speed 2" of Scania S6 Singlespeed
and Scania S6 Singlespeed from ver.1794335is available for:
InteliGenNT, InteliSysNT controllers since version 3..0
InteliLite controllers since version 1.2.0
John Deere
New paramater has been added "SCR Operator Inducement Severity"
MTU SMART Connect
The refresh rate of the speed command has been increased
Control of parameter "Speed Demand Switches" has been improved
New text of the fault code SPN520875
New text of the fault code SPN521128
MTU ECU 9
New parameter "DEF Tank 1 Low Level Indicator" has been added
New text of the fault code SPN521026
New text of the fault code SPN521027

ECU list 8.1.1 New Features List 55

 Perkins ECM
New paremeters have been added "Turbocharger Compressor Bypass Actuator 1 Position", "Fuel
Valve 1 Position", "Fuel Valve 2 Position", "Requested Fuel Valve 1 Position", "Requested Fuel Valve
2 Position", "Fuel Valve 1 Intake Absolute Pressure", "Fuel Valve Differential Pressure", "Air to Fuel
Differential Pressure", "Air to Fuel Differential Pressure", "Desired Rated Exhaust Oxygen", "Desired
Rated Exhaust Oxygen", "Desired Rated Exhaust Oxygen", "Desired Exhaust Oxygen" and "Actual
Exhaust Oxygen"
Automatic configuration of the parameter "Speed Bias Reference" in GenConfig PC software has been
improved
GM MEFI6
Parameter "Percent Load" has been removed as is not available in the ECU
GM e-control LCI, GM e-control
New parameters have been added "Long-term Fuel Trim - Bank 1", "Short-term Fuel Trim - Bank 1",
"Engine Exhaust Bank 1 O2 Sensor Closed Loop Operation", "Long-term Fuel Trim - Bank 2", "Short-
term Fuel Trim - Bank 2", "Engine Exhaust Bank 2 O2 Sensor Closed Loop Operation" and "Engine
Actual Ignition Timing"
Agco Power EEM4
New parameters have been added "DEF Tank 1 Level", "DPF Reg. Inhibit Switch" and "DEF Tank 1
Low Level Indicator"
Parameter "DEFTankLvlLamp" is not available anymore
Cummins MODBUS
New parameters have been added "Battery Voltage", "Coolant Pressure", "Fuel Supply Pressure" and
"Fuel Temperature"
Volvo Allspeed
The source address of parameters "DEF Tank 1 Level", "DEF Tank 1 Low Level Indicator", "Operator
Inducement Severity" has been changed
The description of the ECU in the PC software has been updated
Control of parameters "Calibration State" and "Active Station" has been improved
Caterpillar J1939, Caterpillar ADEM & EMCP
New parameter "Sea Water pmp Outlet Pressure" has been added
Volvo Singlespeed
The source address of parameters "DEF Tank 1 Level", "DEF Tank 1 Low Level Indicator", "Operator
Inducement Severity" has been changed
The description of the ECU in the PC software has been updated

ECU list 8.1.1 New Features List 56

23 Changes in version 6.4.0
23.1 Bug repairs
Iveco Vector
an alternative dimension PSI has been added for parameter "Oil pressure"
Parameter name and/or low limit of "Crankcase Pressure" has been modified
a decimal of parameter "Fuel level" has been fixed,

23.2 New features

ECU list - DriveNano.esl has been removed. TheECU list - Allspeed.esl is in used in DriveEdit PC
software instead,
A new ECU support has been added - Cummins CM2350,
A new ECU support has been added - Cummins CM2150,
A new ECU support has been added - Liebherr LIDEC1,
A new ECU support has been added - MTU EIM,
A name of the ECU "Volvo EMSI Singlespeed / EMSII" has been change to "Volvo Singlespeed",
A name of the ECU "Volvo EMSI Allspeed" has been changed to "Volvo Allspeed",
MTU SMART Connect
a text of fault codes has been added,
Caterpillar J1939
a text of faul codes SPN 95 and 173 has been added,
new parameters "Aux Valve 15 Fail Safe Mode Command", "Auxiliary Coolant Pressure", "Engine
Auxiliary Coolant Temperature", "Coolant Pressure", "Engine Intercooler Coolant Level", "Engine
Aftercooler Coolant Level", "Pre-filter Oil Pressure", "Fuel Leakage", "Fuel Leakage 2", "Exhaust Gas
Temperature" have been added,
Ford e-control
speed control of the ECU has been modified for a better performance,
Deutz EMR3
a new parameter "Fuel delivery pressure" has been added,
SISU EEM3 Gen-set
a new parameter "Injector Metering Rail Pressure" has been added,
John Deere
a new parameter "Override control mode" has been added. InteliDrive DCU controller can control the
speed or limit the torque based on this parameter configuration,
Caterpillar ADEM & EMCP
a new parameter "Engine Intercooler Coolant Level" has been added,
JCB Delphi DCM
parameters(see table below) have been added.

ECU list 8.1.1 New Features List 57

 Parameter name SPN type
Intake NOx 3216 ANAIN
AT1 Intake O2 3217 ANAIN
Aftertreat1 ExhGas Temp 1 3241 ANAIN
Outlet NOx 3226 ANAIN
AT1 Outlet O2 3227 ANAIN
DEF Tank 1 Level 1761 ANAIN
Diesel Exhaust Fluid Tank 1 Temperature 3031 ANAIN
Flash Malfunction Lamp 3038 ANAIN
Flash Red Stop Lamp 3039 ANAIN
Flash Amber Warning Lamp 3040 ANAIN
Aftertreatment Lamp Status 517640 ANAIN
Inducement Level 517641 ANAIN
Refresh Status Byte 517649 ANAIN
SCR Monitor 517650 ANAIN
Successful Running Refreshes 517651 ANAIN
Successful Stationary Refreshes 517652 ANAIN
Red Stop Lamp 623 BININ
Amber Warning Lamp 624 BININ
Malfunction Lamp 1213 BININ
Protect Lamp 987 BININ
Bank 1 Intake Dew Point 3237 BININ
Bank 1 Exhaust Dew Point 3238 BININ
Bank 2 Intake Dew Point 3239 BININ
Bank 2 Exhaust Dew Point 3240 BININ
DPF Regeneration Inhibit Switch 3695 BINOUT
DPF Regeneration Force Switch 3696 BINOUT

ECU list 8.1.1 New Features List 58

24 Changes in version 6.3.1
24.1 New features
A new ESL "ECU list - InteliLite2015.esl" for InteliLite controller's family has been added.

ECU list 8.1.1 New Features List 59

25 Changes in version 6.3.0
25.1 Bug repairs
John Deere
a command name "CleaningAllow" has been changed to "CleanNotAllow" to follow its functionality

25.2 New features

Parameters "Fast Flash Malfunction Indicator Lamp" and "Flash Malfunction Indicator Lamp" (SPN3038),
"Flash Red Stop Lamp" and "Fast Flash Red Stop Lamp" (SPN3039), "Flash Amber Warning Lamp" and
"Fast Flash Amber Warning Lamp" (SPN3040), "Flash Protect Indicator Lamp" (SPN3041) and
"Malfunction Lamp" (SPN1213) were added or modified in every SAE J1939 based ECU to support
Tier4final functionality of the controller.
VM Marine
The "Requested speed" parameter was modified to improve performance of engine speed control.
Standard J1939 engine & Standard J1939 monitor
a support of parameters "SCR System Cleaning Lamp Command" and "SCR System Cleaning
Inhibited Due to Inhibit Switch"were added

ECU list 8.1.1 New Features List 60

26 Changes in version 6.2.0
26.1 Bug repairs
Isuzu ECM
a name of the parameter "Turbo actual opening" has been corrected,
GM MEFI6
a decimal of paramater "Fuel level" has been fixed,
JCB Delphi DCM
a decimal of parameter "Fuel level" has been fixed,
Kubota
a control of aftertreatment has been improved.

26.2 New features

A new ECU support has been added - MTU ECU 9,
MTU ADEC J1939
parameters "AL Combined Alarm Yellow" and "AL Combined Alarm Red" have been added,
Caterpillar J1939
parameters "Transmission Output Shaft Speed" and "Transmission Current Gear" have been added,
Cummins CM850
parameters "Transmission Output Shaft Speed" and "Transmission Current Gear" have been added,
MTU DDEC10
commands "Start Request" and "Stop Request" have been added,
MTU SMART Connect
parameters "Exhaust Gas Port 17 Temp", "Exhaust Gas Port 18 Temp", :Exhaust Gas Port 19 Temp"
and "Exhaust Gas Port 20 Temp" have been added.

ECU list 8.1.1 New Features List 61

27 Changes in version 6.1.0
27.1 New features
A new ECU support has been added - Kubota,
MTU SMART Connect
values "Fuel Delivery Pressure", "Exhaust Gas Port 1 Temp" to "Exhaust Gas Port 16 Temp", "Sea
Water Pump Outlet Pressure", "P-Lube Oil Redundant", "T-Coolant Redundant" have been added,
John Deere
improvment of Tier4 functionality for InteliDrive Lite controllers.

ECU list 8.1.1 New Features List 62

28 Changes in version 6.0.0
28.1 Bug repairs
NT
Cummins CM850, Cummins CM570, Cummins PGI configuration - support for InteliLite controller has
been improved,
Deutz EMR3 configuration - behavior of function "Start Lock" and speed control for InteliCompactNT
controller were improved,
GM MEFI6, MTU SMART Connect, DaimlerChrysler ADM3 configuration - speed control for
InteliCompactNT controller has been improved,
Scania S6 Singlespeed configuration - proprietary (TSC1) speed control for InteliGenNT , InteliSysNT,
InteliDrive DCU and InteliDrive Mobile controller has been improved,
Scania S8 Allspeed, Scania S8 Singlespeed configuration - format of value "Urea level inducement state"
has been changed,
Caterpillar ADEM & EMCP
a value "Right Air Filter Restriction" has been renamed to "Air Filter 2 Differential Pressure",
a value "Air Filter Differential Pressure" has been renamed to "Air Filter 1 Differential Pressure",
reading of values "Exhaust Gas Temp - Right Manifold", "Exhaust Gas Temp - Left Manifold",
"Turbocharger 1 Intake Temp" and "Turbocharger 2 Intake Temp" were improved,
Isuzu ECM
values "Boost Pressure", "Intake Manifold Temp", "Catalyst inlet gas temp" have been modified
according to a new Isuzu specification,
a value "Air Intake Pressure" has been removed according to a new Isuzu specification,
a value "Exhaust Gas Temp" has been renamed to "DPF filter Inlet Gas Temp" according to a new
Isuzu specification,
Caterpillar J1939
reading of values "Exhaust Gas Temp - Right Manifold", "Exhaust Gas Temp - Left Manifold",
"Turbocharger 1 Intake Temp" and "Turbocharger 2 Intake Temp" have been improved,
Cummins CM850
reading/control of "Crankcase Pressure" and "Shutdown Override CC" has been improved,
Iveco NEF & Cursor
broadcasted data of InteliGenNT, InteliSysNT, InteliDrive DCU and InteliDrive Mobile controller when
no analog output is configured has been changed.

28.2 New features

ECU list Mobile has been removed. It is now distributed as a particular installation package,
A new ECU support has been added - MTU DDEC10,
A new ECU support has been added - AGCO Power EEM4,
A new ECU support has been added - MAN data logger,
A new ECU support has been added - Volvo EDC7 Allspeed KWP2000,
A new ECU support has been added - Standard J1939 monitor,
A new ECU support has been added - Iveco NEF & Cursor Tier3,

ECU list 8.1.1 New Features List 63

 NT
Added support of value "Total Fuel Used" for InteliLite , InteliDrive Lite and InteliCompactNT controllers,
Automatic configuration of value "Engine Oil Pressure" from the ECU as a main source for the controller
has been added,
Caterpillar ADEM & EMCP
values "Total Engine Hours", "Air Inlet Temperature", "Alternator Bearing 1 Temperature", "Alternator
Bearing 2 Temperature", "Alternator Winding 1 Temperature" to "Alternator Winding 3 Temperature",
"Pre-filter Oil Pressure", "Auxiliary Coolant Pressure", "Turbocharger 1 Intake Temperature",
"Turbocharger 2 Intake Temperature", "Turbo 1 Inlet Pressure", "Turbo 2 Inlet Pressure", "Fuel Filter
(Suction) Intake Absolute Pressure", "Fuel Temperature 2" and "Coolant Pressure" have been added,
a request for "Total Engine Hours" is now broadcasted by the controller,
extended text support of fault codes (SPN 137, 1137 - 1152, 1203, 1231, 1239, 4193) have been
added. New hidden fault codes of SPN 234, 1656 has been added,
names of values have been modified from "Right Turbo Inlet Pressure" to "Turbo 1 Inlet Pressure" and
from "Left Turbo Inlet Pressure" to "Turbo 2 Inlet Pressure",
Cummins CM570
an automatic configuration of "Frequency Selection" based on a controller setpoint "Nominal freq" for
InteliGenNT and InteliSysNTcontrollers has been added,
an automatic configuration of limits of "Speed Bias Reference" for InteliGenNT and
InteliSysNTcontrollers has been added. The limit is set to -10% to +10% of nominal frequency,
Cummins CM850
an automatic configuration of "Frequency Selection" based on a controller setpoint "Nominal freq" for
InteliGenNT and InteliSysNTcontrollers has been added,
an automatic configuration of limits of "Speed Bias Reference" for InteliGenNT and
InteliSysNTcontrollers has been added. The limit is set to -10% to +10% of nominal frequency,
extended text support of fault codes (SPN 166, 611, 612, 633, 697, 723, 1075, 1347, 2802, 3509,
3510, 3511, 3512, 3597, 3938, 4182, 4183) has been added,
values "Auxiliary Pressure #1", "Electrical Potential", "Battery Potential (Voltage)", "Exhaust Gas
Temperature - Right Manifold", "Exhaust Gas Temperature - Left Manifold", "Intake Manifold 2
Temperature" to "Intake Manifold 6 Temperature", "Pre-filter Oil Pressure", "Turbocharger 1 Boost
Pressure" to "Turbocharger 4 Boost Pressure", "Percent Load", "Total Fuel Used", "Trip Fuel" have
been added,
new command "Engine Auxiliary Shutdown Switch" has been added,
a value "Crankcase Pressure" has been modified
Cummins PGI
an automatic configuration of "Frequency Selection" based on a controller setpoint "Nominal freq" for
InteliGenNT and InteliSysNTcontrollers has been added,
an automatic configuration of limits of "Speed Bias Reference" for InteliGenNT and
InteliSysNTcontrollers has been added. The limit is set to -10% to +10% of nominal frequency,
an automatic configuration of limits of "Generator Governing Bias" for InteliGenNT and
InteliSysNTcontrollers has been added. The limit is set to -10% to +10% of nominal frequency,
a value "Tank Low Level Indicator" has been renamed to "DEF Tank 1 Low Level Indicator,
Cummins CM2250
a value "Tank Low Level Indicator" has been renamed to "DEF Tank 1 Low Level Indicator"

ECU list 8.1.1 New Features List 64

 Isuzu ECM
values "Target engine speed", "Fuel injection quantity level", "Engine percent torque", "Boost
Pressure", "Ignition key switch", "DPF SwitchKnd", "DPF SwitchUns", "RegAuxLoadReq1",
"RegAuxLoadReq2", "StartCutRelay", "EGRGasTmpWrn", "DiffPressJudg1", "Commonrail Pressure",
"Instruction engine speed", "Commonrail Diff Pressure", "InAirBstTmpWrn", "ExhstGasTmpWrn",
"IntAirTmpWrn", "FuelFltrClogg", "EngOilPresDrop", "BoostTmpRise", "FuelTmpRise",
"ClntTmpRise", "OverrunWrn", "EmerSDoperSig", "Glow signal", "StarterSwitch", "DPF
GrLampMode", "DPF AmLampMode", "DPF RegLampReq", "DPF BuzzerMode", "DPF IndiStat",
"DPF RegenFlag", "Atmospheric pressure", "T-Ambient", "PCode", "Turbo actual opening", "Total
operating hour", "Fuel Temperature" and command "EngineModel/SN" have been added,
extended text support of fault codes (SPN 675, 1131, 1381, 158, 10050 - 10052, 10045, 10046,
10048, 697, 10032, 10033) has been added,
Iveco NEF & Cursor
a value "Catalyst Tank Level" has been renamed to "DEF Tank 1 Level "
GM MEFI4/MEFI5B
extended text support of fault codes (SPN 38, 96, 108, 175, 627, 630, 651 - 658, 3563, 65560 - 65568,
65570 - 65573, 65580 - 65582, 65590 - 65602, 65604, 65605, 65610, 65613, 65615, 65616, 65618,
65620, 65621, 65671 - 65678, 65690, 65710, 65723 - 65726, 66001 - 66022, 66025, 66026, 66030,
66035, 66040- 66043) has been added,
John Deere
period of broadcasted data by the controller has been improved,
MTU ADEC J1939 P-engines
values "AirFlap A wire break", "AirFlap B wire break", "ASO Voltage to Lo on Relay", "ASO Watchdog
Relay", "Emergency Stop Input 2", "Emergency Stop Input 3", "Emergency Stop Input 4", "ASO Flap A
Feedback Contact", "ASO Flap B Feedback Contact", "WB SaSy Emergency Stop Output", "EMU
Emergency Stop-Open Circuit" have been added,
Standard J1939 engine
support of many new values has been added,
Scania S8 Allspeed
support of DM1 fault codes reading has been added,
Scania S8 Singlespeed
support of DM1 fault codes reading has been added,
Volvo Allspeed
a new proprietary KWP2000 fault code protocol has been added. It is supported only in InteliDrive
DCUcontroller. For more information please look at particular controller documentation,
a value "Tank Low Level Indicator" has been renamed to "DEF Tank 1 Low Level Indicator"
Volvo Singlespeed
a value "Tank Low Level Indicator" has been renamed to "DEF Tank 1 Low Level Indicator"
Automatic configuration of history header has been added for these ECU values :

ECU list 8.1.1 New Features List 65

 Value Name History Header
Engine Speed Erpm
Fuel Rate Eflr
Coolant Temperature Eclt
Intake Temperature Eint
Oil Pressure Eoil
Percent Load Eld
Boost Pressure Ebst
Total Engine Hours Ehr

ECU list 8.1.1 New Features List 66

29 Notes
29.1 Software compatibility
Version 8.1.1 can be imported into GenConfig, DriveConfig, LiteEdit, LiteEdit2015, DriveEdit, NanoEdit,
ECUDiag as a standard firmware package. It must be used with the following versions of ComAp PC
software:
GenConfig ver. 3.14.2 or newer
DriveConfig ver. 3.13.1 or newer
LiteEdit ver. 6.0.0 or newer
InteliConfig ver. 2.34.0 or newer
DriveEdit ver. 1.1.1 or newer
NanoEdit ver. 2.1.0 or newer

29.2 ECU list content

ESC file ID Version Description
Adelsystem CB12245AJ supports Smart Battery
Adelsystem_CB12245AJ.esc 279 8.1.1
Charger via CAN bus communication.
AGCOpower (formerly SISU diesel) 84WIP, 44AWF
Agco_Power_EEM4.esc 116 8.1.1 allspeed or 84WIG gen-set engines with EEM4
engine control unit. Tier4Final support.
The CD200D system can operate as a single-firing
or double-firing (firing on exhaust stroke) system up
to sixteen (16) cylinders. CD200, CD200EX,
Altronic_CD200.esc 176 8.1.1
CD200EVS, CD200D, CD200DR, NGI-1000 and
NGI-1000RC units are supported. Modbus Address
1
The CD200D system can operate as a single-firing
or double-firing (firing on exhaust stroke) system up
to sixteen (16) cylinders. CD200, CD200EX,
Altronic_CD200_mdb.esc 1031 8.1.1
CD200EVS, CD200D, CD200DR, NGI-1000 and
NGI-1000RC units are supported. Modbus Address
1
Altronic NGI-1000RC ignition system on Modbus
Altronic_NGI-1000.esc 221 8.1.1
address 11
Altronic NGI-1000RC ignition system on Modbus
Altronic_NGI-1000_mdb.esc 1032 8.1.1
address 11
Baudouin 12M33/12M55/16M33, 12M55NG and
Baudouin_LECM_E6.esc 225 8.1.1 16M33NG Gas engines equipped with Woodward
LECM E6 electronic control unit.
Baudouin
6M33NG/6M21NG/6M16NG/6M11NG/4M11NG and
Baudouin_SECM70.esc 288 8.1.1
12M33NG gas engines equipped with Woodward
SECM70 electronic control unit.
The WISEC10B is designed for 6 cylinders or 8
cylinders diesel engines. For the application of 12
Baudouin_WISE10B.esc 179 8.1.1
cylinders or 16 cylinders diesel engines, two
WISE10B and a master-slave structure is needed.

Baudouin_WISE15.esc 179 8.1.1 Baudouin diesel engines 4M06G45/6, 4M06G50/5,

ECU list 8.1.1 New Features List 67

 6M21G400/6, 6M21G500/5, 6M33G660/6,
6M33G825/5 equipped by the WISE15 control unit.
Under tests!
Caterpillar gen-sets with ADEM engine control unit
Caterpillar_ADEM_&_EMCP.esc 17 8.1.1 and EMCP ver.3 or ver.4 control panel. No engine
control by the controller is available.
Caterpillar engines C4.4, C7.1 and C9.3B with
Caterpillar_ADEM_A6.esc 192 8.1.1
ADEM A6 ECU, supporting Tier4 Final and Stage V.
Caterpillar ACERT engines (C18, C15, C13, C11,
C9, C7.1, C6.6, C4.4) and others with ADEM engine
Caterpillar_J1939.esc 10 8.1.1
control unit. Tier 4 monitoring and control is
available.
Cummins engines ISDe, ISLe, ISX, ISX13 China
Cummins_CM2150.esc 134 8.1.1 stage 3 series with CM2150E engine control unit.
Tier4Interim support. Under tests!
Cummins industrial engines series ISB, ISX with
Cummins_CM2250.esc 59 8.1.1 CM2250 engine control unit. Tier 4 monitoring and
control is available. Tier4Final support.
Cummins engines QSF3.8, QSB4.5, QSB6.7,
QSL8.9, QSX15, QSK95 and QSG12 with CM2350
Cummins_CM2350.esc 101 8.1.1
control unit. Tier 4 Final monitoring and control is
available. Tier4Final support.
Cummins industrial diesel engines QSB4.5, QSB
Cummins_CM2350_industrial.esc 222 8.1.1 6.7, QSL9, QSX15 and QSG12, equipped with
CM2350 ECU. Tier 4Final support.
Cummins engines ISDe NS3, ISLe NS3, ISBe NS4,
Cummins_CM2880.esc 154 8.1.1 ISC3 NS4, ISDe NS4, ILSe NS4, ISZ NS4 series
with CM2880 engine control unit. Under tests!
Cummins industrial engines QSK19, QSK23,
Cummins_CM500.esc 57 8.1.1 QSK45, QSK60, QSK78 engines with CM500
engine control unit.
Cummins_CM558.esc 33 8.1.1 Cummins gas engines with CM558 unit.
Cummins engines QSM, QSX, ISM series with
Cummins_CM570.esc 4 8.1.1 CM570 engine control unit. Required G-Drive or
Industrial calibration according to application.
Cummins engines with QSK19G, QSK60G,
Cummins CM700.esc 199 8.1.1
QSV91G with CM700 engine control unit.
Cummins industrial engines ISB, ISBe series with
Cummins_CM800.esc 67 8.1.1
CM800 engine control unit.
Cummins engines QSL, QSB, QSK, QST, series
with CM850 engine control unit. Required G-Drive or
Cummins_CM850.esc 26 8.1.1
Industrial calibration according to application.
Tier4Final support.
Cummins engines with GCS engine control unit.
Cummins_GCS.esc 5 8.1.1
Communication interface RS485
Cummins PGI 1.1 engines - QSB, QSL series with
CM2250 engine control unit; QSK series with
Cummins_PGI.esc 43 8.1.1 CM2150 engine control unit; QSB, QSL, QSM series
with CM850 engine control unit. Tier 4 monitoring
and control is available. Tier4Final support.
DaimlerChrysler 500, 900, 450 series engines
DaimlerChrysler_ADM2.esc 24 8.1.1 equipped with PLD-MR engine control unit and
ADM2 vehicle control adaptation module.

ECU list 8.1.1 New Features List 68

 DaimlerChrysler 500, 900, 450 series engines
DaimlerChrysler_ADM3.esc 42 8.1.1 equipped with PLD-MR engine control unit and
ADM3 vehicle control adaptation module.
Detroit Diesel or MTU series 60 engines equipped
DDC_DDEC_IV/V.esc 9 8.1.1
DDEC IV or DDEC V engine control unit.
Deutz engines series 1000 with EMR2 engine
Deutz_EMR2.esc 8 8.1.1
control unit (similar to Volvo EDC4).
Deutz engines series 2000 with EMR3 engine
Deutz_EMR3.esc 25 8.1.1
control unit.
Deutz engines TDC 3.6, TDC 4.1, TDC 6.1, TDC 7.8,
TDC 12 or others with EMR4 control unit. Tier 4
Deutz_EMR4.esc 70 8.1.1
monitoring and control is available. Tier4Interim
support.
Deutz engines TCD 9.0 and other Deutz engines
Deutz_EMR5.esc 194 8.1.1 with ECU EMR 5 / MD1. Stage V monitoring and
control is supported.
Doosan G2 stage V engines (D18, D24, and D34)
Doosan_G2_EDC17.esc 193 8.1.1
equipped with Bosch EDC17C87.
The ECU CPC4 is for Daimler engine OM47x series
Daimler_CPC4.esc 209 8.1.1
(MTU 6R1x00 series)
Cummins ISDe, ISLe, ISZ series with Dongfeng
Dongfeng_Cummins.esc 218 8.1.1
control unit.
For Doosan Infracore’s DX22 electronically
Doosan_MD1.esc 206 8.1.1 controlled diesel engine for generators equipped
with Bosch MD1CE ECU.
Deep Sea Electronics Digital Automatic Voltage
DSE_DSEA109.esc 268 8.1.1
Regulator (AVR) with CAN Communications & PMG.
For up to 12 cylinder diesel engines (MAN E3262)
Econtrols_EICS.esc 291 8.1.1
equipped with EControls engine control unit
FORD natural gas or propane or gasoline engines
Ford_e-control.esc 95 8.1.1
2.3L, 5.7L or others with e-control module.
FroniusSymo.esc 1026 8.1.1 Fronius Symo. SunSpec reading int+SF.
GM natural gas or propane engines GM3.0, GM4.3,
GM_e-control.esc 44 8.1.1
GM5.0, GM5.7 or others with e-control module.
GM natural gas or propane engines GM4.3, GM5.7
GM_e-control_LCI.esc 58 8.1.1
or others with e-control LCI engine control unit.
GM diesel engines with MEFI4B or MEFI5B engine
GM_MEFI4/MEFI5B.esc 34 8.1.1
control unit.
GM diesel engines with MEFI6 engine control
GM_MEFI6.esc 71 8.1.1
unit.Tier 4 monitoring and control is available.
GM diesel engines with Woodward SECM interface.
GM_SECM.esc 35 8.1.1
SECM with address 1 is only supported !
Gas engine with Woodward LECM E6 Engine
Guascor_LECM_E6.esc 147 8.1.1 control unit. Applicable for Guascor engines SFGLD
480, SFGLD 560, HGM 560. Under tests!
Hatz diesel engines series H50 (4H50TIC) equipped
Hatz_EDC.esc 165 8.1.1
by EDC17engine control unit.
Heinzmann ARIADNE KC-01 knock monitoring
Heinzmann_Ariadne.esc 274 8.1.1 system. Supported communication is J1939
standard over CAN.
Heinzmann GMA gas mixer series, communication
Heinzmann_GMF.esc 172 8.1.1
over CAN.

ECU list 8.1.1 New Features List 69

 Heinzmann HELENOS DC 2 digital speed governor
Heinzmann_Helenos.esc 273 8.1.1 system. Supported communication is J1939
standard over CAN.
Heinzmann KRONOS 20 electronically controlled
Heinzmann_Kronos.esc 275 8.1.1 mixture control system. Supported communication is
J1939 standard over CAN.
Heinzmann PANDAROS DC 6 digital speed
Heinzmann_Pandaros.esc 105 8.1.1 governor system. Supported communication is
J1939 standard over CAN.
Heinzmann PHLOX II high-energy capacity spark
ignition control system, up to 24 cylinders.
Heinzmann_Phlox.esc 83 8.1.1
Supported communication is J1939 standard over
CAN.
Inductive ignition system for up to 8 coils by single
HuegliTech_LEF200.esc 292 8.1.1
unit and up to 16 cylinders in total.
HT-SG-50 electronic speed governor for
HuegliTech_SG50&SG100.esc 267 8.1.1 conventional diesel engines, HT-SG-100 for gas
engines. Communication over CAN J1939.
Iveco NEF N40, N60 series or Cursor 9, 10, 13
Iveco_MD1.esc 187 8.1.1 series engines with Bosch MD1 engine control unit.
Stage V support.
Iveco F5 series variable speed engines with Bosch
Iveco_MD1_IPU.esc 269 8.1.1
MD1 engine control unit. Stage V support.
Isuzu engine 4HK, 4J, 6HK, 6U, 6W series or others
with ECM engine control unit. Tier 4 monitoring and
Isuzu_ECM.esc 36 8.1.1
control is available. Tier4Final support (check
particular firmware for support details).
Iveco NEF N40, N60 series or Cursor 9, 10, 13
Iveco_NEF_&_Cursor.esc 14 8.1.1 series engines with Bosch EDC engine control unit.
Tier4Interim support.
Iveco Vector engines with ADEM engine control unit.
Iveco_Vector.esc 28 8.1.1
Tier 4 monitoring and control is available.
Jenbacher gas engines with Diane control system.
Jenbacher_Diane.esc 22 8.1.1
Communication interface RS485 !
JCB Dieselmax or ecoMAX engines with Delphi
JCB_Delphi_DCM.esc 23 8.1.1
DCM engine control unit.
Jichai diesel engines JC15D equipped with EU3A-
Jichai_EU3A.esc 227 8.1.1
00AT engine control unit.
John Deere diesel engines with JDEC engine control
John_Deere.esc 7 8.1.1 unit. Tier 4 monitoring and control is available.
Tier4Final support.
Kohler.esc 178 8.1.1 Kohler diesel engines series KDI 1903 - 2504 TCR
Kubota diesel engine equipped with a control unit.
Kubota.esc 122 8.1.1
Tier4Interim support.
Kubota E4 and E5 type (V2403 CR) diesel engines
Kubota_EDC17.esc 224 8.1.1 equipped with Bosch EDC17 electronic control unit.
Stage V support.
Inductive ignition system for up to 8 coils by single
LEF200.esc 292 8.1.1
unit and up to 16 cylinders in total
Leroy Somer D500 series digital AVR
Leroy_Somer_AVR_CD500.esc 191 8.1.1 communication over SAE J1939. For proper
sunctionality check for controller's FW compatilibity!
Liebherr_LIDEC1.esc 135 8.1.1 Liebherr Dxxx diesel engines equipped by LIDEC1

ECU list 8.1.1 New Features List 70

 engine control unit. Under tests!
Liebherr Dxxx diesel engines equipped by LIDEC2
Liebherr_LIDEC2.esc 215 8.1.1
engine control unit.
Mahindra diesel engines MHEL 7.2L equipped by
Mahindra.esc 180 8.1.1 engine control unit - Sparrow G+ A34C or A34B.
Under tests!
MAN diesel engines equipped by EDC17 engine
MAN_EDC_17.esc 174 8.1.1
control unit.
For reading data from ID-Mobile Logger. This ECU is
MAN_data_logger.esc 56 8.1.1
not supported by InteliDrive Nano controller!
MAN diesel engines 6R, 8V, 12V or others with MFR
MAN_MFR.esc 29 8.1.1
interface and EDC engine control unit.
Marathon digital automatic voltage regulator
Marathon_DVR2000EC.esc 272 8.1.1
DVR2000EC+
ModbusUserDevice.esc 1024 8.1.1 Modbus User Device.
Motortech Ignition controller covering various
Motortech_MIC_850.esc 256 8.1.1
Motortech products, e.g. MIC850 and others.
MTU engines series 2000/4000 with ADEC (ECU7)
MTU_ADEC_J1939.esc 20 8.1.1 control unit. SAM interface module with CCB2 card
is required !
MTU P - engines series 2000/4000 with ADEC
MTU_ADEC_J1939_P-engines.esc 37 8.1.1 (ECU7) control unit and EMU module. SAM interface
module with CCB2 card is required !
MTU 4R1000, 6R1000, 6R1100, 6R1300, 6R1500 or
Detroit DD13, DD15, DD16 or Fuso 6R10 diesel
MTU_DDEC10.esc 117 8.1.1
engines equipped with DDEC10 engine control unit.
Tier4Final support. Under tests!
MTU engines series 4000 with ADEC (ECU7) control
MTU_ECU7.esc 130 8.1.1
unit. SAM interface module is not required!
MTU engines fitted with ECU 9 control unit.
MTU_ECU 9.esc 125 8.1.1 Supported diesel engines with FSW ver.2.0, gas with
FSW ver.2.3. Tier4Interim support. Under tests!
Central connection box of MTU marine engine series
MTU_EIM.esc 120 8.1.1
2000/4000. Commonly used with MTU ECU7.
MTU MIP 4000 genset controller. It is necessary to
use an UL-7112-Plus converter with appropriate
MTU_MIP4000.esc 166 8.1.1
configuration as a bridge between the controller and
the MIP4000 panel. Under tests!
MTU MIP 4000 genset controller. It is necessary to
use an IFG converter with appropriate configuration
MTU_MIP4000_J1939.esc 212 8.1.1
as a bridge between the controller and the MIP4000
controller.
MTU engines series 1600 with ADEC (ECU8) control
MTU_SMART_Connect.esc 60 8.1.1
unit. SMART connect interface module is required !
Reading of parameter ONLY from MWM engines
MWM_Adem.esc 201 8.1.1 TCG 3016 V12 or V16, equipped with CAT ADEM
A4 ECU.
MWM gensets with MWM 229-3, 4.12, 6.12, Scania
MWM_SECM.esc 287 8.1.1 OC13-G and MAN V12 engines with Woodward
SECM70 electronic control unit.
Perkins Engine 904J with ADEM A6E11 ECU. Stage
Perkins_ADEM_A6E11.esc 265 8.1.1
V monitoring and support are supported.
Perkins_1300.esc 54 8.1.1 Perkins series 1300 engines. No engine control by

ECU list 8.1.1 New Features List 71

 the controller is available.
Perkins series 1100, 1300, 2300, 2500 and 2800
Perkins_ECM.esc 12 8.1.1
engines.
Powerlink.esc 198 8.1.1 Powerlink ECU, Communication over CAN.
Scania singlespeed series DC9, DI12, DC12, DC16,
D9M, DI12M, DI16M engines or others with S6
Scania_S6_Singlespeed.esc 16 8.1.1
engine control unit (software version 1794335 or
higher).
Scania allspeed series DC9, DI12, DC12, DC16,
D9M, DI12M, DI16M engines or others with S6
Scania_S6_Allspeed.esc 11 8.1.1
engine control unit (software version 1794335 or
higher).
Scania allspeed series DC9, DC13,DC16 engines
Scania_S8_Allspeed.esc 69 8.1.1
with S8 engine control unit. Tier4Final support.
Scania singlespeed series DC9, DC13,DC16
Scania_S8_Singlespeed.esc 68 8.1.1 engines with S8 engine control unit. Tier4Final
support.
Siemens diesel engines SGE-42HM equipped by
Siemens_GCS_E.esc 284 8.1.1
GCS-E control unit.
HT-SG-50 electronic speed governor for
SG50&SG100.esc 267 8.1.1 conventional diesel engines, HT-SG-100 for gas
engines. Communication over CAN J1939.
Adelsystem CB12245AJ supports Smart Battery
Sinotruk_BBM.esc 223 8.1.1
Charger via CAN bus communication.
SISU gen-set engines with EEM3 engine control
SISU_EEM3_Gen-set.esc 18 8.1.1
unit.
SISU propulsion engines with EEM3 engine control
SISU_EEM3_Propulsion.esc 19 8.1.1
unit.
This contains only values defined by CAN SAE
Standard_J1939_engine.esc 255 8.1.1
J1939 specification. Tier4Final support.
This configuration contains only received values by
the controller. There is not a support of transmitted
Standard_J1939_monitor.esc 118 8.1.1 values from the controller. Use this configuration if
any 3rd party module is dedicated to control the
engine. Tier4Final support.
Steyr_EDC17.esc 185 8.1.1 Steyr and Volvo engines with Bosch EDC17 ECU
Steyr marine or industrial engines with M1 engine
Steyr_M1.esc 66 8.1.1 control unit. No engine control by the controller is
available.
CAT CG132B-08 / 12 / 16 or MWM TCG30XX with
TPEM.esc 217 8.1.1 TPEM v1.6 panel. Communication via Modbus RTU
ECU-LINK.
Varistep1.esc 257 8.1.1 Motortech Varistep unit.
Varistep2.esc 258 8.1.1 Motortech Varistep unit.
VM_Industrial.esc 32 8.1.1 VM industrial engines with EDC engine control unit.
VM_Marine.esc 31 8.1.1 VM marine engines with EDC engine control unit.
VolvoPenta propulsion series D4, D6 engines with
Volvo_EDC7_Allspeed_KWP2000.esc 114 8.1.1 EDC7 engine control unit. This ECU is not supported
by InteliDrive Nano controller!
VolvoPenta singlespeed series D9, D12, D13, D16
Volvo_Singlespeed.esc 1 8.1.1 engines with EMSI / EMSII / EMS2.2 engine control
unit.

ECU list 8.1.1 New Features List 72

 VolvoPenta propulsion series D5, D7, D9, D12, D13,
Volvo_Allspeed.esc 2 8.1.1
D16 engines with EDC or EMS engine control unit.
Volvo_EMS_J1587.esc 163 8.1.1 Volvo Pentq J1587 support.
VolvoPenta Industrial series D9, D12, D13, D16
Volvo_Industrial_EMS2.4.esc 264 8.1.1 engines with EMS 2.4 engine control unit. Stage V
support available
Waukesha Engenius Engine System Manager with
Waukesha_ESM.esc 15 8.1.1
Modbus interface. Communication interface RS485 !
Waukesha Engenius Engine System Manager 2 with
WaukeshaESM2.esc 203 8.1.1
Modbus interface. Communication interface RS485!
Waukesha Engenius Engine System Manager 2 with
WaukeshaESM2_ModbusMaster.esc 1027 8.1.1
Modbus interface. Communication interface RS485!
Baudouin diesel engines 12M26, 12M33 and 16M55
equipped by Wise 10B ECU engine control unit.
Weichai_Wise_10B.esc 196 8.1.1
Currently supported only by ID-DCU Marine
controller. Under tests!
Weichai_Wise_12B.esc 195 8.1.1 Weichai engines with Wise12B control unit.
Weichai_WISE13A.esc 200 8.1.1 Weichai engines P2.3N and P4.1.
Weichai diesel engines equipped by EDC7 or
Weichai_Wise_15A.esc 170 8.1.1
EDC17 engine control unit. Under tests!
Baudouin diesel engines 16M55 equipped by two
Weichai_Wise18B_Duel.esc 294 8.1.1 Wise 18B ECU engine control units in master slave
configuration.
WW_IC920.esc 293 8.1.1 Capacitive discharge ignition for up to 20 coils.
YaMZ diesel engines series 530 (534, 536),
YaMZ_EDC7.esc 175 8.1.1
equipped by EDC7 engine control unit.
For Yanmar Industrial engines 3TNV88, 3TNV86,
Yanmar_EDC17.esc 213 8.1.1 3TNV98 series equipped with Bosch EDC17CV54.
Tier 4 Final supported.
Yanmar_TNV.esc 89 8.1.1 Yanmar engine 3TNVA with TNV control unit.
Yuchai engines series YC6K, YC6MK, YC6L, YC6G,
Yuchai_YC-BCR.esc 159 8.1.1 YC6A, YC6B with YC-BCR engine control unit.
Under tests!
Yuchai engines series YC12VC, YC6C with ECU2
Yuchai_YC-LBR.esc 168 8.1.1
engine control unit. Under tests!
Yuchai engines series YC6T, YC6TD, YC6C,
Yuchai_YCECU.esc 156 8.1.1 YC12VC, YC16VC with YCECU engine control unit.
Under tests!

ECU list 8.1.1 New Features List 73

29.3 Document history
Related sw.
Revision number Date Author
version
21 8.1.1 24.2.2023 Jakub Vávra
20 8.1.0 31.1.2023 Jakub Vávra
19 8.0.0 29.9.2022 Jakub Vávra
18 7.9.0 8.6.2022 Jakub Vávra
17 7.8.1 15.3.2022 Jakub Vávra
16 7.8.0 31.1.2022 Jakub Vávra
15 7.7.0 4.10.2021 Jakub Vávra
14 7.6.0 2.6.2021 Jakub Vávra
13 7.5.0 24.2.2021 Jakub Vávra
12 7.4.0 18.11.2020 Jakub Vávra
11 7.3.1 4.8.2020 Jakub Vávra
10 7.3.0 30.6.2020 Jakub Vávra
9 7.2.1 29.2.2020 Roman Taragel
8 7.2.0 26.2.2020 Roman Taragel
7 7.1.0 30.10.2019 Roman Taragel
6 7.0.0 19.6.2019 Roman Taragel
5 6.9.0 5.11.2018 Roman Taragel
4 6.8.0 10.1.2018 Roman Taragel
3 6.7.0 31.8.2017 Roman Taragel
2 6.6.0 21.6.2017 Jan Horacek
1 6.5.0 15.3.2016 Roman Taragel

ECU list 8.1.1 New Features List 74