Messier-Dowty SA

CAGE: F0189
BP 10 - 78142 Vélizy Cedex - France
Tel: +33 (0) 1 46 29 18 00 - Fax: +33 (0) 1 46 29 87 70
Telex: 634156F - Sita: QBHMDCR

ELECTRICAL LOOM

PARTS NUMBERS

D22367000 , D22368000
D22367000-1 , D22368000-1
D22367000-2 , D22368000-2

COMPONENT MAINTENANCE MANUAL

WITH
ILLUSTRATED PARTS LIST

STATEMENT OF INITIAL CERTIFICATION

The technical content of this document has been accepted under the authority of Technical Publications
Manager of Messier Dowty SA.
NOTE: The front page will always keep this initial certification. But this certification does not apply to revisions of the CMM.
Revisions are certified and recorded on the ‘Record of Revisions’ page.

© Messier-Dowty 2005
This document and all information contained herein is the sole property of Messier-Dowty. No intellectual property rights are
granted by the delivery of this document or the disclosure of its content. This document shall not be reproduced to a third party
without the express written consent of Messier Dowty.
Title Page
Page 1
Initial Issue: MAY 14/82 32-09-17 Jan 15/11
PAGE INTENTIONALLY LEFT BLANK
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

LETTER OF TRANSMITTAL FOR REVISION No 6

1. Permanent revisions

A. Check that Revision No 5 has been recorded as having been inserted in the manual.

2. New/revised pages
REMOVE/INSERT
SUBJECT
NEW/REVISED REASON OF CHANGE
REFERENCE
PAGES

Title Page 1 Logo updated.

Date updated.
Record of Revisions 1 Logo updated.
Revision no 6 added.
List of Effective
Pages 1 and 2 Logo updated.
Indication of new chapter and/or chapter deleted.
3. Revision record

A. Record the issue date and insertion date of this revision in the Record of Revisions and
retain this Letter of Transmittal.

LETTER OF TRANSMITTAL FOR REVISION No 6

Page 1
32-09-17 Jan 15/11
PAGE INTENTIONALLY LEFT BLANK
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

RECORD OF REVISIONS
Keep this record in front of the manual. When you get a revision, put the revision pages into the
manual. Write the revision number and date, the date at which the revision is put into the manual
and your initials.
REV REVISION DATE REV REVISION DATE
BY BY
No DATE INSERTED No DATE INSERTED

1 SEP 30/85
2 AUG 29/86
3 JUN 28/91
4 Apr 15/98
5 Apr 30/07
6 Jan 15/11

RECORD OF REVISIONS
Page 1
32-09-17 Jan 15/11
PAGE INTENTIONALLY LEFT BLANK
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

RECORD OF TEMPORARY REVISIONS

Keep this record in front of the manual. When you get a temporary revision, put the yellow revision
pages into the manual opposite the pages to be changed. Write the revision number, the date at
which the revision is put into the manual and your initials. Do not remove the yellow pages until a
permanent revision which contains this information is released.
TEMPORARY
PAGE DATE DATE
REVISION BY BY
NUMBER INSERTED REMOVED
NUMBER
PRINTED IN FRANCE

RECORD OF TEMPORARY REVISIONS

Page 1
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

RECORD OF SERVICE BULLETINS

NOTE: The Service Letters (SL) are usually released to give general information. But some
Service Letters can contain more data on procedures or modifications which were given to
the equipment user. These Service Letters are thus shown in the SERVICE LETTER
Column.
SERVICE SERVICE DATE OF
REV
BULLETIN LETTER INCORPORATION DESCRIPTION
NUMBER
NUMBER NUMBER INTO MANUAL

470-32-777 Apr 15/98 Installing heat shrinkable

sleeves on the connectors of
the electrical looms
(FAM 805)

D22367000 is changed into

D22367000-1.
D22368000 is changed into
D22368000-1.

470-32-807 Apr 30/07 Modification of the electrical

harness definition.
(FAM 837)

D22367000-1 is changed into

D22367000-2.
D22368000-1 is changed into
D22368000-2.

470-32-810 Apr 30/07 Removal of selfsoldering sleeves.

Addition of CAF 4 "Rhodorsil"
under heat shrinkable sleeves.
(FAM 841)

D22367000-2 is changed into

PRINTED IN FRANCE

D22367000-2 Amdt. A.
D22368000-2 is changed into
D22368000-2 Amdt. A.

RECORD OF SERVICE BULLETINS

Page 1
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

LIST OF EFFECTIVE PAGES

SUBJECT PAGE DATE SUBJECT PAGE DATE

Title Page 1 Jan 15/11 Cleaning 401 Apr 30/07
2 BLANK 402 BLANK

Record of 1 Jan 15/11 Check 501 Apr 30/07

Revisions 2 BLANK 502 BLANK

Record of 1 MAY 14/82 Repair 601 Apr 30/07

Temporary 2 BLANK 602 JUN 28/91
Revisions 603 JUN 28/91
604 JUN 28/91
Record of 1 Apr 30/07 605 JUN 28/91
Service 2 BLANK 606 JUN 28/91
Bulletins 607 Apr 30/07
608 Apr 30/07
List of 1 Jan 15/11 609 JUN 28/91
Effective Pages 2 Jan 15/11 610 Apr 30/07
611 MAY 14/82
Table of 1 Apr 30/07 612 BLANK
Contents 2 Apr 30/07 613/614 JUN 28/91
615 AUG 29/86
List of Special 1 Apr 30/07 616 AUG 29/86
Materials 2 Apr 15/98
3 Apr 30/07 Assembly and 701 MAY 14/82
4 Apr 30/07 Storage 702 AUG 29/86
703 MAY 14/82
Introduction 1 Apr 15/98 704 BLANK
2 Apr 30/07
Fits and 801 MAY 14/82
Description and 1 MAY 14/82 Clearances - 802 BLANK
Operation 2 MAY 14/82 Torque Values
3 AUG 29/86
4 AUG 29/86 Special Tools, 901 Apr 30/07
5 AUG 29/86 Fixtures and 902 DELETED
6 BLANK Equipment

Testing and 101 Apr 30/07 TP 1001 1 MAY 14/82

Fault 102 Apr 30/07 2 BLANK
Isolation

Disassembly 301 MAY 14/82

302 BLANK

Revision No 6 LIST OF EFFECTIVE PAGES

Page 1
32-09-17 Jan 15/11
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

SUBJECT PAGE DATE

INTRO 1001 1 Apr 30/07
2 Apr 30/07
3 Apr 30/07
4 Apr 30/07
5 Apr 30/07
6 Apr 30/07
7 DELETED

NUMERICAL 1 Apr 30/07

INDEX 2 Apr 30/07
3 Apr 30/07
4 Apr 30/07
5 Apr 30/07
6 Apr 30/07
7 Apr 30/07
8 BLANK

Illustrated 1001-00 Apr 30/07

Parts List 1001-01 Apr 30/07
1001-02 Apr 30/07
1001-03 Apr 30/07
1001-04 Apr 30/07
1001-05 Apr 30/07
1001-06 Apr 30/07

1002-00 Apr 30/07

1002-01 Apr 30/07
1002-02 Apr 30/07
1002-03 Apr 30/07
1002-04 Apr 30/07

Revision No 6 LIST OF EFFECTIVE PAGES

Page 2
32-09-17 Jan 15/11
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

TABLE OF CONTENTS
SUBJECT OR PARAGRAPH TITLE Page

DESCRIPTION AND OPERATION 1

1. General 1
2. Characteristics 1
3. Description and Operation 1
TESTING AND FAULT ISOLATION 101
1. General 101
2. Tools and test equipment 101
3. General test conditions 101
4. Testing 102
A. Insulation testing 102
B. Electrical continuity and voltage drop test 102
DISASSEMBLY NOT APPLICABLE
CLEANING 401
1. Cleaning of parts 401
CHECK 501
1. Visual inspection 501
A. Male connectors 501
B. Connector bases 501
C. Coupling units -coupling assemblies - end fittings 501
D. Sheath assemblies 501
E. Cables 501
REPAIR 601
1. Replacement of components 601
A. Removal 601
B. Re-installation 604
2. Protective treatment 610
A. External protective treatment 610
B. Internal protective treatment 610
PRINTED IN FRANCE

TABLE OF CONTENTS
Page 1
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

SUBJECT OR PARAGRAPH TITLE Page

ASSEMBLY AND STORAGE 701
1. Assembly not applicable
2. Storage after assembly 701
A. Purpose 701
B. General 701
C. Preservation and packaging 701
D. Removal from store and subsequent testing 703
FITS AND CLEARANCES - TORQUE VALUES NOT APPLICABLE
SPECIAL TOOLS, FIXTURES AND EQUIPMENT 901
1. Test equipment 901
2. Special tools and equipment 901
ILLUSTRATED PARTS LIST (IPL) 1001
PRINTED IN FRANCE

TABLE OF CONTENTS
Page 2
N 32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

LIST OF SPECIAL MATERIALS

NOTE: You can use equivalent materials.
WHERE
USED
A
R
C C S
PRODUCT NAME VENDOR'S TRADE NAME VENDOR'S ADDRESS T
L H
E
S
E P
E E E
S A
A C M.
T I
N K S
R
T

Cleaning product DUPONT DE 5001, MAYFIELD ROAD X

for electronic NEMOURS CLEVELAND OH44124
components U.S.A.
FLUGENE 113MA
or
Cleaning product APPROVED VENDOR
for electronic
components
MIL-C-81302

Wooden case MESSIER-BUGATTI BP 40 X

or cardboard 78141 VELIZY CEDEX
box FRANCE

Desiccant D.Y.D.R.A. 12, rue du PORT X

AIR 8060 DE LA CELLE
(MIL-D-3464) 77670 ST MAMMES
FRANCE

METHANOL MERCK EUROLAB 201, Rue Carnot X

AIR 3651 94120 FONTENAY S/BOIS
(O-M-232 GRADE A) FRANCE
DELETED
PRINTED IN FRANCE

LIST OF SPECIAL MATERIALS

Page 1
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

WHERE
USED
A
R
C C S
PRODUCT NAME VENDOR'S TRADE NAME VENDOR'S ADDRESS T
L H
E
S
E P
E E E
S A
A C M.
T I
N K S
R
T

Greaseproof S.E.E.T. 117, rue de ROME X

paper 75017 PARIS
AIR 8140 FRANCE
CATEGORY 1122
(MIL-B-121B
GRADE A
CLASS 1
TYPE 2)

Heat- S.E.E.T. 117, rue de ROME X

sealable 75017 PARIS
cloth FRANCE
AIR 8140
CAT. 1121
(MIL-B-131
CLASS 1)

Anti-corrosion S.P.C.A. 9, Voie de Seine X

product 94290 VILLENEUVE LE ROI
AIR 8136 FRANCE
(PROTEX G6)
(MIL-C-11796
CLASS 3)

Greaseproof INDUTEX 51, Promenade X

cloth AIR 8140 des Ponts
PRINTED IN FRANCE

CATEGORY 22 92300 LEVALLOIS-PERRET

(MIL-B-121C) FRANCE

LIST OF SPECIAL MATERIALS

Page 2
32-09-17 Apr 15/98
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

WHERE
USED
A
R
C C S
PRODUCT NAME VENDOR'S TRADE NAME VENDOR'S ADDRESS T
L H
E
S
E P
E E E
S A
A C M.
T I
N K S
R
T

Cellophane LEROYER BP 663 X

shavings 95004 CERGY PONTOISE
FRANCE

Micro-crystalline wax COMMERCIALLY X

(JAN-P-115) AVAILABLE

KRAFT Paper CIE GENERALE 42, rue des 7 ARPENTS X

NFQ 12007 DES PAPIERS 93500 PANTIN
FRANCE

Cleaning COMMERCIALLY X X
product AVAILABLE
WHITE SPIRIT
or
Cleaning COMMERCIALLY
product AVAILABLE
PD 680

Polyethylene PLASTIQUES DU LE PEYCHIER X

0,22 mm VELAY 43600 STE SIGOLENE
(0.008 in) FRANCE
thick

Protective product C.F.P.I. 28, Bd CAMELINAT X

ALODINE 1200 92233 GENNEVILLIERS
PRINTED IN FRANCE

or FRANCE
Protective product APPROVED VENDOR
(MIL-C-5541
Class 1A)

LIST OF SPECIAL MATERIALS

Page 3
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

WHERE
USED
A
R
C C S
PRODUCT NAME VENDOR'S TRADE NAME VENDOR'S ADDRESS T
L H
E
S
E P
E E E
S A
A C M.
T I
N K S
R
T

Colourless varnish AKZO COATINGS 164, rue Ambroise CROIZAT X

Aerodur 93204 SAINT DENIS
clearcoat UVR FRANCE
+ Hardener S66/22R
or
Polyurethane based APPROVED VENDOR
colourless varnish
made of two
constituents
and of the same
chemical
composition as that of
varnish to
spec.BMS 1060
Type 1

Cement RHODIA 19 Ave Georges Pompidou X

RHODORSIL Groupe AVENTIS 69003 LYON
CAF4 FRANCE
PRINTED IN FRANCE

LIST OF SPECIAL MATERIALS

Page 4
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

INTRODUCTION
1. General - Layout

A. This manual which includes the ILLUSTRATED PARTS LIST, is made to ATA
Specification No 100.

B. This manual gives the function of the component and all the instructions for its repair in a
specialized workshop to put it in a serviceable condition.

C. The procedures included in this manual are given for your guidance but you can use
equivalents (or better procedures) if the facilities of the repair shop permit.

D. This manual does not include instructions on the standard techniques, the widely used
suppliers' materials and calendar limits of any type (frequencies, life, storage, etc.)
applicable to the component.

E. The procedures used for surface treatments, protections, inspections, etc. are given in
the special manual 32-09-01 entitled "STANDARD REPAIR PRACTICES".

F. The instructions contained in this manual can not include all the details of the
components because they are based on a normal performance in operation of the unit
and of its components which can be damaged with the time.

G. Use at all times, in the repair shop, safety precautions to prevent injury to persons and
damage to the component.

H. The manual has been verified by simulation and will be revised as necessary to give
current information.

I. The values are given in units of the International System (S.I. units) with the U.S.
standard units in parentheses after the S.I. units.
The conversions and abbreviations used are listed, for reference, in the table below:
PRINTED IN FRANCE

INTRODUCTION
Page 1
32-09-17 Apr 15/98
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

S.I. UNITS Abbreviations U.S. STANDARD UNITS Abbreviations

Degree Celsius
°C Degree Fahrenheit °F
(or centigrade)
Millimeter mm Inch in
Pound force per foot
Newton-meter N.m lbf.ft or lbf.in
or Pound force per inch
Newton N Pound force lbf
Kilogram kg Pound (mass) lb
Gram g Ounce oz
Mega Pascal MPa Kilo pound square inch k.s.i.
Bar bar Pound square inch p.s.i.
Square centimeter cm2 Square inch in2
Cubic centimeter cm3 Cubic inch in3
Liter l Gallon US Gal
Volt V Volt Direct Current VDC
MilliVolt mV Root Mean Square RMS

2. General - Change in instructions

You must inform Messier-Dowty SA of any problem not shown in this manual, to find a solution
that you will use in the shortest possible time.
If the solution found can come into general and repetitive use, a subsequent revision to the
manual will be made to introduce this solution.

3. Index of publications
This MANUAL and its subsequent changes are given in the INDEX OF Messier-Dowty SA
COMPONENT MAINTENANCE MANUALS No 20180.
PRINTED IN FRANCE

INTRODUCTION
Page 2
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

DESCRIPTION AND OPERATION

1. General
The (RH and LH) front dual-wheel upper looms are part of the electrical equipment of a main
landing gear leg.

2. Characteristics
Total weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,10 kg (6.8336 lb)
Nominal operating voltage . . . . . . . . . . . . . . . . 28 V d.c.
Operating temperature. . . . . . . . . . . . . . . . . . . ) Min: -40°C (-40°F)
) Max: +70°C (+158°F)
Operating temperature ) Min: -50°C (-55°F)
range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ) Max: +80°C (+176°F)
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . as per NAS1599.

3. Description and Operation

(see Figure 1 and Figure 2)
The electrical looms are handed for LH and RH installation. Identification numbers assigned to
RH and LH connectors and looms permit to distinguish them.
The looms are attached along the upper part of a main landing gear leg. Each loom connector
is identified by a tie which is set on the corresponding sheath, when the connectors are fitted
to the free ends of the sheaths, and to the base in the case of a socket.
The front dual-wheel upper loom includes two coupling units to which are attached a socket,
three sheath assemblies and one intermediate sheath which connects the two coupling units.
PRINTED IN FRANCE

Page 1
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM
PRINTED IN FRANCE

GENERAL VIEW

Page 2
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM
PRINTED IN FRANCE

Wiring diagram
LH front dual-wheel electrical loom
Figure 1

Page 3
32-09-17 AUG 29/86
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM
PRINTED IN FRANCE

Wiring diagram
RH front dual-wheel electrical loom
Figure 2

Page 4
32-09-17 AUG 29/86
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

The routing of the cables fitted with plugs that are mated to the corresponding connectors is
supplied by the coupling unit and sheaths.
The upper disconnecting sheath is fitted to the upper coupling unit and the socket, which
permits connection with the lower loom, is fitted to the lower coupling unit.
LH loom RH loom
1923 VCA 1924 VCA Upper disconnecting plug
75GGA 76GGA To emergency servo-valve
62GBA 63GBA To proximity switch
(shock absorber)
1925VC 1926VC To lower loom
(lower disconnecting plug).
PRINTED IN FRANCE

Page 5
32-09-17 AUG 29/86
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

TESTING AND FAULT ISOLATION

NOTE: Equivalent alternatives may be used for listed items.

1. General
Two aspects are to be considered:
– Functional testing of the unit following faults found in service or during troubleshooting.
– Complete testing of the unit after repair.
NOTE: The detail parts of the unit are shown on Figure 1 and Figure 2 of the Illustrated Parts
List.

2. Tools and test equipment

– Electrical test panel type SK30488-1000 with interface D21972-XXX.
– Multimeter Accuracy: + 1 % DC.
Range: 0 to 1 volt.
– Stabilised power supply Capable of operating with a current adjustable from 0.1 to 1 Amp
at a potential difference less than 1 volt.
– Megohmmeter Insulation resistance measurement: 20 megohms under
45 V DC.
NOTE: If the operator does not possess the electrical test panel recommended by the
manufacturer, he should use, for this particular unit, the test equipment whose
characteristics are defined in the 900 series pages.
3. General test conditions
The tests are to be carried out in the following conditions:
– ambient temperature between 10°C (50°F) and 30°C (86°F).
– ambient atmospheric pressure.
– relative humidity approximately 70 %.
PRINTED IN FRANCE

Page 101
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

4. Testing
A. Insulation testing

(1) Using the electrical test panel or the megohmmeter, apply 45 V DC in succession
between:

(a) all the wires of connector 1923VCA or 1924VCA joined together and the
mechanical earth,

(b) Each single wire of connector 1923VCA or 1924VCA and all the others joined
together (to be repeated as many times as there are wires).

(2) Make sure that the resistance is greater than 20 megohms.

B. Electrical continuity and voltage drop test

CAUTION: THIS TEST IS TO BE CARRIED OUT WITH AN APPLIED CURRENT OF
1 A.
NOTE: If the standard test equipment is being used, this test is to be carried out using
the KELVIN method ("four-lead" arrangement), with 1 A applied
In both cases, the test procedure for each connector is described below.

(1) Connectors 1923VCA and 75GGA or 1924VCA and 76GGA

– Examine the electrical continuity between terminals P and F, R and E, S and C, T
and A, and make sure that the voltage drop is between 50 mV and 95 mV.

(2) Connectors 1923VCA and 63GBA or 1924VCA and 62GBA

– Examine the electrical continuity between terminals L and C, N and A, M and B,
and make sure that the voltage drop is between 230 mV and 435 mV.

(3) Connectors 1923VCA and 1925VC or 1924VCA and 1926VC

– Examine the electrical continuity between terminals Y and Y, Z and Z, a and a,
b and b, c and c, d and S and make sure that the voltage drop is between 90 mV
and 125 mV.
– Examine the electrical continuity between terminals U and U, A and A, V and V,
B and B, W and W, C and C, X and X, D and D, e and T, E and E, f and P,
PRINTED IN FRANCE

g and N, j and M, F and L, H and F, J and G, K and H and make sure that the
voltage drop is between 215 mV and 405 mV.
– Examine the electrical continuity between terminals G and K, h and J (continuity
of the screening).

Page 102
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

DISASSEMBLY NOT APPLICABLE

PRINTED IN FRANCE

Page 301
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

CLEANING
NOTE 1: Equivalent alternatives may be used for listed items.
NOTE 2: The detail parts of the unit are shown on Figure 1 and Figure 2 of the Illustrated Parts
List.
NOTE 3: The suppliers of recommended products and materials are listed in the preliminary
pages of this manual.

1. Cleaning of parts
Clean all parts of the electrical loom with FLUGENE 113 MA, then dry them with dry
compressed air.
PRINTED IN FRANCE

Page 401
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

CHECK
NOTE 1: Equivalent alternatives may be used for listed items.
NOTE 2: The detail parts of the unit are shown on Figure 1 and Figure 2 of the Illustrated Parts
List.
NOTE 3: This Section deals with the checks required to ascertain the serviceability of the
electrical loom. The replacement of defective parts of the loom is described in the
Section "REPAIR".

1. Visual inspection

A. Male connectors
Examine the condition of the insulation and the locking clips, and make sure that the
contacts show no signs of erosion or burning.

B. Connector bases
Make sure that the connector, base and nut are free from cracks, and that the contacts
show no signs of erosion or burning.

C. Coupling units -coupling assemblies - end fittings

Make sure that there is no distortion, cracking or alteration to the internal layer of blue
epoxy resin.

D. Sheath assemblies
Examine the condition of the metal braids (no fraying), the attachment clips, the eyelets
and the protective and cable marking sleeves.

E. Cables
Examine the continuity of the wires.
PRINTED IN FRANCE

Page 501
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

REPAIR
NOTE 1: The detail parts of the unit are shown on the figures of the Illustrated Parts List (I.P.L.).
NOTE 2: There is a list of the suppliers of recommended mixtures and materials in the first pages
of this MANUAL.
NOTE 3: Equivalent alternatives may be used for listed items.

1. Replacement of components
The removal and re-installation of defective parts is dealt with a progressive disassembly and
reassembly sequence for the replacement of:
– coupling unit assemblies,
– connectors (male or bases),
– contacts,
– twisted cables, two-lead twisted shielded cables and dummy cables,
– sheath assemblies.
NOTE 1: For heat-shrinkable sleeves, the shrinking temperature will be approximately 200°C
(329°F).
NOTE 2: After disassembly, the sheath attachment clips will be replaced by "repair" clips
(Second mounting clips).

A. Removal
(1) Removal of a routing and coupling assembly (see Figure 601)

(a) Remove the cover from the coupling unit assembly by opening the attachment
springs.

(b) Remove the protective plate from the coupling unit assembly.

(c) If necessary, remove the end fittings, the blanking plates and the base from
the coupling unit assembly.
NOTE: Removal of a coupling unit assembly:
– cut and discard the holding clips,
– remove the attachment springs,
PRINTED IN FRANCE

– disconnect the coupling unit and the cover.

Page 601
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

(2) Removal of a connector

(a) Male connectors or bases fitted to a sheath assembly

1 Cut and discard the locking clip used to reinforce the joint between the
connector and the sheath assembly.

2 Then loosen the nut, with its snap ring, fitted to the joint.

3 Release the connector from the sheath assembly, pull out all contacts
and remove the dummy cables.

(b) Connector base fitted to the coupling unit assembly

1 Remove the cover from the coupling unit assembly to which the
connector is fitted.

2 Cut and discard the lockwire, then loosen the connector from the base.

3 Loosen the thread-guard nut from the connector using tool H46227.

4 Pull out all contacts and remove the dummy cables.

(3) Removal of a contact
– Cut the cable at the contact and pull out the contact.
NOTE: A contact belonging to a two-lead or three-lead twisted cable may be
replaced separately.
PRINTED IN FRANCE

Page 602
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

(4) Removal of twisted cables, two-lead twisted shielded cables and dummy cables.
NOTE: Since the removal and re-installation operations are carried out at the
same time, they are described in paragraph B "Re-installation".

(5) Removal of a sheath assembly

(a) Remove the cover from the coupling unit assembly to which the sheath is
attached and release the end fitting making the connection.
(b) Remove the corresponding connector from the sheath (see (a) of (2)).

(c) Remove the contacts (see (3)).

NOTE: If the number of contacts is such as to allow them to pass freely thru
the sheath assembly, it is not necessary to remove them when
replacing the latter.
(d) Pull the sheath to remove it.
NOTE: Removal of a sheath assembly:
– Cut and discard the heat-shrinkable and cable marking sleeves,
and the identification and amendment plates in the case of the
main supply sheath.
– Cut and discard the eyelet attachment clip, and remove the eyelet.
– Cut and discard the attachment clips for the end fitting and the
coupling assembly.
– Loosen the end fitting from the sheath using tool H46223.
– Loosen the coupling assembly from the sheath and discard it if it is
defective.
– If it is re-usable, saw the nut associated with the snap ring
lengthwise at the snap ring, and then discard both nut and snap
ring.
PRINTED IN FRANCE

Page 603
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

B. Re-installation

(1) Installation of a routing and coupling assembly (see Figure 601)

(a) Sort the cables which are to be disconnected inside the coupling unit
assembly.
(b) Carefully place them in the coupling unit assembly, direct them towards their
appropriate outlets, then pull them out.

(c) Install the protective plate inside the coupling unit assembly.

(d) Attach the end fitting of the sheath assembly and, if applicable, the connector
base on the coupling unit assembly.

(e) Close off the outlet on the coupling unit assembly which remains open with a
blanking plate.

(f) Close the coupling unit assembly with the appropriate cover when all
associated sheath assemblies and, if applicable, the connector base are in
position.
NOTE: Installation of a coupling unit assembly:
– Attach the closing springs to the coupling unit and reinforce the attachment
with holding clips.
(2) Installation of a sheath assembly (see Figure 602)

(a) Join together corresponding twisted cables and pass them thru the sheath
assembly.
(b) Attach the end fitting of the sheath assembly to the coupling unit assembly.
PRINTED IN FRANCE

Page 604
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NOTE 1: Preparation of a sheath assembly

– Position the protective heat-shrinkable sleeves as shown on
Figure 602.
– Flare the ends of the screened sheaths with flaring pliers to
facilitate the installation of the coupling assembly and the end
fitting.
– Using tool H46223, turn the end fitting on to the sheath.
– Turn the coupling assembly on to the sheath.
– Reinforce the attachments with clips.
– Position the eyelet as shown on Figure 602 and attach it with a
clip.
– Install a marking ring on the sheath and tighten it with tool GS2B.
– Install the identification and amendment plates to the main
supply sheath. Position them as shown on Figure 602 and
tighten them with slotted wrench H46497.
NOTE 2: Preparation of a coupling assembly
– Position the nut associated with the snap ring on the coupling.
– Install the snap ring and peen it over at the hole.

(3) Removal and re-installation of a dummy cable

(a) Do operations (2) (a) and (3), or (2) (b) and (3) of paragraph 1 A "Removal" on
the connectors fitted with dummy cables.

(b) Prepare the replacement dummy cable:

1 Cut a 100 mm (3.9370 in) length of cable of the same type as the cable
in the loom.
PRINTED IN FRANCE

Page 605
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

2 Pull the wire out of that length of cable.

3 Crimp one end of the empty insulation to a contact.

4 Seal the other end of the insulation with a soldering iron.

(c) Engage the contact, complete with the crimped dummy cable, into the
connector.

(4) Removal and re-installation of a twisted cable

NOTE: If only one wire in a twisted cable is defective, the complete two-lead or
three-lead twisted cable must nevertheless be replaced.

(a) Do operations (2) (a) and (3) or (2) (b) and (3) of paragraph 1 A "Removal" on
the ends of the defective cable.

(b) Remove the cover of the coupling unit assembly thru which the defective
cable is routed.
(c) Prepare the replacement wires (see NOTE).

(d) Twist the wires at a pitch of 25 turns per metre (40 in).

(e) Cut the twisted cable to the required length.

(f) Remove insulation of all wires over a length of 4,5 mm (0.1771 in) and solder
the ends of the new cable to the old one. As a precaution, slide a heat-
shrinkable sleeve of the appropriate diameter over the soldered joint.
(g) Pull on the old twisted cable until the heat-shrinkable sleeve appears.

(h) Disconnect the old twisted cable from the new one.
PRINTED IN FRANCE

Page 606
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NOTE: All wires are individually identified (see Figure 603 and Figure 604)
with heat-shrinkable sleeves.

(5) Removal and re-installation of a two-lead twisted shielded cable (1-30)

(a) Do operations (2) (a) and (3), or (2) (b) and (3) of paragraph 1 A "Removal" on
the ends of the defective two-lead cable, and of the shielding sleeves (for
either the crimping or sleeving method).

(b) Remove the cover of the coupling unit assembly thru which the defective
cable is routed.

(c) Prepare the replacement two-lead cable (see NOTE) and the shielding sleeve
1 Continuity of the screening obtained by the crimping method (Crimped
junction (1-40A) or (2-340A)).
BEFORE SB 470-32-810
– Remove insulation of each end of the two-lead cable over a length of
approximately 60 mm (2.3622 in).
– At each of the ends:
. Install a sleeve (1-60) or (2-360) to the shielding.
. Install a shielding end fitting (1-50) or (2-350), approximately 20 mm
7874 in) long, and shrink it with hot air.
AFTER SB 470-32-810
– Remove insulation of each end of the two-lead cable over a length of
approximately 60 mm (2.3622 in).
– Added Mastic Rhodorsil CAF4 under the shielding end fitting (1-50)
before sleeve shrinking.
– At each of the ends:
. Install a sleeve (1-60) or (2-360) to the shielding.
. a shielding end fitting (1-50) or (2-350), approximately 20 mm
7874 in) long, and shrink it with hot air.
PRINTED IN FRANCE

Page 607
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

2 Continuity of the screening obtained by the sleeving method (sleeve

junction (1-40B) or (2-340B))
– Remove insulation of each end of the two-lead cable over a length of
approximately 60 mm (2.3622 in).
– Do the following operations on each end:
. Remove a 100 mm (3.937 in) length of G24 one-lead cable (1-70) or
(2-370), and remove insulation of one of its ends over a length of
4,5 mm (0.1771 in).
. Place the bare end of this length of cable in contact with the
shielding braid. Install a heat-shrinkable sleeve (1-80) or (2-380)
over the point of contact and shrink it with hot air.

(d) Remove insulation of all wires over a length of 4,5 mm (0.1771 in) and solder
the ends of the new two-lead shielded cable to each of the wires of the old one
and the sleeves. As a precaution, slide heat-shrinkable sleeves of the
appropriate diameter over the soldered joints.
(e) Pull on the old two-lead cable until the heat-shrinkable sleeves appear.

(f) Disconnect the old two-lead cable from the new one.
NOTE: All wires are individually identified with heat-shrinkable sleeves, and
their cut lengths are given on Figure 603 and Figure 604.

(6) Installation of a contact

– Remove insulation of the wire to be crimped over a length of 4,5 mm (0.1771 in).
Crimp the contact to the wire.

(7) Installation of a connector

(a) Male connector or base fitted to a sheath assembly (see Figure 602).

1 Engage the crimped contacts.

NOTE: Refer to the wiring schematic diagram (Figure 603 and
Figure 604) to make sure that each crimped contact is engaged
in accordance with the wire marking.
PRINTED IN FRANCE

Page 608
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

2 Place the dummy cables in the pin holes not allocated to a contact.

3 Make sure that all contacts are properly aligned on the same level.

4 Turn the sheath assembly nut, with its snap ring, on to the connector,
and tighten it making sure that the connector locating spigot is correctly
aligned (see Figure 602). Reinforce the joint with an attachment clip.

(b) Connector base fitted to the coupling unit assembly (see Figure 602)

1 Engage the crimped contacts.

NOTE: Refer to the wiring schematic diagram (Figure 603
and Figure 604) to make sure that each crimped contact is
engaged in accordance with the wire marking.

2 Place the dummy cables in the pin holes not allocated to a contact.

3 Make sure that all contacts are properly aligned on the same level.
4 Turn the thread-guard nut on to the connector using tool H46227,
making sure that the connector locating spigot is correctly aligned (see
Figure 602).
5 Attach the connector to its base with screws, complete with lockwire.

6 Attach the base to the coupling unit assembly.

PRINTED IN FRANCE

Page 609
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

2. Protective treatment
A. External protective treatment
Locally repair the protective treatment on aluminium parts by the application of
ALODINE 1200 in accordance with section 14 of Standard Repair Practices 32-09-01.

B. Internal protective treatment

The coupling units, coupling assemblies and end fittings are covered with a protective
layer of blue epoxy resin.
PRINTED IN FRANCE

Page 610
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM
PRINTED IN FRANCE

Routing and coupling assembly

Figure 601

Page 611
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PAGE INTENTIONALLY LEFT BLANK

PRINTED IN FRANCE

Page 612
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
PRINTED IN FRANCE ELECTRICAL LOOM

Loom of L.H. front twin wheel

Figure 602

Page 613/614
32-09-17 JUN 28/91
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM
PRINTED IN FRANCE

Schematic showing the cable length and marking

Loom of the L.H. front twin wheels
Figure 603

Page 615
32-09-17 AUG 29/86
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM
PRINTED IN FRANCE

Schematic showing the cable length and marking

Loom of the R.H. front twin wheels
Figure 604

Page 616
32-09-17 AUG 29/86
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

ASSEMBLY AND STORAGE

NOTE: Equivalent alternatives may be used for listed items.

1. Assembly (not applicable)

2. Storage after assembly

A. Purpose
This paragraph specifies the measures to be taken to give a protection to an electrical
loom in order to obtain its correct operation after storage in temperate continental,
tropical or maritime climates.
These measures are applicable for all modes of transportation (land, air, or sea).

B. General
– Finger prints are to be removed with METHANOL or an equivalent product.

C. Preservation and packaging

(1) Preservation
– Give a protection to the connectors with the caps referred to in the Parts List.
– Attach to the electrical loom an appropriate amount of desiccant, distributed in
several bags, with greaseproof paper placed between the unit and the desiccant.
– Enclose the electrical loom in a heat-sealable cover.
– Place a bag of desiccant and its humidity indicator card against the window
previously cut out in the heat-sealable cloth.
– Remove the air from inside the cover, making the latter fit around the unit as
closely as possible.
– Heat-seal the cover, leaving a strip of cloth wide enough to allow it to be re-used
three times before it needs to be replaced.
PRINTED IN FRANCE

Page 701
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

– Affix to the covering:

– an identification label
– a label stating that the sealed package contains a desiccant and that it should
be opened only when the unit is put into service.

(2) Packaging
– Place the preserved unit in an individual compressed cardboard container.
– Wedge the unit with cellophane shavings.
– Clip the folds of the container and seal open edges with adhesive tape.
– Affix to the container an identification label which mainly bears the storage date
and storage duration, and a label indicating that the sealed package contains
desiccant.
– Place the cardboard container in a heat-sealable covering.
– Hermetically seal the covering.
– Stick, on the covering, the same labels as those affixed to the container.
– Give a protection to these labels by a film of clear varnish.

(3) Storage
Store the component in its packaging.
For electrical looms whose guaranteed storage life has been exceeded, the latter
may be extended subject to a satisfactory inspection of the state of preservation of
a sample taken from the equipment in store.
The duration of this new storage period will depend on the results of the above
inspection.
PRINTED IN FRANCE

Page 702
32-09-17 AUG 29/86
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

D. Removal from store and subsequent testing

(1) Removal from store

– New or overhauled equipment must not be removed from store until it is required
for use, and on a first-in first-out basis.
– Before installation to an aircraft, or at the time of a periodic inspection during
storage, do a visual inspection of the electrical looms, to make sure that the
equipment is satisfactorily preserved.
– In the case of a periodic inspection, renew the preservation of the equipment as
described in the paragraph "Preservation and packaging".
– In the case of installation to an aircraft, remove the anti-rust grease with a rag
and WHITE SPIRIT.
– Remove the storage caps from the connectors.
CAUTION: THE USE OF CHLORINE PRODUCTS IS PROHIBITED.

(2) Tests after removal from store

Not applicable.
PRINTED IN FRANCE

Page 703
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

FITS AND CLEARANCES - TORQUE VALUES NOT APPLICABLE

PRINTED IN FRANCE

Page 801
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

SPECIAL TOOLS, FIXTURES AND EQUIPMENT

The manufacturer uses the test installations and special equipment shown in this section. These
installations and equipment are given as examples, but you can use equivalents.
These special tools and fixtures are available from Messier Services. Inquire at the address that
follows for the current price and delivery time.
Messier Services TELEPHONE: 33 (0) 1 30.67.45.28
Attn: Turnkey Services FAX: 33 (0) 1 30.67.45.95
12, rue Paul Dautier www.messierservices.com
78147 VELIZY CEDEX SITA: PARMBCR
FRANCE CAGE: FAJX6
1. Test equipment
– Electrical test bench Used for the dielectric and conti-
SK30488-1000 nuity tests on the complete loom
assemblies (insulation breakdown,
continuity, insulation, resis-
tance, voltage drop measurement).
– D21972-XXX Interface
Includes all the necessary adap-
ting items for use with the
electrical test bench when
testing the looms.
2. Special tools and equipment
HS358 Stripping pliers
H46223 Tightening handle
Used to tighten and loosen
the connecting adapters

H46227 Tightening handle

Used to attach the base of
receptacles
PRINTED IN FRANCE

H46497 Slotted wrench

To be used to tighten the
identification and amendment
plates

Page 901
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

ILLUSTRATED PARTS LIST (IPL)

PRINTED IN FRANCE

TP 1001
Page 1
32-09-17 MAY 14/82
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

INTRODUCTION
1. Policy
This section is the list of all the components of the unit(s) which are given in this manual, and
permits the identification of these components. It contains, in the form of indexes, detailed
parts list etc., any necessary data for the procurement of any components.

2. How to use the Illustrated Parts List

Each component is identified as follows:

A. By the manufacturer’s Part Number.

The alphanumerical index of the manufacturers’ Part Numbers gives, for each
component, on the same line as the Part Number:
– the figure on which the component is shown,
– the item number,
– the total quantity necessary for each Catalogue Sequence Number (CSN),
– the equivalent Part Number, if applicable, given by the airlines.

B. By the function of the component.

The Illustrated Parts List makes it possible to find the location of each component on the
figures and in the different groups of parts into which the equipment is broken down.
C. By the illustration of the component.
To identify a component by its illustration, use the figure on which this component is
shown. This figure gives the item number which will permit to refer to the Parts List and
get any data about this component.
The Item Numbers have a numerical base. For each figure, the Item Numbers begin at
"1" and are given in numerical sequence with regular increments of tens.
They do not change during the total life of the item. A variant letter is added to the Item
Number as a result of any modification included.
Letter "A" identifies the items of the original version. Usually, variant letters are not
shown on the figures.
PRINTED IN FRANCE

INTRO 1001
Page 1
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

Remarks: when the Illustrated Parts List includes handed assemblies, the Item Number
with numerical base 2 refers to a RH assembly and its variant. The Item
Number with numerical base 1 refers to the LH assembly and its variant.
The numerical order 1, 2, 3, .... 9 is used for the identification of several
assemblies included in a common Illustrated Parts List. Because there is no
direct relationship between these assemblies, these are not variants; but they
include a high percentage of common parts.
For "SELECT FROM" and "OVERSIZE, UNDERSIZE" parts, the "ten"
increments are changed to "five" increments.
The EFFECTIVITY CODE column shows the Item Number of the next higher assembly
or sub-assembly. For items used on the full range of the primary equipment, the
EFFECTIVITY CODE column is kept blank. This column is also kept blank for
assemblies located on a line which is not indented (line 1).
The "UNITS PER ASSY" column shows the quantity per assembly which is necessary
for a next higher assembly. In the indexes, the quantity shown refers to the quantity
broken down for a given CSN.

3. Revision

A. When a line is modified, new or deleted, there is a letter "R" at the end of the line (the
date of issue is changed).

B. After each modification of a given item, the numerical Item Number itself does not
change. But the variant letter changes from "A" to "B", then to "C" thru "Z" (do not use
letters "I" and "O").

C. When it is necessary to add a new part, its name must be on the line which agrees with
the correct position of this part in the breakdown of the assembly.
Select its Item Number from open sequences.

D. Addition of new figures (figure variants):

When the layout of the basic figure does not make it possible to show new parts or the
modified parts in their new form, a new figure (called "figure variant") is then issued.
This figure variant will have the same number as that of the basic figure, suffixed by a
PRINTED IN FRANCE

letter given in alphabetical sequence (do not use "I" and "O").

INTRO 1001
Page 2
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

E. Deletion of items:
Before deletion of items from the Illustrated Parts List:
– make sure, first, that the modification is applied to all the applicable assemblies.
– make sure, for items kept in store, that they are modified or removed from store.
If these two conditions are satisfied, identify the deleted items, in the nomenclature
column, by the word: "DELETED".
The Part Number of the deleted part is then kept in the indexes with the word
"DELETED".

4. Assembly breakdown
The assemblies are broken down and each of their components is shown in the assembly
sequence.
The vertical lines of the indention are shown as dotted lines as follows:
Example: 1 2 3 4 5 6 7
Assembly
. Component of the assembly
. Sub-assembly
. . Component of the sub-assembly
. . . Detail part
This sequence is, in fact, modified by the nomenclature of the attaching parts and storage
parts. The attaching parts are shown immediately below the assembly or sub-assembly they
attach, and above the detail parts.
The storage parts are shown immediately below the parts on which they are installed for
protection.
PRINTED IN FRANCE

INTRO 1001
Page 3
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

The attaching parts and storage parts are:

A. indented in line with the assembly, sub-assembly or part to which they belong,

B. identified by the words "ATTACHING PARTS" or "STORAGE PARTS" shown on the line
above,

C. followed by three stars shown on the line below.

5. Words and abbreviations used

The most used words and abbreviations are:
– RF – For reference
– SB – Service Bulletin
– SEL FROM – "Select from" parts
– OVERSIZE – UNDERSIZE – "Oversize/undersize" parts
– OPT – Optional
– ALT – Alternate
– SUPSD BY – Superseded by
– SUPSDS – Supersedes
– NHA – Next Higher Assembly
– DET – Detail
– LH and RH – Left Hand and Right Hand
– AR – As required
– NP – Non procurable
– ORDER OVERLGTH MPN – Full P/N of the manufacturer
PRINTED IN FRANCE

INTRO 1001
Page 4
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

VENDOR’S CODE LIST

Code No
(Cage No) NAME AND ADDRESS

VF0189 MESSIER-DOWTY SA
ZONE MILITAIRE
78140-VELIZY VILLACOUBLAY FRANCE

VF0225 SOURIAU
9 R DE LA PORTE DE BUC
78000-VERSAILLES FRANCE

VF0286 TYCO ELECTRONICS FRANCE SAS

29 CHS JULES CESAR
95300-CERGY PONTOISE FRANCE

VF0301 SNECMA MOTEURS (GROUPE SNECMA)

2 BD GENERAL MARTIAL VALIN
75015-PARIS FRANCE

VF0582 SUPERFLEXIT SA
(SUPSD BY VF6101)

VF1983 CONNECTEURS ELECTRIQUES DEUTSCH

17 R LAVOISIER
27000-EVREUX FRANCE

VF3132 ITT INDUSTRIES

1 R LOUIS DE LA VERNE
39100-DOLE FRANCE

VF3341 HELLERMANNTYTON (CABLE MANAGEMENT

PRODUCTS)
GROUPE BOWTHORPE
MINIPARC DU MANET
2 R DES HETRES
78190-TRAPPES FRANCE

VF5200 CONNEXION (STE NOUVELLE DE) SNC SARL

(SEE VF0225)
PRINTED IN FRANCE

VF5442 EADS NORMALISATION STANDARD ASN

37 BD MONTMORENCY
75016-PARIS FRANCE

INTRO 1001
Page 5
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

Code No
(Cage No) NAME AND ADDRESS

VF6101 AERAZUR
2 R MAURICE MALLET
92130-ISSY LES MOULINEAUX FRANCE

VF6162 AMPHENOL SOCAPEX SA

PROMENAGE DE L’ARVE
74311-THYEZ FRANCE

VF6220 RAYCHEM SA
(SEE VF0286)

VF8301 PYLE NATIONAL (CIE)

(SUPSD BY VF6162)

VF8612 MATRIX (SOCIETE)

(SUPSD BY VF0286)

V06090 TYCO ELECTRONICS/RAYCHEM DBA RAYCHEM DIV

DBA RAYCHEM DIV ELECTRONICS
300 CONSTITUTION DRIVE
94025-1164-MENLO PARK U.S.A.

V06383 PANDUIT CORP

17301 RIDGELAND AVE
60477-0981-TINLEY PARK U.S.A.
PRINTED IN FRANCE

INTRO 1001
Page 6
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

D142-51 01 080A 2
02 380A 2
D22367000
SUPSD BY D22367000-1
D22367000-1
SUPSDS D22367000
SUPSD BY D22367000-2
D22367000-2 01 -001C RF R
SUPSDS D22367000-1
D22368000
SUPSD BY D22368000-1
D22368000-1
SUPSDS D22368000
SUPSD BY D22368000-2
D22368000-2 01 -002C RF R
SUPSDS D22368000-1
D54411 02 150A 1
02 490A 1
D54413 02 110A 2
02 450A 2
D54414 02 120A 2
02 460A 2
D54428 02 220A 1
D54429 01 310A 1
D54437 01 270A 1
D54439 02 200A 1
D54440 01 280A 1
D54444 01 160A 1
D54691 02 100A 1
02 440A 1
D54694 01 170A 1
D54698 01 290A 1
D54699 02 210A 1
D54727 02 240A 1
D54731 02 -241A 1
D54811 R
SUPSD BY RNF100-3-4-0
PRINTED IN FRANCE

D54819 R
SUPSD BY RNF100-1-0
D54853 02 190A 1
D54853-1 02 190B 1
D54864 R
SUPSD BY NAS1352-04H4P
- Item not illustrated
NUMERICAL INDEX
Page 1
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

D54864 R
SEE NAS1352-04H4P
D54865 01 340A 2 R
02 -330A 1
D54865
SUPSD BY WCF24
D54866
DELETED
D54867
SUPSD BY D92535-1001
D54882 01 150A 1
D54882-1 01 -150B 1
D54891 01 180A 1
02 030A 1
D54892 02 300A 1
D54949 02 310A 1
D54950 01 330A 1
D54951 R
DELETED
D54952 01 -331A 1
D54953 R
DELETED
D54954 02 -311A 1
D54957 01 050A 2
02 350A 2
D54958 01 060A 2
02 360A 2
D54967 01 090A 1
D54968 01 -091A 1
D54979 02 140A 1
02 480A 1
D55073
SEE GA60043
D55085 01 220B 1
D55086 01 -221B 1
D61500-30 R
DELETED
D61500-44 R
PRINTED IN FRANCE

DELETED
D61500-45 R
DELETED
D66164 02 -285A 1

- Item not illustrated

NUMERICAL INDEX
Page 2
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

D92535-1001 R
SUPSDS D54867
SUPSD BY D92732-1001
D92732-1001 02 080C 1 R
SUPSDS D92535-1001
EC14 R
SEE FG797-04-0800
EC22 R
SEE FG797-17-0800
EP10 R
SEE FG797-05-0800
EP18 R
SEE FG797-20-0800
E0052R10B6SWE 01 355A 1 R
E0052R18B32PNE 01 105A 1 R
E0053R16B26SNE 02 395A 1 R
E0053R8B3ASNE 02 265A 1 R
E0261CF20 01 020B AR
E0261CF24 01 010B AR
01 070B AR
02 370B AR
E0272TK24 01 030B AR
FDBA50-16-26SNK R
SEE E0053R16B26SNE
FDBA50-16-26SNK R
DELETED
FDBA50-16-26SNT R
SUPSD BY FDBA50-16-26SNK
FDBA50-8-3ASNK R
DELETED
FDBA50-8-3ASNT R
SUPSD BY FDBA50-8-3ASNK
FDBA50-8-3SNK R
SEE E0053R8B3ASNE
FDBA56-10-6SWK R
SEE E0052R10B6SWE
FDBA56-10-6SWK R
DELETED
PRINTED IN FRANCE

FDBA56-10-6SWT R
SUPSD BY FDBA56-10-6SWK
FDBA56-18-32PNK R
SEE E0052R18B32PNE
FDBA56-18-32PNK R
DELETED
- Item not illustrated
NUMERICAL INDEX
Page 3
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

FDBA56-18-32PNT R
SUPSD BY FDBA56-18-32PNK
FF0995 01 -040A 2
02 -340A 2
FF0996 01 -040B 2
02 -340B 2
FF1048 01 -380A 1
02 -001A RF
FF1048-1B 01 -380B 1
02 -001B RF
FF1048-1C 01 -380C 1 R
02 -001C RF R
FF1049 01 -381A 1
02 -002A RF
FF1049-2B 01 -381B 1
02 -002B RF
FF1049-2C 01 -381C 1 R
02 -002C RF R
FG797-04-0800 01 360A 1 R
FG797-05-0800 02 280A 1 R
FG797-17-0800 01 110A 1 R
FG797-20-0800 02 -420A 1
GA60040 02 -090A 1
02 -430A 1
GA60043 02 130A 2
02 470A 2
GA60044 02 -180A 1
GA60044-1 02 -180B 1
GA60058 01 -260A 1
GA60298 02 -051A 1
GA60299 02 050A 1
GA60315 01 -140A 1
GA60315-1 01 -140B 1
GA60339 01 -120A 1
GA60340 01 -240A 1
GA60341 02 -010A 1
GA60342 02 -160A 1
GA60343 02 -011A 1
PRINTED IN FRANCE

GA60344 02 -161A 1
GA60345 01 -241A 1
GA60346 01 -121A 1
MBL10A8-3AS R
SEE E0053R8B3ASNE

- Item not illustrated

NUMERICAL INDEX
Page 4
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

MBL10R16-26S R
SEE E0053R16B26SNE
MBL16A10-6SW R
SEE E0052R10B6SWE
MBL16A18-32P R
SEE E0052R18B32PNE
NAS1352-04H4P 02 400A 4 R
SUPSDS D54864
NAS5900-6 02 270A 4
NSA935012AKB20 01 -020A AR
NSA935012AKB24 01 -010A AR
01 -070A AR
02 -370A AR
NSA935214TJB24 01 -030A AR
PVW0R16-26SN57 R
SEE E0053R16B26SNE
PVW0R8-98SN57 R
SEE E0053R8B3ASNE
PVW6R10-6SW57 R
SEE E0052R10B6SWE
PVW6R18-32PN57 R
SEE E0052R18B32PNE
RNF100-1-0 02 040A 1 R
SUPSDS D54819
RNF100-3-4-0 01 300A 1 R
SUPSDS D54811
SFM190NR R
SEE RNF100-3-4-0
SFM254NR R
SEE RNF100-1-0
SF090-3-10 01 250A AR
SF090-3-16 01 130A AR
02 020A AR
SF090-3-6 02 170A AR
SN201F08V 02 250A 1
SST1-5M 01 210A 1 R
SUPSDS SST1-5MC
SST1-5MC R
PRINTED IN FRANCE

SUPSD BY SST1-5M
SST2S 02 155A 1 R
02 500A 1 R
WCF24
SEE D54865

- Item not illustrated

NUMERICAL INDEX
Page 5
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

WCF24 R
DELETED
00-200-1439 01 200B 1
SUPSDS 175N254
006-0909-16 02 320A 1 R
SUPSDS 38002-16
025-0462-000 R
SEE FG797-05-0800
025-0468-000 R
SEE FG797-20-0800
025-0486-000 R
SEE FG797-17-0800
025-0611-000 R
SEE FG797-04-0800
057-7597-000 R
SEE 006-0909-16
1262-55-08-15Q R
SEE FG797-05-0800
1262-55-10-11Q R
SEE FG797-04-0800
175N254 R
SUPSD BY 00-200-1439
23320CA080 02 410A AR
260A11-10-6SDW R
SEE E0052R10B6SWE
260A17-8-3ASDN R
SEE E0053R8B3ASNE
38002-16 R
SUPSD BY 006-0909-16
620-858-310-0 02 -230A 2
620-858-312-0 01 -320A 2
620-858-317-0 01 -190A 2
02 -060A 2
620-858-510-0 02 230B 2
620-858-512-0 01 320B 2
620-858-517-0 01 190B 2
02 060B 2
649-371-010-0 02 290A 1
PRINTED IN FRANCE

649-371-011-0 01 370A 1
649-371-015-0 01 230A 1
8500-5585 R
SEE FG797-05-0800
8500-5589 R
SEE FG797-20-0800
- Item not illustrated
NUMERICAL INDEX
Page 6
N 32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

NUMERICAL INDEX

FIGURE TTL
PART NUMBER AIRLINE PART NUMBER ITEM REQ

8500-5595 R
SEE FG797-04-0800
8500-5599 R
SEE FG797-17-0800
852-01R16 R
SEE 006-0909-16
8525-10R16B26SNH R
SEE E0053R16B26SNE
8525-10R8B3ASNH R
SEE E0053R8B3ASNE
8525-16R10B6SWH R
SEE E0052R10B6SWE
8525-16R18B32PNH R
SEE E0052R18B32PNE
PRINTED IN FRANCE

- Item not illustrated

NUMERICAL INDEX
Page 7
N 32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

360
355

110

105
PRINTED IN FRANCE

Figure 1

Page 1001-00
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
01
-001A D22367000 LOOM, LH UPPER FRONT.......... RF R
ELECTRICAL
SUPSD BY D22367000-1
SEE 32-16-11 OR
SEE 32-16-35 OR
SEE 32-16-47 OR
SEE 32-16-51 OR
SEE 32-16-52 OR
SEE 32-16-53 OR
SEE 32-16-56 OR
SEE 32-16-67 OR
SEE 32-16-73 FOR NHA
-001B D22367000-1 LOOM, LH UPPER FRONT.......... RF R
ELECTRICAL
SUPSDS D22367000
SUPSD BY D22367000-2
POST SB 470-32-777
SEE 32-16-11 OR
SEE 32-16-35 OR
SEE 32-16-47 OR
SEE 32-16-51 OR
SEE 32-16-52 OR
SEE 32-16-53 OR
SEE 32-16-56 OR
SEE 32-16-67 OR
SEE 32-16-73 FOR NHA
-001C D22367000-2 LOOM, LH UPPER FRONT.......... RF R
ELECTRICAL
SUPSDS D22367000-1
POST SB 470-32-807
P/N AMDT A
POST SB 470-32-810
SEE 32-16-11 OR
SEE 32-16-35 OR
SEE 32-16-47 OR
SEE 32-16-51 OR
SEE 32-16-52 OR
PRINTED IN FRANCE

SEE 32-16-53 OR
SEE 32-16-56 OR
SEE 32-16-67 OR
SEE 32-16-73 FOR NHA

- Item not illustrated

Page 1001-01
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
01
-002A D22368000 LOOM, RH UPPER FRONT.......... RF R
ELECTRICAL
SUPSD BY D22368000-1
SEE 32-16-11 OR
SEE 32-16-35 OR
SEE 32-16-47 OR
SEE 32-16-51 OR
SEE 32-16-52 OR
SEE 32-16-53 OR
SEE 32-16-56 OR
SEE 32-16-67 OR
SEE 32-16-73 FOR NHA
-002B D22368000-1 LOOM, RH UPPER FRONT.......... RF R
ELECTRICAL
SUPSDS D22368000
SUPSD BY D22368000-2
POST SB 470-32-777
SEE 32-16-11 OR
SEE 32-16-35 OR
SEE 32-16-47 OR
SEE 32-16-51 OR
SEE 32-16-52 OR
SEE 32-16-53 OR
SEE 32-16-56 OR
SEE 32-16-67 OR
SEE 32-16-73 FOR NHA
-002C D22368000-2 LOOM, RH UPPER FRONT.......... RF R
ELECTRICAL
SUPSDS D22368000-1
POST SB 470-32-807
P/N AMDT A
POST SB 470-32-810
SEE 32-16-11 OR
SEE 32-16-35 OR
SEE 32-16-47 OR
SEE 32-16-51 OR
SEE 32-16-52 OR
PRINTED IN FRANCE

SEE 32-16-53 OR
SEE 32-16-56 OR
SEE 32-16-67 OR
SEE 32-16-73 FOR NHA
-010A NSA935012AKB24 .CABLE, SINGLE CORE.....VF5442 AR

- Item not illustrated

Page 1001-02
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
01
010B E0261CF24 .CABLE, SINGLE CORE.....VF5442 AR R
MFR IDENT. VF0241
OPT TO MFR IDENT. VF5688
OPT TO MFR IDENT. VF1868
SPEC TO NSA VF5442
-020A NSA935012AKB20 .CABLE, SINGLE CORE.....VF5442 AR
020B E0261CF20 .CABLE, SINGLE CORE.....VF5442 AR
MFR IDENT. VF0241
OPT TO MFR IDENT. VF5688
OPT TO MFR IDENT. VF1868
SPEC TO NSA VF5442
-030A NSA935214TJB24 .CABLE, SHIELDED TWO....VF5442 AR
CORE
030B E0272TK24 .CABLE, SHIELDED TWO....VF5442 AR
CORE
MFR IDENT. VF0241
OPT TO MFR IDENT. VF5688
OPT TO MFR IDENT. VF1868
SPEC TO NSA VF5442
-040A FF0995 .JUNCTION, CRIMPED........(NP) 2
-040B FF0996 .JUNCTION, SLEEVE.........(NP) 2 R
PRE SB 470-32-810
050A D54957 ..FITTING, SHIELDING END...... 40A 1
060A D54958 ..SLEEVE...................... 40A 1
-070A NSA935012AKB24 ..CABLE, SINGLE CORE....VF5442 40B AR R
PRE SB 470-32-810
070B E0261CF24 ..CABLE, SINGLE CORE....VF5442 40B AR R
PRE SB 470-32-810
MFR IDENT. VF0241
OPT TO MFR IDENT. VF5688
OPT TO MFR IDENT. VF1868
SPEC TO NSA VF5442
080A D142-51 ..SLEEVE................V06090 40B 1 R
PRE SB 470-32-810
090A D54967 .SET OF MARKING RINGS, LH..... 1ABC 1 R
-091A D54968 .SET OF MARKING RINGS, RH..... 2ABC 1 R
-095A DELETED R
PRINTED IN FRANCE

-100A DELETED R
-100B DELETED R

- Item not illustrated

Page 1001-03
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
01
105A E0052R18B32PNE .CONNECTOR..............VF5442 1 R
OPT TO FDBA56-18-32PNK MADE
BY VF1983
OPT TO MBL16A18-32P MADE BY
VF8612
OPT TO PVW6R18-32PN57 MADE
BY VF3132
OPT TO 8525-16R18B32PNH
MADE BY VF0225
STORAGE PARTS
110A FG797-17-0800 .CAP, CONNECTOR.........VF1983 1 R
OPT TO EC22 MADE BY VF8612
OPT TO 025-0486-000 MADE BY
VF3132
OPT TO 8500-5599 MADE BY
VF0225
* * *
-120A GA60339 .SHEATH ASSY, LH.............. 1ABC 1 R
-121A GA60346 .SHEATH ASSY, RH.............. 2ABC 1 R
130A SF090-3-16 ..SHEATH................VF0582 AR
-140A GA60315 ..COUPLING ASSEMBLY, STRAIGHT. 1
-140B GA60315-1 ..COUPLING ASSEMBLY, STRAIGHT. 1
150A D54882 ...COUPLING, STRAIGHT.....(NP) 140A 1
-150B D54882-1 ...COUPLING, STRAIGHT.....(NP) 140B 1
160A D54444 ...NUT....................(NP) 1
170A D54694 ...RING, SNAP.............(NP) 1
180A D54891 ..FITTING, END................ 1
-190A 620-858-317-0 ..CLAMP...................(NP) 2 R
190B 620-858-517-0 ..CLAMP.................VF0301 2 R
FOR REPAIR
-200A DELETED R
200B 00-200-1439 ..EYELET...................... 1
210A SST1-5M ..CLAMP.................V06383 1 R
-220A DELETED R
220B D55085 ..TIE, LH IDENTIFICATION...... 120A 1
-221A DELETED R
-221B D55086 ..TIE, RH IDENTIFICATION...... 121A 1
PRINTED IN FRANCE

230A 649-371-015-0 .CLIP...................VF0301 1

-240A GA60340 .SHEATH ASSY, LH.............. 1ABC 1 R
-241A GA60345 .SHEATH ASSY, RH.............. 2ABC 1 R
250A SF090-3-10 ..SHEATH................VF0582 AR
-260A GA60058 ..COUPLING ASSY, ELBOW........ 1

- Item not illustrated

Page 1001-04
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
01
270A D54437 ...COUPLING, ELBOW........(NP) 1 R
280A D54440 ...NUT....................(NP) 1 R
290A D54698 ...RING, SNAP.............(NP) 1 R
300A RNF100-3-4-0 ..SLEEVE, HEAT-.........VF6220 1 R
SHRINKABLE 105MM (4.1339
IN) LGTH
OPT TO SFM190NR MADE BY
VF3341
310A D54429 ..FITTING, END................ 1
-320A 620-858-312-0 ..CLAMP...................(NP) 2 R
320B 620-858-512-0 ..CLAMP.................VF0301 2 R
FOR REPAIR
330A D54950 ..TIE, LH IDENTIFICATION...... 240A 1
-331A D54952 ..TIE, RH IDENTIFICATION...... 241A 1
340A D54865 .CABLE, DUMMY 100MM (3.9369... 2 R
IN) LGTH
MADE FROM WCF24 MADE BY
VF0241
-340B DELETED R
-345A DELETED R
-350A DELETED R
-350B DELETED R
355A E0052R10B6SWE .CONNECTOR..............VF5442 1 R
OPT TO FDBA56-10-6SWK MADE
BY VF1983
OPT TO MBL16A10-6SW MADE BY
VF8612
OPT TO PVW6R10-6SW57 MADE
BY VF3132
OPT TO 260A11-10-6SDW MADE
BY VF8301
OPT TO 8525-16R10B6SWH MADE
BY VF0225
STORAGE PARTS
360A FG797-04-0800 .CAP, CONNECTOR.........VF1983 1 R
OPT TO EC14 MADE BY VF8612
OPT TO 025-0611-000 MADE BY
PRINTED IN FRANCE

VF3132
OPT TO 1262-55-10-11Q MADE
BY VF8301
OPT TO 8500-5595 MADE BY
VF0225
* * *
- Item not illustrated

Page 1001-05
N 32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
01
370A 649-371-011-0 .CLAMP..................VF0301 1 R
-380A FF1048 .SET 01, LH...............(NP) 1A 1
SEE 320917-02 -001A FOR DET
-380B FF1048-1B .SET 01, LH...............(NP) 1B 1
POST SB 470-32-777
SEE 320917-02 -001B FOR DET
-380C FF1048-1C .SET 01, LH...............(NP) 1C 1 R
POST SB 470-32-807
SEE 320917-02 -001C FOR DET
-381A FF1049 .SET 02, RH...............(NP) 2A 1
SEE 320917-02 -002A FOR DET
-381B FF1049-2B .SET 02, RH...............(NP) 2B 1
POST SB 470-32-777
SEE 320917-02 -002B FOR DET
-381C FF1049-2C .SET 02, RH...............(NP) 2C 1 R
POST SB 470-32-807
SEE 320917-02 -002C FOR DET
PRINTED IN FRANCE

- Item not illustrated

Page 1001-06
N 32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

420
155

395

280

265
PRINTED IN FRANCE

500

Figure 2

Page 1002-00
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
02
-001A FF1048 SET 01, LH................(NP) RF
SEE 320917-01 -380A FOR NHA
-001B FF1048-1B SET 01, LH................(NP) RF
POST SB 470-32-777
SEE 320917-01 -380B FOR NHA
-001C FF1048-1C SET 01, LH................(NP) RF R
POST SB 470-32-807
SEE 320917-01 -380C FOR NHA
-002A FF1049 SET 02, RH................(NP) RF
SEE 320917-01 -381A FOR NHA
-002B FF1049-2B SET 02, RH................(NP) RF
POST SB 470-32-777
SEE 320917-01 -381B FOR NHA
-002C FF1049-2C SET 02, RH................(NP) RF R
POST SB 470-32-807
SEE 320917-01 -381C FOR NHA
-010A GA60341 .SHEATH, LH INTERMEDIATE...... 1ABC 1 R
-011A GA60343 .SHEATH, RH INTERMEDIATE...... 2ABC 1 R
020A SF090-3-16 ..SHEATH................VF0582 AR
030A D54891 ..FITTING, END................ 1
040A RNF100-1-0 ..SLEEVE, HEAT-.........VF6220 1 R
SHRINKABLE 105MM (4.1339
IN) LGTH
OPT TO SFM254NR MADE BY
VF3341
050A GA60299 ..TUBE, LH.................... 10A 1
-051A GA60298 ..TUBE, RH.................... 11A 1
-060A 620-858-317-0 ..CLAMP...................(NP) 2 R
060B 620-858-517-0 ..CLAMP.................VF0301 2 R
FOR REPAIR
-080A D54867 .PLATE, IDENTIFICATION........ 1
SUPSD BY D92535-1001
-080B D92535-1001 .PLATE, IDENTIFICATION........ 1 R
SUPSDS D54867
SUPSD BY D92732-1001
080C D92732-1001 .PLATE, IDENTIFICATION........ 1 R
SUPSDS D92535-1001
PRINTED IN FRANCE

-090A GA60040 .UNIT ASSY, COUPLING.......... 1

100A D54691 ..UNIT, COUPLING..........(NP) 1 R
110A D54413 ..SPRING...................... 2
120A D54414 ..CLIP........................ 2

- Item not illustrated

Page 1002-01
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
02
130A GA60043 .PLATE, BLANKING.............. 2
OPT TO D55073
140A D54979 .PLATE........................ 1
150A D54411 .COVER........................ 1
155A SST2S .CLAMP..................V06383 1 R
-160A GA60342 .SHEATH ASSY, LH.............. 1ABC 1 R
-161A GA60344 .SHEATH ASSY, RH.............. 2ABC 1 R
170A SF090-3-6 ..SHEATH................VF0582 AR
-180A GA60044 ..COUPLING ASSY, STRAIGHT..... 1
-180B GA60044-1 ..COUPLING ASSY, STRAIGHT..... 1
190A D54853 ...COUPLING, STRAIGHT.....(NP) 180A 1
190B D54853-1 ...COUPLING, STRAIGHT.....(NP) 180B 1
200A D54439 ...NUT....................(NP) 1
210A D54699 ...RING, SNAP.............(NP) 1
220A D54428 ..FITTING, END................ 1
-230A 620-858-310-0 ..CLAMP...................(NP) 2 R
230B 620-858-510-0 ..CLAMP.................VF0301 2 R
FOR REPAIR
240A D54727 ..TIE, LH IDENTIFICATION...... 160A 1
-241A D54731 ..TIE, RH IDENTIFICATION...... 161A 1
250A SN201F08V .PLATE, RETAINING.......VF5200 1 R
-255A DELETED R
-260A DELETED R
-260B DELETED R
265A E0053R8B3ASNE .CONNECTOR..............VF5442 1 R
OPT TO FDBA50-8-3SNK MADE
BY VF1983
OPT TO MBL10A8-3AS MADE BY
VF8612
OPT TO PVW0R8-98SN57 MADE
BY VF3132
OPT TO 260A17-8-3ASDN MADE
BY VF8301
OPT TO 8525-10R8B3ASNH MADE
BY VF0225
ATTACHING PARTS
270A NAS5900-6 .SCREW........................ 4 R
PRINTED IN FRANCE

* * *

- Item not illustrated

Page 1002-02
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
02
STORAGE PARTS
280A FG797-05-0800 .CAP, CONNECTOR.........VF1983 1 R
OPT TO EP10 MADE BY VF8612
OPT TO 025-0462-000 MADE BY
VF3132
OPT TO 1262-55-08-15Q MADE
BY VF8301
OPT TO 8500-5585 MADE BY
VF0225
* * *
-285A D66164 .SLEEVE....................... 1B 1 R
POST SB 470-32-777 2B
PRE SB 470-32-807
290A 649-371-010-0 .CLAMP..................VF0301 1 R
300A D54892 .BASE......................... 1
310A D54949 .TIE, LH IDENTIFICATION....... 1ABC 1 R
-311A D54954 .TIE, RH IDENTIFICATION....... 2ABC 1 R
320A 006-0909-16 .BACKSHELL..............VF1983 1 R
OPT TO 057-7597-000 MADE BY
VF3132
OPT TO 852-01R16 MADE BY
VF0225
-330A D54865 .CABLE, DUMMY 100MM (3.9369... 1 R
IN) LGTH 100MM (3.9370 IN)
LGTH
MADE FROM WCF24 MADE BY
VF0241
-330B DELETED R
-340A FF0995 .JUNCTION, CRIMPED........(NP) 2
-340B FF0996 .JUNCTION, SLEEVE.........(NP) 2 R
PRE SB 470-32-810
350A D54957 ..FITTING, SHIELDING END...... 340A 1
360A D54958 ..SLEEVE...................... 340A 1
-370A NSA935012AKB24 ..CABLE, SINGLE CORE....VF5442 340B AR R
PRE SB 470-32-810
370B E0261CF24 ..CABLE, SINGLE CORE....VF5442 340B AR R
PRE SB 470-32-810
PRINTED IN FRANCE

MFR IDENT. VF0241

OPT TO MFR IDENT. VF5688
OPT TO MFR IDENT. VF1868
SPEC TO NSA VF5442

- Item not illustrated

Page 1002-03
32-09-17 Apr 30/07
 Messier-Dowty SA
D22367000 , D22368000 COMPONENT MAINTENANCE MANUAL
ELECTRICAL LOOM

PARTS LIST

UNITS
FIG. AIRLINE EFF.
PER
ITEM PART NUMBER PART No. NOMENCLATURE CODE
ASSY.
1234567
02
380A D142-51 ..SLEEVE................V06090 340B 1 R
PRE SB 470-32-810
-385A DELETED R
-390A DELETED R
-390B DELETED R
395A E0053R16B26SNE .CONNECTOR..............VF5442 1 R
OPT TO FDBA50-16-26SNK MADE
BY VF1983
OPT TO MBL10R16-26S MADE BY
VF8612
OPT TO PVW0R16-26SN57 MADE
BY VF3132
OPT TO 8525-10R16B26SNH
MADE BY VF0225
ATTACHING PARTS
400A NAS1352-04H4P .SCREW........................ 4 R
OPT TO D54864
410A 23320CA080 .LOCKWIRE..................... AR R
* * *
STORAGE PARTS
-420A FG797-20-0800 .CAP, CONNECTOR.........VF1983 1 R
OPT TO EP18 MADE BY VF8612
OPT TO 025-0468-000 MADE BY
VF3132
OPT TO 8500-5589 MADE BY
VF0225
* * *
-430A GA60040 .UNIT ASSY, COUPLING.......... 1
440A D54691 ..UNIT, COUPLING..........(NP) 1 R
450A D54413 ..SPRING...................... 2
460A D54414 ..CLIP........................ 2
470A GA60043 .PLATE, BLANKING.............. 2
OPT TO D55073
480A D54979 .PLATE........................ 1
490A D54411 .COVER........................ 1
500A SST2S .CLAMP..................V06383 1 R
PRINTED IN FRANCE

- Item not illustrated

Page 1002-04
N 32-09-17 Apr 30/07