Scribd
Upload
65 views3 pages

W1006: Pier Lounge Type 1 Building Instructions

This document provides assembly instructions for a 1:400 scale pier lounge building model. The model contains a main block section and a separate base section. To assemble the main block, tabs are folded and glued to form the roof, floor and four walls. The base is assembled similarly from tabs to form a floor and four walls. Finally, the base is attached to the main block using tabs and glue to complete the model pier lounge building.

Uploaded by

Infinite flight
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
65 views3 pages

W1006: Pier Lounge Type 1 Building Instructions

This document provides assembly instructions for a 1:400 scale pier lounge building model. The model contains a main block section and a separate base section. To assemble the main block, tabs are folded and glued to form the roof, floor and four walls. The base is assembled similarly from tabs to form a floor and four walls. Finally, the base is attached to the main block using tabs and glue to complete the model pier lounge building.

Uploaded by

Infinite flight
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

W1006: PIER LOUNGE TYPE 1 BUILDING INSTRUCTIONS

Introduction
This model is of lounge buildings suitable for inclusion
as part of a pier or other terminal structure. The
lounges can be connected to other models using
elevated walkways, and jetways can be fitted to them
for embarking passengers.
Each model contains a number of lounges. All are
constructed in an identical manner.

General Notes Fig 3 – Fitting the Second Wall


Read the general building instructions, and then these
instructions, before commencing construction. Apply glue to the three remaining tabs and fit the last
wall (see Fig 4). Ensure that the roof and floor are flush
The diagrams always show the unprinted side of the all round.
card in grey.

Main Block
Fold in the tabs around the roof and floor and then fold
the roof and floor themselves inwards (see Fig 1).

Fig 4 – Fitting the Last Wall

The completed main block assembly should appear as


in Fig 5.

Fig 1 – Folding the Roof and Floor

Apply glue to the first tab on the roof and floor and fit
the side wall to it (see Fig 2). Ensure that the roof and
floor are flush with the top and bottom edges of the
wall. Fig 5 – Main Block Completed

Base
Fold in the tabs around the floor of the base and then
fold the walls. Apply glue to the tabs around the floor
and glue the walls to them one-by-one. Work towards
the small tab on the end of the walls first (see Fig 6).

Fig 2 – Fitting the First Wall

Apply glue to the tabs on the roof and floor along the
next side and fit the next wall to them in a similar Fig 6 – Fitting the First Base Walls
manner (see Fig 3). Fold in the small tab on the end of
the wall.

© DM Aviation Limited 2007 Page 1 W1006-INS


Glue the last wall to the tab on the floor and to the
small tab on the other wall (see Fig 7).

Fig 7 – Fitting the Last Base Wall

Fold in the tabs around the top of the base. It should


appear as in Fig 8 when completed.
Fig 9 – Fitting the Base

Walkways and jetways can be fitted to the pier lounge


to form a complete pier structure. Use the printed
markings on the lounge walls as a guide when fitting to
Fig 8 – Base Completed other structures.

Final Assembly
Apply glue to the tabs around the top of the base and fit
to the bottom of the main block, in the position marked
on the underneath of the floor (see Fig 9). Do not push
the tabs on the base completely flat when applying the
glue, so that they will make contact with the floor
when pushed into place. Apply light pressure to the
base until the glue is set. Fig 10 – Completed Model

© DM Aviation Limited 2007 Page 2 W1006-INS


Airport
Designs W1006: Pier Lounge Type 1 (1:400 Scale)

Main Block

Base

Main Block

Base

© DM Aviation Limited 2007 Sheet 1 of 1 W1006-400-1

You might also like