constructive solutions

Technical Submittal

NITOTILE EP GROUT
(Chemical resistant epoxy grout for tiles)

Fosam Company Limited

Head Office
telephone: fax: email:
PO Box 11081
Jeddah – 21453 +966 (12) 637 5345 +966 (12) 637 5891 fosam@fosroc.com
Saudi Arabia
C.R. No. 31273
Paid up Capital: SR3,000,000
www.fosroc.com Registered Office: Industrial Area, Phase 4, Road No. 102, Street No. 82
 constructive solutions

Technical Datasheet
Nitotile EP Grout constructive solutions

Chemical resistant epoxy grout for tiles

Uses Instructions for use

As a grout for filling quarry and ceramic tile joints where Surface preparation
chemical and abrasion resistance properties are required
such as laboratories, food processing plants, hospitals, It is important that surfaces should be clean and free from
abattoirs, kitchen and swimming pools etc. dust, loose particles and grease. Oil and grease
contaminated concrete surfaces should be treated with
When fully cured Nitotile EP Grout is impervious to water and Fosroc Chemical Degreaser and then washed well with
other liquids and provides chemical - resistant joints between clean water. Steel surfaces should be grit blasted to SA 2½
walls and floor tiles. The grout may be used in tile joints up and the grout applied within 3 hours of blasting.
to 12 mm wide for internal or external applications.
Mixing
Advantages
The base and hardener components should be individually
stirred to re-disperse any settlement. Base and hardener
 Easy to apply - fast application possible.
should then be mixed until a uniform grey paste is obtained.
 Easy to clean-up during application - can be washed off The filler should then be incorporated using a slow speed
with water until initial set. drill and paddle.

 Long work life - gives long adjustability time. Applications

 Waterproof - unaffected by water when cured. The mixed grout should then be applied rubber trowel,
sweeping the grouting paste into the joints. Alternatively
 Interior or exterior use. use the hand operated gun to fill in the joints. Ensure that
all the joints are completely filled.
 Chemical resistant - excellent resistance to acid and
alkalis.
After about 30 minutes or prior to the expiry of pot life of the
 High bond strength to steel, concrete and tiles. grout, clean the excess grout with a cellulose sponge and
clean warm water to provide neat finish surfaces.
 Suitable for use in Middle East conditions.
Cleaning
 Attractive colours are available on request for sufficient
quantity. The grout can be removed from tiles and tools before initial
set using a damp rag. After initial set Fosroc Solvent 102
Description and/or mechanical removal is necessary.

Nitotile EP Grout is a 3 component solvent free epoxy resin Packaging

based grout consisting of a white base, a black hardener, and
specially selected fine fillers. The components are mixed A 12 kg pack containing Base, Hardener and Filler gives
together to give a smooth, non-slump paste grout of light grey approximately 6 litres mixed material.
colour.
Coverage
Properties
For 2 mm joints between 152 x 152 x 5.5 mm wall tiles, 12
2
Specific gravity: kg pack will be sufficient for to grout approximately 60 m .
2.0
Colour (mix material): Light grey
o o Precautions
@ 20 C @ 35 C
Pot life: 2 hours 1 hour Health and safety
Initial set: 8 hours 4 hours
Initial cure: 24 hours 16 hours Some people are sensitive to epoxy resin and may develop
Full cure: 7 days 4 days dermatitis.
Test Nitotile
Method EP Grout Direct contact with eyes will cause irritation and may cause
Compressive strength: 2 serious damage if left untreated. Any eye contamination
ASTM C579-75 70 N/mm
2 should be washed thoroughly with water and immediate
Tensile strength: ASTM C307-61 17 N/mm
2 medical attention sought.
Bond shear strength: ANSI A118.3 7 N/mm
E5.5

Page 1
Nitotile EP Grout
Gloves and barrier creams, e.g. Kerodex 71 or Rozalex 9 Technical support
should always be used when handling Nitotile EP Grout. If
contact with skin occurs resin removing creams such as The company provides a technical advisory service for on
Kerocleanse 22 or Rozalex 42 should be used followed by site assistance and for advice on evaluation trials and
washing with soap and water. Do not use Solvent. dispensing equipment.

Nitotile EP Grout contains no toxic materials but care should

be taken to avoid inhalation of dust and to prevent material Additional information
entering the eyes. Powder material should be handled to
minimise dust formation, use light mask if excessive dust is Nitotile EP Grout is part of a range of Fosroc tile adhesives
unavoidable. and tile grouts. In addition, Fosroc manufactures a range of
complementary products which includes water proofing
Flash points membranes, joint sealants, grouting, anchoring and
specialised flooring materials.
(Able closed cup method IP33)
Additionally, a wide range for products specifically designed
o
Nitotile EP Grout Base: Over 100 C for the repair and refurbishment of damaged reinforced
o
Nitotile EP Grout Hardener: Over 100 C concrete is available. This includes hand-placed and spray
Nitotile EP Grout Filler: Not applicable grade repair mortars, fluid micro-concretes, chemical
Fosroc Solvent 102: o
37 C resistant epoxy mortars and a comprehensive package of
protective coatings.

Storage For further information please contact your local Fosroc

office.
Shelf life 12 months under normal ambient conditions.

Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous
control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products,
whether or not in accordance with any advice, specification, recommendation of information given by it.

Fosam Company Limited

Head Office Telephone: +966 2 637 5345 Fax: +966 2 637 5891 email: fosam@fosroc.com
Post Box 11081 Regional Offices
Jeddah – 21453 Jeddah Sales Office Tel: (02) 608 0999 Fax: (02) 638 0693 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Jeddah Showroom Tel: (02) 665 0187 Fax: (02) 667 4844 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Saudi Arabia Riyadh Tel: (01) 482 9303 Fax: (01) 482 7562 Medinah Tel: (04) 855 0091 Fax: (04) 855 0047
Dammam Tel: (03) 814 1282 Fax: (03) 814 1581 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875
www.fosroc.com Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2 FO SA/NITOTILE EP GROUT/09/11/09/B
 constructive solutions

Material Safety
Datasheet
Revision date: 10/11/2015 Revision: 02

SAFETY DATA SHEET

NITOTILE EP GROUT BASE

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name NITOTILE EP GROUT BASE

Product number M2016000

1.2. Relevant identified uses of the substance or mixture and uses advised against
1.3. Details of the supplier of the safety data sheet
Supplier FOSAM COMPANY LTD
Phase 4,Road 414 , Street 82
Post Box 11081 Jeddah 21453
K.S.A
+966126375345
+966126080999
+966126375891

1.4. Emergency telephone number

Emergency telephone +966 126375345 , +966216080999

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification
Physical hazards Not Classified

Health hazards Skin Irrit. 2 - H315 Eye Irrit. 2 - H319 Skin Sens. 1 - H317

Environmental hazards Aquatic Chronic 2 - H411

Classification (67/548/EEC or Xi;R36/38. R43. N;R51/53.

1999/45/EC)

2.2. Label elements

Pictogram

Signal word Warning

Hazard statements H317 May cause an allergic skin reaction.

H411 Toxic to aquatic life with long lasting effects.
H319 Causes serious eye irritation.
H315 Causes skin irritation.

1/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

Precautionary statements P264 Wash contaminated skin thoroughly after handling.

P280 Wear protective gloves/protective clothing/eye protection/face protection.
P302+P352 IF ON SKIN: Wash with plenty of water.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P391 Collect spillage.
P501 Dispose of contents/container in accordance with national regulations.

Contains EPOXY RESIN (Type A) (Number average MW <= 700 ), OXIRANE, MONO [(C12-14-
ALKYLOXY)METHYL] DERIVS

Supplementary precautionary P261 Avoid breathing vapour/spray.

statements P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P321 Specific treatment (see medical advice on this label).
P332+P313 If skin irritation occurs: Get medical advice/attention.
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 If eye irritation persists: Get medical advice/attention.
P362+P364 Take off contaminated clothing and wash it before reuse.

2.3. Other hazards

None under normal condition.

SECTION 3: Composition/information on ingredients

3.2. Mixtures

EPOXY RESIN (Type A) (Number average MW <= 700 ) 60-100%

CAS number: 25068-38-6 EC number: 500-033-5

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
Skin Sens. 1 - H317
Aquatic Chronic 2 - H411

OXIRANE, MONO [(C12-14- ALKYLOXY)METHYL] DERIVS 5-10%

CAS number: 68609-97-2

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
Skin Sens. 1 - H317

FUMED SILICA 5-10%

CAS number: 7631-86-9 EC number: 231-545-4

Classification Classification (67/548/EEC or 1999/45/EC)

Not Classified -

2/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

TITANIUM DIOXIDE <1%

CAS number: 13463-67-7 EC number: 236-675-5

Classification Classification (67/548/EEC or 1999/45/EC)

Not Classified -

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.
Composition comments epoxy resin, butanediol-1,4-diglycidylether.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation Remove affected person from source of contamination.

Ingestion Do not induce vomiting.

Call for medical advice immediately; show the container or the label.

Skin contact Remove contaminated clothing and rinse skin thoroughly with water.

Eye contact Irrigate immediately with copious quantities of water for several minutes. Obtain medical
attention urgently.

4.2. Most important symptoms and effects, both acute and delayed
4.3. Indication of any immediate medical attention and special treatment needed
SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media Carbon dioxide, powder foam or water fog - Do not use water jets.

5.2. Special hazards arising from the substance or mixture

Hazardous combustion Toxic fumes. For further information see Section 10.
products

5.3. Advice for firefighters

Protective actions during Fight advanced or massive fires from safe distance or protected location.
firefighting

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Wear protective clothing as described in Section 8 of this safety data sheet.

6.2. Environmental precautions

Environmental precautions Prevent entry into drains, sewers and water courses.

6.3. Methods and material for containment and cleaning up

Methods for cleaning up Soak up with inert absorbent or contain and remove by best available means. Dispose of as
waste.

6.4. Reference to other sections

Reference to other sections For disposal see section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

3/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

Usage precautions Avoid contact with skin and eyes. Do not handle broken packages without protective
equipment.

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Protect from freezing and direct sunlight.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure Controls/personal protection

8.1. Control parameters

Occupational exposure limits
FUMED SILICA
Long-term exposure limit (8-hour TWA): WEL
Short-term exposure limit (15-minute): WEL 2.4 mg/m³
TITANIUM DIOXIDE
Long-term exposure limit (8-hour TWA): WEL 10 mg/m³
WEL = Workplace Exposure Limit

EPOXY RESIN (Type A) (Number average MW <= 700 ) (CAS: 25068-38-6)

DNEL Workers - Inhalation; Short term systemic effects: 12.25 mg/m³

Workers - Inhalation; Long term systemic effects: 12.25 mg/m³

PNEC - Fresh water; 0.006 mg/l

OXIRANE, MONO [(C12-14- ALKYLOXY)METHYL] DERIVS (CAS: 68609-97-2)

DNEL Workers - Inhalation; Long term systemic effects: 3.6 mg/m³

Workers - Dermal; Long term systemic effects: 1 mg/kg bw/day

PNEC - Fresh water; 0.0072 mg/l

- Marine water; 0.00072 mg/l

TITANIUM DIOXIDE (CAS: 13463-67-7)

DNEL Industry - Inhalation; Long term local effects: 10 mg/m³

Consumer - Oral; Long term systemic effects: 700 mg/kg/day

PNEC - Fresh water; 0.127 mg/l

- Sediment (Freshwater); >=1000 mg/kg
- Marine water; 1 mg/l
- Sediment (Marinewater); >= 100 mg/kg
- Soil; 100 mg/kg
- STP; 100 mg/l

8.2. Exposure controls

Protective equipment

4/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

Appropriate engineering Provide adequate ventilation. Avoid inhalation of vapours and spray/mists. Observe any
controls occupational exposure limits for the product or ingredients.

Personal protection Avoid skin and eye contact. Impervious gloves (eg nitrile or neoprene). Goggles (conforming
to EN 166).

Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible. The following protection should be worn: Chemical splash goggles.

Respiratory protection Respiratory protection must be used if the airborne contamination exceeds the recommended
occupational exposure limit.

SECTION 9: Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

Appearance Viscous liquid.

Colour White.

Odour Typical

Flash point >150°C

Relative density 1.15 @ °C

Bulk density Not applicable.

Solubility(ies) Insoluble in water.

9.2. Other information

Other information No additional information.

SECTION 10: Stability and reactivity

10.1. Reactivity
10.2. Chemical stability
Stability Stable.

10.3. Possibility of hazardous reactions

10.4. Conditions to avoid
Conditions to avoid Avoid contact with strong oxidising agents. Strong alkalis. Strong mineral acids.

10.5. Incompatible materials

Materials to avoid Strong alkalis. Strong acids. Strong oxidising agents.

10.6. Hazardous decomposition products

Hazardous decomposition Oxides of carbon. Thermal decomposition or combustion may liberate carbon oxides and
products other toxic gases or vapours.

SECTION 11: Toxicological information

11.1. Information on toxicological effects

5/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

General information The following toxicological assessment is based on a knowledge of the toxicity of the
product's components.
Expected oral LD50, rat > 2g/kg.
Classified as an eye and skin irritant.
Classified as a skin sensitiser.
Health Effects
On Eyes: Irritation.
On Skin: Irritation. May cause sensitisation.
By Inhalation: May cause respiratory irritation.
By Ingestion: May cause irritation of mouth, throat and digestive tract.
Chronic: Repeated and prolonged skin contact may lead to skin disorders.

SECTION 12: Ecological Information

12.1. Toxicity
12.2. Persistence and degradability
Biodegradation Environmental Assessment: When used and disposed of as intended, no adverse
environmental effects are
foreseen.
Mobility: Mobile liquid. Insoluble in water
Persistence and Degradability: Not readily biodegradable.
Bioaccumulative Potential: Has the potential to bioaccumulate.

12.3. Bioaccumulative potential

12.4. Mobility in soil
12.5. Results of PBT and vPvB assessment
12.6. Other adverse effects
SECTION 13: Disposal considerations

13.1. Waste treatment methods

Disposal methods Disposal must be in accordance with local and national legislation.
Unused Product: Dispose of through an authorised waste contractor to a licensed site.
Used/Contaminated Product: As for Unused product.
Packaging: Must be disposed of through an authorised waste contractor.

SECTION 14: Transport information

14.1. UN number
UN No. (ADR/RID) 3082

UN No. (IMDG) 3082

UN No. (ICAO) 3082

UN No. (ADN) 3082

14.2. UN proper shipping name

Proper shipping name ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (CONTAINS EPOXY
(ADR/RID) RESIN (Type A) (Number average MW <= 700 ), OXIRANE, MONO [(C12-14-
ALKYLOXY)METHYL] DERIVS)

Proper shipping name ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (CONTAINS EPOXY
(IMDG) RESIN (Type A) (Number average MW <= 700 ), OXIRANE, MONO [(C12-14-
ALKYLOXY)METHYL] DERIVS)

6/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

Proper shipping name (ICAO) ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (CONTAINS EPOXY
RESIN (Type A) (Number average MW <= 700 ), OXIRANE, MONO [(C12-14-
ALKYLOXY)METHYL] DERIVS)

Proper shipping name (ADN) ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (CONTAINS EPOXY
RESIN (Type A) (Number average MW <= 700 ), OXIRANE, MONO [(C12-14-
ALKYLOXY)METHYL] DERIVS)

14.3. Transport hazard class(es)

ADR/RID class 9

ADR/RID classification code M6

ADR/RID label 9

IMDG class 9

ICAO class/division 9

ADN class 9

Transport labels

14.4. Packing group

ADR/RID packing group III

IMDG packing group III

ADN packing group III

ICAO packing group III

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

14.6. Special precautions for user

EmS F-A, S-F

ADR transport category 3

Emergency Action Code •3Z

Hazard Identification Number 90

(ADR/RID)

Tunnel restriction code (E)

14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture

7/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

Guidance Hazard Label Data:-

Named Ingredients: epoxy resin (number average molecular weight <700)
butanediol-1,4-diglycidylether
UN Number: 3082
Symbol(s): Xi
Risk Phrases: Irritating to eyes and skin
May cause sensitisation by skin contact
Safety Phrases: In case of contact with eyes, rinse immediately with plenty of water and seek
medical
advice.
After contact with skin, wash immediately with plenty of soap and water.
Wear suitable gloves and eye/face protection.
Contains epoxy constituents. See information supplied by the manufacturer.
EC Directives: Dangerous Substances Directive, 67/548/EEC and adaptations.
Dangerous Preparations Directive, 88/379/EEC.
Safety Data Sheets Directive, 91/155/EEC.
Hazardous Waste Directive,91/689/EEC.
Statutory Instruments: Chemicals (Hazard Information and Packaging for Supply)
(Amendment) Regs. 1996 (SI
1092).
Control of Substances Hazardous to Health Regs. 1994 (SI 3246).
Health & Safety at Work, etc. Act 1974.
Environmental Protection Act 1990.
Codes of Practice: Waste Management. The Duty of Care.
Operational Provisions of the Road Traffic (Carriage of Dangerous Substances in packages
etc.) Regs. 1986 (COP 17).
Guidance Notes: Occupational skin diseases: health and safety precautions (EH 26).
Storage of packaged dangerous substances [HS(G)71].
The above publications are available from HMSO

15.2. Chemical safety assessment

SECTION 16: Other information

General information The data and advice given apply when the product is used for the stated application or
applications. The product is not sold as suitable for any other application. Use of the product
for applications other than as stated in this sheet may give rise to risks not mentioned in this
sheet. The product should not be used other than for the stated application or applications
without seeking advice from Fosam Company ( Fosroc).
If this product has been purchased for supply to a third party for use at work, it is the
purchaser's duty to take all necessary steps to secure that any person handling or using the
product is provided with the information in this sheet.
It is the responsibility and duty of the employer to inform employees and others who may be
affected of any hazards described in this sheet and of any precautions which should be taken.
This sheet does not constitute or substitute for the users own assessment of workplace risk,
as required by other health and safety legislation.
Further copies of this Safety Data Sheet may be obtained from Fosroc Fosam Compamy.

Revision date 10/11/2015

Revision 02

SDS number SDS 2016000 KSA

8/9
Revision date: 10/11/2015 Revision: 02

NITOTILE EP GROUT BASE

Risk phrases in full NC Not classified.

R36/38 Irritating to eyes and skin.
R38 Irritating to skin.
R43 May cause sensitisation by skin contact.
R51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.

Hazard statements in full H315 Causes skin irritation.

H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.

The information on this data sheet represents our current data and is reliable provided that the product is used under the
prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance
literature. Any other use of the product which involves using the product in combination with any other product or any other
process is the responsibility of the user.

9/9
Revision date: 10/11/2015 Revision: 01

SAFETY DATA SHEET

NITOTILE EP GROUT FILLER

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name NITOTILE EP GROUT FILLER

Product number M2019003

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Filler component of three part of epoxy resin system

1.3. Details of the supplier of the safety data sheet

Supplier FOSAM COMPANY LTD
Phase 4,Road 414 , Street 82
Post Box 11081 Jeddah 21453
K.S.A
+966126375345
+966126080999
+966126375891

1.4. Emergency telephone number

Emergency telephone +966 126375345 , +966216080999

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification
Physical hazards Not Classified

Health hazards Eye Irrit. 2 - H319

Environmental hazards Not Classified

Classification (67/548/EEC or Xi;R37.

1999/45/EC)

2.2. Label elements

Pictogram

Signal word Warning

Hazard statements H319 Causes serious eye irritation.

1/6
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT FILLER

Precautionary statements P264 Wash contaminated skin thoroughly after handling.

P280 Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P337+P313 If eye irritation persists: Get medical advice/attention.

Contains SILICA SAND

2.3. Other hazards

SECTION 3: Composition/information on ingredients

3.2. Mixtures

SILICA SAND 60-100%

CAS number: 14808-60-7 EC number: 238-878-4

Classification Classification (67/548/EEC or 1999/45/EC)

Eye Irrit. 2 - H319 -
STOT RE 2 - H373

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.
Composition comments silica sands, inert fillers

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation Remove to fresh air, if unconscious, place in recovery position and seek
medical advice.

Ingestion Rinse mouth thoroughly with water. Give plenty of water to drink. Give milk instead of water if
readily available. Never give anything by mouth to an unconscious person.

Skin contact Wash thoroughly with soap and water or suitable skin cleanser as soon as possible.

Eye contact Rinse immediately with plenty of water. Continue to rinse for at least 15 minutes.

4.2. Most important symptoms and effects, both acute and delayed
4.3. Indication of any immediate medical attention and special treatment needed
SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media Extinguish with foam, carbon dioxide, dry powder or water fog.

5.2. Special hazards arising from the substance or mixture

Hazardous combustion Does not decompose when used and stored as recommended.
products

5.3. Advice for firefighters

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Wear protective clothing as described in Section 8 of this safety data sheet.

6.2. Environmental precautions

Environmental precautions Avoid spreading dust or contaminated materials.

6.3. Methods and material for containment and cleaning up

2/6
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT FILLER

Methods for cleaning up No specific clean-up procedure recommended.

6.4. Reference to other sections

Reference to other sections For disposal see section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions Do not handle broken packages without protective equipment.

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Store in tightly-closed, original container. Keep container dry.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure Controls/personal protection

8.1. Control parameters

Occupational exposure limits
SILICA SAND
Long-term exposure limit (8-hour TWA): WEL 0,1 mg/m³ Respirable crystalline silica
WEL = Workplace Exposure Limit

8.2. Exposure controls

Protective equipment

Appropriate engineering Provide adequate general and local exhaust ventilation. Observe any occupational exposure
controls limits for the product or ingredients.

Eye/face protection The following protection should be worn: Chemical splash goggles.

Hygiene measures This product contains silica sands.

The grain size distribution of silica sand present means that it is not classified as hazardous.
However, any respirable crystalline dust generated by secondary processing may may cause
health effects.
Prolonged and /or massive inhalation of respirable crystalline silica dust may cause lung
fibrosis, commonly referred to as silicosis. Principal symptoms of silicosis are cough and
breathlessness.
Occupational exposure to respirable crystalline silica dust should be monitored and controlled

Respiratory protection Respiratory protection may be required if excessive airborne contamination occurs.

SECTION 9: Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

Appearance Crystalline powder.

Colour White/off-white.

Bulk density 1.4

Solubility(ies) Insoluble in water.

9.2. Other information

3/6
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT FILLER

SECTION 10: Stability and reactivity

10.1. Reactivity
10.2. Chemical stability
Stability Stable.

10.3. Possibility of hazardous reactions

10.4. Conditions to avoid
10.5. Incompatible materials
Materials to avoid Strong acids. Strong alkalis.

10.6. Hazardous decomposition products

Hazardous decomposition Carbon monoxide (CO).
products

SECTION 11: Toxicological information

11.1. Information on toxicological effects

SECTION 12: Ecological Information

Ecotoxicity The product is not expected to be toxic to aquatic organisms.

12.1. Toxicity
12.2. Persistence and degradability
Biodegradation Environmental Assessment: When used and disposed of as intended, no adverse
environmental effects are
foreseen.
Mobility: Insoluble in water.
Persistence and Degradability: Expected to be readily biodegradable.
Bioaccumulative Potential: Not known.
Ecotoxicity: Not expected to be ecotoxic to fish/daphnia/algae.

12.3. Bioaccumulative potential

12.4. Mobility in soil
12.5. Results of PBT and vPvB assessment
12.6. Other adverse effects
SECTION 13: Disposal considerations

13.1. Waste treatment methods

General information Disposal must be in accordance with local and national legislation.
Unused Product: Must be dumped or incinerated in accordance with local regulations.
Recycle if possible.
Packaging: Destroy packaging by incineration at an approved waste disposal site.

SECTION 14: Transport information

General The product is not covered by international regulations on the transport of dangerous goods
(IMDG, IATA, ADR/RID).

14.1. UN number
Not applicable.

14.2. UN proper shipping name

Not applicable.

4/6
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT FILLER

14.3. Transport hazard class(es)

No transport warning sign required.

14.4. Packing group

Not applicable.

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

No.

14.6. Special precautions for user

Not applicable.

14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
Guidance CHIP for everyone HSG (108)
Hazard Label Data:-
Named Ingredients: cement powders
Symbol(s): Xi
Risk Phrases: Irritating to eyes, respiratory system and skin.
Safety Phrases: Do not breathe dust
Avoid contact with skin and eyes
Wear suitable gloves and eye/face protection
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
After contact with skin, wash immediately with plenty of soap and water
EC Directives: Dangerous Substances Directive, 67/548/EEC and adaptations.
Dangerous Preparations Directive, 88/379/EEC.
Safety Data Sheets Directive, 91/155/EEC.
Statutory Instruments: Chemicals (Hazard Information and Packaging for Supply)
(Amendment) Regs. 1996 (SI
1092).
Health & Safety at Work, etc. Act 1974.
Control of Substances Hazardous to Health Regs. 1994 (SI 3246).
Codes of Practice: Waste Management. The Duty of Care.
Guidance Notes: Occupational skin diseases: health and safety precautions (EH 26).
Dust in the workplace: general principles of protection. (EH44).
Occupational exposure limits (EH 40).
The above publications are available from HMSO

15.2. Chemical safety assessment

SECTION 16: Other information

5/6
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT FILLER

General information The data and advice given apply when the product is used for the stated application or
applications. The product is not sold as suitable for any other application. Use of the product
for applications other than as stated in this sheet may give rise to risks not mentioned in this
sheet. The product should not be used other than for the stated application or applications
without seeking advice from Fosam Company ( Fosroc).
If this product has been purchased for supply to a third party for use at work, it is the
purchaser's duty to take all necessary steps to secure that any person handling or using the
product is provided with the information in this sheet.
It is the responsibility and duty of the employer to inform employees and others who may be
affected of any hazards described in this sheet and of any precautions which should be taken.
This sheet does not constitute or substitute for the users own assessment of workplace risk,
as required by other health and safety legislation.
Further copies of this Safety Data Sheet may be obtained from Fosroc Fosam Compamy.

Revision date 10/11/2015

Revision 01

SDS number SDS M2019003 KSA

Risk phrases in full R37 Irritating to respiratory system.

Hazard statements in full H319 Causes serious eye irritation.

H373 May cause damage to organs through prolonged or repeated exposure.

The information on this data sheet represents our current data and is reliable provided that the product is used under the
prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance
literature. Any other use of the product which involves using the product in combination with any other product or any other
process is the responsibility of the user.

6/6
Revision date: 10/11/2015 Revision: 01

SAFETY DATA SHEET

NITOTILE EP GROUT HARDENER

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name NITOTILE EP GROUT HARDENER

Product number M2016042

CAS number 25620-58-0

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Hardener Component of Three Part Epoxy Tile Adhesive Syastem

1.3. Details of the supplier of the safety data sheet

Supplier FOSAM COMPANY LTD
Phase 4,Road 414 , Street 82
Post Box 11081 Jeddah 21453
K.S.A
+966126375345
+966126080999
+966126375891

1.4. Emergency telephone number

Emergency telephone +966 126375345 , +966216080999

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification
Physical hazards Not Classified

Health hazards Acute Tox. 4 - H302 Skin Corr. 1B - H314 Eye Irrit. 2 - H319 Skin Sens. 1 - H317 Repr. 1B -
H360

Environmental hazards Aquatic Acute 1 - H400 Aquatic Chronic 1 - H410

Classification (67/548/EEC or Carc. Cat. 2;R45,Repr. Cat. 2;R61. Xn;R21/22,R68/20/21/22. Muta Cat. 3;R68. C;R34. R43.
1999/45/EC) R52/53.

2.2. Label elements

Pictogram

Signal word Danger

1/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

Hazard statements H410 Very toxic to aquatic life with long lasting effects.
H302 Harmful if swallowed.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H360 May damage fertility or the unborn child.
H319 Causes serious eye irritation.

Precautionary statements P261 Avoid breathing vapour/spray.

P264 Wash contaminated skin thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.

Contains ISOPHORONEDIAMINE, EPOXY RESIN DILUENT, POLYMER OF C-18 UNSATURATED

FATTY ACID DIMER WITH TRIETHYLENETETRAMINE & TALL OIL FATTY ACIDS,
DIBUTYL PHTHALATE: DBP, TRIETHYLENETETRAMINE

Supplementary precautionary P201 Obtain special instructions before use.

statements P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe vapour/spray.
P272 Contaminated work clothing should not be allowed out of the workplace.
P301+P310 IF SWALLOWED: Immediately call a POISON CENTER/doctor.
P301+P330+P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P302+P352 IF ON SKIN: Wash with plenty of water.
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing.
Rinse skin with water/shower.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P308+P313 IF exposed or concerned: Get medical advice/attention.
P321 Specific treatment (see medical advice on this label).
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 If eye irritation persists: Get medical advice/attention.
P362+P364 Take off contaminated clothing and wash it before reuse.
P363 Wash contaminated clothing before reuse.
P391 Collect spillage.
P405 Store locked up.
P501 Dispose of contents/container in accordance with national regulations.

2.3. Other hazards

SECTION 3: Composition/information on ingredients

3.2. Mixtures

ISOPHORONEDIAMINE 30-60%
CAS number: 2855-13-2 EC number: 220-666-8 REACH registration number: 01-
2119514687-32-xxxx

Classification
Acute Tox. 4 - H302
Acute Tox. 4 - H312
Skin Corr. 1B - H314
Skin Sens. 1 - H317
Aquatic Chronic 3 - H412

2/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

EPOXY RESIN DILUENT 30-60%

CAS number: 68512-30-1 EC number: 270-966-8

Classification
Acute Tox. 4 - H302

POLYMER OF C-18 UNSATURATED FATTY ACID DIMER 10-30%

WITH TRIETHYLENETETRAMINE & TALL OIL FATTY
ACIDS
CAS number: 68082-29-1

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
Skin Sens. 1 - H317

FUMED SILICA 1-5%

CAS number: 7631-86-9 EC number: 231-545-4

Classification Classification (67/548/EEC or 1999/45/EC)

Not Classified -

DIBUTYL PHTHALATE: DBP 1-5%

CAS number: 84-74-2 EC number: 201-557-4
M factor (Acute) = 10 M factor (Chronic) = 10

Classification
Repr. 1B - H360
Aquatic Acute 1 - H400
Aquatic Chronic 1 - H410

TRIETHYLENETETRAMINE 1-5%
CAS number: 112-24-3 EC number: 203-950-6

Classification
Acute Tox. 4 - H312
Skin Corr. 1B - H314
Eye Dam. 1 - H318
Skin Sens. 1 - H317
Aquatic Chronic 3 - H412

3/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

4,4'-METHYLENEDIANILINE <1%
CAS number: 101-77-9 EC number: 202-974-4
M factor (Acute) = 1 M factor (Chronic) = 10

Classification
Acute Tox. 3 - H301
Acute Tox. 2 - H330
Skin Sens. 1 - H317
Muta. 2 - H341
Carc. 1B - H350
STOT SE 1 - H370
STOT RE 2 - H373
Aquatic Acute 1 - H400
Aquatic Chronic 1 - H410

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.

SECTION 4: First aid measures

4.1. Description of first aid measures

General information Eyes: Irrigate immediately with copious quantities of water for several minutes. Obtain medical
attention
urgently.
Skin: Wash immediately with soap and water or suitable skin cleanser. Remove contaminated
clothing
immediately.
Inhalation: Remove from exposure.
Ingestion: Wash out mouth with water. Do NOT induce vomiting. Obtain medical attention
urgently. Beware of
aspiration if vomiting occurs.

4.2. Most important symptoms and effects, both acute and delayed
4.3. Indication of any immediate medical attention and special treatment needed
SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media Carbon dioxide, powder foam or water fog - Do not use water jets.

5.2. Special hazards arising from the substance or mixture

Hazardous combustion Toxic gases/vapours/fumes of: Nitrous gases (NOx).
products

5.3. Advice for firefighters

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Wear protective clothing as described in Section 8 of this safety data sheet.

6.2. Environmental precautions

Environmental precautions Prevent entry into drains, sewers and water courses.

6.3. Methods and material for containment and cleaning up

4/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

Methods for cleaning up Soak up with inert absorbent or contain and remove by best available means. Dispose of as
waste.

6.4. Reference to other sections

Reference to other sections For disposal see section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions Good personal hygiene is necessary. Wash hands and contaminated areas with water and
soap before leaving the work site.

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Store in tightly-closed, original container in a well-ventilated place. Keep container dry.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure Controls/personal protection

8.1. Control parameters

Occupational exposure limits
FUMED SILICA
Long-term exposure limit (8-hour TWA): WEL
Short-term exposure limit (15-minute): WEL 2.4 mg/m³
DIBUTYL PHTHALATE: DBP
Long-term exposure limit (8-hour TWA): WEL 5 mg/m³
Short-term exposure limit (15-minute): WEL 10 mg/m³
4,4'-METHYLENEDIANILINE
Long-term exposure limit (8-hour TWA): WEL 0.01 ppm(Sk) 0.08 mg/m3(Sk)
Short-term exposure limit (15-minute): WEL
WEL = Workplace Exposure Limit

EPOXY RESIN DILUENT (CAS: 68512-30-1)

DNEL Workers - Dermal; Long term : 16.4 mg/kg bw/day

Workers - Inhalation; Long term : 57 mg/m³

PNEC - Fresh water; 14 µg/l

- Marine water; 1.4 µg/l
- Intermittent release; 140 µg/l
- STP; 2.4 mg/l
- Sediment; 52.9 mg/kg
- Soil; 10.5 mg/kg dw

ISOPHORONEDIAMINE (CAS: 2855-13-2)

PNEC The product of hydrolysis (methanol) is readily biodegradable. Silicone content is

not biodegradable. - Fresh water; 0.06 mg/l
- Marine water; 0.006 mg/l

DIBUTYL PHTHALATE: DBP (CAS: 84-74-2)

5/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

Ingredient comments WEL = Workplace Exposure Limits

DNEL Workers - Inhalation; Long term systemic effects: 0.13 mg/m³

Workers - Dermal; Long term systemic effects: 0.19 mg/kg bw/day

PNEC - Fresh water; 10 µg/l

- Marine water; 1 µg/l

TRIETHYLENETETRAMINE (CAS: 112-24-3)

PNEC Not available.

8.2. Exposure controls

Protective equipment

Appropriate engineering Provide adequate general and local exhaust ventilation. Observe any occupational exposure
controls limits for the product or ingredients.

SECTION 9: Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

Appearance Viscous liquid.

Colour Black.

Odour Amine.

Flash point > 115 C°C

Relative density 1.125 @ °C

Solubility(ies) Slightly soluble in water.

Auto-ignition temperature > 330 C°C

9.2. Other information

SECTION 10: Stability and reactivity

10.1. Reactivity
10.2. Chemical stability
Stability Stable.

10.3. Possibility of hazardous reactions

10.4. Conditions to avoid
Conditions to avoid Avoid heat. Avoid contact with the following materials: Strong oxidising agents.

10.5. Incompatible materials

Materials to avoid Flammable/combustible materials.

10.6. Hazardous decomposition products

Hazardous decomposition Oxides of carbon. Thermal decomposition or combustion may liberate carbon oxides and
products other toxic gases or vapours.

SECTION 11: Toxicological information

6/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

11.1. Information on toxicological effects

Acute toxicity - oral
ATE oral (mg/kg) 786.16

Acute toxicity - dermal

ATE dermal (mg/kg) 3,302.11

General information The following toxicological assessment is based on a knowledge of the toxicity of the
product's components.
Oral LD50, rat >1000 mg/kg
Health Effects
On Eyes: Causes irreversible damage to eye tissue if not removed promptly.
On Skin: Corrosive - causes burns. May cause sensitisation.
By Inhalation: May cause respiratory irritation.
By Ingestion: Corrosive - causes severe damage to mouth, throat and digestive tract.
Chronic: Prolonged skin contact can result in chemical burns.
Other: p-tertiarybutyl phenol can cause a cosmetic effect known as "occupational vitiligo" or
leucoderma. It is
believed that repeated contact with this substance can lead to this depigmentation of the skin
in
sensitive individuals.

SECTION 12: Ecological Information

Ecotoxicity When used and disposed of as intended, no adverse environmental effects are
foreseen.

12.1. Toxicity
12.2. Persistence and degradability
12.3. Bioaccumulative potential
12.4. Mobility in soil
12.5. Results of PBT and vPvB assessment
12.6. Other adverse effects
SECTION 13: Disposal considerations

13.1. Waste treatment methods

General information Waste should be treated as controlled waste. Dispose of waste to licensed waste disposal site
in accordance with the requirements of the local Waste Disposal Authority.

Disposal methods Disposal must be in accordance with local and national legislation.
Unused Product: Dispose of through an authorised waste contractor to a licensed site. Do not
empty into drains, sewers or water courses.
Used/Contaminated Product: As for Unused product.
Packaging: The method of disposal must be acceptable to the local authority.

SECTION 14: Transport information

14.1. UN number
UN No. (ADR/RID) 2735

UN No. (IMDG) 2735

UN No. (ICAO) 2735

UN No. (ADN) 2735

7/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

14.2. UN proper shipping name

Proper shipping name AMINES, LIQUID, CORROSIVE, N.O.S. (CONTAINS ISOPHORONEDIAMINE, DIBUTYL
(ADR/RID) PHTHALATE: DBP)

Proper shipping name AMINES, LIQUID, CORROSIVE, N.O.S. (CONTAINS ISOPHORONEDIAMINE, DIBUTYL
(IMDG) PHTHALATE: DBP)

Proper shipping name (ICAO) AMINES, LIQUID, CORROSIVE, N.O.S. (CONTAINS ISOPHORONEDIAMINE, DIBUTYL
PHTHALATE: DBP)

Proper shipping name (ADN) AMINES, LIQUID, CORROSIVE, N.O.S. (CONTAINS ISOPHORONEDIAMINE, DIBUTYL
PHTHALATE: DBP)

14.3. Transport hazard class(es)

ADR/RID class 8

ADR/RID classification code C7

ADR/RID label 8

IMDG class 8

ICAO class/division 8

ADN class 8

Transport labels

14.4. Packing group

ADR/RID packing group II

IMDG packing group II

ADN packing group II

ICAO packing group II

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

14.6. Special precautions for user

EmS F-A, S-B

ADR transport category 2

Emergency Action Code 2X

Hazard Identification Number 80

(ADR/RID)

Tunnel restriction code (E)

14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code

8/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

Transport in bulk according to Not applicable.

Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
Guidance Introduction to Local Exhaust Ventilation HS(G)37.
Workplace Exposure Limits EH40.
Hazard Label Data:-
This product is NOT classified as dangerous for supply in the UK.
EC Directives: Dangerous Substances Directive, 67/548/EEC and adaptations.
Dangerous Preparations Directive, 88/379/EEC.
Safety Data Sheets Directive, 91/155/EEC.
Statutory Instruments: Chemicals (Hazard Information and Packaging for Supply)
(Amendment) Regs. 1996 (SI
1092).
Control of Substances Hazardous to Health Regs. 1994 (SI 3246).
Environmental Protection (Duty of Care) Regs. 1991 (SI 2839).
Codes of Practice: Waste Management. The Duty of Care.
The above publications are available from HMSO

15.2. Chemical safety assessment

SECTION 16: Other information

General information The data and advice given apply when the product is used for the stated application or
applications. The product is not sold as suitable for any other application. Use of the product
for applications other than as stated in this sheet may give rise to risks not mentioned in this
sheet. The product should not be used other than for the stated application or applications
without seeking advice from Fosam Company ( Fosroc).
If this product has been purchased for supply to a third party for use at work, it is the
purchaser's duty to take all necessary steps to secure that any person handling or using the
product is provided with the information in this sheet.
It is the responsibility and duty of the employer to inform employees and others who may be
affected of any hazards described in this sheet and of any precautions which should be taken.
This sheet does not constitute or substitute for the users own assessment of workplace risk,
as required by other health and safety legislation.
Further copies of this Safety Data Sheet may be obtained from Fosroc Fosam Compamy.

Revision date 10/11/2015

Revision 01

SDS number SDS 2016042 KSA

9/10
Revision date: 10/11/2015 Revision: 01

NITOTILE EP GROUT HARDENER

Risk phrases in full NC Not classified.

R21 Harmful in contact with skin.
R21/22 Harmful in contact with skin and if swallowed.
R22 Harmful if swallowed.
R34 Causes burns.
R39/23/24/25 Toxic: danger of very serious irreversible effects through inhalation, in contact
with skin and if swallowed.
R43 May cause sensitisation by skin contact.
R45 May cause cancer.
R48/20/21/22 Harmful: danger of serious damage to health by prolonged exposure through
inhalation, in contact with skin and if swallowed.
R50 Very toxic to aquatic organisms.
R51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
R61 May cause harm to the unborn child.
R62 Possible risk of impaired fertility.
R68 Possible risk of irreversible effects.
R68/20/21/22 Harmful: possible risk of irreversible effects through inhalation, in contact with
skin and if swallowed.

Hazard statements in full H301 Toxic if swallowed.

H302 Harmful if swallowed.
H312 Harmful in contact with skin.
H314 Causes severe skin burns and eye damage.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H319 Causes serious eye irritation.
H330 Fatal if inhaled.
H341 Suspected of causing genetic defects.
H350 May cause cancer.
H360 May damage fertility or the unborn child.
H370 Causes damage to organs .
H373 May cause damage to organs through prolonged or repeated exposure.
H400 Very toxic to aquatic life.
H410 Very toxic to aquatic life with long lasting effects.
H412 Harmful to aquatic life with long lasting effects.

The information on this data sheet represents our current data and is reliable provided that the product is used under the
prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance
literature. Any other use of the product which involves using the product in combination with any other product or any other
process is the responsibility of the user.

10/10
 constructive solutions

Test Reports
 constructive solutions

Job References
 Job References for Nitotile EP Grout
Sorted by ascending Project Category and ascending Project Date

Project Title Sector Segment Main Contructor Country Quantity Units Date
AQWAT (AL BAIK FACTORY) - JEDDAH Utilities Power YOUSSEF MARROUN Saudi Arabia 4200 12kg Packs 2017
CONTRACTING EST
JSTPP - JEDDAH Utilities Power SAUDI ARCHIRODON Saudi Arabia 1000 12kg Packs 2016
LIMITED -
JSTPP - JEDDAH Utilities Power GUSAN CONSTRUCTION Saudi Arabia 1500 12kg Packs 2015
ARABIA CO. LTD. - JSTPP
DESALINATION PLANT - RAS AL KHAIR Utilities Water ASSAD SAID CORP FOR Saudi Arabia 700 12kg Packs 2014
CONTRACTING -

LULU HYPER MARKET Buildings Commerical Namal cont Saudi Arabia 1,200 Kilogram(s) 2013

Power Oil, Gas,

POWER PLANT Utilities Arabian Bemco Saudi Arabia 50 Pack 2009
Coal

ARAMCO - ABQIQ GOSP 5 & 6 PROJECTS Industrial Oil & Gas Al-OSAIS Contracting Saudi Arabia 6 Pack 2007

INDOMI FACTORY Industrial Clean Industries Asharq Al-Baeid Saudi Arabia 13 Pack 2007

Power Oil, Gas,

JEBEL ALI POWER STATION "L-1" Utilities Al Ghandi CCC UAE 3,600 Litre(s) 2005
Coal
Power Oil, Gas, Square
POWER PLANT 9 Utilities General Electric Saudi Arabia 200 2000
Coal Metre(s)
 constructive solutions

Approvals
 constructive solutions

Case Histories
 CASE STUDY

constructive solutions
SWRO Desalination
Plant Phase II
King Fahad Industrial Port Jubail

Saudi Arabia
Client
Marafiq
Sector
Water & Power
DATE
March 2014

PRODUCTS
 Nitotile 489
 Nitotile EP Grout

THE PROJECT
The Jubail SWRO Phase II, a continuation of the Al Fatah Water and Power project in Jubail,
has a design capacity of 58,500 m³/day and is projected to be completed by April 30, 2014.

This dual membrane plant with UF followed by reverse osmosis (RO) will be the largest UF-RO
desalination plant in Saudi Arabia. With a UF production capacity of 7,400 m³/h (177 MLD),
the SWRO facility will produce water for the city’s industry. An eight-month pilot period with
UF and other filtration technologies preceded the selection. During piloting Pentair X-Flow’s Surface Preparation
membranes showed outstanding performance. This, combined with the company’s track
record and project management capabilities, led to the selection of Pentair X-Flow.

THE SOLUTION
The client requirements chemical resistant, solvent free, non-slump adhesives for bonding
ceramic tiles to concrete and masonry in the pump stations, Fosroc has offered its product
that comply with the client Specs.

Nitotile 489 and Nitotile EP Grout has been offered by Fosroc and approved to be applied for
all the internal and external walls in the project Tile fix using Nitotile 489

THE BENEFITS
 As per client request proposed material given better satisfaction, especially non-
slump on vertical application.
 Made the consultant, client happy since, tile fixing was easy on vertical, even no need
to hold the tiles for fixing.
 Done the whole surface within the time limit.
 Nitotile 489 meets all the specification requirements by MARAFIQ. Completed project

T: +966 13 3623904 F: +966 13 3623875 E: fosam@fosroc.com

Address: Mashoor Street, Jubail, Saudi Arabia www.fosroc.com
Case History constructive solutions

 Project : Al Qadiseyah 115/13.8 Kw

Substation

 Client : SCECO

 Consultant : SATICH

 Contractor : AL Fanar Contracting Co.

 Sub Contractor: NON

 Location : Al Hasa - Hofuf – Qadiseyah Dst.

 Products :

Thioflex600 G.Grade 4 Ltr Nitomortar TC2000 55 Kg

Renderoc FC 600 Kg Nitoflor TF10000 1349 Kg
Renderoc HF 125 Kg Nitoflor FC150 4.5 Ltr
image of structure after completion
S/Cast Watafoil 200 135 Mtr Nitobond EP 1 Kg
Conbextra GP 4100 Kg Nitobond T.Adhes White 640 Kg
Nitoflor HartTop 350 Kg Nitotile EP Grout 12 Kg
Nitoflor SL4000 2550 Ltr Nitotile Grout Grey 60 Kg
Nitoprime 31 200 Kg Nitoseal HP40Sand 9000 Ml

 Execution Date : 2010

Background
For the ongoing and repaid growth of al Hasa area
generally and The cities of Hofuf and Mubarraz, SCECO
was faced of the area need of improving its services and
to increase the power substations.

Project Task
The construction of a new substation in Al Qadiseyah
district, aims to provide the growing area with stable and
continuous power supply to meet the growing needs.

Fosroc Repair Products were used all over the

project (Renderoc FC/HF, Conbextra GP, …etc) Constructive Solutions
As usual, we managed to provide the project with a wide
range of available constructive solutions, as it is above
mentioned. The project was provided with 95% of
chemical solutions from FOSROC.

Value to Client
FOSROC has the 1st priority among all the chemical
construction companies who were approaching the
project. This was due to FOSROC good reputation In
addition to reliable products, reasonable prices, fast
delivery and onsite and after sales service.
 Project Photos

Hardtop were applied to obtain a hard Huge areas of the substation, where
concrete surface Hardtop and Thioflex 600 were applied

Nitofloor SL4000 was applied as a self Nitofloor TF10000 was used beneath
levelling material beneath
. transformers heavy equipments

Fosam Co. Ltd. Tel: +966 2 60 80 999 Fax: +966 2 66 75 891 E-mail: Fosam@Fosroc.com
(Saudi Fosroc)
Regional Offices
Head Office Jeddah Sales Office Tel: (02) 6080999 Fax: (02) 635 3330 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Post Box 11081 Jeddah Showroom Tel: (02) 665 0787 Fax: (02) 667 4884 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Riyadh Tel: (01) 482 9303 Fax: (01) 482 9303 Medinah Tel: (04) 845 1767 Fax: (04) 846 3195
Jeddah – 21453 Dammam Tel: (03) 847 2929 Fax: (03) 847 1582 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875
www.Fosroc.com Saudi Arabia Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469