Nitotile EN*
constructive solutions
Polymer modified waterproof, tile adhesive, conforming
to EN specifications
Uses
Nitotile EN is a high-performance adhesive for the permanent
fixing of ceramic wall and floor tiles including porcelain and
fully vetrified tiles, ceramic mosaics, quarry tiles, dark natural
stone, terrazzo and brick slips. It can also be used for fixing of
insulating and acoustic boards based on expanded
polystyrene etc. Typical uses include :
! Wet areas - kitchens and bathrooms, swimming pools,
fountains.
! Tile claddings
Advantages
! Tropical grade to suit Middle East working conditions
! Good open wet time
! Good slip resistance
! High adhesive bond strength
Properties
Density
:
1.65 kg/m3
Tensile adhesion strength
(EN 1348 - stoneware tiles)
28d sc
: >1.5 N/mm2
7d sc+21d water
: >0.7 N/mm
14d sc+14d 70C+1d sc: >1.5 N/mm
Open time by tensile adhesion
strength (EN 1346-earthenware tiles)
5min
: >1.2 N/mm
20min
: >0.6N/mm
30 mins
: >0.5 N/mm
Transverse Deformation
(EN12002)
14 d 23C/95%RH+14 d sc
Deflection at max. force : >2.0 mm
Stress at max. force
: >2.0 N/mm
Deflection at break
: >2.5 mm
Stress at break
: >2.3 N/mm
! Water proof
! Good slip resistance
! Suitable in totally submerged conditions
Standards compliance
Nitotile EN conforms to EN12004 standard.
Instructions for use
Surface preparation
All surfaces must be sound and thoroughly clean before
Nitotile EN is applied. All traces of grease or oil must be
removed with a chemical degreaser. All loose particles of
mortar, old wallpaper, paint etc. must be physically removed.
Description
Surfaces
Nitotile EN cementitious based powder is available in grey or
white colour.
Nitotile EN can be applied directly on concrete, cement
screeds, and cement or lime mortar. Special attention must
be given to new construction prior to commencing tiling. Tiles
should not be placed on concrete or blockwork until all
shrinkage movement has taken place.
Technical support
Fosroc offers a comprehensive technical support service to
specifiers, end users and contractors. It is also able to offer
on-site technical assistance, an AutoCAD facility and
dedicated specification assistance in locations all over the
world.
Note :
To use Nitotile EN on gypsum or gypsum board
substrates, diluted Nitobond PVA (1 : 3 with water)
should be applied to the surface of the gypsum or
gypsum board prior to application of Nitotile EN.
Mixing
Nitotile EN*
6.25 litres of water is required for each 25 kg bag of
Nitotile EN. A slow speed drill fitted with a Fosroc Mixing
Paddle (MR4) and 30 litre mixing vessel are recommended.
Add powder to water and mix for 3 minutes until a uniform and
lump-free consistency is achieved.
Nitotile EN*
Application
Storage conditions
Nitotile EN should be spread on the substrate to a uniform
thickness of 2-6mm, and then combed horizontally.
Store in dry conditions in the original, unopened bags or packs.
If stored at high temperature and / or high humidity conditions
the shelf life may be reduced.
Place tiles firmly into adhesive bed, ensuring good contact
with a twisting motion. Only apply to areas which can be tiled
in the adhesives open wet time (normally up to 1m2 at a
time).
Joints
It is recommended that when fixing ceramic tiles, a minimum
spacing of 2mm be left around each tile.
Estimating
Supply
Nitotile EN
25 kg bags
Yield
Nitotile EN
Approx. 18.4 litres/ 25 kg bag
Note : Actual yield will vary according to water addition
Finishing
Remove excess adhesive with a damp cloth before the
material has set.
Cleaning
Nitotile EN should be removed from tools, equipment and
mixers with clean water immediately after use. Cured material
can only be removed mechanically.
Grouting
Grout installation should be after a minimum of 24 hours
curing time at 25C. Grout with Nitotile XS Grout*, depending
on the floor application.
Limitations
! Nitotile EN should not be used when the temperature is
below 5C and falling.
! The product should not be exposed to moving water
during application. If any doubt arise concerning
temperature or substrate conditions, consult your local
Fosroc office.
Precautions
Health and safety
Nitotile EN contains cement powders which, when mixed
with water or upon becoming damp, release alkalis which
can be harmful to the skin.
During use, avoid inhalation of the dust and contact with the
skin or eyes. Wear suitable protective clothing - eye protection,
gloves and respiratory equipment (particularly in confined
spaces).
The use of barrier creams to provide additional skin protection
is also advised. In case of contact with the skin, rinse with
plenty of clean water, then cleanse thoroughly with soap and
water.
In case of contact with eyes, rinse immediately with plenty of
clean water and seek medical advice. If swallowed seek
medical attention immediately - do not induce vomiting.
Fire
Nitotile EN is non-flammable
Storage
Shelf life
* Denotes the trademark of Fosroc International Limited
Nitotile EN has a shelf life of 12 months if kept in a dry store in
the original, unopened bags.
See separate data sheet
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard
Conditions for the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the users
responsibility to obtain the recent version. Refer to www.fosroc.com.
Al Gurg Fosroc
LLC
Post Box 657, Dubai
United Arab Emirates
www.fosroc.com
Head Office
telephone: (+9714) 2039699
fax: (+9714) 2859649
email: agf@fosroc.com
Regional offices
Abu Dhabi, Al Gurg Fosroc
Bahrain, YBA Kanoo
telephone: 673 1779
telephone: 17735454
fax: 673 1449
fax: 17732828
email: abudhabi@fosroc.com
email: bahrain@fosroc.com
Kuwait, Boodai
Oman, Al Amana
Qatar, Tadmur
telephone: 4817618
telephone: 24815080
telephone: 4500607
fax: 4832124
fax: 24817554
fax: 4500543
email: kuwait@fosroc.com
email: oman@fosroc.com
email: qatar@fosroc.com
UAE/0478/05/C
