Fosroc Nitotile LMT constructive solutions
Latex-modified, thick bed, tile adhesive
Uses Instructions for use
Nitotile LMT is a high quality adhesive for the permanent fixing Surface preparation
of tiles. Typical uses include :
All surfaces must be sound and thoroughly clean before
Wet areas - kitchens and bathrooms Nitotile LMT is applied. All traces of grease, oil and loose
particles of mortar, old wallpaper, paint etc. must be physically
Swimming pools
removed.
Fixing marble tiles
Surfaces
Fixing heavy elements e.g. brick slips, concrete tiles
Nitotile LMT can be applied directly on concrete, cement
Bridges, underpasses and high rise buildings screeds, and cement or lime mortar. Special attention must
be given to new construction prior to commencing tiling. Tiles
Advantages should not be placed on concrete or blockwork until all
shrinkage movement has taken place.
Formulated to suit Middle East conditions
Mixing
Enhanced bond and tensile strengths
Measure out 3.4 to 3.7 litres of clean water into a forced action
Good open wet time & slip resistance
mixer and add the liquid component, mix thoroughly until
Safe, economical and easy to use dispersed. With the mixer in operation, add the powder
component to the mix and continue mixing for 2 to 3 minutes
Water resistant - suitable for submerged conditions
until a uniform, lump-free consistency is achieved.
Early return to service
Application
Standards compliance Once mixed, Nitotile LMT is spread on the substrate to a
uniform thickness of 5-25 mm. This is then combed
Laboratory tests show Nitotile LMT conforms to BS5980:1980
horizontally.
Class AA Type 1.
Place tiles firmly into adhesive bed ensuring good contact
Description with a twisting motion. Only apply to areas which can be tiled
in the adhesive’s open wet time (up to 1m2 at a time).
Nitotile LMT is supplied as a two component pack, comprising
separate powder and liquid components, which requires only Joints
the on-site addition of clean water to produce a consistently
It is recommended that when fixing ceramic tiles, a minimum
high performance adhesive, compatible with most common
spacing of 2mm be left around each tile.
tile types.
Finishing
Properties
Remove excess adhesive with a damp cloth before material
Density : 1900 kg/m 3 has set. Joint grouting with Nitotile Grout* † may be
Tensile strength : 2 N/mm2 commenced 24 hours after tiles have been laid.
Shear adhesion : min 15 KN Cleaning
(to BS 5980:1980)
Minimum open time : 20 minutes Nitotile LMT should be removed from tools, equipment and
mixers with clean water immediately after use. Cured material
can only be removed mechanically.
Nitotile LMT
Fosroc Nitotile LMT
Limitations Precautions
Nitotile LMT should not be used when the temperature is Health and safety
below 5oC and falling. The product should not be exposed to
Nitotile LMT contains cement powders which, when mixed
moving water during application. If any doubt arise concerning
with water or upon becoming damp, release alkalis which
temperature or substrate conditions, consult your local Fosroc
can be harmful to the skin.
office.
During use, avoid inhalation of the dust and contact with the
Estimating skin or eyes. Wear suitable protective clothing - eye protection,
gloves and respiratory equipment (particularly in confined
Supply
spaces).
Nitotile LMT powder : 25 kg bags
Nitotile LMT liquid : 1 litre liquid The use of barrier creams to provide additional skin protection
is also advised. In case of contact with the skin, rinse with
Yield
plenty of clean water, then cleanse thoroughly with soap and
Nitotile LMT : 15.4 to 15.8 litres per 26 water.
kg pack (depending upon
water addition) In case of contact with eyes, rinse immediately with plenty of
clean water and seek medical advice. If swallowed seek
Storage medical attention immediately - do not induce vomiting.
Shelf life Fire
All products have a shelf life of 12 months if kept in a dry store Nitotile LMT is non-flammable
in the original, unopened bags.
Additional information
Storage conditions
Nitotile LMT is part of a range of Fosroc tile adhesive and tile
Store in dry conditions in the original, unopened bags or packs. grouts. In addition, Fosroc manufactures a range of
If stored at high temperature and / or high humidity conditions complementary products which includes waterproofing
the shelf life may be reduced. membranes, joint sealants, grouting, anchoring and
specialised flooring materials. Additionally, a wide range of
Technical support products specifically designed for the repair and
Fosroc offers a comprehensive range of high performance, refurbishment of damaged reinforced concrete is available.
high quality repair, maintenance and construction products. This includes hand-placed and spray grade repair mortars,
In addition, Fosroc offers a technical support package to fluid micro-concretes, chemical resistant epoxy mortars and
specifiers, end-users and contractors, as well as on-site a comprehensive package of protective coatings.
technical assistance in locations all over the world.
* Denotes the trademark of Fosroc International Limited
†
See separate data sheet
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to
obtain the recent version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
www.fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com
UAE/0283/08/D
